model fsd-151 ul class 1 airfoil blade - pottorff · c e rt if d r ang ss lp o performance ratings...
TRANSCRIPT
RatingsUL 555 Fire Resistance Rating: 11/2 hour (vertical and horizontal)
UL 555S Leakage Class: 1 [8 cfm/sq.ft. @ 4 in.wg.] [(0.04 m3/s/m2 @ 1.0 kPa)]
UL HNLJ.V-5: Ventilation Duct AssembliesMaximum Dynamic Closure Velocity**: 4,000 fpm (20.3 m/s)
Maximum UL555S Rated Pressure: 6 in.wg. (1.5 kPa)Maximum Temperature**: 350°F (177°C)
ListingsUL 555 and 555S listing: R11767CSFM listing: 3225-0368:115 and 3230-0368:116New York City MEA listing: 295-98-EMeets NFPA Standards: 90A, 92A, 92B and 101Meets Building Code Standards: IBC, NBC, NFPA, SBC and UBC
model FSD-15111/2 hour • UL class 1 — combination fire smoke damper
airfoil blade
Fire
Sm
oke
Dam
pers
FSD15
1(1
/2) J
une
2014
ApplicationThe FSD-151 combination fire smoke damper employs airfoil bladesfor point-of-origin control of fire and smoke in static and dynamicsmoke management systems. The FSD-151 is qualified to 4,000 ft/min(20.3 m/s) and 6 in.wg. (1.5 kPa) and may be installed in vertical walls orpartitions, or horizontally in floors or assemblies with fire resistanceratings up to 2 hours.
Standard ConstructionFrame: 5" ¥ 1" (127 ¥ 25) galvanized steel hat channel with interlocking
corner gusset. Equivalent to 13 gauge (2.4) channel frame. Lowprofile head and sill are used on sizes less than 13" (330) high.
Blades: 6" ¥ 14 gauge (152 ¥ 2.0) equivalent galvanized — steel airfoil.
Sleeve: 16" ¥ 20 gauge (406 ¥ 1.0) galvanized steel.Axles: 1/2" (13) diameter plated steel hex.Linkage: Concealed in frame.Bearings: Stainless steel oilite, sleeve-type.
Seals: Silicone blade edge seals integrally rolled andmechanically fastened to blades. Flexible metal jamb seals.
Actuator: 120 VAC, power-open, spring-close, external mount.Fire Closure Device: HS-10 (electric) PFV (pneumatic)Fire Closure Temperature: 165°F (75°C).Minimum Size: 8" ¥ 8" (203 ¥ 203)
Maximum Size: Single section: 32" ¥ 48" (813 ¥ 1219) Multiple section: 144" ¥ 96" (3658 ¥ 2438) Options
Installation: o Vertical Mount o Horizontal MountVelocity Rating: o 2000 fpm o 3000 fpm o 4000 fpmTemperature Rating: o 2500 F o 3500 F(2000 fpm only)
o Alternate actuator:o Internal mount (actuator in air-stream).o 24 VAC o 230 VAC o Pneumatic o 24V Modulating**
o Opposed bladeo Parallel blade
o Alternate power-close, spring-open position.**o Alternate Actuator: o Internal Mount (actuator in air-stream) o 24 VAC
o DRS-30 — Two temperature fire closure device.(Includes PI-50 switch package)
o PI-50 — Dual position indicator switch package.o Alternate factory installed sleeve:
Gauge: o 18 (1.3) o 16 (1.6) o 14 (2.0) o 10 (3.5)Length: o 20" (508) o 24" (610) o Other______o Side Plate o No Sleeve (Actuator must be internally mounted)
o Transitions : o Flanged o Round o Ovalo Duct connections: o 1" (25) S-clip
o DM25 o DM35 o S & Drive oWardo Retaining angle systems:
Gauge: o 20 (1.0) o 16 (1.6)Picture frame: o SSPF (single-side) o DSPF (2-sided)Individual angle sets: o SS (single-side) o DS (2-sided)
o Alternate fire closure temperature:o 212°F (100°C) o 250°F (121°C) o 350°F (177°C)
o Duct smoke detector factory mounted and wired:o D4120 (100-4,000 fpm [0.5-20.3 m/s])o 2151 (0-3,000 fpm [0-15.2 m/s])
o Duct access door factory mounted in common sleeve.o Remote control stations:o RCP-1 (single) o RCP-1K (single, key controlled)o RCP-1M (single, momentary switch)
o Generic mullion for oversized masonry or concrete wall openings.
2"(51)
Std.
W*
H*
D
2"(51)
Std.
Type R (optional)Round duct transitions arestandard with D=W=H.(available with D<W and H)
Type O (optional)Oval duct transitions arestandard with W and H equalto damper width and heightdimensions. (available with Wand H smaller than damperwidth and height)
Model FSD-151(standard)
L I S T I N G
S
E R V I C E
ST
ATE OF CALIFORNIA
STATE FIR E M ARSHALL
POTTORFF® 5101 Blue Mound Road, Fort Worth, Texas 76106 www.pottorff.com
Information is subject to change without notice or obligation. NOTE: Dimensions in parentheses ( ) are millimeters.
Air PerformancePottorff certifies that the model FD-151 shownherein is licensed to bear the AMCA seal. Theratings shown are based on tests and proceduresperformed in accordance with AMCA publication 511and comply with the requirements of the AMCACertified Ratings Program. The AMCA CertifiedRatings Seal applies to air performance ratings only.
*Damper dimensions furnishedapproximately 1/4" (6) undersize.(sleeve thickness not included)
**Special Sizing Power Close Option 24V Modulating Option
Maximum Single Section 32" x 36" (813 x 914) 32" x 24" (813 x 610)
Maximum Multiple Section N/A 128" x 48" or 144" x 24"(3521 x 1219 or 3658 x 610)
Maximum Dynamic ClosureVelocity 2000 fpm (10.2 m/s) 2000 fpm (10.2 m/s)
Maximum Temperature 212°F (100°C) 250°F (121°C)
Fire
Sm
oke
Dam
pers
FSD15
1(2
/2) J
une
2014
5D 6D 5D
Air PerformancePottorff certifies that the model FSD-151 shown herein is licensed to bearthe AMCA seal. The ratings shownare based on tests and proceduresperformed in accordance with AMCApublication 511 and comply with therequirements of the AMCA CertifiedRatings Program. The AMCACertified Ratings Seal applies to airperformance ratings only.
Pressure drop testing was performedin accordance with AMCA Standard500-D using the three configurationsshown. All data has been corrected torepresent air density of 0.075 lb/ft.Actual pressure drop in any ductedHVAC system is a combination ofmany elements. This information,along with analysis of other systeminfluences, should be used toestimate actual pressure losses for adamper installed in a given HVACsystem.
S
Actuator and Sleeve Dimensional DataThe drawings and corresponding table illustrate the position of the damper when mounted ina factory sleeve and the relative space required for a given actuator. The standard mountinglocations provide enough space for installation of retaining angles and duct connections.
Airflow Performance Data Pressure Loss vs. Velocity
Figure 5.3 — Ducted Inlet and Outlet Figure 5.2 — Ducted Inlet Figure 5.5 Plenum Mount
NOTE: 1. Sleeve length “L” = wall/floor thickness + 10" (254). Standard sleeve length “L” = 16" (406).2. Damper may be rotated 180° to position actuator area on the left side.3. The entire damper frame is not required to be installed within the wall, partition or floor.
However, the closed plane of the damper blades must be inside the wall, partition or floor.4. Dimensions for FSNF24 apply to FSAF24-SR and FSAF24-BAL.5. Dimensions for FSLF24 apply to FSAFB24.6. Dimensions for ML4115/ML8115 apply to MS4209/MS8209.7. For dimensions on actuators not shown above, contact factory.
Ducted Inlet and OutletAMCA Figure 5.3 Illustrates a fully ducteddamper. This configuration represents thelowest pressure drop of the three testconfigurations because entrance and exitlosses are minimized by straight duct runsupstream and downstream of the damper.
Ducted InletAMCA Figure 5.2 Illustrates a ducteddamper exhausting air into an open area.This configuration has a lower pressuredrop than Figure 5.5 because entrancelosses are minimized by a straight duct runupstream of the damper.
Plenum MountAMCA Figure 5.5 Illustrates a plenummounted damper. This configuration hasthe highest pressure drop because ofextremely high entrance and exit lossesdue to the sudden changes of area in thesystem.
POTTORFF® 5101 Blue Mound Road, Fort Worth, Texas 76106 www.pottorff.com
Information is subject to change without notice or obligation. NOTE: Dimensions in parentheses ( ) are millimeters.
Damper Height
Actuator ModelFSLF120FSLF24
5"4"1"0"0"0"0"0"0"0"0"0"
6"-7"8"-9"
10"-11"12"-13"
14"15"-16"
17"18" and 23"
19"-20" and 25"21"-22" and 24"
26"-27">27"
F
T
6" and 10"7" and 11"-12"
8", 13"-14" and 21"9", 15"-17" and 20"
18"-19"22"-23"and >24"
24"All
7"7"4"3"2"1"3"0"0"0"0"0"
9"8"6"5"4"3"5"0"0"0"0"0"
5"4"1"0"0"0"0"0"0"0"0"0"
8"8"5"4"3"2"4"0"0"0"0"0"
9"8"5"4"4"3"5"0"0"0"0"0"
13"12"9"8"8"7"9"3"2"0"1"0"
3"2"1"0"0"0"0"
3"2"1"0"1"0"0"
3"2"1"0"1"0"0"
3"2"1"0"0"0"0"
4"3"2"0"2"0"0"
3"2"1"0"1"0"0"
3"2"1"0"1"0"1"
4-1/2" 4-1/2" 4-1/2" 4-1/2" 4-1/2" 5" 7-1/4"4"
2-5/8"4"
2-5/8"4"
2-5/8"4"
2-5/8"4"
2-5/8"4"
2-5/8"4"
2-5/8"2"
3-3/8"2"
3-3/8"2"
3-3/8"2"
3-3/8"2"
3-3/8"2"
3-3/8"2"
3-3/8"
FSNF120FSNF24
GGD221GGD121
ML4115ML8115
MS4120MS8120 331-4826 331-2998
S
X
J
<8"≥8"<8"≥8"