nanotech waterproofing products catalogue newecoscape-ltd.com/wp-content/uploads/2018/03/... ·...

Aquastop Nanoflex®

- Category: Inorganic Mineral Products - Class: Nanotech waterproofing products - Rating: Eco 3

0049

7Aqu

asto

p N

anofl

ex®

Cod

e: F

899

2014

/05

EN

LAYING RANGE / Nanotech waterproofing products for substrates

Certified, eco-friendly, breathable, anti-alkali and chlorine-resistant, mineral membrane for the flexible waterproofing with high levels of adhesion and durability of substrates before laying with adhesives, ideal for use in GreenBuilding. Single-component with low CO2 emissions and very low volatile organic compound emissions. Recyclable as an inert material at the end of its life.

Aquastop Nanoflex® develops a smooth, fluid mixture that can be adjusted by varying the amount of water in order to obtain optimal workability for the particular site conditions, guaranteeing maximum adhesion of the bonded system.

Aquastop Nanoflex®

3

®

Regional Mineral ≥

60

% Regional Mineral ≥

30

%

Recycled

≤ 250 g/ kg

IAQVOCIndoor Air Qualit

y

Low Emission

Recyclable

CO2 /kg emission

108 g

Very low VOC emissions

Can be recy-cled as inert

material

KERA

KOLL EASY PACK

S Y S T E M

* ÉMISSION DANS L’AIR INTÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions).

• Floors and walls, for internal and external use• Breathable• Crack-Bridging Ability• Specifically intended for laying ceramic tiles, natural

stone and glass mosaic using adhesives from the H40® range

• Suitable for overlaying• 30% better coverage than two-component systems• 20 kg paper bags with carrier handle• Nanotech technology which makes it completely water

repellent and gives permanent elasticity and high chemical stability

PRODUCT STRENGTHS

- Can be recycled as mineral inert material, avoiding waste disposal costs and environmental impact

- Single-component; avoiding the use of plastic cans reduces CO2 emissions and the need to dispose of special waste

ECO NOTES

GREENBUILDING RATING®

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

KERAKOLL® WATERSTOP SYSTEM is the brand behind AquaExpert systems, the state-of-the-art waterproofing systems for balconies, terraces and any surface whatsoever where ceramic tiles, natural stone and glass mosaic are to be laid. AquaExpert guarantees 100% water-resistant substrates and the highest possible chemical/physical compatibility ratio with cement-based adhesives that are suitable for laying the floor coverings, thereby ensuring the long life of the entire bonded system.Aquastop Nanoflex® eco-friendly membrane is used in the following AquaExpert systems: AQUAEXPERT 1 Flexible, high-adhesion and superior durability waterproofing system which is easy and fast to ap-

ply. Specifically intended for balconies, terraces and horizontal external surfaces that are small in size and with no expansion joints in the screed to be floored with ceramic tiles and natural stone. Guarantees water-resistance without the use of a reinforcing mesh.AQUAEXPERT 2 Flexible, high-adhesion and superior durability waterproofing system which provides greater shear strength. Specifi-cally intended for balconies, terraces and horizontal external surfaces of any size and with expansion joints in the screed to be floored with ceramic tiles and natural stone.

KERAKOLL® WATERSTOP SYSTEM

EN 1 2 0 0 4

G uaran teed

KERA

KOLL

WA TERSTOP SYSTEMAquaExpert

UseTerraces, balconies, horizontal surfaces and swimming pools on mineral screeds, monolithic cement-based screeds, existing floors covered with ceramic and marble tiles, dimensionally stable natural stone well-anchored to the substrate and clean, cement-based plasters/renders and cementitious mortars, aged concrete.

Do not useOn gypsum or anhydrite-based substrates without the use of eco-friendly Primer A Eco, water-based surface isolation, on metal or wood substrates, on bituminous sheeting, to waterproof exposed surfaces subject to foot traffic, on low-density screeds, on insulation layers on inverted roofs made with isolation panels or lightened materials.

AREAS OF USE

CO

NTRIBUTES TO

P O I N T S

NANOTECHKERAKOLLNANOINNOVATION

CM O1 PC O V E R A GEEN 14891

0049

7Aqu

asto

p N

anofl

ex®

Cod

e: F

899

2014

/05

EN

Preparation Prepare Aquastop Nanoflex® in a clean container by pouring in approximately ¾ of the water required. Gradually add Aquastop Nanoflex® to the container, mixing the paste from the bottom upwards with a low-rev (≈ 400/min) agitator. Add more water until the desired consistency is obtained. The mixture must be of smooth consistency and without any lumps. The amount of water to be added, indicated on the packaging, is an approximate guide. It is possible to obtain mixtures with a more or less fluid consistency, depending on the type of application.

ApplicationAquastop Nanoflex® should be applied with a smooth spreader on a previously prepared substrate. Apply the first coat about 1 – 2 mm thick, pressing down to ensure maximum adhesion to the substrate. Once hardened and after removing any surface condensation, apply the second coat of Aquastop Nanoflex®. Lay a continuous, even layer about 2-3 mm thick covering the substrate completely. When waterproofing with Aquastop AR1 mesh, submerge the reinforcing mesh fully in the first layer of freshly applied waterproofing product, pressing down with the spreader. The subsequent laying of the covering should be placed at least 24 hours after the last layer of H40® range eco-friendly mineral adhesive has been applied. when working in low temperatures and with high humidity, the waiting time be-fore laying will be longer. If rain falls on the product before it is fully hardened, check it is ready before applying the next coat/covering.

CleaningResidual traces of Aquastop Nanoflex® can be removed from tools with plain water before the product hardens.

INSTRUCTIONS FOR USE

AquaExpert 1 SystemWaterproofing for floor-wall joints – Supply and application of non-woven, alkali-resistant waterproof polypropylene tape with high adhesion, such as Aquastop 70 to be fixed with single-component, eco-friendly, breathable, anti-alkali and chlorine-resistant, mineral membrane with GreenBuilding Rating® Eco 3, such as Aquastop Nanoflex® by Kerakoll Spa. Substrate waterproofing – Certified supply and application of flexible, single-component, variable rheology, eco-friendly, breathable, anti-alkali and chlorine-resistant, mineral membrane with high levels of adhesion and durability of substrates before laying ceramic tiles and natural stone with adhesives, GreenBuilding Rating® Eco 3, such as Aquastop Nanoflex® by Kerakoll Spa.AquaExpert 2 SystemWaterproofing for floor-wall joints and fractionizing/expansion joints – Supply and application of waterproof polypropylene-coated non-woven polyethylene tape with high levels of adhesion, such as Aquastop 100, to be secured with eco-friendly mineral adhesive such as H40® by Kerakoll Spa.Substrate waterproofing – Certified supply and application of flexible, single-component, variable rheology, eco-friendly, breathable, anti-alkali and chlorine-resistant, mineral membrane with high levels of adhesion and durability of substrates before laying ceramic tiles and natural stone with adhesives, GreenBuilding Rating® Eco 3, such as Aquastop Nanoflex® in which to embed alkali-resistant 10 mm x 10 mm reinforcing mesh, such as Aquastop AR1 by Kerakoll Spa.

ABSTRACT

Appearance light grey ready-mixed waterproofing product Apparent volumetric mass 1 kg/dm3 Mineralogical nature of inert material silicate - crystalline carbonate Shelf life ≈ 12 months in the original packaging in dry environmentPack 20 kg bags with handle Mixing water ≈ 5 – 6 l / 1 20 kg bag Viscosity ≈ 60,000 mPas · sec Specific weight of the mixture ≈ 1,5 kg/dm3 UNI 7121Pot life ≥ 1 hr Temperature range for application from +5 °C to +35 °C Minimum total thickness ≥ 2 mm Maximum thickness per layer ≤ 1,5 mm Waiting time between 1st and 2nd coat ≥ 6 hrs Waiting time before laying the covering* ≥ 24 hrs Interval before normal use ≈ 7 days / ≈ 14 days (permanent water)Working temperature from -20 °C to +90 °C Coverage ≈ 1,15 kg/m2 per mm of thickness Values taken at +23 °C, 50% R.H. and no ventilation. (*) Thickness and weather conditions may extend these times considerably.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in April 2014 (ref. GBR Data Report - 05.14); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

0049

7Aqu

asto

p N

anofl

ex®

Cod

e: F

899

2014

/05

EN

- Product for professional use- abide by any standards and national regulations- technological specifications and application information can be found in the AquaExpert Instructions- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 2353/11.01.02HIGH-TECHInitial adhesion ≥ 2 N/mm2 EN 14891–A.6.2Adhesion after contact with water ≥ 1 N/mm2 EN 14891–A.6.3Adhesion after heat ageing ≥ 2 N/mm2 EN 14891–A.6.5adhesion after freeze-thaw cycles ≥ 1 N/mm2 EN 14891–A.6.6Adhesion on contact with lime water ≥ 1,5 N/mm2 EN 14891–A.6.9Adhesion on contact with chlorinated water ≥ 0,8 N/mm2 EN 14891–A.6.7Water-resistance no penetration EN 14891–A.7Breathability (No. nanopores) ≥ 1 billion/cm2 ASTM E128Crack-Bridging in standard conditions ≥ 0,75 mm EN 14891–A.8.2Crack-Bridging at low temperatures (-5 °C) ≥ 0,75 mm EN 14891–A.8.3Containmnet of drinking water Suitable ARPA Cert. 016824/06/RE

Conformity CM 01P EN 14891Values taken at +23 °C, 50% R.H. and no ventilation.

PERFORMANCE

• It waterproofs any surface, old or new, damp or dry, cracked or subject to dimensional variations.

• It compensates for hygrometric shrinkage and thermal deformation stress.

• It reduces on-site working times: waterproofing and laying of the coating without waiting, withstands foot traffic immediately

• Solves the problem of respecting substrate joints in staggered or diagonal laying (cuts in doorways)

PRODUCT STRENGTHS

Aquastop Green is a highly innovative Kerakoll creation. The membrane is a high-technology, multi-layer composite polymer system comprising:

• PA - hydrophobic PA fibres with high tensile strength to guarantee a superior and more evenly distributed available contact surface

• HDPE - waterproof and variable geometry HDPE structure to guarantee physical separation between the substrate and the flooring

• TNT - highly breathable sheet to guarantee passage of the vapour from uncured screeds or screeds with high residual humidity and to guarantee high levels of adhesion to the substrates

KERAKOLL PATENT

0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN


Anti-cracking waterproof membrane with high adhesion for balconies, terraces and horizontal surfaces before laying ceramic tiles or natural stone; creates a waterproof surface even when overlaid on substrates that are cracked, have not been perfectly cured or might contain vapour pressure due to residual substrate moisture content.

Aquastop Green revolutionises the world of underlying waterproofing, re-writing performance standards to allow applications that are impossible for mineral products.

Aquastop Green

n. 2246467filing date

20/06/2012

EURO

PEA N PA TENT

AQ

U

A STOP GREEN

CONTACTPOWER

+470%

ANTIFRACTURE

VAPOURDIFFUSION

UseFor internal and external use to waterproof, separate and compensate for vapour pressure prior to laying of ceramic tile and natural stone coatings for domestic, commercial, industrial uses (for example industrial kitchens, food industries, warehouses) and for street furniture (check that the size and thickness of the materials to be laid is suitable).Substrates:- screeds, including any that are cracked and not completely cured or with possible vapour pressure caused by residual humidity,- existing ceramic, marble floor tiles, natural stone floorings anchored to the substrate,- cured concrete,- fibre-cement and plaster-board panels anchored to the substrate.

AREAS OF USE

KERAKOLL WATERSTOP SYSTEM is the brand behind AquaExpert systems, the state-of-the-art waterproofing systems for balconies, terraces and any surface whatsoever where ceramic tiles, natural stone and glass mosaic are to be laid. AquaExpert guarantees 100% water-resistant substrates and the highest possible chemical/physical compatibility ratio with cement-based adhesives that are suitable for laying the floor coverings, thereby ensuring the long life of the entire bonded system.Aquastop Green nano-membrane is used in the following AquaExpert system:AQUAEXPERT 3

Anti-cracking, high-adhesion and superior durability waterproofing system which guarantees immediate laying of the coating material even on cracked substrates that may contain vapour pressure. Specifically intended for balconies, terraces and horizontal surfaces of any size with no fractionizing and expansion joints in the screed to be tiled with ceramic tiles and natural stone.


EN 1 2 0 0 4

G uaran teed

KERA

KOLL


0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN

STORAGEProtect the rolls from direct sunlight, heat sources and rain, both during storage in the warehouse and on site. When laying the sheets, protect them from sunshine until shortly before application.

PREPARATION OF SUBSTRATE

1 Check the mechanical performance and surface consistency of the laying substrate.

2 Check that old flooring is properly anchored and clean.

3 Restore the continuity of the screed by sealing cracks with a width > 1 mm: break the crack open mechanically, remove dust and debris and repair using Kerarep Eco.

4 The residual humidity level in the screed, when measured with a carbon hygrometer, must be less than 8%.

5 Check the levelness and the presence of suitable camber that will guarantee drainage via suitable drains. Fill in any irregularities in the substrate using a suitable finishing product.

Notes• Checking Residual Humidity. Application of the membrane can be carried out on screeds created using Keracem® Eco products 24 hours after the screed has

been laid (standard conditions); on traditional sand-cement screeds it is necessary to wait until the screed is strong enough to walk on and to carry out subsequent operations.

In the event of rain showers during the hours preceding laying of the membrane, check that the surface is dry and free from standing water. In the event of rain during the days preceding laying of the membrane, check that at least the top 1/4 of the screed is dry.

• Checking for damage. The membrane is capable of compensating for hygrometric shrinkage of the screed (movements ≤ 1 mm); this means it is possible

to lay the membrane even on uncured screeds and/or on screeds without a suitable network of fractionising joints. In the case of fractured screeds or floors or those with a network of fractionising-expansion joints application of the membrane means that the laying pattern of the new flooring is not bound by the layout of the joints in the substrate. Structural joints: always respect the entire width of any structural joints, cut the membrane and connect its edges to the structural joint.

SUBSTRATE WATERPROOFING

1 Clean the substrates of dust, oil and grease, loose debris or flaky parts, residues of cement, lime, plaster/render, or paint coatings.

2 Do not apply to substrates at a temperature > 35 °C (temperature of the substrate); when absorbent substrates (screeds, standard grain concrete, etc.) are exposed to strong sunlight, damp their surfaces, avoiding the accumulation of an excessive quantity of water.

3 Unroll the sheets and cut them to size, considering a space of approximately 5 mm between the sheets and the perimeter walls, stringcourses, protrusions, columns, pillars, architectural elements, drains, etc., and between one sheet and the next.

4 Apply H40® No Limits® adhesive using a suitable toothed spreader; lay a thin layer with the smooth side, pressing down heavily to achieve maximum adhesion to the substrate and regulate water absorption.


Do not useOn anhydrite-based substrates without the use of Primer A Eco professional, concentrated, water-based surface insulation, on bituminous sheeting, on exposed surfaces, on inverted roofs made with insulation panels or low-density screeds, and on roofs of residential spaces built without vapour barrier and insulation layers.

AREAS OF USE

2

433

1

54

321

3

11

10

6

8 9

755 Regulate the thickness by the tilt of the spreader, using the toothed part. Apply the adhesive to a surface area that will allow laying of the sheets within the open time indicated (check the state of the adhesive frequently). Avoid any build-up of adhesive, that might compromise the flatness of the sheets.

6 Position the sheets or unroll them onto the fresh adhesive, taking care they are flat and avoiding the formation of creases or bubbles.

7 Create joints approximately 5 mm in width between the sheets and the perimeter walls, stringcourses, etc., and between one sheet and the next.

8 Immediately press the sheets down onto the fresh adhesive using Aquaform R mixed with a bag of adhesive.

9 Check that the whole of the white unwoven fabric on the back of the membrane has been dampened; if necessary increase the amount of adhesive and press more carefully. Press properly to ensure that the membranes are taut.

10 Avoid getting fresh adhesive onto the roller, as this might compromise the surface of the sheets.

11 Lay the next sheet, aligning it with the preceding one and leaving a gap of approximately 5 mm between one sheet and the next; press immediately, paying particular attention to passage of the roller along the edges of the sheets.

Notes• The maximum length of membrane applicable is approximately 12 m; for longer sections, cut the membrane transversally and

leave a space of approximately 5 mm between one sheet and the next.

• If necessary, weight the edges down immediately after gluing.

WATERPROOFING OF INTERNAL AND EXTERNAL ANGLES

1 Seal the outer edges of the surface, starting from the corners. Cut a 20 cm strip of Aquastop 100 and cut halfway into it about halfway along the strip.

2 Fold the strip in half to create an internal corner and two overlapping edges.

3 Apply Aquastop Fix sealing agent both on the wall and on the membrane using a smooth spreader and taking care to fill in circular cavities.

4 Position the special piece on the fresh sealant. Press firmly and smooth over the tape to ensure it adheres perfectly, being careful not to wrinkle it.

5 Seal the overlap between the two bases using Aquastop Fix.

6 Remove any excess sealant that may have seeped out and check the adhesion of all the tape edges.

7 For external angles, create an angle as described above and fold it into an open external angle, then cut a strip of Aquastop 100 14 cm in length and cut out a square approx. 7x7 cm to create an “L” shaped insert.

8 Fix the insert created on the fresh sealant to connect the special piece glued previously; press down hard and smooth to guarantee total sealing and avoid the formation of wrinkles in the tape.

Notes• Clean the surface of the sheets carefully; check that the plaster/render in the perimeter strip is clean and consistent.


0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5

7 8

6

2

5

331

4

PERIMETER WATERPROOFING

1 Lay the sealant along the perimeter in the vicinity of the wall-floor corner joints: lay the sealant both on the wall and on the membrane in strips approximately 10 cm in width.

2 Position Aquastop 100 and smooth carefully.

3 Remove any excess Aquastop Fix that may have seeped out from under the tape, and take care to ensure the edges of the tape are fixed to the membrane. When waterproofing the wall-floor joint, lay about 10 cm Aquastop 100 over the special pieces.

Notes• Clean the surface of the sheets carefully; check that the plaster/render in the perimeter strip is clean and consistent.

WATERPROOFING BETWEEN THE SHEETS

1 Seal the longitudinal joints between one sheet and the next: apply the sealant using a smooth spreader for a width of at least 10 cm on either side along the joint (gap), taking care to fill in the cavities in the membrane completely.

2 Fix the tape on the fresh sealant.

3 Press down strongly and smooth to remove any wrinkles and to guarantee total sealing of Aquastop 100.

4 Remove any sealant that may have seeped out and make sure the edges of the tape are properly glued down.

5 Check frequently to ensure that the tape mesh is completely coated.

6 Seal the transversal joints (every 10-12 m) in the same way.

7 After laying, protect the surface of the membrane immediately from frequent foot traffic and direct abrasion using wooden planks or panelling.

Notes• Do not cover the tape with the sealant, to ensure that the subsequent covering applied will be properly level.

• Seal the entire perimeter and all the sheet-to-sheet contacts.

• Use Superflex Eco when fixing the tape on metals, plastics and stable woods.

WATERPROOFING OF THE THRESHOLD JOINT

1 Apply Aquastop Fix sealant under the threshold to fix the tape, which must have an asymmetrically positioned cross-section (“L” or “ ” position).

2 Apply the sealant and fix Aquastop 100 onto the fresh sealant, following the wall-floor joint.

3 Press firmly and smooth over to ensure the tape seals perfectly, being careful not to wrinkle it.

4 Join the threshold tape to the waterproofing of the wall-floor corner joint, overlapping the tapes by approximately 10 cm.


321

3

0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN

6

2

5

331

7

4

3

4

21

WATERPROOFING OF THE WALL-FLOOR CORNER JOINT IN THE PRESENCE OF BITUMINOUS SHEATH

1 Remove the upper half of the protective film and fix Aquastop BT to the wall on the clean, dry bituminous sheath. Fix the tape to the floor, following the wall-floor joint.

2 Bang on the tape to guarantee total adhesion to the substrates.

3 Smooth, avoiding the formation of any wrinkles (use tools that will not damage the tape).

4 During laying of the membrane, overlap the sheets on the horizontal part of Aquastop BT, creating a gap approximately 5 mm wide between the sheets and the wall.

5 To waterproof the corner, apply Aquastop Fix sealant vertically on Aquastop BT and horizontally on the adjacent portion of membrane, and position the Aquastop 100 tape.

Notes• Aquastop BT tape is recommended when connecting the membrane to metals, plastic materials, stable wood: clean the

substrates, removing any condensation.

JOINING THE WATERPROOFING LAYER TO AQUAFORM DRAINS

1 Lay Aquastop Fix on the black TNT connection surfaces of the AquaForm drains and on the adjacent surfaces to be connected .

2 Position the special pieces of Aquastop 100 cut to measure.

3 Press firmly and smooth over to ensure the tape seals perfectly, being careful not to wrinkle it. If necessary, use several pieces of tape until the drain has been completely sealed (black TNT totally covered).

WATERPROOFING: SPECIAL CASES

1 In cases where there is insufficient space for adhesion of the Aquastop 100 tape, seal using Nanosil Eco, reduce the gap between sheet and element to be sealed to 2–3 mm; wait until the H40® No Limits® adhesive has hardened and then proceed with sealing. Extrude an abundant quantity of the product and allow it to penetrate deeply, to guarantee complete filling of the gap.

2 Cure the seal with Nanosil Eco in the vicinity of thresholds, perimeter stringcourses, grills, drains, down spouts, through elements, railing posts and installations.

Notes• Protect the membrane from direct sunlight and heat for at least 12 hours.

• Protect from rain for at least 12 hours (the hardening of the Aquastop Fix sealant guarantees waterproofing of the system).


2

5

31

4

0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN

21

2

331 2

1 3

LAYING THE FLOOR

1 Apply a first layer of adhesive to fill in the circular cavities; using the smooth part of the spreader.

2 Adjust the thickness of the adhesive using a toothed spreader of a type suited to the size of tile. Lay the flooring with open joints, with gaps of a minimum width from 2 – 3 mm according to the size of the tile (UNI standard 11493 point 7.10.2).

3 Check that the entire back of the tile is impregnated, to guarantee the suitability of the adhesive system.

4 Grout the gaps using Fugabella® Eco 2-20.

5 Seal the elastic joints using Fugabella® Eco Silicone.

* If the flooring is expected to be laid more than 5-7 days after waterproofing, finish the surface of the membrane itself with H40® No Limits®. This finish has the aim of protecting the membrane from atmospheric agents and direct wear. Clean the surface thoroughly before applying the finish: removing dust, any condensation, residue from previous operations, and apply a layer of adhesive to fill the circular cavities, then cover the whole of the surface with an even layer of adhesive approximately 1-2 mm thick.

Notes• The floor can be laid immediately using H40® No Limits®; it is not necessary to wait. Take care not to compromise the adhesion

of the fresh sealant under the tapes.

• If the floor is not laid immediately, protect the finished surface from rain, direct sunshine and heat.

• Provide for elastic joints at least 5 mm in width to separate the floor from the vertical elements and between materials of different types; create a grid of movement joints measuring between 3x3 m and 4x2.5 m (UNI standard 11493 point 7.11.1.2) with particular attention to possible structural movements.

• Provide for structural joints along their entire length.

• The presence of the anti-fracture membrane allows laying patterns that are not restricted by the geometry and characteristics of the substrates.

• Lay the skirting boards so that they are raised with respect to the floor, being fixed to the wall only


5

1

4

32*

3

0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN

AcquaExpert 3 SystemWaterproofing of the substrate - Supply and laying of waterproof anti-cracking membrane with high adhesion even on cracked substrates and those with possible vapour pressure caused by residual humidity, specific for waterproofing of substrates prior to laying of ceramic and natural stone tiles, such as Aquastop Green by Kerakoll SpA. Apply H40® No Limits® adhesive gel by Kerakoll SpA, using a suitable toothed spreader. Lay the membrane on the layer of fresh adhesive and press it down using a roller such as AquaForm R by Kerakoll SpA filled with a bag of adhesive. Use a smooth spreader to apply a continuous thin layer of mineral sealant such as Aquastop Fix by Kerakoll SpA along the joints in the sheets. Lay the waterproof tape such as Aquastop 100 by Kerakoll SpA onto the fresh sealant.

Waterproofing the wall-floor joints - Supply and laying of waterproof polyethylene tape coated on both sides with polypropylene, such as Aquastop 100 by Kerakoll SpA. Apply an eco-friendly mineral sealant such as Aquastop Fix by Kerakoll SpA to the walls and floor using a smooth spreader, and fix the waterproof tape. Press firmly and smooth over to ensure the tape adheres perfectly, being careful not to wrinkle it. To ensure the water-resistance of internal and external corners, make special pieces of tape to fix with the sealant.

ABSTRACT

When laying the membrane on wood, metal, rubber, PVC, linoleum and fibreglass, use Superflex Eco. When laying the membrane as a separating, compensating and vapour releasing layer in internal applications, the sheets do not require sealing with Aquastop 100 tape.

SPECIAL NOTES

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in May 2015 2011; please note that additions and/or amendments to this information may be made over time by KERAKOLL Spa; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) ItalyTel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

ISO 9001CERTIFIEDIT10/0327

ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

- Product for professional use- abide by any standards and national regulations- avoid direct exposure to sunlight and sources of heat during the storage and in the installation phases on the building site- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

HIGH-TECH WHEN USED IN COMBINATION WITH H40® NO LIMITS® AND PORCELAIN TILES Resistance to strain parallel to the laying surface 1,8 N/mm2 UNI 10827 / EN 12004Resistance to strain parallel to the laying surface, laying in water 1,8 N/mm2 UNI 10827 / EN 12004Resistance to strain parallel to the laying surface, laying after heat 1,4 N/mm2 UNI 10827 / EN 12004Resistance to strain parallel to the laying surface, laying in frost/thaw 1,8 N/mm2 UNI 10827 / EN 12004 Compressive strength 38 N/mm2 Resistance to dynamic stress:- Robinson Test with porcelain tiles, thickness 10 mm no breakage(*) ASTM C 627 - classification extremely heavy and high impact loads Floor Tiling Guide in commercial and industrial buildings Impact noise damping (∆Lw) 9 dB UNI EN ISO 717-2 Values taken at +23 °C, 50% R.H. and no ventilation.(*) Steel wheels / total load 408 kg / 450 cycles

PERFORMANCE

Appearance composite polymeric membraneColour white / transparent / greenShelf life ≈ 24 months in a cool dry placeWarning Avoid direct exposure to sunlight and sources of heatWidth 1,15 ± 1 cm EN 1848-2length 20 m EN 1848-2Thickness ≈ 4 mm EN 1849Longitudinal elongation 20% DIN 53504 / ISO 254Transversal elongation 25% DIN 53504 / ISO 254Substrate residual humidity max 8% EN 10329


0059

7Aqu

asto

p Gr

een

Code

: P94

5 20

15/0

5 EN

• Internal, external

• It guarantees the same adhesion as eco-friendly mineral adhesives

• Paper bags with carrier handle

• Nanotech technology which makes it completely water repellent and gives high chemical stability

• Pre-mixed, easy-to-identify green mineral

PRODUCT STRENGTHS


ECO NOTES

Aquastop Fix - Category: Inorganic Mineral Products - Class: Nanotech waterproofing products for substrates - Rating: Eco 2



0060

3Aqu

asto

p Fi

x Co

de: F

751

2016

/01

UK


Certified, eco-friendly, mineral sealant for water-resistant, high-adhesion sealing, ideal for use in GreenBuilding. Single-component with very low volatile organic compound emissions. Recyclable as an inert material at the end of its life.

Aquastop Fix develops a fine mixture of extended workability and totally water repellent, guaranteeing the water-resistant adhesion of AquaExpert components and accessories.

Aquastop Fix

2

®


60


30

%

Recycled

≤ 250 g/ kg


y

Low Emission

Recyclable

Very low VOC emissions

Can be recycled as

inert material

NANOTECHKERAKOLLNANOINNOVATION W

ATERPROOF

100%

UseAquastop 100 sealing of perimeter joints and between adjacent sheets of Aquastop Green.

Balconies, terraces and horizontal external surfaces of any size

Do not useFor the bonding of ceramic tile. On bitumen, PVC, wood, polycarbonate, glass, plastic or metal substrates.

AREAS OF USE

KERAKOLL® WATERSTOP SYSTEM is the brand behind AquaExpert systems, the state-of-the-art waterproofing systems for balconies, terraces and any surface whatsoever where ceramic tiles, natural stone and glass mosaic are to be laid. AquaExpert guarantees 100% water-resistant substrates and the highest possible chemical/physical compatibility ratio with cement-based adhesives that are suitable for laying the floor coverings, thereby ensuring the long life of the entire bonded system.The eco-friendly sealant Aquastop Fix is used to seal the Aquastop 100 tape in perimeter joints and between adjacent sheets of Aquastop Green.


EN 1 2 0 0 4

G uaran teed

KERA

KOLL


KERA

KOLL EASY PACK

S Y S T E M

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in December 2015 (ref. GBR Data Report - 01.16); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 [email protected] - www.kerakoll.com

0060

3Aqu

asto

p Fi

x Co

de: F

751

2016

/01

UK

- Product for professional use- abide by any standards and national regulations- technological specifications and application information can be found in the Aquastop Green technical data sheet- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service 01527 578000 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R GEV-Emicode GEV certified 2111/11.01.02HIGH-TECHWater absorption after 30 min. 0,10 g EN 12808-5Water absorption after 240 min. 0,18 g EN 12808-5Water-resistance no penetration EN14891-A.7Values taken at +23 °C, 50% R.H. and no ventilation.

PERFORMANCE

Appearance sealing green pre-mixedApparent volumetric mass 1,35 kg/dm3

Mineralogical nature of inert material silicateShelf life ≈ 12 months in the original packaging in dry environmentPack 25 kg paper bags with carrier handleMixing water ≈ 5.6 ℓ / 1 x 25 kg bagSpecific weight of the mixture ≈ 1,65 kg/dm3 UNI 7121Grading ≈ 0 – 500 μmPot life ≥ 2 hrs Temperature range for application from +5 °C to +35 °CMaximum thickness obtainable ≤ 5 mmOpen time ≥ 20 min.Waiting time before laying covering immediateSetting time ≥ 6 hrsInterval before normal use ≈ 3 daysCoverage ≈ 0,8 kg/m2

Values taken at +23 °C, 50% R.H. and no ventilation.


Preparation of substratesIn general, substrates must be free from dust, oil and grease, dry and free from any rising damp, with no loose, flaky or imperfectly anchored parts such as residual traces of cement, lime and paint, which must be totally removed.

PreparationPrepare Aquastop Fix in a clean container, first of all pouring in a quantity of water equal to approximately ¾ of the amount required. Gradually pour Aquastop Fix into the container, mixing the paste from the bottom upwards with a low-rev (400/min.) electrical mixer. Add more water until the desired consistency is obtained. The mixture must be of smooth consistency and without any lumps. The amount of water to be added, indicated on the packaging, is an approximate guide. Adding extra water does not improve the workability of the eco-friendly sealant but may cause shrinkage in the plastic phase of drying and result in less effective final performance with a reduction in compressive and shear strength and adhesion to the substrate.

ApplicationPerimeter joints: apply the eco-friendly sealant Aquastop Fix on the wall and on the Aquastop Green membrane with a smooth trowel by filling in the hollow circular ribs for around 10 centimetres in width and apply Aquastop 100 on the fresh sealant by following the wall-floor joint. Press firmly and smooth over to ensure the tape seals perfectly, being careful not to wrinkle it.Joints between adjacent sheets: apply the eco-friendly sealant Aquastop Fix along the joints with a smooth trowel for at least 20 centimetres in width by filling in the hollow circular ribs and leaving a thin, even layer. Fix Aquastop 100 to the fresh sealant, following the joint between sheets. Press firmly and smooth over to ensure the tape seals perfectly, being careful not to wrinkle it.

The subsequent laying of the coating can be carried out immediately. If rain falls on the product before it is fully hardened, check the adhesion of Aquastop 100 tape carefully.

CleaningResidual traces of Aquastop Fix can be removed from tools with plain water before the product hardens.


Aqua

stop

Nan

osil

Code

: F79

2 20

17/1

0 EN

Eco-friendly rigid neutral silane sealant for waterproof sealing of hydraulic and electric systems, through elements and construction elements in pools and in AquaExpert systems, ideal for GreenBuilding. With reduced solvent and with very low volatile organic compound emissions. Safeguards the health of both operators and the environment.

Aquastop Nanosil develops a high level of adhesion and permanent elasticity on absorbent and non-absorbent surfaces, guaranteeing the waterproofing of system passages even in the most critical space situations.

Aquastop NanosilLAYING RANGE / Preparation of the substrates

• Specific for pools with aggressive water

• High adhesion on all materials without using primer

• Non-corrosive, does not stain sills and kerbs in natural stone

PRODUCT STRENGTHS

- With reduced solvent content, safer on site use guaranteed

ECO NOTES

Aquastop Nanosil - Category: Organic Mineral products - Preparation of the substrates - Rating: Eco 4



UseInternally, externally and in pools to give waterproof sealing of hydraulic and electric systems, through elements and construction elements.Compatible materials:- plasters, finishing products, screed and mineral patches;- cement and concrete cast on site or prefabricated, concrete blocks;- metals (steel, copper, bronze, brass, …);- plastic materials (PE, PPE, ABS, fibreglass, ...);- wood, glass, ceramic and porcelain tiles, natural stone.

Do not useOn dusty or poorly cohesive surfaces; on bituminous surfaces or those exuding oil, solvents or plasticizers; on substrates that are saturated with damp or subject to continual moisture rising or to waterproof leaks in specific points; for visible seals; for elastic sealing of expansion joints.

AREAS OF USE

KERAKOLL WATERSTOP SYSTEM is the brand behind AquaExpert systems, the state-of-the-art waterproofing systems for balconies, terraces and any surface whatsoever where ceramic tiles, natural stone and glass mosaic are to be laid. AquaExpert guarantees 100% water-resistant substrates and the highest possible chemical/physical compatibility ratio with cement-based adhesives that are suitable for laying the floor coverings, thereby ensuring the long life of the entire bonded system.Aquastop Nanosil sealant is used in all AquaExpert systems to waterproof in critical conditions where the limited space prevents application of Aquastop tape (undersills, perimeter stone kerbs, through handrails and guttering,

waterspout protection grilles, etc.).


EN 1 2 0 0 4

G uaran teed

KERA

KOLL



30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Very low VOC emissions Solvent-free

No environmental hazard rating

Non-toxic and non-hazardous

4

®

Preparation of substratesSubstrates must be compact, smooth, free from dust, oil and grease, with no loose and inconsistent debris. Sand and dust down metals and plastic materials, completely remove paints, varnishes and fine finishing coats. The substrate must be stable, non-deformable and with no cracks. The elements to be sealed must first be mechanically anchored to the substrate or embedded firmly in the casting concrete.

PreparationAquastop Nanosil is ready-to-use. After cutting the conical nozzle of the cartridge, cut the spout at an angle of 45° to suit the width of the seal to be realized and screw it onto the cartridge. Insert the tube of silicone into the appropriate manual or air-powered applicator gun, start sealant extrusion and fill the joint.

ApplicationThe extruded product must be compressed and made to penetrate in depth in order to give optimum adhesion and guarantee waterproofing; the use of a metal or plastic scraper dipped in soapy water is recommended.

CleaningResidual sealant can be cleaned using Slc® Eco Diluente 01, eco-friendly single-component thinner with no environmental hazard rating, or with normal solvents (e.g. nitro solvent).


Do not use in completely closed areas as the product will polymerise in atmospheric humidity.

SPECIAL NOTES

Elastic, waterproof sealing of hydraulic and electric systems, through elements and construction elements will be carried out using eco-friendly, neutral organic silane sealant, GreenBuilding Rating® Eco 4, such as Aquastop Nanosil by Kerakoll Spa. Substrates must be compact, smooth, clean and with no loose debris. Sand and dust down metals and plastic materials.

ABSTRACT

Appearance Grey thixotropic pasteSpecific weight 1,6 kg/dm3

Chemical nature neutral cross-linked silane sealantShelf life ≈ 18 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack 290 ml cartridgeJoint minimum width ≥ 5 mmJoint max. width ≤ 25 mmTemperature range for application from +5 °C to +40 °CCuring time ≥ 25 min.Reticulation ≈ 2.5 mm / 24 hrsCoverage ≈ 10 m (joint 5x5 mm) with 1 cartridge (290 ml)Values taken at +23 °C, 50% R.H. and no ventilation.


Aqua

stop

Nan

osil

Code

: F79

2 20

17/1

0 EN

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in September 2017 (ref. GBR Data Report - 10.17); please note that additions and/or amendments to this information may be made over time by KERAKOLL Spa; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.



ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

Aqua

stop

Nan

osil

Code

: F79

2 20

17/1

0 EN

- Product for professional use- abide by any standards and national regulations- use at temperatures between +5 °C and +40 °C- do not use in completely closed areas- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1 plus GEV-Emicode GEV Certified 7003/11.01.02HIGH-TECHShore hardness A 80 ISO 37-1Break strength ≈ 4,3 N/mm2 DIN 53504Working temperature from -40 °C to +100 °CValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Aquastop Flex - Category: Inorganic Mineral Products - Class: Organic Waterproofing Products - Rating: Eco 3


• High adhesion to absorbent and non-absorbent substrates

• High compatibility with cement-based adhesives in the H40® range

• High workability

• Floors and walls, for internal and external use

• Suitable for overlaying

• Constant Crack Bridging even at low temperatures

• Suitable for the containment of water under positive-negative thrust

GREENBUILDING RATING® PRODUCT STRENGTHS


- With very low volatile organic compound emissions

ECO NOTES

UseWaterproofing of balconies, terraces, swimming pools, kitchens, saunas, Turkish baths, showers before coverings in ceramic, glass mosaic and stone materials are laid. Suitable for waterproofing of foundations, hoistway pits, basement areas, exterior foundation elements, including those with negative hydrostatic thrust, parts of concrete structures, elements and surfaces.

Suitable for:- cement-based screeds- mineral screeds made using hydraulic binders such as Keracem® Eco- old flooring that is dimensionally stable and anchored to a ceramic substrate- marble tiles, natural stone- concrete elements- cement plasters and cement-based mortars

Suitable for gypsum substrates, anhydrite-based screeds, gypsum and anhydrite-based levelling and self-levelling products, after application of Primer A Eco eco-friendly, water-based surface insulation.

Do not useDo not use on metal or wooden substrates, on bituminous coverings, to waterproof surfaces that are to be walked on and uncovered swimming pools, on lightened screeds.

AREAS OF USE


Aqua

stop

Fle

x Co

de: F

115

2015

-11

UK

Certified, eco-friendly, two-component, anti-alkali and chlorine-resistant, mineral membrane for flexible waterproofing with high levels of adhesion and durability of substrates before laying with adhesives, ideal for use in GreenBuilding. Low CO2 emissions and very low volatile organic compound emissions, recyclable as an inert material at the end of its life.

Aquastop Flex creates a water-resistant layer on balconies, terraces, swimming pools and shower cabinets before laying ceramic tiles, even over existing coverings, doing away with the need for costly demolition work.

Aquastop Flex

3


60


30

%

Recycled

≤ 250 g/ kg


y

Low Emission

Recyclable

CO2/kg emission

217 gVery low VOC

emissionsCan be

recycled as inert material

CO

NTRIBUTES TO

P O I N T SCM O2 P

EN 14891

Aqua

stop

Fle

x Co

de: F

115

2015

-11

UK

Preparation of substratesThe substrate must be perfectly cured and dry, solid (i.e.free of weak or easily removable parts) and free from oil, grease and paint. Check that the concrete contains no traces of parting compound. When working on weakened parts, when parts of the substrate are missing and also in the case of gravel beds, the substrate must be restored with suitable repair mortars. Uneven areas must be corrected with suitable smoothing and finishing products. On ceramic substrates all traces of surface treatments such as wax and oil must be removed. The most suitable cleaning methods are sandblasting, mechanical scarification or washing with detergents and jet washing. Before application damp the surface of absorbent substrates, without letting any build-up of water occur.When waterproofing monolithic tanks or swimming pools grout the spacer holes using Kerabuild® Eco Epobond, epoxy organic mineral system, and use Kerabuild® Eco R4 Tixo mineral mortar to create rigid connection shells in horizontal and vertical corners and perform any levelling operations that may be necessary.On terraces and balconies expansion joints must be provided in the substrate.For waterproofing of corners and expansion joints with Aquastop 120 applied using Aquastop Flex. For external and internal angles and for water and drainage pipeline crossings use special pre-formed pieces applied using Aquastop Flex.

PreparationAquastop Flex is prepared by mixing component A with component B (preset ratio of 3 : 1 in the packaging). The two components should be mixed with a suitable low-rev electrical mixer for approximately 2 minutes until a mixture with a homogenous consistency is obtained. Pour the latex into a clean recipient and gradually add the powder during the mixing operation. Leave the mixture to rest for approximately 2 minutes to allow the co-polymer to become completely dispersed and mix again for approximately 20 seconds before use.

ApplicationAquastop Flex should be applied to a previously prepared substrate by spreader, roller or spraying. When waterproofing, apply the first coat and when the product has hardened apply the second coat in a direction transversal to the previous coat, making sure that the whole surface is completely covered to a minimum total thickness of 2 mm. Subsequent laying of the coating must take place at least 24 hours after application of the last coat, using adhesives from the H40® Eco range, in the case of low temperatures and high humidity levels the waiting time before laying must be extended.

CleaningResidual traces of the product can be removed from tools with plain water before the product has hardened.


Special applications:Walls waterproofed with Aquastop Flex: a wide rough coat must be applied when applying plaster.Use Aquastop 120 applied with Aquastop Nanoflex to waterproof structural joints.

SPECIAL NOTES

Appearance Part A light ready-mixed compound / Part B white latexPack Part A 24 kg bag / Part B 8 kg canMixing ratio Part A : Part B = 3:1Shelf life ≈ 12 months in the original packaging in dry environmentWarning Liquid: protect from frost, avoid direct exposure to sunlight and sources of heatPot life ≥ 1 hrTemperature range for application from + 5 °C to + 30 °CMinimum thickness per coat ≈ 1 mmMinimum thickness after two coats ≈ 2 mm DIN 19195-4Maximum thickness obtainable by coat ≈ 3 mmMaximum thickness obtainable ≤ 6 mmWaiting time between 1st and 2nd coat ≤ 24 hrsWaiting time before laying ≥ 24 hrsInterval before normal use for swimming pools and water-containment tanks ≈ 14 daysSpecific weight of mixture ≈ 1,67 kg/dm3 UNI 7121Coverage ≈ 1,6 kg/m2 per mm of dry thicknessValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.


The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in November 2015 (ref. GBR Data Report - 11.15); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 [email protected] - www.kerakoll.com

Aqua

stop

Fle

x Co

de: F

115

2015

-11

UK

- Product for professional use- abide by any standards and national regulations- do not add water, other binders or different additives to the mixture- protect surfaces from sunshine, wind, rain, frost and foot traffic- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service 01527 578000 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV Certified 5023/11.01.02HIGH-TECHInitial adhesion ≥ 1,5 N/mm2 EN 14891–A.6.2Adhesion after contact with water ≥ 0,7 N/mm2 EN 14891–A.6.3Adhesion after heat ageing ≥ 1,3 N/mm2 EN 14891–A.6.5adhesion after freeze-thaw cycles ≥ 0,7 N/mm2 EN 14891–A.6.6Adhesion on contact with lime water ≥ 0,8 N/mm2 EN 14891–A.6.9Adhesion on contact with chlorinated water ≥ 0,7 N/mm2 EN 14891–A.6.7Water-resistance no penetration EN 14891–A.7Crack Bridging in standard conditions ≥ 0,75 mm EN 14891–A.8.2Crack Bridging at low temperatures (-5 °C) ≥ 0,75 mm EN 14891–A.8.3Containmnet of drinking water Suitable ARPA Certified 016824/06/REConformity CM O2P EN 14891Values taken at +23 °C, 50% R.H. and no ventilation.

PERFORMANCE

• Suitable for subsequent laying of ceramic tiles, porcelain tiles and natural stone using mineral adhesives

• High elasticity and chemical stability

• It can be easily applied with a spreader or roller to any substrate

PRODUCT STRENGTHS

- Formulated with locally-sourced minerals meaning lower green-house gas emission during transportation

- Water-based, limits the risk of loads that could be harmful and dan-gerous to the environment during storage and transportation

- Improved on-site safety guaranteed

ECO NOTES

UseWaterproofing of smooth, compact and absorbent substrates before laying ceramic coverings with adhesives.Compatible adhesives:- mineral adhesives and mineral adhesives with SAS technology - single-component and two-component organic mineral adhesives- cement-based, water-dispersed, reactive-epoxy and polyurethane two-component adhesives

For internal use. Concrete flooring, compact and smooth cement-based screeds, prefabricated or fresh concrete castings, gypsum, plasterboard and gypsum brick walls, cement-based plasters and finishing products and cement-lime mortar.

Do not useDo not use in external applications, on wet surfaces or substrates subject to moisture rising; in environments where water is always present, baths, swimming pools and tanks.

AREAS OF USE

Nanodefense® Eco - Category: Organic Mineral Products - Class: Nanotech waterproofing products for substrates - Rating: Eco 5




0015

4Nan

odef

ense

® E

co C

ode:

F79

3 20

14/0

8 EN

Certified, eco-friendly, organic, water-based, mineral waterproofing product for absorbent substrates in damp environments, ideal for use in GreenBuilding. Single-component with very low volatile organic compound emissions. Safeguards the health of both operators and the environment.

Nanodefense® Eco develops total water-resistance under positive thrust guaranteeing the protection of absorbent substrates or those subject to damp, or in constantly humid environments.

Nanodefense® Eco

5

®


30


y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Natural mineral content

52%

Very low VOC emissions Solvent-free



CO

NTRIBUTES TO

P O I N T S

* ÉMISSION DANS L’AIR INT ÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions).

Preparation of substrates Substrates must be compact, smooth and absorbent, free from dust, oil and grease, free from moisture rising, with no loose and incon-sistent debris. Varnishes and paints must be removed completely. The substrate must be stable, non-deformable and with no cracks. Plasters with a gypsum base must present a residual humidity ≤ 1% and screeds with an anhydrite base ≤ 0.5%, both of which should be measured with a carbide hygrometer. Check for traces of thin finishing, that would interfere with the subsequent laying of heavy surface coverings such as ceramic tiles.


0015

4Nan

odef

ense

® E

co C

ode:

F79

3 20

14/0

8 EN

Preparation Nanodefense® Eco is ready-to-use and does not need any preparation. In any case, before use it is advisable to remix the product inside the pack to ensure the mixture is of an even consistency. Any excess waterproofing product can be kept for later use by putting the lid back on the packaging.

ApplicationApply a fine, uniform film, preferably using a short bristle, synthetic fibre roller, a steel spreader or brush. When applied with a roller or brush, wait until the first coat has hardened before proceeding with the second one (≈ 1 hr depending on the absorbency level of the substrate and temperature) in order to ensure waterproofing. Nanodefense® Eco is ready-to-use and does not need any preparation. Angles and hydraulic couplings must be joined respectively using a non-woven polypropylene tape with Aquastop 70 waterproof treat-ment and relative accessories applied directly with Nanodefense® Eco.

CleaningNanodefense® Eco can be removed from tools and other surfaces by washing them using water before the product hardens or with solvents once hardened.


On highly absorbent substrates, apply a base coat by diluting Nanodefense® Eco with water depending on substrate absorption (max 5%). After this, apply the second undiluted coat using a steel spreader or roller to ensure the watertightness of the surface. If necessary, Aquastop AR1 special reinforcing mesh made of alkali-resistant glass fibre can be inserted, followed by a further coat of Nanodefense® Eco.

SPECIAL NOTES

The certified waterproofing of damp environments, kitchens, bathrooms, shower cabinets and saunas before laying ceramic and por-celain tiles, marble or natural stone will be done using a single-component, ready-to-use, eco-friendly, organic, mineral, solvent-free waterproofing product, GreenBuilding Rating® Eco 5, such as Nanodefense® Eco by Kerakoll Spa, to be applied with a roller or steel spreader with coverage of 1.5 kg/m2.

ABSTRACT

Appearance Light blue pasteSpecific weight ≈ 1,44 kg/dm3

Chemical nature co-polymers dispersed in waterShelf life ≈ 12 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack 20 / 15 / 5 kg bucketsViscosity ≈ 1100000 mPa · s, rotore 93 RPM 0,5 Brookfield methodTemperature range for application from +5 °C to +35 °CDilution for base coat ≈ 5%Minimum thickness per coat ≈ 1 mmMinimum dry thickness per coat ≈ 500 µmWaiting time between 1st and 2nd coat ≈ 1 hrWaiting time before laying:- min. ≥ 2 hrs- max ≤ 48 hrsCoverage ≈ 1,5 kg/m2

Values taken at +23 °C, 50% R.H. and no ventilation.


The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in November 2013 (ref. GBR Data Report - 12.13); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com


ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

0015

4Nan

odef

ense

® E

co C

ode:

F79

3 20

14/0

8 EN

- Product for professional use- abide by any standards and national regulations- do not apply Nanodefense® Eco as an external waterproofing covering- use at temperatures between +5 °C and +35 °C- Nanodefense® Eco is a product dispersed in water solution: hence, it should be stored and transported at temperatures of more than

+5 °C- apply the subsequent coat only when the previous one is perfectly dry- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1 plus GEV-Emicode GEV certified 2134/11.01.02HIGH-TECHWater-resistance ≥ 3 bar DIN 1048Permeability to water vapour µ after 28 days ≥ 20000 Cert.173379 Inst. Giordano

Water absorption after 28 days ≤ 5% UNI 8202/22Adhesion to concrete after 28 days ≥ 1 N/mm2 EN 1542Tensile strength after 28 days:- adhesives Class C1 ≥ 0,5 N/mm2 EN 1348- adhesives Class C2 ≥ 1 N/mm2 EN 1348Ultimate elongation after 7 days ≥ 90% DIN 53 504Crack bridging ≥ 1,5 mm ASTM C 1305Working temperature from -40 °C to +90 °CConformity CSTB 13/12-1142

Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

• Single-component, water-based, ready-to-use

• Breathable

• Non-slip

• Specifically intended to protect Aquastop Nanoflex® membrane

• Suitable to apply with a roller

• Suitable for the subsequent overlaying of ceramic tiles using adhesives from the H40® Eco range

PRODUCT STRENGTHS

- Formulated with locally-sourced minerals meaning lower greenhouse gas emission during transportation

- Improved on-site safety guaranteed

ECO NOTES

UseTerraces, balconies, flat roofs, walkways and horizontal surfaces waterproofed with Aquaexpert 1, Aquaexpert 2 or cement-polymer products left in view and subject to possible light foot traffic, designed for residential use; concrete and reinforced concrete elements as a protective agent to control damp.

Do not useOn non-waterproofed substrates; on surfaces subject to frequent and/or heavy traffic; on surfaces subject to road traffic; for water retention; on tar, bituminous or PVC sheeting; on flat roofs without suitable vapour barrier systems; when high levels of acid and alkaline resistance is required.

AREAS OF USE

Aquastop Traffic - Category: Organic Mineral Products - Class: Nanotech waterproofing products for substrates - Rating: Eco 3




0070

5Aqu

asto

p Tr

affic

Cod

e: P

948

2015

/05-

EN

Eco-friendly, water based, flexible organic mineral covering for non-slip protection of Aquastop Nanoflex® membrane, ideal for use in GreenBuilding. Single-component with very low volatile organic compound emissions, respects the environment and the health of workers; best spreader workability for protective finishing of waterproofed substrates in AquaExpert 1 and AquaExpert 2 systems subject to light foot traffic.

Aquastop Traffic provides for non-slip protection of the waterproofing membranes, guaranteeing durability and maximum resistance to atmospheric agents.

Aquastop Traffic

3

®


30


y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Natural mineral content

52%



* ÉMISSION DANS L’AIR INT ÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions).

Preparation of substratesThe waterproofing surface must be unbroken, compact, well anchored, free from dust and grease, dry, with no flaky parts or surface condensation.


EN 1504-2(C)

CO

NTRIBUTES TO

P O I N T S

MC2.3

METHODEN 1504-2

PR5.1

METHODEN 1504-2

IR8.3

METHODEN 1504-2

PI1.3

METHODEN 1504-2

Protection of surfaces destined for residential foot traffic waterproofed using AquaExpert 1 or 2 systems or cement-polymer products. Supply and laying of eco-friendly, breathable, non–slip, flexible organic mineral covering, ready-to-use and water based, GreenBuilding Rating® Eco 3, such as Aquastop Traffic by Kerakoll Spa.

ABSTRACT

Appearance Grey pasteChemical nature co-polymers dispersed in waterShelf life ≈ 18 months in the original packagingWeight of the mixture ≈ 1,600 kg/dm3

Warning Protect from frost, avoid direct exposure to sunlight and sources of heatPack 10 kg bucketsTemperature range for application from +10 °C to +35 °CLimit conditions for drying +10° C – 50% RHWait before application of second coat ≈ 4 hrs (+23 °C – 50% RH) ≈ 12 hrs (+10 °C – 50% RH)Minimum thickness when dry ≈ 0,4 mmCoverage ≈ 0.700 kg/m2 total (2 coats)Values taken at +23 °C, 50% R.H. and no ventilation.


0070

5Aqu

asto

p Tr

affic

Cod

e: P

948

2015

/05-

EN

Routine maintenance: to clean, use the water-based detergent Slc® Eco Silopark, an eco-friendly floor and surface cleaning soap. Suitably diluted according to the indications on the packaging.Extraordinary maintenance: to restore aesthetic and functional continuity following wear, clean carefully and then apply Aquastop Traffic using a spreader or roller (in the latter case the product can be diluted approximately 15% with water).

SPECIAL NOTES

PreparationAquastop Traffic is ready-to-use. Before use it is advisable to remix the product inside the packaging to ensure the mixture is of an even consistency. The unused product can be kept for later use by putting the original lid back on the container.

ApplicationAquastop Traffic is applied using a smooth spreader, pressing down hard onto the substrate in order to ensure maximum adhesion to the support; when the product has hardened check adhesion of the first coat and then apply a second coat totally covering the substrate. Apply the product, in two coats, over the entire surface, including the wall joints. The second coat can be applied using a short bristle roller after diluting if necessary with water (max. 15% by weight) provided the total weight of product applied per m2 is guaranteed.The product (water emulsion) hardens by evaporation of the water it contains, so that drying times are dependent on the temperature and relative humidity during the hours following application. Horizontally laid product that is not perfectly dry risks being washed away by rain or compromised by the formation of condensation.

Drying times according to ASTM D 5895-03:Standard test for drying during film formation of organic coating

Test thickness:0.400 mm Test thickness:0.400 mm

CleaningAquastop Traffic can be removed from tools and other surfaces by washing them using water before the product hardens.


RELATIVE HUMIDITY: 50%Temperature (°C) Dry Time

25 ≈ 75 min20 ≈ 90 min15 ≈ 2 hrs10 ≈ 2.5 hrs5 > 4 hrs

RELATIVE HUMIDITY: 85%Temperature (°C) Dry Time

25 ≈ 3 hrs20 ≈ 4 hrs15 ≈ 5 hrs10 > 8 hrs5 > 12 hrs

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in April 2015 (ref. GBR Data Report - 05.15); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.



ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

- Product for professional use- abide by any standards and national regulations- avoid direct exposure to sources of heat during the storage- follow the indications relating to product drying with great care (risk of rain)- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - [email protected]

WARNING

HIGH-TECHResistance to sliding:- leather on dry surface 0,70 Ministerial Decree No. 236 of 14/06/89 required value > 0.40- rubber on wet surface 0,73 Ministerial Decree No. 236 of 14/06/89 required value > 0.40Non-slip properties:- surface description rough DIN 51130 06/2004- total angle of acceptance 8,8° DIN 51130 06/2004- classification R9 BGR 181-10/2003Resistance to Abrasion loss of weight < 3000 mg EN ISO 5470-1 mole H22 1000 cicli 1000 gPermeability to water vapour Class I - SD < 5 m (permeable) EN 7783-1 EN 7783-2CO2 permeability SD > 50 m EN 1062-6Capillary absorption and water permeability w < 0,1 kg/m2 h0,5 EN 1062-3Impact resistance Class I EN ISO 6272-1Adhesion to concrete > 1.5 N/mm2 (traffiking) EN 1542Crack bridging class A2Tensile adhesion to Aquastop Nanoflex® > 1,2 N/mm2 UNI EN ISO 527Accelerated UV ageing no chalking ASTM G 154-06Conformity PI - MC - PR - IR EN 1504-2 (C)Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

0070

5Aqu

asto

p Tr

affic

Cod

e: P

948

2015

/05-

EN

nanotech waterproofing products catalogue newecoscape-ltd.com/wp-content/uploads/2018/03/... ·...

Documents