operator guide - panasonic global 2016/7/30 sqw0660-5 operator guide data archiver model no. lb-dh7...

Operator GuideDATA ARCHIVER

Model No. LB-DH7 series

Thank you for adopting Panasonic DATA ARCHIVER.This document describes how the administrator manages the usage of the DATA ARCHIVER.Before using this unit, read “Cautions for regulations and safety / Overview / Disclaimers” and observe the instructions in that document.The DATA ARCHIVER LB-DH7 series includes the following modules and units.

Model Name Product NumberBase Module (Model Number: LB-DH70A) LB-DH70A0GBottom Module (Model Number: LB-DF81) LB-DF81Z1GExtension Module (without the Writer Unit)

Extension Unit (Model Number: LB-XH82) and Control Unit (Model Number: LB-XC82)LB-DH82Z1G

Extension Module (with the Writer Unit)Extension Unit (Model Number: LB-XH82) and Writer Unit (Model Number: LB-XD73A)

LB-DF72A0G

until 2016/7/30

SQW0660-5

Table of contents

Introduction

Overview of functions .............................................................................................................. 4

System configuration............................................................................................................................ 6

Component names.................................................................................................................... 7

Handling a magazine and magazine drawer......................................................................... 14

Magazine............................................................................................................................................ 14

How the unit identifies a magazine .................................................................................................... 17

Magazine drawer................................................................................................................................ 18

Removing a magazine from a magazine drawer................................................................................ 20

Mounting a magazine on a magazine drawer .................................................................................... 22

Operations

Operation method ................................................................................................................... 24

Web interface operation ......................................................................................................... 25

Access to Web interface .................................................................................................................... 25

Web interface screen ......................................................................................................................... 26

Web interface menu system............................................................................................................... 27

Various Functions................................................................................................................... 54

RAID functions ................................................................................................................................... 54

Encryption of write content................................................................................................................. 56

Verify mode ........................................................................................................................................ 56

S.M.A.R.T. information....................................................................................................................... 57

Initializing and Saving/Restoring the configuration settings ............................................................... 57

Email notification ................................................................................................................................ 58

SNMP................................................................................................................................................. 59

Software update ................................................................................................................................. 60

Diagnostic .......................................................................................................................................... 61

Log functions...................................................................................................................................... 62

Magazine eject mode ......................................................................................................................... 64

2

Table of contents

Others

Troubleshooting guide........................................................................................................... 66

Connection or installation problems................................................................................................... 66

Operating problems ........................................................................................................................... 68

Errors and warnings............................................................................................................... 75

List of error codes .............................................................................................................................. 77

List of warning codes ......................................................................................................................... 80

Appendix ................................................................................................................................. 83

Countermeasures against static electricity ........................................................................................ 83

Validated products ............................................................................................................................. 83

Contacting your support service provider .......................................................................................... 83

Handling for disposal ......................................................................................................................... 83

Disclaimer .......................................................................................................................................... 83

Specifications ......................................................................................................................... 84

LB-DH7 series (common) .................................................................................................................. 84

Base Module ...................................................................................................................................... 85

Bottom Module................................................................................................................................... 86

Extension Unit.................................................................................................................................... 86

Control Unit ........................................................................................................................................ 87

Writer Unit .......................................................................................................................................... 87

Extension Module (without the Writer Unit)........................................................................................ 88

Extension Module (with the Writer Unit)............................................................................................. 88

About copyright ...................................................................................................................... 89

Glossary .................................................................................................................................. 90Index ........................................................................................................................................ 91

3

Introduction

Overview of functions

The Panasonic DATA ARCHIVER LB-DH7 series is a high-capacity storage library device using optical discs.

The basic library device system of the LB-DH7 series consists of one Base Module (LB-DH70A), one Bottom Module (LB-DF81), and one Extension Module (LB-DF72A, with the Writer Unit).The Base Module, which serves as the centerpiece of the system, is connected to other modules with the exclusive use connection cables to exchange control signals with external servers. Also designed for magazine storage, it can accommodate up to 76 magazines.In addition, the Base Module has tree built-in drives that read and write data and two SAS interface ports.

The Bottom Module has a function that takes the optical discs of magazines stored in each module in and out of drives, and a scanner that reads the RFID tags built into magazines and the 1D or 2D code labels attached to magazines.

The Extension Module (with the Writer Unit) houses the Writer Unit LB-XD73A in its Extension Unit LB-XH82.

The Magazine Unit is designed for magazine storage and can accommodate up to 76 magazines.

The Writer Unit has three built-in drives that read and write data and two SAS interface ports.It can also be connected to the Base Module and Extension Unit.

The basic system includes six drives (three in the Base Module and another three in the Extension Module with the Writer Unit). These six drives make up and work as one drive system.

The DATA ARCHIVER LB-DH7 series can increase the number of magazines stored or have multiple drive systems by adding the Extension Module (with a Writer Unit) or Extension Module (without a Writer Unit) LB-DH82.The Extension Module (without a Writer Unit) is a combination of the Extension Unit integrated with Control Unit LB-XC82.The Control Unit does not house drives. It is only has a function that connects the Base Module and Magazine Extension Unit.

Supported magazinesTwo types of magazines, those with capacity of 3.6 TB and those with a capacity of 1.2 TB, are supported. (Both values are for unformatted)Each magazine houses a built-in HF-band RFID tag. When you pull out a magazine drawer of a module, store, replace or remove a magazine, and then close the magazine drawer, the scanner performs RFID reading within the system, providing information on magazines stored in the system.

4

Introduction Overview of functions

Maximum capacity of the unitThe maximum capacity of one set in the basic system is 547.2 TB (for 152 magazines [3.6 TB], unformatted).The maximum capacity of the maximum system configuration, which consists of five Extension Modules as well as the basic system above, is 1915.2 TB (for 532 magazines [3.6 TB], unformatted).

Read/Write speedThe maximum read/write speed per drive system is 432 MB/sec (RAID 0/3.6 TB magazine).

InterfaceA Serial Attached SCSI (“SAS”) system and a control interface designed to control devices such as the changer unit are mounted as drive interfaces.In addition, DATA ARCHIVER Control Software (DA control software), which is to be installed on the server to be connected to the unit, has an SCSI host interface designed to be connected to an application.

Compatibility with 19-inch rackThe unit can be installed in a 19-inch rack with a depth of 1,000 mm (39.4z) that conforms to the EIA standard.Obtain a rack that meets the following requirements:≥ A standard 19 inch rack that conforms to EIA standards≥ A server rack (must have front and rear panel mount frames and square mounting holes) ≥ A rack that has mounting holes with universal spacing≥ A rack with a mounting hole size of at least 9.3 mm (0.4q)≥ A rack with a height of at least 16U (Base Module (LB-DH70A): 6U, Bottom Module (LB-DF81): 4U, Extension

Module (with the Writer Unit) (LB-DF72A): 6U)≥ A rack that can withstand a load exceeding the combined weight of the modules to be mounted ( 84)* A rack with a depth of at least 1000 mm (39.4q) is recommended.

≥ Install the panel mount frames so that the ones on the front and rear sides are 660 mm (26.0q) to 790 mm (31.1q) apart.

≥ Install the drawer-side’s panel mount frames so that the distance between an imaginary line formed by these frames and an imaginary line extending horizontally from the projection on the inner surface of the rack’s drawer-side door will be 55 (2.2q) to 115 mm (4.5q). (The frames can be adjusted in 3 steps at 20 mm (0.8q) intervals)

5

Introduction Overview of functions

System configurationConnect various ports of the unit to a power source and a server according to the functions to be used.In addition, install DA control software to the server to be connected to the unit. For more information on how to install, refer to the Install Guide.

≥ When adding Extension Modules (with the Writer Unit), they need to be added in increments of two. Connect two SAS cables (straight) and one SAS cable (branch) to each pair of Extension Modules to be added.Use the specified optional SAS cables.There are two types of drive interface cables (SAS cables), distinguished by the shape of their server-side connectors.

∫ Required connectionsBase Module and Bottom Module/Control Unit/Writer Unit: Uses a control interface portExternal power supply: Uses the power connectorServer: Uses a drive interface port and a control interface port

Type SFF-8088 Mini-SAS Type SFF-8644 Mini-SASHD` Straight SAS cable 2.5 m (98.4q) (LB-XA25A0G) ` Straight SAS cable 2.5 m (98.4q) (LB-XA25H0G)` Branch SAS cable 2.5 m (98.4q) (LB-XA25B0G) ` Branch SAS cable 2.5 m (98.4q) (LB-XA25J0G)` Straight SAS cable 2.0 m (78.7q) (LB-XA20A0G) ` Straight SAS cable 2.0 m (78.7q) (LB-XA20H0G)` Branch SAS cable 2.0 m (78.7q) (LB-XA20B0G) ` Branch SAS cable 2.0 m (78.7q) (LB-XA20J0G)

The unit

External power supply

Server(DA control software)

Extension Module(without the Writer

Unit)

Base Module

Extension Module(with the Writer Unit)

Bottom Module

System configuration example

Exclusive use connection cable A

Exclusive use connection cable B

DC cable (+24 V)

DC cable (+24 V/+12 V)

SAS cable (Straight)

SAS cable (Branch)

Client PC Client PC Mail Server

EmailWeb interface/SNMP

6

Introduction

Component names

Base Module (LB-DH70A)_Interface side panel

A Power button

Pressing the button causes the unit to be turned on and its LED illuminates in green.≥ When the button is pressed and held for at least 4 seconds (but

less than 10 seconds), the LED will flash fast in green and the magazine carrier unit will be stored in the Bottom Module. When it is stored completely, the LED will flash slowly in green.

≥ Although it is possible to force the unit to turn off by pressing and holding this button for at least 15 seconds, in normal circumstances, turn it off by controlling it from the server connected to the unit to prevent problems such as data loss and server shutdown. When the unit is forced to turn off, the magazine carrier unit will not be stored in the Bottom Module.

≥ The power button is not present on the drawer side.≥ Even if the unit is turned off, a part of its circuitry remain on.

B Power connectorProvides a +24 V and +12 V DC power supply.≥ Before disconnecting a power cable, confirm that LED 5 listed in

the following field F is off.

C Nameplate Describes a model number, ratings, serial number, etc.

D Control interface portConnect external servers, the Bottom Module, Control Units, and Writer Units with the supplied exclusive use connection cables.

E Drive interface port

Serves as a port for data transfer.There are two ports. (SAS1, SAS2)Connects to external servers.≥ SAS interface port (connector: SFF-8644 Mini-SASHD)

7

Introduction Component names

F LED

Indicates the operating state of the unit. (The LEDs are numbered from left to right.)` LED 1 (FAN)/LED 2 (CHANGER)/LED 3 (DRIVE)

Running: illuminates in greenStopped: no illumination

` LED 4 (INFORMATION)If the operation to store the magazine carrier unit in the Bottom Module fails when the power button is pressed and held for at least 4 seconds: illuminates in redNormal: no illumination

` LED 5 (POWER)Power-on: illuminates in greenPower-off: no illumination

G Fan ventilation holeServes as a hole for air ventilation of the unit during a fan operation.≥ The unit is equipped with three fans.≥ Care should be taken not to block the hole.

H Handle

Use this to pull out the Writer Unit component from the main unit of the Base Module.(The Base Module has a Writer Unit component. It can be removed from the main unit of the Base Module.)≥ Do not use this part for any purpose other than the above, such as

lifting this unit by holding this part.

8


Base Module_Top panel

A Top panel

Serves as the top panel of the uppermost module of the system.≥ The top panel is secured to the Base Module by four

thumbscrews and one M3 screw. To add the Extension Unit to the top of the Base Module, remove the top panel from the Base Module and then install it on the uppermost Extension Unit.

Base Module_Side panel

A Ventilation holeServes for air ventilation of the unit.≥ Care should be taken not to block the hole.

Interface side

Interface side

Interface side

9


Bottom Module (LB-DF81)_Interface side panel

A Power connector Provides a +24 V DC power supply.

B Control interface portServes as a port for a connection to the Base Module via the supplied exclusive use connection cable.

C Nameplate Describes a model number, ratings, serial number, etc.

Bottom Module_Bottom panel

A Bottom panelThe panel is fastened with four screws.Remove the panel only during installation work.Reattach the panel after the work is complete.

10


Extension Unit (LB-XH82)/Base Module_Drawer side panel

A Magazine drawer

The unit has five magazine drawers on both sides capable of storing up to 76 magazines.≥ Normally, magazine drawers are locked. To open a magazine

drawer, unlock it from the Web interface.For more information, refer to “Handling a magazine and magazine drawer” ( 14).

Extension Unit _Side panel

A Nameplate Describes a model number, serial number, etc.

B Ventilation holeServes as a hole for air ventilation of the unit.≥ Care should be taken not to block the hole.

Interface side

Interface side

11


Control Unit (LB-XC82)_Interface side panel

A Control interface portServes as a port for a connection to the Base Module via the supplied exclusive use connection cable.

B Nameplate Describes a model number, serial number, etc.

C HandleUse this part to remove the Control Unit from the Extension Unit.≥ Do not use this part for any purpose other than the above, such as


12


Writer Unit (LB-XD73A)_Interface side panel

A Power connectorProvides a +24 V and +12 V DC power supply.≥ Before disconnecting a power cable, confirm that LED 5 listed in

the following field E is off.

B Nameplate Describes a model number, ratings, serial number, etc.

C Control interface portServes as a port for a connection to the Base Module via thesupplied exclusive use connection cable.

D Drive interface port

Serves as a port for data transfer.There are two ports. (SAS1, SAS2)Connects to external servers.≥ SAS interface port (connector: SFF-8644 Mini-SASHD)

E LED

Indicates the operating state of the unit. (The LEDs are numbered from left to right.)` LED 1 (FAN)/LED 2 (CHANGER)/LED 3 (DRIVE)

Running: illuminates in greenStopped: no illumination

` LED 4 (INFORMATION)Always: off

` LED 5 (POWER)Power-on: illuminates in greenPower-off: no illumination

F Fan ventilation holeServes as a hole for air ventilation of the unit during a fan operation.≥ The unit is equipped with three fans.≥ Care should be taken not to block the hole.

G HandleUse this part to remove the Writer Unit from the Extension Unit.≥ Do not use this part for any purpose other than the above, such as


13

Introduction

Handling a magazine and magazine drawer

MagazineUse a dedicated magazine for the unit.≥ For more information about the magazines that can be used, please contact your vendor.≥ Each magazine has a capacity of 3.6 TB or 1.2 TB (unformatted).

≥ For details on environmental constraints, refer to the “Cautions for regulations and safety / Overview / Disclaimers” attached to the magazine.

≥ Do not press the portion A (see right illustration) with too much force.≥ Do not expose the magazine to water.≥ Do not drop the magazine.≥ Do not leave the magazine exposed to high temperatures and high

humidity, corrosive gas, or direct sunlight.≥ Do not disassemble the magazine.≥ Store or use the magazine in an environment without dew

condensation.≥ Do not place heavy objects on a magazine.≥ Do not stack magazines on each other.

Near the user label area of the magazine, RFID tag is embedded to identify and manage magazines.

A User label areaArea for sticking a user label.Align and stick the label in a recessed area.

B Write disable switch

Switch for preventing data from being erased or overwritten by mistake. Before loading a magazine into the unit, confirm that this write disable switch at the front of the cartridge has been set at a desired position.To enable writing: Slide the switch to the left (with no lock mark)To disable writing: Slide the switch to the right (with a lock mark)≥ Writing to a magazine can be disabled through an application. For

more information about the settings, refer to the user guide for the application.

Handling and storing a magazine

RFID tag

Do not stick a metal object or an RFID on the parts around the user label area. Writing to and reading from an embedded RFID tag may fail as a result, causing malfunction.

Write-enabled Write-disabled

14

Introduction Handling a magazine and magazine drawer

The following labels can be attached to a user label area of a magazine.` 1D or 2D code label (only one of them)` Label with a character string (for magazine management)The 1D/2D code label and the character string label can be used separately or together. However, the label should be attached in the predetermined area and not overlap each other.

The 1D/2D code label of the specifications below can scan information with the built-in scanner of the unit and display it on the web interface. ( 33)<Specifications on 1D codes>

Standard: Code39Label size: 14 mm (0.55z) (H) k 70 mm (2.75z) (W) or smaller (with margins)Maximum number of characters: 12 characters (without stop and start codes)Thin bar width: 12 mil (= 0.305 mm (0.012z)) or moreRatio of thin bars to thick bars: 1:2.75Inter-character gap: 12 mil (= 0.305 mm (0.012z)) or moreBar length: 7 mm (0.28z) or moreLeading and trailing margins: 3.05 mm (0.12z) or moreColor (recommended) Black (code), White (background)

<Specifications on 2D codes>Standard: QR code (Model 2)Label size: 14 mm (0.55z) (H) k 14 mm (0.55z) (W) or smaller (with margins)Maximum number of characters: 256 characters (alphabetic character and number), 256 byte (UTF-8)Cell size: 4 dots* or more and 0.254 mm (0.01z) or more per sideMargins in four directions: 4 cells or more (A larger size is easier to read)Color (recommended) Black (code), White (background)

* “dot” refers to the smallest printing unit of a printing device.e.g., Printing with the maximum size of 14 mm (0.55z) k14 mm (0.55z)

600 dpi printer: Printable with Version 7 or earlier (45 k 45 cells)300 dpi printer: Printable with Version 4 or earlier (33 k 33 cells)

User label

e.g.,70 mm (2.75z) or smaller

7 mm (0.28z) or more, 14 mm (0.55z) or smaller

DATA ARCHIVERe.g.,

14 mm (0.55z) or smaller

14 mm (0.55z) or smaller

15


Note≥ No system operation is affected by the absence of a user label.≥ A user label shall be attached with no wrinkles and air bubbles.≥ A glossy user label surface may be difficult to read.≥ A user label shall neither protrude out of a predetermined area nor attached in other than the predetermined

area.≥ A user label partially protruded out of the predetermined area or partially soiled shall be replaced.≥ Additional user labels shall not be attached to an existing user label at label replacement.≥ The 1D/2D code label shall be attached beside the write disable switch in the user label area.≥ The operation cannot be guaranteed if the content of the 2D code label is character other than alphanumeric

and UTF-8.≥ The read contents are send as UTF-8 code to the Web browser.

For more information about UTF-8 code which can be viewed on the Web browser, refer to the operating instructions of your Web browser.

Advice on the disposal of magazinesFormatting magazines or deleting its content using the function of an application will only change file management information, and will not erase data in DATA ARCHIVER Magazines completely. The content of RFID tags will not be erased, either. When DATA ARCHIVER Magazines are disposed of, it is recommended that they be physically destroyed.

16


How the unit identifies a magazineThe unit uses an RFID tag for magazine identification and management.The unit can scans and uses a 1D/2D code label for magazine identification and management.

17


Magazine drawerThe Base Module (LB-DH70A) and the Extension unit (LB-XH82) each can be equipped with five magazine drawers on both sides (10 drawers in total).≥ The order of the middle three drawers is exchangeable on each side.≥ The numbers L1 – L5 and R1 – R5 are assigned to the magazine drawers.

L1

L2

L3

L4

L5

R1

R2

R3

R4

R5

Left top drawer

Left middle drawers

Left bottom drawer

Right top drawer

Right middle drawers

Right bottom drawer

R5R4R3R2R1

L5L4L3L2L1

Left cross-section view

Drawer sideDrawer side

Right cross-section view

18


Each magazine drawer can store up to eight magazines (six magazines only in the bottom drawer).≥ Each magazine is assigned with a magazine number consisting of a magazine drawer number and one of the slot

numbers 1 to 8. For example, the magazine on the upper right of the L1 magazine drawer is L1-4.

≥ The bottom magazine drawers, 6 and 8, on both sides cannot have magazines attached.

1 2 3 4

5 6 7 8

Bottom magazine drawers

Magazines cannot be attached.

19


Removing a magazine from a magazine drawer1 Unlock the magazine drawer.

≥ The unit locks a magazine drawer to prevent it from being opened by mistake.To remove a magazine, unlock the magazine drawer through the Web interface as follows.` Web interface: “Manage” “Open Drawer” ( 48)

≥ When unlocking the magazine drawer has been disabled by an application, refer to the application manual, give permission to unlock the magazine drawer, and unlock the magazine drawer.

≥ Be sure to push the unlocked magazine drawer all the way in to securely lock it into position. After that, inventory is executed to acquire the magazine information and the changer unit operates.

≥ The magazine drawer cannot be unlocked manually.

2 Draw the magazine drawer.≥ Hold the handle of the magazine drawer and pull it you, and while supporting the bottom of the magazine

drawer one hand, pull it completely out.≥ Depending on the system configuration or installation location, this step must be performed with both hands

at an elevated height. Ensure that the work area is safe and be careful not to stumble over objects or fall from the area.

≥ The lower front part of the bottom magazine drawer on each side has a convex shape, so place the drawer vertically, not horizontally.

Handle

Vertically placed

Horizontally placed

Convex part

20


3 Remove a magazine from the magazine drawer.≥ Remove the magazine while pushing the white lever on the right rear of each magazine toward the arrow.≥ Do not hold the portion A to remove the magazine. Instead, hold its sides.

≥ Before drawing out the magazine drawer, make sure to unlock it. Drawing out the magazine drawer by force may cause damage to it.

≥ Do not draw out the magazine drawer too hard.≥ Do not put your hand in the unit from the opening of the magazine drawer.≥ Do not step on, hang from, or lean against the magazine drawer, or perform any other actions that result in

applying too much force on it.≥ Do not leave the magazine drawer pulled out.

≥ Do not touch any mechanical portion other than portions indicated in the instructions of the procedure. Failure to observe this instruction may cause the content of the magazine to fall out.

≥ Be sure to push the white lever when removing the magazine.≥ Do not remove the magazine by main force. Failure to observe this instruction may damage the magazine and

magazine drawer.≥ Do not place the magazine drawer and the magazine on an unstable surface.

White lever

Side

Side

21


Mounting a magazine on a magazine drawer

1 Mount a magazine on a magazine drawer.≥ Insert the magazine in the direction of the arrow with the “ ” side facing upward.≥ After inserting a magazine into a magazine drawer, confirm that it cannot be pulled out.≥ Do not hold the portion A to attach the magazine. Instead, hold its sides.

2 Mount the magazine drawer into the Base Module or the Extension Unit.≥ Insert the part with the bend on the side of the magazine drawer into the guide rails on the side of the chassis

of the Base Module or Extension Unit, and push it all the way inside until it locks. The unit does not work unless the magazine drawer is pushed to the end.

≥ Make sure that the direction of the magazine drawer is inserted correctly.≥ After the magazine drawer has been pushed in, inventory is executed to acquire the magazine information

and the changer unit operates.

Preparation≥ Attach a user label onto a magazine. ( 14)≥ Confirm that the write disable switch of the magazine is in position. ( 14)

≥ If the bottom magazine drawer on the both side is placed horizontally, it may be damaged.

Side

Side

Guide rails on the chassis side

Part with the bend on the side of the magazine drawer

22


≥ Do not carry a magazine drawer with its mounting surface down. Failure to observe this instruction may cause the magazine to drop.

≥ Do not touch any mechanical portion other than portions indicated in the instructions of the procedure. Failure to observe this instruction may cause the content of the magazine to fall out.

≥ Do not remove the magazine by main force. Failure to observe this instruction may damage the magazine and magazine drawer.

≥ Do not put your hand in the unit from the opening of the magazine drawer.≥ Do not place anything other than magazines and magazine drawers in the unit.≥ Be careful not to catch your fingers in the magazine drawer.≥ Do not slam the magazine drawer shut.

Note≥ Use a dedicated magazine.≥ A magazine drawer with eight magazines weighs approximately 3 kg (6.7 lbs) at maximum (with six magazines

weighs approximately 2.4 kg (5.3 lbs) at maximum).≥ Mount a magazine on a magazine drawer securely. Failure to follow this instruction may cause injury, magazine

damage, or the unit failure due to falling.≥ Do not load a damaged magazine into a magazine drawer.≥ Do not load a magazine into a magazine drawer in an incorrect direction to prevent damage. First check an

arrow direction. ( 22)

23

Operations

Operation method

Set the following items as required.

Operates the Web interface to set and maintain the unit. ( 25)Access the unit with the Web browser to check the state of the unit, make various RAID settings, make various settings for opening and closing the magazine drawer, and operate the magazine drawer.

The unit executes instructions sent from DA control software, which supports the SCSI commands below. DA control software must be installed to a server connected to the unit.` Drive system control: MMC command` Changer unit control: SMC commandInstall the application to either the server on which DA control software is installed or another server, and connect the application using any of the iSCSI, SAS or FC interface.The DATA ARCHIVER Manager software (optional) and storage control application are used to control the changer unit and read it from the magazine or write data onto a magazine.For information on how to use, refer to each application manual.

Operations for setting and maintaining the unit

NoteWhen settings of the unit have been changed, it is recommended that the settings be saved through the Web interface. ( 42)

Operations by an application

24

Operations

Web interface operation

Access to Web interface1 Start a Web browser and input the server's IP address which will connect to the unit in the address field.

Our recommended browser is Windows Internet Explorer 9 or later. It is also possible to use other browsers that have been confirmed to operate with the unit, including Google Chrome, Mozilla Firefox, and Windows Edge.The Web interface for the unit uses port 7080 (IPv4/IPv6 : http:// (IP address):7080*).* When using IPv6, specify port 7080 according to the notation described in RFC5952.≥ When using DHCP, check the DHCP-assigned IP address of the server connected to the unit. ( 35)≥ The Login screen opens.

2 Select the login name corresponding to the function to be used and then input the password.≥ The menu available varies depending on the login name.

Login Name Available menu

Admin “Monitor”, “Configure”, “Manage”

ServiceAll menus including the “Service” menu≥ This menu is exclusively used by your support service provider.

Note≥ The Web interface will log out automatically after 1 hour. Please note that if you close the browser without

logging out, you will need to wait for up to 1 hour before you can log in again.≥ If login fails 10 times, you will not be able to log in for 3 minutes.≥ Only the first user can log in to the Web interface.≥ If the default password has not been changed yet when you log into the Web interface after installing the unit, a

screen asking you to change the password appears. Before using the Web interface, change the password.

≥ Since “Enable SSL for Web” is disabled in the factory default settings, Web interface communication, including login password entry, will not be encrypted. If communication needs to be encrypted, select “Configure” “Network” in the Web Interface, check mark “Enable SSL for Web” to enable SSL. After setting, restart DA control software. To restart DA control software, execute “systemctl stop damain” and “systemctl start damain” on the console screen on the server connected to the unit, and then wait until the “Status” is indicated as “Ready”.

≥ The Web interface can be accessed using SSL. Enable “Enable SSL for Web” following the procedure above. To access the Web interface, enter “http:// (IP address):7080”.A self-signed certificate is used when “Enable SSL for Web” is enabled and is used for an SSL certificate.If the security certificate warning appears when you access the Web interface with SSL, install the certificate or set exceptions. For more information, refer to the user’s manual for the Web browser.

25

Operations Web interface operation

Web interface screenThe following shows the basic configuration of the Web interface screen and its display contents.

A Logout Logout button

B MenuWhen selecting a menu item (Monitor/Configure/Manage/Service), the submenus of each item are displayed.≥ When selecting a submenu, the content is displayed in C.

C Setup item detailsThe content of submenu selected in B is displayed.The items display the unit status and configuration or operations.

D Status information

The date, System Name, System Status, Changer Status, Drive Status, the last error/warning and it’s code are displayed. Selecting “More” allows you to check the history of errors and warnings.≥ The information is updated on a regular basis.≥ The information about your support service provider ( 41)

specified in the “Configure” menu is also displayed.

26


Web interface menu systemFor more information, refer to a corresponding menu page.≥ Items with no initial setting listed on the corresponding menu page are set to either null or 0.

Menu item Description Page

Monitor

Indicates the detailed information or settings of the unit. P 29

System Indicates system information concerning the unit. P 29

ChangerIndicates information concerning the changer unit of the unit.

P 30

DriveIndicates information concerning the drive system of the unit.

P 31

MagazineIndicates information concerning a magazine stored in the unit.

P 33

Network Indicates network settings. P 34

Interface Indicates the settings of the interface port. P 36

View Logs Indicates the log. P 38

S.M.A.R.T.Indicates the information about recommended replacement parts of the unit.

P 38

Serial Number Indicates the serial number of each module. P 39

DrawerIndicates the unlocking/locking status of magazine drawers.

P 39

Configure

Allows you to select each item and make various settings. P 40

System Sets basic information concerning the unit. P 40

Change Password Changes the password. P 40

Date/Time Format Sets the time and date display format. P 41

Support ContactSets your support service provider contact information.

P 41

Save/RestoreSaves or restores settings and return to the initial state.

P 42

Network Makes network settings. P 43

Interface Sets the iSCSI interface port settings. P 44

Set RAID Level Sets an RAID level. P 45

Email Notification Sets email notification. P 46

SNMP Sets SNMP. P 47

Power Supply Monitoring Changes the power supply monitoring setting. P 47

27


Menu item Description Page

Manage

Allows you to manage the unit. P 48

Open Drawer Requests magazine drawer unlock. P 48

Perform Inventory Reacquires magazine information. P 48

Shutdown Shuts down and reboots the unit. P 49

Update Software Updates the unit software. P 49

Save Log Dump Acquires log concerning the unit. P 50

Diagnostic Performs a self-diagnosis. P 50

Check Disc Condition Checks the status of discs. P 51

Replace MagazineThis moves the discs inside magazines to spare magazine housings.

P 52

ServiceMenu for maintaining the unit or the like.This menu cannot be operated because of password protection for exclusive use by your support service provider.

P 53

28


This menu allows you to check detailed information and the settings concerning the unit.

System <Monitor>Indicates system information concerning the unit.

Monitor menu

Vendor Name Indicates a vendor name of the unit.

Product Name Indicates a product number of the unit.

Software Version Indicates a version of software incorporated into the unit.

Release Date Indicates a release date of software incorporated into the unit.

Location Indicates information concerning the unit installation location.

Status

Indicates the unit status information.Ready: Normal.Not Ready: Starting up or performing a self-diagnosis.Not Usable: Not available due to trouble.

Additional InformationIndicates additional information of “Status” (only when “Status” is set to “Ready”).

Diagnostic: A self-diagnosis is being performed.Update Software: Software update is taking place.

Software Information Display

Indicates the software information.

29


Changer <Monitor>Indicates information concerning the changer unit of the unit.

* Indicates only when “Status” is set to “Ready”.

Status

Indicates the status of the changer unit in the unit.Ready: Normal.Not Ready: Starting up or performing a self-diagnosis.Not Usable: Not available due to trouble.

Additional Information

Indicates additional information of “Status”.Scanning: Inventory is being executed.Transport: A magazine is being moved.Drawer Open: The indicated magazine drawer is open.Initializing: The unit is initializing.Diagnostics: The unit is performing a self-diagnostic test.Diagnostics Error: An error has been detected by the unit’s self-diagnostic test.Unit Power OFF: The unit is turning off.-: No additional information is available.

Drawer*

Indicates authorization status for unlocking the left and right magazine drawers.Prevent By Host: Unlocking the magazine drawer is prohibited by the application.

≥ A blank state indicates that the magazine drawer can be unlocked.

Move Count Indicates the number of times of the magazine move operation.

30


Drive <Monitor>Indicates information concerning the drive system of the unit.

Status

Indicates the state of the drive system of the unit.Ready: Normal.Not Ready: Starting up or performing a self-diagnosis.Not Usable: Not available due to trouble.

Additional Information

Indicates additional information of “Status” (only when “Status” is set to “Ready”).No Disc: Discs are not in.DiscIn: Discs are in.DiscIn W Protect: Discs are in, but they are write-protected.DiscIn R/W NG: Discs are in, but a write/read error has occurred.

Medium Removal

Indicates the permission status for ejecting media from the drive system (only when “Status” is set to “Ready”).

prevented By Host: The application prohibits the ejection of the disc from the drive.

≥ The disc can be ejected if this shows blank.

Temperature Indicates an internal temperature of the drive system.

Encrypt Mode

Indicates the enable/disable setting on writing data encryption.≥ When there are no discs or if there is an unformatted disc inserted, “---” is

displayed.≥ For details, refer to “Encryption of write content” ( 56).

Verify Mode

The verify mode setting status for writing is displayed.Auto Verify: Automatically determines the records to be verified and then verifies them.All Verify: Verifies all records.

≥ For details, refer to “Verify mode” ( 56).

RAID Level

Indicates the RAID level setting. ( 54)RAID 0: RAID 0 is set.RAID 5: RAID 5 is set.RAID 6: RAID 6 is set.

≥ For details, refer to “RAID functions” ( 54).

31


Magazine Address

Indicates a magazine address currently mounted in the drive system.

A　L1　5e.g.,

Module name

Magazine drawer number R: right magazine drawer L: left magazine drawer

Slot number

32


Magazine <Monitor>Display each magazine’s information.≥ Select a magazine.≥ The information displayed for each magazine indicates the following status:

* Information on a 3.6 TB magazine is displayed in two lines: the top line indicates information on Part A (top six discs in the magazine), while the bottom line indicates information on Part B (bottom six discs in the magazine).

Vacant: Magazine not present Occupied: Magazine presentMounting: Magazine currently used in the drive system Shelter: Dead storageDisable: Unusable Unknown: Unknown

Slot Indicates the magazine number of the selected magazine.

Magazine ID Indicates magazine ID information.

Magazine Type

Indicates the magazine type.Unknown: The magazine type is unknown.Recordable 1.2TB: The magazine type is that of 1.2 TB.Recordable 3.6TB: The magazine type is that of 3.6 TB.

Product Date Indicates the date of manufacture of a magazine.

Loading Count Indicates the number of times of loading into the drive system.

Barcode Indicates the information 1D/2D code of the magazine.

Free Sector*Indicates the number of free sectors. (1 sector = 2048 bites)≥ This item is not the logical free space indicated by the file system or by an

application.≥ Unformatted magazines are indicated as “Blank”.

Write Protect*

Indicates the write-protected state.Off: Writing allowed.On[Disc]: Writing disabled by the write disable switch.On[Finalize]: Already finalized.On[Soft]: Writing disabled by an application.Unknown: The write-protected state is unknown.

Encryption* Indicates the presence or absence of data encryption.

RAID Level*Indicates the RAID level that was specified when the magazine was formatted. ( 54)

RAID 0: RAID 0 is set.RAID 5: RAID 5 is set.RAID 6: RAID 6 is set.

Format Date* Indicates the date of formatting.

Last Write Date* Indicates the date of last writing.

33


Network <Monitor>Indicates the network settings.Server connected to the unit settings that are not configured with the Web interface are also displayed.≥ To change the setting, make the selection in the following order:

“Configure” “Network” ( 43)

“SSL”

“DNS”

* The setting is indicated when “DHCP” has been set to “Off”.

Enable SSL for Web Indicates the SSL setup of the Web interface.

DNS Primary* Indicates the primary DNS address.

DNS Secondary* Indicates the secondary DNS address.

DNS Tertiary* Indicates the tertiary DNS address.

34


“LAN1”, “LAN2” (Information is indicated for all the LAN ports detected by the server connected to the unit.)

Common

Indicates the common settings for the protocol stack.

IP StackIndicates IP stack information.≥ “Unknown” indicates that no setting has been selected.

(Neither IPv4 nor IPv6 are available.)

MAC Address Indicates the MAC address.

Speed Indicates the LAN link speed.

IPv4

Indicates the settings for IPv4.≥ The settings are indicated only when “IP Stack” has been set to “IPv4” or “IPv4+6”.

DHCP Indicates the setting for DHCP.

Address*1, 2 Indicates the IPv4 address.

Netmask*1, 2 Indicates the netmask address.

Gateway*1, 2 Indicates the gateway address.

IPv6

Indicates the settings for IPv6.≥ The settings are indicated only when “IP Stack” has been set to “IPv6” or “IPv4+6”.

Stateless Auto Configuration Indicates the setting for stateless auto configuration.

DHCP Indicates the setting for DHCP.

Address(Link Local)Indicates the link local IPv6 address. A value generated from the MAC address and other information is indicated.

Address(Static Assigned)*1 Indicates the static IPv6 address.

Address(Router Discovery)Indicates the router IPv6 address.≥ When “Stateless Auto Configuration” is enabled, a value

acquired from stateless auto configuration is indicated.

Gateway*1 Indicates the gateway address.

Prefix Length*1 Indicates the setting for the IP address prefix length.

*1 The setting is indicated when “DHCP” has been set to “Off”.*2 Indicates a value acquired by DHCP when “DHCP” has been set to “On”.

35


Interface <Monitor>Indicates the settings of the interface port.Server connected to the unit settings that are not configured with the Web interface are also displayed.

“SAS”

“iSCSI Interface”≥ To change the setting, make the selection in the following order:

“Configure” “Interface” ( 44)

SpeedIndicates the connection speed settings.≥ The unit is [bps].

SAS Address Indicates the WWID (World Wide Identifier).

Port Indicates an iSCSI port.

iqn Indicates the node name.

CHAP Indicates information concerning the CHAP authentication.

Target NameIndicates the target name.The target name is indicated only when “CHAP” has been set to “Target” or “Target + Initiator”.

Initiator NameIndicates the initiator name.The initiator name is indicated only when “CHAP” has been set to “Target + Initiator”.

36


“FC”

SpeedIndicates the setting for the connection speed.≥ The unit is [bps].

WWPN Indicates the port name.

WWNN Indicates the node name.

Topology Indicates the topology.

FC-AL Loop IDIndicates the loop ID.≥ The loop ID is indicated only when “Topology” has been set to “FC-AL”.

37


View Logs <Monitor>Indicates the various logs of the unit.≥ Select or enter the item and then select the “View” button to view.

S.M.A.R.T. <Monitor>Indicates a replacement recommended component or a replacement mandatory component, if any.

Good: Normal.Warning: Useful life is about to expire. Replacement is recommended.Critical: Operation is no longer possible due to malfunction or other causes. Replacement is mandatory.

Log Type

Selects the log type to be displayed.Standard Trace: View the information history.Warning Trace: View the warning history.Error Trace: View the error history.

Total Number Of Entries Indicates the total number of entries for the selected log.

Start Entry Input the first entry to display.

Number Of The Line Input the number of entries per page to display.

HDDIndicates S.M.A.R.T. information of the HDD in the server connected to the unit.Information is indicated only for HDDs in recommended servers and HDDs in other servers that are of the same type as those in recommended servers.

Fan Indicates information for the fan.

Changer (Magazine Carrier) Indicates information for the Magazine Carrier.

Changer (Disc Carrier) Indicates information for the Disc Carrier.

Drive Indicates information for the drive system.

Power Supply Monitoring

Indicates the status items below when the optional power supply monitoring adaptor is connected and the “Power Supply Monitoring” setting in the “Configure” menu is enabled.“Power Supply Monitoring Unit”/“12V Unit”/“24V Unit”

MagazineIndicates information for magazines.≥ When “Warning” is displayed, the slot number and status of the applicable

magazine is displayed below this item.

38


Serial Number <Monitor>Indicates the serial number of each module.

Drawer <Monitor>Indicates the unlocking/locking status of magazine drawers.

39


This menu allows you to select the desired menu item and make various settings.

System <Configure>Sets basic information concerning the unit.≥ Change the settings, then select “Submit” to accept the change.

Change Password <Configure>Sets the unit administrator password.≥ Change the settings, then select “Submit” to accept the change.

Configure menu

System Name

Sets the unit’s system name.≥ Current system name is displayed on the application screen.≥ A maximum of 32 characters can be input.≥ The initial setting is “LB-DH7”.

LocationSets the information on the location of the unit.≥ A maximum of 64 characters can be input.

Barcode Scan Mode

Specify the read mode for 1D/2D code.CODE39 Only: Read CODE 39 of 1D code only.QR CODE Only: Read QR CODE of 2D code only.CODE39 + QR CODE: Both CODE 39 of 1D code and QR CODE of 2D code can be read.

≥ The read time may be longer for “CODE39 + QR CODE”.≥ The initial setting is “CODE39 Only”.

New Password

Enters a new password.≥ A password must consist of 8 to 11 characters containing at least 1 alphabetic

character (both upper-case and lower-case characters are accepted), 1 number and 1 symbol.

≥ Manages the password so that it is not forgotten.

New Password Confirmation

Re-enters the new password to confirm.

40


Date/Time Format <Configure>Sets the time and date display format.≥ Change the settings, then select “Submit” to accept the change.

Support Contact <Configure>Set your support service provider contact information.≥ Change the settings, then select “Submit” to accept the change.

12h/24h

Sets the 12-hour or 24-hour system for the time display.12h: Uses a 12-hour system for time display.24h: Uses a 24-hour system for time display.

≥ The initial setting is “12h”.

Date Format

Sets the date display format.YYYY/MM/DD: Switches to the year-month-day format.MM/DD/YYYY: Switches to the month-day-year format.DD/MM/YYYY: Switches to the day-month-year format.

≥ The initial setting is “YYYY/MM/DD”.

Support NameSets your support service provider name of the unit.≥ A maximum of 64 characters can be input.

Support PhoneSets the phone number of your support service provider of the unit.≥ A maximum of 32 characters can be input.

Support EmailSets an email address of your support service provider of the unit.≥ A maximum of 255 characters can be input.

41


Save/Restore <Configure>Saves and restores settings and initialize them to initial ones.

Restore DefaultsDiscards the unit settings and initializes them to initial ones (factory settings).≥ Selecting “Restore” will execute the operation.

Save Configuration To File

Downloads the settings to the unit.≥ Selecting “Save” will execute the operation.

Restore Configuration From File

Uploads the settings from the unit.≥ Specifies the file, then select “Restore” to execute the operation.

42


Network <Configure>Makes network settings.≥ Change the settings, then select “Submit” to accept the change.

“SSL”

Enable SSL For Web

Sets the Web Interface access using SSL.Check (enable): Use SSL. To access the Web interface, enter “https://(IP address):7080”.Uncheck (disable): SSL is not used. To access the Web interface, enter “http:// (IP address):7080”.

≥ Restart DA control software after completing the setting. To restart DA control software, execute “systemctl stop damain” and “systemctl start damain” on the console screen on the server connected to the unit, and then wait until the “Status” is indicated as “Ready”.

≥ This function is disabled in the initial setting.

43


Interface <Configure>When using the iSCSI interface as host interface, set the iSCSI interface port.≥ Change the settings, then select “Submit” to accept the change.

“COMMON”

PortSets the iSCSI port.≥ Input a decimal number from 0 to 65536.≥ The initial setting is “3260”.

iqn

Sets the node name.≥ A maximum of 223 characters can be input.≥ The initial setting is “iqn.1996-03.jp.co.panasonic.LB-DH7. (serial number of bottom

module)”.

CHAP

Sets up CHAP authentication.Off: Disables CHAP authentication.Target: Performs one-way CHAP authentication.≥ The DATA ARCHIVER as a target authenticates the initiator using “Target Name” and

“Target Secret”.Target + Initiator: Performs mutual CHAP authentication.≥ The DATA ARCHIVER as a target authenticates the initiator using “Target Name” and

“Target Secret”, and then attempts to connect to the initiator using “Initiator Name” and “Initiator Secret”.

≥ The initial setting is “Off”.

Target NameSets the target name.≥ A maximum of 223 characters can be input.≥ This item can be input when “CHAP” has been set to “Target” or “Target + Initiator”.

Target SecretDefines a CHAP Secret.≥ Input 12 to 16 characters.≥ This item can be input when “CHAP” has been set to “Target” or “Target + Initiator”.

Initiator NameSets the initiator name.≥ A maximum of 223 characters can be input.≥ This item can be input when “CHAP” has been set to “Target + Initiator”.

Initiator SecretInputs the CHAP Secret of the initiator.≥ Input 12 to 16 characters.≥ This item can be input when “CHAP” has been set to “Target + Initiator”.

44


Set RAID Level <Configure>Sets the RAID level.

Default RAID Level

Sets the RAID level. ( 54)≥ Change the settings, then select “Submit” to accept the change.

RAID 0: Sets RAID 0 level.RAID 5: Sets RAID 5 level.RAID 6: Sets RAID 6 level.

≥ The initial setting is “RAID 6”.≥ When “This setting is Locked now” is indicated, the setting cannot be changed.≥ Priority may be given to a value set via an application except the Web interface.

Reset RAID Setting

Resets an RAID level set via an application except the Web interface. (This is indicated only when a RAID level has been set)≥ Selecting “Reset” will execute the operation.≥ Once the RAID level is reset, another RAID level set through the Web interface

is used.

45


Email Notification <Configure>Makes settings for email notification.≥ SMTP is used for email notification. Note that no email receiving function is available.≥ Change the settings, then select “Submit” to accept the change.

Notify ErrorsSelects the use or non-use of an email notification at error occurrence.≥ This function is disabled in the initial setting.

Notify WarningsSelects the use or non-use of an email notification at warning occurrence.≥ This function is disabled in the initial setting.

Enable Email TestSends a test email message to the destination you set. ( 58)≥ This function is disabled in the initial setting.

To Email AddressInputs an email destination address.≥ A maximum of 256 characters can be input.

SMTP Server Address (IPv4 or IPv6)

Sets an SMTP server address.≥ Inputs an IPv4 address, IPv6 address, or fully qualified domain name (FQDN, a

maximum of 39 characters).

46


SNMP <Configure>Sets SNMP. Three targets can be set as SNMP trap destinations.≥ Change the settings, then select “Submit” to accept the change.

Power Supply Monitoring<Configure>It is possible to monitor the power supply using the optional power supply monitoring adaptor.≥ Change the settings, then select “Submit” to accept the change.

EnabledSelects the use or non-use of SNMP.≥ This function is disabled in the initial setting.≥ It is necessary to configure “Port (UDP)” if this function is enabled.

Port (UDP)

Sets a port.≥ This item becomes available after “Enabled” is check marked (SNMP is

enabled).≥ SNTP normally uses Port 161, but if is in use by another application, set the

desired port.

Target 1 - IP Address Sets the IP address and the SNMP Version of Target 1/2/3.

Target 2 - IP Address

Target 3 - IP Address

Community Name

Sets an SNMP community name.≥ The initial setting is “da-public”.

To improve security, it is recommended that the initial setting be changed according to a setting made on the SNMP manager.

≥ A maximum of 256 characters can be input.

MIB File Download MIB files.

Enable Power Supply Monitoring

Enables/disables power supply monitoring.

47


This menu allows you to manipulate the unit.

Open Drawer <Manage>Unlocks magazine drawer.≥ For more information about removing a magazine, refer to “Removing a magazine from a magazine drawer”

( 20), and about mounting a magazine, refer to “Mounting a magazine on a magazine drawer” ( 22).

Perform Inventory <Manage>Executes inventory.≥ Change the settings, then select “Scan” to scan the magazines.

Manage menu

Request Unlocks the magazine drawer selected with a check mark.

Finish

After unlocking the magazine drawer and performing the desired work (replacing magazines, etc.), close the magazine drawer, and then press this button. After that, a magazine information acquisition process (inventory) is automatically performed.

All Reacquires all magazine information.

Select Drawer Reacquires the magazine information of the specified magazine drawers.

Select SlotSpecifies a magazine number, and reacquires the information of the specified magazine.

48


Shutdown <Manage>Shuts down and restarts the unit.

Update Software <Manage>Updates the unit software. ( 60)

ShutdownShuts down the unit.≥ Terminate the application prior to this operation.

Power OnStartups the unit.≥ Perform this operation before starting up the application.

RebootRestarts the unit.≥ To avoid an impact on the application, terminate it prior to this restart operation.

Current Software Version

Indicates the current software version.

Software File

Updates the unit software.Select “Browse...”, and select a file. The message to be displayed varies depending on the language setting of the browser.≥ Select the file, then select “Update” to update the software.

Browse...

49


Save Log Dump <Manage>Download the log of the unit.(This may take up to about 5 minutes, depending on the log size.)≥ Select “Save” to save the settings.

Diagnostic <Manage>Performs a self-diagnosis. ( 61)

User Log FileDownload log files for the user.≥ For more information about log files, refer to “Log functions” ( 62).

Service Log FileDownload the log files for your support service provider.≥ Execute if there was an instruction from your support service provider

representative.

Development FileDownload the dump files your support service provider.≥ Execute if there was an instruction from your support service provider

representative.

50


Check Disc Condition<Manage>Checks the status of discs.Run this check when requested by the vendor or support service provider. Before using this menu item, stop higher-level applications.Select the module (A-G) where the magazine to be checked is located, and select the Slot No. and Part.(*It is possible to select only the magazines that can be checked.)After selecting, press “Execute” to start the check.Normally, the check will finish in 30 minutes, but depending on the condition of the magazine, it may take up to about 2 hours. To cancel, press “Cancel” during the check.It is possible to open other menu items during the check, but since the check is still in progress, some items in the “Monitor” menu may be displayed as “–”.When the check is finished, the “Download(Latest)” and “Download(All)” buttons become available. (*It is necessary to refresh the screen after pressing “Execute”.)

Download(Latest) Downloads the result file of the last check.

Download(All) Downloads the result files of up to 16 checks at once.

51


Replace Magazine<Manage>This moves the discs inside magazines to spare magazine housings.≥ Obtain a spare magazine housing and load it to the drawer in advance.

Stop higher-level applications if they are running.

Select the original magazine (the magazine to be replaced), and press “Select”. (Only the magazines shown in white cells can be selected)

Select the spare magazine housing to which the discs will be moved, and press “Select”. (Only the magazine housings shown in light-yellow cells can be selected)≥ Information about the original magazine and the spare magazine housing is displayed at the bottom of the

screen.

Press “Execute”, and then press the “OK” button on the confirmation popup window to start the replacement.≥ To change the selected items, press “Clear”. This will return you to the screen for selecting the original

magazine.

52


When the replacement has completed, “Execute successfully.” is displayed.

≥ When repeating the process, press “Clear” or select “Replace Magazine” in the left pane to display the screen for selecting the original magazine.

≥ Open the magazine drawer to remove the housing of the original magazine.≥ Once the original magazine is replaced and removed, its housing cannot be reused.

This menu is intended for the unit maintenance or the like.This menu cannot be operated because of password protection for exclusive use by your support service provider.

Service menu

53

Operations

Various Functions

RAID functionsThe unit provides RAID functions for the purpose of improving the reliability and availability.The fault tolerance for the protection of data is different when writing and reading. RAID levels for each write and read are listed in the following table.≥ With this unit, the RAID configuration of each 3.6 TB magazine consists of top and bottom sides of 6 discs (12

sides in total). The RAID configuration of each 1.2 TB magazine consists of 12 discs (12 layers). The 12 layers that make up the RAID in each magazine is called a “RAID configuration unit”.

≥ RAID 5 or 6 for write fault tolerance can be set from the application. In the factory default settings, the write operation is enabled when the number of drive failure*1 is 0 for RAID 5, the number of drive failure is 1 for RAID 6. For more information about the settings, refer to the user manual for the application.

≥ The maximum transfer rate and the RAID configuration unit capacity for writing are different depending on the RAID level settings. For the maximum transfer rate and capacity for each RAID level, refer to “Specifications” ( 84).

*1 The number of writing/reading sides in drive systems that cannot perform reading/writing due to such reasons as drive failures*4, damaged media inside magazines, the lack of space available for management information, and access to low redundancy areas.

*2 The number of writable drive failures can be set to 0 or 1 in the application.*3 The number of writable drive failures can be set to 0, 1 or 2 in the application.*4 It is not possible to write/read data to/from two sides of 3.6 TB magazines in the event of a drive failure.

RAID Level

RAID 0 RAID 5 RAID 6

Fault tolerance in write

performance

Number of drive failure = 1

Writable*2/Warning report Writable*3/

Warning reportNumber of drive failure = 2

No write/Error reportNumber of drive

failure S 3

Fault tolerance in read

performance

Number of drive failure = 1 Readable/Warning report

Number of drive failure = 2

No read/Error reportNumber of drive

failure S 3

NoteIn order to improve reliability and availability, RAID 5 or 6 is recommended.

54

Operations Various Functions

Set the RAID level for each RAID configuration unit when formatting it so that the unit can perform write/read to the RAID configuration unit based on the RAID level.≥ You can specify the RAID level to format magazine on the unit or application.

To specify the RAID level with the unit, select “Configure” “Set RAID Level” on the Web interface. ( 45)For the settings of the RAID level from the application, refer to the user manual for the application.` Even if the RAID level is specified in the unit, the RAID level settings in the application take precedence.` If a RAID level has been specified through an application, the RAID level cannot be specified on the unit.

≥ To verify the RAID level settings, select “Monitor” “Drive” “RAID Level” on the control panel or the Web interface. ( 31)

≥ When changing the application, the RAID level for formatting the RAID configuration unit should be reset so that the RAID level can be specified on the unit. Select “Configure” “Set RAID Level” “Reset RAID Setting” on the Web interface to execute. ( 45)

How to set/cancel RAID level

Note≥ Do not execute “Reset RAID Setting” except when it is required. If it is executed when it is not needed, the

RAID level that has been set by the application and the RAID level of magazine may not be the same depending on the application.

≥ Decrease of Redundancy` When the write or read performance is poor due to failure, i.e. the redundancy is decreased, prompt solution

of problems is recommended.` When you perform writing with the RAID 5 and the number of drive failure is 1, or RAID 6 and the number of

drive failure is 1 or 2, the RAID configuration unit is written in the lower redundancy status. Although you have resolved the problem, the written part of RAID configuration unit is still lower redundancy. We recommend that you copy the contents to another magazine after resolving the problem.

55


Encryption of write contentThis unit enables the encryption of the write/read contents.The data encryption can be used corresponding to Advanced Encryption Standard (AES) with a key length of 256 bits.The encryption key is available from the application. For more information, refer to the user manual for the application.

The encryption is set when formatting a RAID configuration unit.Use the encrypted RAID configuration unit with the encryption key. All data in the RAID configuration unit, including the file system information, is encrypted. If the encryption key is incorrect, the RAID configuration unit cannot be recognized in the file system.≥ When you confirm the encryption of RAID configuration unit, select “Monitor” “Magazine” on the Web interface

magazine, then select “Encryption” on the screen of the Magazine detailed information. ( 33)≥ To confirm whether the unit has been set as encrypted by the application, select “Monitor” “Drive” “Encrypt

Mode” on the control panel or the Web interface. ( 31)

Verify modeThe unit provides verification functions with Auto Verify mode and All Verify mode. The verify mode can be set from the application. For more information about the settings, refer to the application manual.≥ To verify the current settings, select “Monitor” “Drive” “Verify Mode” in the Web interface. ( 31)≥ The initial setting is “Auto Verify”.

∫ Auto Verify modeWhile keeping the write performance to ensure appropriate writing quality for storing, verify only the required data under certain conditions.

∫ All Verify modePlayback all written data to verify performance. The writing transfer rate is down to about half in the All Verify mode.

56


S.M.A.R.T. informationThe unit provides a function that diagnoses the lifetime based on the amount of use of built-in units or the characteristic values.The unit diagnoses the built-in fan in the system, changer unit, drive system, external power supply (only certain external power supply models that have been validated to work with the unit), magazines and HDD (The server’s model that is recommended by Panasonic), then generates a warning if these are approaching the end of lifetime.≥ To check the status, select “Monitor” “S.M.A.R.T.” on the Web interface. ( 38)≥ It is recommended to replace the unit or magazine for which the lifetime is almost at an end as soon as possible.≥ S.M.A.R.T. information is not perfect and the accuracy is not guaranteed. Even though S.M.A.R.T. diagnosed a

unit or magazine as normal, suddenly it may fail.

Initializing and Saving/Restoring the configuration settingsYou can save, restore, or initialize the setting items except for the “Change Password” in the “Configure” menu of Web interface from “Configure” “Save/Restore”. ( 42)≥ For the default value of each setting, refer to each description page.≥ Keep the “Change Password” because it cannot be saved, restored, and initialized.

The password can be changed from the menu below.` Web interface: “Configure” “Change Password” ( 40)Please contact your support service provider if you forget the password.

57


Email notificationThe details of the error or warning will be sent by email according to the email notification settings.The error or warning code is included in the subject and message of the email.≥ In order to send a test email to the address set in “To Email Address” ( 46) following the steps below.

` Web interface: “Configure” “Email Notification” and uncheck “Notify Errors” and “Notify Warnings”, then check “Enable Email Test”, select “Submit” ( 46).Confirm receiving the test email and, if necessary, set up “Notify Errors” and “Notify Warnings”.

The subject of the email is structured as follows.

*1 The date format is specified format/The time format is 24-hour.*2 Multiple lines will be displayed depending on the content.

The following content is included in the email message.

[E1030] [2016/09/01 10:00:00 (YMD)] [LB-DH7] [DATA ARCHIVER]

Error/Warning Code

System Name*2Error Date*1

Product Name

58


SNMPThe unit provides SNMP agent feature to manage the unit by remote monitoring.The feature supports SNMP version 1 and 2c. This enables you to acquire the information about the unit from the SNMP manager and to send the information from the unit to SNMP manager (SNMP Trap notification).≥ Specifying the settings from SNMP manager to the unit are not supported.≥ To use the SNMP feature, select “Configure” “SNMP” on the Web interface for the settings. ( 47)≥ In order to improve security, changing “Community Name” from the default “da-public” is recommended. ( 47)≥ The object IDs (OID) which respond to SNMP include IDs defined by the Standard MIB (MIB - II) and the company

extended MIB (OID:.1.3.6.1.4.1.258.120.102).≥ The standard MIB contains “System Name”, “Location” and Network settings.≥ SNMP responds to the company extended MIB with information including “System Name”, “Location”, “Support

Name”, “Support Phone”, “Support Email”, equipment usage status, and S.M.A.R.T. information.≥ Also responds with a dedicated community name based on “Community Name” for maintenance. Response is for

internal information only such as equipment usage or S.M.A.R.T. information.

∫ SNMP trapThe unit notifies an SNMP trap to the SNMP manager about the changes in the unit status, or when an error occurs or it generates a warning, or access to the magazine drawer or Web interface.The additional information included in the SNMP trap are the “Vendor Name”, “Product Name”, “Serial Number”, “Software Version”, “System Name”, “Location”, and information on each trap ID. For more information, refer to the company extended MIB file for the DATA ARCHIVER. (below)The events notify by SNMP trap are as follows.

∫ Obtain the company extended MIB file for the DATA ARCHIVERDownload the company extended MIB file by selecting “Configure” “SNMP” “MIB File” from the Web interface.≥ If the software in the unit has been updated, the company extended MIB file must be downloaded again.

Trap ID Symbol name Events

1 trapSystemStatusChange Change of system status (System Status)

2 trapChangerStatusChange Change of changer unit status (Changer Status)

3 trapDriveStatusChange Change of drive system status (Drive Status)

4 trapDrawerUnlock Magazine drawer unlocked

5 trapError Error occurred

6 trapWarning Generation of warning

7 trapWebLogin Log in to the Web interface

8 trapWebLogout Log out of the Web interface

59


Software updateTo update the unit software, select “Manage” “Update Software” on Web interface.≥ For information on how to obtain the update file, contact the vendor.≥ To avoid any impact on the application, terminate it prior to this software update.≥ The duration of updating depends on the content and it may take as long as about 20 minutes.≥ Do not turn off the unit until the update is complete.≥ After the software updating, the unit restarts automatically.≥ The Web interface will automatically log out if the software update has been performed.

60


DiagnosticThe unit provides a self-diagnostic function.The self-diagnostic function operates at predetermined times on the built-in changer unit, drive system, fans and external power supply*1, respectively.You can also execute the self-diagnostic function by selecting “Manage” “Diagnostic” on the Web interface.≥ After “Diagnostic” is completed, if each status in the right pane of the web interface is indicated as “Ready” and no

new “Last Error/Last Warning” information is displayed, no problems were detected. If a new problem is displayed, select “Monitor” “S.M.A.R.T.” to check the S.M.A.R.T. information, obtain a log file ( 62), and look at the error or warning code ( 75), and then examine the location where the problem lies.

≥ When a magazine is loaded in the drive system, “Diagnostic” cannot be executed.Check whether a magazine has not been loaded by selecting “Monitor” “Drive” “Magazine Address”. If a magazine is loaded in the drive system, use the application to eject the magazine.

≥ To avoid any impact on the application, terminate it prior to running the “Diagnostic” function.≥ The duration of “Diagnostic” depends on the condition and it may take as long as about 5 minutes.

Self-diagnostic function execution

*1 Only certain external power supply models that have been validated to work with the unit.*2 The self-diagnostic function executes about every 30 days when the power is continuously on.

There is no impact on the application as it is a background operation.

≥ During the self-diagnostic process, fans, changer unit and drive system are operated for an accurate diagnosis.≥ Please note that self-diagnostics cannot detect all anomalies.

Power on About every 30 days*2 During “Diagnostic” execution

Changer unit ± s ±

Drive system ± s ±

Fan ± ± ±

External power supply*1 ± ± ±

61


Log functionsThe unit provides a log function to check the history of errors or warnings.≥ To obtain the log, select “Manage” “Save Log Dump” on Web interface. ( 50)≥ When executing “Save Log Dump”, the following filescan be acquired.

luyymmdd.txt*1: Log file for the userlsyymmdd.zip*1: Log file for your support service provider*2

ldyymmdd.bin*1: Dump file for your support service provider*2

*1 “yymmdd” indicates the year, month, and day.*2 Send it if there was an instruction from your support service provider representative.

∫ User log files` Date/Time: Date of the log

Regardless of the “Date/Time Format” settings, the date is displayed in the YYYY/MM/DD (year/month/day) format and the time is displayed in the 24-hour format.

` Device Information: General information about the unitFor more information, refer to the following item on the Web interface.“Monitor” “System” ( 29)“Configure” “Support Contact” ( 41)

` S.M.A.R.T. Information: Various information of S.M.A.R.T.For more information, refer to the following item on the Web interface.“Monitor” “S.M.A.R.T.” ( 38)

` Error Trace: Error historyFor more information on error codes, refer to “List of error codes” ( 77).

` Warning Trace: Warning historyFor more information on warning codes, refer to “List of warning codes” ( 80).

` Standard Trace: Information historyYou can check the information below.

≥ Log in/Log out to the Web interface≥ Information on magazine transfers and magazines loaded to each drive system

62


Examples of the logsDate/Time : 2016/09/01 13:00:00 (YMD)-----------------------------------------

Device Information:-------------------Vendor Name : PanasonicProduct Name : LB-DH7Software Version : GN0.0.00Serial Number B : Ibp00025 A : Iap00025 M : Mcp00025

System Name : LB-DH7Location : Support Name : Support Phone : Support Email :

S.M.A.R.T. Information:------------------System:------------------HDD : Good

------------------Module B:------------------FAN : Good Drive : Good Magazine :L1 : Good : Empty : Good : Good | Empty : Empty : Empty : Good : R1 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L2 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R2 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L3 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R3 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L4 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R4 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L5 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R5 : Empty : -------- : Empty : -------- | -------- : Empty : -------- : Empty :

Module A:------------------FAN : Good Drive : Good Changer : Good Magazine :L1 : Good : Empty : Empty : Empty | Empty : Empty : Empty : Good : R1 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L2 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R2 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L3 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R3 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L4 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R4 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty :L5 : Empty : Empty : Empty : Empty | Empty : Empty : Empty : Empty : R5 : Empty : -------- : Empty : -------- | -------- : Empty : -------- : Empty :

Error Trace:-----------------------------------------2016/09/01 09:00:00 <[Error Code] Error message>

Warning Trace:-----------------------------------------2016/09/01 09:00:00 < [Warning Code] Warning message>

Standard Trace:-----------------------------------------2016/09/01 09:00:00 < Information message >

63


Magazine eject modeThe magazine eject mode is an auxiliary function for removing the magazines specified by the application.1 Select the module and magazine drawer from which the magazine is to be removed.

When the application sets the unit to magazine eject mode, an item titled “Eject Request” appears in the status information pane of the Web interface.≥ Select the “View” button to display the “Open Drawer” screen.

≥ The magazine drawer containing the magazine specified by the application is displayed in yellow. Press the “Detail” button to open the “Eject Request Detail” screen, which shows the list of magazines in the magazine drawer, in a separate window.

≥ The magazine specified by the application is displayed in yellow. Press the “Print” button to print out the display window.*If there is another magazine administrator, it is recommended that you save the window by operating the browser and send it to that magazine administrator as electronic data.

64


2 Remove the magazine.≥ Select the magazine drawer from which the magazine is to be removed on the “Open Drawer” screen, and

press the “Request” button. This will start unlocking the magazine drawer. After the magazine drawer is unlocked, remove the magazine, load desired magazines, and close the magazine drawer.Be sure to push the unlocked magazine drawer all the way in to securely lock it into position.

≥ Magazine drawers are unlocked one at a time. To remove and load magazines stored in more than one magazine drawer, select a magazine drawer and press the “Request” button repeatedly.

≥ After all the magazines have been removed and loaded, press the “Finish” button. Inventory will be executed automatically.

≥ It is possible to exit the magazine eject mode through the application before pressing the “Finish” button. For more information, refer to the user manual for the application.

≥ It is also possible to unlock a magazine drawer other than the one containing the magazine specified by the application and remove and load magazines in that magazine drawer.

65

Others

Troubleshooting guide

Connection or installation problems

Item Problem Cause/Solutions

± Installation problems

Unlock the magazine drawer Unlocking the magazine drawer takes a long time.

The changer mechanism in the unit is operating. This may take up to about 1 minute.)Please wait.

When unlocking the magazine drawer on the Web interface, an error is displayed and the drawer cannot be unlocked.

“W2120” is displayed. The application prohibits the ejection of the media from the drive system.)Permit ejection from the application

and try again.

“W2130” is displayed. The application prohibits the unlocking of the magazine drawer.)Permit unlocking from the application

and try again.

“W2140” is displayed. The changer mechanism is using another magazine drawer to process inventory.)Try again later.

An error or warning other than the above is displayed.

Changer unit cannot operate due to an error.)Check the error log and try the

solutions. ( 77)

Magazine is unlocked but it cannot be withdrawn.

)Turn off and on the unit, and try again.If you still cannot withdraw the magazine drawer, please contact your support service provider. ( 83)

Inserting magazine in the magazine drawer

Magazine cannot be inserted fully. )Check the insert direction is correct and try again.

)Check whether there is some material around the magazine or magazine drawer.

Magazine has been inserted but it cannot be locked (taken out easily).

Installing a magazine drawer to the unit

Magazine drawer cannot be stored.

)Check whether there is some material around the magazine drawer.

If the problem persists, please contact your support service provider. ( 83)Magazine drawer is not

recognized/cannot be locked.

66

Others Troubleshooting guide

± Installation problems

Communication between modules or devices

One of “E1060”, “E1070”, “E2030”, “E2032”, “E2033”, “E2034” is displayed, and the Web interface screen has limited functionality.

The Communication between modules or devices may not be working properly.)Check whether cables are correctly

connected to the unit. Turn off and on the unit, and try again.

If the error persists, please contact the maintenance service. ( 83)

“E1090” is displayed. The number of USB hubs connected between the unit and server exceeds the maximum limit.)Reduce the number of USB hubs that

are connected between the devices. For example, change the USB port on the server or connect the devices directly without placing USB hubs between them.

Changer operation One of “E2010”, “E2011”, “E2012” is displayed.

Changer mechanism failed to operate.)Turn off and on the unit, and try again.If the error persists, please contact the maintenance service. ( 83)

± Host interface problems

Recognition of the connection

BIOS/OS does not recognize. )Check the connecting cable and connection status.

Recognize only a drive system. )Make sure the host interface adaptor and the server supports multiple LUN, or multiple LUN are enabled.Magazine cannot be replaced.

Cannot communicate with the host server after changing the ID, IP address, etc.

)Check the network settings of the server connected to the unit and if they are correct, restart the server.


67


Operating problems


± Power supply problems

Cannot turn on the power LED 5 (POWER) is off. )Check DC is output from an external power supply. Refer to the user manual for the external power supply.

)Check if the DC cable which connects the external power supply and the unit is broken, or the DC cable is securely connected between the external power supply and the unit.When checking the cable, disconnect the external power supply.

If the problem persists, please contact your support service provider. ( 83)

When the power is on, LED 5 (POWER) is illuminated, but LED 1 is not illuminated.

68



± Magazine, 1D/2D code, RFID problems

1D/2D code The 1D/2D code for specific magazine cannot be read by Inventory.

)Make sure the 1D/2D code is attached to the magazine correctly, has no dirt, and is not coming off.

)Make sure the content of the 1D/2D code is correct. ( 15)

)Make sure the magazine is mounted correctly.

Cannot read 1D/2D code for all magazines in the unit.

)Check the log and make sure that the 1D/2D code reader is not broken.If the bar-code reader has failed, it needs to be repaired. Please contact your support service provider. ( 83)

)Turn off and on the unit.

RFID The RFID for specific magazine cannot be read by Inventory.

)Make sure the magazine is mounted correctly.

Cannot read RFID for all magazines in the unit.

)Check the log and make sure that the RFID reader/writer has not failed. If the RFID reader/writer is broken, it needs to be repaired. Please contact your support service provider. ( 83)

)Turn off and on the unit.

Inventory Inventory takes a long time. Inventory takes approximately 500 seconds per module, otherwise, approximately 580 seconds per module when 1D/2D codes are posted and all RFID can be read.

69



± Read/write problems

Reading magazine Does not read the recognized magazine.

)Check if an error has occurred.If an error has occurred, check the error code and try the solutions. ( 77)

)The new magazine is not formatted. Refer to the user manual for the application and execute format.

)Read the encrypted magazine using the appropriate encryption key from an application that supports encryption.

Writing to magazine Magazine is readable, but cannot be written.

)Check if an error has occurred.If an error has occurred, check the error code and try the solutions. ( 77)

)When the magazine is finalized, you cannot write. Use another magazine.

)Make sure the magazine’s write-protection switch is set to write-protection off.

)Make sure that the write-protection is correctly set in the application.

± Encryption problems

Encryption Cannot encrypt. )An application that supports encryption is required. If you have an application that supports encryption, refer to the user manual for the application to set the encryption.

Encrypted magazine Cannot read an encrypted magazine.

)An application that supports encryption is required. If you have an application that supports encryption, refer to the user manual for the application to check the encryption key setting.

70



± RAID problems

Don’t know the RAID level Don’t know the current RAID level for the unit.

)Check the level on the Web interface. ( 31)(Settings include those of the unit, the application, and the magazine.)Don’t know the current RAID level

for the magazine.

The RAID level has been changed

The RAID level which was set on the Web interface has been changed.

The RAID level has been set from an application.)When the application has a RAID level

setting function, set it from the application.Cannot change the RAID

levelCannot change the RAID level from the Web interface.

Cannot write to magazine with the RAID level which has been set

Cannot format the magazine with the RAID level which has been set on the Web interface.

The RAID level has been set from an application.)When the application has a RAID level

setting function, set it from the application.

Changed the RAID level of the unit, but the RAID level of the formatted magazine does not change.

The RAID level of the magazine is set to the one set at the time of formatting. The level cannot be changed afterwards.

Read/write redundancy is decreased

The message that redundancy is decreased appears when mounting the magazines, writing or reading.(Warning code: W3010/W3011/W3020)

)Check the warning code and try the solutions. ( 80)

)When the magazine redundancy is reduced, it is recommended to use another magazine.

71



± Software problems

Updating Don’t know how to obtain an update file.

)Consult the vendor.

Cannot update (error message)

“W2120” is displayed. The application prohibits the ejection of the media from the drive system.)Permit ejection from the application

and try again.

“W2040” is displayed. Magazine drawer is open.)Close the magazine drawer and try

again.

“Now can’t update software.” is displayed.

)Before starting an update, stop controlling the unit through the application and the Web interface.

)Ensure that all of the magazine drawers are closed. Close them first, and then start an update.

Cannot update in the “Eject Medium Mode” screen.(Warning code: W2150)

The application sets the magazine eject mode.

Cannot update from the Web interface.

)Obtain the update file again.)When upload has failed on the Web

browser, see “Web interface” ( 73).After updating Does not start up after the software

update.)Press the power button for at least

15 seconds to force the unit to turn off, and turn on the unit again.


72



± Other problems

Web interface Cannot access the Web interface. )When DHCP is used, check if the IP address has been acquired and it has not been updated.

)Check that HTTP is not blocked by the network settings.

)Connect the server connected to the unit directly to the PC with a crossover cable to access the Web interface. Disable the unit’s DHCP access.

Garbled characters. )Make sure the character code settings for the Web browser are “Auto” or “UTF-8”.For details of the settings, refer to the user manual for the Web browser.

Layout looks wrong, such as all sub-menus are displayed.

)Enable JavaScript.For details of the settings, refer to the user manual for the Web browser.

Cannot upload/download file on the menu below.` “Configure” “Save/Restore”` “Manage” “Update Software”` “Manage” “Save Log Dump”

)Check your Web browser settings, allow the file upload or download. For details of the settings, refer to the user manual for the Web browser.

)Check the access rights to the folders and files to be uploaded/downloaded.

Password Forgot the password for the Web interface.

Contact your support service provider. ( 83)

73



± Other problems

SNMP Trap notification is not delivered. )Check the trap notification destination address.

)Verify the SNMP settings “Community Name” and “Target 1 - IP Address/Target 2 - IP Address/Target 3 - IP Address”. ( 47)

Cannot access the unit from the SNMP manager with SNMP.

)Verify the SNMP settings “Community Name” and “Target 1 - IP Address/Target 2 - IP Address/Target 3 - IP Address”. ( 47)

)When DHCP is used, check if the IP address has not been updated.

Email notification Does not receive email.(Warning code: W1030)

)Make sure the SMTP server settings are correct.

No SMTP warning, but does not receive email.

)Make sure the Email destination is correct.

)Check the recipient has not set the rejection of all messages.

74

Others

Errors and warnings

If an error or a warning situation arises while the unit is operating, it will be indicated in the right pane of the Web interface, and an email notification (when email notification is enabled) as well as an SNMP trap notification (when SNMP trap notification is enabled) will be issued in response to the contents of the error or warning. In addition, the error or warning will be recorded in the log.≥ If a warning arises, processing in progress is interrupted depending on the contents of the warning.

Action to be taken for an error or warningIf an error or warning situation arises, check the error code or warning code in “List of error codes” ( 77) or “List of warning codes” ( 80) and take proper action in response to the error or warning. If the problem cannot be solved, turn the unit off and then back on and retry the operation. (If turning off the unit does not take place, press and hold the power button for 15 seconds or more to forcibly turn off the unit.) When the problem cannot be solved even after the above action or the unit must be repaired, contact your support service provider. ( 83)

Checking the error or warning codeAn error or warning code with the unit can be known through the following:` Web interface` Email notification` SNMP trap notification` Log

Elements of error and warning codes

≥ An error in the magazine carrier unit is displayed as an error of Base Module (LB-DH70A) regardless of the position where the error occurred.

≥ When a code that is not included in the “List of error codes” ( 77) or the “List of warning codes” ( 80) is displayed, please contact maintenance. ( 83)

E1234-A

E：Ｗ：

e,g.,

Main code

ErrorWarning

Subcode

Module name

75

Others Errors and warnings

∫ How to check errors and warnings[Web interface]Check the error or warning history on the Web interface by selecting the following items in order.“Monitor” “View Logs” “Log Type” “Error Trace”/“Warning Trace” ( 38)≥ To confirm the last error or warning, refer to “Last Error” or “Last Warning” in the status information. ( 26)

*1 Displays in the date format.*2 Displays 24-hour format regardless of the settings.*3 Multiple lines will be displayed depending on the content.

[Email notification]When an error or a warning occurs, the details of the error or warning will be sent by email according to the email notification settings.≥ For more information, refer to “Email notification” ( 58).

[SNMP Trap]The details of the error or warning will be sent by SNMP trap according to the SNMP settings.The additional information of error or warning code and its notification are included in the SNMP trap.≥ For more information, refer to “SNMP” ( 59).

2016/09/01 10:00:00 <[E1030-B] Disc Carrier connection failure>Error date*1 Error time*2 Error/Warning

codeMessage*3

Display example

Module identifier

76


List of error codes

Code Email notification

SNMP trap notification Action to be taken

E1000± ±

A fault has been detected in flash memory in the unit or the peripheral circuit.It needs to be repaired.

E1010

± ±

The internal temperature of the unit is high.)Check if the exhaust port of the fan of the unit is being clogged

with an obstacle, and if yes, remove the obstacle.)Check the log records to determine if the fan has a fault, and if

yes, it needs to be repaired.If the problem persists, please contact your support service provider. ( 83))The fan works when the unit starts up or the unit requires cooling

during operation.

E1030

± ±

An error has been detected during the software processing in the unit.)Turn off and on the unit, and try again.If it still does not operate, it needs to be repaired.E1040

E1060± ±

Failed to turn on the Extension Module.It needs to be repaired.

E1070± ±

The number of modules could not be found properly due to a malfunction of the circuit board in the Extension Module.It needs to be repaired.

E1080± ±

A self-diagnostic test has detected a malfunction in the fan inside the unit.It needs to be repaired.

E1090

± ±

The number of USB hubs connected between the unit and server exceeds the maximum limit.)Reduce the number of USB hubs that are connected between the

devices. For example, change the USB port on the server or connect the devices directly without placing USB hubs between them.

E2000

± ±

Self-diagnosis has detected an error in the changer mechanism in the changer unit or the peripheral circuit of the changer mechanism.It needs to be repaired.

E2001

E2002

E2003

E2004

E2010

E2011

E2012

E2013

E2014

E2015

E2016

77




E2020

± ±

The changer mechanism in the changer unit or the drive in the drive system has failed to operate.)Withdraw the magazine drawer to make sure the installation of

magazine is correct.)Turn the unit off and back on and retry the operation.If it still does not operate, it needs to be repaired.

E2021

E2022

E2023

E2026

E2030

± ±

Failed to communicate between modules configured in the unit, or with the changer unit or the barcode reader in the unit.)Check the connection of the exclusive use connection cables to

the modules. Turn off and on the unit, and try again.If communication failure still persists, a repair is needed.

E2031

E2032

E2033

E2034

E2035

E2036

E2100

± ±

It has been detected that the connection between one or more drives or the changer in the unit and the server is cut off.)Check the cables connected to the unit first, and then restart DA

control software to initialize the unit.To restart DA control software, execute “systemctl stop damain” and “systemctl start damain” on the console screen on the server connected to the unit, and then wait until the “Status” is indicated as “Ready”.

E3000± ±

An error has been detected in the drive in the drive system or the peripheral circuit of the drive.It needs to be repaired.

E3010

± ±

A fault has been detected in several of the drives of the drive system. There is an abnormality of the media in the magazine or a failure of the drive or peripheral circuits of the drive.)Try another magazine. If the system detects the same error, it

needs to be repaired.)For information on the conditions that cause the error, refer to

“RAID functions” ( 54).

E3011

E3012

± ±

Cannot write and read since the temperature of drive system is too high.)Check if an exhaust port of the fan at the interface side panel of

the main unit is being clogged with an obstacle, and if yes, remove the obstacle.

)Check the log records to determine if the fan has a fault, and if yes, it needs to be repaired.


78




E3013± ±

A magazine data error has been found.)Replace the magazine in question with a good one.

E3020

± ±

Magazine formatting has failed.)Check the log records to determine if the drive system or

magazine has a defect, and if yes, take proper action in accordance with the error or warning code corresponding to the detected defect.

E3030

± ±

Failed write operation of two or more drives in the drive system. There is an abnormality in the media in the magazine or a failure of the drive or peripheral circuits of the drive.)Try another magazine. If the system detects the same error, it



E3031

± ±

Failed recording due to multiple factors of the drive system and a magazine. Recording to the magazine is disabled.)Check if any problems with the drive system and the magazine

have been detected in the log. If a problem has been detected, follow the solution for the corresponding error or warning code.

E3040

± ±

Failed read operation in the drive system. There is an abnormality in the media in the magazine or a failure of the drive or peripheral circuits of the drive.)Try another magazine. If the system detects the same error, it



79


List of warning codes



W1000

○ ○

A fault has been detected in the external power supply unit. (When “Enable Power Supply Monitoring” ( 47) is disabled (default).))Replace the external power supply with reference to the manual

for the external power supply in use.≥ Values written in the “0xXX” format are the hexadecimal numbers

converted from binary numbers that denote the locations of external power supply units with faults. (Examples) 0xXX: indicates a fault in the external power supply unit in the leftmost slot of the shelf; 0x05: indicates faults in the external power supply units in the leftmost slot of the shelf and the third slot from the left side of the shelf

W1000-0

○ ○

A fault has been detected in the external power supply unit. (When “Enable Power Supply Monitoring” ( 47) is enabled.)≥ Values written in the “0xXX” format are the hexadecimal numbers

converted from binary numbers that denote the locations of external power supply units with faults. (Examples) 0xXX: indicates a fault in the external power supply unit in the leftmost slot of the shelf; 0x05: indicates faults in the external power supply units in the leftmost slot of the shelf and the third slot from the left side of the shelf

W1000-1○ ○

Communication with the power supply has failed either because the power supply monitoring adaptor is malfunctioning or because it is not connected. (When “Enable Power Supply Monitoring” ( 47) is enabled.)

W1001± ±

A fault has been detected in the fan of the unit or the peripheral circuit of the fan.It needs to be repaired.

W1010± ±

The software update has failed.)Refer “Software problems” ( 72) to take proper action.

W1030s ±

Email submission to the SMTP server has failed.)Check if the network setting for the SMTP server is correct.

W1041

± ±

Detected that the life of the HDD in the server connected to the unit is nearly at its end.)We recommend to replace the flash memory unit.≥ This warning function detects only the life of the HDD in a recommended server.

W1042± ±

The rotation speed of fan has dropped.)It is recommended that the fan and the peripheral circuit be maintained.

W1050

s s

Could not detect any magazine.)Withdraw the magazine drawer to make sure the installation of

magazine is correct. ( 20)If the problem persists, please contact your support service provider. ( 83)

W1102s s

The command for turning on or off was set while the unit was processing the previous command for turning itself on or off.)Wait until the unit turns on or off.

W1103s s

The unit cannot be turned off because the software is being updated.)Try again after the update is complete.

W1104s s

The unit cannot be turned off because the magazine eject mode is set.)Turn off the magazine eject mode on the application, and try again.

80




W1112 s s The command for a software update was set while software was being updated.

W1120s s

Self-diagnostics is re-specified during self-diagnostics.)Wait for the self-diagnostics to complete.

W2000

± ±

Performance of the changer mechanism operation in the changer unit has deteriorated.)The maintenance of the changer mechanism or peripheral circuit

is recommended.

W2001

W2003± ±

Performance of the changer unit’s circuit board has deteriorated.)The maintenance of the circuit board or peripheral circuit is

recommended.

W2010

± ±

The detected number of times of magazine loading is nearly equal to the prescribed value.)Check the number of times of magazine loading by Web

interface. We recommend copying the contents of the magazine to another magazine. ( 33) It is also possible to move the discs to a spare magazine housing by performing “Replace Magazine”. ( 52)

W2011

± ±

The verify function has detected that the writing quality is not suitable for storage.)Check the status of the magazine through the Web interface or

the S.M.A.R.T. information in the log. We recommend copying the contents of the magazine to another magazine. ( 38, 62)

W2020

± ±

In spite of a failure, the magazine move operation continued normally after a retry.)If a warning message is displayed again, draw the magazine

drawer including the magazine in question to check if all magazines have been set correctly.

W2030s s

An incompatible magazine has been set.)Take out the magazine.

W2040s s

The specified processing cannot be performed because the magazine drawer is open.)Close the magazine drawer and retry the processing.

W2050s s

Failed to communicate with the drive system.)Replacing the drive system is recommended.W2051

W2120

s s

The specified processing cannot be performed because an application inhibits the disc from being taken out of the drive system.)Retry the processing after the application allows the disc to be

taken out of the drive system.

W2130

s s

The specified processing cannot be performed because an application inhibits the magazine drawer from being unlocked.)Retry the processing after the application allows the magazine

drawer to be unlocked.

W2140s s

The changer unit is operating.)Check the changer status by Web interface and retry processing

after the status changes to “Ready”.

81




W2150s s

The specified processing cannot be performed because of the magazine eject mode set for taking out a disc specified by an application.)Turn off the magazine eject mode on the application, and try again.

W3000± ±

Detected that the life of the drive system is nearly at its end.)Replacing the drive system or peripheral circuit is recommended.

W3010

± ±

The redundancy of writing has decreased owing to a drive system fault or a media defect during RAID writing.)Check the log records to determine if there is a drive system or

magazine defect, and if yes, take proper action in accordance with the error or warning code corresponding to the defect.

W3011

± ±

When reading RAID, the read redundancy is low due to a failure of the drive system or media.)Check the log records to determine if there is a drive system or

magazine defect, and if yes, take proper action in accordance with the error or warning code corresponding to the defect.

W3020

± ±

A fault has been detected in several of the drives of the drive system. The redundancy at RAID writing or RAID reading decreases. To recover the redundancy, repair the drives.)For information on the conditions that cause the warning, refer to


W3030

± ±

One or more drives or discs in the drive system have failed to startup. Redundancy during RAID writing or RAID reading is reduced. Repairs might be required for recovery.)For information on the conditions that cause the warning, refer to


W3040± ±

Writing to the magazine is not possible because the magazine management information area has run out.)Take a copy to another magazine.

82

Others

Appendix

Countermeasures against static electricityTo prevent the unit from being damaged by static electricity, observe the following instructions.≥ For transportation or long-term storage, wrap the unit with an antistatic sheet and store it in a packing box. Do not

touch the unit directly by hand as much as possible.≥ Do not touch the metal terminal of an external connector (power supply, interface, control interface port) directly by

hand or do not put a charged material closer to the metal terminal.≥ When you plug or unplug a cable to an external connector, we recommend that you should take advanced

countermeasures against static electricity, such as wearing an earth strap or touching large metal components.≥ Do not put a cable connected to an external connector near a charged material.

Validated productsFor information on products that have been validated to work with the unit, contact the vendor.

Contacting your support service providerFor contact information of support service provider, contact the vendor.

Handling for disposal≥ Dispose of the product when it becomes no longer necessary to avoid the possibility of it falling over. Do not leave

the product in its installation location.≥ Dispose of the product according to the local regulations.≥ For more information about the disposal of magazines, refer to “Advice on the disposal of magazines” ( 16).

Disclaimer≥ Panasonic assumes no responsibility for any data loss and direct or indirect damage caused by the use,

malfunction, or any failure of the unit regardless of whether the unit is under warranty or not.≥ It is a customer’s responsibility to manage data stored in DATA ARCHIVER Magazines. Make sure to check

whether the unit operates correctly before use, and back up important data as a precaution.≥ Using a device that is not validated to work with the unit may cause performance to suffer. For information on

products that have been validated to work with the unit, contact the vendor. When a device that is not validated to work with the unit is used, be fully aware of the fact that it may cause performance to suffer.

≥ If a password is compromised, it may be misused by a third party. It is a customer’s responsibility to manage a password. Panasonic assumes no responsibility for password misuse.

83

Others

Specifications

LB-DH7 series (common)

Transfer rate 3.6 TB MagazineMaximum 432 MB/sec per drive system (RAID 0)Maximum 396 MB/sec per drive system (RAID 5)Maximum 360 MB/sec per drive system (RAID 6)Average 360 MB/sec per drive system (RAID 0)Average 330 MB/sec per drive system (RAID 5)Average 300 MB/sec per drive system (RAID 6)1.2 TB MagazineMaximum 216 MB/sec (RAID 0) Maximum 198 MB/sec (RAID 5) Maximum 180 MB/sec (RAID 6) (Recording or playback with a 1.2 TB magazine uses 12 drives (2 drive systems))

Compatible magazines 3.6 TB data archiver magazine (writable/readable) Part number: LM-BM36XB** *1

1.2 TB data archiver magazine (writable/readable) Part number: LM-BM12LB** *1

(1.2 TB DATA ARCHIVER magazines can be used only when 12 drives (2 drive systems) are mounted.)

Maximum system configuration

46U rack systemBase Module: 1 unitBottom Module: 1 unitExtension Module (with the Writer Unit): 5 unitsExtension Module (without the Writer Unit): 1 unit

Magazine drawers: 70 drawersMagazines number: 532 magazinesLogical Capacity: 1915.2 TB (Using 3.6 TB magazine, unformatted)

Number of handlers Single

Access time*2 Average access time (read): 3,300 ms

Magazine transfer time*2, 3

Loading: 110 sec (Transfer from magazine drawer to drive system)

Unloading: 110 sec (Transfer from drive system to magazine drawer)

Inventory time Typically 60 sec/magazine drawer (8 magazines, no 1D/2D codes)

Shutdown time Typically 2 minute or less

Functions Encryption: XTS-AES256 (Operates under the encryption key from the application)

RAID: RAID 0, RAID 5, RAID 6*4

S.M.A.R.T. diagnostics: Fan, drive system, changer mechanism, magazine, HDD (The server’s model that is recommended by Panasonic.)

84

Others Specifications

Environmental Constraints (Common)

Base Module

Temperature range/humidity

OperatingTemperature: 10 oC to 40 oC (50 oF to 104 oF)(Temperature gradient: 10 oC (18 oF)/h or lower)Humidity: 20 % to 80 %RH (no condensation)

TransportationTemperature: j20 oC to 60 oC (j4 oF to 140 oF)Humidity: 10 % to 90 %RH (no condensation)

Installation requirements Drawer side: 1,400 mm (56z) or more for space (for maintenance)

Interface side: 1,000 mm (40z) or more for space (for maintenance)

Tilt: 3 degrees or lower (Left-right), 2 degrees or lower (Front-back)

Part number LB-DH70A0G

Model number LB-DH70A

Number of installed drive system

3 drives

Number of magazine drawers

5 magazine drawers for left and right

Maximum number of magazines

Up to 76 (6 or 8 magazines in each magazine drawer)

Power button Push SW

Laser Wave length: 405 nm

Drive interface SAS (Serial Attached SCSI)Port: 2Connector: SFF-8644 Mini-SASHD

Control interface Control interface portPort: 9Applications: Changer control and magazine drawer open/close monitor

Dimensions (W): 447 mm (17.6z) (19-inch rack EIA), 482 mm (19.0z) (Including mounting bracket)

(H): 262 mm (10.4z), 264 mm (10.4z) (Including the projecting parts)

(D): 917 mm (36.2z) (Excluding the projecting parts), 927 mm (36.5z) (Including the projecting parts)

Mass (Weight) Approx. 40 kg (89 lbs) (Except for magazines)

Approx. 63 kg (139 lbs) (Maximum number of mounted magazines)

Power DC i24 V/i12 V (w5 %)Connector: Circular connector JN2 manufactured by JAE

Current consumption Operation: DC 12 V 6 ADC 24 V 0.1 A

85


Bottom Module

Extension Unit

Part Number LB-DF81Z1G

Model Number LB-DF81

HF band RFID module Frequency: 13.56 MHz

Standard: Conforms to ISO/IEC 14443 (Type A)

Control interface Control interface portPort: 1Applications: Changer controlExclusive use connection cable: supplied




Mass (Weight) Approx. 23 kg (51 lbs)

Power DC i24 V (w5 %)Connector: Circular connector JN2 manufactured by JAE

Current consumption Operation: DC 24 V 0.5 A

Part Number None

Model Number LB-XH82

Number of magazine drawers

5 magazine drawers for left and right

Maximum number of magazines

Up to 76 (6 or 8 magazines in each magazine drawer)




Mass (Weight) Approx. 25 kg (56 lbs) (Except for magazines)

Approx. 48 kg (106 lbs) (Maximum number of mounted magazines)

86


Control Unit

Writer Unit

Part Number None

Model Number LB-XC82

Control interface Control interface portPort: 1Applications: Magazine drawer open/close monitorExclusive use connection cable: supplied

Dimensions (W): 441 mm (17.4z)

(H): 254 mm (10.0z), 258 mm (10.2z) (Including the projecting parts on the lower portion)



Part Number None

Model Number LB-XD73A

Number of installed drive system

3 drives

Laser Wave length: 405 nm

Drive interface SAS (Serial Attached SCSI)Port: 2Connector: SFF-8644 Mini-SASHD

Control interface Control interface portPort: 1Applications: Changer control and Magazine drawer open/close monitorExclusive use connection cable: supplied

Dimensions (W): 441 mm (17.4z)

(H): 254 mm (10.0z)



Power DC i24 V/i12 V (w5 %)Connector: Circular connector JN2 manufactured by JAE

Current consumption Operation: DC 12 V 6 ADC 24 V 0.1 A

87


Extension Module (without the Writer Unit)

Extension Module (with the Writer Unit)

* 1: The logical magazine capacity with RAID configuration:≥ For the 1.2 TB magazine is RAID 0: 1.13 TB, RAID 5: 1.03 TB, RAID 6: 0.93 TB.≥ For the 3.6 TB magazine is RAID 0: 3.42 TB, RAID 5: 3.14 TB, RAID 6: 2.85 TB.The actual capacity available may become smaller depending on conditions, such as when many files havebeen recorded.

* 2: The numbers indicate average performance and are not guaranteed.* 3: Magazine transfer time varies depending on the location of a magazine in the unit.* 4: When saving important data, use RAID 5/RAID 6. RAID 0 has no data protection.

Part Number LB-DH82Z1G

Configuration Extension Unit LB-XH82 and Control Unit LB-XC82

Part Number LB-DF72A0G

Configuration Extension Unit LB-XH82 and Writer Unit LB-XD73A

88

Others

About copyright

≥ QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.≥ JavaScript is a registered trademark of Oracle Corporation and its subsidiaries and affiliates in the United States

and other countries.≥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or

trademarks of the manufacturers who developed the system or product concerned.

This product incorporates the following software:(1)the software developed independently by or for Panasonic Corporation,(2)the software owned by third party and licensed to Panasonic Corporation,(3)the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0),(4)the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.1), and/or(5)open source software other than the software licensed under the GPL V2.0 and/or LGPL V2.1.

The software categorized as (3) - (5) are distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please refer to the detailed terms and conditions thereof displayed by selecting “Monitor” “System”

“Software Information Display” from the Web interface.At least three (3) years from delivery of this product, Panasonic will give to any third party who contacts us at the contact information provided below, for a charge no more than our cost of physically performing source code distribution, a complete machine-readable copy of the corresponding source code covered under GPL V2.0, LGPL V2.1 or the other licenses with the obligation to do so, as well as the respective copyright notice thereof.Contact Information: [email protected]

89

Others

Glossary

Changer unitThe changer unit is a robot mechanism to transfer magazines from the magazine drawer to the drive system. The Bottom Module (LB-DF81) has a single built-in unit.

DriveA device used for reading data from and writing data to magazines. The Base Module (LB-DH70A) and Writer Unit (LB-XD73A) have three built-in units respectively.

Drive systemA unit for counting systems used for reading data from and writing data to magazines.Six drives (combined total of drives in one Base Module and Writer Unit or in two Writer Units) constitute one drive system.

Email notificationEmail notification is a function that sends information about errors and warnings that have occurred by email.

Exclusive use connection cableThe dedicated connection cable controls the Bottom Module, Control Unit (LB-XC82), and Writer Unit from the Base Module. It is also connected to control the Base Module from an external server.

InventoryInventory is a process in which RFIDs and 1D/2D codes are read to acquire all magazine information in a magazine drawer.

MagazineMagazine is a recording medium containing multiple discs and an RFID tag. The Base Module and the Extension Unit (LB-XH82) can mount up to 76 magazines respectively.

Magazine drawerThe magazine drawer is a drawer-style mechanism to contain the magazines. The Base Module and the Extension Unit have five magazine drawers on either side. One magazine drawer can store a maximum of eight magazines (six for some drawers).

Magazine eject modeMagazine eject mode is a mode for ejecting a magazine specified through an application. The display of the web interface will be changed so that you can see which magazine has been specified.

Mounting bracketMounting brackets are used when fixing the Base Module and Bottom Module, Extension Unit to a rack. Attach one of the two mounting brackets to the left, and the other one to the right.

Web interfaceWeb interface is one of the interfaces for making settings and performing maintenance of the unit. It is used by connecting with http or https over a network.

Write disable switchWrite disable switch is a switch built into a magazine that prevents data from being accidentally deleted or overwritten.

90

Others

Index

Application . . . . . . . . . . . . . . . . . . . . . . . . . .24, 54, 56Changer unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Error code . . . . . . . . . . . . . . . . . . . . . . . . . 26, 75, 77Extension Module. . . . . . . . . . . . . . . . . . . . . . 4, 6, 88Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 38http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 43https . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Interface side panel . . . . . . . . . . . . . . . . . . . . . . . . . 7Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 22, 48IPv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Magazine drawer . . . . . . . . . . . . . . . . . . . . . . . 11, 18MIB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47, 59Password . . . . . . . . . . . . . . . . . . . . . . . . . . .25, 40, 57Power button . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 75Power connector . . . . . . . . . . . . . . . . . . . . . 7, 10, 13QR code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15RAID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 45, 54RFID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

S.M.A.R.T.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38, 57Self-signed certificate . . . . . . . . . . . . . . . . . . . . . . . 25Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6SMTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47, 59Software update . . . . . . . . . . . . . . . . . . . . . . . 49, 60SSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 43System configuration example . . . . . . . . . . . . . . . . . 6User label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15User label area . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Warning code . . . . . . . . . . . . . . . . . . . . . . . 26, 75, 80Write disable switch. . . . . . . . . . . . . . . . . . . . . 14, 331D code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 332D code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 33

91

operator guide - panasonic global 2016/7/30 sqw0660-5 operator guide data archiver model no. lb-dh7...

Documents