motherboard manual ga-n680sli-dq6 2

GA-N680SLI-DQ6Intel® CoreTM 2 Extreme quad-core / CoreTM 2 Quad /Intel® CoreTM 2 Extreme dual-core / CoreTM 2 Duo /Intel® Pentium® Processor Extreme Edition /Intel® Pentium® D / Pentium® 4 LGA775 Processor Motherboard

User's ManualRev. 200112ME-N680DQ6-2001R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household wasteand must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Motherboard

GA

-N680SLI-D

Q6

May. 08, 2007

Motherboard

GA-N680SLI-DQ6

May. 08, 2007

Copyright© 2007 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.The trademarks mentioned in the manual are legally registered to their respective companies.

NoticeThe written content provided with this product is the property of Gigabyte.No part of this manual may be reproduced, copied, translated, or transmitted in any form or by anymeans without Gigabyte's prior written permission. Specifications and features are subject tochange without prior notice.

Product Manual ClassificationIn order to assist in the use of this product, Gigabyte has categorized the user manual in thefollowing:

For quick installation, please refer to the "Hardware Installation Guide" included with theproduct.

For detailed product information and specifications, please carefully read the "Product User Manual".

For detailed information related to Gigabyte's unique features, please go to "TechnologyGuide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

Item Checklist ................................................................................................................. 6Optional Accessories ...................................................................................................... 6GA-N680SLI-DQ6 Motherboard Layout ......................................................................... 7Block Diagram ................................................................................................................ 8

Chapter 1 Hardware Installation ..................................................................................... 91-1 Considerations Prior to Installation .................................................................... 91-2 Feature Summary .......................................................................................... 101-3 Installation of the CPU and CPU Cooler ....................................................... 13

1-3-1 Installation of the CPU ......................................................................................... 131-3-2 Installation of the CPU Cooler ............................................................................ 14

1-4 Installation of Memory .................................................................................... 151-5 Installation of Expansion Cards ...................................................................... 171-6 Connecting the e-SATA Cable Kit ................................................................... 181-7 Setup of SLI (Scalable Link Interface) Configuration ....................................... 191-8 I/O Back Panel Introduction ........................................................................... 221-9 Connectors Introduction .................................................................................. 23

Chapter 2 BIOS Setup ................................................................................................ 35The Main Menu (For example: BIOS Ver. : FAa) ..................................................... 372-1 Standard CMOS Features ............................................................................. 392-2 Advanced BIOS Features .............................................................................. 412-3 Integrated Peripherals ..................................................................................... 432-4 Power Management Setup ............................................................................. 492-5 PnP/PCI Configurations ................................................................................. 512-6 PC Health Status ........................................................................................... 522-7 MB Intelligent Tweaker(M.I.T.) ....................................................................... 542-8 Load Fail-Safe Defaults ................................................................................... 572-9 Load Optimized Defaults ................................................................................. 572-10 Set Supervisor/User Password ..................................................................... 582-11 Save & Exit Setup ......................................................................................... 592-12 Exit Without Saving ....................................................................................... 59

- 5 -

Chapter 3 Drivers Installation ...................................................................................... 613-1 Install Chipset Drivers .................................................................................... 613-2 Software Applications ..................................................................................... 623-3 Driver CD Information .................................................................................... 623-4 Hardware Information ..................................................................................... 633-5 Contact Us ..................................................................................................... 63

Chapter 4 Appendix ................................................................................................... 654-1 Unique Software Utilities ................................................................................ 65

4-1-1 EasyTune 5 Introduction ..................................................................................... 654-1-2 Xpress Recovery2 Introduction ......................................................................... 664-1-3 Flash BIOS Method Introduction ........................................................................ 684-1-4 Configuring SATA Hard Drive(s) ........................................................................ 75A. nVIDIA® nForce 680i SLI Southbridge ........................................................................ 75B. GIGABYTE SATA2 Controller ...................................................................................... 854-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 974-1-6 Windows Vista ReadyBoost ............................................................................ 104

4-2 Troubleshooting ............................................................................................. 105

- 6 -

Item ChecklistIDE Cable x 1, FDD Cable x 1SATA 3Gb/s Cable x 4I/O Shielde-SATA Cable x 2SLI Bridge (GC-SLICON6) x 1Retention Bracket x 1

* The items listed above are for reference only, and are subject to change without notice.

Optional Accessories2 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-51/R)4 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-21/R)2 Ports IEEE 1394 Cable (Part Number: 12CF1-1IE008-01R)2 Ports SATA Power Cable (Part Number: 12CF1-2SERPW-01R)S/PDIF-IN Cable (Part Number: 12CR1-1SPDIN-01R)

- 7 -

GA-N680SLI-DQ6 Motherboard Layout

KB_MS CPU_FANLGA775

ATX

GA-N

680S

LI-D

Q6

CD_IN

F_AUDIO

MAINBIOS

SYS_FAN

FDD

PCIE_16_1

PCI1

F_US

B3

CODEC

GIGABYTESATA2

SPDIF_IN

IDEDD

RII1

DDRI

I2

DDRI

I3

DDRI

I4

BACKUPBIOS

PWR_

FAN

F2_1394F1_1394

TSB43AB23

PCIE_16_2

PCI3 BATTERY

SATAII1

F_PANEL

IT8718

Marvell88E8056

ATX_12V_2X

PWR_LED

AUDIO

LPT

USB_LAN2

COMA

R_1394

OPTICAL

CLR_

CMOS F_

USB2

F_US

B1

PCIE_8

SATAII0

SATA

II2

SATA

II4

SATA

II3

PCIE_12V

PCIE_1

CI

DUAL_LAN

USB_LAN1

SATA

II5

GSATAII2-0

GSATAII2-1

GIGABYTESATA2

GSATAII1-0

GSATAII1-1

TPM

PCI2

Marvell88E8052

Marvell88E1116

Marvell88E1116 nVIDIA®

nForce 680i SLINorthbridge

nVIDIA®

nForce 680i SLISouthbridge

NB_FAN

- 8 -

Block Diagram

LGA775Processor

CPU CLK+/-(333/266/200/133 MHz)

Host Interface

3 PCI

PCI Bus

3 IE

EE13

94a

TSB43AB23

DDRII 800/667/533 MHz DIMM

Dual Channel Memory

6 SATA 3Gb/s

10 USBPortsLin

e-Ou

tM

IC

CODEC

Line-

InSP

DIF

InSP

DIF

Out

Side

Spe

aker

Out

Cent

er/S

ubwo

ofer

Spe

aker

Out

Surro

und

Spea

ker O

ut

ATA33/66/100/133IDE Channel

PCIe CLK(100 MHz)

PCI Express x16

LAN1

RJ45 LPC BUS

Floppy

LPT Port

COM Port

PS/2 KB/Mouse

nVIDIA®

nForce 680i SLINorthbridge

Dual BIOS

PCI Express x8

IT8718

PCI Express x16

LAN2

RJ45

PCI CLK(33 MHz)

Marve

ll88

E111

6 x

2 nVIDIA®

nForce 680i SLISouthbridge

1 PCI Express x1

PCI Express Bus

4 SATA 3Gb/s

x 1

LAN

RJ45

GIGABYTESATA2 x 2

x 1

LAN

Marvell88E8056

Marvell88E8052

RJ45

PCIe CLK(100 MHz)

Hardware Installation- 9 -

English1-1 Considerations Prior to InstallationPreparing Your ComputerThe motherboard contains numerous delicate electronic circuits and components which canbecome damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, pleasefollow the instructions below:1. Please turn off the computer and unplug its power cord.2. When handling the motherboard, avoid touching any metal leads or connectors.3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.5. Please verify that the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.2. Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.3. Before using the product, please verify that all cables and power connectors are connected.4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.5. Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.6. Please do not place the computer system on an uneven surface.7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty1. Damage due to natural disaster, accident or human cause.2. Damage as a result of violating the conditions recommended in the user manual.3. Damage due to improper installation.4. Damage due to use of uncertified components.5. Damage due to use exceeding the permitted parameters.6. Product determined to be an unofficial Gigabyte product.

Chapter 1 Hardware Installation

GA-N680SLI-DQ6 Motherboard - 10 -

Engl

ish

1-2 Feature SummaryCPU LGA775 for Intel® CoreTM 2 Extreme quad-core / CoreTM 2 Extreme dual-core /

CoreTM 2 Quad / CoreTM 2 Duo / Pentium® processor Extreme Edition /Pentium® D / Pentium® 4 / Celeron® DL2 cache varies with CPU

Front Side Bus Supports 1333/1066/800/533 MHz FSBChipset nVIDIA® nForce 680i SLI

(Northbridge: C55XE, Southbridge: MCP55P)LAN Onboard Marvell 88E8052/88E8056 chip (10/100/1000 Mbit)

2 Onboard Marvell 88E1116 phy (10/100/1000 Mbit)Audio Onboard Realtek ALC888 DD chip

Supports High Definition AudioSupports 2 / 4 / 6 / 8 channel audioSupports DTS (dts NEO : PC) functionSupports Dolby Digital LiveSupports S/PDIF In/Out connectionSupports CD In connection

IEEE 1394 Onboard T.I. TSB43AB23 chip3 IEEE 1394a ports

Storage nVIDIA® nForce 680i SLI Southbridge- 1 FDD connector supported by I/O controller, allowing connection of

1 FDD device- 1 IDE connector with Ultra DMA-33, ATA-66/100/133 support,

allowing connection of 2 IDE devices- 6 SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATAII4,

SATAII5), allowing connection of 6 SATA 3Gb/s devices- Supports data RAID 0, RAID 1, RAID 0+1, RAID 5 and JBOD for

Serial ATAGIGABYTE SATA2 x 2 Controller- 4 SATA 3Gb/s connectors (GSATAII1-0, GSATAII1-1, GSATAII2-0,

GSATAII2-1), allowing connection of 4 SATA 3Gb/s devices- Supports data RAID 0, RAID 1 and JBOD for Serial ATA

O.S Support Microsoft Windows 2000/XPMemory 4 DDRII DIMM memory slots (supports up to 8 GB memory)

Supports dual channel DDRII 800/667/533 unbuffered DIMMs (Note 1)

Supports 1.8V DDRII DIMMsSupports ECC type DRAM

Expanstion Slots 2 PCI Express x16 slots1 PCI Express x8 slot1 PCI Express x1 slot3 PCI slots


EnglishInternal Connectors 1 24-pin ATX power connector1 8-pin ATX 12V power connector1 4-pin PCIe 12V power connector1 floppy connector1 IDE connector10 SATA 3Gb/s connectors1 CPU fan connector1 system fan connector1 power fan connector1 North Bridge fan connector1 front panel connector1 front audio connector1 CD In connector1 S/PDIF In connector3 USB 2.0/1.1 connectors for additional 6 ports by cables2 IEEE 1394a connectors for additional 2 ports by cables1 TPM connector1 LPT connector1 power LED connector1 Chassis Intrusion connector

Rear Panel I/O 1 PS/2 keyboard port1 PS/2 mouse port1 serial port1 IEEE 1394a port1 S/PDIF out port (optical)4 RJ-45 port4 USB 2.0/1.1 ports6 audio jacks (Line In / Line Out / MIC In / Surround Speaker Out (RearSpeaker Out) / Center/Subwoofer Speaker Out / Side Speaker Out)

I/O Control IT8718 chipHardware Monitor System voltage detection

CPU / System temperature detectionCPU / System / Power fan speed detectionCPU warning temperatureCPU / System / Power fan failure warningCPU / System smart fan control

BIOS 2 4 Mbit flash ROMUse of licensed AWARD BIOSSupports Dual BIOSPnP 1.0a, DMI 2.0, SM BIOS 2.3, ACPI 1.0b


Engl

ish

(Note 1) To use a DDR II 800/667 memory module on the motherboard, you must install a 1333/1066/800 MHz FSB processor.

(Note 2) EasyTune functions may vary depending on different motherboards.(Note 3) The adjustable range is dependent on CPUs.

Additional Features Supports @BIOSSupports Download CenterSupports Q-FlashSupports EasyTune(Note 2)

Supports Xpress InstallSupports Xpress Recovery2Supports Xpress BIOS Rescue

Bundle Software Norton Internet Security (OEM revision)Overclocking Over Voltage via BIOS (CPU, DDRII, NB/PCIE, SB/PCIE, FSB,

HT-Link, SB Standby)- CPU Voltage :

Adjustable CPU voltage at 0.025V (Note 3)

- DDRII Voltage :Adjustable DDRII voltage at 0.025V(Adjustable range from 0.025V to 0.775V)

- NB/PCIE Voltage :Adjustable PCIe voltage at 0.05V(Adjustable range from 0.05V to 0.20V)

- SB/PCIE Voltage :Adjustable PCIe voltage at 0.05V(Adjustable range from 0.05V to 0.55V)

- FSB Voltage :Adjustable FSB voltage at 0.05V(Adjustable range from 0.05V to 0.35V)

- HT-Link Voltage :Adjustable HT-Link voltage at 0.05V(Adjustable range from 0.05V to 0.35V)

- SB Standby Voltage :Adjustable SB Standby voltage at 0.10V(Adjustable range from 0.10V to 0.20V)

Over Clock via BIOS (CPU, DDRII, PCIE)- PCI Express x16 Clock:

Allows 1 MHz increment from 100 MHz to 150 MHz- PCI Express x8 Clock:

Allows 1 MHz increment from 100 MHz to 150 MHz- Adjustable CPU, DDRII frequencies

Form Factor ATX form factor; 30.5cm x 24.4cm


English

1-3 Installation of the CPU and CPU Cooler

1-3-1 Installation of the CPUFig. 1Gently lift the metallever located on theCPU socket to theupright position.

Metal LeverFig. 2Remove the plast iccovering on the CPUsocket.

Fig. 3Notice the small goldcolored triangle locatedon the edge of the CPUsocket. Align theindented corner of the

Fig. 4Once the CPU isproperly inserted,please replace theload plate and push themetal lever back intoits original position.

CPU with the triangle and gently insert the CPU intoposition. (Grasping the CPU firmly between yourthumb and forefinger, carefully place it into the socketin a straight and downwards motion. Avoid twisting orbending motions that might cause damage to the CPUduring installation.)

Before installing the CPU, please comply with the following conditions:1. Please make sure that the motherboard supports the CPU.2. Please take note of the one indented corner of the CPU. If you install the CPU in the

wrong direction, the CPU will not insert properly. If this occurs, please change theinsert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and CPU cooler.4. Please make sure the CPU cooler is installed on the CPU prior to system use,

otherwise overheating and permanent damage of the CPU may occur.5. Please set the CPU host frequency in accordance with the processor specifications. It

is not recommended that the system bus frequency be set beyond hardware specifica-tions since it does not meet the required standards for the peripherals. If you wish to setthe frequency beyond the proper specifications, please do so according to your hard-ware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :Enabling the functionality of Hyper-Threading Technology for your computer system requiresall of the following platform components:- CPU: An Intel® Pentium 4 Processor with HT Technology- Chipset: An Intel® Chipset that supports HT Technology- BIOS: A BIOS that supports HT Technology and has it enabled- OS: An operation system that has optimizations for HT Technology


Engl

ish

1-3-2 Installation of the CPU Cooler

The CPU cooler may adhere to the CPU as a result of hardening of the heat paste. To preventsuch an occurrence, it is suggested that either thermal tape rather than heat paste be used forheat dissipation or using extreme care when removing the CPU cooler.

Fig. 6Finally, please attach the power connector of theCPU cooler to the CPU fan header located on themotherboard.

Fig. 3Place the CPU cooler atop the CPU and makesure the push pins aim to the pin hole on themotherboard.Pressing down the push pinsdiagonally.

Fig. 4Please make sure the Male and Female push pinare jo ined closely. ( for detai led instal lat ioninstructions, please refer to the CPU cooler instal-lation section of the user manual)

Fig. 5Please check the back of motherboard afterinstalling. If the push pin is inserted as the picture,the installation is complete.

Fig.1Please apply an even layer of CPU cooler pasteon the surface of the installed CPU.

Fig. 2(Turning the push pin along the direction of arrow is toremove the CPU cooler, on the contrary, is to install.)Please note the direction of arrow sign on the malepush pin doesn't face inwards before installation. (Thisinstruction is only for Intel boxed fan)

Male Push Pin

Female Push Pin

The top of Female Push Pin


English

The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memorycapacity and specifications. Memory modules are designed so that they can be inserted only in one direction.The memory capacity used can differ with each slot.

Before installing the memory modules, please comply with the following conditions:1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.2. Before installing or removing memory modules, please make sure that the computer

power is switched off to prevent hardware damage.3. Memory modules have a foolproof insertion design. A memory module can be installed

in only one direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

Notch

Fig.1The DIMM socket has a notch, so the DIMM memorymodule can only fit in one direction. Insert the DIMM memorymodule vertically into the DIMM socket. Then push it down.

Fig.2Close the plastic clip at both edges of the DIMM sockets tolock the DIMM module.Reverse the installation steps when you wish to removethe DIMM module.

DDRII


Engl

ish

Dual Channel Memory ConfigurationThe GA-N680SLI-DQ6 supports the Dual Channel Technology. After operat-ing the Dual Channel Technology, the bandwidth of memory bus will double.

The GA-N680SLI-DQ6 includes 4 DIMM sockets, and each Channel has two DIMM sockets asfollowing:

Channel 0 : DDRII1, DDRII2Channel 1 : DDRII3, DDRII4

If you want to operate the Dual Channel Technology, please note the following explanations due to thelimitation of chipset specifications.

1. Dual Channel mode will not be enabled if only one DDRII memory module is installed.2. To enable Dual Channel mode with two or four memory modules (it is recommended to use

memory modules of identical brand, size, chips, and speed), you must install them into DIMMsockets of the same color.

The following is a Dual Channel Memory configuration table:(DS: Double Side, SS: Single Side, "--": Empty)

2 memory modules

4 memory modules

DDRII1 DDRII2 DDRII3 DDRII4DS/SS - - DS/SS - -- - DS/SS - - DS/SSDS/SS DS/SS DS/SS DS/SS

If two memory modules are to be used to achieve Dual Channel mode, we recommendinstalling them in DDRII1 and DDRII3 DIMM sockets.


English

1-5 Installation of Expansion CardsTo install your expansion card, follow the steps below.1. Disconnect your system from its power source and read the expansion card's installation manual

before installing the expansion card in the computer.2. Remove your computer's chassis cover, screws and slot bracket from the computer. Ground

yourself to prevent damage to your computer resulting from Electrostatic discharge (ESD).3. Press the expansion card firmly into the expansion slot in the motherboard.4. Make sure the metal contacts on the card are fully seated in the slot.5. Replace the screw to secure the slot bracket of the expansion card.6. Replace your computer's chassis cover.7. Power on the computer, if necessary, configure required settings for the expansion card in system

BIOS Setup.8. Install related driver in the operating system.

For example: Installing a PCI Express x16 VGA card:

The motherboard includes a PCIE_12V power connector, which providesextra power to the onboard PCI Express x16 slot. When installing twographics cards, please connect the power cable from the power supply tothis connector.

To remove the VGA card:When you try to uninstall the VGA card on the PCI Express x16 slot, youcan press the latch as the picture to the left shows to release the card.

To install the VGA card:Please align the VGA card with the PCI Ex-press x16 slot and press down on the card.Make sure the VGA card is locked by thesmall white drawable bar.


Engl

ish

1-6 Connecting the e-SATA Cable Kit

The e-SATA cable kit includes one SATA bracket,one SATA signal cable, and one SATA power cable.

Step 1:Locate one free PCIslot and secure theSATA bracket to thechassis back panelwith a screw.

Follow the steps below to install the e-SATA cable kit:

Step 2:Connect the SATAc a b l e f r o m t h ebracket to the SATAport on yourmotherboard.

Step 3:Connect the powerc a b l e f r o m t h ebracket to the powersupply.

Step 4:Plug one end of theSATA signal cable intothe e-SATA connec-tor on the bracket.Then attach the SATApower cable to thepower connector onthe bracket.

The e-SATA cable kit allows you to connect external SATA device(s) to your system by expanding theinternal SATA port(s) to the chassis back panel.

• Turn off your system and the power switch on the power supply before installing orremoving the SATA bracket and SATA power cable to prevent damage to hardware.

• Insert the SATA signal cable and SATA power cable securely into the corresponding connec-tors when installing.

Step 5:Connect the other ends of the SATA signal cable and SATA power cableto your SATA devices. For SATA device in external enclosure, you onlyneed to connect the SATA signal cable. Before connecting the SATA signalcable, make sure to turn off the power of the external enclosure.

SATA Bracket

e-SATAConnector Power

Connectore-SATA

Connector

SATA Signal Cable SATA Power Cable


English

1-7 Setup of SLI (Scalable Link Interface) ConfigurationnVIDIA® nForce 680i SLI offers blistering graphics performance with the ability to bridge two NVIDIA SLI-ready PCI ExpressTM graphics cards! The SLI design takes advantage of the increased bandwidth ofthe PCI ExpressTM bus architecture, features hardware and software innovations within NVIDIA GPU(graphics processing unit) and the nVIDIA® nForce 680i SLI chipset. Together, the NVIDIA SLI technolo-gies work seamlessly to allow two graphics cards to operate in parallel and share the work and deliverheart-pounding PC performance. This section introduces steps to configure an SLI system on theGA-N680SLI-DQ6 motherboard.

The exact power requirements will depend on your overall system configurations. You needa power supply that can provide sufficient and stable power to your system and the two SLIgraphics cards. Please refer to the table below to check recommended power for differentsystems.

Before you begin--

If you wish to enable the SLI function, install two SLI-ready graphics cards into the PCIE_16_1 andPCIE_16_2 slots. (It is recommended to use graphics cards of identical brand and chips. For example:GIGABYTE GV-NX76T256D-RH).If you want to set up a single graphics card system, we recommend installing the graphics card on thePCIE_16_1 slot to ensure better display performance.

System configuration System A System BProcessors Intel QX6700 Intel X6800PCIE x16 video cards 2±iNVIDIA 6800 Ultra cards 2±iNVIDIA 6600 GT cardsDDR memory modules 4 DIMMs 2 DIMMsHard drives/Optical drives 4 hard drives + 2 optical drives 1 hard drives + 1 optical drivesExpansion cards 1 PCIE x1 card + 2 PCI cards 0USB devices 10 4IEEE 1394 devices 1 0Required +12V current 25A or above 20A or abovePower supply requirement 500W or above 350W or above


Engl

ish

place this part on the top ofthe bridge connector.

retention bracket

Connecting Two Graphics Cards:

Step 1: Observe the steps in "1-5 Installation of Expansion Cards"and install two SLI-ready graphics cards of the samemodel to the PCIE_16_1 and PCIE_16_2 slots.

Step 3: In order to securely fix the bridge connector beween thetwo cards, you must install the retention bracket in-cluded with the motherboard and secure the retentionbracket to the chassis back panel with a screw.

Gold edge connector on the topof graphics card

Female slots on the bridgeconnector

Step 2: Insert the SLI bridge (the GC-SLICON6) to the SLI goldedge connector on top of both cards. Make sure the twomini female slots on the bridge connector securely fitonto the SLI gold edge connetors of both cards.

Step 4: Plug the display cable into the graphics card which onthe PCIE_16_1 slot(Note).

(Note) If you want to enable the SLI function, you must plug the display cable into the graphics cardwhich on the PCIE_16_1 slot.


English

Graphics Card Driver Setting:

Step 1: After installing graphics card driver in operating system,right-click the NVIDIA icon in your system tray and thenselect NVIDIA Display. The NVIDIA control panel willappear.

Step 2: Select SLI multi-GPU from the side menu and thenselect the Enable SLI multi-GPU checkbox in the SLImulti-GPU dialog box. System will restart after youclick Apply. Then the SLI configuration is completed.


Engl

ish

1-8 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse ConnectorTo install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and thekeyboard to the lower port (purple).COMAConnects to serial-based mouse or data processing devices.OPTICALThe S/PDIF optical output port is capable of providing digital audio to external speakers orcompressed AC3 data to an external Dolby Digital Decoder via an optical cable.IEEE 1394 Port (4 Pins Connector)Serial interface standard set by Institute of Electrical and Electronics Engineers, which has featureslike high speed, high bandwidth and hot plug.LAN PortThe provided Internet connection is Gigabit Ethernet , providing data transfer speeds of 10/100/1000 Mbps.USB PortBefore you connect your device(s) into USB connector(s), please make sure your device(s) suchas USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Alsomake sure your OS supports USB controller. If your OS does not support USB controller, pleasecontact OS vendor for possible patch or driver upgrade. For more information please contact yourOS or device(s) vendors.Center/Subwoofer Speaker OutThe default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected toCenter/Subwoofer Speaker Out jack.Surround Speaker Out (Rear Speaker Out)The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can beconnected to Surround Speaker Out (Rear Speaker Out) jack.Side Speaker OutThe default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Outjack.Line InThe default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.Line Out (Front Speaker Out)The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surroundspeakers can be connected to Line Out (Front Speaker Out) jack.


English

1-9 Connectors Introduction

2

1 4 22

8

10

915

19

16

5

12

MIC InThe default MIC In jack. Microphone must be connected to MIC In jack.

In addition to the default speakers settings, the ~ audio jacks can be reconfigured toperform different functions via the audio software. Only microphones still MUST be connectedto the default Mic In jack ( ). Please refer to the 2-/4-/6-/8- channel audio setup steps fordetailed software configuration information.

6

3

11 14

2317

13

18

2021

1) ATX_12V_2X2) ATX (Power Connector)3) PCIE_12V4) CPU_FAN5) SYS_FAN6) PWR_FAN7) NB_FAN8) FDD9) IDE

10) SATAII0 / 1 / 2 / 3 / 4 / 511) GSATAII1-0 / GSATAII1-1 / GSATAII2-0 /

GSATAII2-1

12) PWR_LED13) BATTERY14) F_PANEL15) F_AUDIO16) CD_IN17) SPDIF_IN18) F_USB1 / F_USB2 / F_USB319) F1_1394 / F2_139420) LPT21) TPM22) C I23) CLR_CMOS

7


Engl

ish

1/2) ATX_12V_2X / ATX (Power Connector)With the use of the power connector, the power supply can supply enough stable power to all thecomponents on the motherboard. Before connecting the power connector, please make sure thatall components and devices are properly installed. Align the power connector with its properlocation on the motherboard and connect tightly.The ATX 12V (2x4-pin) power connector mainly supplies power to the CPU. If the ATX 12V (2x4)power connector is not connected, the system will not start. If you wish to install a power supplythat provides ATX 12V (2x2-pin) power connector, please connect the ATX 12V power connectorto the Pin 3, 4, 7, 8 of the onboard ATX_12V_2X power connector according to the pin definitions.Important Use of a power supply providing an ATX 12V (2x4-pin) power connector is recom-mended by processor manufacturer when using Intel® Pentium® Extreme Edition series processors(130W or greater).Caution! Please use a power supply that is able to handle the system voltage requirements. It isrecommended that a power supply that can withstand high power consumption be used (400W orgreater). If a power supply is used that does not provide the required power, the result can lead to anunstable system or a system that is unable to start. If you use a power supply that provides a 24-pinATX or 2x4 pin ATX 12V power connector, please remove the small cover on the power connector onthe motherboard before plugging in the power cord; otherwise, please do not remove it.

Pin No. Definition1 GND2 GND3 GND4 GND5 +12V6 +12V7 +12V8 +12V

1

4

5

8

131

2412 Pin No. Definition13 3.3V14 -12V15 GND16 PS_ON(soft On/Off)17 GND18 GND19 GND20 -5V21 +5V22 +5V23 +5V (Only for 24-pin ATX)24 GND(Only for 24-pin ATX)

Pin No. Definition1 3.3V2 3.3V3 GND4 +5V5 GND6 +5V7 GND8 Power Good9 5V SB(stand by +5V)10 +12V11 +12V(Only for 24-pin ATX)12 3.3V(Only for 24-pin ATX)

ATX_12V_2X

ATX


English

4/5/6) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN/SYS_FAN) power connector and possesses a foolproof connection design.Most coolers are designed with color-coded power connector wires. A red power connector wireindicates a positive connection and requires a +12V power voltage. The black connector wire isthe ground wire (GND).Remember to connect the CPU/system/power fan cable to the CPU_FAN/SYS_FAN/PWR_FANconnector to prevent CPU damage or system hanging caused by overheating.

1

Pin No. Definition1 GND2 +12V / Speed Control3 Sense4 Speed Control

3) PCIE_12V (Power Connector)This power connector provides extra power to the onboard PCI Express x16 slot. When installingtwo graphics cards, please connect the power cable from the power supply to this connector, orsystem instability may occur.

PIin No. Definition1 NC2 GND3 GND4 +12V

PWR_FAN

1

CPU_FAN / SYS_FAN :

Pin No. Definition1 GND2 +12V3 Sense

PWR_FAN :

CPU_FAN / SYS_FAN

1


Engl

ish

7) NB_FAN (North Bridge Fan Header)Connect the North Bridge fan cable to this header. The fan header has a foolproof insertion design.When connecting a fan cable, be sure to connect it in the correct orientation. Most fans are designedwith color-coded power connector wires. A red power connector wire indicates a positive connec-tion and requires a +12V voltage. The black connector wire is the ground wire.

1 Pin No. Definition1 GND2 +12V3 NC

8) FDD (Floppy Connector)The FDD connector is used to connect the FDD cable while the other end of the cable connects tothe FDD drive. The types of FDD drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB and2.88 MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDDconnector.

12

3334


English

9) IDE (IDE Connector)An IDE device connects to the computer via an IDE connector. One IDE connector can connect to oneIDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive).If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and theother as Slave (for information on settings, please refer to the instructions located on the IDE device).Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

2

40

1

39

10) SATAII0 / 1 / 2 / 3 / 4 / 5 (SATA 3Gb/s Connector, Controlled by nVIDIA® nForce 680i SLISouthbridge)SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA3Gb/s and install the proper driver in order to work properly.

Pin No. Definition1 GND2 TXP3 TXN4 GND5 RXN6 RXP7 GND

7

17

1

SATAII5

SATAII4

7

1 7

1

SATAII0

SATAII1

7

17

1

SATAII3

SATAII2


Engl

ish

11) GSATAII1-0 / GSATAII1-1 / GSATAII2-0 / GSATAII2-1 (SATA 3Gb/s Connector, Controlledby GIGABYTE SATA2)SATA 3Gb/s can provide up to 300 MB/s transfer rate. Please refer to the BIOS setting for the SATA3Gb/s and install the proper driver in order to work properly.

Pin No. Definition1 GND2 TXP3 TXN4 GND5 RXN6 RXP7 GND

1 7

12) PWR_LEDThe PWR_LED connector is connected with the system power indicator to indicate whether thesystem is on/off. It will blink when the system enters suspend mode(S1).

Pin No. Definition1 MPD+2 MPD-3 MPD-

1


English

13) BATTERY

Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommended by themanufacturer.

Dispose of used batteries according to the manufacturer's instructions.If you want to erase CMOS...1. Turn off the computer and unplug the power cord.2. Gently take out the battery and put it aside for about one minute.

(Or you can use a metal object to connect the positive and negativepins in the battery holder to make them short for five seconds.)

3. Re-install the battery.4. Plug the power cord in and turn on the computer.

14) F_PANEL (Front Panel Jumper)Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassisfront panel to the F_PANEL connector according to the pin assignment below.

12

1920

HD-

HD+ RE

S+RE

S- NC

IDE Hard Disk Active LED

Reset Switch

SPEA

K-

MSG-

MSG+

PW-

PW+

Message LED/Power/

Sleep LED

Speaker Connector

SPEA

K+PowerSwitch

MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)(Yellow) Pin 2: LED cathode(-)PW (Power Switch) Open: Normal(Red) Close: Power On/OffSPEAK (Speaker Connector) Pin 1: Power(Amber) Pin 2- Pin 3: NC

Pin 4: Data(-)HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)(Blue) Pin 2: LED cathode(-)RES (Reset Switch) Open: Normal(Green) Close: Reset Hardware SystemNC ( Purple) NC


Engl

ish

16) CD_IN (CD IN Connector)Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No. Definition1 CD-L2 GND3 GND4 CD-R

15) F_AUDIO (Front Audio Connector)This connector supports either HD (High Definition) or AC97 front panel audio module. If you wishto use the front audio function, connect the front panel audio module to this connector. Check the pinassignments carefully while you connect the front panel audio module. Incorrect connectionbetween the module and connector will make the audio device unable to work or even damage it.For optional front panel audio module, please contact your chassis manufacturer.

By default, the audio driver is configured to support HD Audio. To connect an AC97 front panelaudio module to this connector, please refer to the instructions on page 101 about the softwaresettings.

Pin No. Definition1 MIC2 GND3 MIC Power4 NC5 Line Out (R)6 NC7 NC8 No Pin9 Line Out (L)10 NC

AC'97 Audio:Pin No. Definition

1 MIC2_L2 GND3 MIC2_R4 -ACZ_DET5 LINE2_R6 FSENSE17 FAUDIO_JD8 No Pin9 LINE2_L10 FSENSE2

HD Audio:12

910

1


English

17) SPDIF_IN (S/PDIF In Connector)Use S/PDIF IN feature only when your device has digital output function. Be careful with thepolarity of the SPDIF_IN connector. Check the pin assignment carefully while you connect theS/PDIF cable, incorrect connection between the cable and connector will make the device unableto work or even damage it. For optional S/PDIF cable, please contact your local dealer.

Pin No. Definition1 Power2 SPDIFI3 GND

1

18) F_ USB1 / F_USB2 / F_USB3 (Front USB Connector)Be careful with the polarity of the front USB connector. Check the pin assignment carefully whileyou connect the front USB cable, incorrect connection between the cable and connector will makethe device unable to work or even damage it. For optional front USB cable, please contact yourlocal dealer.

1 2

9 10

Pin No. Definition1 Power (5V)2 Power (5V)3 USB DX-4 USB DY-5 USB DX+6 USB DY+7 GND8 GND9 No Pin10 NC


Engl

ish

19) F1_1394 / F2_1394 (Front IEEE 1394 Connector)Serial interface standard set by Institute of Electrical and Electronics Engineers, which has featureslike high speed, high bandwidth and hot plug. Be careful with the polarity of the IEEE 1394connector. Check the pin assignment carefully while you connect the IEEE 1394 cable, incorrectconnection between the cable and connector will make the device unable to work or even damageit. For optional IEEE 1394 cable, please contact your local dealer.

Pin No. Definition1 TPA+2 TPA-3 GND4 GND5 TPB+6 TPB-7 Power (12V)8 Power (12V)9 No Pin10 GND

1

9

2

10

20) LPT ConnectorThe LPT connector allows connection of a printer, scanner and other peripheral devices.

1

2

25

26

Pin No. Definition1 STB-2 AFD-3 PD04 ERR-5 PD16 INIT-7 PD28 SLIN-9 PD310 GND11 PD412 GND13 PD5

Pin No. Definition14 GND15 PD616 GND17 PD718 GND19 ACK-20 GND21 BUSY22 GND23 PE24 No Pin25 SLCT26 GND


English

22) CI (Chassis Intrusion, Case Open)This 2-pin connector allows your system to detect if the chassis cover is removed. You can checkthe "Case Opened" status in BIOS Setup.

1Pin No. Definition

1 Signal2 GND

21) TPM Connector (Trusted Platform Module)Please contact your nearest dealer for optional TPM cable.

Pin No. Definition1 LCLK2 GND3 LFRAME4 No Pin5 LRESET6 VCC57 LAD38 LAD29 VCC310 LAD1

Pin No. Definition11 LAD012 GND13 RSVO14 RSV115 SB3V16 SERIRQ17 GND18 CLKRUN19 LPCPD20 RSV2

1

2

19

20


Engl

ish

Open: Normal

Short: Clear CMOS

23) CLR_CMOS (Clear CMOS)You may clear the CMOS data to its default values by this header. To clear CMOS, temporarilyshort the two pins. Default doesn't include the jumper to avoid improper use of this header.

BIOS Setup- 35 -

EnglishBIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configurerequired settings or to activate certain system features.The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.When the power is turned off, the battery on the motherboard supplies the necessary power to theCMOS SRAM.When the power is turned on, pressing the <Del> button during the BIOS POST (Power-On Self Test) willtake you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".If you wish to upgrade to a new BIOS, either Gigabyte's Q-Flash or @BIOS utility can be used.Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operatingsystem.@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS butdirectly download and update BIOS from the Internet.

Main MenuThe on-line description of the highlighted setup function is displayed at the bottom of the screen.Status Page Setup Menu / Option Page Setup MenuPress F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-tions for the highlighted item. To exit the Help Window press <Esc>.

Chapter 2 BIOS Setup

CONTROL KEYS< > < > < > < > Move to select item<Enter> Select Item<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main Menu<Page Up> Increase the numeric value or make changes<Page Down> Decrease the numeric value or make changes<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu<F2> Item Help<F5> Restore the previous CMOS value from CMOS, only for Option Page Setup

Menu<F6> Load the fail-safe default CMOS value from BIOS default table<F7> Load the Optimized Defaults<F8> Dual BIOS/Q-Flash utility<F9> System Information<F10> Save all the CMOS changes, only for Main Menu<F11> Save CMOS to BIOS - CMOS Profiles<F12> Load CMOS from BIOS - CMOS Profiles

Because BIOS flashing is potentially risky, please do it with caution and avoid inadequateoperation that may result in system malfunction.


Engl

ish

<TAB> : POST ScreenPress the TAB key to see BIOS POST screen.(To show the BIOS POST screen at system startup, refer to the instructions on the Full Screen LOGO Show item on page 42.)

<DEL> : BIOS Setup/Dual BIOSPress the DELETE key to enter BIOS Setup program.<F9> : Xpress Recovery2Press the F9 key to enter the Xpress Recovery2 screen.<F12> : Boot MenuPress the F12 key to enter Boot Menu to select the first boot device.<End> : QflashPress the End key to enter Q-Flash utility.

Startup Screen:

<TAB>:POST Screen <DEL>:BIOS Setup/Dual BIOS <F9>:XpressRecovery2 <F12>:Boot Menu <End>: Qflash

BIOS Setup- 37 -

English

Standard CMOS FeaturesThis setup page includes all the items in standard compatible BIOS.Advanced BIOS FeaturesThis setup page includes all the items of Award special enhanced features.Integrated PeripheralsThis setup page includes all onboard peripherals.Power Management SetupThis setup page includes all the items of Green function features.PnP/PCI ConfigurationThis setup page includes all the configurations of PCI & PnP ISA resources.PC Health StatusThis setup page is the System auto detect Temperature, voltage, fan, speed.

BIOS Setting Recovery F11 : Save CMOS to BIOS

This function allows you to make a record of the current CMOS settings as a profile.You can create up to 8 profiles (Profile 1-8) and give each of them a name.

F12 : Load CMOS from BIOSIf your system becomes unstable and you load the default BIOS settings, you can use this functionto reload the CMOS settings with a CMOS settings profile created before, without the hassles ofresetting the CMOS configurations.

The Main Menu (For example: BIOS Ver. : FAa)Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on thescreen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

CMOS Setup Utility-Copyright (C) 1984-2007 Award Software

Standard CMOS FeaturesAdvanced BIOS FeaturesIntegrated PeripheralsPower Management SetupPnP/PCI ConfigurationsPC Health StatusMB Intelligent Tweaker(M.I.T.)

Load Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit : Select Item F11: Save CMOS to BIOSF8: Dual BIOS/Q-Flash F10: Save & Exit Setup F12: Load CMOS from BIOS

Time, Date, Hard Disk Type...

1. If you don’t find the settings you want, press "Ctrl+F1" to access advanced options.2. Select the Load Optimized Defaults item in the BIOS Setup when somehow the system

is not stable as usual. This action makes the system reset to the default settings for stability.3. The BIOS Setup menus described in this chapter are for reference only and may differ from

the exact settings for your motherboard.


Engl

ish

MB Intelligent Tweaker(M.I.T.)This setup page is control CPU clock and frequency ratio.Load Fail-Safe DefaultsFail-Safe Defaults indicates the value of the system parameters which the system would be in safeconfiguration.Load Optimized DefaultsOptimized Defaults indicates the value of the system parameters which the system would be inbest performance configuration.Set Supervisor PasswordChange, set, or disable password. It allows you to limit access to the system and Setup, or justto Setup.Set User PasswordChange, set, or disable password. It allows you to limit access to the system.Save & Exit SetupSave CMOS value settings to CMOS and exit setup.Exit Without SavingAbandon all CMOS value changes and exit setup.

BIOS Setup- 39 -

English

2-1 Standard CMOS Features

DateThe date format is <week>, <month>, <day>, <year>.

Week The week, from Sun to Sat, determined by the BIOS and is display-onlyMonth The month, Jan. Through Dec.Day The day, from 1 to 31 (or the maximum allowed in the month)Year The year, from 2000 through 2099

TimeThe times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. For example, 1 p.m. is 13:0:0.IDE Channel 0 Master, Slave

IDE HDD Auto-DetectionPress "Enter" to select this option for automatic device detection.

IDE Device Setup. You can use one of three methods:• Auto Allows BIOS to automatically detect IDE/SATA devices during POST(default)• None Select this if no IDE/SATA devices are used and the system will skip the

automatic detection step and allow for faster system start up.• Manual User can manually input the correct settings.

Access Mode Use this to set the access mode for the hard drive. The four options are:CHS/LBA/Large/Auto(default:Auto)

IDE Channel 2/3/4/5/6/7 MasterIDE HDD Auto-Detection

Press "Enter" to select this option for automatic device detection.Extended IDE Drive. You can use one of two methods:

• Auto Allows BIOS to automatically detect IDE/SATA devices during POST(default)• None Select this if no IDE/SATA devices are used and the system will skip the

automatic detection step and allow for faster system start up.

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwareStandard CMOS Features

Date (mm:dd:yy) Fri, Apr 20 2007Time (hh:mm:ss) 22:31:24

IDE Channel 0 Master [None]IDE Channel 0 Slave [None]IDE Channel 2 Master [None]IDE Channel 3 Master [None]IDE Channel 4 Master [None]IDE Channel 5 Master [None]IDE Channel 6 Master [None]IDE Channel 7 Master [None]

Drive A [1.44M, 3.5"]Floppy 3 Mode Support [Disabled]

Halt On [All, But Keyboard]

Base Memory 1664KExtended Memory 511M

: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item HelpMenu Level


Engl

ish

Access Mode Use this to set the access mode for the hard drive. The two options are:Large/Auto(default:Auto)

Capacity Capacity of currectly installed hard drive.Cylinder Number of cylindersHead Number of headsPrecomp Write precompLanding Zone Landing zoneSector Number of sectors

Drive AThe category identifies the types of floppy disk drive A that has been installed in the computer.

None No floppy drive installed.360K, 5.25" 5.25 inch PC-type standard drive; 360 K byte capacity.1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2 M byte capacity.

(3.5 inch when 3 Mode is Enabled).720K, 3.5" 3.5 inch double-sided drive; 720 K byte capacity.1.44M, 3.5" 3.5 inch double-sided drive; 1.44 M byte capacity.2.88M, 3.5" 3.5 inch double-sided drive; 2.88 M byte capacity.

Floppy 3 Mode Support (for Japan Area)Disabled Normal Floppy Drive. (Default value)Drive A Drive A is 3 mode Floppy Drive.

Halt onThe category determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error that may be detected and youwill be prompted.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other

errors. (Default value)All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all

other errors.MemoryThe category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base MemoryThe POST of the BIOS will determine the amount of base (or conventional) memory installed in thesystem.The value of the base memory is typically 512 K for systems with 512 K memory installed on themotherboard, or 640 K for systems with 640 K or more memory installed on the motherboard.

Extended MemoryThe BIOS determines how much extended memory is present during the POST.This is the amount of memory located above 1 MB in the CPU's memory address map.

BIOS Setup- 41 -

English

2-2 Advanced BIOS Features

Hard Disk Boot PrioritySelect boot sequence for onboard(or add-on cards) SCSI, RAID, etc.Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list.Press <ESC> to exit this menu.First / Second / Third Boot Device

Floppy Select your boot device priority by Floppy.LS120 Select your boot device priority by LS120.Hard Disk Select your boot device priority by Hard Disk.CDROM Select your boot device priority by CDROM.ZIP Select your boot device priority by ZIP.USB-FDD Select your boot device priority by USB-FDD.USB-ZIP Select your boot device priority by USB-ZIP.USB-CDROM Select your boot device priority by USB-CDROM.USB-HDD Select your boot device priority by USB-HDD.Legacy LAN Select your boot device priority by Legacy LAN.Disabled Disable this function.

Password CheckSetup The system will boot but will not access to Setup page if the correct

password is not entered at the prompt. (Default value)System The system will not boot and will not access to Setup page if the correct

password is not entered at the prompt.

(Note) This item will show up when you install a processor that supports this function.

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwareAdvanced BIOS Features

Hard Disk Boot Priority [Press Enter]First Boot Device [Floppy]Second Boot Device [Hard Disk]Third Boot Device [CDROM]Password Check [Setup]HDD S.M.A.R.T. Capability [Disabled]CPU Hyper-Threading (Note) [Enabled]Limit CPUID Max. to 3 (Note) [Disabled]No-Execute Memory Protect (Note) [Enabled]CPU Enhanced Halt (C1E) (Note) [Enabled]CPU Thermal Monitor 2(TM2) (Note) [Enabled]CPU EIST Function (Note) [Enabled]Virtualization Technology (Note) [Enabled]Full Screen LOGO Show [Enabled]Init Display First [PEG]


Item HelpMenu Level


Engl

ish

HDD S.M.A.R.T. CapabilityThis feature allows your hard disk to report read/write errors and to issue warnings when third-party hardware monitor utility is installed.

Enabled Enable HDD S.M.A.R.T. capability.Disabled Disable HDD S.M.A.R.T. capability. (Default value)

CPU Hyper-Threading (Note)

Enabled Enable CPU Hyper Threading Feature. Please note that this feature is onlyworking for operating system with multi processors mode supported.(Default value)

Disabled Disable CPU Hyper Threading.Limit CPUID Max. to 3 (Note)

Enabled Limit CPUID Maximum value to 3 when use older OS like NT4.Disabled Disable CPUID Limit for windows XP. (Default value)

No-Execute Memory Protect (Note)

Enabled Enable No-Execute Memory Protect function. (Default value)Disabled Disable No-Execute Memory Protect function.

CPU Enhanced Halt (C1E) (Note)

Enabled Enable CPU Enhanced Halt (C1E) function. (Default value)Disabled Disable CPU Enhanced Halt (C1E) function.

CPU Thermal Monitor 2 (TM2) (Note)

Enabled Enable CPU Thermal Monitor 2 (TM2) function. (Default value)Disabled Disable CPU Thermal Monitor 2 (TM2) function.

CPU EIST Function (Note)

Enabled Enable CPU EIST function. (Default value)Disabled Disable CPU EIST function.

Virtualization Technology (Note)

Enabled Enable Virtualization Technology function. (Default value)Disabled Disable Virtualization Technology function.

Full Screen LOGO ShowEnabled Show full screen logo at system startup. (Default value)Disabled Disable this function. If you wish to see BIOS POST screen, set this item to

"Disabled".Init Display FirstThis feature allows you to select the first initiation of the monitor display from which card when youinstall a PCI card and a PCI Express VGA card on the motherboard.

PCI Set Init Display First to PCI VGA card.PEG Set Init Display First to PCI Express VGA card (the PCIE_16_1 slot).

(Default value)PEG(Slot2) Set Init Display First to PCI Express VGA card (the PCIE_8 slot).PEG(Slot3) Set Init Display First to PCI Express VGA card (the PCIE_16_2 slot).


BIOS Setup- 43 -

English

2-3 Integrated PeripheralsCMOS Setup Utility-Copyright (C) 1984-2007 Award Software

Integrated PeripheralsOn-Chip IDE Channel0 [Enabled]IDE Prefetch Mode [Enabled]NV Serial-ATA Controller [All Enabled]Serial-ATA RAID Config [Press Enter]Onboard SATA-II Ctrl1 [Enabled]Onboard SATA-II Ctrl1 Mode [IDE]Onboard SATA-II Ctrl2 [Enabled]Onboard SATA-II Ctrl2 Mode [IDE]On-Chip MAC Lan [Auto]On-Chip MAC1 Lan [Auto]On-Chip SMART LAN [Press Enter]Onboard LAN1 Controller [Enabled]Onboard LAN2 Controller [Enabled]Onboard LAN Boot ROM [Disabled]Onboard Audio Function [Auto]On-Chip USB [V1.1+V2.0]USB Keyboard Support [Disabled]USB Mouse Support [Disabled]Onboard 1394 [Enabled]


Item HelpMenu Level

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwareIntegrated Peripherals


Item HelpMenu Level

Legacy USB storage detect [Enabled]Onboard Serial Port 1 [3F8/IRQ4]Onboard Parallel Port [378/IRQ7]Parallel Port Mode [SPP]

x ECP Mode Use DMA 3


Engl

ish

Serial-ATA RAID ConfigCMOS Setup Utility-Copyright (C) 1984-2007 Award Software

Serial-ATA RAID ConfigItem HelpMenu Level

NV SATA RAID function [Disabled]x NV SATA 1 Primary RAID Enabledx NV SATA 1 Secondary RAID Enabledx NV SATA 2 Primary RAID Enabledx NV SATA 2 Secondary RAID Enabledx NV SATA 3 Primary RAID Enabledx NV SATA 3 Secondary RAID Enabled


NV SATA RAID functionEnabled Enable NV SATA RAID function.Disabled Disable NV SATA RAID function. (Default value)

NV SATA 1 Primary RAIDEnabled Enable NV SATA 1 primary RAID function.Disabled Disable this function. (Default value)

NV SATA 1 Secondary RAIDEnabled Enable NV SATA 1 secondary RAID function.Disabled Disable this function. (Default value)



On-Chip IDE Channel0Enabled Enable onboard 1st channel IDE port. (Default value)Disabled Disable onboard 1st channel IDE port.

IDE Prefetch ModeEnabled Enable IDE data buffer to enhance HDD transfer speed. (Default value)Disabled Disable IDE data buffer for the system stability.

NV Serial-ATA ControllerAll Enabled Enable NV Serial-ATA Controller function. (Default value)SATA-1 Enable NV SATA-1 function.SATA-1+2 Enable NV SATA-1+2 functionDisabled Disable this function.

BIOS Setup- 45 -

English



Onboard SATA-II Ctrl1 (GSATAII1-0 / GSATAII1-1 connectors)Enabled Enable onboard SATA-II ctrl1 function. (Default value)Disabled Disable onboard SATA-II ctrl1 function.

Onboard SATA-II Ctrl1 ModeThis function allows users to decide the operating mode of the SATA-II Ctrl1 (GSATAII1-0 /GSATAII1-1) ports controlled by the Gigabyte SATA2 controller.

IDE Set the SATA-II Ctrl1 channel to IDE mode. (Default value)AHCI Set the SATA-II Ctrl1 channel to AHCI mode. Advanced Host Controller Inteface

(AHCI) is an interface specification that allows the storage driver to enableadvanced Serial ATA features such as Native Command Queuing and hot plug.For more details about AHCI, please visit Intel's website.

RAID Set the SATA-II Ctrl1 channel to RAID mode.Onboard SATA-II Ctrl2 (GSATAII2-0 / GSATAII2-1 connectors)

Enabled Enable onboard SATA-II ctrl2 function. (Default value)Disabled Disable onboard SATA-II ctrl2 function.

Onboard SATA-II Ctrl2 ModeThis function allows users to decide the operating mode of the SATA-II Ctrl2 (GSATAII2-0 /GSATAII2-1)ports controlled by the te Gigabyte SATA2 controller.

IDE Set the SATA-II Ctrl2 channel to IDE mode. (Default value)AHCI Set the SATA-II Ctrl2 channel to AHCI mode. Advanced Host Controller Inteface

(AHCI) is an interface specification that allows the storage driver to enableadvanced Serial ATA features such as Native Command Queuing and hot plug.For more details about AHCI, please visit Intel's website.

RAID Set the SATA-II Ctrl2 channel to RAID mode.On-Chip MAC Lan (LAN1)

Auto Auto-detect onboard LAN chip function. (Default value)Disabled Disable onboard LAN chip function.

On-Chip MAC1 Lan (LAN2)Auto Auto-detect onboard LAN1 chip function. (Default value)Disabled Disable onboard LAN1 chip function.


Engl

ish

On-Chip SMART LAN (LAN Cable Diagnostic Function) (For LAN1/LAN2)

This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LANcable. This feature will detect cabling issue and report the approximate distance to the fault or short.Refer to the following information for diagnosing your LAN cable:

When LAN Cable Is Functioning Normally...1. If no cable problem is detected on the LAN cable connected to a Gigabit hub, the Status fields

of Pair 1-2, Pair 3-6, Pair 4-5, and Pair 7-8 will show Normal and the Length fields will showN/A, as shown in the figure above.

2. If no cable problem is detected on the LAN cable connected to a 10/100 Mbps hub, the Statusfields of Pair 1-2 and Pair 3-6 will show Normal and the Length fields will show N/A.However, because Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, theirStatus fields will show Short or Open, and the length shown is the approximate length of theattached LAN cable.

When a Cable Problem Occurs...If a cable problem occurs on a specified pair of wires, the Status field will show Short or Openand the length shown will be the approximate distance to the fault or short.For example, if it shows Pair1-2 Status = Short / Length = 1.6m,it means that a fault or short might occur at about 1.6m on Pair 1-2.

When No LAN Cable Is Attached...If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will showOpen.

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwareSMART LAN

Item HelpMenu Level

Start detecting at Port 0.Pair1-2 Status = Normal / Length = N/APair3-6 Status = Normal / Length = N/APair4-5 Status = Normal / Length = N/APair7-8 Status = Normal / Length = N/A

Start detecting at Port 1.Pair1-2 Status = Normal / Length = N/APair3-6 Status = Normal / Length = N/APair4-5 Status = Normal / Length = N/APair7-8 Status = Normal / Length = N/A


BIOS Setup- 47 -

English

Onboard LAN1 Controller (The upper LAN connector of the back panel Dual LANconnectors)

Enabled Enable onboard LAN1 controller function. (Default value)Disabled Disable onboard LAN1 controller function.

Onboard LAN2 Controller (The lower LAN connector of the back panel Dual LANconnectors)

Enabled Enable onboard LAN2 controller function. (Default value)Disabled Disable onboard LAN2 controller function.

Onboard LAN Boot ROMThis function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled Enable this function.Disabled Disable this function. (Default value)

Onboard Audio FunctionAuto Auto-detect onboard audio function. (Default value)Disabled Disable this function.

On-Chip USBV1.1+V2.0 Enable the USB 1.1 and USB 2.0 controllers. (Default value)V1.1 Enable only the USB 1.1 controller.Disabled Disable the onboard USB controller.

USB Keyboard SupportEnabled Enable USB keyboard support.Disabled Disable USB keyboard support. (Default value)

USB Mouse SupportEnabled Enable USB mouse support.Disabled Disable USB mouse support. (Default value)

Onboard 1394Enabled Enable onboard IEEE 1394 function. (Default value)Disabled Disable this function.

Legacy USB storage detectThis option allows users to decide whether to detect USB storage devices, including USB flashdrives and USB hard drives during POST.

Enabled BIOS will scan all USB storage devices. (Default value)Disabled Disable this function.

Onboard Serial Port 1Auto BIOS will automatically setup the port 1 address.3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.Disabled Disable onboard Serial port 1.


Engl

ish

Onboard Parallel PortDisabled Disable onboard LPT port.378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port ModeSPP Using Parallel port as Standard Parallel Port. (Default value)EPP Using Parallel port as Enhanced Parallel Port.ECP Using Parallel port as Extended Capabilities Port.ECP+EPP Using Parallel port as ECP & EPP mode.

ECP Mode Use DMAThis option is available only when Parallel Port Mode is set to ECP or ECP+EPP.

3 Set ECP Mode Use DMA to 3. (Default value)1 Set ECP Mode Use DMA to 1.

BIOS Setup- 49 -

English

2-4 Power Management Setup

ACPI Suspend TypeS1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).

Soft-Off by Power buttonInstant-Off Press power button then Power off instantly. (Default value)Delay 4 Sec. Press power button 4 seconds to Power off. Enter suspend if button is pressed

less than 4 seconds.PME Event Wake Up

Disabled Disable this function.Enabled Enable PME Event Wake up. (Default value)

Modem Ring OnAn incoming call via modem can awake the system from any suspend state.

Disabled Disable this function.Enabled Enable Modem Ring On function. (Default value)

USB Resume from SuspendDisabled Disable this function. (Default value)Enabled Enable USB device wake up system from suspend mode.

Power-On by AlarmYou can enable the "Power-On by Alarm" item and key in Date/Time to power on system.

Disabled Disable this function. (Default value)Enabled Enable alarm function to POWER ON system.

If Power-On by Alarm is Enabled.Day of Month Alarm : Everyday, 1~31Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwarePower Management Setup

ACPI Suspend Type [S1(POS)]Soft-Off by Power button [Instant-Off]PME Event Wake Up [Enabled]Modem Ring On [Enabled]USB Resume from Suspend [Disabled]Power-On by Alarm [Disabled]

x Day of Month Alarm Everydayx Time (hh:mm:ss) Alarm 0 : 0 : 0

HPET Support (Note) [Enabled]Power On By Mouse [Disabled]Power On By Keyboard [Disabled]

x KB Power ON Password EnterAC Back Function [Soft-Off]


Item HelpMenu Level

(Note) Supported on Vista operating system only.


Engl

ish

HPET Support (Note)

Disabled Disable this function.Enabled Enable support for High Precision Event Timer (HPET) funtion. (Default value)

Power On By MouseDisabled Disable this function. (Default value)Double-Click Double click on PS/2 mouse left button to power on the system.

Power On By KeyboardDisabled Disable this function. (Default value)Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power

on the system.Any KEY Press any key to power on the system.Password Enter from 1 to 5 characters to set the Keyboard Power On Password.

KB Power ON PasswordWhen "Power On by Keyboard" is set to Password, you can set the password here.

Enter Input password (from 1 to 5 characters) and press Enter to set the KeyboardPower On password.

AC Back FunctionSoft-Off When AC-power back to the system, the system will be in "Off" state.

(Default value)Full-On When AC-power back to the system, the system always in "On" state.

(Note) Supported on Vista operating system only.

BIOS Setup- 51 -

English

2-5 PnP/PCI Configurations

PCI 1 IRQ AssignmentAuto Auto assign IRQ to PCI 1. (Default value)3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.



CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwarePnP/PCI Configurations

PCI 1 IRQ Assignment [Auto]PCI 2 IRQ Assignment [Auto]PCI 3 IRQ Assignment [Auto]


Item HelpMenu Level


Engl

ish

2-6 PC Health Status

Reset Case Open StatusDisabled Don't reset case open status. (Default value)Enabled Clear case open status at next boot.

Case OpenedIf the case is closed, Case Opened will show "No."If the case is opened, Case Opened will show "Yes."If you want to reset Case Opened value, enable Reset Case Open Status and save the changeto CMOS, and then your computer will restart.

Current Voltage(V) Vcore / DDR2 1.8V / +3.3V / +12VDetect system's voltage status automatically.

Current System/CPU TemperatureDetect system/CPU temperature automatically.

Current CPU/SYSTEM/POWER FAN Speed (RPM)Detect CPU/system/power fan speed status automatically.

CPU Warning Temperature60oC / 140oF Monitor CPU temperature at 60oC / 140oF.70oC / 158oF Monitor CPU temperature at 70oC / 158oF.80oC / 176oF Monitor CPU temperature at 80oC / 176oF.90oC / 194oF Monitor CPU temperature at 90oC / 194oF.Disabled Disable this function. (Default value)

CPU/SYSTEM/POWER FAN Fail WarningDisabled Disable CPU/system/power fan fail warning function. (Default value)Enabled Enable CPU/system/power fan fail warning function.

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwarePC Health Status

Reset Case Open Status [Disabled]Case Opened YesVcore OKDDR2 1.8V OK+3.3V OK+12V OKCurrent System Temperature 32oCCurrent CPU Temperature 45oCCurrent CPU FAN Speed 3245 RPMCurrent SYSTEM FAN Speed 0 RPMCurrent POWER FAN Speed 0 RPMCPU Warning Temperature [Disabled]CPU FAN Fail Warning [Disabled]SYSTEM FAN Fail Warning [Disabled]POWER FAN Fail Warning [Disabled]CPU Smart FAN Control [Enabled]CPU Smart FAN Mode [Auto]System Smart FAN Control [Enabled]


Item HelpMenu Level

BIOS Setup- 53 -

English

CPU Smart FAN Control(Note)

Disabled Disable this function.Enabled When this function is enabled, CPU fan will run at different speed depending

on CPU temperature. Users can adjust the fan speed with Easy Tunebased on their requirements. (Default value)

CPU Smart FAN ModeThis option is available only when CPU Smart FAN Control is enabled.

Auto BIOS autodetects the type of CPU fan you installed and sets the optimalCPU Smart FAN control mode for it. (Default value)

Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable.PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable.

System Smart FAN ControlDisabled Disable this function. (Default value)Enabled When this function is enabled, system fan will run at different speed depend-

ing on system temperature. Users can adjust the fan speed with Easy Tunebased on their requirements.

(Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install.


Engl

ish

2-7 MB Intelligent Tweaker(M.I.T.)CMOS Setup Utility-Copyright (C) 1984-2007 Award Software

MB Intelligent Tweaker(M.I.T.)System Clock Setting [Press Enter]Robust Graphics Booster [Auto]CPU Clock Ratio (Note) [16X]******** System Voltage Optimized ********System Voltage Control [Manual]DDR2 Voltage Control [Normal]NB/PCIE Voltage [Normal]SB/PCIE Voltage [Normal]FSB Voltage Control [Normal]HT-Link Voltage [Normal]SB Standby Voltage [Normal]CPU Voltage Control [Normal]Normal CPU Vcore 1.40000V


Item HelpMenu Level

Incorrectly using these features may result in system instability or corruption.Doing a overclock or overvoltage on CPU, chipsets and memory modules may result indamages or shortened life expectancy to these components.Please be aware that the M.I.T. menu items are for power users only.


System Clock SettingCMOS Setup Utility-Copyright (C) 1984-2007 Award Software

System Clock SettingSLI-Ready Memory [Disable] DisableFSB-Memory Clock Mode [Auto]

x FSB-Memory Ratio Autox CPU Host Frequency (Mhz) Auto 133.3

Actual CPU Clock (Mhz) 133.3x Memory Frequency (Mhz) Auto 800.0

Actual Memory Clock (Mhz) 800.0

PCIE x16 Slot 1 Clock (Mhz) [Auto] 100PCIE x8 Clock (Mhz) [Auto] 100PCIE x16 Slot 2 Clock (Mhz) [Auto] 100


Item HelpMenu Level

BIOS Setup- 55 -

English

SLI-Ready MemoryAllows you to use SLI-ready memory. The option is configurable only when SLI-ready memoryis used.Options: Disable, CPUOC 0%~CPUOC 5%, CPUOC MAX and ExpertFSB-Memory Clock Mode

Auto BIOS will automatically setup the FSB-Memory Clock Mode. (Default value)Linked Set FSB-Memory Clock Mode to Linked.Unlinked Set FSB-Memory Clock Mode to Unlinked.

FSB-Memory RatioThis option is available only when FSB-Memory Clock Mode is Linked.

Auto BIOS will automatically setup the FSB-Memory Ratio. (Default value)1:1 Set FSB-Memory Ratio to 1:1.5:4 Set FSB-Memory Ratio to 5:4.3:2 Set FSB-Memory Ratio to 3:2.Sync Mode Set FSB-Memory Ratio to Sync Mode.

CPU Host FrequencyThis option is available only when FSB-Memory Clock Mode is Linked or Unlinked.

100 ~ 650 Set CPU Host Frequency from 100 MHz to 650 MHz.The actual range depends on the CPU you install.If you use a 533 MHz FSB processor, please set CPU Host Frequency to 133 MHz.If you use an 800 MHz FSB processor, please set CPU Host Frequency to 200 MHz.If you use a 1066 MHz FSB processor, please set CPU Host Frequency to 266 MHz.If you use a 1333 MHz FSB processor, please set CPU Host Frequency to 333 MHz.Actual CPU Clock (Mhz)The values depend on CPU Host Frequency setting.Memory Frequency (Mhz)This option is available only when FSB-Memory Clock Mode is Unlinked.

400 ~ 1400 Set Memory Frequency from 400 MHz to 1400 MHz.Actual Memory Clock (Mhz)The values depend on Memory Frequency setting.PCIE x16 Slot 1 Clock (Mhz)

Auto BIOS will automatically setup the PCIE x16 Slot 1 Clock. (Default value)100 ~ 150 Set PCIE x16 Slot 1 Clock from 100 Mhz to 150 Mhz.

PCIe x8 Clock (Mhz)Auto BIOS will automatically setup the PCIE x8 Clock. (Default value)100 ~ 150 Set PCIE x8 Clock from 100 Mhz to 150 Mhz.

PCIE x16 Slot 2 Clock (Mhz)Auto BIOS will automatically setup the PCIE x16 Slot 2 Clock. (Default value)100 ~ 150 Set PCIE x16 Slot 2 Clock from 100 Mhz to 150 Mhz.


Engl

ish

Robust Graphics BoosterSelect the options can enhance the VGA graphics card bandwidth to get higher performance.

Auto Set Robust Graphics Booster to Auto. (Default value)Fast Set Robust Graphics Booster to Fast.Turbo Set Robust Graphics Booster to Turbo.

CPU Clock Ratio (Note)

This setup option will automatically assign by CPU detection.The option will display "Locked" and read only if the CPU ratio is not changeable.System Voltage ControlDetermines whether to manually set the system voltages. Auto lets BIOS automatically set thesystem voltages as required. Manual allows all voltage control items below to be configurable.(Default: Manual)DDR2 Voltage ControlPlease note that by overclocking your system through the increase of the DDR2 voltage, damageto the memory may occur.

Supports adjustable DDR2 voltage from 1.825V to 2.575V. (Default value: Normal)NB/PCIE VoltageSet the voltage settings for Northbridge, its PCI Express bus voltage.

Normal Set NB/PCIE voltage to Normal. (Default value)+0.05V~+0.20V Set NB/PCIE voltage to +0.05V~+0.20V.

SB/PCIE VoltageSet the voltage settings for Southbridge, its PCI Express bus voltage.

Normal Supply SB/PCIE voltage as Chipset requires. (Default value)+0.05V~+0.55V Set SB/PCIE voltage to +0.05V~+0.55V.

FSB Voltage ControlNormal Supply FSB voltage as FSB required. (Default value)+0.05V ~ +0.35V Increase FSB voltrage by 0.05V to 0.35V.

HT-Link VoltageSet the voltage settings for the HT-Link between Southbridge and Northbridge.

Normal Supply HT-Link voltage as HT-Link requires. (Default value)+0.05V~+0.35V Set HT-Link voltage to +0.05V~+0.35V.

SB Standby VoltageSet the Southbridge standby voltage.

Normal Supply standby voltage as Southbridge requires. (Default value)+0.10V~+0.20V Set Southbridge standby voltage to +0.10V~+0.20V.

CPU Voltage ControlSupports adjustable CPU vcore. The adjustable range is dependent on CPUs.

(Default value: Normal)Please note that by overclocking your system through the increase of the CPU voltage, damageto the CPU or decrease in the CPU life expectancy may occur.Normal CPU Vcore

Display your CPU's normal voltage.

BIOS Setup- 57 -

English

2-9 Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automati-cally detects.

2-8 Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimumsystem performance.




Load Optimized Defaults


Load Optimized Defaults (Y/N)? N




Load Fail-Safe Defaults


Load Fail-Safe Defaults (Y/N)? N


Engl

ish

2-10 Set Supervisor/User Password

When you select this function, the following message will appear at the center of the screen to assistyou in creating a password.Type the password, up to eight characters, and press <Enter>. You will be asked to confirm thepassword. Type the password again and press <Enter>. You may also press <Esc> to abort theselection and not enter a password.To disable password, just press <Enter> when you are prompted to enter password. A message"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password isdisabled, the system will boot and you can enter Setup freely.The BIOS Setup program allows you to specify two separate passwords:SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOSSetup program function. When enabled, the Supervisor password is required for entering the BIOSSetup program and having full configuration fields, the User password is required to access only basicitems.If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be promptedfor the password every time the system is rebooted or any time you try to enter Setup Menu.If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted onlywhen you try to enter Setup.




Change/Set/Disable Password


Enter Password:

BIOS Setup- 59 -

English

2-12 Exit Without Saving

Type "Y" will quit the Setup Utility without saving to RTC CMOS.Type "N" will return to Setup Utility.

2-11 Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.Type "N" will return to Setup Utility.




Abandon all Data


Quit Without Saving (Y/N)? N




Save Data to CMOS


Save to CMOS and EXIT (Y/N)? Y


Engl

ish

Drivers Installation- 61 -

English

Chapter 3Drivers Installation

After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers thatrecommended to install. Please pick the item that you want and press "install" followed the item; or you canpress "Xpress Install" to install all items defaulted.

Pictures below are shown in Windows XP.Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driverCD-title will auto start and show the installation guide. If not, please double click the CD-ROMdevice icon in "My computer", and execute the Run.exe.

Some device drivers will restart your system automatically. Afterrestarting your system the "Xpress Install" will continue to install otherdrivers.System will reboot automatically after install the drivers, afterward you caninstall others application.

For USB2.0 driver support under Windows XP operating system, pleaseuse Windows Service Pack. After install Windows Service Pack, it will showa question mark "?" in "Universal Serial Bus controller" under "DeviceManager". Please remove the question mark and restart the system (Systemwill auto-detect the right USB2.0 driver).

3-1 Install Chipset Drivers


Engl

ish

3-2 Software ApplicationsThis page displays all the tools that Gigabyte developed and some free software, you can choose anyoneyou want and press "install" to install them.

3-3 Driver CD InformationThis page lists the contents of software and drivers in this CD-title.

Drivers Installation- 63 -

English

3-4 Hardware InformationThis page lists all device you have for this motherboard.

3-5 Contact UsPlease see the last page for details.


Engl

ish

Appendix- 65 -

English

Chapter 4 Appendix4-1 Unique Software Utilities(Not all model support these Unique Software Utilities, please check your MB features.)

4-1-1 EasyTune 5 IntroductionEasyTune 5 presents the most convenient Windows based system performance enhancement andmanageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancingsystem performance, 2) C.I.A. and M.I.B. for special enhancement for CPU and Memory, 3) Smart-Fancontrol for managing fan speed control of both CPU cooling fan and North-Bridge Chipset cooling fan, 4) PChealth for monitoring system status.(Note)

User Interface Overview

(Note) EasyTune 5 functions may vary depending on different motherboards.

Button / Display Description1. Overclocking Enters the Overclocking setting page2. C.I.A. and M.I.B. Enters the C.I.A. and M.I.B. setting page3. Smart-Fan Enters the Smart-Fan setting page4. PC Health Enters the PC Health setting page5. GO Confirmation and Execution button6. "Easy Mode" & "Advance Mode" Toggles between Easy and Advance Mode7. Display screen Display panel of CPU frequency8. Function display LEDs Shows the current functions status9. GIGABYTE Logo Log on to GIGABYTE website10. Help button Display EasyTuneTM 5 Help file11. Exit or Minimize button Quit or Minimize EasyTuneTM 5 software


Engl

ish

4-1-2 Xpress Recovery2 IntroductionXpress Recovery2 is designed to provide quick backup and restora-tion of hard disk data. Supporting Microsoft operating systems includingWindows XP/2000/NT/98/Me and DOS, and file systems includingFAT16, FAT32, and NTFS, Xpress Recovery2 is able to back up data

How to use the Xpress Recovery2Initial access by booting from CD-ROM and subsequent access by pressing the F9 key:Steps: After entering BIOS Setup, go to Advanced BIOS Feature and set to boot from CD-ROM. Save

the settings and exit the BIOS Setup. Insert the provided driver CD into your CD-ROM drive. Uponsystem restart, the message which says "Boot from CD/DVD:" will appear in the bottom left cornerof the screen. Press any key to enter Xpress Recovery2.After the steps above are completed, subsequent access to Xpress Recovery2 can be madeby simply pressing the <F9> key during system power-on.

1. If you have already entered Xpress Recovery2 by booting from the CD-ROM, you canenter Xpress Recovery2 by pressing the <F9> key in the future.

2. System storage capacity and the reading/writing speed of the hard disk will affectthe data backup speed.

3. It is recommended that Xpress Recovery2 be immediately installed once you com-plete installations of OS and all required drivers as well as software.

on hard disks on PATA and SATA IDE controllers. After Xpress Recovery2 is executed from CD-ROMfor the first time, it will stay permanent in your hard disk. If you wish to run Xpress Recovery2 later, youcan simply press F9 during system bootup to enter Xpress Recovery2 without the CD-ROM.

System requirements:1. Intel x86 platforms2. At least 64M bytes of system memory3. VESA-supported VGA cards

Boot from CD/DVD:..Boot from CD/DVD:Press any key to startup XpressRecovery2.....

<F9>: Xpress Recovery2

Award Modular BIOS v6.00PG, An Energy Star AllyCopyright (C) 1984-2007, Award Software, Inc.

GA-N680SLI-DQ6 FAa....

<DEL>:BIOS Setup/Dual BIOS <F9>: Xpress Recovery2 <F12>: Boot Menu <End>: Qflash4 /12 /2007-NF68-6A61IG01C-00

Appendix- 67 -

English

1. RESTORE:Restore the backed-up data to your hard disk.(This button will not appear if there is no backupfile.)

2. BACKUP:Back up data from hard disk.

3. REMOVE:Remove previously-created backup filesto release disk space.(This button will not appear if there is no backupfile.)

4. REBOOT:Exit the main screen and restart the system.

The Main Screen of Xpress Recovery2

Limitations:1. Not compatible to Xpress Recovery.2. For the use of Xpress Recovery2, a primary partition must be reserved.3. Xpress Recovery2 will store the backup file at the end of the hard disk, so free space available

on the hard disk for the backup file must be allocated in advance. (A minimum 4GB is recom-mended but the actual space is dependent on the size of the data to be backed up)

4. Capable of backing up hard disks installed with Windows operating systems including DOS andWindows XP/2000/NT/9x/Me.

5. USB hard disks are currently not supported.6. Does not support RAID/AHCI (class code 0104/0106) hard disks.7. Capable of backing up and restoring only the first physical hard disk.Hard disks detection sequence is as follows:

a. PATA IDE primary channelb. PATA IDE secondary channelc . SATA IDE channel 1d. SATA IDE channel 2e. SATA IDE channel 3f. SATA IDE channel 4

Precautions:1. When using hard disks with more than 128 GB under Windows 2000, be sure to execute the

EnableBigLba.exe program from the driver CD before data backup.2. It is normal that data backup takes longer time than data restoration.3. Xpress Recovery2 is compliant with the GPL regulations.4. On a few motherboards based on Nvidia chipsets, BIOS update is required for Xpress Recovery2

to correctly identify RAID and SATA IDE mode. Please contact your motherboard manufacturer.


Engl

ish

4-1-3 Flash BIOS Method Introduction

A. What is Dual BIOS Technology ?Dual BIOS means that there are two system BIOS (ROM) on themotherboard, one is the Main BIOS and the other is Backup BIOS.

B. How to use Dual BIOS and Q-Flash Utility?a. After power on the computer, pressing <Del> immediately during POST (Power On Self Test) it willallow you to enter Award BIOS CMOS SETUP, then press <F8> to enter Dual BIOS / Q-Flash utility.

Under the normal circumstances, the system works on the Main BIOS. If the Main BIOS is corrupted ordamaged, the Backup BIOS can take over while the system is powered on. This means that your PCwill still be able to run stably as if nothing has happened in your BIOS.

b. Dual BIOS / Q-Flash Programming Utility





Time, Date, Hard Disk Type...

Dual BIOS Utility V2.02Boot From................................................. Main BiosMain ROM Type/Size............................... SST 49LF004A 512KBackup ROM Type/Size........................... SST 49LF004A 512K

Wide Range Protection DisableBoot From Main Bios

Auto Recovery EnableHalt On Error Disable

Keep DMI Data EnableCopy Main ROM Data to Backup

Load Default SettingsSave Settings to CMOS

Q-Flash UtilityUpdate Main BIOS from Drive

Update Backup BIOS from DriveSave Main BIOS to Drive

Save Backup BIOS to DrivePgDn/PgUp: Modify : Move ESC: Reset F10: Power Off

Appendix- 69 -

English

c . Dual BIOS Item explanation:Wide Range Protection: Disable(Default), EnableStatus 1:If any failure (ex. Update ESCD failure, checksum error or reset? occurs in the Main BIOS, just beforethe Operating System is loaded and after the power is on, and that the Wide Range Protection is set to"Enable", the PC will boot from Backup BIOS automatically.Status 2:If the ROM BIOS on peripherals cards(ex. SCSI Cards, LAN Cards,..) emits signals to request restartof the system after the user make any alteration on it, the boot up BIOS will not be changed to theBackup BIOS.Boot From : Main BIOS(Default), Backup BIOSStatus 1:

The user can set to boot from Main BIOS or Backup BIOS.Status 2:

If one of the Main BIOS or the Backup BIOS fails, this item "Boot From : Main BIOS(Default)" willbecome gray and will not be changed by user.

Auto Recovery : Enable(Default), DisableWhen one of the Main BIOS or Backup BIOS occurs checksum failure, the working BIOS will automati-cally recover the BIOS of checksum failure.(In the Power Management Setup of the BIOS Setting, if ACPI Suspend Type is set to Suspend to RAM,the Auto Recovery will be set to Enable automatically.)(If you want to enter the BIOS setting, please press "Del" key when the boot screen appears.)Halt On Error : Disable(Default), EnableIf the BIOS occurs a checksum error or the Main BIOS occurs a WIDE RANGE PROTECTION error andHalt On Error set to Enable, the PC will show messages on the boot screen, and the system will pauseand wait for the user's instruction.

If Auto Recovery :Disable, it will show <or the other key to continue.>If Auto Recovery :Enable, it will show <or the other key to Auto Recover.>

Keep DMI Data : Enable(Default), DisableEnable: The DMI data won't be replaced by flashing new BIOS.(recommend)Disable: The DMI data will be replaced by flashing new BIOS.Copy Main ROM Data to Backup(If you boot from Backup ROM, this item will change to Copy Backup ROM Data to Main)Auto recovery message:

BIOS Recovery: Main to BackupThe means that the Main BIOS works normally and could automatically recover the Backup BIOS.

BIOS Recovery: Backup to MainThe means that the Backup BIOS works normally and could automatically recover the Main BIOS.(This auto recovery utility is set by system automatically and can’t be changed by user.)Load Default SettingsLoad dual BIOS default value.Save Settings to CMOSSave revised setting.


Engl

ish

Before Use:Follow the steps below before using Q-Flash to update BIOS:1. From GIGABYTE's website, download the latest compressed BIOS update file that matches your

motherboard model2. Extract the downloaded BIOS files and save the new BIOS file (e.g. N680SDQ6.F1) to your floppy

diskor hard disk. Note: Q-Flash only supports hard disks or flash drives using FAT32/16/12 file system.3. Restart the system. During BIOS POST, press the End key to enter Q-Flash. NOTE: Press the

End key to enter Q-Flash if you wish to use hard drives in RAID/AHCI mode or hard drivesattached to the independent IDE/SATA controller.

Step 1:a. In the Dual BIOS / Q-Flash menu, use the UP or DOWN ARROW key to select Update Main BIOS

from Drive and press ENTER.

If you wish to back up the current BIOS file, use the Save Main BIOS to Drive function.

Updating the BIOS

Because BIOS flashing is potentially risky, please do it with caution and avoid inadequateoperation that may result in system malfunction.

Method 1 : Q-FlashTM

Q-FlashTM is a BIOS update tool that allows the user to update BIOSwithout entering operating systems like MS-DOS or Windows.Em-bedded in the BIOS, the Q-FlashTM tool frees you from the hassles of

going through complicated BIOS flashing process.

Award Modular BIOS v6.00PG, An Energy Star AllyCopyright (C) 1984-2007, Award Software, Inc.

GA-N680SLI-DQ6 FAa....

<DEL>:BIOS Setup/Dual BIOS <F9>: Xpress Recovery2 <F12>: Boot Menu <End>: Qflash4 /12 /2007-NF68-6A61IG01C-00

<End>: Qflash

Appendix- 71 -

English

b. Select the floppy drive or hard drive where the BIOS file is saved, such as "Floppy A" andpress ENTER.









0 file(s) foundFloppy A <Drive>HDD 0-0 <Drive>

Total size : 0 Free size : 0F5 : Refresh DEL : Delete

Step 2: The process of system reading the BIOS file from the floppy disk is displayed on the screen.When the message "Are you sure to update BIOS?" appears, press ENTER. The BIOS updatewill begin and the current process will be displayed.

1. Do not turn off or restart the system when the system is reading/updating the BIOS.2. Do not remove the floppy disk or hard drive/USB drive when the system is updating the BIOS.

Step 3: When the update process is complete, press any key to return to the Dual BIOS / Q-Flash mainmenu.

c . Select the BIOS file and press ENTER.

Make sure again the BIOS file matches your motherboard model.









!! Copy BIOS completed - Pass !!

Please press any key to continue


Engl

ish

Step 4: Press ESC and then ENTER to exit Dual BIOS / Q-Flash and the system will restart. As thesystem reboots, you will see the new BIOS version during POST.

Step 5: As the system reboots, press DELETE to enter BIOS Setup. Select Load Optimized De-faults and press ENTER to load BIOS defaults. System will re-detect all peripherals devicesafter BIOS update, so we recommend that you reload BIOS defaults.

Press Y to load BIOS defaults

Step 6: Select Save & Exit Setup and then press Y to save settings to CMOS and exit BIOS Setup.When the system restarts, the whole update process is complete.




Load Optimized Defaults


Load Optimized Defaults (Y/N)? Y

Appendix- 73 -

English

Method 2 : @BIOSTM UtilityIf you do not have a DOS startup disk, we recommend that you use thenew @BIOS utility. @BIOS allows users to update their BIOS underWindows. Just select the desired @BIOS server to download the latestversion of BIOS.

1. Methods and steps:I. Update BIOS through Internet

a. Click "Internet Update" iconb. Click "Update New BIOS" iconc . Select @BIOSTM severd. Select the exact model name on your motherboarde. System will automatically download and update the BIOS.

II. Update BIOS NOT through Internet:a. Do not click "Internet Update" iconb. Click "Update New BIOS"c. Please select "All Files" in dialog box while opening the old file.d. Please search for BIOS unzip file, downloading from internet or any other methods (such

as: N680SDQ6.F1).e. Complete update process following the instruction.

Fig 1. Installing the @BIOS utility Fig 2. Installation Complete and Run @BIOS

Fig 3. The @BIOS Utility Fig 4. Select the desired @BIOS server

Click " " Click "Update New BIOS"

Select @BIOS item than click Install

Click Sart/ Programs/ GIGABYTE/@BIOS


Engl

ish

III. Save BIOSIn the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save thecurrent BIOS version.

IV. Check out supported motherboard and Flash ROM:In the very beginning, there is "About this program" icon shown in dialog box. It can help you check outwhich kind of motherboard and which brand of Flash ROM are supported.

2. Note:I. In method I, if it shows two or more motherboard's model names to be selected, please make

sure your motherboard's model name again. Selecting wrong model name will cause thesystem unbooted.

II. In method II, be sure that motherboard's model name in BIOS unzip file are the same as yourmotherboard's. Otherwise, your system won't boot.

III. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go ontoGigabyte's web site for downloading and updating it according to method II.

IV. Please note that any interruption during updating will cause system unbooted.V. Do not use @BIOS and C.O.M. (Corporate Online Management) at the same time.

Appendix- 75 -

EnglishTo configure SATA hard drive(s), follow the steps below:(1) Install SATA hard drive(s) in your system.(2) Configure SATA controller mode and boot sequence in BIOS Setup.(3) Configure RAID set in RAID BIOS. (Note 1)

(4) Make a floppy disk containing the SATA controller driver. (Note 1), (Note 2)

(5) Install the SATA controller driver during OS installation. (Note 1), (Note 2)

Before you beginPlease prepare:(a) At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two

hard drives with identical model and capacity). If you do not want to create RAID, you may prepareonly one hard drive.

(b) An empty formatted floppy disk.(c) Windows XP/2000 setup disk.(d) Driver CD for your motherboard.

A. nVIDIA® nForce 680i SLI Southbridge(1) Installing SATA hard drive(s) in your computerAttach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to availableSATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, referto the connectors introduction section of the user's manual to identify the SATA controller for theconnectors. (For example, on the GA-N680SLI-DQ6 motherboard, the SATAII0, SATAII1, SATAII2,SATAII3, SATAII4 and SATAII5 connectors are supported by the nVIDIA® nForce 680i SLI Southbridge.)Then connect the power connector from your power supply to the hard drive.

(Note 1) Required for setting up RAID array.(Note 2) Required when the SATA controller is set to AHCI Mode(Only for GIGABYTE SATA2

Controller).

4-1-4 Configuring SATA Hard Drive(s)


Engl

ish

Figure 1

To set up a RAID array, ensure that NV SATA RAID function is enabled (Figure 2), otherwise leaveit disabled. Then enable the SATA channels with hard disks that you want to use for RAID (for example,NV SATA1 Primary RAID controls the SATAII0 connector and NV SATA 1 Secondary RAID controlsthe SATAII1 connector) (Figure 2).

The BIOS Setup menus described in this section may not show the exact settings for yourmotherboard. The actual BIOS Setup menu options you will see shall depend on the motherboardyou have and the BIOS version.

Figure 2

(2) Configuring SATA controller mode and boot sequence in BIOS SetupMake sure to configure the SATA controller mode correctly in system BIOS Setup and set the first bootdevice.Step 1:Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In theexample in Figure 1, make sure that NV Serial-ATA Controller under the Integrated Peripheralsmenu is enabled. If you wish to create RAID array, press ENTER on the Serial-ATA RAID Config itemto enter the submenu .

CMOS Setup Utility-Copyright (C) 1984-2007 Award SoftwareSerial-ATA RAID Config

Item HelpMenu Level

NV SATA RAID function [Enabled]NV SATA 1 Primary RAID [Enabled]NV SATA 1 Secondary RAID [Enabled]NV SATA 2 Primary RAID [Disabled]NV SATA 2 Secondary RAID [Disabled]NV SATA 3 Primary RAID [Disabled]NV SATA 3 Secondary RAID [Disabled]



On-Chip IDE Channel0 [Enabled]IDE Prefetch Mode [Enabled]NV Serial-ATA Controller [All Enabled]Serial-ATA RAID Config [Press Enter]Onboard SATA-II Ctrl1 [Enabled]Onboard SATA-II Ctrl1 Mode [IDE]Onboard SATA-II Ctrl2 [Enabled]Onboard SATA-II Ctrl2 Mode [IDE]On-Chip MAC Lan [Auto]On-Chip MAC1 Lan [Auto]On-Chip SMART LAN [Press Enter]Onboard LAN1 Controller [Enabled]Onboard LAN2 Controller [Enabled]Onboard LAN Boot ROM [Disabled]Onboard Audio Function [Auto]On-Chip USB [V1.1+V2.0]USB Keyboard Support [Disabled]USB Mouse Support [Disabled]Onboard 1394 [Enabled]


Item HelpMenu Level

Appendix- 77 -

English

Step 3:Save and exit BIOS Setup.

Figure 3

Step 2:Set First Boot Device under the Advanced BIOS Features menu to CDROM to boot from CD-ROMafter system restarts (Figure 3).


Hard Disk Boot Priority [Press Enter]First Boot Device [CDROM]Second Boot Device [Hard Disk]Third Boot Device [CDROM]Password Check [Setup]HDD S.M.A.R.T. Capability [Disabled]CPU Hyper-Threading [Enabled]Limit CPUID Max. to 3 [Disabled]No-Execute Memory Protect [Enabled]CPU Enhanced Halt (C1E) [Enabled]CPU Thermal Monitor 2(TM2) [Enabled]CPU EIST Function [Enabled]Virtualization Technology [Enabled]Full Screen LOGO Show [Enabled]Init Display First [PEG]


Item HelpMenu Level


Engl

ish

(3) Configuring RAID set in RAID BIOSEnter the RAID BIOS setup utility to configure a RAID array. Skip this step if you do not want to createRAID.

Step 1:After the POST memory test begins and before the operating system boot begins, look for a messagewhich says "Press F10 to enter RAID setup utility" (Figure 4). Hit the F10 key to enter the RAID BIOSsetup utility.

Figure 4

Step 2:The Define a New Array screen is the first option screen when you enter the NVIDIA RAID setup utility.(Figure 5). You can press the TAB key to highlight through options.

Step 3:In the RAID Mode field, use the UP or DOWN ARROW key to select a RAID mode. The supported RAIDmodes include Mirroring (default), Striping, Stripe Mirroring, Spanning and RAID 5. The following is anexample of RAID 0 array creation.

Step 4:If RAID 0 (Striping) is selected, you can manually set the striping block size. In the Striping Block field,use the UP or DOWN ARROW key to set the Striping Block size. The KB is the standard unit of StripingBlock size. We recommend you leaving it to the default setting--Optimal (64K). The size range is from4K to 128K.

Figure 5

MediaShield ROM BIOS 6.93Copyright (C) 2006 NVIDIA Corp.

Detecting array ...

Press F10 to enter RAID setup utility ...

MediaShield Utility Nov 2 2006- Define a New Array -

RAID Mode: Striping Striping Block: Optimal

Free DisksPort Disk Model Capacity

1 ST3120026AS 111.79GB2 ST3120026AS 111.79GB

Array DisksPort Disk Model Capacity

[ ] Add

[ ] Del

[ESC] Quit [F6] Back [F7] Finish [TAB] Navigate [ ] Select [ENTER] Popup

Appendix- 79 -

English

Step 6:Press F7 after selecting the target hard disks. A message which says "Clear disk data?" will appear(Figure 7). If you are sure to clear the data in the selected hard drives, press Y. (If the hard drivescontain previously created RAID array, you need to press Y to clear the data from the hard drives.)

Figure 7

Figure 6

Step 5:Next, select the hard drives which you wish to be included in the disk array. The Free Disks sectiondisplays the information about the currently installed SATA hard drives. Press the TAB key to move tothe Free Disks section. Select the target hard drives using the UP or DOWN ARROW key and use theRIGHT ARROW key to add the hard drives to the Array Disks section (Figure 6).



[ ] Add

[ ] Del


1 ST3120026AS 111.79GB2 ST3120026AS 111.79GB



Clear disk data ?

[Y] YES [N] NO


[ ] Add

[ ] Del


1.0.M ST3120026AS 111.79GB1.1.M ST3120026AS 111.79GB




Clear disk data ?

[Y] YES [N] NO


Engl

ish

To read more information about the RAID array, press ENTER to enter the Array Detail screen (Figure9), where you should see detailed information about RAID mode, disk block size, disk model name,and disk capacity, etc.

Figure 9

Figure 8

After that, the Array List screen displaying the RAID array you created will appear (Figure 8).(Note: BBS stands for BIOS Boot Specification. This indicates that the boot device is defined in theBIOS.)

To delete the array, press D in the Array Detail screen. When the "Delete this array?" message appears,press Y to confirm or N to cancel. Press ENTER to return to the Array List screen.

To exit the Nvidia RAID utility, press ESC in the main menu or Ctrl+X in the Array List screen.

Now, you can proceed to install the SATA controller driver and operating system.

Array 1: NVIDIA STRIPE 233.57G- Array Detail -

RAID Mode: StripingStriping Width : 2 Striping Block: 64K

Port Index Disk Model Capacity

1.1 0 ST3120026AS 111.79GB1.0 1 ST3120026AS 111.79GB

[R] Rebuild [D] Delete [C] Clear Disk [ENTER] Return

MediaShield Utility Nov 2 2006- Array List -

[Ctrl-X] Exit [ ] Select [B] Set Boot [N] New Array [ENTER] Detail

Boot Status Vendor Array Model Name

BBS Healthy NVIDIA STRIPE 223.57G

Appendix- 81 -

English

(4) Making a SATA Driver DiskTo install operating system onto RAID disks successfully, you need to install the SATA RAID driverduring OS installation. Without the driver, the hard disk may not be recognized during the Windowssetup process. Skip this step if you do not want to create RAID. First of all, copy the driver for the SATAcontroller from the motherboard driver CD-ROM to a floppy disk. See the instructions below about howto copy the driver in MS-DOS mode(Note). Prepare a startup disk that has CD-ROM support and a blankformatted floppy disk.

Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from thestartup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\>prompt, type the following two commands. Press ENTER after each command (Figure 10):

cd bootdrv

menu

Step 2: When the controller menu (Figure 11) appears, remove the startup disk and insert the blankformatted disk. Select the controller driver by pressing the corresponding letter from the menu.For example, from the menu in Figure 11, press G to select (G) NVIDIA nFORCE 600 Series Raid(XP) if you wish to install Windows XP (32-bit). Your system will then automatically zip and transfer thisdriver file to the floppy disk. Press 0 to exit when finished.

(Note) For users without a startup disk:Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM. From the CD-ROMdrive folder, double click the MENU.exe file in the BootDrv folder (Figure 12). A command promptwindow will open similar to that in Figure 11.

Figure 10 Figure 11

Figure 12


Engl

ish

Figure 13

Windows Setup

Press F6 if you need to install a 3rd party SCSI or RAID driver.

Figure 14

Windows Setup

S=Specify Additional Device ENTER=Continue F3=Exit

Setup could not determine the type of one or more mass storage devicesinstalled in your system, or you have chosen to manually specify an adapter.Currently, Setup will load support for the following mass storage devices(s)

<none>

* To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

* If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

(5) Installing SATA controller driver during OS installationNow that you have prepared the SATA driver disk and configured BIOS settings, you are ready to installWindows 2000/XP onto your SATA hard drive with the SATA driver. The following is an example ofWindows XP installation.

Step 1: Restart your system to boot from the Windows 2000/XP Setup disk and press F6 as soon asyou see the "Press F6 if you need to install a 3rd party SCSI or RAID driver" message (Figure 13). Afterpressing F6, there will be a few moments of some files being loaded before you see the next screen.

Step 2:When a screen similar to that below appears, insert the floppy disk containing the SATA driver and pressS (Figure 14).

Appendix- 83 -

English

Step 3:If Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 15 belowwill appear. Use the ARROW keys to select NVIDIA RAID CLASS DRIVER (Figure 15) and pressENTER. Later, when a screen similar to Figure 16 appears, you must press S to select additionaldriver. The screen will return to previous screen as shown in Figure 15. Select NVIDIA nForceStorage Controller and press ENTER.

Figure 15

Figure 16

Windows Setup

S=Specify Additional Device Enter=Continue F3=Exit

Setup will load support for the following mass storage device(s):

NVIDIA RAID CLASS DRIVER (required)



If a message appears saying one or some file(s) cannot be found, please check the floppy diskor copy the correct SATA driver again from the motherboard driver CD.

Windows Setup

ENTER=Select F3=Exit

You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen.

NVIDIA RAID CLASS DRIVER (required)NVIDIA nForce Storage Controller (required)


Engl

ish

After the SATA controller driver installation is completed, you can proceed with the Windows 2000/XPinstallation.

Figure 18

WindowsXP Professional Setup

Welcome to Setup.This port of the Setup program prepares Microsoft(R)Windows (R) XP to run on your computer.

To set up Windows XP now, press ENTER.

To repair a Windows XP installation using Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

Enter= Continue R=Repair F3=Exit

(Note: Each time you add a new hard drive to a RAID array, the RAID driver will have to be installedunder Windows once for that hard drive. After that, the driver will not have to be installed.)

Step 4:When the next screen (Figure 17) appears, press ENTER to continue the SATA driver installation fromthe floppy disk.

Figure 17

Windows Setup



NVIDIA RAID CLASS DRIVER (required)NVIDIA nForce Storage Controller (required)



Appendix- 85 -

English

B. GIGABYTE SATA2 Controller

(1) Installing SATA hard drive(s) in your computerAttach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to availableSATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, referto the connectors introduction section of the user's manual to identify the SATA controller for theconnectors. (For example, on the GA-N680SLI-DQ6 motherboard, the GSATAII0, GSATAII1, GSATAII2and GSATAII3 connectors are supported by the GIGABYTE SATA2 controller.) Then connect the powerconnector from your power supply to the hard drive.

Figure 1

(2) Configuring SATA controller mode and boot sequence in BIOS SetupMake sure to configure the SATA controller mode correctly in system BIOS Setup and set the first bootdevce.

Step 1:Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In BIOSSetup, go to Integrated Periperals, ensure that the Onboard SATA-II Ctrl1 or Onboard SATA-IICtrl2 is enabled. Then set Onboard SATA-II Ctrl1 Mode or Onboard SATA-II Ctrl2 Mode to RAIDbefore configuring RAID. If you do not want to create RAID, set this item to IDE or AHCI, depending onyour need (Figure 1).

The BIOS Setup menus described in this section may not show the exact settings for yourmotherboard. The actual BIOS Setup menu options you will see shall depend on the motherboardyou have and the BIOS version.


On-Chip IDE Channel0 [Enabled]IDE Prefetch Mode [Enabled]NV Serial-ATA Controller [All Enabled]Serial-ATA RAID Config [Press Enter]Onboard SATA-II Ctrl1 [Enabled]Onboard SATA-II Ctrl1 Mode [RAID]Onboard SATA-II Ctrl2 [Enabled]Onboard SATA-II Ctrl2 Mode [RAID]On-Chip MAC Lan [Auto]On-Chip MAC1 Lan [Auto]On-Chip SMART LAN [Press Enter]Onboard LAN1 Controller [Enabled]Onboard LAN2 Controller [Enabled]Onboard LAN Boot ROM [Disabled]Onboard Audio Function [Auto]On-Chip USB [V1.1+V2.0]USB Keyboard Support [Disabled]USB Mouse Support [Disabled]Onboard 1394 [Enabled]


Item HelpMenu Level


Engl

ish

Step 2:To boot from Windows installation CD-ROM disk, set First Boot Device under the Advanced BIOSFeatures menu to CDROM (Figure 2).

Step 3:Save and exit BIOS Setup.

Figure 2


Hard Disk Boot Priority [Press Enter]First Boot Device [CDROM]Second Boot Device [Hard Disk]Third Boot Device [CDROM]Password Check [Setup]HDD S.M.A.R.T. Capability [Disabled]CPU Hyper-Threading [Enabled]Limit CPUID Max. to 3 [Disabled]No-Execute Memory Protect [Enabled]CPU Enhanced Halt (C1E) [Enabled]CPU Thermal Monitor 2(TM2) [Enabled]CPU EIST Function [Enabled]Virtualization Technology [Enabled]Full Screen LOGO Show [Enabled]Init Display First [PEG]


Item HelpMenu Level

Appendix- 87 -

English

(3) Configuring RAID array in RAID BIOSEnter the RAID BIOS setup utility to configure a RAID array. Skip this step if you do not want to createRAID.

Step 1:After the POST memory test begins and before the operating system boot begins, look for a messagewhich says "Press <Ctrl-G> to enter RAID Setup Utility" (Figure 3). Press CTRL+ G to enter theGIGABYTE SATA2 RAID BIOS setup utility.

Figure 3

Figure 4

GIGABYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS v1.06.59Copyright (C) 2005 GIGABYTE Technology. http://www.gigabyte.com

HDD0 : ST3120026AS 120 GB Non-RAIDHDD1 : ST3120026AS 120 GB Non-RAID

Press <Ctrl-G> to enter RAID Setup Utility ...

In the main screen of the GIGABYTE SATA2 RAID BIOS utility (Figure 4), use the UP or DOWN ARROWkey to highlight through choices. Highlight the item that you wish to execute and press ENTER.

GIGABYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.59

[ Main Menu ]

Create RAID Disk DriveDelete RAID Disk DriveRevert HDD to Non-RAIDSolve Mirror ConflictRebuild Mirror DriveSave And Exit SetupExit Without Saving

[ RAID Disk Drive List ]

[ TAB]-Switch Window [ ]-Select ITEM [ENTER]-Action [ESC]-Exit

[ Hard Disk Drive List ]

Mode Name Available Type/StatusHDD0: ST3120026AS 120 GB Non-RAIDHDD1: ST3120026AS 120 GB Non-RAID

Note: In the main screen, you can select a hard disk in the Hard Disk Drive List block and pressENTER. This allows you to check detailed information about the selected hard disk.


Engl

ish

Figure 6

A. Create Array:In the main screen, press ENTER on the Create RAID Disk Drive item. Then the RAID creation screenappears (Figure 5).


[ Create New RAID ]

Name: GRAID_Level: 0-StripeDisks: Select DiskBlock: 128 KBSize: 240 GB

Confirm Creation


[ ]-Move Cursor [DEL,BS]-Delete Character [ENTER]-Next [ESC]-Abort



[ Help ]Enter RAID Name

Enter a string between 1 to 16 charactersin length for the created RAID drive to beidentified by system BIOS or OS.

Figure 5


[ Create New RAID ]

Name: GRAIDLevel: 0-StripeDisks: Select DiskBlock: 128 KBSize: 240 GB

Confirm Creation


[ ]-Switch RAID Level [ENTER]-Next [ESC]-Abort



[ Help ]Select RAID Level

RAID 0 - Data striped for performanceRAID 1 - Data mirrored for redundancyJBOD - Data concatenated for huge

temporarily disk required

In the RAID creation screen, the Create New RAID block displays all the items that need to be set forcreating an array (Figure 5). The following procedure uses RAID 0 creation as an example.

Steps:1. Enter Array Name: Under the Name item, enter an array name with 1~16 letters (letters cannot be

special characters) and press ENTER.2. Select RAID Mode: Under the Level item, use UP or DOWN ARROW key to select RAID 0 (Stripe),

RAID 1 (Mirror), or JBOD (Figure 6). Then press ENTER to move onto the next step.

Appendix- 89 -

English

Figure 7

Figure 8

3. Assign Array Disks: After RAID mode is selected, RAID BIOS automatically assigns the two harddisks installed as the RAID disks.

4. Set Block Size (only for RAID 0): Under the Block item, use the UP or DOWN ARROW key toselect the block size (Figure 7), ranging from 4K to 128K. Press ENTER when finished.


[ Create New RAID ]


Confirm Creation


[ ]-Switch RAID Block Size [ENTER]-Next [ESC]-Abort



[ Help ]Setting Stripe Block

Select a stripe size which will be used todivide data from/to seperate RAID members.The following are typical values:

RAID 0-128KB

5. Set Array Size: Under the Size item, type the size of the array (Figure 8), and press ENTER.GIGABYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.59

[ Create New RAID ]


Confirm Creation


[ ]-Switch Unit [DEL,BS]-Delete Number [ENTER]-Next [ESC]-Abort



[ Help ]Setting RAID Capacity

Enter the RAID capacity. The default valueindicates the maximum capacity determinedby the selected members. If less than themaximum capacity is chosen, the remainingcapacity would be no used.


Engl

ish

Figure 9

Figure 10

6. Confirm Creation: After all of the items are configured, the selection bar automatically jumps to theConfirm Creation item. When prompted to confirm your selections (Figure 9), press Y to confirmor N to abort.


[ Create New RAID ]


Confirm Creation




[ Help ]

CONFIRM RAID CREATION

ALL DATA ON THE SELECTED HARD DISKWILL BE LOST WHEN EXIT WITH SAVING

Create RAID on the select HDD(Y/N)?Y

[ ]-Switch Unit [DEL,BS]-Delete Number [ENTER]-Next [ESC]-Abort


[ Main Menu ]



[ TAB]-Switch Window [ ]-Select RAID [ENTER]-Action [ESC]-Exit


Mode Name Available Type/StatusHDD0: ST3120026AS 120 GB RAID InsideHDD1: ST3120026AS 120 GB RAID Inside

Model Name RAID Level Capacity Status Members(HDDx)RDD0: GRAID 0-Stripe 240 GB Normal 01

When finished, the new RAID array will be displayed in the RAID Disk Drive List block (Figure 10).

Appendix- 91 -

English

Figure 11

Figure 12


[ Main Menu ]



[ TAB]-Switch Window [ ]-Select RAID [ENTER]-Detail [ESC]-Exit




[ RAID Information ]Name: JRAIDLevel: 0-StripeBlock: 128KB

Capacity: 240GB

Members: HDD 01Status: Normal

To check more detailed information about the array, use the TAB key while in the Main Menu block tomove the selection bar to the RAID Disk Drive List block. Select the array and press ENTER.A small window displaying the array information will appear in the center of the screen (Figure 11).


[ Main Menu ]






Save to Disk & Exit (Y/N)?Y

[ TAB]-Switch Window [ ]-Select ITEM [ENTER]-Action [ESC]-Exit

After configuring the RAID array, select the Save And Exit Setup item in the main screen to save yoursettings if you wish to exit the RAID BIOS utility, then press Y (Figure 12).


Engl

ish


[ Main Menu ]



[ ]-Select RAID [SPACE]-Mark Delete [DEL]-Confirm [ESC]-Abort


Mode Name Available Type/StatusHDD0: ST3120026AS 120 GB InsideHDD1: ST3120026AS 120 GB Inside

Model Name RAID Level Capacity Status Members(HDDx) RDD0: GRAID 0-Stripe 240 GB Normal 01


[ Main Menu ]



[ ]-Select RAID [SPACE]-Mark Delete [DEL]-Confirm [ESC]-Abort


Mode Name Available Type/StatusHDD0: ST3120026AS 120 GB InsideHDD1: ST3120026AS 120 GB Inside

Model Name RAID Level Capacity Status Members(HDDx) RDD0: GRAID 0-Stripe 240 GB Normal 01

ALL DATA ON THE RAID WILL LOST!!ARE YOU SURE TO DELETE (Y/N)? N

Figure 13

Figure 14

B. Delete Array:To delete the array, select Delete RAID Disk Drive in the main menu and press ENTER. The selectionbar will move to the RAID Disk Drive List block. Press the SPACEBAR on the array to be deleted; asmall triangle will appear to mark the selected array (Figure 13). Press Del.

Press Y to confirm yes to the following message (Figure 14) or N to cancel.

Now, you can proceed to install the SATA controller driver and operating system.

Appendix- 93 -

English

(4) Making a SATA Driver Disk (Required for AHCI and RAID Mode)To install operating system onto a serial ATA hard disk successfully, you need to install the SATAcontroller driver during OS installation. Without the driver, the hard disk may not be recognized duringthe Windows setup process. First of all, copy the driver for the SATA controller from the motherboarddriver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOSmode(Note 1). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk.

Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from thestartup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\>prompt, type the following two commands. Press ENTER after each command (Figure 15):

cd bootdrv

menu

Step 2: When the controller menu (Figure 16) appears, remove the startup disk and insert the blankformatted disk. Select the controller driver by pressing the corresponding letter from the menu.For example, from the menu in Figure 16, press I to select I) GIGABYTE 32Bit SATA-RAID Driver forWindows operating system(Note 2). Your system will then automatically zip and transfer this driver file tothe floppy disk. Press 0 to exit when finished.

(Note 1) For users without a startup disk:Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM. From theCD-ROM drive folder, double click the MENU.exe file in the BootDrv folder (Figure 17).A command prompt window will open similar to that in Figure 16.

Figure 15 Figure 16

Figure 17

(Note 2) For 64-bit Windows Operating System, please select GIGABYTE 64Bit SATA-RAID Driver .


Engl

ish

Figure 18

Figure 19

(5) Installing SATA controller driver during OS installation(Required for AHCI and RAID Mode)

Now that you have prepared the SATA driver disk and configured BIOS settings, you are ready to installWindows 2000/XP onto your SATA hard drive with the SATA driver. The following is an example ofWindows XP installation.

Step 1: Restart your system to boot from the Windows 2000/XP Setup disk and press F6 as soon asyou see the "Press F6 if you need to install a 3rd party SCSI or RAID driver" message (Figure 18). Afterpressing F6, there will be a few moments of some files being loaded before you see the next screen.

Step 2:When a screen similar to that below appears, insert the floppy disk containing the SATA driver and pressS (Figure 19).

Windows Setup

Press F6 if you need to install a third party SCSI or RAID driver.

Windows Setup


Setup could not determine the type of one or more mass storage devicesinstalled in your system, or you have chosen to manually specify an adapter.Currently, Setup will load support for the following mass storage devices(s)

<none>



Appendix- 95 -

English

Step 3:When Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 20below will appear. Use the ARROW keys to select one of the items displayed depending on theoperating system to be installed. For example, select GIGABYTE GBB363 RAID Controller (Windows2K/XP/2003) (Note) if you wish to install Windows XP (32-Bit). Then press ENTER.

Figure 20

Figure 21

If a message appears saying one or some file(s) cannot be found, please check the floppy diskor copy the correct SATA driver again from the motherboard driver CD.

Step 4:When the next screen (Figure 21) appears, press ENTER to continue the SATA driver installation fromthe floppy disk.

Windows Setup

ENTER=Select F3=Exit

You have chosen to configure a SCSI Adapter for use with Windows,using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESCto return to the previous screen.

GIGABYTE GBB363 RAID Controller (Windows 2K/XP/2003)GIGABYTE GBB363 AHCI Controller (Windows 2K/XP/2003)GIGABYTE GBB360 RAID Controller (Windows 2K/XP/2003)GIGABYTE GBB360 AHCI Controller (Windows 2K/XP/2003)

Windows Setup



GIGABYTE GBB363 RAID Controller (Windows 2K/XP/2003)



(Note) If you set the Onboard SATA-II Ctrl1 Mode or Onboard SATA-II Ctrl2 Mode item in BIOSSetup to AHCI mode, please select GIGABYTE GBB363 AHCI Controller (Windows 2K/XP/ 2003).


Engl

ish

Step 5:After the SATA controller driver installation is completed, you can proceed with the Windows XPinstallation.

Figure 22

WindowsXP Professional Setup

Enter= Continue R=Repair F3=Exit

Welcome to Setup.This port of the Setup program prepares Microsoft(R)Windows (R) XP to run on your computer.

To set up Windows XP now, press ENTER.

To repair a Windows XP installation using Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

Appendix- 97 -

English

4-1-5 2- / 4- / 6- / 8- Channel Audio FunctionIntroduction

STEP 1 :After installation of the audio driver, you should findan Audio Manager icon in your system tray(you can also find the icon in Control Panel). Double-click the icon to open the Audio Control Panel.

Note that if you wish to connect a microphone, you MUST connect it to the default Mic In jackfor the microphone to work correctly.

The default speaker settings for the 6 audio jacks areas shown in the picture to the right. The jackretasking capability supported by HD Audio allowsusers to change the function for each audio jack bythe audio software provided. For example, if arear speaker is plugged into the center/subwooferspeaker out jack, you can change the center/subwoofer speaker out jack to fucntion as a rearspeaker out jack via the audio software.Pleasefollow the steps to install the function. (Followingpictures are in Windows XP)

HD AudioWith multiple built-in high quality digital-to-analog converters (DACs) that support audio output at up to192 kHz/24-bit quality and multi-streaming applications, HD Audio is able to handle multiple audiostreams (in and out) simultaneously. Multi-channel audio experiences have become a reality so youcan, for instance, listen to MP3 music, have an Internet chat, make a telephone call over the Internet,and etc. all at the same time.

Stereo Speakers Connection and Settings:We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereooutput is applied.

Line In

Line Out(Front Speaker Out)

Mic In

Rear Speaker Out

Center/SubwooferSpeaker Out

Side SpeakerOut


Engl

ish

STEP 3:After a speaker or headphone is plugged into therear Line Out jack, a small window will pop up andask you what type of equipment is connected.Choose Headphone or Line Out depending onthe device connected and click OK. The 2-chan-nel audio setup is completed.

STEP 2:In the Audio Control Panel, click the Audio I/O tab.In the upper left list, click 2CH Speaker.

4 Channel Audio SetupSTEP 1 :After installation of the audio driver, you should findan Audio Manager icon in your system tray(you can also find the icon in Control Panel). Double-click the icon to open the Audio Control Panel.


Appendix- 99 -

English

6 Channel Audio SetupSTEP 1 :After installation of the audio driver, you should findan Audio Manager icon in your system tray(you can also find the icon in Control Panel). Double-click the icon to open the Audio Control Panel.

STEP 3:After plugging in 4-channel speakers to the rearspeaker jacks, a small window will pop up andask you what type of equipment is connected.Choose a device depending on the type of speakerconnected (4-channel audio consists of FrontSpeaker Out (Line Out) and Rear Speaker Out) andthen cl ick OK. The 4-channel audio setup iscompleted.


STEP 3:After plugging in 6-channel speakers to the rearspeaker jacks, a small window will pop up andask you what type of equipment is connected.Choose a device depending on the type of speakerconnected (6-channel audio consists of FrontSpeaker Out (Line Out), Rear Speaker Out, andCenter/Subwoofer Speaker Out) then click OK.The 6-channel audio setup is completed.


Engl

ish

8 Channel Audio Setup

STEP 1 :After installation of the audio driver, you should findan Audio Manager icon in your system tray(you can also find the icon in Control Panel). Double-click the icon to open the Audio Control Panel.


STEP 3:After plugging in 8-channel speakers to the rearspeaker jacks, a small window will pop up andask you what type of equipment is connected.Choose a device depending on the type of speakerconnected (8-channel audio consists of FrontSpeaker Out (Line Out), Rear Speaker Out, Cen-ter/Subwoofer Speaker Out, and Side Speaker Out)then cl ick OK. The 8-channel audio setup iscompleted.

Appendix- 101 -

English

Sound Effect Configuration:At the Sound Effect menu, users can adjust soundoption settings as desired.

AC'97 Audio Configuration:To enable the front panel audio connector tosupport AC97 Audio mode, go to the Audio ControlPanel and click the Audio I/O tab. In theANALOG area, click the Tool icon and then selectthe Disable front panel jack detection checkbox. This action completes the AC'97 Audioconfiguration.


Engl

ish

1. : This button provides you more controls over "dts NEO : PC". Music Mode ; Cinema Mode

2. "dts NEO : PC" :Press this button to enable or disable the dts NEO : PC function.Enabling dts NEO : PC allows the system to transform ordinary 2-channel stereo content into 4-,6-, or 8- channel surround sound, depending on your speaker configurations.

3. "dts INTERACTIVE" :If your surround sound system is connected via an external decoder, click the Audio I/O tab in theAudio Control Panel. Either click DTS Interactive in the upper left list or click the dts INTERACTIVE

button at the center bottom of the Audio ControlPanel. And click the dts NEO : PC button.The system will then simulate 5.1 channelsurround sound playback from two-channelcontent.

Enabling the DTS (Digital Theater Systems) functionBefore DTS is enabled, you would get only 2-channel output signals (from thefront speakers) when playing 2-channel music. You must play 4-, 6-, or 8-channel music sources to produce 4-, 6-, or 8- channel audio effects.

With DTS enabled, the system will transform two-channel stereo source material into multi-channelaudio output, creating a virtual surround sound environment(Note).

After installing the audio driver, at the center bottom of the Audio ControlPanel, you should find the DTS control button as shown below:

(Note) When DTS Interactive is enabled, only digital auio output (S/PDIF) is working, and you willnot hear sound from analog speaker or headphone.

DTS control button

Appendix- 103 -

English

In the Audio Control Panel, click the Audio I/O tab.Either click Dolby Digital 5.1 in the upper left listor click the Dolby Digital Live button at the centerbottom of the Audio Control Panel(Note).

In the Audio Control Panel, click the Audio I/O tab.In the upper left list, click Digital PCM Output.Enable this function to allow digital audio sourcesthat are not digitally processed by Dolby or DTSencoding to be output from the S/PDIF OUT.

Digital PCM Output Setup:

Introduction of Dolby Digital Live:

A real-time encoding technology, Dolby Digital Live converts anyaudio signal into a Dolby Digital bitstream for transport and playbackthrough a home theater system. With it, your PC or game console canbe hooked up to your Dolby Digital-equipped audio/video receiver or

digital speaker system via a single digital connection, eliminating the confusion of multiple cables andensuring the integrity of the audio signal.

(Note) When Dolby Digital Live is enabled, only digital auio output (S/PDIF) is working, and you willnot hear sound from analog speaker or headphone.


Engl

ish

4-1-6 Windows Vista ReadyBoost

Windows ReadyBoost allows you to use flash memory on a Windows Vista certified USB flash driveto boost your computer's performance. You may enable ReadyBoost and allocate part of your USBflash drive's memory to speed up your computer.

Follow the steps below to enable the ReadyBoost function:

Step 1:Go to Computer. Right-click on the USB flash drive icon and chooseProperties.

Step 2:In the ReadyBoost tab, select Use this device. Under Space toreserve for system speed, set the amount of memory space to usefor ReadyBoost using the slider or spin box. Click Apply and then OKto turn on ReadyBoost.

• The USB flash drive must have at least 256 MB of space.• The recommended amount of memory to use for ReadyBoost acceleration is one to three

times the amount of RAM installed in your computer.

Appendix- 105 -

English

4-2 TroubleshootingBelow is a collection of general asked questions. To check general asked questions based on a specificmotherboard model, please log on to GIGABYTE's website.

Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys afterentering BIOS menu and you will be able to see these options.

Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down andthat's why the light is still on.

Question 3: How do I clear CMOS?Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual. If yourboard doesn't have such jumper, you can take off the on-board battery to leak voltage to clear CMOS.Please refer to the steps below:

Steps:1. Turn off power.2. Disconnect the power cord from MB.3. Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object

to connect the positive and negative pins in the battery holder to makethem short for 5seconds).

4. Re-insert the battery to the battery holder.5. Connect power cord to MB again and turn on power.6. Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).7. Save changes and reboot the system.

Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, pleasechange another speaker with power/amplifier and try again later.

Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What dothese beeps usually stand for?Answer: The beep codes below may help you identify the possible computer problems. However, they areonly for reference purposes. The situations might differ from case to case.

AWARD BIOS Beep Codes1 short: System boots successfully2 short: CMOS setting error1 long 1 short: DRAM or M/B error1 long 2 short: Monitor or display card error1 long 3 short: Keyboard error1 long 9 short: BIOS ROM errorContinuous long beeps: DRAM errorContinuous short beeps: Power error


Engl

ish

Appendix- 107 -

English


Engl

ish

Appendix- 109 -

English


Engl

ish Contact Us

Taiwan (Headquarters)GIGA-BYTE TECHNOLOGY CO., LTD.Address: No.6, Bau Chiang Road, Hsin-Tien,Taipei 231, Taiwan TEL: +886-2-8912-4888 FAX: +886-2-8912-4003Tech. and Non-Tech. Support (Sales/Marketing) :http://ggts.gigabyte.com.twWEB address (English): http://www.gigabyte.com.twWEB address (Chinese): http://www.gigabyte.tw

U.S.A.G.B.T. INC.TEL: +1-626-854-9338FAX: +1-626-854-9339Tech. Support:http://rma.gigabyte-usa.comWeb address: http://www.gigabyte.us

MexicoG.B.T Inc (USA)Tel: +1-626-854-9338 x 215 (Soporte de habla hispano)FAX: +1-626-854-9339Correo: [email protected]. Support:http://rma.gigabyte-usa.comWeb address: http://www.gigabyte-latam.com

JapanNIPPON GIGA-BYTE CORPORATIONWEB address : http://www.gigabyte.co.jp

SingaporeGIGA-BYTE SINGAPORE PTE. LTD.WEB address : http://www.gigabyte.com.sg

ChinaNINGBO G.B.T. TECH. TRADING CO., LTD.WEB address : http://www.gigabyte.cnShanghaiTEL: +86-21-63410999FAX: +86-21-63410100BeijingTEL: +86-10-62102838FAX: +86-10-62102848WuhanTEL: +86-27-87851061FAX: +86-27-87851330GuangZhouTEL: +86-20-87540700FAX: +86-20-87544306 ext. 333ChengduTEL: +86-28-85236930FAX: +86-28-85256822 ext. 814XianTEL: +86-29-85531943FAX: +86-29-85539821ShenyangTEL: +86-24-83992901FAX: +86-24-83992909

IndiaGIGABYTE TECHNOLOGY (INDIA) LIMITEDWEB address : http://www.gigabyte.in

AustraliaGIGABYTE TECHNOLOGY PTY. LTD.WEB address : http://www.gigabyte.com.au

Appendix- 111 -

English

GermanyG.B.T. TECHNOLOGY TRADING GMBHWEB address : http://www.gigabyte.de

U.K.G.B.T. TECH. CO., LTD.WEB address : http://www.giga-byte.co.uk

The NetherlandsGIGA-BYTE TECHNOLOGY B.V.WEB address : http://www.giga-byte.nl

FranceGIGABYTE TECHNOLOGY FRANCEWEB address : http://www.gigabyte.fr

ItalyWEB address : http://www.giga-byte.it

SpainGIGA-BYTE SPAINWEB address : http://www.giga-byte.es

Czech RepublicRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in CZECH REPUBLICWEB address : http://www.gigabyte.cz

TurkeyRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in TURKEYWEB address : http://www.gigabyte.com.tr

To submit a technical or non-technical (Sales/Marketing) question, please link to :http://ggts.gigabyte.com.twThen select your language to enter the system.

RussiaMoscow Representative Office Of GIGA-BYTE TechnologyCo., Ltd.WEB address : http://www.gigabyte.ru

LatviaGIGA-BYTE LatviaWEB address : http://www.gigabyte.com.lv

PolandOffice of GIGA-BYTE TECHNOLOGY Co., Ltd. in POLANDWEB address : http://www.gigabyte.pl

UkraineWEB address : http://www.gigabyte.kiev.ua

RomaniaRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in RomaniaWEB address : http://www.gigabyte.com.ro

Serbia & MontenegroRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in SERBIA & MONTENEGROWEB address : http://www.gigabyte.co.yu

GIGABYTE Global Service System

- 112 -

motherboard manual ga-n680sli-dq6 2

Documents