model er-a460 model er-a470 - inland cash … manual code: 00zera460vpme electronic cash register...
TRANSCRIPT
PROGRAMMING MANUALCODE: 00ZERA460VPME
ELECTRONICCASH REGISTER
MODEL ER-A460MODEL ER-A470(For "V" version)SRV KEY : LKGIM7113RCZZPRINTER : DP-730
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . . . . . . . . . . . 14
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
The ER-A460/A470 has the Easy Programming function which allows the user to
program easily.
This function is not described in this manual.
Please refer to the ER-A460/A470 EASY PROGRAMMING INSTRUCTION MANUAL of
an accessory for the product.
CONTENTS
SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice.
ER-A460
ER-A470
CHAPTER 1. SERVICE (SRV) MODEThe SRV key is used for operating in the SRV mode.
1. SRV. reset (Program Loop Reset)
Used to return the machine back to its operational state after a lock-up has occurred.
Procedure
• Method 1
1) Turn off the AC switch.
2) Set the mode switch to (SRV′) position.
3) Turn on the AC switch.
4) Turn to (SRV) position from (SRV′) position.
• Method 2
1) Set the mode switch to PGM2 position.
2) Turn off the AC switch.
3) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn on the AC switch.
Note: When disassembling and reassembling always power upusing method 1 only. Method 2 will not reset the CKDC6.
Note: SRV programming job#926-B must be set to "4" to allow PGMprogram loop reset.
PRG. RESET ***
2. Master reset (All memory clear)
There are two possible methods to perform a master reset.
• MRS-1Used to clear all memory contents and return machine back to itsinitial settings. return keyboard back to default. for default keyboardlayout.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key, turn to (SRV) positionfrom (SRV′) position.
• MRS-2Used to clear all memory and keyboard contents.This reset returns all programming back to defaults. The keyboardmust be entered by hand.This reset is used if an application needs different keyboard layoutother than that supplied by a normal MRS-1.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn to (SRV) position from (SRV′) position.
5) Key position assignment:
* After the execution of MRS-2, only the RECEIPT FEED andJOURNAL FEED keys can remain effective on key assignment.Any key can be assigned on any key position on the main key-board.
[key setup procedure]
MASTER RESET ***
NOTES:* 1: When the 0 key is pressed, the key of the key number on
display is disabled.* 2: Push the key on the position to be assigned. With this, the key
of the key number on display is assigned to that key position.
Key number Key name Key number Key name
1 Numeric key "0" 9 Numeric key "8"
2 Numeric key "1" 10 Numeric key "9"
3 Numeric key "2" 11 Numeric key "00"
4 Numeric key "3" 13 Decimal point key
5 Numeric key "4" 14 CL key
6 Numeric key "5" 15 ⊗ key
7 Numeric key "6" 16 ST key
8 Numeric key "7" 17 TL key
3. Reading of the SRV mode program
List of program reports
JOB# Report name
900SRV-mode program full item report (not incl. keyboardlayout)
950Keyboard layout report (on keys other than dept. keysand direct PLU keys)
951Keyboard layout report (on dept. keys and direct PLUkeys)
970 SRV file programming report
MRS-2 executed Key position set Free key
Disable
Free key setupcomplete.
*2
*1
0
0
– 1 –
[JOB# 900]All parameters contained for the SRV mode as listed
Key operation.
900 → & → 3
STAMP Stamp
01/01/00 0:00 Date/Time
000000 #0001 Machine No./Consecutive No.
#900 Job code
901# 0102 902# 0000
Contents of the SRV-modeprogramming
903# 4000 904# 0000 905# 0100 906# 0001
The contents of the programmingare printed only on the journalindividual formats shown at left.(No header is printed.)
907# 0014 908# 0000 909# 0000 910# 0004 911# 0000 912# 1141 913# 0002 914# 0100 915# 1020 916# 1000 917# 0000 918# 0000 919# 0000 920# 0000 921# 0000 922# 0000 923# 0000 924# 0000 925# 0000 926# 0000 927# 0000 928# 0000 929# 0000 980# 0000 930# z1 0000 Z1 reset counter
933# z1 0000 Hourly Z1 reset counter
934# z1 0000 PLU Z1/Z2 reset counter
935# z1 0000 Cashier Z1/Z2 reset counter
937# z2 0000 Z2 reset counter
939# z2 0000 Daily net Z2 reset counter
942#G T 2 *00000000000.00 GT2
943# G T 3 *00000000000.00 GT3
944# 0000 PGM2 mode secret code
945# 0000 Assignment Of RS232 channel
946# 0000 Assignment Of RS232 channel
948# 00 Training cashier No.
949# training Training mode title
[JOB# 950]The Key layout report is printed in SRV mode
Key operation
950 → & → 3
STAMP Stamp
01/01/00 0:02 Date/Time
000000 #0004 Machine No./Consecutive No.
#950 Job code
001 0 key 015 Key No./Key label/Location No.
002 1 key 016 003 2 key 024 004 3 key 032 005 4 key 017 006 5 key 025 007 6 key 033 008 7 key 018 009 8 key 026 010 9 key 034 011 00 key 023 012 000key 031
Key operation
951 → & → 3
STAMP Stamp
01/01/00 0:02 Date/Time
000000 #0005 Machine No./Consecutive No.
#951 Job code
001 ü ü é 055 Key No./key label/Location No.
002 ü ü â 056 003 ü ü ä 057 004 ü ü à 058 005 ü ü å 059 006 ü ü ç 060 007 ü ü ê 061 008 ü ü ë 062 009 ü ü è 063 010 ü é ü 064 011 ü é é 065 012 ü é â 066 013 ü é ä 067 014 ü é à 068 015 ü é å 069 016 ü é ç 070 017 ü é ê 071 018 ü é ë 072
– 2 –
[JOB#970]Files on the memory are listed.
Key operation
970 → & → 3
STAMP Stamp
01/01/00 0:03 Date/Time
000000 #0007 Machine No./Consecutive No.
#970 Job code
*001* 00018 /00018 File table No./No. of records
*002* 00018 /00018 /No. of used records
*003* 00018 /00018 *005* 00018 /00018 *006* 00018 /00018 *007* 00200 /00020 *008* 00200 /00020 *009* 00200 /00020 *012* 00200 /00020 *014* 00005 /00000 *015* 00005 /00000 *016* 00069 /00069 *017* 00069 /00069 *018* 00069 /00069 *019* 00004 /00004 *020* 00004 /00004 *021* 00004 /00004 *022* 00045 004/00045 File table No./No. of records/No. of blocks/No. of used records
*023* 00045 004/00045 *024* 00045 004/00045 *025* 00045 /00045 *026* 00045 /00045 *027* 00045 /00045 *028* 00045 /00045*029* 00049 /00049 *030* 00049 /00049 *031* 00032 /00000 *032* 00032 /00000 *033* 00070 /00070
1dbf80 File memory start address
1dff68 Empty memory start address
1dffff Memory end address
[JOB#990]Reading the Contents of the SRV-Mode Programming for SSP
Key operation
990 → & → 3
STAMP Stamp
01/01/00 0:03 Date/Time
000000 #0006 Machine No./Consecutive No.
#990 Job code
ssp era460v - 001 001 001 SSP No.
002 001 003 001 004 001 005 001 006 001 007 001
check sum error
– 3 –
4. Service mode programming
The following are the key operation required for programming.
Details of [A][B][C][D] will be discussed at each item description. mark is MRS setting.
[JOB #901]:MRS=0102#901-A: Not used (Fixed at "0")
#901-B: Tax system
1. TAX system 901-B
Auto TAX 1~3 0
Auto VAT 1~3 1
Manual VAT 1~3 2
Manual VAT 1 3
Manual TAX 1~3 4
Swiss TAX 5
#901-C: 1. Rounding system
1. Rounding system 901-C
Normal 0
SWEDEN 1
DENMARK 4
#901-D: 1. TAB setting
1. TAB setting 901-D
0. 0
0.0 1
0.00 2
0.000 3
[JOB#902] NOT USED MRS=0000
[JOB#903] MRS=4000#903-A: 1. IR communication baud rate
1. Baud rate (bps) 903-A
2400 2
4800 3
9600 4
19200 5
38400 6
57600 7
115200 8
* The communication speed with the ER-02FD is 19200bps.
#903-B, C, D: Not used (Fixed at "000")
[JOB#904] MRS=0000#904-A: 1. Printing of date
1. Printing of date 904-AYes 0
No 4
#904-B: 1. Printing of consecutive No.
1. Printing of consecutive No. 904-BYes 0
No 4
#904-C, D: Not used (Fixed at "00")
[JOB#905] MRS=0100#905-A: Not used (Fixed at "0")
#905-B: 1. Tax printing when taxable subtotal is zero.2. Tax printing when tax is zero.
1. Taxable subtotal iszero
2. Tax is zero905-B
SkipPrint 0
Skip 1
PrintPrint 4
Skip 5
#905-C: 1. Printing of rounding amount in receipt. (For Australia)2. Printing format for split pricing entry.
1. Printing of roundingamount in receipt
2. Printing format for splitpricing entry
905-C
NoNormal format 0
Australia format 1
YesNormal format 2
Australia format 3
#905-D : Not used (Fixed at "0")
[JOB#906] MRS=0001#906-A: 1. Print Dept. and PLU number on receipt.
2. Entry which makes the PLU stock counter negative
1. Print Dept. and PLUnumber on receipt.
2. Entry which makesthe PLU stockcounter negative
906-A
No
Allowed unconditionally 0
Operation alloweddespite ERROR
message1
Inhibited 2
Yes
Allowed unconditionally 4
Operation alloweddespite ERROR
message5
Inhibited 6
XXX TL
(Job#)
[A] [B] [C] [D]
Numeric entry4 digits max
0
– 4 –
#906-B: 1. Bottle return function2. Hash department setting
1. Bottle return function 2. Hash departmentsetting
906-B
DisableDisable 0
Enable 2
EnableDisable 4
Enable 6
#906-C: 1. Split pricing counting2. Multiplication entry
1. Split pricing counting 2. Multiplication entry 906-C
Quantity
Multiplication 0
Successivemultiplication
1
Split pricing 2
Package
Multiplication 4
Successivemultiplication
5
Split pricing 6
#906-D: 1. Presetting consecutive No.2. Fractional quantity
1. Presettingconsecutive No.
2. Fractional quantity906-D
YesNo 0
Yes (3 digit decimalplace)
1
NoNo 2
Yes (3 digit decimalplace)
3
[JOB#907] MRS=0014#907-A, B: Not used (Fixed at "00")#907-C: 1. In case of all cashier CCD and individual cashier CCD,
X1 report before CCD entry2. Locking of REG mode entry after individual cashier re-
setting3. Minus department and PLU
1. In case ofall cashierCCD andindividualcashierCCD, X1reportbefore CCDentry
2. Locking ofREG modeentry afterindividualcashierresetting
3. Minusdepartmentand PLU
907-C
DisableNo
Disable 0
Enable 1
YesDisable 2
Enable 3
EnableNo
Disable 4
Enable 5
YesDisable 6
Enable 7
#907-D: 1. Z-counter print for PLU, Hourly, Cashier, Daily net2. CCD compulsory
1. Z-counter print 2. CCD compulsory 907-D
YesNon compulsory 0
For individual cashier 1
For all cashier 2
NoNon compulsory 4
For individual cashier 5
For all cashier 6
[JOB#908] MRS=0000#908-A: GT print on Z report
GT1 (NET) GT2 (+) GT3 (–) 908-A
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#908-B: GT print on X report
GT1 (NET) GT2 (+) GT3 (–) 908-B
SkipSkip
Skip 0
Print 1
PrintSkip 2
Print 3
PrintSkip
Skip 4
Print 5
PrintSkip 6
Print 7
#908-C: 1. Add void-mode transaction data to hourly total report2. X1/Z1 report in X2/Z2 mode3. Resetting of consecutive number in Z1 resetting
1. Addvoid-modetransactionto hourlytotal report
2. X1/Z1 reportin X2/Z2mode
3. Resetting ofconsecutiveNo.in Z1resetting
908-C
NoEnable
No 0
Yes 1
DisableNo 2
Yes 3
YesEnable
No 4
Yes 5
DisableNo 6
Yes 7
#908-D:1. Printing X/Z report Journal only/Receipt & Journal (Except the
individual cashier report)2. Z1 resetting, resets GT Enable/Disable
1. Printing X/Z report 2. GT resetting at Z1 908-D
Receipt & JournalDisable 0
Enable 1
JournalDisable 4
Enable 5
– 5 –
[JOB#909] MRS=0000#909-A: 1. Printing of training GT on the X report
2. Printing of training GT on the Z report
1. Printing of trainingGT on the X report
2. Printing of trainingGT on the Z report
909-A
SkipPrint 0
Skip 1
PrintPrint 2
Skip 3
#909-B: 1. Printing of data on PLU resetting report2. All Z1 resetting in X1/Z1 mode
1. Printing of data onPLU resetting report
2. All Z1 resetting inX1/Z1 mode
909-B
PrintEnable 0
Disable 2
SkipEnable 4
Disable 6
#909-C: 1. Printing of data in void-mode totalizer and manager voidtotalizer on Z2 report
2. Printing of data in void-mode totalizer and manager voidtotalizer on Z1 report
1. Void-mode totalizeron Z2 printing
2. Void-mode totalizeron Z1 printing
909-C
PrintPrint 0
Skip 2
SkipPrint 4
Skip 6
#909-D: Not used (Fixed at "0")
[JOB#910] MRS=0004#910-A: 1. Over laped cashier function
2. Over laped cashier function 910-A
No 0
Yes 1
#910-B: 1. Auto cashier sign off at the end of each transaction
1. Auto cashier sign off at the end ofeach transaction
910-B
No (After cashier Z1 only) 0
Yes (Everytime) 1
#910-C: Not used (Fixed at "0")
#910-D: 1. Cashier system
1. Cashier system 910-D
1 hole 1
Cashier code entry 4
[JOB#911] MRS=0000#911-A: 1. Fraction treatment
1. Fraction treatment 911-ARound off 0
Round up 1Round down 2
#911-B, C, D: Not used (Fixed at "000")
[JOB#912] MRS=1141#912-A: 1. Date print format
Date format 912-AMonth/Day/Year 0Day/Month/Year 1
Year/Month/Day 2
#912-B: 1. Time system
1. Time system 912-B12H 024H 1
#912-C: 1. After transaction receipt format2. Copy receipt3. Footer print control
1. Aftertransactionreceipt
2. Copyreceipt
3. Footer printcontrol 912-C
Total only
No
All receipt 0On selected functionkeys at the time offinalization
1
Yes
All receipt 2On selected functionkeys at the time offinalization
3
Detail
No
All receipt 4
On selected functionkeys at the time offinalization
5
Yes
All receipt 6On selected functionkeys at the time offinalization
7
#912-D: 1. Logo message control
1. Logo/stamp message control 912-D3-line header instead of a stamp 0Stamp only 1
Stamp and 3-line footer 26-line header instead of a stamp 33-line header + 3-line footer 5
(Logo/stamp message format)
Header
Footer
Type : 0 532
STAMPSTAMP
1
– 6 –
[JOB#913] MRS = 0002#913-A: 1. VP format on Receipt/Journal
2. Content of TOTAL VP amount
1. VP format 2. VP amount 913-A
Date & amountTotal amount 0
Tendered amount 1
Machine# & amountTotal amount 2Tendered amount 3
#913-B: 1. Printing of [ST]2. Escape the compulsion of VP
NOTE: Must turn to MGR mode and depress
• • , PRINT keys to escape validation
1. ST Print 3. Escape the compulsion of VP 913-B
NoDisable 0
Enable 1
YesDisable 4
Enable 5
#913-C: 1. Buzzer off 2sec. after lock error.2. Buffered keyboard
1. Error beep 2. Buffered keyboard 913-C
2-sec. offYes 0
No 1
ConstantYes 2
No 3
#913-D: 1. Drawer closing compulsory2. Error mode3. Key catch sound
1. Drawerclosingcompulsory
2. Error mode 3. Key catchsound 913-D
Non-compulsoryAll lock error
Enable 0
Disable 1
Miss operation(One shot error)
Enable 2
Disable 3
CompulsoryAll lock error
Enable 4
Disable 5
Miss operation(One shot error)
Enable 6
Disable 7
[JOB#914] MRS = 0100#914-A: 1. Receipt issuing at no-sale
2. [NS] key separation from [TL] key for no sale function
1. Receipt issuing atno-sale
2. [NS] key separation914-A
EnableYes 0
No 2
DisableYes 4
No 6
#914-B: 1. No-sale after NON ADD code entry
1. No-sale after # entry 914-B
Disable 0
Enable 1
#914-C 1. Action to be taken when the machine is locked by theReceipt/Journal paper near end check
2. Void mode
1. Action to betaken when themachine islocked by theReceipt/Journalpaper near endcheck
2. Void mode
914-C
Unlocked by CLkey
Enable 0
Disable 2
Enforcing of paperroll replacement
Enable 4
Disable 6
#914-D: 1. CHECK CASHING Enable/Disable
1. CHECK CASHING 914-D
Disable 0
Enable 2
[JOB#915] MRS = 1020#915-A: 1. Amount symbol
1. Amount symbol 915-A" $ " 0" * " 1
" " 2
#915-B: Not used (Fixed at "0")
#915-C: 1. Paper near end check2. ST (–), ST (%) as many times needed/operation only
once
1. Paper near endcheck
1. ST (–), ST (%)as many timesneeded/operation onlyonce
915-C
YesUnlimited 0
Once only 2
NoUnlimited 4
Once only 6
#915-D: Not used (Fixed at "0")
– 7 –
[JOB#916] MRS = 1000#916-A: 1. Print format when text and amount overlaps each other
REG mode
1. Print format when text and amountoverlaps each other REG mode
916-A
Truncate text 0
2 line print 1
#916-B: 1. Finalization by charge (credit) when ST t 0
1. Finalization by (credit) when SBTL t 0 916-B
Disable 0
Enable 4
#916-C: 1. Negative merchandise subtotal2. Subtotal entry compulsory before tendering3. Subtotal entry before direct non-tendering finalization
1. Negativemerchan-disesubtotal
2. Subtotalentrycompulsorybeforetendering
3 .Subtotalentry beforedirectnon-tenderingfinalization
916-C
AllowNoncompulsory
Non-compulsory 0
Compulsory 1
CompulsoryNon-compulsory 2
Compulsory 3
DisallowNon-compulsory
Non-compulsory 4
Compulsory 5
CompulsoryNon-compulsory 6
Compulsory 7
#916-D: 1. Coupon PLU printing on X/Z report2. Net sales subtotal (NET1) printing on X/Z report3. CHECK change total printing on X/Z report
1. Print couponPLU’s ongeneral report
2. Print netsales SBTL(NET1) ongeneral report
3. Print CHKCHANGE ongeneral report
916-D
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
[JOB#917] NOT USED: MRS = 0000
[JOB#918] MRS = 0000#918-A: 1. Printing of text of a tied PLU in set PLU
2. Dirrect non-tendering finalization after previous tenderentry
1. Printing of text of a tiedPLU in promo PLU
2. Dirrect non-tenderingfinalization afterprevious tender entry
918-A
YesDisable 0
Enable 2
NoDisable 4
Enable 6
#918-B: Not used (Fixed at "0")#918-C: 1. Printing Z1/Z2 counter in Z reports
1. Printing Z1/Z2 counter in Z reports 918-C
Print 0
Skip 4
#918-D: Not used (Fixed at "0")
[JOB#919] MRS = 0000#919-A, B: Not used (Fixed at "00")
#919-C: 1. Amount printing when PLU unit price is 0
1. Amount printing when PLU unit price is 0 919-C
No 0
Yes 1
919-D: 1. Conversion ST printing of native ST
1. Conversion SBTL print of native SBTL 919-D
Yes 0
No 4
[JOB#920] NOT USED MSR = 0000
[JOB#921] NOT USED MRS = 0000
[JOB#922] NOT USED MRS = 0000
[JOB#923] NOT USED MRS = 0000
[JOB#924] NOT USED MRS = 0000
[JOB#925] NOT USED MRS = 0000
[JOB#926] MRS = 0000#926-A: Not used (Fixed at "0")
#926-B: 1. Program reset at PGM 2 mode
1. Program reset at PGM2 mode 926-B
Disable 0
Enable 4
#926-C, D: Not used (Fixed at "00")
– 8 –
[JOB#927] MRS = 0000#927-A: 1. Rounding up of the units digit of amount
#927-B: 1. Rounding down of the units digit of amount
1. Rounding the units digit of amount 927-AB
Common destination 00
Netherland/Switzerland 82
Norway 54
#927-C: 1. Difference memory (Difference between before-rounding and after-rounding)
2. Limit on the least sighificant digit in entering the amounton item
1. Difference memory 2. Limit on the leastsighificant digit inentering the amounton item
927-C
NoArbitary 0
0 only 1
0 and 5 only 2
YesArbitary 4
0 only 5
0 and 5 only 6
#927-D: 1. Application of rounding2. Limit on the least significant digit in entering the amount
of payment
1. Application of rounding 2. Limit on the leastsignificant digit inentering the amountof payment
927-D
Item & PaymentArbitary 0
0 only 10 and 5 only 2
PaymentArbitary 40 only 5
0 and 5 only 6
[JOB#928] NOT USED: MRS = 0000
[JOB#929] NOT USED: MRS = 0000
[JOB#980] MRS = 0000#918-A, B, C: Not used (Fixed at "000")#980-D: 1. Language selection of guidance message
1. Language selection of guidancemessage
910-D
English 0
German 1
[JOB#930 ∼939] MRS = 0000RESET REPORT COUNTER
JOB # Function
930 Z1 report counter
933 Hourly Z1 report counter
934 PLU Z1/Z2 report counter
935 Cashier Z1/Z2 report counter
937 Z2 report counter
939 31 day daily net Z2 report counter
[JOB#942, 943] MRS = 0000000000000GT COUNTER PRESETTING
JOB # Function942 GT2 (Positive GT)943 GT3 (Negative GT)
Note: GT1 is obtained by calculationEquation: GT1=GT2-GT3
[JOB#944] MRS = 0000PGM1/2 secret code presetting
NOTE: When the secret code "0" is programmed, the secret codeentry is be inhibited.
[JOB#945] MRS = 0000The assignment of RS232 channel by each devices
* For use, the option control ROM (ER-A46R1) and the RS232 I/F(ER-A5RS) are required.
#945-A: 1. Channel No. for online
1. Channel No. for online 945-A
Channel No. 0 to 7
#945-B, C, D: Not used (Fixed at "000")
* 0 = No connect1 to 7 = Channel number
[JOB#946] NOT USED: MRS = 0000
[JOB#948] MRS = 000000PROGRAMMING OF TRAINING CASHIER NO.
[JOB#949] MRS = "TRAINING"THE TRAINING MODE’S TITLE
Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.
[JOB#989]RESETTING OF ALL COUNTER AND TOTALIZER
Job# ABCD
Initial value of Z countr
"0000"
TL
Job# 000000000000013 digits
0
TL
944 XXXX4 digits
0
TL
Job# ABCD
0
TL
948 XX TL
XX: Cashier No.
949 Character Key(8chra.)
Space
TL
989 TL
– 9 –
[JOB#950] MRS = STANDARD KEY LAYOUTFree key layout (Except for department keys and direct PLU keys.)
[JOB#951] MRS = STANDARD KEY LAYOUTFree key layout (department keys and direct PLU keys)
• Programming of the keys to be dept keys or direct PLU keys onthe keyboard.
• Key No. is assigned to each key which is supposed to be dept.Key or direct PLU key by depressing the key after entering the keyNo.
• Those keys programmed by this job No. will be dept. keys if dept.code is assigned, and will be direct PLU keys if PLU code isassigned in the PGM2 mode.
FUNCTION KEY LIST
Key No. KEY KEY TEXT
1 0 KEY 0 KEY
2 1 KEY 1 KEY
3 2 KEY 2 KEY
4 3 KEY 3 KEY
5 4 KEY 4 KEY
6 5 KEY 5 KEY
7 6 KEY 6 KEY
8 7 KEY 7 KEY
9 8 KEY 8 KEY
10 9 KEY 9 KEY
11 00 KEY 00 KEY
12 000 KEY 000KEY
13 DECIMAL POINT . KEY
14 CLEAR CLEAR
15 ⊗
16 ST SBTL
17 TL TOTAL
18 # #
19 NO SALE NS
20 PLU PLU
21 G. C. COPY GCCOPY
22 Level1 L1
23 Level2 L2
24 Level3 L3
25 PRINT VP
26 RCPT RCPT
27 VOID VOID
28 REFUND RFND
Key No. KEY KEY TEXT
29 %1 %1
30 %2 %2
31 %3 %3
32 %4 %4
33 (–)1 (–)1
34 (–)2 (–)2
35 (–)3 (–)3
36 (–)4 (–)4
37 VAT VAT
38 AUTO AUTO
39 AUTO2 AUTO2
40 AUTO3 AUTO3
41 AUTO4 AUTO4
42 AUTO5 AUTO5
43 CASH2 CA2
44 CHECK1 CHECK1
45 CHECK2 CHECK2
46 CHECK3 CHECK3
47 CHECK4 CHECK4
48 CR1 CR1
49 CR2 CR2
50 CR3 CR3
51 CR4 CR4
52 CONV1 EX1
53 CONV2 EX2
54 CONV3 EX3
55 CONV4 EX4
59 RA RA
60 RA2 RA2
61 PO PO
62 PO2 PO2
63 1⁄2 1⁄2 KEY
64 AMT AMT
65 VAT SHIFT VAT SF
66 CASHIER NO. CASH#
67 DIFFER ST DIF ST
ER-A460 KEY POSITION
R J 16 22 28 34 40 46 52 58 64 70 76 825 10 15 21 27 33 39 45 51 57 63 69 75 814 9 14 20 26 32 38 44 50 56 62 68 74 803 8 13 19 25 31 37 43 49 55 61 67 73 792 7 12 18 24 30 36 42 48 54 60 66 72 781 6 11 17 23 29 35 41 47 53 59 65 71 77
ER-A470 KEY POSITION
R J 22 30 38 46 54 62 70 78 86 94 102 110 1187 14 21 29 37 45 53 61 69 77 85 93 101 109 1176 13 20 28 36 44 52 60 68 76 84 92 100 108 1165 12 19 27 35 43 51 59 67 75 83 91 99 107 1154 11 18 26 34 42 50 58 66 74 82 90 98 106 1143 10 17 25 33 41 49 57 65 73 81 89 97 105 1132 9 16 24 32 40 48 56 64 72 80 88 96 104 1121 8 15 23 31 39 47 55 63 71 79 87 95 103 111
950 Free key
Key number automaticincrement
Key number manualincrement
Initial setting
XXXKey No.
To inhibit
TL
951 Free keyXXXKey No.
Key number automaticincrement
Key number manual increment
To inhibit
TL
– 10 –
[JOB#971]SRV FILE PROGRAMMING. (File creation deletion and change ofrecord count or block count)
Key operation
• Normal file
GroupNo.
File name Type* File table No.(Create/Erase)
1Dept.
101, 02, 03, 05,37, 40, 42
2 Dept Text (8chra.) 0 03
3 Dept Text (12chra.) 0 04
4 PLU 1 07, 08, 09, 12
5 PLU Text (8chra.) 0 09
6 PLU Text (12chra.) 0 10
7 PLU stock 0 11
8 Link PLU 1 14
9 Set PLU 1 15
10Cashier
119, 20, 21, 22,23, 24, 34, 37,38, 39
11Cashier Dept
037, 38, 40, 41,42, 43
12 Hourly 1 29, 30
13 Daily net 1 31, 32
14 Reg. buffer 1 33, 34
15 Overlapped cashier 0 34
16 Message Text 0 35
17 Guidance Text 0 36
18 Term Dept. 0 06
19 Term PLU 0 13
20 Term Transaction 0 18
21 Term Cashier 0 24
22 Term Cashier Dept 0 39
23 All of term file 0 06, 13, 18, 24, 39
Type = 0 ; Create/Erase onlyType = 1 ; Create/Erase and Increase/decrease the number of
Records or blocks. * : The files which are created or erased by the entry of group
No.
971 @/FOR abcFile group No.
delete
XXXXXNumber of records
TL
– 11 –
File table
TableNo.
File nameRECORD BLOCK Label
sizeDatasizeMRS Max. #1 MRS Max. #2
1 Dept. Preset 18 50 1 1 1 6
2 Price 18 50 (1) 1 1 0 3
3 Text (8chra.) 18 50 (1) 1 1 0 8
4 Text (12chara.) 0 50 (1) 0 1 0 12
5 Daily 18 50 (1) 1 1 0 9
6 Term 18 50 (1) 1 1 0 9
7 PLU Preset 200 *** 1 1 3 6
8 Price 200 *** (7) 1 1 0 3
9 Text (8chra.) 200 *** (7) 1 1 0 8
10 Text (12chra.) 0 *** (7) 0 1 0 12
11 Stock 0 *** (7) 0 1 0 4
12 Daily 200 *** (7) 1 1 0 9
13 Term 0 *** (7) 0 1 0 9
14 Link PLU 5 *** 1 1 3 15
15 Set PLU 5 *** 1 1 3 30
16 Transaction Label 69 69 1 1 2 0
17 Daily 69 69 (16) 1 1 0 8
18 Term 69 69 (16) 1 1 0 8
19 Cashier Preset 4 15 1 1 1 3
20 Flag 4 15 (19) 1 1 0 2
21 Text 4 15 (19) 1 1 0 8
22 Cashier transaction Label 45 45 4 15 (19) 2 0
23 Daily 45 45 (22) 4 15 (19) 0 8
24 Term 45 45 (22) 4 15 (19) 0 8
25 Reset Csr trns. Label 45 45 1 1 2 0
26 Daily 45 45 (25) 1 1 0 8
27 Total cashier (Buffer) Label 45 45 1 1 2 0
28 Total 45 45 (27) 1 1 0 8
29 Hourly Label 49 49 1 1 1 0
30 Daily 49 49 (29) 1 1 0 8
31 Daily net Label 32 32 1 1 3 0
32 Total 32 32 (30) 1 1 0 8
33 Reg. buffer 70 255 1 1 0 36
34 Over lapped Csr 0 255 0 15 (19) 0 36
35 Message Text 0 87 0 1 2 12
36 Guidance Text 0 132 0 1 2 12
37 Csr trns. Dept Label 0 50 0 15 (19) 1 0
38 Daily 0 50 (37) 0 15 (19) 0 9
39 Term 0 50 (37) 0 15 (19) 0 9
40 Reset Csr Dept trns. Label 0 50 0 1 1 0
41 Daily 0 50 (40) 0 1 0 9
42 Total Csr (Buffer) Dept Label 0 50 0 1 1 0
43 Total 0 50 (41) 0 1 0 9
(#1) : Same as the number of record of table no. N(#2) : Same as the number of block of table no. N
– 12 –
[JOB#996, 998] IR data send/receive (ECR↔ECR, ECR↔ER-02FD)
[JOB#996] IR data send
X : SSP = 0
• Send to ECR (IrDA) : IrDA(Enable baud-rate : 115200bps,
57600bps, 38400bps,19200bps, 9600bps,4800bps, 2400bps)
• Send to ER-02FD + CE-IR2 (CE-IR4) : ASK(Enable baud-rate : 19200bps)
• Send to ECR (ASK) : ASK(Enable baud-rate : 57600bps, 38400bps,
19200bps, 9600bps,4800bps, 2400bps)
[JOB#998] IR data receive
• Receive from ECR (IrDA) : IrDA(Enable baud-rate : 11500bps, 57600bps,
38400bps, 19200bps,9600bps, 4800bps,2400bps)
• Receive from ER-02FD + CE-IR2 (CE-IR4) : ASK(Enable baud-rate : 19200bps)
• Receive from ECR (ASK) : ASK(Enable baud-rate : 57600bps, 38400bps,
19200bps, 9600bps,4800bps, 2400bps)
996
All data
X
Send to ECR(IrDA)
Send to ER-02FD or ECR(ASK)
ST
TL
998
Receive from ECR(IrDA)
Receive from ER-02FD or ECR(ASK)
ST
TL
– 13 –
CHAPTER 2. PROGRAM(PGM2/PGM1) MODE
1.Reading of the PGM mode program
[JOB#1100]: DEPT readingKey operation
STAMP Stamp
01/01/00 0:04 000000 #0009
#1100 *P G M â * Job Code/Mode title
01-10 Start No. – End No.
D 01 0.00 Dept. code/Taxable/Sign, Price
dpt.ü é g01 Text/Group No.
0000001 col17 Program (* 1) Commission Group/HALO
D 02 0.00 dpt.ü â g01 0000001 col17 D 03 0.00 dpt.ü ä g01 0000001 col17 D 04 0.00 dpt.ü à g01 0000001 col17 D 05 0.00 dpt.ü å g01 0000001 col17 D 06 0.00 dpt.ü ç g01 0000001 col17 D 07 0.00 dpt.ü ê g01 0000001 col17 D 08 0.00 dpt.ü ë g01 0000001 col17 D 09 0.00 dpt.ü è g01
(* 1) PROGRAM: ABCDEFGA: Printing on the cashier report Yes/No 1/0B: Item vp compulsory/noncompulsory 1/0C: (Not used) 0D: (Not used) 0E: SIF/SICS/Normal 2/1/0F: (Not used) 0G: Amount entry type
Open and preset/preset/open/inhibited 3/2/1/0
[JOB#1200]: PLU readingKey operation
STAMP Stamp
01/01/00 0:05 000000 #0011
#1200 *P G M â * Job Code/Mode title
000001-000005 Start No. – End No.
P 000001(ü é ) /00 PLU code (Dept code)/(* 1)/Base q’ty
0.00 Taxable/Sign, Price
pl000001 co Text/Commission Group
002 Program (* 2)/Stock
P 000002(ü é ) /00 0.00 pl000002 co 002 P 000003(ü é ) /00 0.00 pl000003 co 002 P 000004(ü é ) /00 0.00 pl000004 co 002
(* 1) NORMAL. LINK PLU. SET MENU: NORMAL: L LINK PLU: S SET MENU
(* 2) PROGRAM: ABCA: (Not used) 0B: (Not used) 0C: Amount entry type
Open and preset/preset/open /inhibited = 3/2/1/0 (PLU) (Sub-dept)
1100 XXStart No.
XXEnd No.
Single item
All
TL
1200 XXXXStart No. End No.
Single item
XXXX
All
TL
– 14 –
[JOB#1220]: STOCK ADD PRESET
STAMP Stamp
01/01/00 0:06 000000 #0005
#1220 *P G M â * Job Code/Mode title
P 000001 1000.000 Old stock
10.000 (Input stock)
s 1010.000 New stock
[JOB#1221]: STOCK SUB PRESET
STAMP Stamp
01/01/00 0:06 000000 #0005 #1221 *P G M é * Job code/Mode title
P 000001 1000.000 Old stock
-10.000 (Input stock)
s 990.000 New stock
[JOB#1222]: STOCK INVENTORY PRESET
STAMP Stamp
01/01/00 0:06 000000 #0005 #1222 *P G M é * Job code/Mode title
P 000001 1000.000 Old stock
500.000 (New stock) - (Old stock)
s 15000.000 New stock (Input stock)
[JOB#2220]: LINK PLU PRESET OR READINGKey operation
STAMP Stamp
01/01/00 0:06 000000 #0010
#2220 *P G M â * Job code/Mode title
000001-999999 Start No. – End No.
P 000002 L p000011 PLU code/Link PLU code (Max 5) p000012 /Link PLU code
[JOB#2221]: SET MENU PRESET OR READINGKey operation
STAMP Stamp
01/01/00 0:06 000000 #0011
#2221 *P G M â * Job code/Mode title
000001-999999 Start No. – End No.
P 000001 S p000002 PLU code/Set PLU code (Max. 10)
p000003 /Set PLU code
[JOB#1300]: FUNCTION PRESET READINGKey operation
2220Start No. End No.
Single item
XXXXXX XXXXXX
All
TL
2221Start No.
XXXXXX
All
End No.
Single item
XXXXXX TL
1300 TL
– 15 –
STAMP Stamp
01/01/00 0:06 000000 #0015
#1300 *P G M â * Job code/Mode title
F 001[ ~ ] é Function No./Text
S -0.00 Sign, Rate
l17 HALO
F 002[ ~ ] â S -0.00 l17 F 005 ‰ é S -0.00% Rate
l100.00% F 006 ‰ â S -0.00% Rate
l100.00% F 009 set plu- F 011 tax1 stF 012 tax2 stF 013 tax3 stF 015 vat 1F 016 vat 2F 017 vat 3F 019 N E T éF 020 N E T âF 021 cp pluF 022 refundF 023 \F 024 ¡ modeF 025 mgr ¿F 026 sbtl ¿F 029 vat sftF 030 tax deleF 031 vp cntF 032 no sale HALO
F 033 g.c. cntF 036 ***ra l18F 038 ***po l18F 041 C ash l18 00000000000 (* 1) PGM
F 043 check l18 00000000000 F 047 credit1 l18 00000000000F 048 credit2 l18 00000000000F 051 exch1 0.0000F 058 ****cid 9999999.99F 060 ca/ch id F 061 chk/cg 999999.99 F 062 guestF 063 com.sal1 0.00%F 064 com.sal2 0.00%F 065 com.sal3 0.00%
F 066 non com.F 067 order tlF 068 paid tlF 069 dom.cur1F 073 *ch idF 074 *dept tlF 075 dept(-)F 080 net 1F 081 net 2F 082 net 3F 084 subtotalF 085 mdse stF 086 ***totalF 087 changeF 088 dueF 089 itemsF 090 plu stF 091 C O P YF 092 g.c copyF 093 ave.F 094 G roup01 F 095 G r0up02F 096 G roup03F 097 G roup04F 098 G roup05F 099 G roup06F 100 G roup07F 101 G roup08F 102 G roup09F 106 O ~ PF 107 com.amt1F 108 com.amt2F 109 com.amt3F 110 ccm.ttlF 111 D E P TF 112 groupF 113 P L UF 114 stockF 115 trans.F 116 tl-idF 117 salesF 118 cashierF 119 hourlyF 120 dailyF 121 set pluF 122 ttl taxF 123 N E TF 124 zero salF 125 category
(* 1) PGM: ABCDEFGHIJKA: EFT function compulsory/noncompulsory 1/0B: Footer print Yes/No 1/0C: Non-add code entry compulsory/noncompulsory 1/0D: Change due Disable/Enable 1/0E: VP compulsory/noncompulsory 1/0F: (Not used) 0G: (Not used) 0H: (Not used) 0I: (Not used) 0J: Drawer opening No/Yes 1/0K: Entry of amount tenderd
compulsory/noncompulsory compulsory/inhibit
(Cash, check) 1/0(CR1 to 8) 1/0
– 16 –
[JOB#2600]: READING OF OTHERKey operation
STAMP Stamp
01/01/00 0:08 000000 #0017
#2600 *P G M â * Job code/Mode title
#2615 10 SLIP/VP
#2616 (* 1) Optional feature
01 00000000 02 00000000 03 00000000 04 00000000 05 00000000 06 00000000 07 00000000 08 00000000 09 00000000 10 00000000 11 00000000 12 00000000 13 00000000#2617 000 Till timer
#2619 0 00 (* 3) Hourly report
#2620 Stack report 1
#2630 0000 Secret code PGM1
#2631 0000 X1/Z1
#2632 0000 X2/Z2
(* 1) Optional feature: ABCDEFGH
MRS = 00000000
x: 1 MRS = 00000000A: OP X/Z report Disable/Enable 1/0B: PO operation in REG mode Disable/Enable 1/0C: (Not used) 0D: "RFND" key entry in REG mode Disable/Enable 1/0E: Direct void function in REG mode Disable/Enable 1/0F: Indirect void in REG mode Disable/Enable 1/0G: Subtotal void in REG mode Disable/Enable 1/0H: Refund VP Compulsory/Non compulsory 1/0
x: 2 MRS = 00000000A: The first last item void Disable/Enable 1/0B: PLU level shift system Manual/Auto 1/0C: PLU level shift system MGR/MGR & REG 1/0D: Printing of the number of purchases Yes/No 1/0E: Time print No/Yes 1/0F: Journal select/Full print 1/0G: Item VP Disable/Enable 1/0H: (–) VP Compulsory/Non compulsory 1/0
x: 3 MRS = 00000000A: (Not used) 0B: (Not used) 0C: Zero skip in Cashier report No/Yes 1/0D: Zero skip in Transaction report No/Yes 1/0E: Zero skip in DEPT. report No/Yes 1/0F: Zero skip in PLU report No/Yes 1/0G: Zero skip in hourly report No/Yes 1/0H: Zero skip in Daily net report No/Yes 1/0
x: 4 MRS = 00000000A: (Not used) 0B: (Not used) 0C: Vat/Tax amount printing on R/J No/Yes 1/0D: Taxable amount printing on R/J No/Yes 1/0E: Net amount printing on R/J No/Yes 1/0F: (Not used) 0G: (Not used) 0H: When PLU level system is "Auto" (x: 2 B = 0),
PLU level returns to level 1 by one receipt/by one item. 1/0
x: 5 MRS = 00000000A: (Not used) 0B: (Not used) 0C: (Not used) 0D: VAT shift system By shift key/by cashier 1/0E: (Not used) 0F: (Not used) 0G: (Not used) 0H: (Not used) 0
x: 6 (Not used) MRS = 00000000
x: 7 (Not used) MRS = 00000000
x: 8 (Not used) MRS = 00000000
x: 9 (Not used) MRS = 00000000
x: 10 (Not used) MRS = 00000000
x: 11 (Not used) MRS = 00000000
x: 12 (Not used) MRS = 00000000
x: 13 MRS = 00000000A: Credit totalizer update if RA/PO finalized
by Credit key Yes/No 1/0B: Separater line in report Separater line/1 line 1/0C: (Not used) 0D: (Not used) 0E: (Not used) 0F: (Not used) 0G: (Not used) 0H: (Not used) 0
(* 2) Hourly report : a bca: Hourly report format by 15 minutes/by 30 minutes 1/0bc: start hour 00 to 23
2600 TL
2616 X ABCDEFGH
0
ST TL
– 17 –
[JOB#2640]: READING OF TEXT PROGRAMMINGKey operation
STAMP Stamp
01/01/00 0:08 000000 #0019
#2640 *P G M â * Job code/Mode title
#2641 01 entry error Message text
02 misoperation 03 no record 04 paper empty 05 secret code 06 07 memory full 08 09 10 out of stock11 sbtl compul.12 tend compul.13 14 15 16 17 18 19 20 21 22 cashier err.23 entry err ca24 25 26 27 28 29 30 31 # compulsory32 not assigned33 not change34 over limit.35 inh. open pr36 inh. unit pr37 not non-tend38 39 p off in vp40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 buffer full68 69 70 71 72 eft error73 eft break74 75 76 close drawer77 78 79 80 81 entr secret#82 send83 receive84 send ok85 receive ok86 com. error87 data error88 time out89 cancel#2644 001 dept price Guidance
002 dept func. 003 dept taxable 004 dept halo 005 dept text 006 dept com.grp 007 dept group 008 dept drctkey009 plu asg.dept 010 plu price 011 plu base qty012 plu stck add013 plu stck sub014 plu stck ovw015 plu function016 plu taxable017 plu text018 plu com.grp019 plu drct key020 link plu
2640 TL
– 18 –
021 set plu022 plu code rng023 plu func rng024 plu stts rng025 plu com rng026 rate prgram027 misc key pgm028 fnc key halo029 mdiakey halo030 % halo031 func text032 misc key pgm033 misc key pgm034 mdia key pgm035 mdiakey halo036 csr code pgm037 csr name pgm038 csr pgm039 date program040 time program041 mchn no. pgm042 cc no. pgm043 logotext pgm044 vp count045 opt feature046 drawer alarm047 hourlyreport048 stack report049 secret(pgm1)050 secret(x1z1)051 secret(x2z2)052 messge text053 guid text054 tax rate055 price056 enter dept#057 sign (-)058 sign (+)059 taxable1:yes060 taxable1:no061 taxable2:yes062 taxable2:no063 taxable3:yes064 taxable3:no065 vat:yes066 vat:no067 prt csr:yes068 prt csr:no069 vp compl:yes070 vp compl:no071 sif072 sics073 normal074 delete075 open&prest076 preset077 open078 inhibited079 halo(exp.)080 halo(amount)081 halo(rate)082 com.grp083 group084 base q’ty
085 stock(add)086 stock(sub)087 stock(over)088 rate089 item090 st091 eft cmpl092 eft noncmpl093 footer :yes094 footer :no095 # cmpl096 # noncmpl097 due disable098 due enable099 drw open:yes100 drw open:no101 tnd cmpl:yes102 tnd cmpl:no103 tnd inh.104 enter plu#105 ent.csr code106 ent.csr no107 ent.drw#108 g.c copy yes109 g.c copy no110 vat sft stat111 vat sft not112 ent.dept#113 ent.key#114 ent.func#115 ent.pos.code116 enter tax no117 ent.tax rate118 lower tax119 enter msg no120 enter gid no121 (fixed data)122 entercoookey‘123 data send124 data rcv.125 org’zer rcv.126 onl t.no.127 onl modem128 onl baudrate129 onl code130 onl timer
– 19 –
[JOB#2900]: AUTO KEY READINGKey operation
STAMP Stamp
01/01/00 0:08 000000 #0005
#2900 *P G M â * Job code/Mode title
#üé 1 key 0 key 0 key total#üâ D ü é (DEPT01)
D ü â P 000001 (PLU000001)
:#üå 1 key 0 key 0 key total check
[JOB#1500]: CASHIER READING REP.Key operation
STAMP Stamp
01/01/00 0:08 000000 #0016
#1500 *P G M â * Job code/Mode title
01csr# 01 Cashier code/Name
0000d1 Drawer No.
02csr# 02 0000d1 03csr# 03 0000d1 04csr# 04 0000d1
[JOB#2700]: TAX TABLE READING REP.Key operation
STAMP Stamp
01/01/00 0:08 000000 #0005
#2700 *P G M â * Job code/Mode title
tax1 10.0000% VAT No./Rate
04.00 Lower tax limit
tax2 4.0000% VAT No./Rate
0.00 Lower tax limit
tax3 5.0000% 0.00
2900 TL 1500 TL
2700 TL
– 20 –
[JOB#2119]: DIRECT KEY READING REP.Key operation
STAMP Stamp
01/01/00 0:08 000000 #0005
#2119 *P G M â * Job code/Mode title
ü ü é l1 D ü é Key no./Dept code or PLU codeü ü â l1 D ü â *** When Dept code is assigned to
ü ü ä l1 D ü ä *** the direct key, the same Dept
ü ü à l1 D ü à *** code isassigned to each level.
Çü å é l1 P 000001 l2 P 001001ü å â l1 P 000002 l2 P 001001 Çé å é l1 ---- Ç
2. Programming
[JOB#1110]PROGRAMMING OF DEPT. PRICE
XX: DEPT-CODE = 01 ∼ 50YYYYYY: PRICE = 0 ∼ 999999Preset price is max. 6 digits.Price can be programmed for each dept. If this programming is per-formed, the ECR is automatically programmed to allow preset priceentry even when it has been programmed not to allow preset priceentry in dept. function programming (JOB#2110).
MRS = 000000
[JOB#2110]PROGRAMMING OF DEPT. FUNCTION
XX: DEPT. code = 01 ∼ 50
XXA: Printing on the cashier report A
No 0
Yes 1
XXB: Item validation printing B
Non compulsory 0
Compulsory 1
C, D: Not used (Fixed at "00")
XXE: SICS Function E
Normal 0
Single item cash sale 1
Single item finalize 2
F: Not used (Fixed at "0")
XXG: Amount entry type G
Inhibited 0
Open 1
Preset 2
Open and preset 3
MRS = 0000001
2119 TL
1110 YYYYYYXX
No change
priceDEPT. CODE
For the next DEPT.
TLST
2110 XX
DEPT. CODE
CL
ABCDEFG
For next code
No change
TLST
– 21 –
[JOB#2111]DEPT. TAX STATUS PROGRAMMING
XX: DEPT. CODE = 01 ∼ 50 A, B: Not used (Fixed at "00")
C: VAT 1 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
MRS = 000000
[JOB#2112]DEPT. HALO (limit) preset
XX: DEPT. CODE = 01 ∼ 50A: Mantissa (HALO) = 1 ∼ 9B: Exponent (HALO) = 0 ∼ 7
* Items A and B indicate A × 10B. Any amount below that value isenable within 9999999.
MRS = 17
[JOB#2114]DEPT. TEXT PROGRAMMING
XXX: DEPT. CODE = 01 ∼ 50
Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.
MRS = DPT. XX
[JOB#2115]COMMISSION GROUP PROGRAMMING
XX: DEPT. CODE = 01 ∼ 50A: Group No. = 0~3
[JOB#2116]PROGRAMMING OF DEPT. GROUP
XX: DEPT. code = 01 ∼ 50AA: Group No. = 1 ~ 14
Group No. Group name
1~9 Plus department
10 Minus department
11 Plus HASH department
12 Minus HASH department
13 Plus BR department
14 Minus BR department
MRS = 01
A selection of the group "Hash" and "BR" are inhibited when the hashfunction is programmed as disabled in SRV mode.
[JOB#2119]LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS
DEPT. code is assigned to the key no. Which has been programmedin JOB#951 programming.
AB: DEPT. CODE = 01 ∼ 50
[JOB#1200]Creating/assigning PLUs and the associated departments.
XXXXXX: PLU code = 01 ∼ 999999AB: DEPT. code = 01 ∼ 50
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 01
2111 XX
DEPT. CODE
CL
ABCDEF
For the next DEPT.
No change
ST TL
2112 ABXX
DEPT. CODE
For the next DEPT.
No change
TLST
2114 XX
DEPT. CODE
CL
Character key
For the next DEPT.
No change
ST TL
2115 XX
DEPT. CODE
CL
A
For next code
No change
TLST
2116 XX
DEPT. CODE
CL
AA
Next code
No change
TLST
2119 XXX
KEY No.
Next DEPT.
ABDEPT. code
0
ST TL
1200 XXXXXX
PLU code
AB
No change
ST TL
– 22 –
[JOB#1210]PRICE PROGRAMMING FOR PLUS
XXXXXX: PLU CODE = 1 ∼ 999999YYYYYY: Amount = 0 ∼ 999999
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 000000
[JOB#1211]PLU BASE Q’TY PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999ZZ: Base quantity = 00 ∼ 99
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
[JOB#1220]PROGRAMMING OF PLUS STOCK (ADD)
XXXXXX: PLU code = 1 ∼ 999999YYYY.YYY: Stock value = 0.001 ∼ 9999.999
The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is added to the PLU stock counter.
MRS = 0.000
[JOB#1221]PROGRAMMING OF PLU STOCK (SUB)
XXXXXX: PLU code = 1 ∼ 999999YYYY.YYY: Stock value = 0.001 ∼ 9999.999
The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is subtracted from the PLU stock counter.
MRS = 0.000
[JOB#1222]PROGRAMMING OF PLU STOCK (OVERWRITE)
XXXXXX: PLU code = 1 ∼ 999999YYYYYYY: Stock value = 0.001 ∼ 9999.999
The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is overrited to the PLU stock counter.
MRS = 0.000
[JOB#2210]PLU function programming
XXXXXX: PLU code = 1~999999 A, B: Not used (Fixed at"00")
C: Amount entry type C
Inhibited 0
Open 1
Preset 2
Open and preset 3
Delete 4
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 002
1210 XXXXXX
PLU CODE
YYYYYY
For next code
No change
ST TL
1211 ZZXXXXXX
PLU CODE
For the next PLU
No change
TLST
1220 YYYY.YYYXXXXXX
PLU CODE
For the next PLU
ST TL
1221 XXXXXX
Next codePLU CODE
YYYY.YYY ST TL
1222 XXXXXX
PLU CODE
YYYYYYY
Next code
No change
ST TL
2210 ABCXXXXXX
No change
PLU code
For next codeCL
ST TL
– 23 –
[JOB#2211]PLU TAX STATUS PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999
A: Sign A
+ 0
– 1
XXXXXB: Not used (Fixed at "0")
C: VAT 1 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 000000
[JOB#2214]PLU TEXT PROGRAMMING
XXXXXX: PLU CODE = 1 ∼ 999999Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.
MRS = PLXXXXXX
[JOB#2215]COMMISSION GROUP PROGRAMMING
XXXXXX: PLU code = 1 ~ 999999XXXXXA: Group No. = 0 ~ 3If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
[JOB#2219]PLU CODE DEFINITION FOR DIRECT PLU KEYS
ABCDEF: PLU code = 1~999999
PLU code is assigned to the key No. which has been programmed inJOB#951 programming.
[JOB#2220]LINKED PLU PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999YYYYYY: PLU code = 1 ∼ 999999
When the "ST" key is pressed without entering any number as thefirst PLU code (YYYYYY), the previous data is cleared.
PLU code should already be defined when they are used in program-ming here.
MRS = 0
[JOB#2221]SET PLU PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999YYYYYY: PLU code = 1 ∼ 999999
When the "SBTL" key is pressed without entering any number as thefirst PLU code (YYYYYY), the previous data is cleared.
The PLU code (XXXXXX) can not be set the set PLU code(YYYYYY).
PLU code must already be defined when it is used in programminghere.
MRS = 0
2211 XXXXXXPLU code
CL
ABCDEF
No change
For the next PLU
TLST
2214 XXXXXXPLU code
CL
Character key
For the next PLU
No change
TLST
2215 AXXXXXX
No change
PLU code
For next codeCL
ST TL
2219 ABCDEFXXX
Next code
Key No.
0
PLU code
L3
L1
L2
ST TL
2220 YYYYYYXXXXXX
Max. 5 times
0
PLU CODETLST
2221 YYYYYYXXXXXX
Max. 10 times
0
PLU codeTLST
– 24 –
[JOB#2230]PLU CODE PROGRAMMING (range)
XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999
AB: Dept. code = 1~50
* All are set with the contents of Start PLU setting.
[JOB#2231]PLU function programming (RANGE)
* All are set with the contents of Start PLU setting.XXXXXX: Start PLU code = 1~999999YYYYYY: End PLU code = 1~999999
A, B: Not used (Fixed at "00")
C: Amount entry type C
Inhibited 0
Open 1
Preset 2
Open and preset 3
Delete 4
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 000
[JOB#2232]PLU TAX STATUS PROGRAMMING (RANGE)
* All are set with the contents of Start PLU setting.XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999
A: Sign A
+ 0
– 1
B: Not used (Fixed at "0")
C: VAT 1 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
[JOB#2235]Commission group programming (RANGE)
* All are set with the contents of start PLU setting.XXXXXX: Start PLU code = 1~999999YYYYYY: End PLU code = 1~999999
A: Group No. = 0~3
2230 YYYYYYXXXXXX
PLU CODE
AB
No change ∗
PLU CODE
TLST
2231 XXXXXXPLU CODE
ABC
No change ∗ST TL
CL
YYYYYY
2232 XXXXXX
PLU CODE
ABCDEF
No change ∗
YYYYYY
ST TL
2235 YYYYYYXXXXXX
PLU CODE
A
No change ∗TLST
– 25 –
[JOB#1310]RATE PROGRAMMING
XXX: Fanction No.YYYY. YYYY: Rate
FunctionNo.
Function Entry range Remarks
1 (–)1
0 to 9999.99 (–) unit price 2 (–)2
3 (–)3
4 (–)4
5 %1
0 to 100.00 % rate 6 %2
7 %3
8 %4
51 Exchange 10 to 9999.9999 Rate 52 Exchange 2
53 Exchange 3
63 Commission 10 to 999.99 Rate 64 Commission 2
65 Commission 3
MRS = 0
[JOB#2311]MISC KEY PROGRAMMING 1
XXX: Function No.
Function No. Function
1 (–)1
2 (–)2
3 (–)3
4 (–)4
5 %1
6 %2
7 %3
8 %4
A: Sign A
+ 0
– 1
B, C, D, E, F: Not used (Fixed at "00000")
MRS = 100000
[JOB#2312, 2322]HALO PROGRAMMING
XXX: Function No.A: Mantissa (0 to 9)B: Exponent (0 to 8)
JOB#Function
No.Function Remarks
2312
1 (–)1Item B is specificablewithin the range from 0 to7.
2 (–)2
3 (–)3
4 (–)4
36 RAItem B is specificablewithin the range from 0 to8.
37 RA2
38 PO
39 PO2
2322
41 CA1
Item B is specificablewithin the range from 0 to8.
42 CA2
43 CH1
44 CH2
45 CH3
46 CH4
47 CR1
48 CR2
49 CR3
50 CR4
Entry range, system: A × 10B
MRS = 17 ((–)1~(–)4)18 (Others)
[JOB#2313]MISCELLANEOUS KEY PROGRAMMING (% HALO)
XXX: Function No.YYY. YY: % HALO
FunctionNo.
Function Remarks
5 %1
6 %2
7 %3
8 %4
1310 YYYY.YYYYXXX
Function No. Rate
No change
TLST
2311 ABCDEFXXX
Function No.
No change
TLST
23122322
ABXXX
Function code
No change
ST TL
2313 YYY.YYXXX
No change
TLST
– 26 –
[JOB#2314]TEXT PROGRAMMING FOR MISC KEYS
XXX: FUNCTION CODE
Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:
XXX → 00 key XXX: CHARACTER CODE (3DIGITS)
Please refer to section 3
F-NO. FUNCTION DEFAULT TEXT
1 (–)1 [~]é
2 (–)2 [~]â
3 (–)3 [~]ä
4 (–)4 [~]à
5 %1 ‰é
6 %2 ‰â
7 %3 ‰ä
8 %4 ‰à
9 SET PLU (–) set plu-
10 DIFFER differ
11 TAXABLE1 ST tax1 st
12 TAXABLE2 ST tax2 st
13 TAXABLE3 ST tax3 st
14 TAXABLE ST tax st
15 VAT/TAX 1 vat 1
16 VAT/TAX 2 vat 2
17 VAT/TAX 3 vat 3
18 VAT/TAX vat
19 NET1 NETé
20 NET2 NETâ
21 COUPON PLU cp plu
22 REFUND refund
23 VOID "
24 VOID MODE " mode
25 MANAGER VOID mgr "
26 SBTL VOID sbtl "
27 HASH VOID hash "
28 HASH REFUND hash rf
29 VAT SHIFT vat sft
30 VAT/TAX DELETE tax dele
31 VP COUNTER vp cnt
32 NO SALE no sale
33 G.C. COUNTER g. c. cnt
34
35
36 RA ***ra
37 RA2 ***ra2
38 PO ***po
39 PO2 ***po2
F-NO. FUNCTION DEFAULT TEXT
40 CHECK CASHING ca/chk
41 CASH C ash
42 CASH2 C ash2
43 CHECK1 check
44 CHECK2 check2
45 CHECK3 check3
46 CHECK4 check4
47 CREDIT1 credit1
48 CREDIT2 credit2
49 CREDIT3 credit3
50 CREDIT4 credit4
51 EXCHANGE1 exch1
52 EXCHANGE2 exch2
53 EXCHANGE3 exch3
54 EXCHANGE4 exch4
55 EXCHANGE1 IS exch1 is
56 EXCHANGE2 IS exch2 is
57 EXCHANGE3 IS exch3 is
58 CASH IN DRAWER ****cid
59 CASH/CHECK IS ca/ch is
60 CASH/CHECK IN DRAWER ca/ch id
61 CHECK CHANGE chk/cg
62 GUEST guest
63 COMMISSION SALE1 com.sal1
64 COMMISSION SALE2 com.sal2
65 COMMISSION SALE3 com.sal3
66 NON COMMISSION SALE non com.
67 ORDER TOTAL order tl
68 PAID TOTAL paid tl
69 DOMESTIC CURRENCY1 dom.cur1
70 DOMESTIC CURRENCY2 dom.cur2
71 DOMESTIC CURRENCY3 dom.cur3
72 DOMESTIC CURRENCY4 dom.cur4
73 CHECK IN DRAWER *ch id
74 (+) DEPT TOTAL *dept tl
75 (–) DEPT TOTAL dept(-)
76 HASH (+) DPT TOTAL *hash tl
77 HASH (–) DPT TOTAL hash(-)
78 BOTTLE (+) TOTAL *bttl tl
79 BOTTLE (–) TOTAL bttl(-)
80 NET 1 (TAXABLE-VAT1) net 1
81 NET 2 (TAXABLE-VAT2) net 2
82 NET 3 (TAXABLE-VAT3) net 3
83 NET (TAXABLE-VAT) net
84 SUBTOTAL subtotal
85 MDS SBTL mdse st
86 TOTAL ***total
87 CHANGE change
88 DUE due
89 ITEMS items
90 PLU ST plu st
2314 Character keyXXX
Function number Max. 8 char.
No change
TLST
– 27 –
F-NO. FUNCTION DEFAULT TEXT
91 COPY RCPT TITLE COPY
92 G.C. COPY TITLE g.c. copy
93 AVERAGE ave.
94 GROUP1 Group01
95 GROUP2 Group02
96 GROUP3 Group03
97 GROUP4 Group04
98 GROUP5 Group05
99 GROUP6 Group06
100 GROUP7 Group07
101 GROUP8 Group08
102 GROUP9 Group09
103 CCD CCD
104 CCD DIFFER ccd dif.
105 CCD DIFFER TOTAL dif. tl
106 ORDER TL-PAID TL O ~ P
107 COMMISSION AMOUNT1 com. amt1
108 COMMISSION AMOUNT2 com. amt2
109 COMMISSION AMOUNT3 com. amt3
110 COMMISSION AMOUNT TTL com. ttl
111 DEPT. REPO. TITLE DEPT
112 GROUP REPO. TITLE group
113 PLU REPO. TITLE PLU
114 STOCK REPO. TITLE stock
115 TRANS. REPO. TITLE trans.
116 CID REPO. TITLE tl-id
117 COM. SALES REPO. TITLE sales
118 CASHIER REPO. TITLE cashier
119 HOURLY REPO. TITLE hourly
120 DAILY NET REPO. TITLE daily
121 SET PLU TITLE set plu
122 TOTAL TAX ttl tax
123 NET WITHOUT TAX NET
124 ZERO SALES REPRT TITLE zero sal
125 CATEGORY REPO. TITLE category
126 DIFFER SUBTOTAL diff st
[JOB#2315]MISC KEY PROGRAMMING (%)
XXX: Function No.
A: % type ASubtotal % 0Item % 1
Function No. Function Remarks5 %16 %27 %38 %4
MRS = 0
[JOB#2316]MISC KEY PROGRAMMING ($ )
XXX: Function No.
A: $ type A
Subtotal $ 0
Item $ 1
Function No. Function Remarks
1 (—) 1
2 (—) 2
3 (—) 3
4 (—) 4
MRS = 0
[JOB#2320]MEDIA KEY PROGRAMMING
XXX: Function No.
FunctionNo.
Function A B C D E F G H I J K
41 CA1 É F F F F — — — — F F
42 CA2 É F F F F — — — — F F
43 CH1 F F F F F — — — — F F
44 CH2 F F F F F — — — — F F
45 CH3 F F F F F — — — — F F
46 CH4 F F F F F — — — — F F
47 CR1 F F F F F — — — — F F
48 CR2 F F F F F — — — — F F
49 CR3 F F F F F — — — — F F
50 CR4 F F F F F — — — — F F
* Items marked with on (F ) are programmable.
A: EFT function A
Non compulsory 0
Compulsory 1
B: Footer print B
No 0
Yes 1
C: Non-add code entry C
Non compulsory 0
Compulsory 1
D: Change due D
Enable 0
Disable 1
E: VP E
Non compulsory 0
Compulsory 1
F, G, H, I: Not used (Fixed at "0000")
2315 XXX A
No change
ST TL
2316 XXX A
No change
ST TL
2320 XXX ABCDEFGHIJK
No change
ST TL
– 28 –
J: Drawer opening J
Yes 0
No 1
K: Entry of amount tended K
Non compulsory (Cash, Check)Inhibit (CR1 to CR8)
0
Compulsory 1
MRS=00000000000
[JOB#2321]MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)
XXX: Function No.YYYYYYYYY: Limitation amount
Func. No.
Function Entry range MRS
586140
CID (Sentinel)CHK CHANGECA/CHK
0 to 9999999.990 to 999999.990 to 999999.99
9999999.99 999999.99 999999.99
[JOB#1500]CASHIER CODE DIFINITION
XXX: Cashier No.= 1 ∼ 15YYYY: Cashier code = 00 ∼ 99
MRS = 01;1, 02;2, 03;3, 04;4, 05;5, 06;6 ~ 15;15
[JOB#1514]CASHIER NAME PROGRAMMING
YYYY: Cashier code = 01 ∼ 99Characters can be entered by using character keys or numeric keys.The key entry sequence for entering one character by numeric keysis as follows: XXX → 00 KEY XXX: Character code (3 digits)Please refer to section 3.Max. 8 charactersMrs = ’Space’
[JOB#2510]CASHIER PROGRAMMING
YY: Cashier code = 01~99
A: G.C. copy A
Enable 0
Disable 1
B: VAT shift B
Not 0
State 1
C, D: Not used (Fixed at "00")
E: Drawer No. E
Not open 0
Drawer No. 1~2
MRS = 1
[JOB#2610]DATE SETTING
XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year)
* The date entry format complies with the applicable SRV-modeprogramming.
MRS = 010100
[JOB#2611]TIME SETTING
XX: Hour (00 ∼ 23)YY: Minute (00 ∼ 59)
MRS = 0
[JOB#2612]MACHINE NUMBER SETTING
XXXXXX: Machine number (0 ∼ 999999)
MRS = 0
[JOB#2613]CONSECUTIVE NUMBER SETTING
XXXX: Consecutive number (0000 ∼ 9999)
MRS = 0000
2321 XXX YYYYYYYY
No change
ST TL
1500 XX YY
No change
ST TL
1514 YY Character key
No change
TLST
2510 YY ABCDE
No change
ST TL
2610 XXYYZZ TL
0
2611 XXYY TL
0
2612 XXXXXX TL
0
2613 @/FOR CA/ATXXXX
– 29 –
[JOB#2614]LOGO TEXT PROGRAMMING
X: 1 ∼ 6 1 (24 char.)
2 (24 char.)
3 (24 char.)
4 (24 char.)
5 (24 char.)
6 (24 char.)
Character can be entered by using character keys or numeric keys.The key entry sequence for entering one character by numeric keysis as follows:
XXX → 00 Key XXX: Character code (3 digits)Please refer to section 3.
ER-A460 ER-A470
MRS = S H A R P presents the E R ~ A à ç ü S H A R P I S T H E B E S T
S H A R P presents the E R ~ A à ê ü S H A R P I S T H E B E S T
NOTE: This programming is related to JOB# 912D programming.Only when "6-line header instead of a stamp" is selected byJOB# 912D programming, all 6 lines are programmable.When "3-line header" is selected, upper 3 lines (1st-3rd line)are programmable.When "3-line footer" is selected, lower 3 lines (4th-6th line)are programmable.
[JOB#2615]Programming of the limits to TRY ST feed line and No. of times ofvalidation printing.
Y: No. of times of validation printing = 0 ∼ 9 X: Feed line after depression
of differ ST key. = 0 ∼ 9
MRS = 10
[JOB#2616]OPTIONAL FEATURE
X: 1 MRS = 00000000
A: OP X/Z report A
Enable 0
Disable 1
B: PO operation in REG mode B
Enable 0
Disable 1
C: Not used (Fixed at "0")
D: "RFND" key entry in REG mode D
Enable 0
Disable 1
E: Direct void function in REG mode E
Enable 0
Disable 1
F: Indirect void in REG mode F
Enable 0
Disable 1
G: Subtotal void in REG mode G
Enable 0
Disable 1
H: Refund VP H
Non compulsory 0
Compulsory 1
2614 Character keyX
Position code
No change
ST TL
2615 YX
0
TL
2616 ABCDEFGH
0
X ST TL
– 30 –
X: 2 MRS = 00000000
A: The first last item void A
Enable 0
Disable 1
B: PLU level shift system B
Auto 0
Manual 1
C: PLU level shift system C
MGR & REG mode 0
MGR mode 1
D: Printing of the number of purchases D
No 0
Yes 1
E: Time print E
Yes 0
No 1
F: Printing of journal F
Full print 0
Journal select 1
G: Item VP G
Enable 0
Disable 1
H: (–) VP H
Non compulsory 0
Compulsory 1
X: 3 MRS = 00000000A, B: Not used (Fixed at "00")
C: Zero skip in Cashier report C
Yes 0
No 1
D: Zero skip in Transaction report D
Yes 0
No 1
E: Zero skip in Dept. report E
Yes 0
No 1
F: Zero skip in PLU report F
Yes 0
No 1
G: Zero skip in Hourly report G
Yes 0
No 1
H: Zero skip in Daily net report H
Yes 0
No 1
X: 4 MRS = 00000000A, B: Not used (Fixed at "00")
C: Vat/Tax amount printing on R/J C
Yes 0
No 1
D: Taxable amount printing on R/J D
Yes 0
No 1
E: Net amount printing on R/J E
Yes 0
No 1
F, G: Not used (Fixed at "00")
H: When PLU level system is "Auto" (X:2 B = 0), PLUlevel returns method
H
By one item 0
By one receipt 1
X: 5 MRS = 00000000A, B, C: Not used (Fixed at "000")
D: VAT shift system D
By cashier 0
By shift key 1
E, F, G, H: Not used (Fixed at "0000")
X: 6 NOT USED MRS = 00000000
X: 7 NOT USED MRS = 00000000
X: 8 NOT USED MRS = 00000000
X: 9 NOT USED MRS = 00000000
X: 10 NOT USED MRS = 00000000
X: 11 NOT USED MRS = 00000000
X: 12 NOT USED MRS = 00000000
X: 13 MRS = 00000000
A: Credit totalizer update if RA/PO finalized by Creditkey
A
No 0
Yes 1
B: Separator line in report B
1 line 0
Separator line 1
C, D, E, F, G, H: Not used (Fixed at "000000")
[JOB#2617]PROGRAMMING OF THE TIME INTERVAL FOR THE DRAWERALARM
XXX: 0 ∼ 255 sec
MRS = 000
2617 XXX
0
TL
– 31 –
[JOB#2619]HOURLY REPORT (Starting time)
a: Memory format A
30 minutes (24 hour) 0
15 minutes (12 hour) 1
bb: Starting time (hour): 00 ∼ 23
ex) Case 1.
X1 Hourly report (#160) (15 min, start time = 7]
#160 7:00 (data) 7:15 (data) 7:30
12 hour started from 7:00
(data)
7:45 (data) subtotal (data)
| |
18:45 (data) subtotal (data) **:** (data) Data out of range (19:00 to 6:59)
[JOB#2620]STACK REPORT
XX: JOB#SSSSSS: Start codeEEEEEE: End code
JOB# REPORT NAME TYPE
00 General
10 DEPT./GROUP
13 DEPT. All group
20 PLU RANGE
24 PLU stock RANGE
27 PLU zero sales
29 PLU price category RANGE
30 Transaction
31 CID
32 Commission sale
50 All cashier
60 Hourly RANGE (only X report)
70 Daily net
[** ]Max. 70 step are programmable. "1 step" means the memory sizeused for one no range type JOB#.The RANGE type JOB# means "8 steps".
For example)The memory size for programming JOB#00, 20 and 50 is 10 steps.(ie. 1 step for JOB#00, 8 step for JOB#20, and 1 step for JOB#50. )
[JOB#2630, 2631, 2632]SECRET CODE PROGRAMMING
#2630: PGM1 mode#2631: X1/Z1 mode#2632: X2/Z2 mode
* If "0" is entered, "compulsory secret code entry" is canceled.
MRS = 0
2619 abb
0
TL
2619 107 TL
2620
XX SSSSSS EEEEEE
All delete
No range
Next JOB# (max.=20)
ST TL
2630,2631,2632 XXYY
0
TL
– 32 –
[JOB#2641]MESSAGE TEXT PROGRAMMING
X: Message No. = 1~87
Message No.
Description MRS
1 Registration error ENTRY ERROR
2 Misoperation error MISOPERATION
3Desired code is notprogrammed yet.
NO RECORD
4 Paper empty PAPER EMPTY
5 Secret code error SECRET CODE
6 (reserved)
7 Memory is full MEMORY FULL
8 (reserved)
9 (reserved)
10 Stock is empty OUT OF STOCK
11Compulsory of pushing the STkey
SBTL COMPUL.
12 Compulsory of tendering TEND COMPUL.
13 (reserved)
14 (reserved)
15 (reserved)
16 (reserved)
17 (reserved)
18 (reserved)
19 (reserved)
20 (reserved)
21 (reserved)
22 Cashier changing error CASHIER ERR.
23 Cashier entry error ENTRY ERR CA
24 (reserved)
25 (reserved)
26 (reserved)
27 (reserved)
28 (reserved)
29 (reserved)
30 (reserved)
31Compulsory of non-add codeentry
# COMPULSORY
32The cashier key is not pushedor inserted.
NOT ASSIGNED
33The clerk key is changed in thetransaction
NOT CHANGE
34 Overflow limitation OVER LIMIT.
35 The open price entry is inhibited. INH. OPEN PR
36 The unit price entry is inhibited. INH. UNIT PR
37The direct non-tenderingfinalization after previous tenderentry is inhibited.
NOT NON-TEND
38Service interruption duringValidation printing
P.OFF. IN VP
39 (reserved)
40 (reserved)
41 (reserved)
42 (reserved)
Message No.
Description MRS
43 (reserved)
44 (reserved)
45 (reserved)
46 (reserved)
47 (reserved)
48 (reserved)
49 (reserved)
50 (reserved)
51 (reserved)
52 (reserved)
53 (reserved)
54 (reserved)
55 (reserved)
56 (reserved)
57 (reserved)
58 (reserved)
59 (reserved)
60 (reserved)
61 (reserved)
62 (reserved)
63 (reserved)
64 (reserved)
65 (reserved)
66 (reserved)
67 REG Buffer full BUFFER FULL
68 (reserved)
69 (reserved)
70 (reserved)
71 (reserved)
72 EFT ERROR EFT ERROR
73 EFT BREAK EFT BREAK
74 (reserved)
75 (reserved)
76 Closed drawer error CLOSE DRAWER
77 (reserved)
78 (reserved)
79 (reserved)
80 (reserved)
81 Enter secret code ENTR SECRET#
82 IR sending SEND
83 IR receiving RECEIVE
84 IR send success SEND OK
85 IR reserve success RECEIVE OK
86 IR communication error COM. ERROR
87 IR data format error DATA ERROR
88 IR time out error TIME OUT
89 IR (zaurus) cancel CANCEL
Amessage is 12 characters
Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:XXX → 00 key XXX: Character code (3 digits)Please refer to section 3
Important Note: Change of Message text under this programmingrequires installation of optional ER-01/02 RA RAMchip and creation of File Group No. 16.
2641 Character keyXX
Message No.
No change
ST TL
– 33 –
[JOB#2644]GUIDANCE TEXT PROGRAMMING FOR EASY PROGRAMMING
XX: Guidance No. = 1~132
Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:XXX → 00 key XXX: Character code (3 digits)Please refer to section 3
1 text max. 12 characters
No. MRS JOB No.
1 DEPT PRICE #1110
2 DEPT FUNC. #2110
3 DEPT TAXABLE #2111
4 DEPT HALO #2112
5 DEPT TEXT #2114
6 DEPT COM. GRP #2115
7 DEPT GROUP #2116
8 DEPT DRCTKEY #2119
9 PLU ASG.DEPT #1200
10 PLU PRICE #1210
11 PLU BASE QTY #1211
12 PLU STCK ADD #1220
13 PLU STCK SUB #1221
14 PLU STCK OVW #1222
15 PLU FUNCTION #2210
16 PLU TAXABLE #2211
17 PLU TEXT #2214
18 PLU COM. GRP #2215
19 PLU DRCT KEY #2219
20 LINK PLU #2220
21 SET PLU #2221
22 PLU CODE RNG #2230
23 PLU FUNC RNG #2231
24 PLU STTS RNG #2232
25 PLU COM RNG #2235
26 RATE PRGRAM #1310
27 MISC KEY PGM #2311
28 FNC KEY HALO #2312
29 MDIAKEY HALO #2322
30 % HALO #2313
31 FUNC TEXT #2314
32 MISC KEY PGM #2315
33 MISC KEY PGM #2316
34 MDIA KEY PGM #2320
35 MDIAKEY HALO #2321
36 CSR CODE PGM #1500
37 CSR NAME PGM #1514
38 CSR PGM #2510
39 DATE PROGRAM #2610
40 TIME PROGRAM #2611
41 MCHN NO. PGM #2612
42 CC NO. PGM #2613
43 LOGOTEXT PGM #2614
44 VP,TRY FEED #2615
45 OPT FEATURE #2616
No. MRS JOB No.
46 DRAWER ALERM #2617
47 HOURLYREPORT #2619
48 STACK REPORT #2620
49 SECRET(TEXT) #2630
50 SECRET(X1Z1) #2631
51 SECRET(X2Z2) #2632
52 MESSGE TEXT #2641
53 GUID TEXT #2644
54 TAX RATE #2711
55 PRICE #1110/#1210
56 ENTER DEPT# #1200/#2230
57 SIGN (–) #2111-A/#2211-A/#2311-A
58 SIGN (+) #2232-A
59 TAXABLE1: YES #2111-F/#2211-F/#2311-F
60 TAXABLE1: NO #2232-F
61 TAXABLE2: YES #2111-E/#2211-E/#2311-E
62 TAXABLE2: NO #2232-E
63 TAXABLE3: YES #2111-D/#2211-D/#2311-D
64 TAXABLE3: NO #2232-D
65 VAT: YES
66 VAT: NO
67 PRT CSR: YES #2110-A
68 PRT CSR: NO
69 VP COMPL: YES #2110-B/#2320-E
70 VP COMPL: NO
71 SIF #2110-E
72 SICS
73 NORMAL
74 DELETE #2210-C
75 OPEN&PREST #2110-G/#2231-C
76 PRESET
77 OPEN
78 INHIBITED
79 HALO(EXP.) #2112/#2312/#2322
80 HALO(AMOUNT) #2321
81 HALO(RATE) #2313
82 COM. GRP #2115/#2215/#2235
83 GROUP #2116
84 BASE Q’TY #2118
85 STOCK(ADD) #1220
86 STOCK(SUB) #1221
87 STOCK(OVER) #1222
88 RATE #1310
89 ITEM #2315
90 ST #2316
91 EFT CMPL #2320-A
92 EFT NONCMPL
93 FOOTER: YES #2320-B
94 FOOTER: NO
95 # CMPL #2320-C
96 # NONCMPL
97 DUE DISABLE #2320-D
98 DUE ENABLE
99 DRW OPEN: YES #2320-J
100 DRW OPEN: NO
101 TND CMPL: YES #2320-K
102 TND CMPL: NO
103 TND INH.
2644 Character keyXX
Guidance No.
No change
ST TL
– 34 –
No. MRS JOB No.
104 ENTER PLU# #2220/#2221
105 ENT.CSR CODE #1500
106 ENT.CSR NO
107 ENT.DRW# #2510
108 G.C. COPY: YES
109 G.C. COPY: NO
110 VAT SFT STAT
111 VAT SFT NOT
112 ENT.DEPT# #1110/#2110/#2111/#2112/#2114/#2116
113 ENT.KEY# #2119/#2219
114 ENT.FUNC# #1310/#2311/#2312/#2322/#2313/#2314/#2315/#2316/#2320/#2321
115 #2320/#2321
116 ENT.POS.CODE #2614
117 ENTER TAX NO #2710/#2711
118 ENT.TAX RATE
119 LOWER TAX
120 ENTER MSG NO #2641
121(FIXED DATA) The message for "Fixed"
or "Not used" data
122ENTER [00] KEY For changing character
key layout.
123 PC-LINK SEND #0996
124 PC-LINK RCV. #0998
125 ZAURUS RCV. #1996
126 ONL T. NO. #6110
127 ONL MODEM #6111
128 ONL BAUDRATE #6112
129 ONL CODE #6113
130 ONL TIMER #6114
Important Note: Change of Guidance text under this programmingrequires installation of optional ER-01/02 RA RAMchip and creation of File Group No. 17.
[JOB#2711]TAX RATE PROGRAMMING
* DEPRESSION OF THE ST KEY AT FOLLOWING POINTS PER-FORM A TAX TABLE DELETE OPERATION.
A: Tax programming A
Tax1 1
Tax2 2
Tax3 3
Y: Sign y
+ 0
– 1
xxx.xxxx: Rate = 0.0000~100.0000%LOWER TAX LIMITATION max. 999.99(This is invalid in VAT system.)
MRS = 0
2711 YXXX.XXXXA
Declaration of TAX TAX rate
XXXXX
Lower tax limitfor add tax.
When lower taxlimit is 0.
0
0
TL
TL
– 35 –
[JOB#2900]
<CAUTION>(This JOB must be performed at X2/Z2 mode position.)
AUTO KEY SETTING
(Auto key function)
• This machine has [AUTO] key which can be programmed by thefollowing key-sequence.
• When [AUTO] key is depressed, the machine works the same asthe programmed key-sequence programed.
<Example>Mode switch ⇓(X2/Z2)
(REG)
(X2/Z2)
(REG)
2900 (Free key)AUTO
Max.25
TL
AUTO2
AUTO3
AUTO4
AUTO5
AUTO
AUTO2
AUTO3
AUTO4
AUTO5
Delete
2900 AUTO PLU1 100 DEPT2 AUTO TL
Key entry R/J Display Comment
AUTO PL000001 * 1.10
DEPT02 * 1.00
PL0000001 same as entryPLU11.10
1
10
100
DEPT02 1.10
same as entry1
same as entry0
same as entry0
same as entryDEPT2
2900 AUTO2 PLU1 100 DEPT2 AUTO2 TL
Key entry R/J Display Comment
DEPT 1 DEPT01 DEPT01 1.10
100
CHANGE 0.00
same as entry1
same as entry0
same as entry0
same as entryTL
AUTO 2
* 1.00
*** TOTAL * 1.00
CASH * 1.00
CHANGE * 0.00
10
1
– 36 –
3. Character assignment method
The ER-A460/A470 has two kinds of method at character assign-ment.One is to use alphabetic assigned key and other one is to use tenkeys one is to use ER-01RK.
∼ Using alphabetic assignment method ∼Push alphabetic
Repeat
TL
Programming key layout
1 ER-A460
2 ER-A470
* When the ‘SHIFT’ key is depressed, this character can be preset with small character.
(SHIFT)
1 2 3
4 5 6
7 8 9
0
$BACK
SPACE
(SPACE)
(DC) A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
ST
TL
(SHIFT) (DC) ST
1 2 3
4 5 6
7 8 9
0 00
CL
(DEL)
( ) ( )BACK
SPACE
><
Pt
1 2 3 4 5 6 7 8 9 0
@! # $ ^ & ( )%
?
[ ]!!?
G H
I
J K L
MN
O PQ R
S
T U
V
W
X
Y
Z
A
B
E
D F
C
(SPACE) (SPACE) (SPACE) (SPACE) (SPACE) = - +
;:
/
000 TL
!
ß
§
¤
ØÆ
Ç
£
Ω
Ψ
Υ
Π
Λ
∆Γ
Θ
≡
Σ
Φ
.,
– 37 –
3 ER-01RK * Ten Key/CL key input by remote control key
Ten key function is set to the remote control key for use other thantext input.Keys to be used and their corresponding keys on the ECR
Keys on the remote control Key on the ECR
0, 1 ∼ 9 0, 1 ∼ 9
[00] [00]
(←) [X], [@/FOR]
(→) [ . ]
[ . ] [ . ]
[ST] [SBTL]
[CL] [CL]
If a remote control key other than the above is pressed in a caseother than character input, it is invalid. (the key input is not ac-cepted.)
[TL] key is not provided on the remote control. (After completion ofsetting, press [TL] key on the ECR.)
The remote control keys can be used only in PGM1/PGM2 modes.
For the remote control key layout, refer to the separate sheet.
* The following key marks show the following functions:
Used as:
Keys Normal mode Character entry mode
& key Left cursor key
. key Right cursor key
(BS) — Back space key
(CL) Clear key Clear key
1 !
Numeric key
Numeric key
2 @
3 #
4 $
5 %
6 +
7 &
8 *
9 (
0 )
(SPC) / —A space key or thecharacter key("/")
(00) It used to go into thecharacter entry mode.
—
(SML) —used for entering lettersin lower case.
(SHIFT) —used for entering theright side letter.
(DC) —
used for enteringcharacters in doublesize.
(ST) ) key used for kimination afterone item programming
(BS) (CL)( )
1 2 3 4 $#@!
5 6 7 8 *&+%
9 0 )( - ? =
?
A B C [ ]D
E F G H
( )
I J K L
M N O P
Q R S T
U V W X
Y Z
£ ¢ ß Ç
Pt
!§ !!
( ) ( ) Æ ( ) ( )Ø
; :( ) ( ) ( ) ( )
/ (00)
(ST)(DC)(SHIFT)(SML)
ER-01RK
X
(SPC)
@( )×
( )·
– 38 –
* General instructions for programming alphanumeric charactersusing the ER-01RK
This programming remote keyboard allows you to program variousitems instead of using the keyboard of the cash register.The basic instruction for programming with the remote keyboard isthe same as the one with the keyboard of the register. In this part,the method for programming alphanumeric characters is de-scribed.
Note: Both PGM1 and PGM2 modes are available for this pro-gramming.
Procedure
* 1 Letters of alphabets "A" through "Z" are possible to be enteredin lower case or in upper case. By default, the upper-caseletter mode is selected. To enter the character in lower case,press the (SML) key before you enter the character. TheSML lamp lights up. To return to the upper-case letter mode,press the (SML) key again.
Example: To enter "aA", do the following:
* 2 Characters are possible to be entered in single size or in dou-ble size. By default, the single-size character mode is se-lected. To enter the character in double size, press the (DC) key before you enter the character. The DC lamp lightsup. To return to the single-size character mode, press the (DC) key again.
Example: To enter " ", do the following:
* 3 Each character key has two levels. For example, with the A key, you can enter "A" or "". Under the normal condi-tion, the left side letter is selected. To use the right sideletter, press the (SHIFT) key just before you press a key.
Example: To enter "Aa[", do the following:
* 4 "( )", "( )", "( ~ )", "( )", "( )", "( )", "( )", and "( )" areused only for combination with a character key. If the combina-tion is unavailable, only a character key is entered.
Example: To enter "Ä", do the following:
To enter "ä", do the following:
(SHIFT)(DC)(SML)
To enter the characterin the current case
To enter the characterin the current size
*1 *2 *3
To enter in theleft side letter
One of the ( ), ( ), ( ),( ), ( ), ( ), ( ), ( )keys
*4
To use key combination
A characterkey
To enter next character
A (SML) A (SML)
aAA
(SML) (DC) A (SML) A (DC)A
(SML)A (SHIFT)A C
(SHIFT) ; ( ) A
(SML) (SHIFT) ; ( ) A
– 39 –
4 Using ten key of ECR
Note: 00 key is used to enter each 3 digit alpha code.
00XXX
3 digits
Repeat
TL
CODE TABLE FOR ALPHA DESCRIPTOR PROGRAMMING
CODE CHARACTER
001 á
002 â
003 ê
004 î
005 ì
006 í
007 ô
008 ó
009 û
010 ú
011 œ
012 ü
013 ú
014 ö
015 ó
016 Λ017 Ψ018 Γ019 ⋅⋅
020 Ω021 ∆022 Θ023 Ξ024 Π025 Σ026 ϒ027 Φ028
029 Ú
030
031 Ó
033 !
034 "
035 #
036 $
037 %
038 &
039 ’
040 (
041 )
042 *
043 +
044 ,
CODE CHARACTER
045 –
046 .
047 /
048 0
049 1
050 2
051 3
052 4
053 5
054 6
055 7
056 8
057 9
058 :
059 ;
060 <
061 =
062 >
063 ?
064 @
065 A
066 B
067 C
068 D
069 E
070 F
071 G
072 H
073 I
074 J
075 K
076 L
077 M
078 N
079 O
080 P
081 Q
082 R
083 S
084 T
085 U
086 V
087 W
CODE CHARACTER
088 X
089 Y
090 Z
091 Ä
092 Ö
093 Ü
094 ^
095 _
096 ‘
097 a
098 b
099 c
100 d
101 e
102 f
103 g
104 h
105 i
106 j
107 k
108 l
109 m
110 n
111 o
112 p
113 q
114 r
115 s
116 t
117 u
118 v
119 w
120 x
121 y
122 z
123
124 |
125
126 β127
128 !!
129 1
130 2
CODE CHARACTER
131 3
132 4
133 1⁄2134 FT
135 ←136 →137 Ä
138 \
139 e
140 d
141 F
142 T
143 ↓144 ç
145 o
146 ¿
147 Ù
148 à
149 Æ
150 φ151 Å
152 ¤
153 é
154 è
155 Pt
156 ¡
157 Ñ
158 ò
159 £
177 Á
178 Í
180 A181 a
182 E
183 e
184 I
185 i
186 U
187 u
188
189
192
193
CODE CHARACTER
194
195
196
197
198
199
200
201
203 ‰
204 d−
205 ‡
206 §
208 P
209 ç
210 ë
211 †
212 ç
213 ¡
214 ÿ
215 u•
216 æ
217 ∨
218 å
219 ©
224 *
225 §
226 ∅227 ∧
228 ↑229 ]
230 [
231
232 ä
233 ö
234 ü
235 æ
236 å
237 É
238 ñ
253 DC
U
O
c N,n,c
G
S
G,<g
K,k,L,l,
´
DC: DOUBLE CODEFig. 7-2
– 40 –
CHAPTER 3. OP X/Z, X1/Z1,X2/Z2MODEThe following categories of reports can be printed by the ECR.
1) OP X/Z reports (individual clerk reports)
2) X1/Z1 reports (Daily sales total X and Z reports)
3) X2/Z2 reports (Periodic total X and Z reports)
To print reports, use the following key entry sequence
JOB# Range is required
Reading
Resetting
TL
MODE * 1
OP X/Z X1/Z1 X2/Z2 F-read * 3 DATA FOR
REPORT NAME X Z X1 Z1 X2 Z2 X1 * 4 JOB# READING NOTE
GENERAL F F F F 00 —
DEPT/GROUP F F F 10 —
IND. GROUP F F 12 GROUP No.
GROUP TOTAL F F 13 —
PLU BY RANGE F F F F 20 PLU CODE * 2
PLU BY DEPT F F 21 DPT CODE
PLU STOCK F 24 PLU CODE * 2
PLU ZERO SALES F F 27 ALL
PLU PRICE CATEGORY F F 29 PRICE * 2
TRANSACTION F F 30 —
TL-ID F F 31 — ALL CASHIER
COMMISSION SALES F F 32 —
ALL CASHIER F F F F 50 —
IND. CASHIER F F F F F F 51 —
HOURLY (ALL) F F 60
HOURLY (RANGE) F 60 * 2
DAILY NET F F F 70
STACKED REP F F F F 90
* 1 X1: Daily X report Z1: Daily Z reportX2: Periodic X report Z2: Periodic Z report
Stop of printing reports:The printing of all reports can be stopped by the following operation.
Set the mode switch to "MRG" to cancel.
Note) When the printing is stopped, the consecutive number or Zcounter don’t return to the original value.When Z reports, Memory is not reset.In In-line system, when Master has consolidated the data fromthe satellite, ECR can not stop the printing.
* 1 X1: Daily X reportX2: Periodic X report
Z1: Daily Z reportZ2: Periodic Z report
* 2 PLU code range can be specified by entering the start and endnumbers according to the following procedure. When specifyinga single time interval, PLU code, the start number has only to beentered.
* 3 When 2 is entered in the third digit of a job code, periodic reportsare printed.Example: Daily general report; job code 100
Periodic general report; job code 200* 4 Reading display only
→ KEY → CL (Display amount) (Display initialize)
KEY DEPT = DEPTn keyCID = ⊗ keyDaily Net = ST key
• An individual report is printed on the receipt and journal when theTL key is pressed.
• Pressing the decimal point key just after the enery of a job codeclears the corresponding data in the ECR. (Z report)(When printing those reports for which no Z reports can be taken,the decimal point key cannot be pressed after the entry of a jobcode.)
• When the decimal point key is not pressed after the entry of a jobcode, the corresponding data is held in the ECR. (X report)
XXXX
All
Start No.XXXX
End No.
– 41 –