nutiny-sdk-nuc131sd2ae user manual · nutiny-sdk- nuc131 series user manual des. 24, 2014 3 of 21...
TRANSCRIPT
NuTiny-SDK-NUC131 Series User Manual
Des. 24, 2014 Rev. 1.00
NuTiny-SDK-NUC131SD2AE User Manual
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro™
microcontroller based system design.
Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 2 of 21 Rev. 1.00
Table of Contents
1 Overview ........................................................................................... 3
2 Introduction to NuTiny-SDK- NUC131SD2AE .......................................... 4
1. NuTiny-SDK- NUC131SD2AE Jumper Description ........................................... 5 2. Pin Assignment for Extended Connectors ...................................................... 6 3. NuTiny-SDK- NUC131SD2AE PCB Placement ................................................. 8
3 Starting to Use NuTiny-SDK- NUC131SD2AE on the Keil μVision® IDE ....... 9
4. Downloading and Installing Keil μVision® IDE Software ................................... 9 5. Downloading and Installing Nuvoton Nu-Link Driver ....................................... 9 6. Hardware Setup ......................................................................................... 9 7. Example Program ..................................................................................... 10
4 Starting to Use NuTiny-SDK- NUC131SD2AE on the IAR Embedded Workbench ............................................................................................. 11
8. Downloading and Installing IAR Embedded Workbench Software .................... 11 9. Downloading and Installing Nuvoton Nu-Link Driver ..................................... 11 10. Hardware Setup ....................................................................................... 11 11. Example Program ..................................................................................... 12
5 NuTiny-SDK- NUC131SD2AE Schematics ............................................. 13
12. NuTiny-EVB- NUC131SD2AE Schematic ...................................................... 13 13. NuTiny-EVB- NUC131SD2AE Schematic ...................................................... 14 14. Nu-Link-Me Schematic .............................................................................. 15
6 Downloading NuMicro™ Related Files from Nuvoton Website .................. 16
15. Downloading NuMicro™ Keil μVision® IDE Driver .......................................... 16 16. Downloading NuMicro™ IAR EWARM Driver ................................................. 18 17. Downloading NuMicro™ NUC131SD2AE Series BSP Software Library .............. 20
7 Revision History ............................................................................... 22
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 3 of 21 Rev. 1.00
1 Overview The NuTiny-SDK- NUC131SD2AE is a specific development tool for NuMicro™ M0518 series by which users can develop and verify the application program easily. The NuTiny-SDK-NUC131SD2AE includes two portions: NuTiny-EVB-NUC131SD2AE (an evaluation board) and Nu-Link-Me (Debug Adaptor). With the NuTiny-SDK-NUC131SD2AE, users do not need additional ICE or debug equipment.
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 4 of 21 Rev. 1.00
2 Introduction to NuTiny-SDK- NUC131SD2AE The following figure shows the NuTiny-SDK- NUC131SD2AE for NUC131SD2AE series, in which the left portion is called NuTiny-EVB- NUC131SD2AE and the right portion is Debug Adaptor called Nu-Link-Me. The NuTiny-EVB- NUC131SD2AE is similar to other development board. Users can use it to develop and verify applications to emulate the real behavior. In fact, the real chip NUC131SD2AE is mounted on the board. The NuTiny-EVB- NUC131SD2AE can be a real system controller to design user target system. The Nu-Link-Me is a Debug Adaptor which connects the USB port of your PC to your target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor with Keil or IAR, please refer to “Nuvoton NuMicro™ IAR ICE Driver User Manual” or Nuvoton NuMicro™ Keil ICE Driver User Manual” for details.
Target Chip ICE ControllerVCC:3.3V or 5V
(JP8)
ICE Controller
USB Connector
(ICEJ2)
VSS
(JP2)
VDD
(JP1)
Reset Key
(SW1)
LQFP-64 pin
Extended Connector
(JP7, JP6)
LQFP-64 pin
Extended Connector
(JP4, JP5)
I/O LED
Power LED
Figure 2-1 NuTiny-SDK- NUC131SD2AE (Green PCB Board)
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 5 of 21 Rev. 1.00
1. NuTiny-SDK- NUC131SD2AE Jumper Description
2.1.1 Power Settings
JP1: VDD Voltage connecter in NuTiny-EVB- NUC131SD2AE
J1: USB port in Nu-Link-Me
Model JPR1 J1 USB port JP1 VDD MCU Voltage
Model 1 Select VCC33
(default) Connect to PC DC 3.3V output DC 3.3V
Model 2 X X DC 2.5 V ~ 5.5 V
Input Voltage by JP1
input
X: Unused.
2.1.2 Debug Connectors
JP3: Connector in target board (NuTiny-EVB- NUC131SD2AE) for connecting with Nuvoton ICE adaptor (Nu-Link-Me)
JP8: Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board (e.g. NuTiny-EVB- NUC131SD2AE)
2.1.3 USB Connectors
J1: Mini USB Connector in Nu-Link-Me connected to a PC USB port
2.1.4 Extended Connectors
JP4, JP5, JP6 and JP7: Show all chip pins in NuTiny-EVB- NUC131SD2AE
2.1.5 Buttons
SW1: Reset button in NuTiny-EVB- NUC131SD2AE
2.1.6 Power Connectors
JP1: VDD connector in NuTiny-EVB- NUC131SD2AE
JP2: VSS connector in NuTiny-EVB- NUC131SD2AE
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 6 of 21 Rev. 1.00
2. Pin Assignment for Extended Connectors
The NuTiny-EVB- NUC131SD2AE provides the NUC131SD2AE target chip on board
and the extended connectors (JP4, JP5, JP6 and JP7) for LQFP48-pin. The following table is the pin assignment for NUC131SD2AE.
Pin No Pin Name Pin No Pin Name
01 PB.14,INT0 33 PC.11,PWM1_BRAKE1
02 PB.13 34 PC.10,PWM1_BRAKE0
03 PB.12,CLKO,BPWM1_CH3
35 PC.9,PWM0_BRAKE1
04 PF.5,I2C0_SCL,PWM1_CH5
36 PC.8,PWM0_BRAKE0
05 PF.4,I2C0_SDA,PWM1_CH4
37 PA.15,PWM0_CH3
06 PA.11,I2C1_SCL,PWM1_CH3
38 PA.14,PWM0_CH2
07 PA.10,I2C1_SDA,PWM1_CH2
39 PA.13,PWM0_CH1,UART5_TXD
08 PA.9,I2C0_SCL,UART1_nCTS
40 PA.12,PWM0_CH0,UART5_RXD
09 PA.8,I2C0_SDA,UART1_nRTS
41 PF.7,ICE_DAT
10 PB.4,UART1_RXD 42 PF.6,ICE_CLK
11 PB.5,UART1_TXD 43 AVSS
12 PB.6,UART1_nRTS 44 PA.0,PWM0_CH4,ADC0,I2C1_SCL,UART5_TXD
13 PB.7,UART1_nCTS 45 PA.1,PWM0_CH5,ADC1,I2C1_SDA,UART5_RXD
14 LDO_CAP 46 PA.2,PWM1_CH0,ADC2,UART3_TXD
15 VDD 47 PA.3,PWM1_CH1,ADC3,UART3_RXD
16 VSS 48 PA.4,ADC4
17 PB.0,UART0_RXD 49 PA.5,UART3_RXD,ADC5
18 PB.1,UART0_TXD 50 PA.6,UART3_TXD,ADC6
19 PB.2,UART0_nRTS,TM2_EXT,TM2,PWM1_BRAKE1
51 PA.7,Vref,ADC7
20 PB.3,UART0_nCTS,TM3_EXT,TM3,PWM1_BRAKE0
52 AVDD
21 PD.6,BPWM1_CH1,CAN0 53 PC.7,PWM0_BRAKE1,I2C0_S
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 7 of 21 Rev. 1.00
_RXD CL,UART4_RXD
22 PD.7,BPWM1_CH0,CAN0_TXD
54 PC.6,PWM0_BRAKE0,I2C0_SDA,UART4_TXD
23 PD.14,BPWM0_CH5,UART2_RXD
55 PC.15
24 PD.15,BPWM0_CH4,UART2_TXD
56 PC.14
25 PC.3,BPWM0_CH3,SPI0_MOSI0
57 PB.15, ,BPWM1_CH5TM0,TM0_EXT,INT1
26 PC.2,BPWM0_CH2,SPI0_MISO0
58 PF.0,XT1_OUT
27 PC.1,BPWM0_CH1,SPI0_CLK
59 PF.1,XT1_IN
28 PC.0,BPWM0_CH0,SPI0_SS0
60 nRESET
29 PE.5,PWM0_CH5,TM1_EXT,TM1
61 VSS
30 PB.11,TM3,PWM0_CH4 62 VDD
31 PB.10,TM2 63 PF.8, PWM1_CH4,CLKO
32 PB.9,TM1 64 PB.8,BPWM1_CH2,CLKO,TM0,STADC
Table 2-1 Pin Assignment for NUC131SD2AE
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 8 of 21 Rev. 1.00
3. NuTiny-SDK- NUC131SD2AE PCB Placement
The following figure shows the NuTiny-SDK- NUC131SD2AE PCB placement.
Figure 2-2 NuTiny-SDK- NUC131SD2AE PCB Placement
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 9 of 21 Rev. 1.00
3 Starting to Use NuTiny-SDK- NUC131SD2AE on the Keil μVision® IDE
4. Downloading and Installing Keil μVision® IDE Software
Please connect to the Keil company website (http://www.keil.com) to download the Keil μVision
® IDE and install the RVMDK.
5. Downloading and Installing Nuvoton Nu-Link Driver
Please connect to Nuvoton NuMicro™ website (http://www.nuvoton.com/NuMicro) to download the “NuMicro™ Keil μVision
® IDE driver” file. Please refer to section 15 for
the detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the “Nu-Link_Keil_Driver.exe” to install the driver.
6. Hardware Setup
The hardware setup is shown in the following figure.
Figure 3-1 NuTiny-SDK- NUC131SD2AE Hardware Setup
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 10 of 21 Rev. 1.00
7. Example Program
This example demonstrates how to download and debug an application on a NuTiny-SDK- NUC131SD2AE board. The example file can be found in the directory list shown in the following figure.
Directory
Figure 3-2 Example Directory
To use this example: The I/O LED on the NuTiny-EVB- NUC131SD2AE board will turn on.
Start μVision®
Project – Open Open the SYS.uvproj project file
Project – Build Compile and link the SYS application
Flash – Download Program the application code into on-chip Flash ROM
Start Debug mode When using the debugger commands, you may:
Review variables in the watch window
Single step through code
Reset the device
Run the application
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 11 of 21 Rev. 1.00
4 Starting to Use NuTiny-SDK- NUC131SD2AE on the IAR Embedded
Workbench
8. Downloading and Installing IAR Embedded Workbench Software
Please connect to IAR company website (http://www.iar.com) to download the IAR Embedded Workbench and install the EWARM.
9. Downloading and Installing Nuvoton Nu-Link Driver
Please connect to Nuvoton Company NuMicro™
website (http://www.nuvoton.com/NuMicro) to download “NuMicro™ IAR EWARM Driver” file. Please refer to section 16 for the detail download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the “Nu-Link_IAR_Driver.exe” to install the driver.
10. Hardware Setup
The hardware setup is shown in the following figure.
Figure 4-1 NuTiny-SDK- NUC131SD2AE Hardware Setup
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 12 of 21 Rev. 1.00
11. Example Program
This example demonstrates how to download and debug an application on a NuTiny-SDK- NUC131SD2AE board. The example file can be found in the directory list shown in the following figure.
Directory
Figure 4-2 Example Directory
To use this example: The I/O LED on the NuTiny-EVB- NUC131SD2AE board will turn on.
Start IAR Embedded Workbench
File-Open-Workspace Open the SYS.eww workspace file
Project - Make Compile and link the SYS application
Project – Download and Debug Program the application code into on-chip Flash ROM
Single step through code
Reset the device
Run the application
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 13 of 21 Rev. 1.00
5 NuTiny-SDK- NUC131SD2AE Schematics
12. NuTiny-EVB- NUC131SD2AE Schematic
P52 P29P28P27
P22P21
P26P25P24P23
P19P18P17
P20
P56P57P58D12MOP59D12MIP60RESET
P53P54
P49P50
P61P62P63P64
P55
DVCC5
P51
Off-page Connector
P[1:64]P[1:64]
D12MI
D12MO
D12MI
D12MO
CB3
0.1u
C0603
DAVDD
ADAVSS
Title
Size Document Number Rev
Date: Sheet of
<Doc> <Rev Code>
NUTINY-SDK-NUC131
Custom
3 3Thursday , December 25, 2014
U2
NUC131SD2AE_LQFP64
SPI0_SS0/BPWM0_CH0/PC.028TM1_EXT/TM1/PWM0_CH5/PE.529TM3/PWM0_CH4/PB.1130TM2/PB.1031TM1/PB.932
PA.5/UART3_RXD/ADC549
PA.6/UART3_TXD/ADC650
PA.7/Vref /ADC751
PB
.14
/IN
T0
1
PB
.13
2
PB
.12
/CL
KO
/BP
WM
1_
CH
33
PF
.5/I
2C
0_
SC
L/P
WM
1_
CH
54
PF
.4/I
2C
0_
SD
A/P
WM
1_
CH
45
PA
.11
/I2
C1
_S
CL
/PW
M1
_C
H3
6
PA
.10
/I2
C1
_S
DA
/PW
M1
_C
H2
7
PA
.9/I
2C
0_
SC
L/U
AR
T1
_n
CT
S8
PB
.4/U
AR
T1
_R
XD
10
LD
O_
CA
P14
VD
D15
VS
S16
UART0_RXD/PB.017UART0_TXD/PB.118UART0_nRTS/TM2_EXT/TM2/PWM1_BRAKE1/PB.219UART0_nCTS/TM3_EXT/TM3/PWM1_BRAKE0/PB.320CAN0_RXD/BPWM1_CH1/PD.621CAN0_TXD/BPWM1_CH0/PD.722UART2_RXD/BPWM0_CH5/PD.1423
AVDD52
PC.7/PWM0_BRAKE1/I2C0_SCL/UART4_RXD53
PC.6/PWM0_BRAKE0/I2C0_SDA/UART4_TXD54
PB.15/BPWM1_CH5/TM0/TM0_EXT/INT157
PC.1555
PC.1456
PF.0/XT1_OUT58
PF.1/XT1_IN59
nRESET60
VSS61
PB
.7/U
AR
T1
_n
CT
S13
PB
.6/U
AR
T1
_n
RT
S12
SPI0_CLK/BPWM0_CH1/PC.127
SPI0_MISO0/BPWM0_CH2/PC.226
SPI0_MOSI0/BPWM0_CH3/PC.325
UART2_TXD/BPWM0_CH4/PD.1524
VDD62
PB.8/BPWM1_CH2/CLKO/TM0/STADC64 PF.8/PWM1_CH4/CLKO63
PA
.8/I
2C
0_
SD
A/U
AR
T1
_n
RT
S9
PB
.5/U
AR
T1
_T
XD
11
PW
M1
_B
RA
KE
1/P
C.1
133
PW
M1
_B
RA
KE
0/P
C.1
034
PW
M0
_B
RA
KE
1/P
C.9
35
PW
M0
_B
RA
KE
0/P
C.8
36
PW
M0
_C
H3
/PA
.15
37
PW
M0
_C
H2
/PA
.14
38
PW
M0
_C
H1
/UA
RT
5_
TX
D/P
A.1
339
PW
M0
_C
H0
/UA
RT
5_
RX
D/P
A.1
240
ICE
_D
AT
/PF
.741
AV
SS
43
AD
C0
/PW
M0
_C
H4
/I2
C1
_S
CL
/UA
RT
5_
TX
D/P
A.0
44
ICE
_C
LK
/PF
.642
AD
C1
/PW
M0
_C
H5
/I2
C1
_S
DA
/UA
RT
5_
RX
D/P
A.1
45
AD
C2
/PW
M1
_C
H0
/UA
RT
3_
TX
D/P
A.2
46
AD
C3
/PW
M1
_C
H1
/UA
RT
3_
RX
D/P
A.3
47
AD
C4
/PA
.448
P43
CB4
0.1u
C0603
GND
VCC
GND
VCC5P
1
CB5
0.1u
C0603
CT2
1uF/6.3V
TANT-A
P2
P3
P4
P5
P6
P7
P14
P13
P12
P11
P10
P9
P8
JP11
12
P16
P41
ICE
_D
AT
P42
ICE
_C
LK
P44
P45
P46
P47
P48
P33
P34
P35
P36
P37
P38
P39
P40
DVCC5
R80
P15
P30P31P32
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 14 of 21 Rev. 1.00
13. NuTiny-EVB- NUC131SD2AE Schematic
D12MOD12MO
D12MI
TICEDVDD5TICEDVDD5
D12MI
P1
P5P3
JP4
NC
1 23 45 67 89 1011 1213 1415 16
JP5
NC
1 23 45 67 89 1011 1213 1415 16
JP6
NC
1 23 45 67 89 1011 1213 1415 16
JP7
NC
1 23 45 67 89 1011 1213 1415 16
P15P13P11
P7P9
P4
P14P16
P8
P12
P6
P10
P17
P31
P23
P2
P25
P29
P19P21
P27
P18
P32
P24
P30
P20P22
P47
P39
P33
P26P28
P36
P41
P45
P35P37 P38
P44
P48
P40
P34
P46
P51
P63
P55
P49
P42
P62
P53
P59P57
P61
P52P54
P60
P64
P56
P50
P43P58
connect
R2
510R0603
12
IO1
Red0805 N2
DVCC5
P2
TICERSTTICECLKTICEDAT
Title
Size Document Number Rev
Date: Sheet of
1.0
NUTINY-SDK-NUC131
Custom
Thursday , December 04, 2014
IO
12
POWER1
Green0805
PR1
510R0603
DVCC5
N1
VCC5
D12MI
GND
VCC
D12MO
VCC
GND
VCC5
GND
LED
ICEDAT
ICERST
DVCC5JP3
NC
1 23 45 67 89 10
ICECLK
DVCC5
C1
10uF/10V
TANT-A
R1
10K
R0603
RESET
ICERST
SW1
PUSH BOTTOM
SW
C320p
C0603
X112MHz
XTAL3-1
C220p
C0603
TICEDAT ICEDATTICECLK ICECLKTICERST ICERST
DVCC5 JP1
NC
12
JP2
NC
12
Reset
Crystal
ICE INTERFACE
Power
Off-page Connector
P[1:64]P[1:64]
VCC5
ADAVSS
DVCC5
DAVDD L1
L0603
L2
L0603
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 15 of 21 Rev. 1.00
14. Nu-Link-Me Schematic
ICE_RST
12
IDLE1
Red0805
ISPLED
RED
12
ICP1
Yellow0805
12
ICE1
Red0805ICELED
RP1
8P4R-330
8P4RA
1 23 45 67 8
12
BUSY1
Green0805
VCC5
GREEN
L4L0603
C620p
C0603
L5
L0805
R7100R0603
R6100R0603
R4
33
R0603
X212MHz
XTAL3-1
J1mini USB 5pin
USB_MINI_B
GND5 NC4 DP3 DM2 VCC1
SHIELD6
SHIELD7
SHIELD8
SHIELD9
R5
NC
R0603
L3L0603
C520p
C0603
USBVBUS
AVDD
ADAVSS
NUC_RST#
R3
10K
R0603
CP1
10uF/10V
TANT-A
C4
10uF/10V
TANT-A
P3V
VCC5
VCC5
TICEDATTICECLKTICERST
VCC5
Title
Size Document Number Rev
Date: Sheet of
1.0
NuLink-Me
Custom
Thursday , December 04, 2014
JP8
NC
1 23 45 67 89 10
TICECLKTICEDAT
TICERST
VCC5
JP9
NC
12345
VCC
VCC5
GND
ICE_CLKICE_RST
ICE_DAT
ICE CONNECT IF
DEBUG
12M_I
N3
DMDP
12M_O
U1
NUC12SRE3AN
PA0/ADC044PA1/ADC145PA2/ADC246PA3/ADC347PA4/ADC448INT0/PB14
1
CPO1/PB132
CPO0/PB123
VB
US
17
VD
D3
318
D-
19
D+
20
PB
0/R
X0
21
PB
1/T
X0
22
PB
2/R
TS
023
PB
3/C
TS
024
PC
2/S
DI0
026
PC
1/S
PC
LK
027
PC
0/S
S0
028
PC11/SDO1033PC10/SDI1034PC9/SPCLK135PC8/SS1036PA15/PWM337PA14/PWM238PA13/PWM139
X32I4
X32O5
I2C1SCL/PA116
I2C0SDA/PA89
I2C1SDA/PA107
I2C0SCL/PA98
RX1/PB410
TX1/PB511
RTS1/PB612
CTS1/PB713
PC
3/S
DO
00
25
AVSS43
ICE_CK42
ICE_DAT41
PA12/PWM040
LDO14
VSS16 VDD15
AD
C/P
A5
49
AD
C6
/PA
650
AD
C7
/PA
751
AV
DD
52
CP
N0
/PC
753
CP
P0
/PC
654
CP
N1
/PC
15
55
CP
P1
/PC
14
56
INT
1/P
B1
557
XT
1_O
ut
58
XT
1_In
59
/RE
SE
T60
VS
S1
61
VD
D1
62
PV
SS
63
ST
AD
C/T
M0
/PB
864
PE
529
PB
11/T
M3
30
PB
10/S
S0
1/T
M2
31
PB
9/S
S1
1/T
M1
32
VCC5
RTIDA1
100K
R0603
RICK1
100K
R0603
VCC5
JP10
NC
1234
DMDP
USBVBUS
12
D1
SS24ARB060L
12M
_I
PVSS
AVDD
VCC5
NU
C_
RS
T#
12M
_O
ISPLEDREDGREEN
CT1
1uF/6.3V
TANT-R
CB10.1u
C0603
VCC5
ICELED
USBVBUS
VB
US
US
B_
D+
US
B_
D-
CB20.1u
C0603
C7
1u
C0603
RTDA3
0R0603
TICERST
RTDA2
33
R0603
RTCK1
100K
R0603
TICECLKTICEDAT
TICERST
RTDA1
100K
R0603
RRSET1
100K
R0603
ADAVSS
VCC5
ICE_CLKICE_DAT
1 2
PD1SS24A
RB060L
USBVBUS
P5V
TICEVCC
VCC5
JPR1
HEADER 3
123UP1AMS1117_3.3v
IN3
GN
D1
OU
T2
OU
T4
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 16 of 21 Rev. 1.00
6 Downloading NuMicro™ Related Files from Nuvoton Website
15. Downloading NuMicro™ Keil μVision® IDE Driver
Step1
Visit the Nuvoton NuMicro™
website: http://www.nuvoton.com/NuMicro.
Step2
2-1. Move to “Support”
2-2. Click here to enter Tool & Software
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 17 of 21 Rev. 1.00
Step3
Step4
Step5
Download the NuMicro
™ Keil μVision
® IDE driver.
Click here to download the file.
Click here to enter Software
download page
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 18 of 21 Rev. 1.00
16. Downloading NuMicro™ IAR EWARM Driver
Step1
Visit the Nuvoton NuMicro™
website: http://www.nuvoton.com/NuMicro.
Step2
2-1. Move to “Support”
2-2. Click here to enter Tool & Software
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 19 of 21 Rev. 1.00
Step3
Step4
Step5
Download the NuMicro™
IAR EWARM driver.
Click here to download the file.
Click here to enter Software
download page
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 20 of 21 Rev. 1.00
17. Downloading NuMicro™ NUC131SD2AE Series BSP Software Library
Step1
Visit the Nuvoton NuMicro™
website: http://www.nuvoton.com/NuMicro.
Step2
2-1. Move to “Support”
2-2. Click here to enter Tool & Software
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 21 of 21 Rev. 1.00
Step3
Step4
Download the NuMicro™
NUC131 Series CMSIS BSP.
Click here to enter Software
download page
NuTiny-SDK- NUC131 series User Manual
Des. 24, 2014 22 of 21 Rev. 1.00
7 Revision History
Revision Date Description
1.00 Des. 25, 2014 Preliminary version.
Important Notice
Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any
malfunction or failure of which may cause loss of human life, bodily injury or severe property damage.
Such applications are deemed, “Insecure Usage”.
Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy
control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or
safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and
other applications intended to support or sustain life.
All Insecure Usage shall be made at customer’s risk, and in the event that third parties lay claims to
Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the damages and
liabilities thus incurred by Nuvoton.