7/29/2019 OHL setting

1/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department Date

A10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

Page(1) of (92)

7/29/2019 OHL setting

2/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISIONStage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED DateKRG-MOE =E1.Q5 L Bodin 2012-09-21

ABB Ref. RELAY APPROVED Date

A10680 REL 670 Prim L Bodin 2012-09-21

FUNCTION

Line data

Basic data

Line to: OHL

Line length: km

Line data: R1 + jX1 +j ohm/km

R0 + jX0 +j ohm/km

RM + jXM +j ohm/km

R1' + jX1' 0,000 +j 0,000 ohm

R0' + jX0' 0 +j 0,000 ohm

RM' + jXM' 0 +j 0 ohm

Frequency: 50Hz

Voltage level: 132kV

CT-ratio: 1200 / 5 A

CVT-ratio: 132 / 0,11 kV

3 3

Maximum load on line: A

ZLoadFw (Minimum load impedance) ohm/phase

Maximum load reverse: 0 A

ZLoadRv (Minimum load impedance) ohm/phase

Page(2) of (92)

7/29/2019 OHL setting

3/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION ANSI DESCRIPTION

BIM-BOM Binary in/out HardwareParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

BIMx X Same settings for all BIM

Operation Operation Off/On 1 1 0 1 Off 0 X

Operation Operation Off/On 1 1 0 1 On 1 XOscRelease Oscilation release limit 30 30 1 1 Hz X

OscBlock Oscillation block limit 40 40 1 1 Hz X

X

BOMx X Same setting for all BOMOperation Operation Off/On 1 1 0 1 Off 0 X

Operation Operation Off/On 1 1 0 1 On 1 X

Page(3) of (92)

7/29/2019 OHL setting

4/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Analog input HardwareParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

NAMECH1 X

CTStarPoint1 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 X

CTStarPoint1 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 XCTsec1 Rated CT secondary current 1 10 1 1 A 5

CTprim1 Rated CT primary current 3000 99999 1 1 A 1200

NAMECH2 X

CTStarPoint2 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 XCTStarPoint2 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 X

CTsec2 Rated CT secondary current 1 10 1 1 A 5

CTprim2 Rated CT primary current 3000 99999 1 1 A 1200

NAMECH3 XCTStarPoint3 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 X

CTStarPoint3 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 X

CTsec3 Rated CT secondary current 1 10 1 1 A 5

CTprim3 Rated CT primary current 3000 99999 1 1 A 1200NAMECH4 X

CTStarPoint4 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 X

CTStarPoint4 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 X

CTsec4 Rated CT secondary current 1 10 1 1 A XCTprim4 Rated CT primary current 3000 99999 1 1 A X

NAMECH5 X

CTStarPoint5 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 X

CTStarPoint5 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 XCTsec5 Rated CT secondary current 1 10 1 1 A X

CTprim5 Rated CT primary current 3000 99999 1 1 A X

NAMECH6 X

CTStarPoint6 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 FromObject -1 XCTStarPoint6 ToObject= towards protected object, FromObject= the opposite 1 1 -1 2 ToObject 1 X

CTsec6 Rated CT secondary current 1 10 1 1 A XCTprim6 Rated CT primary current 3000 99999 1 1 A X

NAMECH7 XVTsec7 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V X

VTprim7 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV 132

NAMECH8 X

VTsec8 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V XVTprim8 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV 132

NAMECH9 X

VTsec9 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V X

VTprim9 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV 132NAMECH10 X

VTsec10 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V X

TRM_6I_6U

Page(4) of (92)

7/29/2019 OHL setting

5/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Analog input HardwareParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

TRM_6I_6U

VTprim10 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV 132

NAMECH11 X

VTsec11 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V X

VTprim11 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV 132NAMECH12 X

VTsec12 Rated VT secondary voltage 110.000 999.999 0.001 0.001 V X

VTprim12 Rated VT primary voltage 400.00 2000.00 0.05 0.05 kV X

Page(5) of (92)

7/29/2019 OHL setting

6/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Parameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

StationName Station name Station name 18 0 1 Faeda Linked to Station

StationNumber Station number 0 99999 0 1 X

ObjectName Object name Object name 18 0 1 =E1.Q5 Linked to BayObjectNumber Object number 0 99999 0 1 X

UnitName Unit name Unit name 18 0 1 REL 670 Prim Linked to Relay

UnitNumber Unit number 0 99999 0 1 X

X

TERMINALID

Page(6) of (92)

7/29/2019 OHL setting

7/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Parameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Frequency Rated system frequency 50.0 60.0 50.0 10.0 Hz X

PRIMVAL

Page(7) of (92)

7/29/2019 OHL setting

8/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Parameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch1 1 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch2 2 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch3 3 XPhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch4 4 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch5 5 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch6 6 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch7 7PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch8 8 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch9 9 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch10 10 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch11 11 XPhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM40-Ch12 12 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch1 13 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch2 14 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch3 15 XPhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch4 16 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch5 17 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch6 18 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch7 19 XPhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch8 20 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch9 21 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch10 22 X

PhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch11 23 XPhaseAngleRef Reference channel for phase angle presentation 1 112 1 1 TRM41-Ch12 24 X

AISVBAS

Page(8) of (92)

7/29/2019 OHL setting

9/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

LED IndicatorsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

LEDOperation LED operation On or OFF 0 1 0 1 Off 0 X

Operation LED operation On or OFF 0 1 0 1 On 1

tRestart Defines the disturbance length 0.0 100.0 0.0 0.1 s X

tMax Maximum time for the definition of a disturbance 0.0 100.0 0.0 0.1 s X

SeqTypeLED1 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED1 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED1 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED1 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED1 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED1 LED operating sequence 0 5 1 1 LatchedReset-S 5 XX

SeqTypeLED2 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED2 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED2 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED2 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED2 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED2 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED3 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED3 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED3 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED3 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED3 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED3 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED4 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED4 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED4 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED4 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED4 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED4 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED5 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED5 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED5 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED5 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED5 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED5 LED operating sequence 0 5 1 1 LatchedReset-S 5 XX

X

LEDGEN

Page(9) of (92)

7/29/2019 OHL setting

10/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

LED IndicatorsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

LEDGEN

SeqTypeLED6 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED6 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED6 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED6 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED6 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED6 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED7 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED7 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED7 LED operating sequence 0 5 1 1 LatchedAck-F-S 2 X

SeqTypeLED7 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 XSeqTypeLED7 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED7 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED8 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED8 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED8 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED8 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED8 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED8 LED operating sequence 0 5 1 1 LatchedReset-S 5 XX

SeqTypeLED9 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED9 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED9 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED9 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED9 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED9 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED10 LED operating sequence 0 5 1 1 Follow-S 0 XSeqTypeLED10 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED10 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED10 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED10 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED10 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED11 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED11 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED11 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED11 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED11 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

Page(10) of (92)

7/29/2019 OHL setting

11/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

LED IndicatorsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

LEDGEN

SeqTypeLED11 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED12 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED12 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED12 LED operating sequence 0 5 1 1 LatchedAck-F-S 2 X

SeqTypeLED12 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED12 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED12 LED operating sequence 0 5 1 1 LatchedReset-S 5 XX

SeqTypeLED13 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED13 LED operating sequence 0 5 1 1 Follow-F 1 XSeqTypeLED13 LED operating sequence 0 5 1 1 LatchedAck-F-S 2 X

SeqTypeLED13 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED13 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED13 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

XX

X

X

SeqTypeLED14 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED14 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED14 LED operating sequence 0 5 1 1 LatchedAck-F-S 2

SeqTypeLED14 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED14 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED14 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

X

SeqTypeLED15 LED operating sequence 0 5 1 1 Follow-S 0 X

SeqTypeLED15 LED operating sequence 0 5 1 1 Follow-F 1 X

SeqTypeLED15 LED operating sequence 0 5 1 1 LatchedAck-F-S2

SeqTypeLED15 LED operating sequence 0 5 1 1 LatchedAck-S-F 3 X

SeqTypeLED15 LED operating sequence 0 5 1 1 LatchedColl-S 4 X

SeqTypeLED15 LED operating sequence 0 5 1 1 LatchedReset-S 5 X

Page(11) of (92)

7/29/2019 OHL setting

12/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Parameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

SCREENDisplayTimeout Local HMI display timeout 60 120 10 10 Min X

AutoRepeat Activation of auto-repeat (On) or not (Off) 1 1 0 1 Off 0 XAutoRepeat Activation of auto-repeat (On) or not (Off) 1 1 0 1 On 1 X

ContrastLevel Contrast level for display 0 20 -10 1 % X

SymbolFont Symbol font for Single Line Diagram 0 1 0 1 ANSI 1 X

SymbolFont Symbol font for Single Line Diagram 0 1 0 1 IEC 0 XX

X

FUNCTIONS

EvListSrtOrder Sort order of event list 0 1 0 1 Latest on top 0 XEvListSrtOrder Sort order of event list 0 1 0 1 Oldest on top 1 X

SCREEN

Page(12) of (92)

7/29/2019 OHL setting

13/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

Disturbance recorderParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation Operation Off/On 0 1 0 1 Off 0 X

Operation Operation Off/On 0 1 0 1 On 1

PreFaultRecT Pre-fault recording time 0.10 1.00 0.05 0.01 s XPostFaultRecT Post-fault recording time 0.5 10.0 0.1 0.1 s X

TimeLimit Fault recording time limit 1.0 10.0 0.5 0.1 s X

PostRetrig Post-fault retrig enabled (On) or not (Off) 0 1 0 1 Off 0 X

PostRetrig Post-fault retrig enabled (On) or not (Off) 0 1 0 1 On 1ZeroAngleRef Trip value recorder, phasor reference channel 1 30 1 1 Ch X

OpModeTest Operation mode during test mode 0 1 0 1 Off 0 X

OpModeTest Operation mode during test mode 0 1 0 1 On 1

DRPRDRE

Page(13) of (92)

7/29/2019 OHL setting

14/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:1 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTRefExtOut DFT reference for external output 0 13 0 1 InternalDFTRef 0 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh1 1 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh2 2 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh3 3 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh4 4 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh5 5 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh6 6 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh7 7 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh8 8 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh9 9 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh10 10 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh11 11 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh12 12 X

DFTRefExtOut DFT reference for external output 0 13 0 1 External DFT ref 13 X

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 XDFTReference DFT reference 0 13 0 1 External DFT ref 13 X

ConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 XNegation Negation 0 3 0 1 NegateN 1 X

Negation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % XUBase Base voltage 400.00 2000.00 0.05 0.05 kV 132

TYPE 1=Voltage, 2=Current 1 2 1 1 Ch X

Page(14) of (92)

7/29/2019 OHL setting

15/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:7 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 X

DFTReference DFT reference 0 13 0 1 External DFT ref 13 XConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 X

Negation Negation 0 3 0 1 NegateN 1 XNegation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % X

UBase Base voltage 400.00 2000.00 0.05 0.05 kV 132TYPE 1=Voltage, 2=Current 1 2 1 1 Ch 2

Page(15) of (92)

7/29/2019 OHL setting

16/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:13 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTRefExtOut DFT reference for external output 0 13 0 1 InternalDFTRef 0 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh1 1 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh2 2 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh3 3 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh4 4 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh5 5 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh6 6 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh7 7 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh8 8 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh9 9 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh10 10 XDFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh11 11 X

DFTRefExtOut DFT reference for external output 0 13 0 1 AdDFTRefCh12 12 X

DFTRefExtOut DFT reference for external output 0 13 0 1 External DFT ref 13 X

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 XDFTReference DFT reference 0 13 0 1 External DFT ref 13 X

ConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 XNegation Negation 0 3 0 1 NegateN 1 X

Negation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % XUBase Base voltage 400.00 2000.00 0.05 0.05 kV 132

TYPE 1=Voltage, 2=Current 1 2 1 1 Ch X

Page(16) of (92)

7/29/2019 OHL setting

17/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:14 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 X

DFTReference DFT reference 0 13 0 1 External DFT ref 13 XConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 X

Negation Negation 0 3 0 1 NegateN 1 XNegation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % X

UBase Base voltage 400.00 2000.00 0.05 0.05 kV 132TYPE 1=Voltage, 2=Current 1 2 1 1 Ch X

Page(17) of (92)

7/29/2019 OHL setting

18/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:16 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 X

DFTReference DFT reference 0 13 0 1 External DFT ref 13 XConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 X

Negation Negation 0 3 0 1 NegateN 1 XNegation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % X

UBase Base voltage 400.00 2000.00 0.05 0.05 kV 132TYPE 1=Voltage, 2=Current 1 2 1 1 Ch X

Page(18) of (92)

7/29/2019 OHL setting

19/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:19 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 X

DFTReference DFT reference 0 13 0 1 External DFT ref 13 XConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 X

Negation Negation 0 3 0 1 NegateN 1 XNegation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % X

UBase Base voltage 400.00 2000.00 0.05 0.05 kV 132TYPE 1=Voltage, 2=Current 1 2 1 1 Ch 2

Page(19) of (92)

7/29/2019 OHL setting

20/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

SMAI:21 Analog input pre processingParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

DFTReference DFT reference 0 13 0 1 InternalDFTRef 0 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh1 1 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh2 2 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh3 3 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh4 4 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh5 5 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh6 6 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh7 7 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh8 8 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh9 9 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh10 10 XDFTReference DFT reference 0 13 0 1 AdDFTRefCh11 11 X

DFTReference DFT reference 0 13 0 1 AdDFTRefCh12 12 X

DFTReference DFT reference 0 13 0 1 External DFT ref 13 XConnectionType Input connection type 0 1 0 1 Ph-N 0 X

ConnectionType Input connection type 0 1 0 1 Ph-Ph 1 X

Negation Negation 0 3 0 1 Off 0 X

Negation Negation 0 3 0 1 NegateN 1 XNegation Negation 0 3 0 1 Negate3Ph 2 X

Negation Negation 0 3 0 1 Negate3Ph+N 3 X

MinValFreqMeas Limit for frequency calculation in % of UBase 10 200 5 1 % X

UBase Base voltage 400.00 2000.00 0.05 0.05 kV 132TYPE 1=Voltage, 2=Current 1 2 1 1 Ch X

Page(20) of (92)

7/29/2019 OHL setting

21/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

CVMMXN U, I, P, QParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

Operation Operation Off / On 0 1 0 1 Off 0 X

Operation Operation Off / On 0 1 0 1 On 1

IBase Base setting for current level in A 3000 99999 1 1 A 1200UBase Base setting for voltage level in kV 400.00 2000.00 0.05 0.05 kV 132

SBase Base setting for power values in MVA 2080.00 200000.00 0.05 0.05 MVA X

Mode Selection of measured current and voltage 1 9 1 1 L1, L2, L3 1 X

Mode Selection of measured current and voltage 1 9 1 1 Arone 2 XMode Selection of measured current and voltage 1 9 1 1 Pos Seq 3 X

Mode Selection of measured current and voltage 1 9 1 1 L1L2 4 X

Mode Selection of measured current and voltage 1 9 1 1 L2L3 5 X

Mode Selection of measured current and voltage 1 9 1 1 L3L1 6 XMode Selection of measured current and voltage 1 9 1 1 L1 7 X

Mode Selection of measured current and voltage 1 9 1 1 L2 8 X

Mode Selection of measured current and voltage 1 9 1 1 L3 9 X

PowAmpFact Amplitude factor to scale power calculations 1.000 6.000 0.000 0.001 XPowAngComp Angle compensation for phase shift between measured I & U 0.0 180.0 -180.0 0.1 Deg X

k Low pass filter coefficient for power measurement, U and I 0.00 1.00 0.00 0.01 X

UGenZeroDb Zero point clamping in % of Ubase 5 100 1 1 % X

IGenZeroDb Zero point clamping in % of Ibase 5 100 1 1 % XUAmpComp5 Amplitude factor to calibrate voltage at 5% of Ur 0.000 10.000 -10.000 0.001 % X

UAmpComp30 Amplitude factor to calibrate voltage at 30% of Ur 0.000 10.000 -10.000 0.001 % X

UAmpComp100 Amplitude factor to calibrate voltage at 100% of Ur 0.000 10.000 -10.000 0.001 % X

IAmpComp5 Amplitude factor to calibrate current at 5% of Ir 0.000 10.000 -10.000 0.001 % XIAmpComp30 Amplitude factor to calibrate current at 30% of Ir 0.000 10.000 -10.000 0.001 % X

IAmpComp100 Amplitude factor to calibrate current at 100% of Ir 0.000 10.000 -10.000 0.001 % X

IAngComp5 Angle calibration for current at 5% of Ir 0.000 10.000 -10.000 0.001 Deg X

IAngComp30 Angle calibration for current at 30% of Ir 0.000 10.000 -10.000 0.001 Deg XIAngComp100 Angle calibration for current at 100% of Ir 0.000 10.000 -10.000 0.001 Deg X

X

XSDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XSZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

SHiHiLim High High limit (physical value) 900000000.000 10000000000.000 0.000 0.001 VA X

SHiLim High limit (physical value) 800000000.000 10000000000.000 0.000 0.001 VA X

SLowLim Low limit (physical value) 0.000 10000000000.000 0.000 0.001 VA XSLowLowLim Low Low limit (physical value) 0.000 10000000000.000 0.000 0.001 VA X

SMin Minimum value 0.000 10000000000.000 0.000 0.001 VA X

SMax Maximum value 1000000000.000 10000000000.000 0.000 0.001 VA X

SRepTyp Reporting type 0 2 0 1 Cyclic 0 XSRepTyp Reporting type 0 2 0 1 Dead band 1 X

SRepTyp Reporting type 0 2 0 1 Int deadband 2 X

Page(21) of (92)

7/29/2019 OHL setting

22/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

CVMMXN U, I, P, QParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

SLimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

PDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

PZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

PHiHiLim High High limit (physical value) 900000000.000 10000000000.000 -10000000000.000 0.001 W XPHiLim High limit (physical value) 800000000.000 10000000000.000 -10000000000.000 0.001 W X

PLowLim Low limit (physical value) -800000000.000 10000000000.000 -10000000000.000 0.001 W X

PLowLowLim Low Low limit (physical value) -900000000.000 10000000000.000 -10000000000.000 0.001 W X

PMin Minimum value -1000000000.000 10000000000.000 -10000000000.000 0.001 W XPMax Maximum value 1000000000.000 10000000000.000 -10000000000.000 0.001 W X

PRepTyp Reporting type 0 2 0 1 Cyclic 0 X

PRepTyp Reporting type 0 2 0 1 Dead band 1 XPRepTyp Reporting type 0 2 0 1 Int deadband 2 XPLimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

X

QDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

QZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% XQHiHiLim High High limit (physical value) 900000000.000 10000000000.000 -10000000000.000 0.001 VAr X

QHiLim High limit (physical value) 800000000.000 10000000000.000 -10000000000.000 0.001 VAr X

QLowLim Low limit (physical value) -800000000.000 10000000000.000 -10000000000.000 0.001 VAr X

QLowLowLim Low Low limit (physical value) -900000000.000 10000000000.000 -10000000000.000 0.001 VAr XQMin Minimum value -1000000000.000 10000000000.000 -10000000000.000 0.001 VAr X

QMax Maximum value 1000000000.000 10000000000.000 -10000000000.000 0.001 VAr X

QRepTyp Reporting type 0 2 0 1 Cyclic 0 X

QRepTyp Reporting type 0 2 0 1 Dead band 1 XQRepTyp Reporting type 0 2 0 1 Int deadband 2 X

QLimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

X

PFDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XPFZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

PFHiHiLim High High limit (physical value) 3.000 3.000 -3.000 0.001 XPFHiLim High limit (physical value) 2.000 3.000 -3.000 0.001 X

PFLowLim Low limit (physical value) -2.000 3.000 -3.000 0.001 XPFLowLowLim Low Low limit (physical value) -3.000 3.000 -3.000 0.001 X

PFMin Minimum value -1.000 0.000 -1.000 0.001 X

PFMax Maximum value 1.000 1.000 0.000 0.001 X

PFRepTyp Reporting type 0 2 0 1 Cyclic 0 XPFRepTyp Reporting type 0 2 0 1 Dead band 1 X

PFRepTyp Reporting type 0 2 0 1 Int deadband 2 X

PFLimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

X

Page(22) of (92)

7/29/2019 OHL setting

23/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

CVMMXN U, I, P, QParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

UDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

UZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UHiHiLim High High limit (physical value) 460000.000 10000000000.000 -10000000000.000 0.001 V X

UHiLim High limit (physical value) 450000.000 10000000000.000 -10000000000.000 0.001 V XULowLim Low limit (physical value) 380000.000 10000000000.000 -10000000000.000 0.001 V X

ULowLowLim Low Low limit (physical value) 350000.000 10000000000.000 -10000000000.000 0.001 V X

UMin Minimum value 0.000 10000000000.000 -10000000000.000 0.001 V X

UMax Maximum value 400000.000 10000000000.000 -10000000000.000 0.001 V XURepTyp Reporting type 0 2 0 1 Cyclic 0 X

URepTyp Reporting type 0 2 0 1 Dead band 1 X

URepTyp Reporting type 0 2 0 1 Int deadband 2 XULimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

X

IDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

IZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

IHiHiLim High High limit (physical value) 900.000 10000000000.000 -10000000000.000 0.001 A XIHiLim High limit (physical value) 800.000 10000000000.000 -10000000000.000 0.001 A X

ILowLim Low limit (physical value) -800.000 10000000000.000 -10000000000.000 0.001 A X

ILowLowLim Low Low limit (physical value) -900.000 10000000000.000 -10000000000.000 0.001 A X

IMin Minimum value 0.000 10000000000.000 -10000000000.000 0.001 A XIMax Maximum value 1000.000 10000000000.000 -10000000000.000 0.001 A X

IRepTyp Reporting type 0 2 0 1 Cyclic 0 X

IRepTyp Reporting type 0 2 0 1 Dead band 1 X

IRepTyp Reporting type 0 2 0 1 Int deadband 2 XILimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

X

FrDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

FrZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% XFrHiHiLim High High limit (physical value) 65.000 10000000000.000 -10000000000.000 0.001 Hz X

FrHiLim High limit (physical value) 63.000 10000000000.000 -10000000000.000 0.001 Hz XFrLowLim Low limit (physical value) 47.000 10000000000.000 -10000000000.000 0.001 Hz X

FrLowLowLim Low Low limit (physical value) 45.000 10000000000.000 -10000000000.000 0.001 Hz XFrMin Minimum value 0.000 10000000000.000 -10000000000.000 0.001 Hz X

FrMax Maximum value 70.000 10000000000.000 -10000000000.000 0.001 Hz X

FrRepTyp Reporting type 0 2 0 1 Cyclic 0 X

FrRepTyp Reporting type 0 2 0 1 Dead band 1 XFrRepTyp Reporting type 0 2 0 1 Int deadband 2 X

FrLimHyst Hysteresis value in % of range (common for all limits) 5.000 100.000 0.000 0.001 % X

Page(23) of (92)

7/29/2019 OHL setting

24/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

CMMXU Phase currentsParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

Operation Operation Mode On / Off 0 1 0 1 Off 0 X

Operation Operation Mode On / Off 0 1 0 1 On 1

IBase Base setting for current level in A 3000 99999 1 1 A 1200IAmpComp5 Amplitude factor to calibrate current at 5% of Ir 0.000 10.000 -10.000 0.001 % X

IAmpComp30 Amplitude factor to calibrate current at 30% of Ir 0.000 10.000 -10.000 0.001 % X

IAmpComp100 Amplitude factor to calibrate current at 100% of Ir 0.000 10.000 -10.000 0.001 % X

IAngComp5 Angle calibration for current at 5% of Ir 0.000 10.000 -10.000 0.001 Deg XIAngComp30 Angle calibration for current at 30% of Ir 0.000 10.000 -10.000 0.001 Deg X

IAngComp100 Angle calibration for current at 100% of Ir 0.000 10.000 -10.000 0.001 Deg X

X

XIL1DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

IL1ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

IL1HiHiLim High High limit (physical value) 900.000 10000000000.000 0.000 0.001 A X

IL1HiLim High limit (physical value) 800.000 10000000000.000 0.000 0.001 A XIL1LowLim Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A X

IL1LowLowLim Low Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A X

IL1Min Minimum value 0.000 10000000000.000 0.000 0.001 A X

IL1Max Maximum value 1000.000 10000000000.000 0.000 0.001 A XIL1RepTyp Reporting type 0 2 0 1 Cyclic 0 X

IL1RepTyp Reporting type 0 2 0 1 Dead band 1 X

IL1RepTyp Reporting type 0 2 0 1 Int deadband 2 X

IL1LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % XIL1AngDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

X

X

IL2DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XIL2ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

IL2HiHiLim High High limit (physical value) 900.000 10000000000.000 0.000 0.001 A X

IL2HiLim High limit (physical value) 800.000 10000000000.000 0.000 0.001 A XIL2LowLim Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A XIL2LowLowLim Low Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A X

IL2Min Minimum value 0.000 10000000000.000 0.000 0.001 A X

IL2Max Maximum value 1000.000 10000000000.000 0.000 0.001 A X

IL2RepTyp Reporting type 0 2 0 1 Cyclic 0 XIL2RepTyp Reporting type 0 2 0 1 Dead band 1 X

IL2RepTyp Reporting type 0 2 0 1 Int deadband 2 X

IL2LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % X

IL2AngDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

Page(24) of (92)

7/29/2019 OHL setting

25/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

CMMXU Phase currentsParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

IL3DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

IL3ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

IL3HiHiLim High High limit (physical value) 900.000 10000000000.000 0.000 0.001 A X

IL3HiLim High limit (physical value) 800.000 10000000000.000 0.000 0.001 A XIL3LowLim Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A X

IL3LowLowLim Low Low limit (physical value) 0.000 10000000000.000 0.000 0.001 A X

IL3Min Minimum value 0.000 10000000000.000 0.000 0.001 A X

IL3Max Maximum value 1000.000 10000000000.000 0.000 0.001 A XIL3RepTyp Reporting type 0 2 0 1 Cyclic 0 X

IL3RepTyp Reporting type 0 2 0 1 Dead band 1 X

IL3RepTyp Reporting type 0 2 0 1 Int deadband 2 XIL3LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % XIL3AngDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

Page(25) of (92)

7/29/2019 OHL setting

26/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

VMMXU U-U voltageParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

Operation Operation Mode On / Off 0 1 0 1 Off 0 X

Operation Operation Mode On / Off 0 1 0 1 On 1

UBase Base setting for voltage level in kV 400.00 2000.00 0.05 0.05 kV 132UAmpComp100 Amplitude factor to calibrate voltage at 100% of Ur 0.000 10.000 -10.000 0.001 % X

X

X

UL12DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XUL12ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UL12HiHiLim High High limit (physical value) 450000.000 10000000000.000 0.000 0.001 V X

UL12HiLim High limit (physical value) 420000.000 10000000000.000 0.000 0.001 V X

UL12LowLim Low limit (physical value) 380000.000 10000000000.000 0.000 0.001 V XUL12LowLowLim Low Low limit (physical value) 350000.000 10000000000.000 0.000 0.001 V X

UL12Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL12Max Maximum value 500000.000 10000000000.000 0.000 0.001 V X

UL12RepTyp Reporting type 0 2 0 1 Cyclic 0 XUL12RepTyp Reporting type 0 2 0 1 Dead band 1 X

UL12RepTyp Reporting type 0 2 0 1 Int deadband 2 X

UL12LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % X

XUL12AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

X

X

UL23DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XUL23ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UL23HiHiLim High High limit (physical value) 450000.000 10000000000.000 0.000 0.001 V X

UL23HiLim High limit (physical value) 420000.000 10000000000.000 0.000 0.001 V X

UL23LowLim Low limit (physical value) 380000.000 10000000000.000 0.000 0.001 V XUL23LowLowLim Low Low limit (physical value) 350000.000 10000000000.000 0.000 0.001 V X

UL23Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL23Max Maximum value 500000.000 10000000000.000 0.000 0.001 V XUL23RepTyp Reporting type 0 2 0 1 Cyclic 0 XUL23RepTyp Reporting type 0 2 0 1 Dead band 1 X

UL23RepTyp Reporting type 0 2 0 1 Int deadband 2 X

UL23LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % X

XUL23AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

X

X

XX

X

Page(26) of (92)

7/29/2019 OHL setting

27/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

VMMXU U-U voltageParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

UL31DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

UL31ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UL31HiHiLim High High limit (physical value) 450000.000 10000000000.000 0.000 0.001 V X

UL31HiLim High limit (physical value) 420000.000 10000000000.000 0.000 0.001 V XUL31LowLim Low limit (physical value) 380000.000 10000000000.000 0.000 0.001 V X

UL31LowLowLim Low Low limit (physical value) 350000.000 10000000000.000 0.000 0.001 V X

UL31Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL31Max Maximum value 500000.000 10000000000.000 0.000 0.001 V XUL31RepTyp Reporting type 0 2 0 1 Cyclic 0 X

UL31RepTyp Reporting type 0 2 0 1 Dead band 1 X

UL31RepTyp Reporting type 0 2 0 1 Int deadband 2 XUL31LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % XX

UL31AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

Page(27) of (92)

7/29/2019 OHL setting

28/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

VNMMXU U-N voltageParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

Operation Operation Mode On / Off 0 1 0 1 Off 0 X

Operation Operation Mode On / Off 0 1 0 1 On 1

UBase Base setting for voltage level in kV 400.00 2000.00 0.05 0.05 kV 132UAmpComp100 Amplitude factor to calibrate voltage at 100% of Ur 0.000 10.000 -10.000 0.001 % X

X

X

UL1DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XUL1ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UL1HiHiLim High High limit (physical value) 260000.000 10000000000.000 0.000 0.001 V X

UL1HiLim High limit (physical value) 240000.000 10000000000.000 0.000 0.001 V X

UL1LowLim Low limit (physical value) 220000.000 10000000000.000 0.000 0.001 V XUL1LowLowLim Low Low limit (physical value) 200000.000 10000000000.000 0.000 0.001 V X

UL1Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL1Max Maximum value 300000.000 10000000000.000 0.000 0.001 V X

UL1RepTyp Reporting type 0 2 0 1 Cyclic 0 XUL1RepTyp Reporting type 0 2 0 1 Dead band 1 X

UL1RepTyp Reporting type 0 2 0 1 Int deadband 2 X

UL1LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % X

UL1AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type XX

X

UL2DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

UL2ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% XUL2HiHiLim High High limit (physical value) 260000.000 10000000000.000 0.000 0.001 V X

UL2HiLim High limit (physical value) 240000.000 10000000000.000 0.000 0.001 V X

UL2LowLim Low limit (physical value) 220000.000 10000000000.000 0.000 0.001 V X

UL2LowLowLim Low Low limit (physical value) 200000.000 10000000000.000 0.000 0.001 V XUL2Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL2Max Maximum value 300000.000 10000000000.000 0.000 0.001 V X

UL2RepTyp Reporting type 0 2 0 1 Cyclic 0 XUL2RepTyp Reporting type 0 2 0 1 Dead band 1 XUL2RepTyp Reporting type 0 2 0 1 Int deadband 2 X

UL2LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % X

UL2AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

XX

X

X

X

Page(28) of (92)

7/29/2019 OHL setting

29/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION DESCRIPTION

VNMMXU U-N voltageParameter name Parameter desc Default value Max Min Step Enum Enum value Default Comment

UL3DbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

UL3ZeroDb Zero point clamping in 0,001% of range 0 100000 0 1 m% X

UL3HiHiLim High High limit (physical value) 260000.000 10000000000.000 0.000 0.001 V X

UL3HiLim High limit (physical value) 240000.000 10000000000.000 0.000 0.001 V XUL3LowLim Low limit (physical value) 220000.000 10000000000.000 0.000 0.001 V X

UL3LowLowLim Low Low limit (physical value) 200000.000 10000000000.000 0.000 0.001 V X

UL3Min Minimum value 0.000 10000000000.000 0.000 0.001 V X

UL3Max Maximum value 300000.000 10000000000.000 0.000 0.001 V XUL3RepTyp Reporting type 0 2 0 1 Cyclic 0 X

UL3RepTyp Reporting type 0 2 0 1 Dead band 1 X

UL3RepTyp Reporting type 0 2 0 1 Int deadband 2 XUL3LimHys Hysteresis value in % of range and is common for all limits 5.000 100.000 0.000 0.001 % XUL3AnDbRepInt Cycl: Report interval (s), Db: In % of range, Int Db: In %s 10 300 1 1 Type X

Page(29) of (92)

7/29/2019 OHL setting

30/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation01 Trigger operation On/Off 0 1 0 1 Off 0 X

Operation01 Trigger operation On/Off 0 1 0 1 On 1

TrigLevel01 Trig on positiv (1) or negative (0) slope for binary inp 1 1 1 0 1 Trig on 0 0 XTrigLevel01 Trig on positiv (1) or negative (0) slope for binary inp 1 1 1 0 1 Trig on 1 1 X

IndicationMa01 Indication mask for binary channel 1 0 1 0 1 Hide 0 X

IndicationMa01 Indication mask for binary channel 1 0 1 0 1 Show 1

SetLED01 Set red-LED on HMI for binary channel 1 0 1 0 1 Off 0 XSetLED01 Set red-LED on HMI for binary channel 1 0 1 0 1 On 1

Operation02 Trigger operation On/Off 0 1 0 1 Off 0 X

Operation02 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel02 Trig on positiv (1) or negative (0) slope for binary inp 2 1 1 0 1 Trig on 0 0 XTrigLevel02 Trig on positiv (1) or negative (0) slope for binary inp 2 1 1 0 1 Trig on 1 1 X

IndicationMa02 Indication mask for binary channel 2 0 1 0 1 Hide 0 X

IndicationMa02 Indication mask for binary channel 2 0 1 0 1 Show 1 X

SetLED02 Set red-LED on HMI for binary channel 2 0 1 0 1 Off 0 XSetLED02 Set red-LED on HMI for binary channel 2 0 1 0 1 On 1 X

Operation03 Trigger operation On/Off 0 1 0 1 Off 0 X

Operation03 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel03 Trig on positiv (1) or negative (0) slope for binary inp 3 1 1 0 1 Trig on 0 0 XTrigLevel03 Trig on positiv (1) or negative (0) slope for binary inp 3 1 1 0 1 Trig on 1 1 X

IndicationMa03 Indication mask for binary channel 3 0 1 0 1 Hide 0 X

IndicationMa03 Indication mask for binary channel 3 0 1 0 1 Show 1 X

SetLED03 Set red-LED on HMI for binary channel 3 0 1 0 1 Off 0 XSetLED03 Set red-LED on HMI for binary channel 3 0 1 0 1 On 1 X

Operation04 Trigger operation On/Off 0 1 0 1 Off 0 X

Operation04 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel04 Trig on positiv (1) or negative (0) slope for binary inp 4 1 1 0 1 Trig on 0 0 XTrigLevel04 Trig on positiv (1) or negative (0) slope for binary inp 4 1 1 0 1 Trig on 1 1 X

IndicationMa04 Indication mask for binary channel 4 0 1 0 1 Hide 0 X

IndicationMa04 Indication mask for binary channel 4 0 1 0 1 Show 1 XSetLED04 Set red-LED on HMI for binary channel 4 0 1 0 1 Off 0 XSetLED04 Set red-LED on HMI for binary channel 4 0 1 0 1 On 1 X

Operation05 Trigger operation On/Off 0 1 0 1 Off 0 X

Operation05 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel05 Trig on positiv (1) or negative (0) slope for binary inp 5 1 1 0 1 Trig on 0 0 XTrigLevel05 Trig on positiv (1) or negative (0) slope for binary inp 5 1 1 0 1 Trig on 1 1 X

IndicationMa05 Indication mask for binary channel 5 0 1 0 1 Hide 0 X

IndicationMa05 Indication mask for binary channel 5 0 1 0 1 Show 1 X

SetLED05 Set red-LED on HMI for binary channel 5 0 1 0 1 Off 0 XSetLED05 Set red-LED on HMI for binary channel 5 0 1 0 1 On 1 X

Operation06 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(30) of (92)

7/29/2019 OHL setting

31/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation06 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel06 Trig on positiv (1) or negative (0) slope for binary inp 6 1 1 0 1 Trig on 0 0 X

TrigLevel06 Trig on positiv (1) or negative (0) slope for binary inp 6 1 1 0 1 Trig on 1 1 X

IndicationMa06 Indication mask for binary channel 6 0 1 0 1 Hide 0 XIndicationMa06 Indication mask for binary channel 6 0 1 0 1 Show 1 X

SetLED06 Set red-LED on HMI for binary channel 6 0 1 0 1 Off 0 X

SetLED06 Set red-LED on HMI for binary channel 6 0 1 0 1 On 1 X

Operation07 Trigger operation On/Off 0 1 0 1 Off 0 XOperation07 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel07 Trig on positiv (1) or negative (0) slope for binary inp 7 1 1 0 1 Trig on 0 0 X

TrigLevel07 Trig on positiv (1) or negative (0) slope for binary inp 7 1 1 0 1 Trig on 1 1 XIndicationMa07 Indication mask for binary channel 7 0 1 0 1 Hide 0 XIndicationMa07 Indication mask for binary channel 7 0 1 0 1 Show 1

SetLED07 Set red-LED on HMI for binary channel 7 0 1 0 1 Off 0 X

SetLED07 Set red-LED on HMI for binary channel 7 0 1 0 1 On 1 X

Operation08 Trigger operation On/Off 0 1 0 1 Off 0 XOperation08 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel08 Trig on positiv (1) or negative (0) slope for binary inp 8 1 1 0 1 Trig on 0 0 X

TrigLevel08 Trig on positiv (1) or negative (0) slope for binary inp 8 1 1 0 1 Trig on 1 1 X

IndicationMa08 Indication mask for binary channel 8 0 1 0 1 Hide 0 XIndicationMa08 Indication mask for binary channel 8 0 1 0 1 Show 1

SetLED08 Set red-LED on HMI for binary channel 8 0 1 0 1 Off 0 X

SetLED08 Set red-LED on HMI for binary channel 8 0 1 0 1 On 1 X

Operation09 Trigger operation On/Off 0 1 0 1 Off 0 XOperation09 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel09 Trig on positiv (1) or negative (0) slope for binary inp 9 1 1 0 1 Trig on 0 0 X

TrigLevel09 Trig on positiv (1) or negative (0) slope for binary inp 9 1 1 0 1 Trig on 1 1 X

IndicationMa09 Indication mask for binary channel 9 0 1 0 1 Hide 0 XIndicationMa09 Indication mask for binary channel 9 0 1 0 1 Show 1

SetLED09 Set red-LED on HMI for binary channel 9 0 1 0 1 Off 0 XSetLED09 Set red-LED on HMI for binary channel 9 0 1 0 1 On 1 X

Operation10 Trigger operation On/Off 0 1 0 1 Off 0 XOperation10 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel10 Trig on positiv (1) or negative (0) slope for binary inp 10 1 1 0 1 Trig on 0 0 X

TrigLevel10 Trig on positiv (1) or negative (0) slope for binary inp 10 1 1 0 1 Trig on 1 1 X

IndicationMa10 Indication mask for binary channel 10 0 1 0 1 Hide 0 XIndicationMa10 Indication mask for binary channel 10 0 1 0 1 Show 1

SetLED10 Set red-LED on HMI for binary channel 10 0 1 0 1 Off 0 X

SetLED10 Set red-LED on HMI for binary channel 10 0 1 0 1 On 1 X

Operation11 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(31) of (92)

7/29/2019 OHL setting

32/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation11 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel11 Trig on positiv (1) or negative (0) slope for binary inp 11 1 1 0 1 Trig on 0 0 X

TrigLevel11 Trig on positiv (1) or negative (0) slope for binary inp 11 1 1 0 1 Trig on 1 1 X

IndicationMa11 Indication mask for binary channel 11 0 1 0 1 Hide 0 XIndicationMa11 Indication mask for binary channel 11 0 1 0 1 Show 1

SetLED11 Set red-LED on HMI for binary channel 11 0 1 0 1 Off 0 X

SetLED11 Set red-LED on HMI for binary channel 11 0 1 0 1 On 1 X

Operation12 Trigger operation On/Off 0 1 0 1 Off 0 XOperation12 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel12 Trig on positiv (1) or negative (0) slope for binary inp 12 1 1 0 1 Trig on 0 0 X

TrigLevel12 Trig on positiv (1) or negative (0) slope for binary inp 12 1 1 0 1 Trig on 1 1 XIndicationMa12 Indication mask for binary channel 12 0 1 0 1 Hide 0 XIndicationMa12 Indication mask for binary channel 12 0 1 0 1 Show 1

SetLED12 Set red-LED on HMI for binary input 12 0 1 0 1 Off 0 X

SetLED12 Set red-LED on HMI for binary input 12 0 1 0 1 On 1 X

Operation13 Trigger operation On/Off 0 1 0 1 Off 0 XOperation13 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel13 Trig on positiv (1) or negative (0) slope for binary inp 13 1 1 0 1 Trig on 0 0 X

TrigLevel13 Trig on positiv (1) or negative (0) slope for binary inp 13 1 1 0 1 Trig on 1 1 X

IndicationMa13 Indication mask for binary channel 13 0 1 0 1 Hide 0 XIndicationMa13 Indication mask for binary channel 13 0 1 0 1 Show 1

SetLED13 Set red-LED on HMI for binary channel 13 0 1 0 1 Off 0 X

SetLED13 Set red-LED on HMI for binary channel 13 0 1 0 1 On 1 X

Operation14 Trigger operation On/Off 0 1 0 1 Off 0 XOperation14 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel14 Trig on positiv (1) or negative (0) slope for binary inp 14 1 1 0 1 Trig on 0 0 X

TrigLevel14 Trig on positiv (1) or negative (0) slope for binary inp 14 1 1 0 1 Trig on 1 1 X

IndicationMa14 Indication mask for binary channel 14 0 1 0 1 Hide 0 XIndicationMa14 Indication mask for binary channel 14 0 1 0 1 Show 1

SetLED14 Set red-LED on HMI for binary channel 14 0 1 0 1 Off 0 XSetLED14 Set red-LED on HMI for binary channel 14 0 1 0 1 On 1 X

Operation15 Trigger operation On/Off 0 1 0 1 Off 0 XOperation15 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel15 Trig on positiv (1) or negative (0) slope for binary inp 15 1 1 0 1 Trig on 0 0 X

TrigLevel15 Trig on positiv (1) or negative (0) slope for binary inp 15 1 1 0 1 Trig on 1 1 X

IndicationMa15 Indication mask for binary channel 15 0 1 0 1 Hide 0 XIndicationMa15 Indication mask for binary channel 15 0 1 0 1 Show 1

SetLED15 Set red-LED on HMI for binary channel 15 0 1 0 1 Off 0 X

SetLED15 Set red-LED on HMI for binary channel 15 0 1 0 1 On 1 X

Operation16 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(32) of (92)

7/29/2019 OHL setting

33/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation16 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel16 Trig on positiv (1) or negative (0) slope for binary inp 16 1 1 0 1 Trig on 0 0 X

TrigLevel16 Trig on positiv (1) or negative (0) slope for binary inp 16 1 1 0 1 Trig on 1 1 X

IndicationMa16 Indication mask for binary channel 16 0 1 0 1 Hide 0 XIndicationMa16 Indication mask for binary channel 16 0 1 0 1 Show 1

SetLED16 Set red-LED on HMI for binary channel 16 0 1 0 1 Off 0 X

SetLED16 Set red-LED on HMI for binary channel 16 0 1 0 1 On 1 X

FUNT1 Function type for binary channel 1 (IEC -60870-5-103) 0 255 0 1 FunT XFUNT2 Function type for binary channel 2 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT3 Function type for binary channel 3 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT4 Function type for binary channel 4 (IEC -60870-5-103) 0 255 0 1 FunT XFUNT5 Function type for binary channel 5 (IEC -60870-5-103) 0 255 0 1 FunT XFUNT6 Function type for binary channel 6 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT7 Function type for binary channel 7 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT8 Function type for binary channel 8 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT9 Function type for binary channel 9 (IEC -60870-5-103) 0 255 0 1 FunT XFUNT10 Function type for binary channel 10 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT11 Function type for binary channel 11 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT12 Function type for binary channel 12 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT13 Function type for binary channel 13 (IEC -60870-5-103) 0 255 0 1 FunT XFUNT14 Function type for binary channel 14 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT15 Function type for binary channel 15 (IEC -60870-5-103) 0 255 0 1 FunT X

FUNT16 Function type for binary channel 16 (IEC -60870-5-103) 0 255 0 1 FunT X

INFNO1 Information number for binary channel 1 (IEC -60870-5-103) 0 255 0 1 InfNo XINFNO2 Information number for binary channel 2 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO3 Information number for binary channel 3 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO4 Information number for binary channel 4 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO5 Information number for binary channel 5 (IEC -60870-5-103) 0 255 0 1 InfNo XINFNO6 Information number for binary channel 6 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO7 Information number for binary channel 7 (IEC -60870-5-103) 0 255 0 1 InfNo XINFNO8 Information number for binary channel 8 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO9 Information number for binary channel 9 (IEC -60870-5-103) 0 255 0 1 InfNo XINFNO10 Information number for binary channel 10 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO11 Information number for binary channel 11 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO12 Information number for binary channel 12 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO13 Information number for binary channel 13 (IEC -60870-5-103) 0 255 0 1 InfNo XINFNO14 Information number for binary channel 14 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO15 Information number for binary channel 15 (IEC -60870-5-103) 0 255 0 1 InfNo X

INFNO16 Information number for binary channel 16 (IEC -60870-5-103) 0 255 0 1 InfNo X

Operation17 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(33) of (92)

7/29/2019 OHL setting

34/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation17 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel17 Trig on positiv (1) or negative (0) slope for binary inp 17 1 1 0 1 Trig on 0 0 X

TrigLevel17 Trig on positiv (1) or negative (0) slope for binary inp 17 1 1 0 1 Trig on 1 1 X

IndicationMa17 Indication mask for binary channel 17 0 1 0 1 Hide 0 XIndicationMa17 Indication mask for binary channel 17 0 1 0 1 Show 1

SetLED17 Set red-LED on HMI for binary channel 17 0 1 0 1 Off 0 X

SetLED17 Set red-LED on HMI for binary channel 17 0 1 0 1 On 1 X

Operation18 Trigger operation On/Off 0 1 0 1 Off 0 XOperation18 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel18 Trig on positiv (1) or negative (0) slope for binary inp 18 1 1 0 1 Trig on 0 0 X

TrigLevel18 Trig on positiv (1) or negative (0) slope for binary inp 18 1 1 0 1 Trig on 1 1 X

IndicationMa18 Indication mask for binary channel 18 0 1 0 1 Hide 0 XIndicationMa18 Indication mask for binary channel 18 0 1 0 1 Show 1

SetLED18 Set red-LED on HMI for binary channel 18 0 1 0 1 Off 0 X

SetLED18 Set red-LED on HMI for binary channel 18 0 1 0 1 On 1 X

Operation19 Trigger operation On/Off 0 1 0 1 Off 0 XOperation19 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel19 Trig on positiv (1) or negative (0) slope for binary inp 19 1 1 0 1 Trig on 0 0 X

TrigLevel19 Trig on positiv (1) or negative (0) slope for binary inp 19 1 1 0 1 Trig on 1 1 X

IndicationMa19 Indication mask for binary channel 19 0 1 0 1 Hide 0 XIndicationMa19 Indication mask for binary channel 19 0 1 0 1 Show 1

SetLED19 Set red-LED on HMI for binary channel 19 0 1 0 1 Off 0 X

SetLED19 Set red-LED on HMI for binary channel 19 0 1 0 1 On 1 X

Operation20 Trigger operation On/Off 0 1 0 1 Off 0 XOperation20 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel20 Trig on positiv (1) or negative (0) slope for binary inp 20 1 1 0 1 Trig on 0 0 X

TrigLevel20 Trig on positiv (1) or negative (0) slope for binary inp 20 1 1 0 1 Trig on 1 1 X

IndicationMa20 Indication mask for binary channel 20 0 1 0 1 Hide 0 XIndicationMa20 Indication mask for binary channel 20 0 1 0 1 Show 1

SetLED20 Set red-LED on HMI for binary channel 20 0 1 0 1 Off 0 XSetLED20 Set red-LED on HMI for binary channel 20 0 1 0 1 On 1 X

Operation21 Trigger operation On/Off 0 1 0 1 Off 0 XOperation21 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel21 Trig on positiv (1) or negative (0) slope for binary inp 21 1 1 0 1 Trig on 0 0 X

TrigLevel21 Trig on positiv (1) or negative (0) slope for binary inp 21 1 1 0 1 Trig on 1 1 X

IndicationMa21 Indication mask for binary channel 21 0 1 0 1 Hide 0 XIndicationMa21 Indication mask for binary channel 21 0 1 0 1 Show 1 X

SetLED21 Set red-LED on HMI for binary channel 21 0 1 0 1 Off 0 X

SetLED21 Set red-LED on HMI for binary channel 21 0 1 0 1 On 1 X

Operation22 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(34) of (92)

7/29/2019 OHL setting

35/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation22 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel22 Trig on positiv (1) or negative (0) slope for binary inp 22 1 1 0 1 Trig on 0 0 X

TrigLevel22 Trig on positiv (1) or negative (0) slope for binary inp 22 1 1 0 1 Trig on 1 1 X

IndicationMa22 Indication mask for binary channel 22 0 1 0 1 Hide 0 XIndicationMa22 Indication mask for binary channel 22 0 1 0 1 Show 1

SetLED22 Set red-LED on HMI for binary channel 22 0 1 0 1 Off 0 X

SetLED22 Set red-LED on HMI for binary channel 22 0 1 0 1 On 1 X

Operation23 Trigger operation On/Off 0 1 0 1 Off 0 XOperation23 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel23 Trig on positiv (1) or negative (0) slope for binary inp 23 1 1 0 1 Trig on 0 0 X

TrigLevel23 Trig on positiv (1) or negative (0) slope for binary inp 23 1 1 0 1 Trig on 1 1 X

IndicationMa23 Indication mask for binary channel 23 0 1 0 1 Hide 0 XIndicationMa23 Indication mask for binary channel 23 0 1 0 1 Show 1

SetLED23 Set red-LED on HMI for binary channel 23 0 1 0 1 Off 0 X

SetLED23 Set red-LED on HMI for binary channel 23 0 1 0 1 On 1 X

Operation24 Trigger operation On/Off 0 1 0 1 Off 0 XOperation24 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel24 Trig on positiv (1) or negative (0) slope for binary inp 24 1 1 0 1 Trig on 0 0 X

TrigLevel24 Trig on positiv (1) or negative (0) slope for binary inp 24 1 1 0 1 Trig on 1 1 X

IndicationMa24 Indication mask for binary channel 24 0 1 0 1 Hide 0 XIndicationMa24 Indication mask for binary channel 24 0 1 0 1 Show 1

SetLED24 Set red-LED on HMI for binary channel 24 0 1 0 1 Off 0 X

SetLED24 Set red-LED on HMI for binary channel 24 0 1 0 1 On 1 X

Operation25 Trigger operation On/Off 0 1 0 1 Off 0 XOperation25 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel25 Trig on positiv (1) or negative (0) slope for binary inp 25 1 1 0 1 Trig on 0 0 X

TrigLevel25 Trig on positiv (1) or negative (0) slope for binary inp 25 1 1 0 1 Trig on 1 1 X

IndicationMa25 Indication mask for binary channel 25 0 1 0 1 Hide 0 XIndicationMa25 Indication mask for binary channel 25 0 1 0 1 Show 1

SetLED25 Set red-LED on HMI for binary channel 25 0 1 0 1 Off 0 XSetLED25 Set red-LED on HMI for binary channel 25 0 1 0 1 On 1 X

Operation26 Trigger operation On/Off 0 1 0 1 Off 0 XOperation26 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel26 Trig on positiv (1) or negative (0) slope for binary inp 26 1 1 0 1 Trig on 0 0 X

TrigLevel26 Trig on positiv (1) or negative (0) slope for binary inp 26 1 1 0 1 Trig on 1 1 X

IndicationMa26 Indication mask for binary channel 26 0 1 0 1 Hide 0 XIndicationMa26 Indication mask for binary channel 26 0 1 0 1 Show 1

SetLED26 Set red-LED on HMI for binary channel 26 0 1 0 1 Off 0 X

SetLED26 Set red-LED on HMI for binary channel 26 0 1 0 1 On 1 X

Operation27 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(35) of (92)

7/29/2019 OHL setting

36/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation27 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel27 Trig on positiv (1) or negative (0) slope for binary inp 27 1 1 0 1 Trig on 0 0 X

TrigLevel27 Trig on positiv (1) or negative (0) slope for binary inp 27 1 1 0 1 Trig on 1 1 X

IndicationMa27 Indication mask for binary channel 27 0 1 0 1 Hide 0 XIndicationMa27 Indication mask for binary channel 27 0 1 0 1 Show 1 X

SetLED27 Set red-LED on HMI for binary channel 27 0 1 0 1 Off 0 X

SetLED27 Set red-LED on HMI for binary channel 27 0 1 0 1 On 1 X

Operation28 Trigger operation On/Off 0 1 0 1 Off 0 XOperation28 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel28 Trig on positiv (1) or negative (0) slope for binary inp 28 1 1 0 1 Trig on 0 0 X

TrigLevel28 Trig on positiv (1) or negative (0) slope for binary inp 28 1 1 0 1 Trig on 1 1 X

IndicationMa28 Indication mask for binary channel 28 0 1 0 1 Hide 0 XIndicationMa28 Indication mask for binary channel 28 0 1 0 1 Show 1 X

SetLED28 Set red-LED on HMI for binary input 28 0 1 0 1 Off 0 X

SetLED28 Set red-LED on HMI for binary input 28 0 1 0 1 On 1 X

Operation29 Trigger operation On/Off 0 1 0 1 Off 0 XOperation29 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel29 Trig on positiv (1) or negative (0) slope for binary inp 29 1 1 0 1 Trig on 0 0 X

TrigLevel29 Trig on positiv (1) or negative (0) slope for binary inp 29 1 1 0 1 Trig on 1 1 X

IndicationMa29 Indication mask for binary channel 29 0 1 0 1 Hide 0 XIndicationMa29 Indication mask for binary channel 29 0 1 0 1 Show 1

SetLED29 Set red-LED on HMI for binary channel 29 0 1 0 1 Off 0 X

SetLED29 Set red-LED on HMI for binary channel 29 0 1 0 1 On 1 X

Operation30 Trigger operation On/Off 0 1 0 1 Off 0 XOperation30 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel30 Trig on positiv (1) or negative (0) slope for binary inp 30 1 1 0 1 Trig on 0 0 X

TrigLevel30 Trig on positiv (1) or negative (0) slope for binary inp 30 1 1 0 1 Trig on 1 1 X

IndicationMa30 Indication mask for binary channel 30 0 1 0 1 Hide 0 XIndicationMa30 Indication mask for binary channel 30 0 1 0 1 Show 1 X

SetLED30 Set red-LED on HMI for binary channel 30 0 1 0 1 Off 0 XSetLED30 Set red-LED on HMI for binary channel 30 0 1 0 1 On 1 X

Operation31 Trigger operation On/Off 0 1 0 1 Off 0 XOperation31 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel31 Trig on positiv (1) or negative (0) slope for binary inp 31 1 1 0 1 Trig on 0 0 X

TrigLevel31 Trig on positiv (1) or negative (0) slope for binary inp 31 1 1 0 1 Trig on 1 1 X

IndicationMa31 Indication mask for binary channel 31 0 1 0 1 Hide 0 XIndicationMa31 Indication mask for binary channel 31 0 1 0 1 Show 1 X

SetLED31 Set red-LED on HMI for binary channel 31 0 1 0 1 Off 0 X

SetLED31 Set red-LED on HMI for binary channel 31 0 1 0 1 On 1 X

Operation32 Trigger operation On/Off 0 1 0 1 Off 0 X

Page(36) of (92)

7/29/2019 OHL setting

37/92

PROTECTION SETTINGS ABB ABPROJECT STATION DOCUMENT NUMBER REVISION

Stage 5 Faeda 1WAR 968033-LAD -

CUSTOMER BAY PREPARED Department Date

KRG-MOE =E1.Q5 L Bodin PSSX/SSKS 2012-09-21

ABB Ref. RELAY APPROVED Department DateA10680 REL 670 Prim L Bodin PSSX/SSKS 2012-09-21

FUNCTION INSTANCE DESCRIPTION

BxRBDR 1-6 Dist. rec. Binary inputsParameter name Parameter desc Default

value

Max Min Step Enum Enum value Default Comment

Operation32 Trigger operation On/Off 0 1 0 1 On 1 X

TrigLevel32 Trig on positiv (1) or negative (0) slope for binary inp 32 1 1 0 1 Trig on 0 0 X

TrigLevel32 Trig on positiv (1) or negative (0) slope for binary inp 32 1