mechanical data sheet plant item no. shell and tube heat …

MECHANICAL DATA SHEET

SHELL AND TUBE HEAT EXCHANGER

PLANT ITEM No. 24590-BOF-ME-DEP-COND-00001 DATA SHEET No.

Rev.

24590-BOF-MED-DEP-00004 1

of 2

Project RPP-WTP Description DEP Evaporator Primary Condenser

Project No. 24590 Reference Drawings (1) 24590-BOF-ME-DEP-00003001, Rev. 1

Site Hanford Reference Calculations (Internal Use Only)

(2) 24590-BOF-MEC-DEP-00003, Rev. A (3) 24590-BOF-M6C-M80T-00001, Rev. B (4) Deleted

Building 25/Indoors Reference Documents (Internal Use Only)

(5) 24590-WTP-DB-ENG-01-001, Rev. 5 (6) 24590-WTP-Z0C-W13T-00010, Rev. G

General Data (Ref. 2) Quality Level CM TEMA (Class/Type) B ** Seismic Category SC-IV Flow Type (Counter current, etc) Divided Flow Radiation Level Designator (Note 4) R3 Contamination Level Designator C3 Design Code ASME VIII Div 1 Heat Exchanger Duty Btu/hr 5,527,620 Code Stamp Yes Heat Exchanger Area ft2 1674 NB Registration Yes T (LMTD/Corrected LMTD) F 18.4 18.4 Insulation (Note 3) Personnel Protection Not to exceed wet weight lb 23,800 Ambient Room Temp (Min/Max) °F 59 / 104

Thermal/Hydraulic Data (Ref. 2) (Note 7) Shell Side Tube Side

Fluid Name Overhead Vapor

(IN) Condensate

(OUT) Cooling Water

(IN) Cooling Water

(OUT) Fluid Quantities: Total lbm/hr 5409 368508 Condensable Vapor 5350 102 0 Liquid 0 5248 368508 Noncondensable 59 59 0 Normal Temperature F 109 109 84 99 Maximum Temperature F 112 109 84 99 Density lbm/ft3 0.0033 N/A 62.1 Viscosity Cp 0.01 N/A 0.75 Molecular Weight lbm/lbmol 18 18 18 Molecular Weight, Noncondensable lbm/lbmol 29 29 N/A Specific Heat Btu/lbm-F N/A 1.0 1.0 Thermal Conductivity Btu/hr-ft-F N/A N/A 0.36 Latent Heat Btu/lbm @ F 1030.2 N/A N/A Normal Inlet Pressure psig -13.1 (Note 6) 58 (Ref. 3) Max Inlet Pressure psig -12.98 (Note 6) 78 (Ref. 3) Tube side Velocity ft/s N/A 5.9 Pressure Drop (Actual) psi 0.22 14.4 Fouling Resistance (Min) hr-ft2-F/Btu 0.0015 0.0010

Mechanical Design Data Shell Side Tube Side Design Pressure (Max/Min) psig 50 Full vacuum 100 Full vacuum Design Temperature (Max/Min) F 175 40 165 40 Corrosion/Erosion Allowance inch 0.04 0.0

Shell ID inch (Ref. 1) 36

Dimensions (H x D x L (F-F)) ft. (Ref. 1) (Note 8)

7’ 7 3/4”H x 3’D x 18’ 3”L

Total Number of Tubes / Tube Thickness (Nominal) / (Minimum) (Ref. 1) (Ref. 2)

406 / 0.065” / 0.060”

Tube OD / Length (Nominal) (Ref.2)

1.0” / 16’

Tube Pitch / Layout / Clearance (Ref. 2) 1.375 / Triangular / 0.375” No. of Tube Passes

(Ref.2) 6

Issued byRPP-WTP PDC

l - ,__ ====+= I

-

-_J I

I I

I I [_

I--

I -l I - I - -I

I I I--

t--

I I ~

I - I ~

I - I ,__ I

I--

I ~

I I -~ - - -

- -

- - -

I I I _J -

I I I I -

I

-

MECHANICAL:: DATA SHEET . PLANT ITEM No. 24590-BOF-ME-DEP-COND-00001

SHELL AND TUBE HEAT EXCHANGER • DATA SHEET No. Rev. 24590-BOF-MED-DEP-00004 1

Material Data Shell SA 240 304L SS (max carbon 0.030%) Channel/Bonnet SA 240 304L SS (max carbon 0,030%) Plenum Cover SA 240 304L SS (max carbon 0.030%) (Tube-Side) Tube SA 213 304L SML SS (max carbon Head SA 240 304L SS (max carbon 0.030%)

0.030%) Stationary Tube Sheet SA 240 304L SS (max carbon 0.030%) Floating Tube Sheet N/A Shell Side Gaskets N/A Tube Side Gaskets 304L SS Flexitallic CGI Spiral Wound,

PTFE Filler with Inner and Outer Rings Partition Seals * * Baffles/Supports SA 240 304L SS (max carbon 0.030%) Insulation Note 3 Forgings (Shell side) SA 182 F304L SS (max carbon 0.030%) Bolting SA 193 B8 UNS30400 w/ SA-194 GR 8 Forgings (Channel) SA 182 F304L SS (max carbon 0.030%)

Nuts

Construction Data Cross Baffle Type (Ref. 1)** % Baffle Cut (Dia.) (Ref. 1)** Spacing (c/c) inch (Ref. 1)**

Bypass Seal NIA* Longitudinal Seal Type N/A* Expansion Joint Type Annular Rings at Arranoement Distributor Shell* Tube Support Type Flat Plate* U-bend Support Type N/A Weioht of Bundle lb1 5,500* Operatino Weioht lb1 19,200* Full of Water lb1 26,500* Weioht of Shell lb, 4,200*

Notes Seller to fill in data where indicated by double asterisk (**). Data from Seller's proposal indicated with asterisk (*). Seller to confirm all data.

Notes 1. The contents of this document are Dangerous Waste Permit affecting. 2. Please note that source, special nuclear and byproduct materials, as defined in the Atomic Energy Act of 1954 (AEA),

are regulated at the U.S. Department of Energy (DOE) facilities exclusively by DOE acting pursuant to its AEA authority. DOE asserts, that pursuant to the AEA, it has sole and exclusive responsibility and authority to regulate source, special nuclear, and byproduct materials at DOE-owned nuclear facilities. Information contained herein on radionuclides is provided for process description purposes only.

3. DEP-COND-00001 is designed with provisions for 1.5-inch thickness of personnel protection (PP) insulation. The heads are insulated with Mineral Fiber Blanket (Density = 8 lb/ft3), and the shell insulation is Expanded Perlite Block (Density = 13 lb/ft3) . The insulation is provided and installed under an insulation subcontract.

4. This equipment is located in an R3 radiation area (Average Radiation Area), which is designed to have a target radiation level of less than 2.5 mrem/hr (Ref. 5, Table 5-1). The average contact dose rate is 3.75E-04 rad/hr for an equipment life of 21+ years (Ref. 6, Table 8-1).

5. See Ref. 1 for connecting piping sizes and end connections. 6. Ref. 2 gives the normal and maximum pressures to be 1.25 and 1.37 psia. This is converted to psig by subtracting

14.35. 7. All properties shown are given for the maximum temperature (sizing case). The shell-side density and viscosity are

provided at the maximum film temperature of 106°F. 8. The height given is from the bottom of the support leg to the top of Nozzle 1 (Ref. 1 ). The support legs provided will

attach to Bechtel provided supports, which extend from the floor.

A I .oorova Rev Description Originator Checked Reviewed Approved Date

0 Issued for Procurement Holden Carroll Erica Debbie Youssef Mohammad- 12/22/16 Incorporates: Poberezny Adler Zadeh 24590-WTP-EIE-ENG-16-0009

1 Issued for Purchase Erica Holden Carroll Youssef Mohammad-

G/½ Revised to conform to Seller's Poberezny Zadeh Checked vJ

Reviewed ~1 offering and update material Originator ""'1 No Comments fl41 By. Hold•nClrroll-hvcarrol 8y, 0 ..... AdlM • dlacftl,r It descriptions. There are no By: Erica Pobarezny • • poberez 0~ NMI• ' Bedml NalloMI toe: OrgName: MEf Org N11M: S.eht,! N•tion• I. Inc. Plececl: Jun01,2017 lP11cat1: Jun0l . 2017

applicable EIEs. Placid. Jun 01 ,2O17

I

of2