mise en place (ca)
TRANSCRIPT
CHAPTER IV: INTRODUCTION TO CULINARY TECHNIQUES AND PRINCIPLES
Mise en Place (Meeze-ahn-plahs)
A French phrase that means “put in place”
The preparation and assembly of ingredients, pans, utensils and plates or serving pieces needed for a particular dish or service period.
22 Dec 07 2
Mise en Place (Meeze-ahn-plahs)Preparing the ingredients correctly.
Gathering together the tools needed to do the work.
Setting up your work place.
22 Dec 07 3
DEFINITION OF COOKING TERMS
1. BEAT- to introduce air in a
mixture using a brisk regular motion with a wire whip or whisk.
22 Dec 07 5
2. BLANCH- to submerge food in
boiling water for at least three minutes
22 Dec 07 6
3. BOIL- to cook in hot water
usually at 100˚C.
22 Dec 07 7
4. CARAMELIZE- to heat sugar until
it turns golden brown and a characteristic develops.
22 Dec 07 8
5. BRAISE- to cook in a small
amount of liquid in a covered pot.
22 Dec 07 9
6. BROIL- to cook by direct
heat. (GRILL)
22 Dec 07 10
7. BASTE- to moisten food
while cooking to add flavor and prevent drying of surface.
22 Dec 07 11
8. FRY- to cook in fat; stir-fry
or sauté when cooked in a small amount of fat and deep fry when cooked in large amount of fat.
22 Dec 07 12
9. MARINATE- to allow food to
stand in an acid-soy sauce mixture as in barbecue.
22 Dec 07 13
10. ROAST- to cook big or small
whole food in an open fire.
22 Dec 07 14
11. SCALD- to heat milk just
below boiling point.
22 Dec 07 15
12. STEAM- to cook in a steam
with or without pressure as in steamer or pressure cooker.
22 Dec 07 16
14. STEW- to cook in a small
quantity of liquid.
22 Dec 07 17
16. TOAST- to brown (as in
bread) by dry heat.
22 Dec 07 18
17. WHIP- to beat rapidly as
to produce expansion as in cream and egg white.
22 Dec 07 19
BASIC KNIFE USE
PARTS OF A KNIFE
1. BLADE2. TANG3. HANDLE4. RIVETS5. BOLSTERS
22 Dec 07 21
BLADE- the flat cutting
part or edge of a knife.
22 Dec 07 22
TANG- This is the
continuation of the blade that extends into the knife’s handle.
FULL TANG PARTIAL TANG RAT-TAIL TANG
22 Dec 07 23
HANDLE- this should fit the
hand comfortably. An ideal material for a knife is the rosewood, it has no grain and is extremely tough.
22 Dec 07 24
RIVETS- are metal fasteners
used to secure the tang to the handle.
22 Dec 07 25
BOLSTER- is the collar or
shank of the knife that meets the blade to the handle.
22 Dec 07 26
SHARPENING AND HONING
STONES are used to sharpen the edge once it has grown dull through ordinary use. STEELS are used to remove the burrs on a knife after sharpening and to realign the edge on your blade as you work.
22 Dec 07 27
BASIC CUTS
TRIMMING AND PEELINGUse peelers to remove thin skins from carrots, potatoes and similar items. (It works in both directions)
Use a pairing knife to trim or remove stems and ends from vegetables and fruits.
22 Dec 07 29
CHOPPING AND MINCING
- the term chopping is sometimes used interchangeably with mincing, but minced foods are generally cut into a finer size.
22 Dec 07 30
CHOPPING AND MINCINGTrim the root and stem ends and peel the item if necessary.
Slice or chop the food at nearly regular intervals until the cuts are relatively uniform.
22 Dec 07 31
CHIFFONADE (shiff-en-odd)Roll individual leaves into tight cylinders or stack them before cutting.
Use a chef’s knife to make very fine, parallel cuts for a fine, even shred.
22 Dec 07 32
JULIENNE AND BATONNETJulienne and batonnet are long rectangular cuts.Julienne – (1/8 x 1/8 x 1 to 2 inches) or (4 x 4 x 25 to 50 mm)Batonnet – (¼ x ¼ x 2 ½ inches) or (6 x 6 x 50 to 62 mm)
22 Dec 07 33
DICEDicing produces a cube-shaped cut.
Brunoise – (1/8 inch or 4 mm)Small dice – (1/4 inch or 6 mm)Medium dice – (1/2 inch or 12 mm)Large dice – ( ¾ inch or 20 mm)
22 Dec 07 34
22 Dec 07 35