mc40 user guide - pts mobilerevision history changes to the original guide are listed below: change...

MC40 USER GUIDE

April 2014

*MN000111A02*MN000111A02-A

© 2014 Motorola Solutions, Inc. All rights reserved

CopyrightsThe Motorola products described in this document may include copyrighted Motorola computer programs. Laws inthe United States and other countries preserve for Motorola certain exclusive rights for copyrighted computerprograms. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products describedin this document may not be copied or reproduced in any manner without the express written permission of Motorola.© 2014 Motorola Solutions, Inc. All Rights Reserved

No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any languageor computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc.

Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication,estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for thenormal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.

DisclaimerPlease note that certain features, facilities, and capabilities described in this document may not be applicable to orlicensed for use on a particular system, or may be dependent upon the characteristics of a particular mobile subscriberunit or configuration of certain parameters. Please refer to your Motorola contact for further information.

TrademarksMOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registeredtrademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the propertyof their respective owners.

European Union (EU) Waste of Electrical and Electronic Equipment (WEEE)directive

The European Union's WEEE directive requires that products sold into EU countries must have the crossed outtrash bin label on the product (or the package in some cases).

As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countriesshould not dispose of electronic and electrical equipment or accessories in household waste.

Customers or end-users in EU countries should contact their local equipment supplier representative or service centrefor information about the waste collection system in their country.

3 | Copyrights

MN000111A02-A | April 2014 | Send Feedback

http://docsurvey.motorolasolutions.com

Revision HistoryChanges to the original guide are listed below:

Change Date Description

-01 Rev A 08/30/2013 Initial release.

-02 Rev A 04/24/2014 Add RS507 support, Bluetooth pairing utility. Update PTT Express application.

5 | Revision History



Contents

Copyrights........................................................................................................................................ 3Revision History...............................................................................................................................5List of Figures................................................................................................................................ 11List of Tables.................................................................................................................................. 13About This Guide...........................................................................................................................15

Documentation Set.............................................................................................................................................. 15Configurations.....................................................................................................................................................15Chapter Descriptions........................................................................................................................................... 16Notational Conventions.......................................................................................................................................16Icon Conventions.................................................................................................................................................16Related Documents..............................................................................................................................................17Service Information.............................................................................................................................................17

Chapter 1: Getting Started....................................................................................19Features............................................................................................................................................................... 19Unpacking........................................................................................................................................................... 21Setup....................................................................................................................................................................22

Installing the Battery............................................................................................................................... 22Charging the Battery............................................................................................................................... 22Powering On the MC40...........................................................................................................................23Replacing the Battery.............................................................................................................................. 24

Battery Management........................................................................................................................................... 25Setting the Date and Time................................................................................................................................... 26Display Setting.................................................................................................................................................... 27

Setting the Screen Brightness..................................................................................................................27Setting Screen Rotation........................................................................................................................... 27Changing the Screen Timeout Setting.....................................................................................................28

General Sounds Setting....................................................................................................................................... 28

Chapter 2: Using the MC40.................................................................................. 31Home Screen....................................................................................................................................................... 31Status Bar............................................................................................................................................................ 32

Status Icons..............................................................................................................................................32Notification Icons.................................................................................................................................... 34

Managing Notifications.......................................................................................................................................35Application Shortcuts and Widgets.....................................................................................................................35

Adding an Application or Widget to the Home Screen...........................................................................35Moving Items on the Home Screen.........................................................................................................36Removing an App or Widget from the Home Screen............................................................................. 36

Folders.................................................................................................................................................................36Creating Folders...................................................................................................................................... 36Naming Folders....................................................................................................................................... 36Removing a Folder.................................................................................................................................. 37

Home Screen Wallpaper......................................................................................................................................37Change the Home Screen Wallpaper.......................................................................................................37

Using the Touchscreen........................................................................................................................................ 37Using the On-screen Keyboard........................................................................................................................... 38Applications.........................................................................................................................................................39

Contents | 7

Accessing Applications........................................................................................................................... 41Switching Between Recent Applications................................................................................................ 42

Un-Locking the Screen........................................................................................................................................42Single User Mode....................................................................................................................................42MultiUser Mode...................................................................................................................................... 44

MultiUser Login..........................................................................................................................44MultiUser Logout........................................................................................................................45

Resetting the Device............................................................................................................................................45Performing a Soft Reset.......................................................................................................................... 45Performing a Hard Reset......................................................................................................................... 45

Suspend Mode..................................................................................................................................................... 46File Browser........................................................................................................................................................ 46PTT Express Voice Client...................................................................................................................................48

Enabling PTT Communication................................................................................................................49Selecting a Talk Group............................................................................................................................49PTT Communication............................................................................................................................... 49

Creating a Group Call..................................................................................................................50Responding to a Group Broadcast...............................................................................................51Responding with a Private Response.......................................................................................... 51Responding with a Private Response with the Wired Headset................................................... 51

Disabling PTT Express Voice Client Communication............................................................................51VoIP Telephony Ready....................................................................................................................................... 51

Chapter 3: Data Capture.......................................................................................53Imager..................................................................................................................................................................53Digital Camera.................................................................................................................................................... 53RS507 Hands-Free Imager.................................................................................................................................. 54Scanning Considerations..................................................................................................................................... 54Bar Code Capture with Imager............................................................................................................................55Bar Code Capture with Integrated Camera......................................................................................................... 56Bar Code Capture with RS507 Hands-Free Imager............................................................................................ 56

Pairing the RS507 Hands-Fee Imager Using SSI....................................................................................58Pairing the RS507 Hands-Free Imager Bluetooth HID...........................................................................58

Reading Magnetic Stripe Cards...........................................................................................................................59Improper Swiping....................................................................................................................................61

DataWedge.......................................................................................................................................................... 63Enabling DataWedge...............................................................................................................................63Disabling DataWedge..............................................................................................................................64

Chapter 4: WLAN..................................................................................................65Scan and Connect to a Wi-Fi Network................................................................................................................65

Chapter 5: Bluetooth..............................................................................................67Adaptive Frequency Hopping............................................................................................................................. 67Security................................................................................................................................................................67Bluetooth Profiles................................................................................................................................................68Bluetooth Power States....................................................................................................................................... 68Bluetooth Radio Power – Android...................................................................................................................... 68

Enabling Bluetooth..................................................................................................................................69Disabling Bluetooth.................................................................................................................................69

Discovering Bluetooth Device(s)........................................................................................................................ 69Changing the Bluetooth Name............................................................................................................................ 70Connecting to a Bluetooth Device.......................................................................................................................70

8 | Contents

Selecting Profiles on the Bluetooth Device.........................................................................................................71Disconnecting from a Bluetooth Device............................................................................................................. 71Unpairing a Bluetooth Device.............................................................................................................................71

Chapter 6: Photos and Videos...............................................................................73Taking Photos......................................................................................................................................................73Taking a Panoramic Photo.................................................................................................................................. 74Recording Videos................................................................................................................................................75Camera Settings...................................................................................................................................................76Video Settings..................................................................................................................................................... 76Viewing Photos and Videos................................................................................................................................ 77

Working with Albums.............................................................................................................................78Share an Album...........................................................................................................................78Get Album Information............................................................................................................... 78Deleting an Album...................................................................................................................... 79

Working with Photos...............................................................................................................................79Viewing and Browsing Photos....................................................................................................79Rotating a Photo.......................................................................................................................... 80Cropping a Photo.........................................................................................................................80Get Photo Information.................................................................................................................81Share a Photo...............................................................................................................................81Deleting a Photo.......................................................................................................................... 81

Working with Videos.............................................................................................................................. 81Watching Videos......................................................................................................................... 81Sharing a Video...........................................................................................................................82Deleting a Video..........................................................................................................................82

Chapter 7: Accessories...........................................................................................83MC40 Accessories...............................................................................................................................................83Micro USB Cable................................................................................................................................................ 84Single Slot Charge Cradle................................................................................................................................... 85Five Slot Charge Only Cradle............................................................................................................................. 86Four Slot Battery Charger................................................................................................................................... 88

Chapter 8: Maintenance and Troubleshooting................................................... 91Maintaining the MC40........................................................................................................................................ 91Battery Safety Guidelines....................................................................................................................................91Cleaning Instructions...........................................................................................................................................92Cleaning the MC40............................................................................................................................................. 93

Connector Cleaning.................................................................................................................................93Cleaning Cradle Connectors................................................................................................................................93Troubleshooting the MC40................................................................................................................................. 94Single-Slot Charge Cradle Troubleshooting....................................................................................................... 96Five-Slot Charge Only Cradle CRDUNIV-40–5000R Troubleshooting............................................................ 96Four-Slot Battery Charger SACMC40XX-4000R Troubleshooting...................................................................97

Chapter 9: Technical Specifications..................................................................... 99MC40 Technical Specifications.......................................................................................................................... 99Single-Slot Charge Cradle CRDMC40XX-1000R Technical Specifications................................................... 102Five-Slot Charge Only Cradle CRDUNIV-40-5000R Technical Specifications..............................................102Four-Slot Battery Charger SACMC40XX-4000R Technical Specifications....................................................103

Contents | 9

10 | Contents

List of Figures

Figure 1: Manufacturing Label Location ........................................................................................17Figure 2: Front View ...................................................................................................................... 19Figure 3: Back View .......................................................................................................................21Figure 4: Inserting the Battery ........................................................................................................22Figure 5: Lift Battery Latch ............................................................................................................24Figure 6: Remove Battery ...............................................................................................................24Figure 7: Battery Use Screen ..........................................................................................................25Figure 8: Low Battery Notification Screen .....................................................................................26Figure 9: Brightness Dialog Box .................................................................................................... 27Figure 10: Sounds Screen ............................................................................................................... 28Figure 11: Volumes Dialog Box .....................................................................................................29Figure 12: Home Screen ................................................................................................................. 31Figure 13: Notification and Status Icons ........................................................................................ 32Figure 14: Notification Panel ..........................................................................................................35Figure 15: Stacked Shortcut Icons ..................................................................................................36Figure 16: Unnamed Folder ............................................................................................................36Figure 17: Open Folder ...................................................................................................................37Figure 18: Renamed Folder ............................................................................................................ 37Figure 19: APPS Window .............................................................................................................. 41Figure 20: Recently Used Applications ..........................................................................................42Figure 21: Lock Screen ...................................................................................................................43Figure 22: PIN Screen .................................................................................................................... 43Figure 23: Pattern Screen ................................................................................................................44Figure 24: Password Screen ............................................................................................................44Figure 25: Multiple User Log In Screen .........................................................................................45Figure 26: Lock Screen ...................................................................................................................46Figure 27: File Browser Screen ...................................................................................................... 47Figure 28: PTT Express Default User Interface ............................................................................. 48Figure 29: PTT Express Window ................................................................................................... 49Figure 30: MC40 PTT Buttons ....................................................................................................... 50Figure 31: Wired Headset ...............................................................................................................50Figure 32: RS507 Hands-Free Imager ............................................................................................54

List of Figures | 11

Figure 33: Bar Code Scanning ........................................................................................................55Figure 34: Aiming Pattern .............................................................................................................. 55Figure 35: Pick List Mode with Multiple Bar Codes in Aiming Pattern ........................................55Figure 36: Application with Preview Window ...............................................................................56Figure 37: Bar Code Scanning with RS507 ....................................................................................57Figure 38: Aiming Pattern .............................................................................................................. 57Figure 39: Pick List Mode with Multiple Bar Codes in Aiming Pattern ........................................57Figure 40: Bluetooth Pairing Utility ............................................................................................... 58Figure 41: RS507 Bluetooth HID Bar Code ...................................................................................59Figure 42: Swiping a Magnetic Stripe Card ................................................................................... 60Figure 43: Do Not Start Swipe in Middle of Card ..........................................................................61Figure 44: Avoid Thumb Hitting Device ........................................................................................62Figure 45: Do Not Hold End of Card While Swiping .................................................................... 62Figure 46: Do Not Swipe Card on Angle ....................................................................................... 63Figure 47: Wi-Fi Screen ................................................................................................................. 66Figure 48: Bluetooth Pairing - Enter PIN ....................................................................................... 69Figure 49: Bluetooth Pairing — Simple Pairing .............................................................................70Figure 50: Camera Mode ................................................................................................................ 73Figure 51: Panoramic Mode ........................................................................................................... 74Figure 52: Video Mode ...................................................................................................................75Figure 53: Gallery — Albums ........................................................................................................ 77Figure 54: Photos Inside an Album ................................................................................................ 78Figure 55: Photo Example .............................................................................................................. 79Figure 56: Cropping Tool ............................................................................................................... 80Figure 57: Video Example ..............................................................................................................82Figure 58: Charging Using the Micro USB Cable ..........................................................................85Figure 59: Communication Using the Micro USB Cable ...............................................................85Figure 60: MC40 Battery Charging ................................................................................................86Figure 61: Charging MC40s and Spare Batteries ........................................................................... 87Figure 62: Four Slot Battery Charger ............................................................................................. 88

12 | List of Figures

List of Tables

Table 1: Features - Front View .......................................................................................................19Table 2: Features - Back View ....................................................................................................... 21Table 3: Battery Charge LED Status .............................................................................................. 23Table 4: Home Screen Items ...........................................................................................................32Table 5: Status Icons .......................................................................................................................32Table 6: Notification Icons ............................................................................................................. 34Table 7: Applications ......................................................................................................................39Table 8: PTT Express Default user Interface Descriptions ............................................................ 49Table 9: MC40 Accessories ............................................................................................................83Table 10: Spare Battery Charge LED Status .................................................................................. 89Table 11: Troubleshooting the MC40 .............................................................................................94Table 12: Troubleshooting the Single-slot Charge Cradle ............................................................. 96Table 13: Troubleshooting the Five-Slot Charge Only Cradle .......................................................96Table 14: Troubleshooting the Four-slot Battery Charger ..............................................................97Table 15: MC40 Technical Specifications ......................................................................................99Table 16: Single-slot Charge Cradle Technical Specifications .................................................... 102Table 17: Five-Slot Charge Only Cradle Technical Specifications ..............................................102Table 18: Four-slot Battery Charger Technical Specifications .................................................... 103

List of Tables | 13

14 | List of Tables

About This GuideThis guide provides information on using the MC40 and accessories.

Note: Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the MC40 provides information for specific user needs, and includes:

• MC40 Quick Start Guide - describes how to get the device up and running.• MC40 Regulatory Guide - provides required regulatory information.• MC40 User Guide - describes how to use the device.• MC40 Integrator Guide - describes how to set up the device and accessories.

Configurations

This guide covers the following configurations:

Configuration Radios Display Memory Data CaptureOptions

Operating Sys-tem

MC40 WLAN:802.11a/b/g/n/r

WPAN: Blue-tooth v2.1 withEDR

4.3” colorWVGA

1 GB RAM / 8GB Flash

camera and im-ager or camera,imager and MSR,optional RS507Hands-free Im-ager

Android-based,Android Open-Source Project4.1.1

Software Versions

To determine the current software versions touch > About device.

• Serial number – Displays the serial number.• Model number – Displays the model number.• Android version – Displays the operating system version.• Kernel version – Displays the kernel version number.• Build number – Displays the software build number.

The build number contains the software revision number and whether the MC40 is VoIP telephony ready.

Example Build Number: 0z-4AJ11–J-xxxx–xxxx–y0–M1–mmddyy

• z = software version number• y = VoIP telephone ready

where:

• 0 = not VoIP telephony ready• V = VoIP telephony ready.• F = FIPS & VoIP telephony ready.

15 | About This Guide



Chapter Descriptions

Topics covered in this guide are as follows:

• Getting Started on page 19 provides information on getting the MC40 up and running for the first time.• Using the MC40 on page 31 provides basic instructions for using the MC40, including powering on and

resetting the MC40.• Data Capture on page 53 provides information for capturing bar code data using the internal camera and

optional scan modules and Bluetooth scanner.• WLAN on page 65 provides information for configuring Wi-Fi.• Bluetooth on page 67 provides information for configuring Bluetooth.• Photos and Videos on page 73 explains how to take photos, capture videos and video images in the Gallery

application.• Accessories on page 83 describes the available accessories and how to use them with the MC40.• Maintenance and Troubleshooting on page 91 includes instructions on cleaning and storing the MC40, and

provides troubleshooting solutions for potential problems during MC40 operation.• Technical Specifications on page 99 provides the technical specifications for the MC40.

Notational Conventions

The following conventions are used in this document:

• Italics are used to highlight the following:

- Chapters and sections in this and related documents- Icons on a screen.

• Bold text is used to highlight the following:

- Dialog box, window, and screen names- Drop-down list and list box names- Check box and radio button names- Button names on a screen.

• Bullets (•) indicate:

- Action items- Lists of alternatives- Lists of required steps that are not necessarily sequential

• Sequential lists (for example, lists that describe step-by-step procedures) appear as numbered lists.

Icon Conventions

The documentation set is designed to give the reader more visual clues. The following graphic icons are usedthroughout the documentation set. These icons and their associated meanings are described below.

Warning: The word WARNING with the associated safety icon implies information that, if disregarded,could result in death or serious injury, or serious product damage.

Caution: The word CAUTION with the associated safety icon implies information that, if disregarded,may result in minor or moderate injury, or serious product damage.


Send Feedback | April 2014 | MN000111A02-A


Note: NOTE contains information more important than the surrounding text, such as exceptions orpreconditions. They also refer the reader elsewhere for additional information, remind the reader how tocomplete an action (when it is not part of the current procedure, for instance), or tell the reader wheresomething is located on the screen. There is no warning level associated with a note.

Related Documents

• MC40 Quick Start Guide, p/n 72-166941-xx• MC40 Regulatory Guide, p/n 72-166942-xx• MC40 Integrator Guide, p/n 72E-166943-xx• RS507 Hands-free Imager Product Reference Guide, p/n 72E-120802–xx

For the latest version of this guide and all guides, go to: http://www.motorolasolutions.com/support

Service Information

If you have a problem with your equipment, contact Motorola Solutions Global Customer Support Center for yourregion. Contact information is available at: http://www.motorolasolutions.com/support.

When contacting Motorola Solutions Global Customer Support Center, please have the following informationavailable:

• Serial number of the unit (found on manufacturing label)• Model number or product name (found on manufacturing label)• Software type and version number

Figure 1: Manufacturing Label Location

About This Guide | 17


http://www.motorolasolutions.com/support

http://www.motorolasolutions.com/support


Motorola responds to calls by email or telephone within the time limits set forth in support agreements.

If your problem cannot be solved by Motorola Solutions Global Customer Support Center, you may need to returnyour equipment for servicing and will be given specific directions. Motorola is not responsible for any damagesincurred during shipment if the approved shipping container is not used. Shipping the units improperly can possiblyvoid the warranty.

If you purchased your product from a Motorola business partner, contact that business partner for support.




Chapter

1Getting Started

This chapter provides the features of the MC40 and explains how to set it up for the first time.

Features

Figure 2: Front View

23

4117

16 5

6

7

8

910

111

12

13

14

15

Table 1: Features - Front View

Number Item Function

1 Microphone Use for making voice recordings.

2 Receiver Provide audio in handset mode.

3 Light/ProximitySensor

Determines ambient light for controlling display backlight intensity andfor turning off display when in handset mode.

Table continued…

19 | Getting Started




4 Right LED Indicates battery charge state when MC40 is in a charger.

Indicates decode functionality. Lights green indicating a successful de-code.

5 Touch Screen Displays all information needed to operate the MC40.

6 Menu Button - Opens a menu with items that affect the current screen orapplication.

7 Search - Opens the Search window.

8 Speaker Provides audio output for video and music playback.

9 USB Connector Provides power to the device from cradles and cables and provides USBclient and host communications.

10 Charging Contacts Provides power to the MC40 from the cradles.

11 Headset Jack Connects to mono headsets (3-wire, 2.5 mm plug).

12 Back Button — Displays the previous screen. Closes the keyboard if theon-screen keyboard is open.

13 Home Button — Displays the Home screen with a single touch. Displaysrecently used applications when held for a short period.

14 Left Scan/ActionButton

Initiates scanning when a scan application is enabled (default). Program-mable using Button Remap Program. See MC40 Integrator Guide for moreinformation.

15 PTT Button Initiates a Broadcast PTT call when PTT Express is active. Programmableusing Button Remap Program. See MC40 Integrator Guide for more infor-mation.

16 Power Button Press and hold to turn on the MC40. Press to turn on or off the screen.Press and hold to select one of these options:

• Silent mode - The device is set to vibrate mode; all sounds are disa-bled except for alarms.

• Airplane mode - Disable all wireless connections.

• Disable Touch Keys - Disables or enables the four touch keys belowthe screen.

• Battery swap - Place device in Battery Swap mode when replacing thebattery.

• Reset - Reboot the MC40 when software stops responding.

• Power off - Turn off the MC40.

17 Left LED Indicates decode functionality. Lights green indicating a successful de-code.




Figure 3: Back View

1819

20

21

2223

24

25

Table 2: Features - Back View


18 Battery Provides the MC40 with operating power.

19 Battery Latch Secures the battery in position.

20 Camera Takes photos, videos, and captures bar code data.

21 Right Scan/ActionButton

Initiates scanning when a scan application is enabled (default). Program-mable using Button Remap Program. See MC40 Integrator Guide for moreinformation.

22 Volume Control Increases and decrease audio volume. Programmable using Button RemapProgram. See MC40 Integrator Guide for more information.

23 Imager Captures bar code data.

24 MSR Slot (Option-al)

Use to swipe magnetic stripe cards during credit or debit transactions.

25 Finger Strap Plug Covers mounting area for optional Finger Strap.

Unpacking

Carefully remove all protective material from the MC40 and save the shipping container for later storage andshipping.

Verify the following items are in the box:

• MC40• Lithium-ion battery• Quick Start Guide• Regulatory Guide.

Getting Started | 21



Inspect the equipment for damage. If any equipment is missing or damaged, contact the Motorola Solutions GlobalCustomer Support Center immediately. See Service Information on page 17 for contact information.

Setup

To start using the MC40 for the first time:

• Install the battery• Charge the MC40• Power on the MC40.

Installing the BatteryTo install the battery:

Procedure:

1 Align the battery with the slots in the battery compartment.

Figure 4: Inserting the Battery

2 Lower the battery and press down until it snaps into place.3 Press down on the battery latch.4 Press the Power button to turn on the MC40.

Charging the BatteryCaution: Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines onpage 91.

Before using the MC40 for the first time, charge the main battery until the Right light emitting diode (LED) turnssolid green (see Table 3: Battery Charge LED Status on page 23 for charge status indications). To charge theMC40, use a cable or a cradle with the appropriate power supply. For information about the accessories available forthe MC40, see Accessories on page 83.

The MC40 is equipped with a memory backup battery that automatically charges from the fully-charged main battery.When using the MC40 for the first time, the backup battery requires approximately 36 hours to fully charge. This isalso true any time the backup battery is discharged, which occurs when the main battery is removed for several hours.The backup battery retains random access memory (RAM) data in memory for at least 10 minutes (at roomtemperature) when the MC40’s main battery is removed, when Battery Swap feature is used. When the MC40 reaches




a very low battery state, the combination of main battery and backup battery retains RAM data in memory for at least48 hours.

For cable and cradle setup and charging procedures refer to the MC40 Integrator Guide.

• Micro USB Cable• Single Slot Charging Cradle• Five Slot Charge Only Cradle.

Table 3: Battery Charge LED Status

Status Indications

Off MC40 is not charging.

MC40 is not inserted correctly in the cradle.

MC40 is not connected to a power source.

Charger or cradle is not powered.

Slow Blinking Amber (3 blinks ev-ery 2 seconds)

MC40 is charging.

Solid Green Charging complete.

Fast Blinking Amber (3 blinks/second)

Charging error, e.g.:

• Temperature is too low or too high.• Charging has gone on too long without completion (typically eight hours).

Flashes Amber once (when Powerbutton pressed)

Critical battery state. Battery too low to boot device.

Fast Blinking Amber (when Powerbutton pressed)

Battery over-temperature condition. Device shuts down. Battery will notcharge until temperature returns to normal operating value.

Charging TemperatureCharge batteries in ambient temperatures from 0 °C to 40 °C (32 °F to 104 °F) or up to 45 °C (113 °F) as reported by

the battery. To view the battery temperature, touch > About device > Battery Information.

Note that charging is intelligently controlled by the MC40. To accomplish this, for small periods of time, the MC40or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. TheMC40 or accessory indicates when charging is disabled due to abnormal temperatures via its LED.

Charging Spare BatteriesSee Accessories on page 83 for information on using accessories to charge spare batteries.

Powering On the MC40If the MC40 did not turn on when the battery was installed, press the Power button until the Right and Left LEDsflash once. The splash screen displays for about a minute as the MC40 initializes its flash file system. Note that thesewindows also appear upon reset.




Replacing the BatteryNote: Ensure that the Battery Swap mode procedures are followed, otherwise the backup battery willdeplete quickly.

Procedure:

1 Press the Power button until the menu displays.2 Touch Battery swap. The Right and Left LEDs light red.3 Wait until the LEDs turns off.4 Lift the battery latch.

Figure 5: Lift Battery Latch

5 Remove the battery out of the battery compartment.

Figure 6: Remove Battery

6 Align the replacement battery in the battery compartment.7 Lower the battery and press down until it snaps into place.8 Press down on the battery latch.9 Press the Power button to turn on the MC40.




Battery Management

Note:

Prior to checking the battery charge level, remove the MC40 from any AC power source (cradle or cable).

To check the charge status of the main battery, touch > About device > Status.

Battery status indicates that the battery is discharging and Battery level lists the battery charge (as a percentage offully charged).

Monitor Battery UsageThe Battery Use screen lists which applications consume the most battery power. Also use it to turn off applicationsthat were downloaded if they are consuming too much power.

Touch > Battery.

Figure 7: Battery Use Screen

The Battery Use screen lists the applications using the battery. The discharge graph at the top of the screen shows therate of battery discharge since last charged (short periods of time when connected to a charger are shown as thin greenlines at the bottom of the chart), and how long it has been running on battery power.

Touch an application in the Battery Use screen to display details about its power consumption. Different applicationsdisplay different information. Some applications include buttons that open screens with settings to adjust power use.

Low Battery NotificationWhen the battery charge drops below 20%, the MC40 sounds an alert and displays a notice to connect the MC40 topower.




Figure 8: Low Battery Notification Screen

The user should replace the battery or charge the MC40 using one of the charging accessories.

When the battery charge drops below 15%, the MC40 sounds an alert and displays a notice to connect the MC40 topower.

When the battery charge drops below 12%, the MC40 sounds an alert and screen turns off. The Right and Left LEDslight red while goes into critical suspend mode to save data. Once it reaches critical suspend the Right and Left LEDsturn off.

The user must replace the battery or charge the MC40 using one of the charging accessories to retain data.

Battery OptimizationObserve the following battery saving tips:

• Leave the MC40 connected to AC power at all times when not in use.• Set the screen to turn off after a short period of non-use.• Reduce the screen brightness.• Turn off all wireless radios when not in use.• Turn off automatic syncing for Email, Calendar, Contacts, and other applications.• Use the Power Control widget to check and control the status of radios, the screen brightness, and syncing.• Minimize use of applications that keep the MC40 from suspending, for example, music and video applications.

Setting the Date and Time

The date and time is automatically synchronized using an NTP server when the MC40 is connected to a wirelessnetwork. The user is only required to set the time zone or set the date and time when not connected to a wirelessnetwork.

Procedure:

1 Touch .2 Touch Date & time.3 Touch Automatic date & time to disable automatic date and time synchronization.4 Touch Automatic time zone to disable automatic time zone synchronization.5 Touch Set date.6 Move the sliders up and down to select the month, date and year.7 Touch Done.8 Touch Set time.9 Move the sliders up and down to select the hour, minutes and part of the day.10 Touch Done.11 Touch Select time zone.12 Select the current time zone from the list.




13 Touch .

Display Setting

Use Display settings to change the screen brightness, change the background image, enable screen rotation, set sleeptime and change font size.

Setting the Screen BrightnessProcedure:

1 Touch .2 Touch Display.3 Touch Brightness.

Figure 9: Brightness Dialog Box

4 In the Brightness dialog box, check the Automatic brightness checkbox to set the device to automatically adjustthe brightness using the built-in light sensor. Uncheck the checkbox to set the brightness manually. Use the sliderto set a brightness level.

5 Use the slider to set a brightness level.6 Touch OK.7 Touch .

Setting Screen RotationThe user can set the MC40 screen to rotate 90 degrees left or right.

Procedure:

1 Touch .2 Touch Display.3 In the Display settings screen, check Auto-rotate screen to set the MC40 to automatically switch orientation

when the MC40 is rotated.4 Touch .




Changing the Screen Timeout SettingTo set the MC40 to turn off after a short period of non-use:

Procedure:

1 Touch .2 Touch Display3 Touch Sleep4 Select a value from the Sleep window. Options:

• 15 seconds• 30 seconds• 1 minute (default)• 2 minutes• 5 minutes• 10 minutes• 30 minutes

5 Touch .

General Sounds Setting

Use the Sounds settings to configure media and alarm volumes. Touch > Sounds.

Figure 10: Sounds Screen

• Volumes - Use to change the volume of media, ringtones and notifications and alarms.




Figure 11: Volumes Dialog Box

• Call Ringtone and Vibrate

- Phone ringtone - Opens a dialog box to select the ringtone to sound when a VoIP call is received (VoIPtelephony ready only).

- Vibrate when ringing - Check to make the device vibrate when a call is received (VoIP telephony readyonly).

• System

- Default notification - Touch to select a sound to play for all system notifications.- Touch sounds - Check to play a sound when making screen selection.- Screen lock sounds - Check to play a sound when locking and unlocking the screen.- Vibrate on touch - Check to have the device vibrate when touching soft keys and on certain screen

interactions.




Chapter

2Using the MC40

This chapter describes the screens, status and notification icons, and controls on the MC40, and provides basicinstructions for using the MC40.

Home Screen

The Home screen displays when the MC40 turns on. Depending upon the configuration, the Home screen mightappear different. Contact your system administrator for more information.

After a suspend or screen time-out, the Home screen displays with the lock sliders. Slide to the right toward to unlock the screen. For screen locking information see Un-Locking the Screen on page 42.

Figure 12: Home Screen

The Home screen consists of the following:

31 | Using the MC40



Table 4: Home Screen Items

Item Description

1 — Status Bar Displays the time, status icons (right side), and notification icons (left side). For more informa-tion see Status Icons on page 32 and Managing Notifications on page 35.

2 — Browser Icon Opens the Browser application.

3 — All Apps Icon Opens the APPS window.

4 — Settings Icon Opens the Settings window.

5 — Shortcut Icons Opens applications installed on the MC40. See Application Shortcuts and Widgets on page35 for more information.

6 — Widgets Launches stand-alone applications that run on the Home screen. See Application Shortcuts andWidgets on page 35 for more information.

The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left orright to view the additional screens.

Status Bar

The Status bar displays the time, notification icons (left side) and status icons (right side).

Figure 13: Notification and Status Icons

1 Notifications icons

2 Status icons

If there are more notifications than can fit in the Status bar, displays indicating that more notifications exist. Openthe Notifications panel to view all notifications and status.

Status IconsTable 5: Status Icons

Icon Description

Indicates that Bluetooth is on.

Indicates that the device is connected to another Bluetooth device.

Table continued…

32 | Using the MC40



Icon Description

Indicates that the Alarm is active.

Indicates that all sounds except media and alarms are silenced and vibrate mode is active.

Indicates that the audio is silenced.

Connected to a Wi-Fi network. Excellent signal strength.

Connected to a Wi-Fi network. Good signal strength.

Connected to a Wi-Fi network. Fair signal strength.

Connected to a Wi-Fi network. Poor signal strength.

No Wi-Fi signal.

Indicates that the battery charge is very low.

Indicates that the battery charge is low.

Indicates that the battery is partially drained.

Indicates that the battery is fully charged.

Indicates that the battery is charging.

Indicates that the MC40 is calculating the battery capacity level.

Indicates an unknown charging error.

Indicates that the battery temperature is nearing the high for charging to occur.

Indicates that the battery temperature is nearing the low for charging to occur.

Indicates that the Airplane Mode is active. All radios are turned off.

Indicates that a wired headset is connected to the MC40.

Using the MC40 | 33



Notification IconsTable 6: Notification Icons

Icon Description

Indicates that more notifications are available for viewing.

Indicates that data is syncing.

Indicates an upcoming event.

Indicates that an open Wi-Fi network is available.

Indicates that a song is playing.

Indicates that a problem with sign-in or sync has occurred.

Indicates that the device is uploading data.

Indicates that the Internal Storage is almost full.

Indicates that the device is downloading data when animated and download is complete when stat-ic.

Indicates that the device is connected via USB cable.

Indicates that the device is connected to a virtual private network (VPN).

Preparing Internal Storage.

Indicates that USB debugging is enabled on the device.

Screenshot captured.

Error capturing screenshot.

Indicates that the MultiUser feature is enabled.

Indicates that a new user is logging in.

Indicates the status of the PTT Express Voice Client.

34 | Using the MC40



Managing Notifications

Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events. When anotification occurs, an icon appears in the Status bar with a brief description. See Notification Icons on page 34 for alist of possible notification icons and their description. Open the Notifications panel to view a list of all thenotifications.

To open the Notification panel, drag the Status bar down from the top of the screen.

Figure 14: Notification Panel

To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel closesand the subsequent activity is dependent on the notification.

To clear all notifications, open the Notifications Panel and then touch . All event-based notifications are removed.Ongoing notifications remain in the list.

To close the Notification Panel, drag the bottom of the Notifications Panel to the top of the screen or touch .

Application Shortcuts and Widgets

Application shortcuts placed on the Home screen allow quick and easy access to applications. Widgets are self-contained applications placed on the Home screen to access frequently used features.

Adding an Application or Widget to the Home ScreenProcedure:

1 Go to the desired Home screen.2 Touch .3 Swipe right, if necessary, to find the application icon or widget.4 Touch and hold the icon or widget until the Home screen appears.5 Position the icon on the screen and then release.

Using the MC40 | 35



Moving Items on the Home ScreenProcedure:

1 Touch and hold the item until it floats on the screen.2 Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home screen.3 Lift finger to place the item on the Home screen.

Removing an App or Widget from the Home ScreenProcedure:

1 Go to the desired Home screen.2 Touch and hold the application shortcut or widget icon until it floats on the screen.3 Drag the icon to on the top of the screen and then release.

Folders

Use Folders to organize similar applications together. Touch the folder to open and display items in the folder.

Creating FoldersProcedure:

1 Go to the desired Home screen.2 Place at least two application shortcuts on the Home screen.3 Touch and hold a shortcut until it floats on the screen.4 Move the icon over another icon. A blue circle appears around the icons.

Figure 15: Stacked Shortcut Icons

5 Lift finger to stack the icons. The shortcut icons appear over a black circle.

Figure 16: Unnamed Folder

Naming FoldersProcedure:

1 Touch the folder.

36 | Using the MC40



Figure 17: Open Folder

2 Touch the title area and enter a folder name using the keyboard.3 Touch Done.4 Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.

Figure 18: Renamed Folder

Removing a FolderProcedure:

1 Touch and hold the folder icon until it enlarges and the device vibrates.2 Drag the icon to and release.

Home Screen Wallpaper

Note: Use of Live Wallpaper may reduce battery life.

Change the Home Screen WallpaperProcedure:

1 Touch and hold on the Home screen until the Choose Wallpaper from menu appears.2 Touch Gallery, Live wallpapers or Wallpapers.

• Gallery - Select to use an image stored on the device.• Live wallpapers - Select to use an animated wallpaper image.• Wallpapers - Select to use a wallpaper image.

3 Touch Save or Set wallpaper.

Using the Touchscreen

Use the dual-touch sensitive screen to operate the device.

• Touch - Touch to:

- select items on the screen- type letters and symbols using the on-screen keyboard- press on-screen buttons.

Using the MC40 | 37



• Touch and Hold - Touch and hold:

- an item on the Home screen to move it to a new location or to the trash.- an item in the All Apps screen to create a shortcut on the Home screen.- the Home screen to change the Home screen wallpaper.

• Drag - Touch and hold an item for a moment and then move finger on the screen until reaching the new position.

• Swipe - Move finger up and down or left and right on the screen to:

- unlock the screen

- view additional Home screens

- view additional application icons in the All Apps screen

- view more information on an application’s screen.

• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.

• Pinch - In some applications, zoom in and out by placing two fingers on the screen and pinching them together (tozoom out) or spreading them apart (to zoom in).

Using the On-screen Keyboard

Use the on-screen keyboard to enter text in a text field. To configure the keyboard settings, touch > and thenselect Android keyboard settings.

Editing TextEdit entered text and use menu commands to cut, copy, and paste text within or across applications. Someapplications do not support editing some or all of the text they display; others may offer their own way to select text.

Entering Numbers, Symbols and Special CharactersTo enter numbers and symbols:

• Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate charactersdisplay an ellipsis ( ... ) below the character.

• Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them, and thenlift both fingers to return to the lowercase keyboard.

• Touch to switch to the numbers and symbols keyboard.•

Touch the key on the numbers and symbols keyboard to view additional symbols.

To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.

• A larger version of the key displays briefly over the keyboard.• Keys with alternate characters display an ellipsis ( ... ) below the character.

38 | Using the MC40



Applications

The All Apps screen displays icons for all installed applications. Table 7: Applications on page 39 lists theapplications available on the MC40. Refer to the MC40 Integrator Guide for information on installing anduninstalling application.

Table 7: Applications

Icon Description

Bluetooth Pairing Utility – Use to pair Bluetooth devices with the MC40 by scanning a bar code.

Browser - Use to access the Internet or intranet.

Calculator - Provides the basic and scientific arithmetic functions.

Calendar - Use to manage events and appointments.

Camera - Take photos or record videos. For more information see Photos and Videos on page73.

Card Swipe Tutorial - Use to practice swiping a magnetic stripe card through the MSR on devi-ces with an MSR slot.

Clock - Use to schedule alarms for appointments or as a wake-up.

DataWedge - Enables data capture using the camera or optional scanner.

Device-Config - Use to configure multiple MC40 devices. See the MC40 Integrator Guide formore information.

Downloads - Lists all downloads files.

Table continued…

Using the MC40 | 39



Icon Description

DWDemo - Provides a way to demonstrate the data capture features using the Camera, ScanningModule or Magnetic Stripe Reader.

Email - Use to send and receive email.

File Browser - Organize and manage files on the device. See File Browser on page 46 for moreinformation.

Gallery - Use to view photos stored in Internal Storage. See Viewing Photos and Videos on page77 for more information.

MC40 User Guide - Displays the On-device User Guide.

MLog Manager – Use to capture log files for diagnostics. See MC40 Integrator Guide for moreinformation.

MSP Agent - Enables management of the device from an MSP server. Requires the purchase ofan appropriate MSP client license per device to suit the level of management functionality re-quired.

Music - Play music stored in Internal Storage.

People - Use to manage contact information.

Phone - use to dial a phone number when used with some VoIP clients (VoIP telephony readyonly).

PTT Express - Use to launch the PTT Express client for Voice over IP (VoIP) communication.

Rapid Deployment - Allows the device to stage a device for initial use by initiating the deploy-ment of settings, firmware and software. Requires the purchase of an MSP client license per de-vice.

RxLogger – Use to diagnose device and application issues. See MC40 Integrator Guide for moreinformation.

Table continued…

40 | Using the MC40



Icon Description

Search - Use the Google search engine to search the Internet and the device.

Settings - Use to configure the device. For more information, refer to the MC40 Enterprise TabletIntegrator Guide.

Sound Recorder - Use to record audio.

AppLock Administrator - Use to configure the Application Lock feature. This icon appears afterthe optional application is installed.

MultiUser Administrator - Use to configure the MultiUser feature. This icon appears after theoptional application is installed.

Secure Storage Administrator - Use to configure the Secure Storage feature. This icon appearsafter the optional application is installed.

Accessing ApplicationsAll applications installed on the device are accessed using the APPS window.

Procedure:

1 On the Home screen touch . The APPS window displays.

Figure 19: APPS Window

2 Slide the APPS window left or right to view more application icons. Touch an icon to open the application.

Using the MC40 | 41



Note: See Application Shortcuts and Widgets on page 35 for information on creating a shortcut on theHome screen.

Switching Between Recent ApplicationsProcedure:

1 Touch and hold . A window appears on the screen with icons of recently used applications.

Figure 20: Recently Used Applications

2 Slide the window up and down to view all recently used applications.3 Swipe left or right to remove application from the list and force close the application.4 Touch an icon to open it or touch to return to the current screen.

Un-Locking the Screen

Use the Lock screen to protect access to data on the MC40. Some email account require locking the screen. Refer tothe MC40 Integrator Guide for information on setting up the locking feature. The Locking feature functionsdifferently in Single User mode or Multiple User mode.

Single User ModeWhen locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the screen.The device also locks after a pre-defined time-out.

Press and release the Power button to wake the device.

The Lock screen displays. Slide up to unlock the screen. If the Pattern screen unlock feature is enabled, thePattern screen appears instead of the Lock screen.

If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.

42 | Using the MC40



Figure 21: Lock Screen

Figure 22: PIN Screen

Using the MC40 | 43



Figure 23: Pattern Screen

Figure 24: Password Screen

MultiUser ModeWith MultiUser login, multiple users can log on to the device with each user having access to various applicationsand features. When enabled, the Login screen appears after powering on, resetting or after the device wakes fromsuspend mode.

MultiUser LoginProcedure:

1 In the Login text field, enter the username.

44 | Using the MC40



Figure 25: Multiple User Log In Screen

2 In the Password text field, enter the password.3 Touch OK. After a resume from suspend, the user must enter the password.

MultiUser LogoutProcedure:

1 Drag the Status Bar down from the top of the screen.2 Touch MultiUser is active.3 Touch Logout.4 The Login screen appears.

Resetting the Device

There are two reset functions, soft reset and hard reset.

Performing a Soft ResetPerform a soft reset if applications stop responding.

Procedure:

1 Press and hold the Power button until the menu appears.2 Touch Reset.3 The device shuts down and then reboots.4 The device reboots.

Performing a Hard ResetPerform a Hard Reset if the device stops responding. To perform a Hard Reset:

Procedure:

1 Simultaneously press the Power, Left Scan/Action and Up Volume buttons.

Using the MC40 | 45



2 The device shuts down and then reboots.

Suspend Mode

The MC40 goes into suspend mode when the user presses the Power button or after a period of inactivity (set in theDisplay settings window).

To wake the MC40 from Suspend mode, press the Power button.

The Lock screen displays. Slide to the right toward to unlock the screen. If the Pattern screen unlock featureis enabled, the Pattern screen appears instead of the Lock screen. See Un-Locking the Screen on page 42.

Note:

If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds beforetrying again.

If the user forgets the PIN, password or pattern contact the system administrator.

Figure 26: Lock Screen

File Browser

Use the File Browser application to view and mange files on the device.

To open File Browser, touch > .

46 | Using the MC40



Figure 27: File Browser Screen

The address bar (1) indicates the current folder path. Touch the current folder path to manually enter a path and foldername.

Use (2) to select multiple files/folder.

Use (3) to view the internal storage root folder.

Use (4) to view the microSD card root folder.

Use (5) to view the previous folder or to exit the application.

Touch and hold an item to perform an operation on that item. Select one of the options from the File Operationsmenu:

• Information - View detailed information about the file or folder.• Move - Move the file or folder to a new location.• Copy - Copy the select file.• Delete - Delete the selected file.• Rename - Rename the select file.• Open as - Open the selected file as a specific file type.• Share - Share the file with other devices.

Touch to open additional functionality:

• Touch > New Folder to create a new folder in the current folder.• Touch > Search to search for a file or folder.• Touch > Sort to sort the list by name, by type, by size or by date.• Touch > Refresh to re-display the contents of the current folder.• Touch > List View to change the folder view from tile to list format.• Touch > Change Size to change the size of the icons: Large, Normal or Small.

Using the MC40 | 47



• Touch > About File Browser to view the application version information.

PTT Express Voice Client

Note:

PTT Express Voice Client creates Push-To-Talk (PTT) communication capability between disparateenterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Expressdelivers simple PTT communication without the need of a voice communication server.

• Group Call: Press and hold the PTT (Talk) button to start communicating with other voice client users.• Private Response: Press and hold the Left Scan/Action (Private) button to respond to the originator of the last

broadcast or to make a Private Response.

PTT Audible IndicatorsThe following tones provide helpful cues when using the voice client.

• Talk Tone: Double chirp. Plays when the Talk (or Private) button is depressed. This is a prompt for the user tostart talking.

• Access Tone: Single beep. Plays when another user just finished a broadcast or response. The user is now able toinitiate a Group Broadcast or Private Response.

• Busy Tone: Continuous tone. Plays when the Talk (or Private) button is depressed and another user is alreadycommunicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).

• Network Tone:

- Three increasing pitch beeps. Plays when PTT Express has acquired the WLAN connection and the service isenabled.

- Three decreasing pitch beeps. Plays when PTT Express has lost the WLAN connection or the service isdisabled.

Figure 28: PTT Express Default User Interface

48 | Using the MC40



Table 8: PTT Express Default user Interface Descriptions

Item Description

Notification Icon Indicates the current state of the PTT Express client.

Service Indication Indicates the status of the PTT Express client. Options: Service Enabled, Service Disabledor Service Unavailable.

Talk Groups Lists all 32 Talk Groups available for PTT communication.

Settings Opens the PTT Express Settings screen.

Enable/DisableSwitch

Turns the PTT service on and off.

Enabling PTT CommunicationProcedure:

1 Touch .2

Touch .3 Slide the Enable/Disable Switch to the ON position. The button changes to a blue ON button.

Figure 29: PTT Express Window

Selecting a Talk GroupOne of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a timeon the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.

PTT CommunicationNote: This section describes the default PTT Express client configuration. See the PTT Express V1.2 UserGuide for detailed information on using the client.

PTT communication may be established as a Group Call or Private Response. When PTT Express is enabled, thebuttons on the left side of the device are assigned for PTT communication. When the Wired Headset is used, GroupCalls and Private Responses can also be initiated using the headset Talk button.

Using the MC40 | 49



Figure 30: MC40 PTT Buttons

1

2

1 Group Call Hard Button

2 Private Call Hard Button

Figure 31: Wired Headset

1

1 Talk Button

Creating a Group CallProcedure:

1 Press and hold the Group Call button (or the Talk button on the headset) and listen for the talk tone to play.If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTTExpress and the WLAN are enabled.

2 Start talking after the talk tone is heard.

Note: If the user holds the button for more than 60 seconds (default), the call is dropped allowing othersto make Group calls. The user should release the button when finished talking to allow others to makecalls.

50 | Using the MC40



3 Release the button when finished talking.

Responding to a Group BroadcastProcedure:

1 Wait until an access tone is heard.2 Press and hold the Talk button, and listen for the talk tone to play.

If a busy tone is heard, release the Talk button and wait a moment before making another attempt. Ensure thatPTT Express and the WLAN are enabled.

3 Start talking after the talk tone plays.4 Release the Talk button when finished talking.

Responding with a Private ResponseThe Private Response can only be initiated once a Group Call has been established. The initial Private Response ismade to the originator of the Group Call.

Procedure:

1 Wait until an access tone is heard.2 Within 10 seconds, press and hold the Private Response Hard Button, and listen for the talk tone to play.

If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTTExpress and the WLAN are enabled.

3 Start talking after the talk tone plays.4 Release the button when finished talking.

Responding with a Private Response with the Wired HeadsetThe Private Call can only be initiated once a Group Call has been established. The initial Private Response is made tothe originator of the Group Call.

Procedure:

1 Wait until an access tone is heard.2 Within 10 seconds, press and release and then press and hold the Talk button, and listen for the talk tone to play.

If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTTExpress and the WLAN are enabled.

3 Start talking after the talk tone plays.4 Release the button when finished talking.

Disabling PTT Express Voice Client CommunicationProcedure:

1 Touch .2

Touch .3 Slide the Enable/Diable Switch to the OFF position. The button changes to OFF.4 Touch .

VoIP Telephony Ready

The MC40 VoIP telephony-ready models are optimized to support telephony VoIP functionality.

Using the MC40 | 51



Use the Motorola Solutions Mobile Extensions Client or other 3rd party clients are required. Refer to thedocumentation provided with the client software for installation and usage information.

52 | Using the MC40



Chapter

3Data Capture

The MC40 offers the following data capture options:

• integrated imager• integrated digital camera• Magnetic stripe reader (MSR)• RS507 Hands-free imager.

Note:

By default, the good decode beep is set to system volume (Music and Media). The good decode beep canbe set to another sound (Notifications or Alarms) and the volume can be independently controlled. See theDataWedge section in the MC40 Integrator Guide for more information.

DataWedge is installed and enabled on the MC40 by default.

Imager

The device with an integrated imager has the following features:

• Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417,and 2D matrix code types.

• Advanced intuitive laser aiming cross-hair for easy point-and-shoot operation.

The modules uses digital camera technology to take a digital picture of a bar code, stores the resulting image in itsmemory, and executes state-of-the-art software decoding algorithms to extract the data from the image.

Operational ModesThe device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressinga scan button.

• Decode Mode: In this mode, the device attempts to locate and decode enabled bar codes within its field of view.The imager remains in this mode as long as the user holds the scan button, or until it decodes a bar code.

Note: To enable Pick List Mode, configure in DataWedge.

• Pick List Mode: This mode allows the user to selectively decode a bar code when more than one bar code is inthe device’s field of view. To accomplish this, move the aiming crosshair over the required bar code to decodeonly this bar code. This feature is ideal for pick lists containing multiple bar codes and manufacturing or transportlabels containing more than one bar code type (either 1D or 2D).

Digital Camera

The device with an integrated camera based bar code scanning solution has the following features:

53 | Data Capture



• Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, QR,PDF417, and 2D matrix code types.

• Cross-hair reticle for easy point-and-shoot operation.• Picklist mode to decode a particular bar code from many in the field of view.

The solution uses the advanced camera technology to take a digital picture of a bar code, and executes state-of-the-artsoftware decoding algorithms to extract the data from the image.

RS507 Hands-Free Imager

The RS507 Hands-free Imager is a wearable bar code scan solution for both 1D and 2D bar code symbologies. Thescanner supports Simple Serial Interface (SSI) and Bluetooth Human Interface Device (HID) connection to thedevice.

Figure 32: RS507 Hands-Free Imager

See to the RS507 Hands-free Imager Product Reference Guide for more information.

Scanning Considerations

Typically, scanning is a simple matter of aim, scan, and decode where a few quick trial efforts master it. However,consider the following to optimize scanning performance:

• Range

- Any scanning device decodes well over a particular working range — minimum and maximum distances fromthe bar code. This range varies according to bar code density and scanning device optics.

- Scanning within range brings quick and constant decodes; scanning too close or too far away preventsdecodes. Move the scanner closer and farther away to find the right working range for the bar codes beingscanned.

• Angle

- Scan angle is important for promoting quick decodes. When laser beams reflect directly back into the scannerfrom the bar code, this specular reflection can “blind” the scanner.

- To avoid this, scan the bar code so that the beam does not bounce directly back. But do not scan at too sharp anangle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practicequickly shows what tolerances to work within.

• Hold the device farther away for larger symbols.• Move the device closer for symbols with bars that are close together.

Note: Scanning procedures depend on the application and device configuration. An application may usedifferent scanning procedures from those described.

54 | Data Capture



Bar Code Capture with Imager

To capture bar code data:

Procedure:

1 Ensure that an application is open on the device and a text field is in focus (text cursor in text field).2 Point the top of the device at a bar code.

Figure 33: Bar Code Scanning

3 Press and hold the Scan button.

The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by thecross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.

The Left and Right LEDs light light green and a beep sounds to indicate the bar code was decoded successfully.Note that when the MC40 is in Pick List Mode, the MC40 does not decode the bar code until the center of thecrosshair touches the bar code.

Figure 34: Aiming Pattern

Figure 35: Pick List Mode with Multiple Bar Codes in Aiming Pattern

4 Release the scan button.5 The captured data appears in the text field.

Data Capture | 55



Bar Code Capture with Integrated Camera

To capture bar code data:

Procedure:

1 Ensure that an application is open on the device and a text field is in focus (text cursor in text field).2 Aim the camera at a bar code.3 Press and hold the Scan button. By default, a preview window appears on the screen. The Decode light emitting

diode (LED) lights red to indicate that data capture is in process.

Figure 36: Application with Preview Window

4 Move the device until the bar code is centered.5 The Decode LED lights green and a beep sounds to indicate the bar code was decoded successfully.6 The captured data appears in the text field.

Bar Code Capture with RS507 Hands-Free Imager

Prerequisites: Pair the RS507 with the MC40. See Pairing the RS507 Hands-Fee Imager Using SSI on page 58 or Pairing the RS507 Hands-Free Imager Bluetooth HID on page 58 for more information.

Procedure:

1 Ensure that an application is open on the device and a text field is in focus (text cursor in text field).2 Point the RS507 at a bar code.

56 | Data Capture



Figure 37: Bar Code Scanning with RS507

3 Press and hold the trigger.

The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by thecross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.

The RS507 LEDs light green, a beep sounds to indicate the bar code was decoded successfully. Note that whenthe RS507 is in Pick List Mode, the RS507 does not decode the bar code until the center of the crosshair touchesthe bar code.

Figure 38: Aiming Pattern

Figure 39: Pick List Mode with Multiple Bar Codes in Aiming Pattern

4 The captured data appears in the text field.

Data Capture | 57



Pairing the RS507 Hands-Fee Imager Using SSIAn RS507 Hands-free Imager can be used with the device to capture bar code data.

Procedure:

1 Ensure that the two devices are within 10 meters (32.8 feet) of one another.2 Install the battery into the RS507.3 On the MC40, touch .4 Touch .

Figure 40: Bluetooth Pairing Utility

5 Using the RS507, scan the bar code on the screen.The RS507 emits a high/low/high/low beeps. The Scan LED flashes green indicating that the RS507 is attemptingto establish connection with the MC40. When connection is established, the Scan LED turns off and the RS507emits one string of low/high beeps.

6 On the MC40, touch Exit.

Pairing the RS507 Hands-Free Imager Bluetooth HIDAn RS507 Hands-free Imager can be used with the device to capture bar code data.

Procedure:

1 Ensure that Bluetooth is enabled on both devices.2 Ensure that the Bluetooth device to discover is in discoverable mode.3 Ensure that the two devices are within 10 meters (32.8 feet) of one another.4 Place the RS507 in Human Interface Device (HID) mode. If the RS507 is already in HID mode, skip to step 5.

a Remove the battery from the RS507.b Press and hold the Restore key.c Install the battery onto the RS507.d Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.e Scan the bar code below to place the RS507 in HID mode.

58 | Data Capture



Figure 41: RS507 Bluetooth HID Bar Code

5 Remove the battery from the RS507.6 Re-install the battery into the RS507.7 On the MC40, touch .8 Touch .9 Touch Bluetooth.10 Touch SCAN FOR DEVICES. The device begins searching for discoverable Bluetooth devices in the area and

displays them under AVAILABLE DEVICES.11 Scroll through the list and select RS507.

The device connects to the RS507 and Connected appears below the device name. The Bluetooth device is addedto the Bluetooth devices list and a trusted (“paired”) connection is established.

Reading Magnetic Stripe Cards

Use the integrated MSR to read magnetic stripe card.

Note: Use the Card Swipe Tutorial application to practice swiping magnetic stripe cards through theMSR.

Procedure:

1 Ensure that MSR input is enabled in DataWedge and the cursor is in a text field.2 Grip MC40 firmly in one hand.3 Hold magnetic stripe card firmly in the other hand.4 Align the magnetic stripe on the card toward the display and swipe the card smoothly in either direction.

Data Capture | 59



Figure 42: Swiping a Magnetic Stripe Card

5 The captured data appears in the text field.

60 | Data Capture



Improper SwipingFigure 43: Do Not Start Swipe in Middle of Card

Data Capture | 61



Figure 44: Avoid Thumb Hitting Device

Figure 45: Do Not Hold End of Card While Swiping

62 | Data Capture



Figure 46: Do Not Swipe Card on Angle

DataWedge

DataWedge is a utility that adds advanced bar code scanning capability to any application without writing code. Itruns in the background and handles the interface to built-in bar code scanners. The captured bar code data isconverted to keystrokes and sent to the target application as if it was typed on the keypad.

To configure DataWedge refer to the MC40 Integrator Guide.

Enabling DataWedgeProcedure:

1 Touch .2

Touch .3 Touch .4 Touch Settings.5 Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that DataWedge

is enabled.6 Touch .

Data Capture | 63



Disabling DataWedgeProcedure:

1 Touch .2

Touch .3 Touch .4 Touch Settings.5 Touch the DataWedge enabled checkbox. The blue checkmark disappears from the checkbox indicating that

DataWedge is disabled.6 Touch .

64 | Data Capture



Chapter

4WLAN

Wireless local area networks (WLANs) allow the MC40 to communicate wirelessly inside a building. Before usingthe MC40 on a WLAN, the facility must be set up with the required hardware to run the WLAN (sometimes known asinfrastructure). The infrastructure and the MC40 must both be properly configured to enable this communication.

Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches, Radiusservers, etc.) for instructions on how to set up the infrastructure.

Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settingsto configure the MC40 to match the security scheme.

Note: Turn off Wi-Fi when not using it, to extend the life of the battery.

The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status. See Status Bar on page 32 formore information.

Scan and Connect to a Wi-Fi Network

To set up WLAN on the device:

Procedure:

1Touch .

2 Slide the Wi-Fi switch to the On position.3 Touch Wi-Fi. The MC40 searches for WLANs in the area and lists them.

65 | WLAN



Figure 47: Wi-Fi Screen

4 Scroll through the list and select the desired WLAN network.5 For open networks, touch Connect or for secure networks enter the required password or other credentials then

touch Connect. See the system administrator for more information.

The MC40 obtains a network address and other required information from the network using the dynamic hostconfiguration protocol (DHCP) protocol. To configure the MC40 with a fixed internet protocol (IP) address, Referto the MC40 Integrator Guide for more information.

6 In the Wi-Fi setting field, Connected appears indicating that the MC40 is connected to the WLAN.

66 | WLAN



Chapter

5Bluetooth

Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radiofrequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1).Bluetooth wireless technology is specifically designed for short-range (10 meters (32.8 feet) ) communication andlow power consumption.

Devices with Bluetooth capabilities can exchange information (e.g., files, appointments, and tasks) with otherBluetooth enabled devices such as printers, access points, and other mobile devices.

Adaptive Frequency Hopping

Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used withBluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work.There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveriesduring critical 802.11b communications. AFH for Bluetooth consists of four main sections:

• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-definedchannel mask.

• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.• Channel Maintenance - A method for periodically re-evaluating the channels.

When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFHcoexistence allows Motorola Enterprise Tablets to operate in any infrastructure.

The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mWand the expected range is 10 meters (32.8 ft.). A definition of ranges based on power class is difficult to obtain due topower and device differences, and whether one measures open space or closed office space.

Note: It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11boperation is required.

Security

The current Bluetooth specification defines security at the link level. Application-level security is not specified. Thisallows application developers to define security mechanisms tailored to their specific need. Link-level security occursbetween devices, not users, while application-level security can be implemented on a per-user basis. The Bluetoothspecification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt thedata flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while linkencryption is optional.

Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices andcreate a link key for them. Entering a common personal identification number (PIN) in the devices being pairedgenerates the initialization key. The PIN is never sent over the air. By default, the Bluetooth stack responds with no

67 | Bluetooth



key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devicesis based-upon a challenge-response transaction. Bluetooth allows for a PIN or passkey used to create other 128-bitkeys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairingdevices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.

Recommendations are:

• Perform pairing in a secure environment• Keep PIN codes private and do not store the PIN codes in the device• Implement application-level security.

Bluetooth Profiles

The MC40 supports the following Bluetooth services:

• Generic Access Profile (GAP) - Use for device discovery and authentication.• Service Discovery Protocol (SDP) - Handles the search for known and specific services as well as general

services.• Serial Port Profile (SPP) - Sets up a virtual serial port and connects two Bluetooth enabled devices. For example,

connecting the MC40 to a printer.• Human Interface Device Profile (HID) - Allows Bluetooth keyboards, pointing devices, gaming devices and

remote monitoring devices to connect to the MC40.• Object Push Profile (OPP) - Allows the MC40 to push and pull objects to and from a push server.• Dial-up Networking (DUN) - Allows the MC40 to access the Internet and other dial-up services using a Bluetooth

enabled mobile phone.• Headset Profile (HSP) - Allows a Bluetooth headset to communicate with the MC40.• Advanced Audio Distribution Profile (A2DP) - Allows the MC40 to stream stereo-quality audio to a wireless

headset or wireless stereo speakers.• Audio/Video Remote Control Profile (AVRCP) - Allows the MC40 to control televisions, hi-fi equipment, etc.

Bluetooth Power States

The Bluetooth radio is off by default.

• Suspend — When the MC40 goes into suspend mode, the Bluetooth radio state is retained upon resume.• Airplane Mode — When the MC40 is placed in Airplane Mode, the Bluetooth radio turns off. When in Airplane

Mode, the Bluetooth radio can be turned back on if desired.

Bluetooth Radio Power – Android

Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When theradio is off, other Bluetooth devices cannot see or connect to the device. Turn on the Bluetooth radio to exchangeinformation with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.

Note: To achieve the best battery life turn off radios when not in use.

68 | Bluetooth



Enabling BluetoothProcedure:

1 Touch .2 Slide the Bluetooth switch to the ON position. The Bluetooth icon also appears in the Status bar.3 Touch .

Disabling BluetoothProcedure:

1 Touch .2 Slide the Bluetooth switch to the OFF position.3 Touch .

Discovering Bluetooth Device(s)

The MC40 can receive information from discovered devices without pairing. However, once paired, the MC40 andthe paired device will exchange information automatically when the Bluetooth radio is on.

Procedure:

1 Ensure that Bluetooth is enabled on the device to discover.2 Ensure that the Bluetooth device to discover is in discoverable mode.3 Ensure that the two devices are within 10 meters (32.8 feet) of one another.4 Touch .5 If Bluetooth is off, slide the switch to the ON position.6 Touch Bluetooth.7 The MC40 begins searching for discoverable Bluetooth devices in the area and displays them under Available

Devices.8 Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.

Figure 48: Bluetooth Pairing - Enter PIN

Bluetooth | 69



Figure 49: Bluetooth Pairing — Simple Pairing

9 Enter a PIN in the text box and touch OK.10 Enter the same PIN on the other device. Touch Pair.11 The Bluetooth device is added to the Paired Devices list and a trusted (“paired”) connection is established.

Changing the Bluetooth Name

By default, the MC40 has a generic Bluetooth name that is visible to other devices when connected.

Procedure:

1 Touch .2 Touch Bluetooth.3 If Bluetooth is not on, slide the switch to the ON position.4 Touch .5 Touch Rename device.6 In the Rename device dialog box, enter a name and touch Rename.7 Touch .

Connecting to a Bluetooth Device

Once paired, connect to a Bluetooth device:

Procedure:

1 Touch .2 Touch Bluetooth.3 If Bluetooth is not on, slide the switch to the ON position.4 In the PAIRED DEVICES list, touch and hold on an unconnected Bluetooth device until a menu appears.5 Touch Connect. When connected, the device is displayed as connected in the list.

70 | Bluetooth



Selecting Profiles on the Bluetooth Device

Some Bluetooth devices have multiple profiles. To select a profile:

Procedure:

1 Touch .2 Touch Bluetooth.3 If Bluetooth is not turned on, slide the blue switch to the ON position.4

In the PAIRED DEVICES list, touch next to the device name.5 Under PROFILES, check or uncheck a profile to allow the device to use that profile.6 Touch .

Disconnecting from a Bluetooth Device

Procedure:

1 Touch .2 Touch Bluetooth.3 In the Bluetooth devices list, touch and hold on a device until a menu appears.4 Touch Disconnect.5 Touch .

Unpairing a Bluetooth Device

Procedure:

1Touch .

2 Touch Bluetooth.3

In the Paired Devices list, touch next to the device name.4 Touch Unpair.5 Touch .

Bluetooth | 71



Chapter

6Photos and Videos

This chapter provides information for taking photos and recording videos using the integrated digital cameras.

Note: Photos and videos are stored in Internal Storage.

Taking Photos

Note:

Camera settings are described in Camera Settings on page 76.

To take a photo:

Procedure:

1 Touch .2

Touch .

Figure 50: Camera Mode

3 If necessary, touch the options bar and touch .4

Touch to adjust exposure, flash, and other settings using the camera settings. See Camera Settings on page76 for more information.

73 | Photos and Videos



5Touch and to adjust the zoom level.

6 Frame the subject on screen.7

Touch .

The camera brings the image into focus. When the image is in focus, the focus indicators in each corner turngreen, the camera takes a photo and a shutter sound plays.

Note: To disable the shutter sound, turn notification sounds off. Touch > Sounds > Volumesand slide the Notifications slider all the way to the left.

Alternately, touch and hold to focus first, before taking a photo; then release to take a focused photo.

The photo appears momentarily then displays as a thumbnail in the upper right corner.8 Touch the thumbnail to view the photo in Gallery. See Viewing Photos and Videos on page 77 for more

information.

Taking a Panoramic Photo

Panorama mode lets the user create a single wide image by panning slowly across a scene. To take a panoramicphoto:

Procedure:

1 Touch .2

Touch .3

Touch the options bar and touch .

Figure 51: Panoramic Mode

4 Frame one side of the scene to capture.




5Touch and slowly start panning across the area to capture. A small white square appears inside the buttonindicating that the shot is in progress.

If panning too quickly, the message Too fast appears.6

Touch to end the shot. The panorama appears immediately and a progress indicator displays while it savesthe image.

7 Touch the thumbnail to view the photo in Gallery. See Viewing Photos and Videos on page 77.

Recording Videos

To record a video:

Procedure:

1Touch > .

2 Touch the options bar and touch .

Figure 52: Video Mode

3Touch to adjust exposure, flash, and other settings using the video settings. See Video Settings on page 76for more information.

4Touch and to adjust the zoom level.

5 Point the camera and frame the scene.6

Touch to start recording.

The device starts recording the video. The video time remaining appears in the top left of the screen.7

Touch to end recording.

Note: Previously recorded video displays in the thumbnail at the top right.

Photos and Videos | 75



8 Touch the thumbnail to access the Gallery application. See Viewing Photos and Videos on page 77.

Camera Settings

When in Camera mode, Camera settings are displayed on screen.

Touch to display the camera setting options.

• Settings - Touch to open a scrolling list of settings:

- Focus Mode - Touch to select the camera focus setting. Options: Macro, Infinity, Continuous or Auto(default).

- Capture Mode - Touch to select the capture mode. Options: High Quality (default) or Zero Shutter Lag.- Picture size - Touch to set the size (in pixels) of the photo. Options: 8M pixels (default), 5M pixels, 3M

pixels, 2M pixels, 1M pixels, VGA or QVGA.- ISO - Options: Auto (default), 100, 200, 400 or 800.- Picture quality - Touch to select picture quality setting. Options: Super fine (default), Fine or Normal.- Restore defaults - Touch Restore defaults to restore all camera settings to the default values.

• Scene mode - Touch to select a preset combination of camera settings designed for specific scenes.Options: Auto (default), Portrait, Landscape, Night, Steady Photo or Sports.

• Exposure - Touch to adjust the exposure settings. Options: +3, +2, +1, 0 (default), -1, -2, or -3.

• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the mostnatural-looking colors.

- Auto - Adjust the white balance automatically (default).- Incandescent - Adjust the white balance for incandescent lighting.- Daylight - Adjust the white balance for daylight.- Fluorescent - Adjust the white balance for florescent lighting.- Cloudy - Adjust the white balance for a cloudy environment.

Video Settings

When in Video mode, Video settings are displayed on screen.

Touch to display the video setting options.

• Settings - Touch to open a scrolling list of settings:

- Restore defaults - Touch Restore defaults to restore all video settings to the default values.• Video quality - Touch to select video quality:

- HD 1080p - High definition 1080p.- HD 720p - High definition 720p.- SD 480p - Standard definition 480p.

• Time lapse interval - Touch to select a time interval to set the frame rate for time lapse photography. Options:Off (default), 1s, 1.5s, 2s, 2.5s, 3s, 5s or 10s.




• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the mostnatural-looking colors.

- Auto - Adjust the white balance automatically (default).- Incandescent - Adjust the white balance for incandescent lighting.- Daylight - Adjust the white balance for daylight.- Fluorescent - Adjust the white balance for florescent lighting.- Cloudy - Adjust the white balance for a cloudy environment.

Viewing Photos and Videos

Note:

The device supports the following image formats: jpeg, gif, png and bmp.

The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.

Use Gallery to:

• view photos• play videos• perform basic editing of photos• set photos as wallpaper• set photos as a contact photo• share photos and videos.

To open the Gallery application, touch > or in the camera application touch the thumbnail image at the topright.

Gallery presents all photos and videos stored in the Internal Storage.

Figure 53: Gallery — Albums




• Touch an album to open it and view its contents. The photos and videos in the album are displayed inchronological order.

• Touch a photo or video in an album to view it.•

Touch icon (top left corner) to return to the main Gallery screen.

Working with AlbumsAlbums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in achronologically ordered grid. The name of the album displays at the top of the screen.

Figure 54: Photos Inside an Album

Swipe left or right to scroll images across the screen.

Share an AlbumProcedure:

1 Touch .

2Touch .

3 Touch and hold an album until it highlights.4 Touch other albums as required.5

Touch . The Share menu opens. Touch the application to use to share the selected albums.6 Follow the instructions within the selected application.

Get Album InformationProcedure:

1 Touch .

2Touch .




3 Touch and hold an album until it highlights.4

Touch .5 Touch Details.

Deleting an AlbumTo delete an album and its contents from the microSD card:

Procedure:

1 Touch .

2Touch .

3 Touch and hold an album until it highlights.4 Check other albums to delete. Ensure that other albums are selected.5

Touch .6 In the Delete selected item? menu, touch OK to delete the album.

Working with PhotosUse Gallery to view photos on the microSD card and edit and share photos.

Viewing and Browsing PhotosTo view a photo:

Procedure:

1 Touch .2

Touch .3 Touch an album to open it.4 Touch a photo.

Figure 55: Photo Example




5 Swipe left or right to view the next or previous photo in the album.6 Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is displayed

(but not saved) in the new orientation.7 Touch the photo to view the controls.8 Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.9 Drag the photo to view parts that are not in view.

Rotating a PhotoProcedure:

1 Touch a photo to view the controls.2 Touch .3 Touch Rotate Left or Rotate Right.

The photo is automatically saved with the new orientation.

Cropping a PhotoProcedure:

1 In Gallery, touch a photo to view the controls.2 Touch .3 Touch Crop. The blue cropping tool appears.4 Use the cropping tool to select the portion of the photo to crop.

• Drag from the inside of the cropping tool to move it.• Drag an edge of the cropping tool to resize it to any proportion.• Drag a corner of the cropping tool to resize it with fixed proportions.

Figure 56: Cropping Tool

5 Touch OK to save a copy of the cropped photo. The original version is retained.




Get Photo InformationProcedure:

1 Touch .2

Touch .3 Touch an album to open it.4 Touch the photo to open it.5 Touch .6 Touch Details.7 Touch Close.

Share a PhotoProcedure:

1 Touch .2

Touch .3 Touch an album to open it.4 Touch a photo to open it.5

Touch .6 Touch the application to use to share the selected photo. The application selected opens with the photo attached to

a new message.

Deleting a PhotoProcedure:

1 Touch .2

Touch .3 Touch an album to open it.4 Touch a photo to open it.5

Touch .6 Touch OK to delete the photo.

Working with VideosUse Gallery to view videos on the microSD card and share videos.

Watching VideosProcedure:

1 Touch .

2Touch .

3 Touch an album to open it.




4 Touch a video.

Figure 57: Video Example

5Touch . The video begins to play.

6 Touch the screen to view the playback controls.

Sharing a VideoProcedure:

1 Touch .

2Touch .

3 Touch an album to open it.4 Touch a video to open it.5

Touch . The Share menu appears.6 Touch the application to use to share the selected video. The application selected opens with the video attached to

a new message.

Deleting a VideoProcedure:

1 Touch .

2Touch .

3 Touch an album to open it.4 Touch a video to open it.5

Touch .6 Touch OK.




Chapter

7Accessories

This chapter provides information for using the accessories for the device.

MC40 Accessories

Table 9: MC40 Accessories on page 83 lists the accessories available for the MC40.

Table 9: MC40 Accessories

Accessory Part Number Description

Cradles

Single SlotCharge Only Cra-dle

CRDMC40XX-1000R Charges the MC40.

Five Slot ChargeOnly Cradle Base

CRDUNIV-XX-5000R Provides charging for up to five MC40 devices or four MC40 de-vices and one Four Slot Battery Charger using optional ChargingCups. Requires additional power supplies.

Five Slot ChargeOnly Cradle

CRDUNIV-40-5000R Provides charging for up to five MC40 devices.

Chargers

Four Slot BatteryCharger

SACMC40XX-4000R Charges up to four MC40 batteries.

Power Supply PWRS-124306-01R Provides power to the MC40 and Single Slot Charge Cradle.

Power Supply(12 VDC, 4.16A)

PWRS-14000-148C Provides power to the Five Slot Charge Only Cradle and theFour Slot Battery Charger.

Cables

Micro USB Ca-ble

25-MCXUSB-01R Provides power to the MC40 and USB communication with ahost computer.

US AC LineCord (3-wire)

23844-00-00R Provides power to the power supplies.

2-way DC Cable 25-122026-02R Connects one power supply (PWRS-14000-148C) to two FourSlot Battery Chargers.

4-way DC Cable 25-85992-01R Connects one power supply (PWRS-14000-241R) to four FourSlot Battery Chargers.

Table continued…

83 | Accessories



Accessory Part Number Description

Miscellaneous

Spare 2680 mAhlithium-ion bat-tery

BTRY-MC40EAB0E

BTRY-MC40EAB0E-10R

Replacement 2680 mAh battery.

Replacement 2680 mAh battery (10-pack)

Charging Cup CUPMC40XX-1000R Mounts onto the Five Slot Charge Only Cradle Base and pro-vides MC40 charging slot (Single pack).

Battery ChargerCup

CUPUNIBTRY-1000R Mounts on the Five Slot Charge Only Cradle Base and providesmounting for the Four Slot Battery Charger.

Universal BlankSlot Cover

CUPUNICVR-5000R Mounts on the Five Slot Charge Only Cradle and covers a slotwhen a cup is not required (5-pack).

Protective Rub-ber Boot

SG-MC40-RBOOT-01R

SG-MC40-RBOOT-10R

Provides additional protection for the MC40.

Provides additional protection for the MC40 (10–pack).

Soft Hip Holster SG-MC40HLSTR-02R Mounts on belt and provides storage for the MC40.

Finger Strap SG-MC40STRAP-01R

SG-MC40STRAP-10R

Mounts on the back of the MC40 and provides secure option forholding the device (Single pack or 10-pack).

Rack/WallMount Bracket

KT-UNIVLBRKT-01R Provides for mounting the Five Slot Charge Only Cradle onto astandard rack or wall.

Wired Headset HDST-25MM-PTVP-01 2.5 mm wired headset for PTT and VoIP telephony communica-tions.

Micro USB Cable

Use the Micro USB cable to connect the MC40 to the power supply for charging or to a host computer forcommunication.

84 | Accessories



Figure 58: Charging Using the Micro USB Cable

CommunicationWhen the MC40 is connected to a host computer using the Micro USB cable, the MC40 appears as a Removable Diskon the host computer. Refer to the MC40 Integrator Guide for more information.

Figure 59: Communication Using the Micro USB Cable

Single Slot Charge Cradle

The Single Slot Charge Cradle provides 5 VDC power for operating the MC40 and charging the battery.

Accessories | 85



Charging the MC40 BatteryConnect the cradle to power. Insert the MC40 into the slot to begin charging.

Figure 60: MC40 Battery Charging

The MC40’s Right light emitting diode (LED) indicates the status of the battery charging in the MC40. See Table 3:Battery Charge LED Status on page 23 for charging status indications. The 2680 mAh battery charges inapproximately four hours.

Charge batteries in ambient temperatures from 0 °C to 40 °C (32 °F to 104 °F) or up to 45 °C (113 °F) as reported by


Note that charging is intelligently controlled by the MC40. To accomplish this, for small periods of time, the MC40or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. TheMC40 or accessory indicates when charging is disabled due to abnormal temperatures via its Right LED. See Table 3:Battery Charge LED Status on page 23.

Five Slot Charge Only Cradle

The Five Slot Charge Only Cradle:

• Provides 5 VDC power for operating the MC40.• Simultaneously charges up to five MC40s.

86 | Accessories



• Consists of a cradle base and optional cups that can be configured for various charging requirements.• Provides mounting for a Four Slot Battery Charger (requires separate power supply).

See the MC40 Integrator Guide for setup and configuration instructions. To charge the MC40, insert the MC40 intoan open slot.

Figure 61: Charging MC40s and Spare Batteries

The MC40’s Right LED shows the status of the battery charging. See Table 3: Battery Charge LED Status on page 23for charging status indications. The 2680 mAh battery charges in approximately four hours.



Accessories | 87



Note that charging is intelligently controlled by the MC40. To accomplish this, for small periods of time, the MC40or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. TheMC40 or accessory indicates when charging is disabled due to abnormal temperatures via its Right LED. See Table 3:Battery Charge LED Status on page 23.

Four Slot Battery Charger

The Four Slot Battery Charger:

• Provides 12 VDC power for charging the batteries.• Simultaneously charges up to four MC40 batteries.

To charge a spare battery:

Figure 62: Four Slot Battery Charger

The Four Slot Battery Charger has four amber Battery Charging LEDs, one for each battery charging well. The 2680mAh battery charges in approximately four hours.


the battery. To view the battery temperature, touch > About device > Battery Information. Charging isintelligently controlled by the MC40. To accomplish this, for small periods of time, the charger alternately enablesand disables battery charging to keep the battery at acceptable temperatures. The charger indicates when charging isdisabled due to abnormal temperatures via its LED.

88 | Accessories



Table 10: Spare Battery Charge LED Status

Status Indications

Off No battery in a slot.

Battery is not charging.

Battery is not inserted correctly in the charger.

Charger is not powered.

Slow Blinking Amber Battery is charging.

Solid Green Charging complete.

Fast Blinking Amber Charging error, e.g.:

• Temperature is too low or too high.• Charging has gone on too long without completion.

Accessories | 89



Chapter

8Maintenance and Troubleshooting

This chapter includes instructions on cleaning and storing the device, and provides troubleshooting solutions forpotential problems during operation.

Maintaining the MC40

For trouble-free service, observe the following tips when using the MC40:

• Do not scratch the screen of the MC40. When working with the MC40, use only a finger. Never use an actual penor pencil or other sharp object on the surface of the MC40 screen.

• The touch-sensitive screen of the MC40 is glass. Do not to drop the MC40 or subject it to strong impact.• Protect the MC40 from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it

away from heat sources.• Do not store or use the MC40 in any location that is dusty, damp, or wet.• Use a soft lens cloth to clean the MC40. If the surface of the MC40 screen becomes soiled, clean it with a soft

cloth moistened with a diluted window-cleaning solution.• Periodically replace the rechargeable battery to ensure maximum battery life and product performance. Battery

life depends on individual usage patterns.

Battery Safety Guidelines

• The area in which the units are charged should be clear of debris and combustible materials or chemicals.Particular care should be taken where the device is charged in a non commercial environment.

• Follow battery usage, storage, and charging guidelines found in this guide.• Improper battery use may result in a fire, explosion, or other hazard.• To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF (0

ºC and +40 ºC)• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of

fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or acharger, contact Motorola Solutions Global Customer Support Center.

• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bearthe USB-IF logo or have completed the USB-IF compliance program.

• Do not disassemble or open, crush, bend or deform, puncture, or shred.• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or

other liquids, or expose to fire, explosion, or other hazard.• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a

radiator or other heat source. Do not place battery into a microwave oven or dryer.• Battery usage by children should be supervised.• Please follow local regulations to properly dispose of used re-chargeable batteries.

91 | Maintenance and Troubleshooting



• Do not dispose of batteries in fire.• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been

made, wash the affected area with large amounts of water and seek medical advice.• If you suspect damage to your equipment or battery, contact Motorola Solutions Global Customer Support Center

to arrange for inspection.

Cleaning Instructions

Caution:

Always wear eye protection.

Read warning label on compressed air and alcohol product before using.

If you have to use any other solution for medical reasons please contact Motorola for more information.

Warning: Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposureoccurs, unplug the device and clean the product immediately in accordance with these guidelines.

Approved Cleanser Active Ingredients100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropylalcohol, bleach/sodium hypochlorite, hydrogen peroxide or mild dish soap.

Harmful IngredientsThe following chemicals are known to damage the plastics on the device and should not come in contact with thedevice: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinatedhydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolicacid and TB-lysoform.

Cleaning InstructionsDo not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device inthe cloth or wipe, but gently wipe the unit. Be careful not to let liquid pool around the display window or other places.Allow the unit to air dry before use.

Special Cleaning NotesMany vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known tobe harmful to the housing of the device. The device should not be handled while wearing vinyl gloves containingphthalates, or before hands are washed to remove contaminant residue after gloves are removed. If productscontaining any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizerthat contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the plastics.

Cleaning Materials Required• Alcohol wipes• Lens tissue• Cotton-tipped applicators• Isopropyl alcohol• Can of compressed air with a tube.




Cleaning FrequencyThe cleaning frequency is up to the customer’s discretion due to the varied environments in which the mobile devicesare used. They may be cleaned as frequently as required, but it is advisable to clean the camera window periodicallywhen used in dirty environments to ensure optimum performance.

Cleaning the MC40

HousingUsing the alcohol wipes, wipe the housing including keys and in-between keys.

DisplayThe display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquidaround the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.

Exit and Camera WindowWipe the camera window periodically with a lens tissue or other material suitable for cleaning optical material suchas eyeglasses.

Connector CleaningTo clean the connectors:

Procedure:

1 Remove the main battery from mobile computer.2 Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.3 Rub the cotton portion of the cotton-tipped applicator back-and-forth across the connector. Do not leave any

cotton residue on the connector.4 Repeat at least three times.5 Use the cotton-tipped applicator dipped in alcohol to remove any grease and dirt near the connector area.6 Use a dry cotton-tipped applicator and repeat steps 4 through 6.

Caution: Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.

7 Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface.8 Inspect the area for any grease or dirt, repeat if required.

Cleaning Cradle Connectors

To clean the connectors on a cradle:

Procedure:

1 Remove the DC power cable from the cradle.2 Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.3 Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator

back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.4 All sides of the connector should also be rubbed with the cotton-tipped applicator.

Maintenance and Troubleshooting | 93



Caution: Do not point nozzle at yourself and others, ensure the nozzle or tube is pointed away fromyour face.

5 Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away from the surface.6 Remove any lint left by the cotton-tipped applicator.7 If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.8 Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before

applying power to cradle.If the temperature is low and humidity is high, longer drying time is required. Warm temperature and dry humidityrequires less drying time.

Troubleshooting the MC40

Table 11: Troubleshooting the MC40

Problem Cause Solution

When the user pressesthe Power button, theMC40 does not turn on.

Battery is com-pletely dis-charged.

Re-charge or replace the battery.

Battery not in-stalled properly.

Install the battery properly. See Installing the Battery on page 22.

Power button notheld down longenough.

Press the Power button until the Right LED flashes once.

MC40 not re-sponding.

Perform a hard reset. See Resetting the Device on page 45.

When the user pressesthe Power button theMC40 does not turn onbut the Decode LEDblinks amber.

Battery chargelevel is very low.

Re-charge or replace the battery.

Battery did not charge. Battery failed. Replace battery. If the MC40 still does not operate, perform a hard-ware reset. See Resetting the Device on page 45.

MC40 was re-moved frompower while bat-tery was charg-ing.

Insert MC40 in cradle. The 2680 mAh battery fully charges in lessthan four hours.

Extreme batterytemperature.

Battery does not charge if ambient temperature is below 0 °C (32 °F)or above 40 °C (104 °F).

During data communica-tion, no data transmitted,or transmitted data wasincomplete.

MC40 discon-nected from hostcomputer duringcommunication.

Reattach the communication cable and re-transmit.

Incorrect cableconfiguration.

See the system administrator.

Table continued…





No sound. Volume setting islow or turned off.

Adjust the volume.

MC40 turns off. MC40 is inac-tive.

The display turns off after a period of inactivity. Set this period to 15seconds, 30 seconds, 1, 2, 10, or 30 minutes.

Battery is deplet-ed.

Recharge or replace the battery.

A message appears stat-ing not enough storagememory.

Too many appli-cations installedon the MC40.

Remove user-installed applications on the MC40 to recover memory.

Select > Apps > Downloaded. Select the unused programsand touch Uninstall.

The MC40 does not de-code when reading barcode.

DataWedge isnot enabled.

Ensure that DataWedge is enabled and configured properly. Refer tothe MC40 Integrator Guide for more information.

Unreadable barcode.

Ensure the symbol is not defaced.

Distance betweenthe MC40 andbar code is incor-rect.

Place the MC40 within proper scanning range.

MC40 is not pro-grammed for thebar code type.

Program the MC40 to accept the type of bar code being scanned. Re-fer to the MC40 Integrator Guide for DataWedge configuration.

MC40 is not pro-grammed to gen-erate a beep.

If the MC40 does not beep on a good decode, set the application togenerate a beep on good decode.

MC40 cannot find anyBluetooth devices near-by.

Too far from oth-er Bluetooth de-vices.

Move closer to the other Bluetooth device(s), within a range of 10 me-ters (30 feet).

The Bluetoothdevice(s) nearbyare not turned on.

Turn on the Bluetooth device(s) to find.

The Bluetoothdevice(s) are notin discoverablemode.

Set the Bluetooth device(s) to discoverable mode. If needed, refer tothe device’s user documentation for help.

MC40 does not readmagnetic stripe card.

Magnetic stripeon the card isfacing the wrongway.

Ensure that magnetic stripe card is oriented correctly. Magnetic stripeon the card should be facing the display.

Cannot connect toWLAN.

Access Point(AP) does notbroadcast coun-try code.

Disable 802.11d feature. Touch > Wi-Fi > > Advanced.Deselect the Enable 802.11d checkbox.

Wired headset is notworking as headset hookor not able to initiate aPTT call even throughwired headset.

Wired headsetnot connectedproperly.

Ensure that the wired headset is connected properly.




Single-Slot Charge Cradle Troubleshooting

Table 12: Troubleshooting the Single-slot Charge Cradle


MC40 battery is notcharging.

MC40 was re-moved from cra-dle or cradle wasunplugged fromAC power toosoon.

Ensure cradle is receiving power. Ensure MC40 is seated correctly.Confirm the battery is charging. The 2680 mAh battery charges in ap-proximately four hours.

Battery is faulty. Verify that other batteries charge properly. If so, replace the faultybattery.

The MC40 is notfully seated in thecradle.

Remove and re-insert the MC40 into the cradle, ensuring it is firmlyseated.

Extreme batterytemperature.

Battery does not charge if ambient temperature is below 0 °C (32 °F)or above 40 °C (104 °F).

Five-Slot Charge Only Cradle CRDUNIV-40–5000RTroubleshooting

Table 13: Troubleshooting the Five-Slot Charge Only Cradle


Battery is not charging. MC40 removedfrom the cradletoo soon.

Replace the MC40 in the cradle. The 2680 mAh battery charges in ap-

proximately four hours. Touch > About device > Status toview battery status.


MC40 is not in-serted correctly inthe cradle.

Remove the MC40 and reinsert it correctly. Verify charging is active.

Touch > About device > Status to view battery status.

Ambient temper-ature of the cradleis too warm.

Move the cradle to an area where the ambient temperature is between0 °C (32 °F) and 35 °C (95 °F).

Spare batteries are notcharging in Four SlotBattery Charger.

Missing Four SlotBattery Chargerpower supply.

The Four Slot Battery Charger requires a separate power supply. Ob-tain the correct power supply and connect to the charger.




Four-Slot Battery Charger SACMC40XX-4000R Troubleshooting

Table 14: Troubleshooting the Four-slot Battery Charger


Battery not charging. Battery was re-moved from thecharger or charg-er was unpluggedfrom AC powertoo soon.

Re-insert the battery in the charger or re-connect the charger’s powersupply. The 2680 mAh battery charges in approximately four hours.


Battery contactsnot connected tocharger.

Verify that the battery is seated in the battery well correctly with thecontacts facing down.




Chapter

9Technical Specifications

The following sections provide technical specification for the device.

MC40 Technical Specifications

The following table summarizes the MC40’s intended operating environment and technical hardware specifications.

Table 15: MC40 Technical Specifications

Item Description

Physical Characteristics

Dimensions Height: 143.9 mm (5.66 in.)

Width: 72.8 mm (2.87 in.)

Non-MSR: Depth: 20.1 mm (0.79 in.)

MSR: Depth: 31.8 mm (1.25 in.)

Weight Non-MSR: 257.7 g (9.09 oz.)

MSR: 266.1 g (9.38 oz.)

Display 4.3 in. capacitive; 480 x 800; 300 nit

Touch Panel Capacitive dual-touch

Backlight LED backlight

Battery Rechargeable Lithium Ion 3.7V, 2680 mAh Smart battery.

Backup Battery NiMH battery (rechargeable) 15 mAh 3.6 V (not user accessible).

Connectivity One USB 2.0 OTG connector.

Notification LED, audio and vibration.

Keypad Options On-screen keyboard.

Audio Speakers, microphone and headset connector (mono, 2.5 mm jack with micro-phone). Stereo audio through Bluetooth stereo headsets.

Disinfectant Ready Yes (Healthcare version)

Colors Silver, Healthcare Blue and White

Communications All models: Push-to-Talk. PTT Express Client pre-loaded. VoIP Telephony Readymodels: Optimized for VoIP telephony. VoIP client not included.

Table continued…

99 | Technical Specifications



Item Description

Performance Characteristics

CPU Texas Instruments OMAP 4430 @ 800 MHz, dual-core.

Operating System Android-based ASOP 4.1.1.

Memory 1 GB RAM, 8 GB Flash.

Output Power (USB) Docking Connector: 5 VDC @ 500 mA max.

User Environment

Operating Temperature 0°C to 50°C (32°F to 122°F)

Storage Temperature -40°C to 70°C (-40°F to 158°F)

Charging Temperature 0° C to 40° C (32°F to 104°F)

Humidity 5% to 95% RH non-condensing

Drop Specification Multiple 1.2 m (4 ft.) drops to plywood per MIL-STD 810G specifications. Multi-ple 0.9 m (3 ft.) drops to tile.

Electrostatic Discharge (ESD) +/-15kVdc air discharge, +/-8kVdc direct discharge, +/-2kVdc indirect discharge

Sealing IP54

Wireless LAN Data Communications

Wireless Local Area Network(WLAN) radio

IEEE® 802.11a/b/g/n/r with internal antenna

Data Rates Supported 802.11b: 1, 2, 5.5, 11 Mbps

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps

802.11n: 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps

802.11n with SGI: 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65, 72.2 Mbps

Fast Roam: Pre-Authentication, PMKID Caching, Opportunistic Key Cach-ing(OKC), Cisco CCKM, Motorola HFSR, 802.11r

Certifications: Wi-Fi, CCXv4

Operating Channels Chan 36 - 165 (5180 – 5825 MHz), Chan 1 - 13 (2412 - 2472 MHz); actual operat-ing channels/frequencies depend on regulatory rules and certification agency.

Security Security Modes: Legacy, WPA and WPA2

Encryption: WEP (40 and 128 bit), TKIP and AES

Authentication: TLS, TTLS (MSCHAP), TTLS (MSCHAPV2), TTLS (PAP),PEAP (MSCHAPV2), PEAP (GTC), FAST (MSCHAPV2), FAST (GTC), LEAP.

CCXv4 certified.

Spreading Technique Direct Sequence Spread Spectrum (DSSS) and Orthogonal Frequency DivisionMultiplexing (OFDM)

Wireless PAN Data and Voice Communications

Bluetooth Class II, v 2.1 with EDR; integrated antenna.

Data CaptureTable continued…




Item Description

Imager Captures 1D and 2D bar codes.

Rear-facing Camera For bar code scanning and image capture: 8 MP auto-focus camera with aiming;captures 1D and 2D bar codes, photographs, video, signatures and documents.

Magnetic Stripe Reader Reads data on magnetic stripe cards.

RS507 Hands-free Imager Captures 1D and 2D bar codes.

Sensors

Motion Sensor 3-axis accelerometer that enables motion sensing applications for dynamic screenorientation and power management.

Ambient Light/Proximity Sen-sor

Automatically adjusts display brightness and turns off the display during PTT calls.

Imager (SE4500-DL) Specifications

Field of View Horizontal - 39.2°

Vertical - 25.4°

Optical Resolution WVGA 752 H x 480 V pixels (gray scale)

Roll 360°

Pitch Angle +/- 60° from normal

Skew Tolerance +/- 60° from normal

Ambient Light Indoor: 450 ft. candles (4845 lux)

Outdoor: 9000 ft. candles (96,900 lux)

Sunlight: 8000 ft. candles

Fluorescent: 450 ft. candles

Focal Distance From center of exit window: 18.5 cm (7.3 in.)

Aiming Element (VLD) 655 nm +/- 10 nm

Illumination Element (LED) 625 nm +/- 5 nm

Supported Symbologies

1D Chinese 2 of 5, Codabar, Code 11, Code 128, Code 39, Code 93, Discrete 2 of 5,EAN-8, EAN-13, GS1 DataBar, GS1 DataBar Expanded, GS1 DataBar Limited,Interleaved 2 of 5, Korean 2 of 5, MSI, TLC 39, Matrix 2 of 5, Trioptic, UPCA,UPCE, UPCE1, Web Code.

2D Australian Postal, Aztec, Canadian Postal, Composite AB, Composite C, Data Ma-trix, Dutch Postal, Japan Postal, Maxicode, Micro PDF, Micro QR, PDF, QR Code,UK Postal, US Planet, US Postnet, US4State, US4State FICS.

Technical Specifications | 101



Single-Slot Charge Cradle CRDMC40XX-1000R TechnicalSpecifications

Table 16: Single-slot Charge Cradle Technical Specifications

Item Description

Dimensions Height: 69.4 mm (2.73 in.)

Width: 102.5 mm (4.04 in.)

Depth: 88.9 mm (3.50 in.)

Weight 274 g (9.67 oz)

Input Voltage 5 VDC

Power Consumption (withMC40)

6 watts

Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)

Storage Temperature -40 °C to 70 °C (-40 °F to 158 °F)

Charging Temperature 0 °C to 40 °C (32 °F to 104 °F)

Humidity 0% to 95% non-condensing

Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.

Electrostatic Discharge (ESD) +/- 15 kV air

+/- 8 kV contact

Five-Slot Charge Only Cradle CRDUNIV-40-5000R TechnicalSpecifications

Table 17: Five-Slot Charge Only Cradle Technical Specifications

Item Description

Dimensions (Base only) Height: 40.2 mm (1.6 in.)

Width: 449.6 mm (17.7 in.)

Depth: 120.3 mm (4.7 in.)

Dimensions (Base with fiveCharging Cups)

Height: 90.1 mm (3.5 in.)

Width: 449.6 mm (17.7 in.)

Depth: 120.3 mm (4.7 in.)

Dimensions (Base with fourCharging Cups and one BatteryCharger Cup

Height: 77.0 mm (3.0 in.)

Width: 449.6 mm (17.7 in.)

Table continued…




Item Description

Depth: 120.3 mm (4.7 in.)

Weight (Base only) 0.93 kg (20.5 lbs.)

Weight (Base with five Charg-ing Cups))

1.31 kg (2.89 lbs.)

Weight (Base with four Charg-ing Cups and one BatteryCharger Cup)

1.30 kg (2.86 lbs.)

Input Voltage 12 VDC


37.5 watts





Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.


+/- 8 kV contact

Four-Slot Battery Charger SACMC40XX-4000R TechnicalSpecifications

Table 18: Four-slot Battery Charger Technical Specifications

Item Description

Dimensions (with USB HostExpansion Module)

Height: 59.9 mm (2.36 in.)

Width: 84.0 mm (3.31 in.)

Depth: 116.3 mm (4.58 in.)

Weight 257 g (9.07 in.)

Input Voltage 12 VDC


25 watts





Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.Table continued…

Technical Specifications | 103



Item Description


+/- 8 kV contact




Index

Aadaptive frequency hopping 67albums 78android version 15application shortcuts 35approved cleanser 92

Bback button 20battery

charging 22management 25replacement 24

bluetoothconnecting to a device 70profiles 71

BluetoothPIN 67security 67

build number 15

Ccamera

rear-facing 21camera settings 76cleaning 92cleaning instructions 92configuration 15cradle

connector cleaning 93creating folders 36

Ddatawedge 63decode mode 53default notifications 29digital camera 53display

cleaning 93

Ffile browser 46five-slot charge only cradle base 83four slot battery charger 83

Hharmful ingredients 92home button 20

Kkeyboard 38

Llight sensor 19

Mmemory 15menu button 20micro USB cable 83microphone 19

Nnaming folders 36

Ooperating system 15

Ppanoramic 74photos 73picklist mode 53power button 20power on 23

Rradios 15recording videos 75replacing the battery 24resetting 45right LED 20rotate screen 27RS507 scanning 56

Sscan angle 54scanning range 54screen lock sounds 29screen rotation 27screen timeout 28serial number 15service information 17set date 26set time 26set time zone 26setting

camera 76video 76

Index | 105

single-slot charge only cradle 83soft reset 45spare battery 84status bar 32system sounds 29

Ttaking a panoramic photo 74taking photos 73touch screen 20

Vvibrate on touch 29video settings 76videos 73, 75volume 28

106 | Index