memory mode
DESCRIPTION
MEMORY MODE. The HAAS Control Series. SLIDE LEGEND. PRESS THREE TIMES TO GET TO THIS PAGE (Continued on next slide) Note:. ACTIONS. To advance through the presentation click on your left mouse button or press < ENTER >. To exit press < ESC >. KEYS. INSTRUCTIONS. - PowerPoint PPT PresentationTRANSCRIPT
MEMORY MODE
The HAAS ControlSeries
PRESS
THREE TIMES TO GET TOTHIS PAGE
(Continued onnext slide)
Note:
SLIDE LEGEND
ACTIONS
INSTRUCTIONS
KEYS
INFORMATION
To advance through the presentation
click on your left mouse button
or press <ENTER>.
To exit press <ESC>. OTHER INFORMATION
MEMORY MODEThis module is
intended to provide you with a
familiarizationof the Memory Mode on the Haas Control
Here is where you find the Memory Buttons
Memory Buttons
MEMORY:
SINGLE BLOCK:
DRY RUN:
OPTIONAL STOP:
BLOCK DELETE:
Pressing the memory button on the control will display the current program for running when you press <CYCLE START>.
The current program is the one that has been selected in LIST PROGRAMS.
Memory Button: PROGRAM (MEM) O91002 N00000
MEMORY Button:
The selected program is ready to run.
Press<CYCLE START>
G01 Z-0.0337 F7. ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X0.3058 Y0.5308 ; G01 X0.7835 ; G03 X0.2475 Y0.5508 R0.02 ; F4 FOR PROG REVIEW
O12345 (MILL LAB PROG 1) ;
Single Block Button:
PROGRAM (MEM) O91002 N00000
G01 Z-0.0337 F7. ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X0.3058 Y0.5308 ; G01 X0.7835 ; G03 X0.2475 Y0.5508 R0.02 ; F4 FOR PROG REVIEW
O12345 (MILL LAB PROG 1) ;
SINGLE BLOCK Button:
Used like a toggle switch.
The control will execute one block of program then stop; every press of <CYCLE START> will execute one more
block.
WithSetting 104: Jog
Handle to Single Block ON
Press <CYCLE START>Then rotate the Jog
Handle CCW to run the program. Each click of the handle will execute
1 block.CW = Feed Hold
SINGBK
Excellent for checking out your program when in Graphics Mode
Dry Run Button: PROGRAM (MEM) O91002 N00000
G01 Z-0.0337 F7. ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X0.3058 Y0.5308 ; G01 X0.7835 ; G03 X0.2475 Y0.5508 R0.02 ; DRY RUN SPEED 1.
O12345 (MILL LAB PROG 1) ;
DRYRUN
DRY RUN Button:
Used in Memory or MDI mode.
Used to check a program using reduced
speeds and feeds.
All rapids and feed rates are run at the rate
selected with the JOG speed keys.
Press
Select the speed.
Press<HAND CNTL SPIN>
Adjust with Jog Handle
Optional Stop Button:
PROGRAM (MEM) O91002 N00000
G01 Z-0.0337 F7. ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; M01 G01 X0.7835 (Optional Stop); G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X0.3058 Y0.5308 ; G01 X0.7835 ; G03 X0.2475 Y0.5508 R0.02 ; F4 FOR PROG REVIEW
O12345 (MILL LAB PROG 1) ;
OPTIONAL STOP Button:
When an M01 command is
encountered in the program, then a
program stop will be executed.
Press<CYCLE START>
to continue.
OPTSTP
Block Delete Button:
PROGRAM (MEM) O91002 N00000
G01 Z-0.0337 F7. ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; /G01 X0.7835 (Block Delete) ; G01 X-0.5687 Y-0.9857 ; G01 X-0.2275 ; G01 X0.1314 Y0.2275 ; G01 X-0.7835 ; G01 X0.1314 Y0.2275 ; G01 X0.7835 ; G01 X0.3058 Y0.5308 ; G01 X0.7835 ; G03 X0.2475 Y0.5508 R0.02 ; F4 FOR PROG REVIEW
O12345 (MILL LAB PROG 1) ;
BLKDEL
BLOCK DELETE Button:
When a program block begins with a slash (/) it will be ignored (i.e., that program block will not
execute).
Prepared by Haas AutomationTraining DepartmentOxnard, CA 93030