ottoseal professional guide.pdf

OTTO Professional Guide

In building and faade constructionperfect sealing and bonding

3For your information

Preface

The building shell on a new building has undergone a pronounced transformation in recent years, both in housing construction and non-residential building. The trend towards energy-efficient facades has been reinforced by the use of glass and elements with insulation and improved heat gain characteristics, and it is set to become of increasing importance in the future.

However, the major focus of the construction work is the renovation of old buildings. And one basic prerequisite for a functional faade is expansion joints which compensate the movements of the building and structural elements, as well as preventing damage from occurring due to the weather.

In the case of major building projects it is sometimes necessary to erect parts of buildings separately for structural reasons. The joints between these buildings must then be classified as joints that separate buildings and it is their function to compensate the movements of the parts of the building. Joints of this type can be sealed by means of elastomer tapes. Injectable sealants are not suitable in this case.

By contrast, faade sealing comes under the scope of DIN 18540 or DIN EN ISO 11600. Such joints in concrete faades, unplasteredbrickwork and/or natural stone do not function as compensation between parts of buildings; they have a sealing function within the faades.

Preface 3

Information on Faade Joints 4-9

Perfect sealing and bonding 10-17

Professional accessoires by OTTO 18-19

Exact calculation of the quantities required 20

General valid joint dimension 21

OTTO Professional Guide 23

4 Information on faade joints

Standards and guidelines for expansion joints in building construction

The relevant standards for expansion joints in building construction are the DIN 18540 Sealing of exterior wall joints in building using joint sealants and DIN EN ISO 11600, Building construction joint-sealing products Classification and requirements of sealants.

In DIN 18540 the classification F (= fast stability) is important for the optimal suitability of the sealant for use in outdoor joints susceptible to the weather. In DIN EN ISO 11600 the highest classification, 25 LM, means 25 % elasticity and a sealing compound which displays good recovery with little strain (= Low Modulus). This characteristic is also important for use in faades owing to temperature fluctuations and the impact of the weather because it affects the thermal length variation of faade elements.

5Information on faade joints

Maximum joint width between concrete faade sections in building construction

The maximum recommended joint width for joints in building construction is 35 mm. Correct joint dimensions are calculated according to the table below:

Joint dimensions table

Joint width Depth of joint sealant3)

Distance between joints in m

Nominal dimension1) bF in mm

Minimum dimension2)

in mmtD

in mmLimiting dimensions

in mm

up to 2 15 10 8 2

above 2 to 3,5 20 15 10 2

above 3,5 to 5 25 20 12 2

above 5 to 6,5 30 25 15 3

above 6,5 to 8 354) 30 15 3

1) Nominal dimensions for the planning2) Minimum dimension at the time a joint is sealed3) The stated values apply to the final state, whereby the change in volume of the joint sealant must be borne in mind4) For larger joint widths attention must be paid to the instructions of the sealant manufacturer


Fire protection in building construction

According to DIN 4102 this is the standard pertaining to the fire behaviour of building materials and building components building materials are classified either as building material class A or B.

Non-combustible building materials belong in building material class A. Class A is subdivided again. The composition of A1 building materials must be entirely non-combustible, while A2 building materials are permitted to contain a small amount of combustible constituents. The combustible building materials belong in class B. Class B for combustible building materials is divided into difficult to ignite (B1), normally combustible (B2) and easily ignited (B3).

In building construction building materials must at least conform to class B2 for building materials. Our sealants, OTTOSEAL M 360, OTTOSEAL P 305 and OTTOSEAL S 110 are classified as B2, normally combustible building materials in compliance with the definitions in DIN 4102 Part 4.

The following OTTO silicones belong in building material class B1 (difficult to ignite):

OTTOSEAL S 94 The fire protection silicone if fire behaviour requirements are higher, e. g. for fire-retardant components

OTTOSEAL S 42 The 2-component laminated glass edge bond as the secondary edge bond for the production of UV-resistant insulated glass units

OTTOSEAL S 54 The special B1 silicone e. g. for connection joints for mastic asphalt screeds or difficult adhesive bases, such as asphalt, bitumen etc. and for the equalising bonding of materials such as glass, stainless steel, aluminium and some plastics

Compatibility of sealants with coatings in compliance with DIN 5242

If faades are made from materials other than natural stone and/or glass, as a rule they are given an exterior coating. Walls inside buildings are also normally given a coat of paint. Therefore sealants which are compatible with coats of paint are needed for both indoor and outdoor joints.

Definition of compatibility with coatings

Compatibility with coatings means that the paint can overlap with the joint sealant by approximately 1 mm without any negative reactions taking place between the two materials. As a rule it is not possible to paint over the sealant because the (rigid) coating would crack owing to the expanding movements of the (elastic) sealant.

The OTTO products OTTOSEAL M 350, OTTOSEAL P 305 and OTTOSEAL S 110 are very compatible with coatings in compliance with DIN 52452.

IVD leaflets

The OTTO sealants for use in building construction and faades are also suitable for applications in accordance with the following IVD leaflets.

OTTOSEAL P 305 and OTTOSEAL M 360:

No.7 (10/06 issue) Elastic joint seal on faades made from cemented-on ceramic tiles

No.9 (02/08 issue) Injectable sealants in the connection joint for windows and exterior doors


Apart from nos. 7 and 9, OTTOSEAL S 110 also complies with the following leaflets:

No.10 (02/08 issue): Sealing glass on wooden windows by means of sealants

No.13 (02/08 issue): Sealing glass on wood-aluminium windows by means of sealants

Compatibility with natural stone

Soiling of natural stones because of the migration of material out of the joint-sealing compound into the stone is an aesthetically undesirable occurrence. The risk of contamination by the joint sealant material is tested in compliance with the ASTM C 1248 standard of the American National Standards Institute, ANSI. We have therefore had our premium natural stone silicone, OTTOSEAL S 70, tested by DL Laboratories, New York in compliance with ASTM C 1248. We can guarantee that OTTOSEAL S 70 is compatible with natural stone.


Prevention of contamination and damage from moisture on faades

Hydrophobicity of faades causes a great reduction in the absorption of water, good UV resistance and very good running-off characteristics. The ready-to-use OTTO Siloxan 290L solution can be applied directly by spraying or brushing it on. The substrate should be more or less dry and free of moss, mould or algae for processing.

The differences in the water absorption capacity of building materials are significant.

Water absorption untreated(approximate average, depending on material quality)

Water absorption hydrophobised with OTTO Siloxan 290L(approximate averages depending on material quality)

Concrete 3 % 0,8 %

Sandstone 5 % 0,2 %

Lime sand brick 13 % 0,8 %

Limestone 12 % 1,1 %

Clinker 3 % 0,1 %

Brick 18 % 0,1 %

Tuff 18 % 1,1 %

Mortar 7 % 1,2 %

Weathered surfaces with blooming should be pretreated by sand or steam blasting or washing them off using suitable cleaning agents. Neighbouring components such as windows, doors, roof gutters etc. must be covered over. The two applications are carried out from top to bottom, wet on wet.

The hydrophobic faade is rainproof after approximately 24 hours. The hydrophobic effect prevents moisture from entering the interior from the outside, but allows interior moisture to escape to the outside. The hydrophobic effect lasts several years; however it depends on the state of the faade, the cardinal direction and hence the intensity of the weathering.

Glass rebate sealing on wooden windows

Optimal sealing of the glass rebates on wooden windows is subject to some important factors:

The fast stability of the sealant is important for avoiding cracks in the sealing. These can arise if, for example, sealing is carried out in direct sunlight and at a high temperature and the temperature drops thereafter and the sealant then has to follow the movements of the components although it is not yet fully cured.

OTTOSEAL S 110 and S 120 form a firm surface skin very fast and can therefore follow the movements on the building after only a short time. Furthermore, compatibility with the building materials within the contact range of the sealant (e.g. varnishes or stains) is extremely important.

They must not damage or stain the sealant. According to the relevant standards and recommended practice it is not possible to completely coat the sealant (refer to section: Compatibility of sealants with coatings in compliance with DIN 5242).


Abrasion resistance must comply with DIN 18545, part 2. OTTOSEAL S 110 and S 120 meet the requirements of group E sealants. After the sealant has been smoothed, the residual smoothing agent must be removed immediately. Otherwise streaks may remain.

The sealant must cure for three days before it is cleaned for the first time in order to prevent the seal from being damaged. The surface of the sealant should be cleaned with a moist, soft textile cloth using normal commercial window-cleaning agents.

OTTOSEAL S 110 and OTTOSEAL S 120 meet the maximum requirements of ISO 11600, i.e. they conform to the 25 LM classification. Furthermore, they also comply with the French CTBA L 114 standard (Suitability of sealants for sealing glass rebates on wooden windows).

Standards for adhesives in wood construction

DIN EN 204 D4

This European standard specifies the assessment of adhesives for bonding wood and wood materials in the case of non-structural components. Categorisation in class D4 is equivalent to the highest class for adhesives. OTTOCOLL P 84, P 85 and P 86, and OTTOCOLL Rapid, P 410 and P 520 comply with said class D4.

DIN EN 14257 (formerly WATT 91)

This standard pertains to wood adhesives and the determination of tensile strength of lap joints in a tensile test at elevated temperatures. This evidence of conformity is particularly important in the weathered area in order to keep bonds functional in the long term.

10 Perfect sealing and bonding

OTTOSEAL M 360

The hybrid sealant for expansion joints

Characteristics:1-component sealant based on silane-terminated polymers (hybrid)Compatible with coatings according to DIN 52452Good weathering and ageing resistanceCures without bubble formationLow odourFree of isocyanatesSilicone-freeStress expansion modulus at 100 % (DIN 53 504, S3A): 0,4 N/mm2

Fields of application:External joints according to DIN 18540-FSealing of joints on faades, metal constructionsExpansion joints on prefabricated concrete and cellular concrete unitsBonding of OTTO Window Tapes BAB/A and BAB/I on masonry, concrete, cellular concrete etc.

Standards and tests:Tested according to DIN EN ISO 11600 F 25 LM (ift Rosenheim, germany)Suitable for applications according to IVD instruction sheet no. 7+9+19-1+20+22+24+27 (IVD = German industry association sealants)Quality seal of the IVD (Industrial association for sealants, registered society), tested by the ift Rosenheim (Institute of window engineering, registered society)According to regulation (EG) Nr. 1907/2006 (REACH)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

LEED OTTOSEAL M 365

The hybrid adhesive and sealant

Characteristics:1-component adhesive and sealant based on silane-terminated polymers (hybrid)Compatible with coatings according to DIN 52452Good weathering and ageing resistanceVery good adhesion on many types of materials such as plastics, metals, wood and derrived timber products, concreteCures without bubble formationLow odour

Free of isocyanatesSilicone-free

Fields of application:For application in interior and exterior areasExternal joints according to DIN 18540-FSealing of joints on faades, metal constructionsSealing of joints on windows and doors made of wood, metal and plasticElastic bonding and mounting of various materials such as wood, derived wood products, glass, metals (e. g. aluminium, stainless steel, anodising aluminium, brass, copper), plastics (e. g. unplasticised PVC, fibrereinforced plastics etc.), mineral substrates (e. g. brick, tile, ceramic), fireproof building panels (gypsum board etc.)For the bodywork and vehicle construction, waggon and container construction, metal construction and apparatus engineering, ship building

Standards and tests:According to the requirements of ISO 11600 F 25 LMSuitable for applications according to IVD instruction sheet no. 7+9+19-1+20+22+24+27 (IVD = German industry association sealants)French VOC-emission class A+Certified according to GOS

11Perfect sealing and bonding

OTTOSEAL P 305

The premium PU sealant

Characteristics:1-component sealant based on polyurethaneCures without bubble formationGood weathering and ageing resistanceCompatible with coatings according to DIN 52452Silicone-freeStress expansion modulus at 100 % (DIN 53 504, S3A): 0,3 N/mm2

Fields of application:External joints according to DIN 18540-FExpansion joints on prefabricated concrete and cellular concrete units

Sealing of faades, metal constructions, window and door connections, flat roof parapets

Standards and tests:Tested and monitored according to DIN 18540-F (Sddeutsches Kunststoff-Zentrum, Wrzburg, Germany)Suitable for applications according to IVD instruction sheet no. 7+9+20+22+24+27 (IVD = German industry association sealants)Quality seal of the IVD (Industrial association for sealants, registered society), tested by the ift Rosenheim (Institute of window engineering, registered society)According to regulation (EG) Nr. 1907/2006 (REACH)French VOC-emission class A+Certified according to GOS

OTTOSEAL S 7

The weather sealing silicone

Characteristics:Neutral-curing 1-component silicone sealantExcellent weathering, ageing and UV-resistanceLong skin-formationUser-friendly matt surfaceHigh resistance to notches, tension and tearingExcellent adhesion on many substrates, partly in combination with primerCompatible with PVB-foils according to the criteria of the ift-guideline DI-02/1Compatible with insulating glass edge bond sealing based on silicone

Non-corrosive

Fields of application:Specially developed for the weather sealing of structural glazing, angled glazing, wood-glass-composite units, roof glazing and conservatoriesSuitable for sealing glazing unitsSuitable for joints on insulating glass units

Standards and tests:According to the requirements of DIN 18540-FAccording to the requirements of ISO 11600 F 25 LMSuitable for applications according to IVD instruction sheet no. 22 (IVD = German industry association sealants)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

LEED


The premium natural stone silicone

Characteristics:Neutral-curing 1-component silicone sealantGuarantee - does not cause any migratory staining on natural stoneHigh resistance to notches, tension and tearingExcellent weathering, ageing and UV-resistanceNon-corrosiveContains fungicidesAlso in structure colours with a stonelike surfaceAlso available in matt-finished coloursMatt colours are only to be smoothed off dry

Stress expansion modulus at 100 % (DIN 53 504, S3A): 0,5 N/mm2

Fields of application:Sealing and jointing on marble and all natural stones, e. g. sandstone, quartzite, granite, gneiss, porphyry etc. in interior and exterior areasSealing of expansion joints in wall and faade areasMovement-compensating bonding of natural stone on metal, e. g. stairs on a metal constructionSealing and jointing of marble / natural stone swimming pools, also underwater jointsSealing of lacquered and enamelled glassFor the external sealing of mirrors in connection with natural stone

Standards and tests:Tested according to ISO 16938-1 of SKZ Wrzburg (Testing for migratory staining of sealants on natural stone)Tested according to ASTM C 1248 by DL Laboratories, New York (Testing for migratory staning of sealants on natural stone)Highly recommendable non-hazardous building product according to building material list (TOXPROOF) of the TV Rheinland, GermanySuitable for applications according to IVD instruction sheet no. 14+23+25+27 (IVD = German industry association sealants)Quality seal of the IVD (Industrial association for sealants, registered society), tested by the ift Rosenheim (Institute of window engineering, registered society)According to regulation (EG) Nr. 1907/2006 (REACH)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

OTTOSEAL S 70 LEED

The constructional adhesive/sealant

Characteristics:Neutral-curing 1-component silicone sealant and adhesiveExcellent weathering, ageing and UV-resistanceExcellent adhesion on many substrates, partly in combination with primerNon-corrosiveHigh resistance to notches, tension and tearingCompatible with PVB-foils according to the criteria of the ift-guideline DI-02/1

Fields of application:Sealing of expansion joints in building constructionAlso suitable for weather sealing of structural glazing, angled glazing, wood-glass-composite units, roof glazing and conservatoriesSuitable for sealing glazing unitsInstallation of X-ray protective glassElastic bonding and sealing in the electrical industry, in mechanical engineering, vehicle construction and shipbuildingNot suitable for the structural bonding of structural glazing units

Standards and tests:The manufacturer has tested and confirmed the compatibility to strainless Plexiglas. Test report on the compatibility with plexiglas-XT is availableTested and recommended by Schott Desag AG Deutsches Spezialglas, D-31073 Grnenplan, for the installation of RD 50 and RD 30 X-ray protective glassUL 94 Flame Classification HB, RTI 105 C, File No. E 176319Suitable for applications according to IVD instruction sheet no. 22 (IVD = German industry association sealants)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

OTTOSEAL S 10 LEED

PREMIUM


The premium neutral silicone

Characteristics:Neutral-curing 1-component silicone sealantExcellent weathering, ageing and UV-resistanceExcellent early resistance to stressHighly abrasion-resistant and non-streakyGood compatibility with paints according to DIN 52452 (not paintable)Tack-free surfaceExcellent adhesion on many substrates, partly in combination with primerNon-corrosiveContains fungicidesCompatible with PVB-foils according to the criteria of the ift-guideline DI-02/1

Stress expansion modulus at 100 % (DIN 53 504, S3A): 0,4 N/mm2

Fields of application:Window pane sealing on wooden windowsSealing of joints on windows and doors made of wood, metal and plasticSealing double-glazings (e. g. Profilit)Expansion joints on prefabricated concrete and cellular concrete unitsSealing of joints on faades, metal constructionsSuitable for sealing glazing unitsExpansion joints in bathroom areas

Standards and tests:Tested according to DIN 18545, part 2, resistance group E (ift Rosenheim, Germany)According to the requirements of DIN 18540-FAccording to the requirements of ISO 11600 G 25 LMTested according to FCBA (CTBA) L 114 (suitability of sealants for window pane sealing on wooden windows)Highly recommendable non-hazardous building product according to building material list (TOXPROOF) of the TV Rheinland, GermanySuitable for applications according to IVD instruction sheet no. 7+9+10+13+14+19-1+20+22+24+25+27 (IVD = German industry association sealants)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

OTTOSEAL S 110 LEED OTTOSEAL S 125

The constructional alkoxy silicone

Characteristics:Neutral-curing 1-component silicone sealant based on alkoxyNon-corrosiveGood adhesion on ceramic substratesContains fungicidesExcellent weathering, ageing and UV-resistanceStress expansion modulus at 100 % (DIN 53 504, S3A): 0,4 N/mm2

Fields of application:Sealing of joints on windows and doors made of wood, metal and plastic

Expansion joints in prefabricated concrete constructionsSealing of facades, parapet elements, roller blind housings and metal building constructionsExpansion joints in bathroom areasFor the external sealing of mirrors in connection with materials such as ceramic, metal, glass etc.

Standards and tests:Suitable for applications according to IVD instruction sheet no. 3+7+9+14+19-1+20+24+25+27 (IVD = German industry association sealants)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

LEED

PREMIUM


The precompressed jointing tape

Characteristics:Impregnated foam tape, self-adhesive on one sideStretches slowly inside the joint to its final thicknessForms a driving rain resistant joint according to DIN 18542Good UV-resistanceFlame resistant

Protects against moisture and dust, heat loss, noise etc.Compatible with concrete, cellular concrete, bricks, sandlime brick, iron, zinc, steel, galvanised sheet metal, aluminium, copper, wood and unplasticized PVCCompatible with many dispersion faade paintings and compatible with many OTTO sealants based on silicone, dispersion acrylic, hybrid and polyurethane. In case of use on marble and other natural stones please contact our technical service department in advance

Fields of application:Sealing of jointsJoint between masonry and door or window framesJoint between masonry and concrete pillars, gable and roofing panels, sheet metal window sills, expanding joints, sheet pile profiles and corrugated panels

Standards and tests:BG1 according to DIN 18542Driving rain resistant up to 600 Pa according to DIN EN ISO 1027Compatible with general construction material according to DIN 18542Tested and monitored (MPA BAU Hannover, Germany) according to DIN 4102-B1 - flame resistant between massive mineralic constructional elementsSuitable for applications according to IVD instruction sheet no. 24+26 (IVD = German industry association sealants)French VOC-emission class A+

OTTO Fugenband BG1OTTO Siloxan 290 L

The silicone for surface impregnation

Characteristics:Ready-to-use silicone surface impregnationHigh penetration depthUV-resistantCan also be applied on moist substrates (not rain-wet)Forms a water- and dirt-repelling surfaceThe hydrophobe effect prevents the penetration of moisture from the outside to the inside but it lets the internal moisture escape to the outside

Bridges hair cracks up to a width of 0,3 mmReduces the tendency of treated surfaces to pick up dirtAvoids humidity in the construction material thus avoids salt efflorescence as well as moss and algae growthPaintable with commercial dispersion paintsLow odourColourlessSlight deepening of colour is possible

Fields of application:Hydrophobic treatment of faades and building components made of concrete, cellular concrete, fibre cement, brick-work, natural and artificial stone, mineralic plasters and coatingsDrainage of moist and cracked surfaces, which are then painted using dispersion paintsOnly for vertical surfaces

15

The precompressed insulating tape

Characteristics:Impregnated foam tape, self-adhesive on one sideStretches slowly inside the joint to its final thicknessForms a driving rain resistant joint according to DIN 18542Good UV-resistanceProtects against moisture and dust, heat loss, noise etc.

Compatible with concrete, cellular concrete, bricks, sandlime brick, iron, zinc, steel, galvanised sheet metal, aluminium, copper, wood and unplasticized PVCCompatible with many dispersion faade paintings and compatible with many OTTO sealants based on silicone, dispersion acrylic, hybrid and polyurethane. In case of use on marble and other natural stones please contact our technical service department in advance

Fields of application:Sealing of joints against sound, driving rain, dust, draft and heat loss.Especially suitable for joint constructions as in e. g. coupled windows, hidden window joints to define a boundary for sealants

Standards and tests: BG 2 according to DIN 18542Driving rain resistant up to 600 Pa according to DIN EN ISO 1027Compatible with general construction material according to DIN 18542Tested according to DIN 4102-B2 - normally flammableSuitable for applications according to IVD instruction sheet no. 24+26 (IVD = German industry association sealants)French VOC-emission class A+

OTTO Dmmband BG2

Perfect sealing and bonding

OTTOCOLL M 570

The 2-component hybride mounting adhesive

Characteristics:The 2-component hybrid-poly-mer-based (STPU) adhesiveFast curing even in thick layersExcellent primerless adhesion on numerous substrates - even when exposed to waterFor stress-compensating bon-ding and dynamic stressesHigh resistance to notches, tension and tearingLow odourFree of isocyanatesSilicone-free

Good weathering and ageing resistanceCompatible with coatings according to DIN 52452

Fields of application:For application in interior and exterior areasElastic bonding and mounting of various materials such as wood, derived wood products, glass, metals (e. g. aluminium, stainless steel, anodising aluminium, brass, copper), plastics (e. g. unplasticised PVC, plasticised PVC, fibrereinforced plastics etc.), mineral substrates (e. g. brick, tile, ceramic), fireproof building panels (gypsum board etc.)For the bodywork and vehicle construction, waggon and container construction, metal construction and apparatus engineering, ship buildingSealing of air condition and ventilation systemsBonding of stone, natural stone and ceramicElastic bonding of mirrors on ceramic, glass, plastic, stainless steel, aluminium, wood, concrete etc.

Standards and tests:French VOC-emission class A+Certified according to GOS


OTTOCOLL P 86

The 1-component PU adhesive for corner connections

Characteristics:1-component adhesive based on polyurethaneExcellent adhesion on metalsLong skin-formationFills cavities optimally foaming slightlyTensile strength after 7 days - approx. 14.000 N (ift-test certificate)Only for commercial users. Please observe the material safety data sheet

Fields of application:General bonding in metal construction

Weathering resistant bonding of corner joints on metal windows, doors and faades as well as conservatoriesBonding of modified wood

Standards and tests:Tensile strength tested by the ift Rosenheim, Germany (institute for window techniques)According to the requirements of DIN EN 204-D4 to weathering resistant bondings of wood and derived wood productsAccording to the requirements of DIN EN 14257 (WATT 91) to temperature-resistant bondings of wood and derived wood productsExpertise about the use of OTTOCOLL P 86 translucent for bonding modified wood (Georg-August-University Gttingen, Germany)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

The hybrid-adhesive for full-surface bonding

Characteristics:1-component sealant based on silane-terminated polymers (hybrid)Free-flowingExcellent primerless adhesion on numerous substrates - even when exposed to waterGood weathering and ageing resistanceFor stress-compensating bonding and dynamic stressesLow odourFree of isocyanatesSolvent-freeSilicone-free

Compatible with coatings according to DIN 52452

Fields of application:For application in interior and exterior areasElastic bonding and mounting of various materials such as wood, derived wood products, glass, metals (e. g. aluminium, stainless steel, anodising aluminium, brass, copper), plastics (e. g. unplasticised PVC, plasticised PVC, fibrereinforced plastics etc.), mineral substrates (e. g. brick, tile, ceramic), fireproof building panels (gypsum board etc.)For the bodywork and vehicle construction, waggon and container construction, metal construction and apparatus engineering, ship building

Standards and tests:French VOC-emission class A+Certified according to GOS

OTTOCOLL M 590


OTTOCOLL P 520

The premium 2-component PU adhesive

Characteristics:2-component adhesive based on polyurethaneFast curing even in thick layersNon-shrink curingExcellent adhesion on metalsExtremly high tensile strength after 24 hours - approx. 14.000 (ift-test certificate)Only for commercial users. Please observe the material safety data sheet

Fields of application:Weathering resistant bonding of corner joints on metal windows, doors and faades as well as conservatoriesGeneral bonding in metal constructionAlso suitable for firm bonding of very different materials such as wood, metal, plastics, stone etc.

Standards and tests:Tensile strength tested by the ift Rosenheim, Germany (institute for window techniques)According to the requirements of DIN EN 204-D4 to weathering resistant bondings of wood and derived wood productsAccording to the requirements of DIN EN 14257 (WATT 91) to temperature-resistant bondings of wood and derived wood productsConform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

LEED

18 Professional accessoires by OTTO

OTTO Marble Silicone Smoothing Agent

Characteristics:Aquaeous solution of surface-active substancesEspecially attuned to delicate marble and natural stone varietiesReduces the risk of staining from smoothing agents to a minimumGentle on the skin due to dermatolo-gically tested active ingredientsDoes not dry out the skinKeeps the shine of the sealant surface intactColouring pigments of the sealant are not washed offUse in undiluted condition only

Fields of application:Smoothing of sealants in contact with natural stone

OTTO Smoothing agent

Characteristics:Aquaeous solution of surface-active substancesGentle on the skin due to dermato-logically tested active ingredientsDoes not dry out the skinDilutable with water; 2 (smoothing agent) : 1 (water)Keeps the shine of the sealant surface intactColouring pigments of the sealant are not washed offNot suitable for marble and other natural stones

Fields of application:Smoothing of sealant surfaces including silicone, polyurethane and MS hybrid polymer sealants

Note: For marble and other natural stones, please use the OTTO marble-silicone-smoothing agent

OTTOCORD PE-B2 back up foam rod

Characteristics:Extruded back-filling poly-urethane (PE) material. For interior and exterior applications. With closed cells according to DIN 18540. Water repellent. Colour: anthracite.Coresponds to building material class B2 (normal flammability).

Fields of application: For pre-filling and pre-plugging interior and exterior joints. For tenders in comliance with DIN 18540.

OTTO Cleaner

Characteristics:Very good cleansing and degreasing effect. No airing necessary. Dries fast and free of residue.

Fields of application:Cleaning glass, metals and some plastics, such as PVC and polyester.

OTTO Primer

Characteristics: Primer specially made to be used with OTTO sealants.

Fields of application: Improving the adhesive properties of OTTO silicone sealants to the relevant substructures.

OTTO Fugenboy

Smoothing tool made of superior plastics for professional joint design. Set of three, small: 5 mm, 8 mm, round. Set of three, big: 11 mm, 14 mm and 17 mm.

19Professional accessoires by OTTO

Hand-operated Gun H37

Heavy duty hand-operated gun made of highly impact-resistant plastic, very lightweight. With closer for sliding sleeve, smooth driving rod and sliding sleeve for 290/300/310 ml cartridges. Automatic pressure relief.

Hand-operated Gun H 400 (COX)

Hand-operated gun, aluminium cylinders. For foil bags up to 400 ml. Ladder hook available separately. No spare part service.

Compressed Air Gun P 400 Air3 (COX)

Compressed air gun with ergonomically designed gun handle. Aluminium cylinder for foil bags up to 400 ml. Not suitable for cartridges.

Compressed Air Gun P 620 Air3 (COX)

Compressed air gun with ergonomically designed gun handle. Aluminium cylinder for foil bags up to 620 ml. Not suitable for cartridges.

20 Exact calculation of the quantities required

Note: This values are approximate and serve as a rough guide for rightangled joints. The depth of the joints is measured to the rear of the profile.

Metres per 300/310 ml cartridge

5 7 10 12 15 20 25 12 8 6 6 4 3 3 2,5 2,0 1,5 2,1 1,7 1,2 1,0 1,3 1,0 0,8

57

101215

Joint width [mm]

Join

t d

epth

[mm

]

Joint width [mm]

Join

t d

epth

[mm

]

5 7 10 12 15 20 25 15 10 8 8 5 4 4 3 2,6 2,0 2,7 2,2 1,6 1,3 1,7 1,3 1,0

57

101215

5 7 10 12 15 20 2523 15 11 11 7 6 6 5 4 3 4 3 2,4 2,0 2,5 1,9 1,4

57

101215

Joint width [mm]

Join

t d

epth

[mm

]

Metres per 400 ml aluminium foil bag

Metres per 580 ml aluminium foil bag

21General valid joint dimension

b

td

Source: Industrieverband Dichtstoffe e.V. / HS PR. Additional information to the IVDs infor-mation leaflets under www.ivd-ev.de

b

t

10-15

8 2

15-20

10 2

20-25

12 2

25-30

15 3

30-35

15 3

Joint width b in ration of joint depth t [mm]

The rule of thumb for calculating the joint dimension is as follows:

Sealant depth (t) =0,5 x joint width (b).

The thickness of the sealant (d) equals 2/3 of the joint width (b).

22 For your notes

23OTTO Professional Guide

How to perfectlyseal floor coverings

OTTO Manual for Professionals

How to make a perfect job of mould prevention


How to make perfect joints in natural stone


How to makeperfect joints


How to waterproof

wetrooms perfectly


Part n 9999533 Part n 9999557 Part n 9999875 Part n 9999568 Part n 9999551

Choosingthe perfect adhesive


Part n 9999754

Bonded windowsPerfectly accomplished


Part n 9999574


In building and faade constructionperfect sealing and bonding

Part n 9999801

24

Ind

ex:

9999

801-

GB

-19.

06.2

013

H

erm

ann

Ott

o G

mb

H 2

013

OTTO Head officeTel.: 0049-8684-908-540Fax: 0049-8684-908-549E-mail: [email protected] UK: 0800-783 60 53

OTTO Technical ServiceTel.: 0049-8684-908-460Fax: 0049-8684-908-469E-mail: [email protected]

OTTO Order processingTel.: 0049-8684-908-310Fax: 0049-8684-908-319E-mail: [email protected]

In order to ensure a quick and correct handling of your orders we would like to ask you to send them by fax or e-mail. Thank you in advance for your cooperation.

For further information please contact:

Hermann Otto GmbH Krankenhausstr. 14 83413 Fridolfing, GERMANY

Tel.: 0049-8684-908-0 Fax: 0049-8684-1260

E-mail: [email protected] Internet: www.otto-chemie.com

Your specialised dealer:

Notes:The information in the present document corresponds to the status quo on going to print, refer to the index. With a new edition this edition becomes invalid. Due to the many possible influences during and after application, the customer always has to carry out trials first. Please observe the respective technical data sheet! This information is available on the Internet at www.otto-chemie.com. Errors and typographical errors are excepted.

OTTO product information

The OTTOFLEX system consists ofPrimer

Protective coatingSlurry Seal Coating

Sealing TapeWall Sealing Sleeve

Floor Sealing SleeveExterior Corners

Interior Corners

Cleaner Primer

Back-up foam rods/back-filling material

Hand-operated guns Smoothing Agent

Fugenboy Marble and natural stone

degreasing paste

OTTO accessories for the pro

Ind

ex:

9999

403-

GB

-06.

08.2

013

Her

man

n O

tto

Gm

bH

20

13

Permanently waterproof

More informationfrom specialist suppliers

Suppliers stamp

Find out about the other OTTO products for sealing and bonding at www.otto-chemie.com

Hermann Otto GmbH Krankenhausstr. 14 83413 Fridolfing, GERMANYTel. +49-(0)8684-908-0 Fax +49-(0)8684-1260

E-Mail [email protected] www.otto-chemie.com


with the guarantee not to cause

migratory staining

The pros choice for joints in natural stone

Notes:The information in the present document corresponds to the status quo on going to print, refer to the index. With a new edition this edition becomes invalid. Due to the many possible influences during and after application, the customer always has to carry out trials first. Please observe the respective technical data sheet! This information is available on the Internet at www.otto-chemie.com. Errors and typographical errors are excepted.

OTTOSEAL S 70This highly notch-resistant special sealant avoids ugly migratory staining around the edges of the joint on marble, granite, sandstone etc. and it is also ultimately suitable for applications in constantly wet areas and even under water, e.g. swimming pools. After curing it is elastic but yet hard wearing. OTTOSEAL S 70 practically stays forever young even in sun, wind and weather. This silicone contains fungicides and is available on stock in many structure colours with stonelike surfaces. Some of the most popular colours like manhattan, anthracite and sanitary grey are also available in a matt finish.

Characteristics:Neutral-curing 1-component silicone sealantGuarantee - does not cause any migratory staining on natural stoneHigh resistance to notches, tension and tearingExcellent weathering, ageing and UV-resistanceNon-corrosiveContains fungicidesAlso in structure colours with a stonelike surfaceAlso available in matt-finished coloursMatt colours are only to be smoothed off dryStress expansion modulus at 100 % (DIN 53 504, S3A): 0,5 N/mm2

Fields of application:Sealing and jointing on marble and all natural stones, e. g. sandstone, quartzite, granite, gneiss, porphyry etc. in interior and exterior areasSealing of expansion joints in wall and faade areasMovement-compensating bonding of natural stone on metal, e. g. stairs on a metal constructionSealing and jointing of marble / natural stone swimming pools, also underwater jointsSealing of lacquered and enamelled glassFor the external sealing of mirrors in connection with natural stone

Standards and tests:Tested according to ISO 16938-1 of SKZ Wrzburg (Testing for migratory staining of sealants on natural stone)Tested according to ASTM C 1248 by DL Laboratories, New York (Testing for migratory staning of sealants on natural stone)Highly recommendable non-hazardous building product according to building material list (TOXPROOF) of the TV Rheinland, GermanySuitable for applications according to IVD instruction sheet no. 14+23+25+27 (IVD = German industry association sealants)Quality seal of the IVD (Industrial association for sealants, registered society), tested by the ift Rosenheim (Institute of window engineering, registered society)According to regulation (EG) Nr. 1907/2006 (REACH)Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealantsFrench VOC-emission class A+Certified according to GOS

The most important featuresat a glance

The pro leavesno traces

S 70 The premium natural stone silicone

OTTOSEALS 70

Technical Datasheet

Characteristics: - Neutral-curing 1-component silicone sealant- Guarantee - does not cause any migratory staining on natural stone- High resistance to notches, tension and tearing- Excellent weathering, ageing and UV-resistance- Non-corrosive- Contains fungicides- Also in "structure" colours with a stonelike surface- Also available in "matt-finished" colours- Matt colours are only to be smoothed off dry- Stress expansion modulus at 100 % (DIN 53 504, S3A): 0,5 N/mm2

Fields of application: - Sealing and jointing on marble and all natural stones, e. g. sandstone, quartzite, granite, gneiss,porphyry etc. in interior and exterior areas

- Sealing of expansion joints in wall and faade areas- Movement-compensating bonding of natural stone on metal, e. g. stairs on a metal construction- Sealing and jointing of marble / natural stone swimming pools, also underwater joints- Sealing of lacquered and enamelled glass- For the external sealing of mirrors in connection with natural stone

Standards and tests: - Tested according to ISO 16938-1 of SKZ Wrzburg (Testing for migratory staining of sealants onnatural stone)

- Tested according to ASTM C 1248 by DL Laboratories, New York (Testing for migratory staning ofsealants on natural stone)

- "Highly recommendable non-hazardous building product" according to building material list(TOXPROOF) of the TV Rheinland, Germany

- Suitable for applications according to IVD instruction sheet no. 14+23+25+27 (IVD = German industryassociation sealants)

- Quality seal of the IVD (Industrial association for sealants, registered society), tested by the iftRosenheim (Institute of window engineering, registered society)

- According to regulation (EG) Nr. 1907/2006 (REACH)- Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealants- Fulfills DGNB-characteristics 06 (DGNB e.V. = German Organisation for sustainable building)- French VOC-emission class A+- Certified according to GOS- Declaration in "baubook" Austria

Important information: Before applying this product the user has to ensure that the materials in the area of contact (solid, liquidand gaseous) are compatible with it and also amongst each other and do not damage or alter (e. g.discolour) each other. As for the materials that will be used at a later stage in the surrounding area of theproduct the user has to clarify beforehand that the substances of content or evaporations do not lead toan impairment or alteration (e. g. discolouration) of the product. In case of doubt the user should consultthe respective manufacturer of the material.

Technical Datasheet OTTOSEAL S 70Page 1version: 41 / 26gb (18.12.2013, 8:39 h)

Hermann Otto GmbH Krankenhausstr. 14 83413 Fridolfing, GERMANYTel.:+49 8684-908-0 Fax: +49 8684-12-60e-mail: [email protected] Internet: www.otto-chemie.de

During the curing process of the material reaction products of the crosslinker are released.Ensure good ventilation during application and curing.After curing the product is completely odourless, physiologically harmless and unmodified.The required vulcanization time prolongs with increasing thickness of the silicone layer. One-componentsilicones must not be used for full-surface bonding applications unless special constructionalprerequisites are met. If one-component silicones are to be used for thickness layers of more than 15mm please contact our technical department beforehand.Remark on the processing of the colour "stainless steel": Please note that when "modelling" the silicone,i. e. when silicone layers are pushed on top of each other (e. g. in corner areas) dark, clearly visibledividing lines could appear. These dividing lines can not be removed by smoothing the lines afterwards.This effect occurs solely for the colour "stainless steel" and is caused by a special colour pigment whichis necessary to create the metallic effect. It is a typical characteristic of the colour "stainless steel" and itdoes not represent a deficiency of the material. In order to avoid such effect, layers of silicone shouldnot be pushed on top of each other when smoothing material.Matt-finished colours have to be rebated dry, in order to keep the matt-effect on the surface.Smoke from cigarettes or similar environmental influences may lead to discolouring of the sealant.Avoid contact with materials which contain bitumen and which release solvents, e. g. butyl, EPDM,neoprene, insulating- and bituminous paint.Upon restoring of joints contaminated with mould the existing elastic sealant must be removedcompletely. Before re-jointing, the affected jointing areas are to be treated with OTTO Anti-Mildew Sprayto remove possibly existing fungal spores. Otherwise a new mould attack may occur in the joints again,despite the mould protection technology of the sealant. Please observe the Technical Datasheet ofOTTO Anti-Mildew Spray.

Technical properties: Skin-forming time at 23 C/50 % RAH [minutes] ~ 5 Curing in 24 hours at 23 C/50 % RAH [mm] ~ 3 Processing temperature from/to [C] + 5 / + 35 Viscosity at 23 C pasty, stable Density at 23 C according to ISO 1183-1 [g/cm] ~ 1,0 Shore-A-hardness according to ISO 868 ~ 30 Permissible movement capability [%] 20 Stress expansion modulus at 100 % according to ISO 37, S3A [N/mm] ~ 0,5 Tensile expansion according to ISO 37, S3A [%] ~ 400 Tensile strength according to ISO 37, S3A [N/mm] ~ 1,4 Temperature resistance from/to [C] - 40 / + 180 Extrusion rate according to ISO 8394-1 [g/min.] ~ 85 - 105 Shrinkage of volume according to ISO 10563 [%] < 10 Shelf life at 23 C/50 % RAH for cartridge/foil bag [months] 15

These data are not suitable for the issue of specifications. Please contact OTTO-CHEMIE before issuingspecifications.

Pretreatment: The adherent surfaces have to be clean, free from fat, dry and sustainable.All adherent surfaces must be clean and any contaminant such as release agents, preserving agents,grease, oil, dust, water, old adhesives or sealants and other substances which could affect adhesion,should be removed. Cleaning of non-porous substrates: Apply OTTO Cleaner T (airing time approx. 1minute) using a clean, lint-free cotton cloth. Cleaning porous substrates: Clean surfaces with steel-wirebrush e. g. or a grinding disk to remove loose particles.

Primer Table: The demands on elastic sealings and bondings depend on the respective exterior influences. Extremefluctuations in temperature, tensile or shear forces, repeated contact with water etc. demand highrequirements of a bonding. In such cases it is advisable to apply primer according to therecommendations of our technical department (e. g. +/OTTO Primer 1216) in order to achieve a resilientbonding.The OTTO Primer 1215, 1217 and 1218 are subject to the obligation to inform and to keep recordsaccording to the German Regulation of Chemical Interdiction (amongst others prohibition of self service)since 01.11.2005. Please observe the Technical Data Sheets (www.otto-chemie.com).

ABS T Acrylic glass/PMMA (Plexiglas, etc.) T Acrylic bathroom surfaces (e. g. bath tubs) + / 1101 Aluminium +



Aluminium anodized + Aluminium powder-coated 1101 / T Aluminium powder-coated (contains teflon) T Concrete 1105 / 1215 / 1218 Concrete block 1216 Lead + Stainless steel 1216 Iron + Epoxid resin coating + / 1216 Glass + Wood, painted (solvent systems) + Wood, painted (aquaeous systems) + Wood, varnished (solvent systems) + Wood, varnished (aquaeous systems) + Wood, untreated + (1)Ceramic, glazed + (2)Ceramics, unglazed + Artificial stone + / 1216 Plastic profiles (unplasticized, e. g. Vinnolit) + / 1227 Copper + / 1216 (3)Melamine formaldehyde resins (e. g. Resopal) + / 1216 Brass + / 1216 (3)Natural stone + / 1216 (4)Polyester + Polypropylene T Cellular concrete 1105 / 1215 Plaster + / 1105 / 1215 PVC unplasticized 1217 / 1227 PVC-soft-foils + / 1217 / 1227 Sandstone 1102 Tinplate 1216 Zinc, galvanised iron 1216

1) Upon high exposure to water please contact our Technical Department.2) When using ceramic tiles with a special surface coating such as Ceramicplus of Villeroy + Boch we recommend apre-treatment with OTTO Cleanprimer 1226. When using ceramic tiles with other surface coatings it is advisable tocontact our Technical Department or make preliminary tests.3) The reaction of neutral silicone with non-ferrous metalls, such as copper, brass, etc. is possible. Upon curing un-blocked air admission is necessary.4) Depending on the nature of external influences and the kind of natural stone it may be necessary to use a primer.For natural stone in contact with water (i.e. bathrooms and showers) we generally advise the use of OTTOPrimer1216. For jointing natural stone in swimming pools and sauna's and also for other applications under waterplease contact our technical department.

+ = good adherence without primer- = not suitableT = Test/pilot test advised

Application information: Especially with unpolished natural stone surfaces make sure not to spread the sealant beyond the joins,as the sealant is difficult to remove once it enters the pores of the natural stones.For smoothing use OTTO Marble Silicone Smoothing Agent (undiluted). Wash / remove excess agentimmediately. We do not recommend the use of usual smoothing agents (e. g. dishwashing detergentsetc.) because of the high sensibility to staining of some marble and natural stone varieties.Due to the many possible influences during and after application, the customer always has to carry outtrials first.Please observe the recommended shelf life which is printed on the packaging.We recommend to store our products in unopened original packagings dry (< 60 % RAH) attemperatures of +15 C up to +25 C. If the products are stored and / or transported at highertemperatures / air humidity for longer periods (some weeks), a diminuition of durability or a change ofmaterial characteristics may arise.

Packaging: 310 ml cartridge 400 ml aluminium foil bag



adria blue S70-04-C990 on requestanthracite S70-04-C67 S70-07-C67

anthracite grey S70-04-C137 on requestautumn-grey S70-04-C1108 on requestbahamabeige S70-04-C10 S70-07-C10

black S70-04-C04 on requestbrown S70-04-C05 on request

chinchilla S70-04-C45 on requestconcrete grey S70-04-C56 S70-07-C56

dark green S70-04-C37 on requestfair blue structure S70-04-C44 on requestfair-grey structure S70-04-C109 on request

flash grey S70-04-C787 on requestfog S70-04-C230 on request

galaxy S70-04-C4720 on requestgraphite black S70-04-C1391 on request

grey-blue structure S70-04-C47 on requestgrey-red structure S70-04-C41 on request

jasmin S70-04-C08 on requestjoint-grey S70-04-C71 on request

joint-grey structure S70-04-C110 on requestlabrador blue S70-04-C1390 on request

light-grey S70-04-C38 on requestmanhattan S70-04-C43 on request

matt anthracite grey S70-04-C6116 on requestmatt bahamabeige S70-04-C6115 on request

matt black S70-04-C6114 on requestmatt concrete grey S70-04-C6113 on request

matt jasmin S70-04-C6117 on requestmatt manhattan S70-04-C1282 on request

matt sanitary grey S70-04-C6111 on requestmatt white S70-04-C6112 on request

matt-anthracite S70-04-C1300 on requestnight-grey S70-04-C1109 on requestpearl-grey S70-04-C80 S70-07-C80pergamon S70-04-C84 on requestred-beige S70-04-C82 on request

sand-red structure S70-04-C32 on requestsandstone-beige S70-04-C1110 on request

sanitary grey S70-04-C18 S70-07-C18silver-green structure S70-04-C34 on request

stainless steel S70-04-C197 on requestsunset S70-04-C26 on request

thistle-grey structure S70-04-C111 on requesttransparent S70-04-C00 S70-07-C00

white S70-04-C01 S70-07-C01Packaging unit 20 20

Pieces per pallet 1200 900

Safety precautions: Please observe the material safety data sheet.

Disposal: Information about disposal: Please refer to the material safety data sheet.

Warranty information: All information in this publication is based on our current technical knowledge and experiences.However, since conditions and methods of use and application of our products are beyond our control,we suggest you to test the product before final use. Information given in this technical data sheet andexplanations of OTTO - CHEMIE in connection with this technical data sheet (e. g. service description,reference to DIN regulations etc.) is not to be seen as a warranty. Warranties require a separate writtendeclaration of OTTO CHEMIE to prove their validity. The characteristics stated in this data sheetdefine the characteristics of the article broadly and concludingly. Suggestions of use are not to be taken



as confirmation of the appropriateness for the recommended intended use. We reserve the right to alterthe product adjusting it according to technical progress and new developments. We are at your disposalboth for inquiries as well as specific application problems. If a governmental approval or clearance isnecessary for the application of our products, the user is responsable for the obtainment of such. Ourrecommendations do not excuse the user from the obligation to take into consideration the possibility ofinfringement of third paries' rights and - if necessary resolving it. For the rest our general terms andconditions apply, in particular regarding a possible liability for deffects. You can find our general termsand conditions on our homepage: http://www.otto-chemie.com.



/5Safety data sheet

according to 1907/2006/EC, Article 31Printing date 21.07.2011 Revision: 21.07.2011

DR

* 1 Identification of the substance/mixture and of the company/undertaking

Product identifier Trade name: OTTOSEAL S 70 Application of the substance / the preparation Silicone sealant Details of the supplier of the safety data sheet Manufacturer/Supplier:Hermann Otto GmbHKrankenhausstrae 14D-83413 FridolfingTel.: 0049/(0)8684/908-0Fax.: 0049/(0)8684/908-539

Further information obtainable from:Tel.: 0049- (0)8684- 908- 641 ( -460 )E-Mail: [email protected]

Emergency telephone number: Tel.: 0049- (0)89- 192 40 (emergency telephone no.)

* 2 Hazards identification

Classification of the substance or mixture Classification according to Directive 67/548/EEC or Directive 1999/45/EC not applicable Information concerning particular hazards for human and environment:Preparation is not hazardous in terms of directive 1999/45/EU.

Classification system:The classification is according to the latest editions of the EU-lists, and extended by company andliterature data.

Label elements Labelling according to EU guidelines:Observe the general safety regulations when handling chemicalsThe product is not subject to identification regulations under EU Directives and the Ordinance onHazardous Materials (German GefStoffV).

Special labelling of certain preparations:Contains mixture of butanone oximosilanes and butanone oxime. May produce an allergic reaction.Ensure good ventilation during application and curing.Safety data sheet available for professional user on request.

Other hazardsDuring the application and curing process of the material chemicals are released as vapour (seeitem 11). Therefore ensure good ventilation or exhaustion if necessary.

Results of PBT and vPvB assessment PBT: Not applicable. vPvB: Not applicable.

3 Composition/information on ingredients Chemical characterization: Mixtures Description: Polydimethylsiloxane, filler, auxiliaries and oximosilane crosslinker

Dangerous components:CAS: 2224-33-1EINECS: 218-747-8

Butanonoximvinylsilan Xi R37/38-41; Xi R43

< 2.5%

CAS: 22984-54-9EINECS: 245-366-4

butan-2-one 0,0'0''-(methylsilylidyne)trioxime Xn R21; Xi R36/38; Xi R43

< 2.5%

CAS: 128446-60-6 3- Aminopropyl ( methyl )silsesquioxane, ethoxy- terminiert Xi R36/38

R10

< 2.5%

(Contd. on page 2) GB

/5Safety data sheet


Trade name: OTTOSEAL S 70

(Contd. of page 1)

DR

Additional information For the wording of the listed risk phrases refer to section 16.

* 4 First aid measures

Description of first aid measures After inhalationSupply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor ifsymptoms persist.

After skin contactImmediately wash with water and soap and rinse thoroughly.If skin irritation continues, consult a doctor.

After eye contactRinse opened eye for several minutes under running water. Then consult a doctor.

After swallowingDo not induce vomiting; call for medical help immediately. Show container or label.Rinse out mouth and then drink plenty of water in small amounts (if person is conscious).

5 Firefighting measures Extinguishing media Suitable extinguishing agentsCO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.

Special hazards arising from the substance or mixtureFormation of toxic gases is possible during heating or in case of fire.

Advice for firefighters Protective equipment:Mount respiratory protective device.Do not inhale explosion gases or combustion gases.

* 6 Accidental release measures Personal precautions, protective equipment and emergency proceduresEnsure adequate ventilation

Environmental precautions: Do not allow to enter sewers/ surface or ground water. Methods and material for containment and cleaning up:Dispose contaminated material as waste according to item 13.Pick up mechanically.

Reference to other sections See Section 8 for information on personal protection equipment.

7 Handling and storage

Handling Precautions for safe handlingEnsure good ventilation/exhaustion at the workplace.see item 8: Personal protective equipment

Conditions for safe storage, including any incompatibilities Storage Requirements to be met by storerooms and receptacles: Prevent any seepage into the ground. Information about storage in one common storage facility: Store away from foodstuffs. Further information about storage conditions:Store in cool, dry conditions in well sealed receptacles.Protect from heat and direct sunlight.

GB

(Contd. on page 3)

/5Safety data sheet



(Contd. of page 2)

DR

* 8 Exposure controls/personal protection

Additional information about design of technical facilities: No further data; see item 7. Control parameters Ingredients with limit values that require monitoring at the workplace:The product does not contain any relevant quantities of materials with critical values that have to bemonitored at the workplace.

CAS No. Designation of material % Type Value Unit Additional Occupational Exposure Limit Values for possible hazards during processing:67-56-1 methanolWEL Short-term value: 333 mg/m, 250 ppm

Long-term value: 266 mg/m, 200 ppmSk

Additional information:The lists valid during the making were used as basis.Maximum concentration at workplace recommended by producer: methyl ethyl ketoxime (MEKO,CAS: 96-29-7, product of hydrolysis) = 3 ppm .

Exposure controls Personal protective equipment General protective and hygienic measuresThe usual precautionary measures are to be adhered to when handling chemicals.Wash hands before breaks and at the end of work.Avoid contact with the eyes and skin.

Respiratory protection:Not necessary if room is well-ventilated.Use suitable respiratory protective device in case of insufficient ventilation.

Protection of hands: Protective gloves. Material of glovesThe selection of the suitable gloves does not only depend on the material, but also on further marksof quality and varies from manufacturer to manufacturer.Fluorocarbon rubber (Viton)Nitrile rubber, NBRNatural rubber, NR

Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves andhas to be observed.

Eye protection: Safety glasses Body protection: Protective work clothing.

* 9 Physical and chemical properties

Information on basic physical and chemical properties General Information Appearance:

Form: pastyColour: According to product specification

Odour: Characteristic Self-igniting: Product is not selfigniting. Danger of explosion: Product does not present an explosion hazard. Density at 20C: 1.01 g/cm Solubility in / Miscibility with

Water: Not miscible or difficult to mix GB

(Contd. on page 4)

/5Safety data sheet



(Contd. of page 3)

DR

10 Stability and reactivity

Reactivity Chemical stability Thermal decomposition / conditions to be avoided:No decomposition if used according to specifications.Avoid strong heating.

Possibility of hazardous reactions No dangerous reactions known Hazardous decomposition products:Tests on representative products have shown that above temperatures of 150 C small quantitiesof formaldehyde are split off.see item 5.3

* 11 Toxicological information

Information on toxicological effects Acute toxicity: Primary irritant effect: on the skin: Irritating effects to skin and mucous membranes possible on the eye: Irritating effect possible Other information (about experimental toxicology):During the application of the product butanone-2-oxime (MEKO) is released. MEKO might affectthe mocous membrane of the nose by long time exposition. If MEKO is breathed in highconcentrations over a long period (e.g. in case of insufficient ventilation), it might cause irreversiblehealth defects.After curing the material is odourless and completely harmless.

Additional toxicological information:When used and handled according to specifications, the product does not have any harmful effectsto our experience and the information provided to us.Product has not been tested. Assessment analogue to a similar product.

* 12 Ecological information Toxicity Acquatic toxicity: No further relevant information available. Persistence and degradability Other information: Product is not biodegradable. Additional ecological information: General notes:Water hazard class 1 (German Regulation) (Self-assessment): slightly hazardous for water.Do not allow product to reach ground water, water course or sewage system.

Results of PBT and vPvB assessment PBT: Not applicable. vPvB: Not applicable.

13 Disposal considerations

Waste treatment methods RecommendationObserve local by-laws.Already cured material can be disposed of with the domestic or commercial waste.Unconsumed material (fluid, paste-like) is to dispose of as hazardous waste.

(Contd. on page 5) GB

/5Safety data sheet



(Contd. of page 4)

DR

Uncleaned packaging: Recommendation:Empty contaminated packagings thoroughly. They may be recycled after thorough and propercleaning.Packagings that may not be cleansed are to be disposed of in the same manner as the product.

* 14 Transport information

Land transport ADR/RID (cross-border) ADR/RID class: - Maritime transport IMDG: IMDG Class: - Marine pollutant: No Air transport ICAO-TI and IATA-DGR: ICAO/IATA Class: - Special precautions for user Not applicable. Transport/Additional information: Not dangerous according to the above specifications. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code Not applicable.

15 Regulatory information

Safety, health and environmental regulations/legislation specific for the substance ormixture

National regulations Waterhazard class: Water hazard class 1 (Self-assessment): slightly hazardous for water. Chemical safety assessment: A Chemical Safety Assessment has not been carried out.

16 Other informationThis information is based on our present knowledge. However, this shall not constitute a guaranteefor any specific product features and shall not establish a legally valid contractual relationship.

Relevant phrasesR10 Flammable.R21 Harmful in contact with skin.R36/38 Irritating to eyes and skin.R37/38 Irritating to respiratory system and skin.R41 Risk of serious damage to eyes.R43 May cause sensitisation by skin contact.

Department issuing MSDS: Tel.: 0049- (0)8684- 908- 641 Contact: Tel.: 0049- (0)8684- 908- 641 ( -460 ) * Data compared to the previous version altered.

GB

Use of US Green Building Council Member logo does not imply that USGBC has approved this confirmation or any mentioned product.Use of that logo just states that Eurofins Product Testing A/S is member of US Green Building Council.

Eurofins Product Testing A/S Smedeskovvej 38 DK 8464 Galten / Denmark

Tel +45 70 22 42 76 Fax +45 70 22 42 75

www.product-testing.eurofins.com

CCoonnffiirrmmaattiioonnEurofins Product Testing A/S confirms that a sample of a Architectural Sealant with the name

OOTTTTOOSSEEAALL SS 7700supplied by

HHeerrmmaann OOttttoo GGmmbbHH

showed low VOC contents in a test as specified in LEED credit EQ 4.1 (adhesives and sealants).

VOC contents were below the limit value specified as 250 grams VOC minus water per liters for architectural sealant.

The test has been performed in October 2010, see test report no. G04612.

Volatiles content was calculated by Eurofins. Water content was specified by manufacturer. Solids content was determined by Eurofins.

With this confirmation, use of product OTTOSEAL S 70 may qualify for fulfillment of LEED credit EQ 4.1 (adhesives and sealants).

29 Oktober 2010

_____________________Inge Bondgaard Chemical engineer

The test results relate only to the items tested. The report shall not be reproduced except in full without the written approval of the testing laboratory.

\\DK02FIVA\SAGER\2010\G04\G04612\06-REPORTS\G04612_HERMANN OTTO_LEED EQ 4_DOC.DOC Page 1 of 1

Hermann Otto GmbH Alois Parzinger Krankenhausstr. 14 83413 Fridolfing Germany

Test Report LEED EQ 4.1 - 2009

Sample material Sample identification OTTO SEAL S 70

Product type Architectural Sealant

Product data, according to manufacturer Density: 1.01 g/ml at 20 C

Date received 20 September 2010

Analytical period October 2010

Methods applied Method Principle Parameter Detection limit Uncertainty

LEED EQ 4.1-2009

ASTM D 2369 - 04 Gravimetric Volatile/Solid Content of Coatings 1 g/l 0.1 %

Volatile content of the sample was determined gravimetrically by heating up to 110 C during 60 minutes. The result is the average of triple testing. The result was calculated as:

( [g all volatiles] - [g water] - [g exempt compounds] ) / ( [l material] - [l water] - [l exempt compounds] )

Analytical results

Solid content,% mass

Water content,% mass

VOC less water less exempt com-

pounds, g/l VOC limit g/l

OTTO SEAL S 70 92,9% 0 ** 72 250 *

* VOC limit for Architectural Sealants. ** Given by the client.

Eurofins Product Testing A/S

Inge Bondgaard Chemical engineer

Eurofins Product Testing A/S

Smedeskovvej 38

DK-8464 Galten

Denmark

Tel. +45 70 22 42 76

Fax +45 70 22 42 75

[email protected]

www.eurofins.com/product-emissions

Date

15 October 2010

Your ref.

-

Our ref.

G04612/IB

Tost report no.:

Customer:

Order:

Letter of:

Sample recoipt:

88717/09

Hermann Otto GmbHKankenhausslrae 1 48341 3 FridomngGERMANY

Determination of the stainingbyjoint sealants according to

2009-01-13

2010-0115

201041-18 to 2010-03-19

of substratesISO 16938-1:2008

Rof: Mr. Thomas Keuntie

Tst po od:

This test report consists of 4 pages.

wzburg, 2010-0+14SC/JWt

'"0 az,Dr. Anton Zahn

(-_)i . A.

/ t t /l/L./. ' '-

Wolfgang Ries

The reprcduction, duplicarion orrranslation of rhis repon as a whole or in pans lor advenising pwposes is not Pemited withoutlhe wittnapp.ovalofSKZ -TeConAGmbH.The results only applytoe productsteslod. Tle accreditations are onlyvalid lorthe standads tnd me$odslisted in tio crblicates.The lktofsllstandardslorwhich wo arc ac*edited is shoM one homspag at9^e.skz de

sKz,rsconacmbH Gsschttsihmr rel.: +ts e31 41or'0 ll ff'H-*Testnq, OualityAssuraic, Conification Drlng. Markus K. Lak Far +49 931 41 04_477 lEllrla\l =lFriedtich-Be.qiusning 22 HRB 7&10 E_Mail: [email protected] -t oAP eL ggro.oo97lt6 WEtu.q Amtsgeichtwzburg s/W.skz.de DAP rS 2005.00

:

:

t .

Pags 2 of4Tst rpon no.: 8871 7/09

Ordor

By letter of January '13, 2010, the company Hermann Otto GmbH, ltankenhausstrae14, 83413 Fridolling, GERMANY instructed SKZ - TeConA GmbH to determine thestaining of substrates byjoint sealants according to ISO 16938-1:2008.

Test material

On 15 January 2010 SKZ - TeConA GmbH received following samples for testing:2.

2 cartridgesDesignation:Base mateial:Charge:Colour:

one-component silicone joint sealantOTTOSEAL@ S7Oneutral curing RTV-1 silicone sealant oxime-based91129311white

20 specimens Bianco Canara 25 x 70 mm

8 specimens Bianco Canara 12 x 70 mm

Test procodre

Testing of a one-componenl-silicon-sealant OTTOSEAL@ S70 was carried out accord-ing to ISO 16938-1:2008

Unless otherwise noted all tests were canied out at standard atmosphere 23150, class1 according to DIN EN ISO 291.

Usually we carry out tests according to standards for which we have an accreditation.The list of all standards for which we are accredited is showl on the homepage atwww.skz.de.

Test specimen preparation and pre-treatment

As substrates specimens Bianco Canara with the dimensions 25 x 70 mm and '12 x 70mm, provided by the producer, were used. The manufacturing of the test samples wascanied out without a orimer.

The pretreatment of the samples was canied out according to ISO 16938-1, 28 days at(23 t 2) 'C and (50 t 5) % rel. humidityAfter the pretreatment, all samples had been compressed by 20%. (to 9.6 mm)

of4Test repod no.: 8871 709

3.1 Staining after heat aging

The test was canied out according to ISO 16938-1, item 8.2.2., with the samples beingstored for 14 and/or 28 days heat aging at 70'C (+/- 2'C).

3.2 Staining after cold aging

The test was canied out according to lso 16938-1, item 8.2.3., with the samples beingstored for 14 and/or 28 days at 20 "C (+/- 2'C).

3.3 Staining after artificial weathering

This test was canied out according to DIN EN ISO 16938-1, item 8.2.4., procedure b)with the samples being stored in a weathering device according to lso 11431, item8.2.2 with automatic weathering cycle . The aging was carried out for '14 days and/or28 days.

The irrdiation was canied out even during water spraying phase.

Parameters of wealhring dsvice

Type of weathering device: XENO 1200 cPSLight source: Xenon-arc sourceFilter system: Tenestrial daylight simulationBlack standard temperature: 60 r 3 'CWhite standard temDerature: 40 - 45 'CRelative humidity: 65 i 5 o/oSpray cycle: 18 min wate. spray, 102 min dry cyclelnadiation energy EUV (300 - 400) nm: 60 t 2 W/m'Exposure period: 693 h respectively 352 hTotal inidation: 1350 MJ respectively 675 MJ

After the artificial weathering, the specimens were stored for 24 h at standard condi-tioning atmosphere 23150, class 1. Afterwards the determination of staining was caniedout according to ISO 16938-1, item 9.

PegE 4 ot,{Tst ramrl no.: 88717/09

T.st rcsultB

Sub!ffi Samplono.

14 daya 28 days

mlnlmumstaining in

maximum6tdnln9In

ninlmumstaining In

mm

mafmumdalnlng In mm

70.c

EancoCanarawhite

1 0 0 0 0

0 0 0 0

-2VCBiancoCatraravvhite

1 0 0 0 0

2 0 0 0 0

wrqtherlng

BiancoCarrarawhib

0 0 0 0

2 0 0 0 0

i -- -: -: : a'--,-'

:.-.

96

S 70

S 130 - S 140 - X-GLM

OTTOSEAL S 70

Guarantee

no migratory

staining

Other quantities and special colours on request. Please observe the technical and security data sheets www.otto-chemie.com


Characteristics:Neutral-curing 1-component silicone sealant

Guarantee does not cause any migratory staining on natural stone

High resistance to notches, tension and tearing

Excellent weathering, ageing and UV-resistance

Non-corrosiveContains fungicidesAlso in structure colours with a stonelike surface

Also available in matt finished colours

Matt colours are only to be smoothed off dryStress expansion modulus at 100 % (DIN 53 504, S3A): 0,5 N/mm2

Fields of application:Sealing and jointing on marble and all natural stones, e. g. sandstone, quartzite, granite, gneiss, porphyry etc. in interior and exterior areas

Sealing of expansion joints in wall and faade areasMovement-compensating bonding of natural stone on metal, e. g. stairs on a metal construction

7 new

matt colou

rs

Colour 310 mlCartridge400 ml Alum.

Foil Bagadria blue S70-04-C990 on requestanthracite S70-04-C67 S70-07-C67anthracite grey S70-04-C137 on requestautumn-grey S70-04-C1108 on requestbahamabeige S70-04-C10 S70-07-C10black S70-04-C04 on requestbrown S70-04-C05 on requestchinchilla S70-04-C45 on requestconcrete grey S70-04-C56 S70-07-C56dark green S70-04-C37 on requestfair-blue structure S70-04-C44 on requestfair-grey structure S70-04-C109 on requestPackaging unit 20/Box 20/BoxPieces per pallet 1,200 900


Foil Bagflashgrau S70-04-C787 on requestfog S70-04-C230 on requestgalaxy S70-04-C4720 on requestgraphite black S70-04-C1391 on requestgrey-blue structure S70-04-C47 on requestgrey-red structure S70-04-C41 on requestjasmin S70-04-C08 on requestjoint-grey S70-04-C71 on requestjoint-grey structure S70-04-C110 on requestlabrador blue S70-04-C1390 on requestlight-grey S70-04-C38 on requestmanhattan S70-04-C43 S70-07-C43Packaging unit 20/Box 20/BoxPieces per pallet 1,200 900

Sealing and jointing of marble / natural stone swimming pools, also underwater joints

Sealing of lacquered and enamelled glassFor the external sealing of mirrors in connection with natural stone

Standards and tests:Tested according to ISO 16938-1 of SKZ Wrzburg (Testing for migratory staining of sealants on natural stone)

Tested according to ASTM C 1248 by DL Laboratories, New York (Testing for migratory staning of sealants on natural stone)

Highly recommendable non-hazardous building product according to building material list (TOXPROOF) of the TV Rheinland, Germany

Conform to LEED IEQ-credits 4.1 (Indoor Environmental Quality) adhesives and sealants

Suitable for applications according to IVD instruction sheet no. 14+23+25+27 (IVD = German industry association sealants)

Quality seal of the IVD (Industrial association for sealants, registered society), tested by the ift Rosenheim (Institute of window engineering, registered society)According to regulation (EG) Nr. 1907/2006 (REACH)French VOC-emission class A+

97Other quantities and special colours on request. Please observe the technical and security data sheets www.otto-chemie.com

C00transparent

C43manhattan

C6112matt white

C34silver-green

structure

C1391 graphite black

C1110sandstone-beige

C01white

C18sanitary grey

C6117matt jasmin

C32 sand-red structure

C4720galaxy

C82red-beige

C38light-grey

C56concrete grey

C6115matt

bahamabeige

C41grey-red structure

C10bahamabeige

C787flash grey

C1109night-grey

C1282 matt

manhattan

C109fair-grey structure

C26sunset

C230fog

C137anthracite grey

C6111matt

sanitary grey

C110joint-grey structure

C05brown

C80pearl-grey

C67anthracite

C6113matt

concrete grey

C111thistle-grey structure

C37dark green

C1108autumn-grey

C04black

C6116matt

anthracite grey

C44fair-blue structure

C990adria blue

C71joint grey

C08jasmin

C1300matt anthracite

C47grey-blue structure

C197 stainless steel

C45chinchilla

C84pergamon

C6114matt black

C1390labrador blue

New New New New New New New

Textured colours

Matt colours

New


Foil Bagmatt anthracite S70-04-C1300 on requestmatt anthracite grey S70-04-C6116 on requestmatt bahamabeige S70-04-C6115 on requestmatt concrete grey S70-04-C6113 on requestmatt jasmin S70-04-C6117 on requestmatt manhattan S70-04-C1282 on requestmatt sanitary grey S70-04-C6111 on requestmatt black S70-04-C6114 on requestmatt white S70-04-C6112 on requestnight-grey S70-04-C1109 on requestpearl-grey S70-04-C80 S70-07-C80pergamon S70-04-C84 on requestPackaging unit 20/Box 20/BoxPieces per pallet 1,200 900


Foil Bagred-beige S70-04-C82 on requestsand-red structure S70-04-C32 on requestsandstone-beige S70-04-C1110 on requestsanitary grey S70-04-C18 S70-07-C18silver-green structure S70-04-C34 on requeststainless steel S70-04-C197 on requestsunset S70-04-C26 on requestthistle-grey structure S70-04-C111 on requesttransparent S70-04-C00 S70-07-C00white S70-04-C01 S70-07-C01

Packaging unit 20/Box 20/BoxPieces per pallet 1,200 900

New

New

New

New

New

New

Serkan TURKAYRectangle

Otto Proffesional Guide for FaadeOttoseal S 70 Product InformationOttoseal S 70 Technical Data SheetOttoseal S 70 Material Safety Data SheetS 70 _Certificate_DL_Laboratories_non-staining marbel_20010305_ eS 70_eurofins_LEED Conformation_EQ 4.1_20101015_eS 70_Test report_SKZ_DIN EN ISO 291_20100414_eColour Chart

ottoseal professional guide.pdf

Documents