new: 2022 series filter assembly - 2022 series filter assembly ... a sae j514 straight thread b...

Download NEW: 2022 Series Filter Assembly - 2022 Series Filter Assembly ... A SAE J514 straight thread B NPT…

Post on 15-Jun-2018

213 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • NEW: 2022 SeriesFilter Assembly

    Data Sheet PIM 2022

    Features

    316 Stainless Steel construction

    Accepts Pall 212 diameter elements with M3 seals

    Optional bypass valve

    Flows to 110 Lpm (30 gpm)

    Pressures to: 17.9 bar (260 psi)

    Port size: 34 and 1

    Notes and SpecificationsMaximum Working Pressure: 17.9 bar (260 psi)

    40 C (104 F)Design Pressure: 13.8 bar (200 psi)

    150 C (302 F)Materials of Construction: 316 stainless steel Element Construction:Poly-Fine XLD cartridges All polypropylene constructionDynalloy cartridges Sintered 316 stainless steel

    fibersDynamesh cartridges Woven 316 stainless steel

    wire cloth

    Pressure Drop InformationFigure 1. Housing pressure drop.Housing pressure drop is directly proportional to specificgravity.

    Element Pressure Drop. For liquids other than water, multiply pressure drop x newviscosity in cSt x new S.G.

    1

    Flow Rate (gpm)

    Diff

    eren

    tialP

    ress

    ure

    (psi

    d)

    03

    0405

    MEDIA

    GRAD

    E 06

    09

    12

    40

    .1

    .07

    .05

    .04

    .03

    .02

    .01

    1

    .7

    .5

    .4

    .3

    .2

    2 3 4 7 10 20 30 4050 70 100

    0.5

    0.4

    0.3

    0.2

    0.1

    0

    8

    6

    4

    2

    00

    0 25 50 75 100

    10 20 30Flow Rate (gpm)

    Flow Rate (Lpm)

    Diff

    eren

    tialP

    ress

    ure

    (bar

    )

    Diff

    eren

    tialP

    ress

    ure

    (psi

    d)

    Note: For liquid other than water, multiply the pressure dropby the specific gravity of the fluid.

    2022 series filter housing

    0.3

    0.25

    0.3

    0.15

    0.1

    0.05

    01 2 4 5

    Flow Rate (gpm)

    Diff

    eren

    tialP

    ress

    ure

    (psi

    d)

    3 6

    3.0 m

    4.5 m

    10 m

    20 m

    Dynalloy/Dynamesh Series Filter Cartridges

    Poly-Fine XLD Series Filter Cartridges

  • Copyright 2006, Pall Corporation. Pall, , are trademarks of Pall Corporation. Indicates a Pall trademark registered in the USA. is a service mark of Pall Corporation.

    Ordering Information

    Assembly P/N: H 2022 ++ T

    Table 1 Table 2 Table 4 Table 5 Table 6 Table 7

    Poly-Fine XLD Cartridge P/N:XLD - U M3

    Table 3 Table 4 Table 1

    Dynalloy Cartridge P/N:PSP - S M3*

    Table 3 Table 4

    *Note: O-ring seals must be ordered separately. Order 2 pieces p/n D10540-456 for nitrile, 2 pieces p/n D10540-457 for fluorocarbon

    Dynamesh Cartridge P/N:PWC - S M3*

    Table 3 Table 4

    *Note: O-ring seals must be ordered separately. Order 2 pieces p/n D10540-456 for nitrile, 2 pieces p/n D10540-457 for fluorocarbon

    Dimensional Drawings Table 1: Seal OptionsHousing Cartridge SealsCode Code*

    H N Nitrile

    Z V Fluoro-carbon

    * Poly-Fine XLD cartridges only

    Table 3: Filter Cartridge Options

    Cartridge Series Code Rating Rating Method

    3 3 m

    4.5 4.5 m

    10 10 m

    20 20 m

    03 3 m

    04 4 m

    05 5 m

    06 6 m

    09 9 m

    10 12 m

    40 40 m

    70 70 m

    100 100 m

    Table 6: Differential Pressure Indicator Options*

    Code Indicator

    E SST visual with glasscover

    B SST port plug

    * Note: Other indicator options available contact factory

    Table 2: Port Options

    Code Port

    A12 3/4 SAE J514 straight thread

    B12 3/4 NPT

    A16 1 SAE J514 straight thread

    B16 NPT

    Table 4: Length Options

    Housing Element LengthCode Code (in)*

    K 10 10

    L 20 20

    * Nominal length in inches

    Table 5: Bypass Valve Options

    Code Valve

    A 1.7 bar (25 psid)

    B 3.4 bar (50 psid)

    N Non- bypass

    Table 7: Mounting BracketOptions

    Code Option

    0 none

    1 Mounting bracket kit

    Industrial Manufacturing25 Harbor Park DrivePort Washington, NY 11050

    888.333.7255 toll free516.484.3600 phone 516.484.6247 fax

    Pall Corporation has offices and plants throughout the world in locations including: Argentina,Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, India, Indonesia, Ireland,Italy, Japan, Korea, Malaysia, Mexico, the Netherlands, New Zealand, Norway, Poland, PuertoRico, Russia, Singapore, South Africa, Spain, Sweden, Switzerland, Taiwan, Thailand, UnitedKingdom, United States, and Venezuela. Distributors are located in all major industrial areasof the world.

    Visit us on the Web at www.pall.com/m&e

    Poly-Fine XLD 99.9% efficiency

    Absolute

    NominalDynamesh

    Dynalloy

    PALL

    INLET

    OU

    TLET

    B B

    4 3/16

    1 1/2

    1 3/16 TYP

    (4) 1/4-20x1/2

    2 5/8

    1 5/16 TYP

    K=13 3/4 LG 3 9/16

    1

    REQUIRED SPACENEEDED FOR SHELLREMOVAL

    K=12-5/8 L=22-1/2

    L=23 3/4 LG

  • 7500/02 Series Spin-On Filter Assemblies

    Description

    Flows to 90 gpm (325 L/min) (7500); 150gpm (565 L/min) (7502) Pressures to 200 psi (14 bar) Port sizes: 1", 1-1/4" and 1-1/2" (7500) 1-1/2" and 2" (7502)

    Specifications

    Features

    Optional Differential Pressure Devices Full Flow Fast Response Bypass Valve Gasket Seal Spin-On Canister Mounting Surface Gray Cast Iron Head O-Ring Seals Ultipor III Element Optional Anti-Back Flow Valve (not shown). Prevents drainage of reservoir or lines where filter is

    mounted below fluid level

    Maximum Acceptable Working Pressure: 200 psi (14 bar) Fatigue Pressure Rating: 200 psi (14 bar) (100,000 cycles 0-200 psi) Typical Burst Pressure: 290 psi (20 bar) (Gasket extrusion) Temperature Range: Nitrile seals -20F to 225F (-29C to 107C) Fluorocarbon seals -20F to 250F (-29C to 120C) 140F (60C) maximum in HWCF or water-glycol fluids Dry Weights: 7500: R length8 lbs. (3.6 kg) S length9 lbs. (4.1 kg) 7502: R length20 lbs. (9.1 kg) S length22 lbs. (10 kg) Filter Element Collapse Pressure: 7500100 psid (7 bar) 7502100 psid (7 bar) Caution: 100 psi (7 bar) maximum for 7500/7502 Series non-bypass valve options (prevents possible filter element collapse)

    Dimensional Drawings

  • Performance

  • Element Pressure Drop Factor Multiply actual flow rate times factor to determine pressure drop with fluid at 150 SUS (32 cSt), 0.9 S.G. Correct for other viscosities by multiplying new viscosity in SUS/150 x new S.G/0.9.

    7502 series uses two 7500 series elements. Factors above are for flow through both elements in a 7502.

    Ordering Information

    7500 Series Element P factor (psid/gpm)

    Length KZ KP KN KS KT

    4" N/A 0.21 0.18 0.14 0.10

    8" 0.23 0.11 0.10 0.07 0.05

    7502 Series Element P factor (psid/gpm)

    Length KZ KP KN KS KT

    4" N/A 0.10 0.09 0.07 0.05

    8" 0.12 0.05 0.05 0.04 0.03

    Assembly P/N: H 750 Table1 Table2 Table3 Table4 Table5 Table6 Table7 Table8

    Element P/N: HC 7500 S

  • Note: Choose from the options in the following tables to compile the specific Product Number.

    TABLE 1: SEAL OPTIONS

    Code Seals

    H Nitrile

    Z* Fluorocarbon

    *Non-standard: available for KP media only.

    TABLE 2: HOUSING OPTIONS

    Code Description

    0 Single element

    2 Double element

    TABLE 3: PORT STYLE OPTIONS

    Code Port Style

    A SAE J514 straight thread

    B NPT

    D* Flange SAE J518c-Code 61

    *7502 series only.

    TABLE 4: PORT SIZE OPTIONS

    Code Size Availability

    16 1" 7500

    20 1-1/4" 7500

    24 1-1/2" 7500/7502

    32 2" 7502*

    *A & B port styles only.

    TABLE 5: FILTER ELEMENT OPTIONS

    Code x 200 x(c)=1000

    KZ*

  • KP 3 5

    KN 6 7

    KS 12 12

    KT 25 22

    *8" length only

    TABLE 6: LENGTH OPTIONS*

    Assembly Code Element Code**

    R 4

    S 8

    * Use code in second column for element part no. ** Nominal length in inches.

    TABLE 7: BYPASS VALVE OPTIONS

    Code Description

    A 25 psid

    B 50 psid

    W Non-bypass

    8 25 psid with ABFV*

    9 50 psid with ABFV

    V Non-bypass with ABFV

    * ABFV - Anti-backflow valve.

    TABLE 8: DIFFERENTIAL PRESSURE DEVICE OPTIONS

    Code Description

    PM Visual indicator with thermal lockout

    DM Visual indicator with no thermal lockout

    LL Electrical switch (SPDT) with 6" leads

    TL Electrical switch with DIN connector

    ML TL type switch with matching wiring cap

    SL Electrical switch with MS receptacle

    PL Same as PM but with plastic body

    DL Same as DM but with plastic body

  • Copyright Pall Corporation Visit us on the Web at www.pall.com

  • 7400 Series Spin-On Filter Assemblies

    Description

    Flows to 35 gpm (125 L/min) Pressures to 250 psi (17 bar) Port sizes: 3/4" and 1"

    Specifications

    Features

    Optional Differential Pressure Devices Full Flow Fast Response Bypass Valve Gasket Seal Spin-On Canister Optional Anti-Back Flow Valve (not shown). Prevents drainage of reservoir or lines where filter is

    mounted below fluid level Mounting Surface Gray Cast Iron Head O-Ring Seal Ultipor III Element

    Maximum Acceptable Working Pressure: 250 psi (17 bar) Fatigue Pressure Rating: 250 psi (17 bar) (60,000 cycles 0-250 psi) Typical Burst Pressure: 400 psi (28 bar) Temperature Range: Nitrile seals -20F to 225F (-29C to 107C) Fluorocarbon seals -20F to 250F (-29C to 120C) 140F (60C) maxim

Recommended

View more >