module 6 (3.1) handling io devices

8/2/2019 Module 6 (3.1) Handling IO Devices

1/8

KEMENTERIAN PELAJARAN MALAYSIAKEMENTERIAN PELAJARAN MALAYSIA

Self Access LearningSelf Access LearningModuleModule

Computer HardwareComputer HardwareBasic MaintenanceBasic Maintenance

Handling Input and Output Devices

PUSAT PERKEMBANGAN KURIKULUMKEMENTERIAN PELAJARAN MALAYSIA

ICT Literacy forICT Literacy forSecondary SchoolSecondary School

ProgrammeProgramme


2/8

ICTL For Secondary School - HARDWARE Module

MODULE 6

BASIC MAINTENANCE -

HANDLING INPUT AND OUTPUT DEVICES

Curriculum Development CentreMinistry of Education Malaysia

1

ComputerComputer


3/8


1. Name of Module : Basic Maintenance Handling Input and Output Devices

2. Learning Outcomes: The students should be able to:

a. set up the input and output devices correctly

b. state the steps to connect the peripherals to system unit

c. powering the system

3. Knowledge and Skills

a. Set up the input and output devices correctly.

b. Connect the peripherals.

c. Power the system.

4. Module Summary: At the end of this module, students should be able to connect

peripherals and power the system such as monitor, keyboard, mouse and speaker to the

system unit.

This module contains 5 activities:

Activity 1: Name the peripheral port on the system unit

Activity 2: Connect the Monitor to system unit

Activity 3: Connect the Keyboard and mouse to system unit

Activity 4: Connect the Speaker to system unit

Activity 5: Powering the System

2


4/8


A ctivity 1: Name the Connecting Peripherals

Figure 1: Back view of the System Unit (ports)

3

No: Label the ports

1

2

3

4

5

6

7

8

9,10,11

Power port

PS2 port (Mouse)

PS2 port(keyboard)

USB port

Serial port (Modem)

Parallel port (printerport)

VGA port (Monitordisplay)

Game port(Joystick)

Audio ports

(speaker,headphone andmicrophone)

( 9-Line Out, 10-Line In, 11-Mic)


5/8


Activity 2: Connecting Monitor to system unit

1. Plug the VGA cable of the monitor to the display device port as shown in figure 2. The VGAcable (blue colour) must be connected to the display port of the same colour.

2. Connect the tiny pin on the VGA cable carefully.

Figure 2: Connecting VGA cable to monitor port

4

VGA cable

VGA cable

VGA ort

Monitor port


6/8


Activity 3 : Connecting the Keyboard and mouse to the System Unit

1. Plug the PS/2 cable of the keyboard (purple colour nozzle) and mouse ( green colournozzle) to the device port as shown in figure 3.1.

2. Attach the keyboard and mouse to their respective PS/2 port carefully.

Figure 3.1 : Connecting PS/2 keyboard and mouse to the respective ports

For keyboard and mouse that have USB toggle use figure 3.2

Figure 3.2 : Connecting USB toggle keyboard and mouse to the respective ports

5

Mouse green nozzle

Ke board ur le nozzle


7/8


Activity 3: Connecting Audio and Microphone device to system unit

1. Plug the (green nozzle) speaker cable and the (blue nozzle) microphone cable to thedevice port as figure 4.

Figure 4 : Connecting the Audio and Microphone nozzle to the respective ports

6


8/8


Activity 5 : Powering the System

1. Plug in the power cord as shown in Figure 5.1.

Figure 5.1 Plug in the power cord

2. Then, switch the power supply to On position. If the power supply switch is at theback of the computer system, press On as shown in Figure 5.2 . If not, proceed toStep 3.

Figure 5.2 Power Supply On / Off Switch

3. Press the power button as shown in Figure 5.3.

Figure 5.3 Power button

4. If everything is connected correctly, all system fans should start spinning. Thereshould be a single beep. After 2-5 seconds, the computer will start to boot.

7

Switch ON

Press the Onbutton

module 6 (3.1) handling io devices

Documents