Owner's Manual

on the purchase of your NutriMill Harvest™. We paid special attention to optimizing its technical functionality and design. Before using the NutriMill

Harvest™, please read this owner’s manual carefully and keep these instructions. Please contact us if you require any further information.

Welcome to the NutriMill® Family.

Your Harvest™ mill is the perfect solution to provide you with fresh natural flours so you can affordably create delicious, healthy meals. Effortlessly grind non-oily whole grains, beans and legumes any time. These powerful “Super Food” flours

help you get the benefits of whole grain goodness in your daily diet.

The natural bamboo housing and high quality, ultra-strong, Corundum Grainmaster™ Millstones were manufactured with superior craftsmanship to ensure

many years of efficient milling.

NutriMill® – Giving you Superior Equipment for Healthy Meals™. Fresh is always better!

HOUSEHOLD USE ONLY

Technical InformationMillstones: Ceramic-Bound Corundum Millstone Ø: 3 inches Motor: 4 Amps; 450 WWeight: 16lbs

Housing: Bamboo Measurements: 7" W x 7" D x 13" HCapacity of Hopper: 3.5 cups Flour Fineness: Adjustable - Cracked to Pastry Fine

Please read all of these instructions thoroughly.– Keep small children away from mill at all times.– Avoid contact with moving parts on the mill.– To prevent hazardous operation or electric shock, DO NOT put motor base or

power cord in water or other liquids. – Keep mill and power cord away from stove or other heat sources.– The use of attachments not sold by or recommended by the manufacturer

may cause fire, electrical shock or other injury. – Turn off mill before unplugging from or plugging into an electrical outlet. – Be sure to turn switch to off position after every use. Make sure motor stops

completely before disassembling. – Mill should be unplugged from electrical outlet before cleaning, before

assembling or disassembling and when not in use.

DO NOT – unplug from electrical outlet by pulling on the cord. To unplug, grasp the plug

and pull. – put your fingers or other foreign objects into any of the mill’s openings while it is

in operation. – leave mill unattended while in use. – let cord hang over the edge of a table or counter or touch hot surfaces. – place on or near a hot gas or electric burner or in a heated oven.– clean mill by inserting pointed objects into milling chamber, or using running

water.– operate any appliance with a damaged cord or plug, or after appliance malfuntions or is dropped or damaged in any manner. Return appliance to nearest authorized service facility for a thorough examination, and any needed repairs, or electrical or mechanical adjustments. – use outdoors

IMPORTANT SAFEGUARDS

• chia seeds• sesame seeds• flax seeds• sunflower seeds

• nuts• sugar• dates/raisins• poppy seeds

• popcorn• tapioca• coffee beans• hemp nuts

• herbs & spices• chilies• goji berries• sprouted grains/beans (if not throughly dried)

DO NOT MILL ANY OF THE FOLLOWING

1

SAVE THESE INSTRUCTIONS

Turning the adjustment knob will control flour texture. Turn right (clockwise), for finer flour. (Fig. A) Turn left (counterclockwise), for coarser flour. (Fig. B)

1. Place mill on a hard, flat surface. Make sure ventilation slots are unobstructed. 2. Avoid areas with significant variations in temperature and humidity. 3. Verify existing voltage is 110v-120v. Plug in power cord. 4. Place bowl or container under flour outlet. 5. Turn on mill.6. Select grind texture setting. 7. Pour grain into hopper.8. When finished milling, turn switch off and unplug power cord.

ADJUSTING FLOUR TEXTURE

OPERATING INSTRUCTIONS

1. Grind about ¼ - ⅓ cup rice or wheat on a coarse setting. 2. Hold a vacuum cleaner tube against the flour outlet for a few seconds. Or use a dry brush to brush clean the millstones. NEVER USE WATER TO CLEAN STONES3. Millstones may be removed for occassional cleaning or replacing, if necessary. 4. Additional millstones can be purchased from the retailer where you purchased your mill. Those stones can be used as a replacement, or can be used as a set when milling for those with gluten intolerance, celiacs, or with other allergies or sensitivities.

CLEANING YOUR MILL

2

The adjustment knob can be turned in either direction at any time while milling. The markings on the adjustment knob will help you identify the proper texture. (Fig. C)

When adjusting to the finest texture you may hear the sound of the millstones coming in contact with each other. Making a slight adjustment to a coarser setting will eliminate that noise.

Under normal conditions, the mill can be turned off while grinding and restarted with grains in the hopper. If the motor does not spin, quickly turn the mill off. Adjust knob slightly (counterclockwise). Turn mill on and try again. If necessary, empty hopper and remove hopper and upper stone. For detailed instructions on removing millstones, see page 3.

Disassembly: 1. Turn off mill. Unplug from electrical outlet. 2. Turn hopper counter clockwise and lift off.3. Remove upper stone. 4. While holding lower stone, turn screw in the middle of the stone counter-clockwise using a 4 mm hex key, (wrench). 5. Lift rubber insert to remove lower stone from housing.

Reassembly: 1. Replace rubber insert by pushing outlet tube as far as possible into flour outlet in housing. 2. Next push down bottom of insert from front to back until insert is seated firmly in mill. You will need to align the three holes with the protruding tabs. 3. Put lower millstone onto motor shaft. Align flat sides on middle of millstone with flat sides of motor shaft. 4. Place washer over hole in lower millstone and insert screw. Turn screw clockwise (using hex key) until tight. 5. Set upper millstone in place, aligning tabs with slots in stone. Set hopper on mill and click into place (clockwise). Texture setting does not change during disassembly. Setting will remain the same as before removal of stones.

REMOVING MILLSTONES (FOR CLEANING OR REPLACING)

The Harvest™ mill is suited for milling all types of non-oily grains, beans and le-gumes. Avoid milling seeds or any grains, beans and legumes that have a high oil or moisture content.

If there is a question about grain being dry enough to mill, check using a “knife test”. Take a single piece of grain. With the flat side of a knife, press grain against a hard surface (like a countertop). Grain that bursts with a distinct cracking sound is dry enough to mill. Grain that is too wet will be soft and not crack or burst.

Know the source of your grain. Purchase and mill only carefully cleaned grain from a reliable source. Unclean grain may contain small stones, which can damage mill-stones.

Do not mill damp or wet grain. Damp grain may stick to millstones, block the flour outlet and affect your mill’s performance.

Note: Store grain in a dry, cool, well-ventilated location. Grain tends to absorb mois-ture from the air.

PURCHASE QUALITY GRAIN

3

L’Chef, LLC warrants the NutriMill® Harvest™ mill to be free of manufacturing defects in materials and workmanship for a period of 5 years. Defective product will be re-paired or replaced with a comparable model at our sole discretion upon receiving the defective product. L’Chef will not refund purchase price or provide any other remedy. This warranty applies to the original noncommercial purchaser.

Warranty does not cover damage resulting from accident, misuse, shipping, normal wear, commercial use, neglect, incidental or consequential damages, or from damage caused by any foreign objects getting into the mill.

YOU MUST keep a dated sales receipt for warranty service.

To ensure full warranty, return the mill, securely packed, to:

Include a copy of dated sales receipt, name, address information, phone number, email address and a statement giving specific reason for return.

For your convenience, there is a Request for Warranty Service Form located at www.boschkitchencenters.com. Click on the warranty button. For more information call customer service at 1.877.267.2434 or email service@lchef.com.

L’CHEFAttn: Service Dept. 825 N. Industrial Road St. George, UT 84770

Motor will not start.

Motor stalls during operation. This may be caused from overheating or improper use. The Harvest mill has a built-in thermal cut-off switch that stops the motor to prevent serious damage.Unusual smell or noise Milling heads rubbing during operation. Rotate the

adjustment knob to a coarser setting.

Rotate adjusting knob to coarse setting (counter-clockwise) until motor starts. Then adjust texture knob to desired setting. Unplug and allow mill to cool down. Remove hopper, empty any left over grains or legumes, and remove upper millstone. Make sure stones and milling chamber are clean and dry. Try re-starting motor with upper stone and hopper off. If the motor starts, turn off the mill. Reassemble and begin milling.

If problem persists, troubleshoot the source: • Is grain too moist? • Are millstones or mill chamber clogged? • Is a foreign object caught between the millstones? • Was the mill turned on when hopper was filled and millstones were at finest grind setting?

WARRANTY INFORMATION

TROUBLESHOOTING

4

For more information and recipes visit us online at boschkitchencenters.com

v1.2