manual - himodel · suggest you read the manual carefully before using this item support and...

SUPER-LINK 2.4GHz RADIO ADAPTER MANUAL

I

SUPER-LINK 2.4 GHz Module CW-8

MANUAL

NoticeNoticeNoticeNotice：：：：Please read the manual carefully before using itPlease read the manual carefully before using itPlease read the manual carefully before using itPlease read the manual carefully before using it


www.super-link.cn - 1 -

CatalogueCatalogueCatalogueCatalogue

State ……………………………………………………………………..…………2

Support & service …………………………………………………………………2

Specific symbol ……………………………………………………………………2

Flight safety …………………………………………………………..……………2

SUPER-LINK CW-8 module and accessories………………………………… 3

SUPER-LINK CW-8 compatible……………………………………………….…4

Charging instruction…………………………………………………….…………5

About SUPER-LINK system………………………………………………………5

SUPER-LINK CW-8 parameter……………………………………………..……5

SLink series receiver parameter……………………………………...………… 5

SUPER-LINK CW-8 layout instruction………………………………………..…6

Operation ………………………………………………………………………..…6

SUPER-LINK CW-8 installation……………………………………………..……6

Bind ………………………………………………………………………..……..…6

SUPER-LINK CW-8voltage calibrate ……………………………...…..………7

SLink series receiver installation…………………………………………….……7

Failsafe………………………………………………………………………………8

ID setting………………………………………………………………….…………8

Attach：Module LED indicate …………………………………………….………8



State Thanks for choosing SUPER-LINK 2.4GHz module CW-8 and its series receivers. We suggest you read the manual carefully before using this item

Support and service If you have any question on using the unit, please read the manual carefully. You can also contact with our dealers or visit www.super-link.com to get the customer service.

Specific symbol

Please notice these symbols and read them carefully .

Dangerous ：：：：If you can’t operation as normal, it may be dangerous or bad to your life.

Warning ：：：：If you can’t operation as normal, it may be dangerous or bad to your life.

Notice ：：：：If you can’t operation as normal, it may be dangerous or bad to your life.

Symbol ：：：： Prohibit Force

Flight safety Any electronic may lose control, please set up failsafe correctly to avoid or reduce losses. If you find the unit with problem please don’t use it and contact us in time. Don’t use it in the rainy day or windy.

For the operator itself operation error caused by damage to the product, or are derived from the other problems, it shall not with SUPER - LINK. Range is affected by the environment .Please test range in the open away from any obstacles.Our range test is based on ground.

Due to some receivers with high sensitivity, some of RX and TX may has blocking(In general. The distance of RX wire and TX wire keeps within 30CM).This won’t influence the normal working

Please note the positive and negative charges on the voltage protector,don’t make mistake



SUPER-LINK CW-8 module and accessories for choose

CW-8 module



Accessories include：：：：CW8 module………………X1 CW8 antenna………………X1

S1…………………..…………X1

S2………………………..……X1

SUPER-LINK CW-8 compatible 4YF (72MHz), 4YBF, 6EX, 6J, 8J, 7C, 8FG, 9C, 10C & 12FG

S1(included)

4VF, 5U, 6A, 6DA, 6H, 6YF, 6YG, 7NFK, 8U & 9Z S3 Futaba

4YF (2.4GHz), 12Z, 14MZ & 18MZ S1(included) & S6

JR All aircraft transmitters with trainer/DSC jack S2(included)

WFT06II, WFT07II, WFT08, WFT08X, WFT08, WFT09, WFT09II

S4 & S6 WFLY

WFT06X-A, FT06-A, FT06-C S5 & S6

Neon, Flash 4sx, 5, 5sx, Focus 4, 6, Laser 4, 6, Optic 5 (72MHz), Optic 6 (72MHz, 2.4GHz), Eclipse 7 (72MHz), Prism 7 & Prism 7X

S3

Aurora 9 Hitec

Optic 5, Optic 6 Sport & Eclipse 7 (2.4GHz) S5 & S6

DX6, DX6i & DX7 S2(included) Spektrum

DX4e, DX5e, DX7s, DX8, DX10t & DX18 S5 & S6

4TH & 6XM S1(included) Tower Hobbies

4FM & 6FM S3

Graupner MX-16 S2 (included)

FS FS-CT6B, S4 & S6

Walkera All aircraft transmitters with trainer/DSC jack S5 & S6

Charging instruction If analog of radio with power, you can use S1or S3 to work with super-link CW8 If analog of radio with power, but the charge port with power, you can use S2 to work with SUPER-LINK CW8. If analog and charge port without power, you can use S4or S5 to work with SUPER-LINK CW8, and meantime use S6 to supply power for SUPER-LINK CW8 module.



About SUPER-LINK SYSTEM SUPER-LINK CW-8 module and receivers with the standard of Frequency-Hopping Spread Spectrum (FHSS), so in actual use, the surrounding environment of the interference signal is difficult to interference signals from the transmitter and receiver. This ensure safe, stable. The system has high reliability, good compatibility, the better control, more agile identification control and lower power consumption. It adopts DC power; the normal working current is less than 30 mA, which saves electricity. At the same time, the SUPER - LINK CW8 module will supply the firmware to users for updating.

SUPER-LINK CW8 module and Slink series receiver fea tures ●Long Range, light weight ●Easy to bind and operation ●Receiver is small and light ●Failsafe. You can set the receiver to default to a pre-set position on all channels in the

unlikely event of signal loss. ●Scan the clear frequency channel and then make signal transmission. ●Ultra-low power design.

SUPER-LINK CW-8 parameter

Dimension 52*33.5*12.5mm Operating current

30mA

Operating Voltage

3.7～4.2V(connect with 1S battery) 4～12.6V(power supplied by Transmitter)

Power <100mW

Resolution 1µs

Slink receivers specifications Item No. Slink4RC（4ch） SLink4R（4ch） SLink7R（7ch）

Dimension(mm) 17X15.1X5.6 24×15.1×5.6 34.2×18.4×8.7

Weight 1.1g 2.2g 9g

Control range 400m 800m 800m

Operating Voltage 3.7V～6.0V 3.7V～6.0V 4.8V～6.0V



SUPER-LINK CW-8 version instruction

SUPER-LINK CW-8 installation 1. Inserting the simulated line to the analog port of SUPER-LINK CW8; 2. Screw the 2.4G antenna and ensure antenna tightening; 3. Reference to “Slink receivers bind” to operate the bind of module and receiver; 4. Reference to "SUPER - LINK CW8 voltage calibration" to make the calibration voltage; 5. Reference to “Failsafe setting” to set the failsafe of receiver; 6. Reference to “ ID setting” to change the ID; 7. After finished above, please find the suit place for the module on the transmitter and

please avoid the antenna touched with metal; Kindly inform: SUPER-LINK CW8 had finished calibrat ion voltage, ID setting, if there is no special need, please don’t do the operate.

Slink receivers Bind 1. Press the button on the TX module and turn on the transmitter. The LED on the module

will light red and green for 1s, please remove your hand during the green light 1s .The buzzer will sound one , the LED on the module will flash between red and green ,gets into bind state.



2、SLink4RC reference to Slink 4rc(Bind way 1)；SLink4R、SLink7Rreference to bind way2.

Bind way1 （suit to SLink4RC）

Bind way 2（suit to SLink4R、SLink7R）

After SUPER-LINK gets into bind, connect the receiver to the battery; The LED on the receiver will light. The LED will flash quickly and go out. This shows that the receiver has bound to the module. Turn off the power to the receiver and turn off the transmitter.

After bind of SUPER-LINK CW8,press and hold the button on the receiver. Connect the receiver to the battery. The LED on the receiver will light (LED will light 1s, please make sure to released your hand within 1s), The LED will flash quickly several times and go out. Turn off the power to the receiver. If you do not want to bind more receivers at this time, turn off the transmitter.

Don’t press any button on the module. Turn the transmitter on. The module LED should be green. Connect the receiver to the battery. The red LED on the receiver will flash three times (now it is searching for the frequency) and light on for long, indicating the receiver is operating properly. If not bind successful, the red LED on the receiver will put off or flash. The receiver will not be initialized; it is also the most safe test model boundary.

SUPER-LINK CW8 voltage calibrate Press the button the module and turn on the transmitter (supply power to module), The LED on the module will light red and green for 1s, please remove your hand during the green light 1s.The buzzer will sound two, gets into voltage calibrate, In the battery outlet connect the correct 4.2 V standard voltage, press the button until the buzzer gave a short sound, voltage calibration finished.

SLink receivers installation



Failsafe setting: Any electronic may lose control, please set up failsafe correctly to avoid or reduce losses. 1. after initial binding, turn on the transmitter. 2. Press and hold the button on the receiver (under the symbol of “Thumb”). Connect the

receiver to the battery. The LED on the receiver will light（about 1s） and then go out (for about 1s）. At this time (when the LED off) remove your hand from the receiver button. The LED on the receiver will go on.

3. Move the joystick on your transmitter to where you want the surfaces / motor etc to be in the event of lost signal. Press the button on the receiver .The LED will flash several times; this shows the receiver has remembered the position which you have set. In the rare event that your system losses signal, all channels will return to the position which you have set.

4. Turn off the power to the receiver. Failsafe is now set. 5. Check that failsafe works, by turning on the transmitter then the receiver / model. Turn

off the transmitter. The controls should go to their preset position. They will return to those on the transmitter when power is restored.

ID Setting Press the button on the module and turn on the transmitter, the red and green LED will

light for 1s,then green and red light for 1s again, please released the button within1s, the buzzer will sounds three and gets into ID mode. During accounting ID, buzzer will sound a short, one ID one sound, now press the button and buzzer will sound a long, and it means ID was saved.

If you don’t released the button in time or the time press the button is long, the module will gets into normal working.

Attach: Instruction of LED on the TX module

Green LED light on Normal working

Yellow LED stay on range testing

LED flash between red and green Bind code

Flash red LED Change TX module ID condition

If you have any questions please do not hesitate to contact us or visit our website: www.super-link.cn Or contact with your local supplier.

manual - himodel · suggest you read the manual carefully before using this item support and...

Documents