moving message
TRANSCRIPT
-
7/31/2019 Moving Message
1/15
-
7/31/2019 Moving Message
2/15
To Display the time and Date information on the
LED MATRIX display
To display the messages that are sent through the
computer via serial port
To display the messages that are sent through the
mobile in the form of SMS
-
7/31/2019 Moving Message
3/15
MICROCONTROLLER
P89V51RD2
DRIVER
(SOURCECURRENT)
ROW
Serial
CommunicationRs232
DRIVER(SINK
CURRENT)
COLUMN
DECODER
4:16
LED
MATRIX8X8
(MULTIPLEXED)
GSM
MODEM
RTC
AND
EEPROM
I2C BUS
-
7/31/2019 Moving Message
4/15
-
7/31/2019 Moving Message
5/15
-
7/31/2019 Moving Message
6/15
-
7/31/2019 Moving Message
7/15
Source
Current
-
7/31/2019 Moving Message
8/15
-
7/31/2019 Moving Message
9/15
5 V Operating voltage from 0 to 40 MHz
64 KB of on-chip Flash program memory with ISP (In-System Programming) and
IAP (In-Application Programming)
1KB of data RAM
Supports 12-clock (default) or 6-clock mode selection via software or ISP
SPI (Serial Peripheral Interface) and enhanced UART
Four 8-bit I/O ports with three high-current Port 1 pins (16 mA each)
Three 16-bit timers/counters
Programmable Watchdog timer (WDT)
Eight interrupt sources with four priority levels
TTL- and CMOS-compatible logic levels
-
7/31/2019 Moving Message
10/15
The GSM unit contains a GSM module along with a GSM transmitter antenna.
The module functions according to its built and the antenna transmits the information
to the Base Station wherein this is exposed to further processing.
The GSM module that we are using in this unit is the SIMCOM SIM300 module.
It works on frequencies EGSM 900 MHz, DCS 1800 MHz and PCS1900 MHz.
SIM300 provide RF antenna interface with two alternatives: antenna connector and
antenna pad
SMS is one of the unique features of GSM compared to older analog systems.
The communication between the microcontroller and the GSM modem takes place
Serially at an baud rate of 9600bps.
-
7/31/2019 Moving Message
11/15
We use AT commands to control and program the SIMCOM
SIM300 module.
The main AT commands for using SMS are listed below.
AT Command for checking whether the GSM
Modem is properly working it returns a
O.K if it is working properly otherwiseerror is received
ATH Disconnect existing connection
AT+CMGS Send SMS command
AT+CMGR Read SMS Command
-
7/31/2019 Moving Message
12/15
FEATURES:
Real-Time Clock (RTC) Counts Seconds, Minutes, Hours,
Date of the Month, Month, Day of the week and year
56-Byte, Battery-Backed, General-Purpose RAM with Unlimited Writes
I2C Serial Interface
Programmable Square-Wave Output Signal
Automatic Power-Fail Detect and Switch Circuitry
Consumes Less than 500nA in Battery-Backup Mode with Oscillator Running
-
7/31/2019 Moving Message
13/15
Internally Organized 4096 x 8, 8192 x 8
2-Wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Clock Rate
Write Protect Pin for Hardware Data Protection
32-Byte Page Write Mode (Partial Page Writes Allowed)
-
7/31/2019 Moving Message
14/15
In Schools And Colleges
In Hospitals
In Temples
In Hotels
In Shops
-
7/31/2019 Moving Message
15/15