mx2 training program 04d material velocity
TRANSCRIPT
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 1/7
Material Velocity
OmniScan MX2 Training Program
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 2/7
2
OmniScan MX2 Training – Material Velocity Overview
The only component material parameter that is
required for the phased array calculator is thevelocity of sound for shear wave and\or
longitudinal wave transmission.
The OmniScan MX2 software contains a
dataase with common material types and their
velocities. The material type and shear\longitudinal are
normally selected during the wi!ard group
creation as part of the setup process.
"ustom velocities can e entered manually as
needed in the #T settings su menu and can emeasured using the velocity caliration wi!ard.
The material velocity must e $nown prior to
focal law creation. The velocity cannot e
modified in the MX2 without recreating the focal
laws.
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 3/7
3
OmniScan MX2 Training – Material Velocity – Angle Deviation
%iven the same eam parameters& materials will have slightly different
velocity for each angle. 'or shear wave eams in ()(* caron steel etween )+,) degrees there
is less than -) meters per second of velocity deviation. 'or shear wave eams in ()(* caron steel etween -+/) degrees
there is less than (- meters per second deviation.
This velocity range results in less than ( degree eam deviation and ismore accurate than the errors resulting from manual caliration.
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 4/7
4
OmniScan MX2 Training – Material Velocity – Angle Deviation cont.
'or those reasons& the MX2 uses one velocity for all focal laws within the group.
The velocity can e set independently for each group.
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 5/7
5
OmniScan MX2 Training – Material Velocity - Thickness
0uestion1
s the component material thic$ness required or eneficial for the focal lawcalculator3
4nswer1
5o. Only velocity is required for asic eam formation of steering and focus.The material component thic$ness is required for the s$ip lines and
trigonometry readings ut it is not an essential variale for the calculatorand it can e changed at any time efore or after caliration with no affecton the eam or caliration.
Selection of the focus point is often ased on thic$ness ut entered
separately in the software.
The OmniScan MX2 has a velocity measurement wi!ard that is e6plained ina later section.
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 6/7
6
OmniScan MX2 Training – Phase Array !alc"lator #eview
0uestion1
7hat are the essential parameters for the phased array
calculator3
(. 8roe parameters.
2. 7edge parameters.
9. Material Velocity
. :eam 'ormation.
4nswer1 4ll of the aove.
8/19/2019 MX2 Training Program 04D Material Velocity
http://slidepdf.com/reader/full/mx2-training-program-04d-material-velocity 7/7