manual for cycle 1

www.unistring.com

User Manual

For

UTS-MC-KIT-M7.1.1

by

G. Kumar

Sr Design Engineer

M.Siva Prasad

Application Engineer

UniString Tech Solutions

Hyderabad

Release Date : 20th July 2010

Version : 2.1

Document No : UTS-MC-KIT-M7.1.1-Man-

01

www.unistring.com

NOTE

(1) Please ensure that the C drive has enough disk space, preferably more than 1 GB so

that PSoC related software work properly.

(2) In addition to this user manual you can refer to the data sheet and programmer’s

guide of PSoC Designer tools which are present in CD.

(3) Contact [email protected] for any help pertaining to the experiments given in

this book.

(4) UTS maintain transparency in giving the original documentation/details offered by the OEM of the board. The original design of the boards and chips are covered under the copyrights of respective manufacturers. UTS claims rights only on the additional IP (experiments and code) offered along with the board under the acts of copyright.

(5) Disclaimer: UTS does not take any responsibility to any kind of consequences

related to damage or loss of design/product/project, which are directly or indirectly implied by the experiments in this book let.

www.unistring.com

CONTENTS

CYCLE 1: 8051 Microcontrollers

1. Serial Data Transmission using 8051 microcontroller in different

modes.

a. Serial data transmission and reception using polling mode

b. Serial data transmission and reception using interrupt mode

c. Implementing the modes of serial port using SM bits for

achieving baud rates using Timers

2. Look up tables for 8051.

a. Implementing the SIN look up table for 8051

3. Timing subroutines for 8051- Real time times and Applications.

a. Implementing the real time interrupt generation using timers

b. Program delay measurement using timers on 8051

4. Keyboard interface to 8051.

a. 4x4 Keyboard interface using serial protocol

5. ADC, DAC interface to 8051.

a. Interfacing ADC and collecting the sampled data in real

time

b. Generating the SIN wave using DAC and SIN look up tables.

6. LCD interface to 8051.

a. LCD interfacing to 8051 microcontroller

www.unistring.com

www.unistring.com

Overview

UTS-MC-KIT-M7.1 is next version of the UTS-MC-KIT-M5 with placement

modification in chips and functionally it same as M5 board. UTS-MC-KIT-M7.1 is

high end efficient and versatile controller module built with Phillips Microcontroller

P89V51RD2. This controller module can be used for wide range of applications right

from simple traffic light controller to lift controller, data logger’s applications and

many.

The UTS-MC-KIT-M7.1 has got P89V51RD2 microcontroller which has got

64Kilo Bytes of on chip Flash memory and 1 Kilo Bytes of RAM. The kit is has got

on board 11.0592MHz crystal for generating the on chip clock of 11.0592MHz.

A Key feature of the board is it has got so many interfaces with different on

board peripherals and has got expansion capability to add any further sensor and

peripherals in future. This prototype board is very easy to use for 8051 architecture.

This board is interfaced LED, 7 SEG DISPLAY, and dipswitch, pushbutton. This

Board is also having serial communication with pc through hyper terminal. The LCD

display can connect easily through connectors. No soldering work /No lose contact/

just insert burg stick connecter.

The most important feature of this board is it has got in system Programmable

feature, where this feature allows programming the microcontroller from PC through

the serial port link. So this avoids the extra requirement of the programmer device for

programming the microcontroller and development cycle also improves as it does not

require to pull out the microcontroller chip for programming for every programming

iteration.

The board has got on chip peripherals like on board 32 KB bytes of RAM,

Eight Light Emitting Diodes, four Push Buttons, Four Seven Segment Displays, 16X2

Liquid Crystal Character Display(LCD), Analog to Digital Converter, steeper motor

interface, Real time clock, RS-232 serial interface.

Requirements

www.unistring.com

The UTS-MC-KIT-M7.1 kit requires 12V power adaptor, serial cable for connecting

to PC. And few connecting cables. In the PC you should install the Kiel evaluation

Software.

Software is required for writing the application in C/Assembly language, compiling

and finally for generation of the hex file for downloading into the microcontroller.

Make sure you have satisfied the below hardware software requirements:-

Hardware Rquirements :

1. UTS-MC-KIT-M7.1

2. A serial cable , 9 pin cable wired one to one from female connector to male

connector

3. PC with serial port

4. 5V adaptor

5. Multimeter

6. DAC R-2R Ladder network.

7. Connecting Wires.

Software Rquirements :

1. UTS EDS or Keil evaluation software

2. Flash Magic tool.

Connecting UTS-MC-KIT-M7.1

1. Connect supplied serial port cable to external serial port jack(RS-232 jack) on

the PC back side

2. Connect the power supply adaptor to power supply adaptor socket (CN3

connector) on the board.

www.unistring.com

3. The serial port allows you to download the hex files into the microcontroller

thorough the flash magic tool from the PC.

4. Press the RESET switch and Click Start button in Flash Magic tool. After 1

sec a pop window getting as show in below picture. Then release the RESET

Button.

5.

6. After downloading the hex file press the RESET Switch. Then downloaded

application will be running.

Jumper, Connectors & Switch Settings on the Board

www.unistring.com

BLOCK DIAGRAM

P

8

9

V5

1

R

D

2

L

C

D

A

D

C0

804

Stepper motor driver

MemoryRTCBattery

Serial Port

Connector

MAX232

7

S

E

G

M

E

N

T

D

I

S

P

L

A

y

7 SEG INPUT

A B C D E F G De

c

CN2CN1

7 SEG control

POWER JACK

POWER SECTION

P1

P3 P

2P

0

RESET

SWITCH

CN4

L

E

D

P

O

R

T

CN6

4X4 MATRIX

KEYBOARD

12V

GND

5V

PUSH BOTTON SWITCH

CN9

CN10

CN13

ADC INPUT

CN1 and CN2 Connectors

a. The Seven segment display in common cathode configuration.

www.unistring.com

CN1

CN2

b. The CN1 are & input segment lines CN2 is the control lines.

POT setting on the boards

1. LCD CONTRAST.

a. LCD intensity Adjust POT. Location near to LCD. Adjust the POT till

Text/Squares appear on the display

2. ADC POT

a. Location near to the ADC chip

b. Adjusts the reference voltage to Analog to Digital Converter (ADC).

Adjust the POT R10 and observe the voltage at Pin 9 of U9 IC, i.e.

ADC0804. The reference value can be varied from 0 to 2.5Volts by

varying the POT.

Component Description

Microcontroller

The P89V51RD2 device contains a non-volatile 64KB Flash program

www.unistring.com

memory. In-System Programming (ISP) allows the user to download new code while

the microcontroller sits in the application. A default serial loader (boot loader)

program in ROM allows serial In-System programming of the Flash memory via the

UART without the need for a loader in the Flash code.

This device executes one machine cycle in 6 clock cycles, hence providing

twice the speed of a conventional 80C51. An OTP configuration bit lets the user select

conventional 12 clock timing if desired.

This device is a Single-Chip 8-Bit Micro controller manufactured in advanced

CMOS process and is a derivative of the 80C51 micro controller family. The

instruction set is 100% compatible with the 80C51 instruction set.

The device also has four 8-bit I/O ports, three 16-bit timer/event counters, a

multi-source, and four-priority-level, nested interrupt structure, an enhanced UART

and on-chip oscillator and timing circuits.

The added features of the P89V51RD2 makes it a powerful micro controller

for applications that require pulse width modulation, high-speed I/O and up/down

counting capabilities such as motor control.

Features:

• 80C51 Central Processing Unit

• On-chip Flash Program Memory with In-System Programming (ISP)

• Boot ROM contains low level Flash programming routines for downloading

via the UART

• Can be programmed by the end-user application (IAP)

• Six clocks per machine cycle operation (standard)

• 12 clocks per machine cycle operation (optional)

• Speed up to 20 MHz with 6 clock cycles per machine cycle (40 MHz

equivalent performance); up to 33 MHz with 12 clocks per machine cycle

• Fully static operation

• RAM expandable externally to 64 k bytes

• Four interrupt priority levels

• Seven interrupt sources

• Four 8-bit I/O ports

• Full-duplex enhanced UART

www.unistring.com

• Framing error detection

• Automatic address recognition

• Power control modes

• Clock can be stopped and resumed

• Idle mode

• Power down mode

• Programmable clock out

• Second DPTR register

• Asynchronous port reset

• Low EMI (inhibit ALE)

• Programmable Counter Array (PCA)

• PWM

• Capture/compare

RAM:

The CY62256 is a high-performance CMOS static RAM organized as 32K words by

8 bits. Easy memory expansion is provided by an active LOW chip enable (CE) and

active LOW output enable (OE) and three-state drivers. This device has an

automatic power-down feature, reducing the power consumption by 99.9% when

deselected. An active LOW write enable signal (WE) controls the writing/reading

operation of the memory. When CE and WE inputs are both LOW, data on the eight

data input/output pins(I/O0 through I/O7) is written into the memory location

addressed by the address present on the address pins (A0 through A14). Reading the

device is accomplished by selecting the device and enabling the outputs, CE and OE

active LOW, while WE remain inactive or HIGH. Under these conditions, the

contents of the location addressed by the information on address pins are present on

the eight data input/output pins. The input/output pins remain in a high-impedance

state unless the chip is selected, outputs are enabled, and write enable.

Features

• Temperature Ranges

—Commercial: 0°C to 70°C

www.unistring.com

• High speed: Access time 70 ns

• Voltage range: 4.5V–5.5V operation

• Low active power (70 ns, LL version, Com’l and Ind’l)

—275 mW (max.)

• Low standby power (70 ns, LL version, Com’l and Ind’l)

—28 µW (max.)

• Easy memory expansion with CE and OE features

• TTL-compatible inputs and outputs

• Automatic power-down when deselected

• CMOS for optimum speed/power

• Package : 600-mil 28-lead PDIP packages

RS-232 Interface

Standard serial interfacing of microcontroller (TTL) with PC or any RS-232 standard

device, requires TTL to RS-232 level converter. A MAX232 is used for this purpose.

It provides 2-channel RS-232 port and requires external 10uf capacitor.

• The driver requires a single supply of +5v.

• MAX232 includes a charge pump. which generates +10v and -10v from a

single 5v supply.

www.unistring.com

The Seven-Segment LED

One common requirement for many different digital devices is a visual

numeric display. Individual LEDs can of course display the binary states of a set

of latches or flip-flops. However, we're far more used to thinking and dealing with

decimal numbers. To this end, we want a display of some kind that can clearly

represent decimal numbers without any requirement of translating binary to

decimal or any other format.

This requires just seven LEDs (plus an eighth one for the decimal

point, if that is needed). A common technique is to use a shaped piece of

translucent plastic to operate as a specialized optical fiber, to distribute the light

from the LED evenly over a fixed bar shape. The seven bars are laid out as a

squared-off figure "8". The result is known as a seven-segment LED.

We've all seen seven-segment displays in a wide range of

applications. Clocks, watches, digital instruments, and many household appliances

already have such displays.

The illustration to the right shows the basic layout of the segments in a

www.unistring.com

seven-segment display. The segments themselves are identified with lower-case

letters "a" through "g," with segment "a" at the top and then counting clockwise.

Segment "g" is the center bar.

Most seven-segment digits also include a decimal point ("dp"), and

some also include an extra triangle to turn the decimal point into a comma. This

improves readability of large numbers on a calculator, for example. The decimal

point is shown here on the right, but some display units put it on the left, or have a

decimal point on each side.

Led displays are

• power-hungry(10ma per led)

• pin-hungry(8-pins per 7-segment display)

• 7-SEG displays are available in two types.

1.common anode

2.common cathode

www.unistring.com

The UTS-MC-KIT-M7.1 comes with common anode type. There are two seven

segment displays are connected to 8255_2 port B & C. The hex code for displaying

the corresponding values is given in below table. The corresponding hexadecimal

values has to be written on the corresponding ports of the 8255 for displaying on the

seven segment display.

Values to Be displayed on

Seven Segment Display

Value to be sent to

Seven segment display

(In Hexdecimal)

0 0x40

1 0x79

2 0x24

3 0x30

4 0x19

5 0x12

6 0x02

7 0x78

8 0x00

9 0x18

A 0x08

B 0x03

C 0x46

D 0x21

E 0x06

F 0x0E

Table : Seven Segment Decoding Values

www.unistring.com

LCD INTERFACE

LCD in 4 Bit Mode:

Till now whatever we discussed in the previous part of ths LCD tutorial, we were

dealing with 8-bit mode. Now we are going to learn how to use LCD in 4-bit mode.

There are many reasons why sometime we prefer to use LCD in 4-bit mode instead of

8-bit. One basic reason is lesser number of pins are needed to interface LCD.

In 4-bit mode the data is sent in nibbles, first we send the higher nibble and then the

lower nibble. To enable the 4-bit mode of LCD, we need to follow special sequence

of initialization that tells the LCD controller that user has selected 4-bit mode of

operation. We call this special sequence as resetting the LCD. Following is the reset

sequence of LCD.

� Wait for abour 20mS

� Send the first init value (0x03)

� Wait for about 10mS

� Send second init value (0x03)

� Wait for about 1mS

� Send third init value (0x03)

� Wait for 1mS

� Select bus width (0x03 - for 8-bit and 0x20 for 4-bit)

� Wait for 1mS

The busy flag will only be valid after the above reset sequence. Usually we do not use

busy flag in 4-bit mode as we have to write code for reading two nibbles from the

LCD. Instead we simply put a certain ammount of delay usually 300 to 600uS. This

delay might vary depending on the LCD you are using, as you might have a different

crystal frequency on which LCD controller is running. So it actually depends on the

LCD module you are using. So if you feel any problem running the LCD, simply try

to increase the delay. This usually works. For me about 400uS works perfect.

www.unistring.com

►LCD connections in 4-bit Mode

Above is the connection diagram of LCD in 4-bit mode, where we only need 6 pins to

interface an LCD. D4-D7 are the data pins connection and Enable and Register select

are for LCD control pins. We are not using Read/Write (RW) Pin of the LCD, as we

are only writing on the LCD so we have made it grounded permanently. If you want

to use it.. then you may connect it on your controller but that will only increase

another pin and does not make any big difference. Potentiometer RV1 is used to

control the LCD contrast. The unwanted data pins of LCD i.e. D0-D3 are connected

to ground.

►Sending data/command in 4-bit Mode

We will now look into the common steps to send data/command to LCD when

working in 4-bit mode. As i already explained in 4-bit mode data is sent nibble by

nibble, first we send higher nibble and then lower nibble. This means in both

command and data sending function we need to saperate the higher 4-bits and lower

4-bits.

www.unistring.com

The common steps are:

� Mask lower 4-bits

� Send to the LCD port

� Send enable signal

� Mask higher 4-bits

� Send to LCD port

� Send enable signal

We are done with the theory part now, In the next section we will take a look at the

programming microcontroller to control LCD in 4-bit mode.

Analog To Digital Convertor (ADC)

The ADC0804 is CMOS 8-Bit, successive approximation A/D converters

which use a modified potentiometric ladder and are designed to operate with the

processors/microcontrollers control bus via three-state outputs. These converters

appear to the processor as memory locations or I/O ports, and hence no interfacing

logic is required. The differential analog voltage input has good common- mode-

rejection and permits offsetting the analog zero-input voltage value. In addition, the

voltage reference input can be adjusted to allow encoding any smaller analog voltage

span to the full 8 bits of resolution.

Features:

• Compatible with 8051 µc derivatives-no interfacing logic needed - access time - 135

ns

• Easy interface to all microprocessors, or operates "stand alone"

• Differential analog voltage inputs Conversion Time <100µs

www.unistring.com

• Logic inputs and outputs meet both MOS and TTL voltage level specifications

• Works with 2.5V (LM336) voltage reference

• On-chip clock generator

• 0V to 5V analog input voltage range with single 5V supply

• No zero adjust required

• 0.3[Prime] standard width 20-pin DIP package

• 20-pin molded chip carrier or small outline package

• Operates ratiometrically or with 5 VDC, 2.5 VDC, or analog span adjusted voltage

reference

PIN DIAGRAM:

Pin Number Description

1 CS - Chip Select (Active Low)

2 RD - Read (Active Low)

3 WR - Write (Active Low)

4 CLK IN - Clock IN

5 INTR - Interrupt (Active Low)

www.unistring.com

6 Vin+ - Analog Voltage Input

7 Vin- - Analog Voltage Input

8 AGND - Analog Ground

9 Vref/2 - Voltage Reference / 2

10 DGND - Digital Ground

11 DB7 - Data Bit 7 (MSB)

12 DB6 - Data Bit 6

13 DB5 - Data Bit 5

14 DB4 - Data Bit 4

15 DB3 - Data Bit 3

16 DB2 - Data Bit 2

17 DB1 - Data Bit 1

18 DB0 - Data Bit 0 (LSB)

19 CLKR - Clock Reset

20 Vcc - Positive Supply or Vref

Temperature Sensor Interfacing to Microcontroller using

ADC804:

The ADC804 has 8-bit resolution with a maximum of 256 steps and the LM35

temperature sensor provides 10mV for every degree of temperature change.

We shall do Calibration such that for temperature range of 0 to 100 C, Voltage in at

input of ADC will be 0 to 2.56 v.

we need to set Vref/2 = 1.28V

so step size will be 2560mv/256 = 10mv also for every degree change in

temp. LM35 output changesby10mv ,so every degree change in temp. will produce 1

unit change in digital out of ADC

Thus resolution of our system will be 1deg C , which is Smallest temp. that we can

measure with this system. If resolution to be with 0.5deg C the Vref value to be

adjusted to 0.64V.

The Vref voltage can be adjusted varying the POT R10.

R10 POT

www.unistring.com

a. Location near to the ADC chip

b. Adjusts the reference voltage to Analog to Digital Convertor (ADC).

Adjust the POT R10 and observe the voltage at Pin 9 (i.e Vref Pin of

the ADC) of U9 IC, i.e ADC0804. The reference value can be varied

from 0 to 2.5Volts by varying the POT.

Sending parallel data as either four or eight bits are the two primary modes of

operation. While there are secondary considerations and modes, deciding how to send

the data to the LCD is most critical decision to be made for an LCD interface

application. Eight bit mode is best used when speed is required in an application and

at least ten I/O pins are available. Four bit mode requires a minimum of six bits. To

wire a microcontroller to an LCD in four bit mode, just the top four bits (DB4-7) are

written to.

The "R/S" bit is used to select whether data or an instruction is being

transferred between the microcontroller and the LCD. If the Bit is set, then the byte at

the current LCD "Cursor" Position can be read or written. When the Bit is reset, either

an instruction is being sent to the LCD or the execution status of the last instruction is

read back (whether or not it has completed).

The different instructions available for use LCD are shown in below:

1. Clear display

2. Return home

www.unistring.com

4. Decrement cursor

6. Increment cursor

5. Shift display right

6. Increment cursor.

7. Shift display left

8. Display off,Cursor off

A. Display off,Cursor on

C. Display on,Cursor off

E. Display on Cursor blinking on

F. Display on Cursor blinking off

10. Shift cursor position to left

14. Shift cursor position to right

18. Shift the entire display to the left

1C. Shift the entire display to the right

80. Force cursor to beginning of 1st line

C0. Force cursor to beginning of 2nd

line

38. 2 lines and 5x7 matrix

For further in detail description of the registers can go through the Data

sheet of 16X2 character LCD display.

Before you can send commands or data to the LCD module, the Module must be

initialized

LEDS

There are eight LEDs on the board from L0 to L7 for displaying eight bit information.

L0 is LSB and L7 is MSB. These eight LEDs are connected to CN4. so by connecting

any of the PORT to this CN4 and can write on to LEDs. The LEDS are connected in

common cathode fashion. So the data written on Port will be displayed with LEDs

indication directly.

www.unistring.com

PUSH Buttons

There are Four pushbuttons are available in the Kit named as SW1 to PSB4. These

push buttons are connected to CN9 on the Board.

www.unistring.com

Experimental Procedure For LAB

www.unistring.com

1. Serial Data Transmission using 8051 microcontroller in

different modes.

Aim: Write a program for serial communication using RS232 interface and communicate with PC using polling mode.

Introduction: In this experiment a program is written in C language to read data from PC

and the same data is echoed back to the computer through RS232 interface

available on the board.

The program flow chart • Write a program for serial communication using polling method. • Compile the program and generate Hex file. • The generated hex file will be downloaded in to the MC and

verify the result. KIEL software is used for compilation of C files and the hex file can be generated.

Experimental procedure: Step1: Open the Kiel ide and you can see a menu as shown in the figure.

www.unistring.com

Step 2:

To create a new project just click the project menu and click new

micro vision project , as shown in below figure.

www.unistring.com

Step 3:

Then a dialog box will be opened to give the destination as shown in

the figure. You can give the destination folder and save it.

www.unistring.com

Step 4:

To write a c file click the file menu and select the new document. The

desired code is written in the document. And this document is needed

to be added to the project.

Step 5:

In the project window on the left hand side you can see a project

window .in the window a folder called target can be seen to that

folder another folder can be seen as target source group1. the c file

which is written needed to be added to that folder . to add a c file to

that folder right click the source group1 folder and a menu will be

appeared as shown in the figure.

www.unistring.com

From that menu you can see add files to source group option. If you

click that option the c file will be added to the project.

Step 6:

Before building the project some settings are to made, from the main

menu click the flash, you can see the option as configure flash tools .

You click that option you can find a menu as shown in the figure.

www.unistring.com

From that menu click output and select an option called create hex

file. And in the target menu give the oscillator frequency as 11.0592.

Step 7:

Now all the hard work we have done to build the project and to

create the hex file

From the main menu select the project and in that an option called

build target can be seen , just click that . if all the coding is correct and

the syntaxes are correct an hex file will be generated.

Down loading the hex file to the target:

� Open the Flash Magic tool for downloading into the

Microcontroller Board. Click on Device menu select option you

will be popped up with a window named choose device. Under

choose device options select 8051 and click on Ok button to

open flash magic tool to download the hex file in to the MC and

is as shown below.

www.unistring.com

(1) Flash Magic Opens as shown in the figure

� Change setting for Flash Magic as shown in the above figure COM Port � Choose the Appropriate COM Port of the

computer. Generally it is COM1

Baud Rate � 9600

Device � 89V51RD2

Interface� None(ISP)

Oscillator Freq (MHZ) � 11.0592

Tick Erase All Flash+Security+Clks

Tick Verify after Programming

Now Goto

Option-> Advanced Options → Hardware Configuration

and uncheck the “Use DTR To Control Reset” as shown in the

figure below

www.unistring.com

� Browse for Hex file to be downloaded into the microcontroller

� Select the SERIAL. Hex file from the Folder in which SERIAL.c file is

located.

� Turn On the Board Power. The RUN/PROG button can be any

where (as 89V51RD2)

� Connect the serial port to Board from Computer

� Press and hold the reset button on board and press start button

on flash magic. wait until a small window comes with message

"Reset The Device Into ISP Mode "comes.

Once this window comes release the reset button.

� You can see the messages in flash magic tool as Erasing the

Device, Programming the Device ,Verifying and Finished

� (10)Once you get finished message in the flash magic. press

reset once to enter in run mode.

www.unistring.com

Results/Output verification: Now serial communication program is

running on Microcontroller. Open flash magic tool and under tools

menu click on terminal as shown below.

A window will be popped up and select the following settings as done

in the previous program .

You can observe a black window appearing having two parts. One is

output and another one is input to communicate to the serial port.

www.unistring.com

Press reset button and you can see a message saying “press any key”

under output pane. Now what ever the message you type at input

pane, the same message will be displayed on the output pane.

www.unistring.com

C SOURCE CODE

// This program reads the character from serial port and retransmits the

same back to PC

# include <reg51.h> /* define 8051 registers */

void SendChar(unsigned char x);

void DisplayMesPC(unsigned char *);

unsigned char *mes;

void main (void) { /* main program */

unsigned char temp;

TMOD = 0x20; /* GATE OFF,C/# T = 0, M1 M0 = 10(8 BIT AUTO RELOAD) TIMER 0 ,TIMER 1 IN

MODE 2(AUTO RELOAD MODE)*/

SCON = 0x50; /* SERIAL PORT IN MODE2 8-BIT UART VARIABLE BAUDRATE */

TH1 = 0xfd; /* TIMER 1 FOR BAUD RATE GEN(9.6K)*/

TR1 = 1; /* baud rate timer start*/

mes = "\r\nSerial data transmission and reception using polling

mode\r\n";

DisplayMesPC(mes);

mes = "\r\nPress Any Key\r\n";

DisplayMesPC(mes);

while (1)

{

while (!RI); // waiting for character from PC

temp = SBUF;// reading the character into temp variable from

Serial Buffer

RI = 0; // Resetting the Receive Flag

SendChar(temp); // Calling function for retransmitting the character back

to PC

}

}

www.unistring.com

void SendChar(unsigned char x) // transmit function to send

character to PC

{

SBUF =x; // wrting the character into the serial buffer

TI = 0; // Clearing the Transmit empty flag

while(!TI); // wating for end of trasmission. after transmission the TI flag will set.

}

void DisplayMesPC(unsigned char *mes)

{

int counter;

for (counter=0;mes[counter]!='\0';counter++)

{

SendChar(mes[counter]);

}

}

HARWARE CONFIGURATION

To test the board

Power supply cable should be connected to the M7 Board and serial

cable must be connected to the computer. Now go to the start menu

and in that go to the all programs menu . in that go to the accessories ,

there in the sub menu you will find a menu called communications. In

the communications menu select the hyper terminal.

After doing so the following window will be appeared. Enter any

connection name in block.

www.unistring.com

Select COM1 and then click ok

www.unistring.com

In that select the new connection and set the options as

Restore Defaults.

This will keep the default baud rate as 9600,1 start bit,1 stop bit and

hardware as none.

www.unistring.com

To check the output now, if any key is pressed from the keyboard that

will be displayed on the hyper terminal.

Basic Theory of 8051 Serial commutations UART (Universal Asynchronous Receiver and Transmitter)

One of the microcontroller features making it so powerful is an integrated

UART, better known as a serial port. It is a full-duplex port, thus being able to

transmit and receive data simultaneously and at different baud rates. Without

it, serial data send and receive would be an enormously complicated part of

the program in which the pin state is constantly changed and checked at

regular intervals. When using UART, all the programmer has to do is to simply

select serial port mode and baud rate. When it's done, serial data transmit is

nothing but writing to the SBUF register, while data receive represents

reading the same register. The microcontroller takes care of not making any

error during data transmission.

Serial port must be configured prior to being used. In other words, it is

necessary to determine how many bits is contained in one serial “word”, baud

rate and synchronization clock source. The whole process is in control of the

bits of the SCON register (Serial Control).

Serial Port Control (SCON) Register

SM0 - Serial port mode bit 0 is used for serial port mode selection.

www.unistring.com

SM1 - Serial port mode bit 1.

SM2 - Serial port mode 2 bit, also known as multiprocessor communication

enable bit. When set, it enables multiprocessor communication in mode 2 and

3, and eventually mode 1. It should be cleared in mode 0.

REN - Reception Enable bit enables serial reception when set. When cleared,

serial reception is disabled.

TB8 - Transmitter bit 8. Since all registers are 8-bit wide, this bit solves the

problem of transmitting the 9th bit in modes 2 and 3. It is set to transmit a

logic 1 in the 9th bit.

RB8 - Receiver bit 8 or the 9th bit received in modes 2 and 3. Cleared by

hardware if 9th bit received is a logic 0. Set by hardware if 9th bit received is a

logic 1.

TI - Transmit Interrupt flag is automatically set at the moment the last bit of

one byte is sent. It's a signal to the processor that the line is available for a

new byte transmit. It must be cleared from within the software.

RI - Receive Interrupt flag is automatically set upon one byte receive. It

signals that byte is received and should be read quickly prior to being

replaced by a new data. This bit is also cleared from within the software.

As seen, serial port mode is selected by combining the SM0 and SM2 bits:

SM0 SM1 Mode Description Baud Rate

0 0 0 8-bit Shift

Register 1/12 the quartz frequency

0 1 1 8-bit UART Determined by the timer 1

1 0 2 9-bit UART 1/32 the quartz frequency (1/64 the quartz

frequency)

1 1 3 9-bit UART Determined by the timer 1

www.unistring.com

In mode 0, serial data are transmitted and received through the RXD pin,

while the TXD pin output clocks. The bout rate is fixed at 1/12 the oscillator

frequency. On transmit, the least significant bit (LSB bit) is sent/received first.

TRANSMIT - Data transmit is initiated by writing data to the SBUF register. In

fact, this process starts after any instruction being performed upon this

register. When all 8 bits have been sent, the TI bit of the SCON register is

automatically set.

RECEIVE - Data receive through the RXD pin starts upon the two following

conditions are met: bit REN=1 and RI=0 (both of them are stored in the SCON

register). When all 8 bits have been received, the RI bit of the SCON register

is automatically set indicating that one byte receive is complete.

www.unistring.com

Since there are no START and STOP bits or any other bit except data sent

from the SBUF register in the pulse sequence, this mode is mainly used when

the distance between devices is short, noise is minimized and operating

speed is of importance. A typical example is I/O port expansion by adding a

cheap IC (shift registers 74HC595, 74HC597 and similar).

Mode 1

In mode 1, 10 bits are transmitted through the TXD pin or received through

the RXD pin in the following manner: a START bit (always 0), 8 data bits (LSB

first) and a STOP bit (always 1). The START bit is only used to initiate data

receive, while the STOP bit is automatically written to the RB8 bit of the

SCON register.

www.unistring.com

TRANSMIT - Data transmit is initiated by writing data to the SBUF register.

End of data transmission is indicated by setting the TI bit of the SCON

register.

RECEIVE - The START bit (logic zero (0)) on the RXD pin initiates data

receive. The following two conditions must be met: bit REN=1 and bit RI=0.

Both of them are stored in the SCON register. The RI bit is automatically set

upon data reception is complete.

The Baud rate in this mode is determined by the timer 1 overflow.

Mode 2

www.unistring.com

In mode 2, 11 bits are transmitted through the TXD pin or received through

the RXD pin: a START bit (always 0), 8 data bits (LSB first), a programmable

9th data bit and a STOP bit (always 1). On transmit, the 9th data bit is actually

the TB8 bit of the SCON register. This bit usually has a function of parity bit.

On receive, the 9th data bit goes into the RB8 bit of the same register

(SCON).The baud rate is either 1/32 or 1/64 the oscillator frequency.

TRANSMIT - Data transmit is initiated by writing data to the SBUF register.

End of data transmission is indicated by setting the TI bit of the SCON

register.

RECEIVE - The START bit (logic zero (0)) on the RXD pin initiates data

receive. The following two conditions must be met: bit REN=1 and bit RI=0.

Both of them are stored in the SCON register. The RI bit is automatically set

upon data reception is complete.

www.unistring.com

Mode 3

Mode 3 is the same as Mode 2 in all respects except the baud rate. The baud

rate in Mode 3 is variable.

The parity bit is the P bit of the PSW register. The simplest way to check

correctness of the received byte is to add a parity bit to it. Simply, before

initiating data transmit, the byte to transmit is stored in the accumulator and

the P bit goes into the TB8 bit in order to be “a part of the message”. The

procedure is opposite on receive, received byte is stored in the accumulator

and the P bit is compared with the RB8 bit. If they are the same- everything is

OK!

www.unistring.com

Baud Rate

Baud Rate is a number of sent/received bits per second. In case the UART is

used, baud rate depends on: selected mode, oscillator frequency and in some

cases on the state of the SMOD bit of the SCON register. All the necessary

formulas are specified in the table:

Baud Rate BitSMOD

Mode 0 Fosc. / 12

Mode 1 1 Fosc.

16 12 (256-TH1) BitSMOD

Mode 2 Fosc. / 32

Fosc. / 64

1

0

Mode 3 1 Fosc.

16 12 (256-TH1)

www.unistring.com

Timer 1 as a clock generator

Timer 1 is usually used as a clock generator as it enables various baud rates

to be easily set. The whole procedure is simple and is as follows:

First, enable Timer 1 overflow interrupt.

Configure Timer T1 to operate in auto-reload mode.

Depending on needs, select one of the standard values from the table and

write it to the TH1 register. That's all.

Fosc. (MHz) Baud Rate

11.0592 12 14.7456 16 20 Bit SMOD

150 40 h 30 h 00 h 0

300 A0 h 98 h 80 h 75 h 52 h 0

600 D0 h CC h C0 h BB h A9 h 0

1200 E8 h E6 h E0 h DE h D5 h 0

2400 F4 h F3 h F0 h EF h EA h 0

4800 F3 h EF h EF h 1

4800 FA h F8 h F5 h 0

9600 FD h FC h 0

9600 F5 h 1

19200 FD h FC h 1

38400 FE h 1

76800 FF h 1

www.unistring.com

Multiprocessor Communication

As you may know, additional 9th data bit is a part of message in mode 2 and

3. It can be used for checking data via parity bit. Another useful application of

this bit is in communication between two or more microcontrollers, i.e.

multiprocessor communication. This feature is enabled by setting the SM2 bit

of the SCON register. As a result, after receiving the STOP bit, indicating end

of the message, the serial port interrupt will be generated only if the bit RB8 =

1 (the 9th bit).

This is how it looks like in practice:

Suppose there are several microcontrollers sharing the same interface. Each

of them has its own address. An address byte differs from a data byte

because it has the 9th bit set (1), while this bit is cleared (0) in a data byte.

When the microcontroller A (master) wants to transmit a block of data to one

of several slaves, it first sends out an address byte which identifies the target

slave. An address byte will generate an interrupt in all slaves so that they can

examine the received byte and check whether it matches their address.

Of course, only one of them will match the address and immediately clear the

SM2 bit of the SCON register and prepare to receive the data byte to come.

Other slaves not being addressed leave their SM2 bit set ignoring the coming

data bytes.

www.unistring.com

www.unistring.com

Experiment – 1b

Write a program for serial communication using Interrupt

Aim: Write a program for serial communication using RS232 interface and communicate with PC using interrupt mode.

Introduction:

In this experiment a program is written in C language to read data from

PC and the same data is echoed back to the computer through RS232

interface available on the board.

The program flow chart

• Write a program for serial communication using interrupt

method.

• Compile the program and generate Hex file.

• The generated hex file will be downloaded in to the MC

and verify the result.

KIEL software is used for compilation of C files and the hex file can be

generated.

Experimental procedure:

Step1:

Open the kiel ide and you can see a menu as shoen in the figure.

www.unistring.com

Step 2:


microvision project , as shown in below figure.

www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:




which is written nedded to be added to that folder . to add a c file to



www.unistring.com



Step 6:

Before bulding the project some settings are to made, from the main


you click that option you can find a menu as shown in the figure.

www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com


� Select the switches.Hex file from the Folder in which switches.c

file is located.


where (as 89V51RD2)













www.unistring.com








www.unistring.com

C SOURCE CODE // This program reads the character from serial port and retransmits

the same back to PC

www.unistring.com




unsigned char *mes;

unsigned char isr=0,a;

void serial0() interrupt 4

{

if(RI==1)

{

isr=1;

a=SBUF;

RI=0;

SendChar(a);

}

}


TMOD = 0x20; /* GATE OFF,C/# T = 0, M1 M0 = 10(8 BIT AUTO RELOAD) TIMER 0

,TIMER 1 IN MODE 2(AUTO RELOAD MODE)*/




mes = "\r\nSerial data transmission and reception using interrupt

mode\r\n";

DisplayMesPC(mes);


DisplayMesPC(mes);

IE=0X90;IP=0X10; // ENABLING THE INTERRUPTS AND THE HIGH PRIORITY LEVEL IS

USED

while (1);

}


character to PC

{


www.unistring.com



}


{

int counter;


{


}

}


To test the board








www.unistring.com


www.unistring.com

In that select the new connection and set the options as restore to

defaults.


hardware as none.

www.unistring.com



Exercise:

1. Write a program for serial communication to PC and when a

character is sent to Microcontroller, it has to send the same character

two times.

2. Write a program for serial communication to PC and when a

character is sent to Microcontroller, the same character must be sent

back to PC but with case change (i.e. if a lower case character is sent

to microcontroller, upper case character must be sent to PC and vice

versa).

www.unistring.com

8051 Microcontroller Interrupts Theory

There are five interrupt sources for the 8051, which means that they can

recognize 5 different events that can interrupt regular program execution.

Each interrupt can be enabled or disabled by setting bits of the IE register.

Likewise, the whole interrupt system can be disabled by clearing the EA bit of

the same register. Refer to figure below.

Now, it is necessary to explain a few details referring to external interrupts-

INT0 and INT1. If the IT0 and IT1 bits of the TCON register are set, an

interrupt will be generated on high to low transition, i.e. on the falling pulse

edge (only in that moment). If these bits are cleared, an interrupt will be

continuously executed as far as the pins are held low.

www.unistring.com

IE Register (Interrupt Enable)

EA - global interrupt enable/disable:

0 - disables all interrupt requests.

1 - enables all individual interrupt requests.

ES - enables or disables serial interrupt:

0 - UART system cannot generate an interrupt.

1 - UART system enables an interrupt.

ET1 - bit enables or disables Timer 1 interrupt:

0 - Timer 1 cannot generate an interrupt.

1 - Timer 1 enables an interrupt.

EX1 - bit enables or disables external 1 interrupt:

0 - change of the pin INT0 logic state cannot generate an interrupt.

1 - enables an external interrupt on the pin INT0 state change.

ET0 - bit enables or disables timer 0 interrupt:

0 - Timer 0 cannot generate an interrupt.

1 - enables timer 0 interrupt.

EX0 - bit enables or disables external 0 interrupt:

0 - change of the INT1 pin logic state cannot generate an interrupt.

1 - enables an external interrupt on the pin INT1 state change.

Interrupt Priorities

It is not possible to foreseen when an interrupt request will arrive. If several

interrupts are enabled, it may happen that while one of them is in progress,

another one is requested. In order that the microcontroller knows whether to

continue operation or meet a new interrupt request, there is a priority list

instructing it what to do.

The priority list offers 3 levels of interrupt priority:

Reset! The apsolute master. When a reset request arrives, everything is

stopped and the microcontroller restarts.

Interrupt priority 1 can be disabled by Reset only.

www.unistring.com

Interrupt priority 0 can be disabled by both Reset and interrupt priority 1.

The IP Register (Interrupt Priority Register) specifies which one of existing

interrupt sources have higher and which one has lower priority. Interrupt

priority is usually specified at the beginning of the program. According to that,

there are several possibilities:

If an interrupt of higher priority arrives while an interrupt is in progress, it will

be immediately stopped and the higher priority interrupt will be executed first.

If two interrupt requests, at different priority levels, arrive at the same time

then the higher priority interrupt is serviced first.

If the both interrupt requests, at the same priority level, occur one after

another, the one which came later has to wait until routine being in progress

ends.

If two interrupt requests of equal priority arrive at the same time then the

interrupt to be serviced is selected according to the following priority list:

External interrupt INT0

Timer 0 interrupt

External Interrupt INT1

Timer 1 interrupt

Serial Communication Interrupt

www.unistring.com

IP Register (Interrupt Priority)

The IP register bits specify the priority level of each interrupt (high or low

priority).

PS - Serial Port Interrupt priority bit

Priority 0

Priority 1

PT1 - Timer 1 interrupt priority

Priority 0

Priority 1

PX1 - External Interrupt INT1 priority

Priority 0

Priority 1

PT0 - Timer 0 Interrupt Priority

Priority 0

Priority 1

PX0 - External Interrupt INT0 Priority

Priority 0

Priority 1

Handling Interrupt

When an interrupt request arrives the following occurs:

Instruction in progress is ended.

www.unistring.com

The address of the next instruction to execute is pushed on the stack.

Depending on which interrupt is requested, one of 5 vectors (addresses) is

written to the program counter in accordance to the table below:

Interrupt Source Vector (address)

IE0 3 h

TF0 B h

TF1 1B h

RI, TI 23 h

All addresses are in hexadecimal format

These addresses store appropriate subroutines processing interrupts. Instead

of them, there are usually jump instructions specifying locations on which

these subroutines reside.

When an interrupt routine is executed, the address of the next instruction to

execute is popped from the stack to the program counter and interrupted

program resumes operation from where it left off.

From the moment an interrupt is enabled, the microcontroller is on alert all the

time. When an interrupt request arrives, the program execution is stopped,

electronics recognizes the source and the program “jumps” to the appropriate

address (see the table above). This address usually stores a jump instruction

specifying the start of appropriate subroutine. Upon its execution, the program

resumes operation from where it left off.

www.unistring.com

Experiment – 1c

Serial communication with different Baud rates

Aim: Write a program for serial communication using RS232 interface and communicate with PC using different baud rates.

Introduction:

In this experiment a program is written in C language to read data from

PC and the same data is echoed back to the computer through RS232

interface available on the board.


• Write a program for serial communication with different

baud rates.





generated.


Step1:


www.unistring.com

Step 2:



www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:







www.unistring.com



Step 6:




www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com



file is located.


where (as 89V51RD2)













www.unistring.com








www.unistring.com

C SOURCE CODE

// This program reads the character from serial port and retransmits the

same back to PC


www.unistring.com

FUNCTION PROTOTYPE DECLARATION



void baudrate(unsigned int a,unsigned char mode);

VARIABLE DECLARATION

unsigned char *mes;

unsigned char isr=0,a;

INTERRUPT SERVICE ROUTINE

void serial0() interrupt 4

{

if(RI==1)

{

isr=1;

a=SBUF;

RI=0;

}

}

MAIN CODE STARTS HERE


baudrate(9600,1); // function for different baud rates


DisplayMesPC(mes);

while (1)

{

if(isr==1)

{

SendChar(a); // Calling function for retransmitting

the character back to PC

isr=0;

}

//-----------------------------------------SendChar(temp); // Calling

function for retransmitting the character back to PC

}

}

www.unistring.com

FUNCTION FOR SENDING A CHARACTER TO TX REGISTER


character to PC

{



while(!TI); // wating for end of trasmission. after transmission the TI

flag will set.

}

FUNCTION FOR SENDING A STRING TO TX REGISTER


{

int counter;


{


}

}

// VALUE FOR THE 1200 BAUD RATE IS 0XE8

// VALUE FOR THE 2400 BAUD RATE IS 0XF4

// VALUE FOR THE 4800 BAUD RATE IS 0XFA

// VALUE FOR THE 9600 BAUD RATE IS 0XFD

void baudrate(unsigned int a,unsigned char mode)

{

TMOD = 0x20; /* GATE OFF,C/# T = 0, M1 M0 = 10(8 BIT

AUTO RELOAD) TIMER 0 ,TIMER 1 IN MODE 2(AUTO RELOAD MODE)*/

SCON = 0x50; /* SERIAL PORT IN MODE2 8-BIT UART

VARIABLE BAUDRATE */

// TH1 = a; /* TIMER 1 FOR BAUD RATE GEN(9.6K)*/

if(mode==0)

{

PCON=0x00;

if(a==1200)

{

TH1=0xfd;

www.unistring.com

}

if(a==2400)

{

TH1=0xf4;

}

if(a==4800)

{

TH1=0xfa;

}

if(a==9600)

{

TH1=0xfd;

}

}

else if(mode==1)

{ PCON=0x80;

if(a==19200)

{

TH1=0xfd;

}

if(a==9600)

{

TH1=0xfa;

}

if(a==4800)

{

TH1=0xf4;

}

if(a==2400)

{

TH1=0xe8;

}

}


IE=0X90;IP=0X10; // ENABLING THE INTERRUPTS AND

THE HIGH PRIORITY LEVEL IS USED

}


To test the board




www.unistring.com






www.unistring.com

In that select the new connection and set the options with

programmed baud rate and select 1 start bit, 1 stop bit and hardware

as none.

www.unistring.com



www.unistring.com

2. Look up tables for 8051.

Experiment – 2a

Write a program for implementing a sin lookup table on 8051

Aim:

a. Write a program for Implementing the SIN look up table for 8051

Introduction: In this experiment a program is written in C language to read data from the

PC(The value of Sine from 0 to 90 degree) and the corresponding value of

SINE is displayed on the serial console of the PC.

The program flow chart • Write a program for implementing a SINE lookup table. • Compile the program and generate Hex file. • The generated hex file will be downloaded in to the MC and

verify the result. KIEL software is used for compilation of C files and the hex file can be generated.

Experimental procedure: Step1: Open the kiel ide and you can see a menu as shown in the figure.

www.unistring.com

Step 2: To create a new project just click the project menu and click new microvision project , as shown in below figure.

www.unistring.com

Step 3: Then a dialog box will be opened to give the destination as shown in the figure. You can give the destination folder and save it.

www.unistring.com

Step 4: To write a c file click the file menu and select the new document. The desired code is written in the document. And this document is needed to be added to the project. Step 5: In the project window on the left hand side you can see a project window .in the window a folder called target can be seen to that folder another folder can be seen as target source group1. the c file which is written nedded to be added to that folder . to add a c file to that folder right click the source group1 folder and a menu will be appeared as shown in the figure.

www.unistring.com

From that menu you can see add files to source group option. If you click that option the c file will be added to the project.

Step 6: Before bulding the project some settings are to made, from the main menu click the flash, you can see the option as configure flash tools . you click that option you can find a menu as shown in the figure.

www.unistring.com

From that menu click output and select an option called create hex file. And in the target menu give the oscillator frequency as 11.0592. Step 7: Now all the hard work we have done to build the project and to create the hex file From the main menu select the project and in that an option called build target can be seen , just click that . if all the coding is correct and the syntaxes are correct an hex file will be generated.


� Open the Flash Magic tool for downloading into the Microcontroller Board. Click on Device menu select option you will be popped up with a window named choose device. Under choose device options select 8051 and click on Ok button to open flash magic tool to download the hex file in to the MC and is as shown below.


www.unistring.com

� Change setting for Flash Magic as shown in the above figure COM Port Choose the Appropriate COM Port of the computer. Generally it is COM1 Baud Rate 9600 Device 89V51RD2 Interface None(ISP) Oscillator Freq (MHZ) 11.0592 Tick Erase All Flash+Security+Clks Tick Verify after Programming Now Goto Option-> Advanced Options → Hardware Configuration and uncheck the “Use DTR To Control Reset” as shown in the figure below

www.unistring.com

� Browse for Hex file to be downloaded into the microcontroller � Select the switches.Hex file from the Folder in which switches.c file is

located.

� Turn On the Board Power. The RUN/PROG button can be any where (as 89V51RD2)

� Connect the serial port to Board from Computer � Press and hold the reset button on board and press start button on

flash magic. wait until a small window comes with message "Reset The Device Into ISP Mode "comes. Once this window comes release the reset button.

� You can see the messages in flash magic tool as Erasing the Device, Programming the Device ,Verifying and Finished

� (10)Once you get finished message in the flash magic. press reset once to enter in run mode.

Results/Output verification: Now serial communication program is running on Microcontroller. Open flash magic tool and under tools menu click on terminal as shown below.

www.unistring.com

A window will be popped up and select the following settings as done in the previous program .

You can observe a black window appearing having two parts. One is output and another one is input to communicate to the serial port. Press reset button and you can see a message saying “press any key” under output pane. Now what ever the message you type at input pane, the same message will be displayed on the output pane.

www.unistring.com

C SOURCE CODE // This program reads the character from serial port and retransmits the same back to PC #include <reg51.h> /* define 8051 registers */ void SendChar(unsigned char x); void DisplayMesPC(unsigned char *); void check(unsigned char a,unsigned char b);

www.unistring.com

unsigned char *mes; unsigned char isr=0,r[5],len=0; unsigned char lookup[]={0,1,2,3,4,5,6,7,8}; void serial0() interrupt 4 { if(RI==1) { isr=1; r[len++]=SBUF; RI=0; } } void main (void) { /* main program */ TMOD = 0x20; /* GATE OFF,C/#T = 0, M1 M0 = 10(8 BIT AUTO RELOAD) TIMER 0 ,TIMER 1 IN MODE 2(AUTO RELOAD MODE)*/ SCON = 0x50; /* SERIAL PORT IN MODE2 8-BIT UART VARIABLE BAUDRATE */ TH1 = 0xfd; /* TIMER 1 FOR BAUD RATE GEN(9.6K)*/ TR1 = 1; /* baud rate timer start*/ SendChar(13);SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90)-->"; DisplayMesPC(mes); SendChar(13);SendChar(10); IE=0X90;IP=0X10; // ENABLING THE INTERRUPTS AND THE HIGH PRIORITY LEVEL IS USED len=0; isr=0; while (1) { if(len>=3) { if((r[len-2]=='0')&&(r[len-3]=='0')) { SendChar(13);SendChar(10); mes = "SIN 0 VALUE IS "; DisplayMesPC(mes);SendChar(' '); SendChar(lookup[0]+48); SendChar('.'); SendChar(lookup[0]+48); isr=0; len=0; SendChar(13); SendChar(10);

www.unistring.com

SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } else if((r[len-2]=='0')&&(r[len-3]=='3')) { SendChar(13);SendChar(10); mes = "SIN 30 VALUE IS -->"; DisplayMesPC(mes); SendChar(' '); SendChar(lookup[0]+48); SendChar('.'); SendChar(lookup[5]+48); isr=0; len=0; SendChar(13); SendChar(10); SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } else if((r[len-2]=='5')&&(r[len-3]=='4')) { SendChar(13); SendChar(10); mes = "SIN 45 VALUE IS -->"; DisplayMesPC(mes); SendChar(' '); SendChar(lookup[0]+48); SendChar('.'); SendChar(lookup[7]+48); SendChar(lookup[0]+48); isr=0; len=0; SendChar(13); SendChar(10); SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } else if((r[len-2]=='0')&&(r[len-3]=='6')){ SendChar(13);SendChar(10); mes = "SIN 60 VALUE IS -->";

www.unistring.com

DisplayMesPC(mes); SendChar(' '); SendChar(lookup[0]+48); SendChar('.'); SendChar(lookup[8]+48); SendChar(lookup[6]+48); isr=0; len=0; SendChar(13); SendChar(10); SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } else if((r[len-2]=='0')&&(r[len-3]=='9')){ SendChar(13); SendChar(10); mes = "SIN 90 VALUE IS -->"; DisplayMesPC(mes);SendChar(' '); SendChar(lookup[1]+48); isr=0; len=0; SendChar(13); SendChar(10); SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } else { SendChar(13);SendChar(10); mes = "TRY THE MENTIONED DEGREES"; DisplayMesPC(mes); SendChar(' '); isr=0;len=0; SendChar(13); SendChar(10); SendChar(13); SendChar(10); mes = "ENTER THE SIN VALUE IN DEGRESS(00,30,45,60,90) AND PRESS ENTER-->"; DisplayMesPC(mes); } }

www.unistring.com

} } void SendChar(unsigned char x) // transmit function to send character to PC { SBUF =x; // wrting the character into the serial buffer TI = 0; // Clearing the Transmit empty flag while(!TI); // wating for end of trasmission. after transmission the TI flag will set. } void DisplayMesPC(unsigned char *mes) { int counter; for (counter=0;mes[counter]!='\0';counter++) { SendChar(mes[counter]); } } Results/Discussion: After programming the code into the microcontroller just reset the microcontroller and put it in the rum mode. You can see the temperature value from the temperature sensor is shown on the lcd and the hyper terminal.

www.unistring.com

HARWARE CONFIGURATION To test the board Power supply cable should be connected to the M7 Board and serial cable must be connected to the computer. Now go to the start menu and in that go to the all programs menu . in that go to the accessories , there in the sub menu you will find a menu called communications. In the communications menu select the hyper terminal. After doing so the following window will be appeared. Enter any connection name in block.


www.unistring.com

In that select the new connection and set the options as restore to defaults. This will keep the default baud rate as 9600,1 start bit,1 stop bit and hardware as none.

www.unistring.com

To check the output now, if any key is pressed from the keyboard that will be displayed on the hyper terminal.

www.unistring.com

3. Timing subroutines for 8051- Real time times and Applications.

Experiment – 3a

Write a program for implementing the real time interrupt generation using

timers

Aim: Write a program for implementing the real time interrupt generation using timers

Introduction: In this experiment a program is written in C language to use the timer

as an interrupt generation and send a character when the timer is

runned out.


• Write a program for timer 0 interrupt generation.





generated.


Step1:


www.unistring.com

Step 2:



www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:







www.unistring.com



Step 6:




www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com



file is located.


where (as 89V51RD2)













www.unistring.com








www.unistring.com

C SOURCE CODE


void SendChar(unsigned char );

unsigned int count=0;

www.unistring.com

unsigned char usetimer=0,timeout=0;

void timer0 (void) interrupt 1 /* for start of conversion at every

second*/

{

TR0 = 0;

if(usetimer==1)

{

count--;

if(count==0)

{

timeout=1;

}

}

TL0 = 0xFD ;

TH0 = 0x4A;

TR0 = 1;

}


TMOD = 0x21;

TL0 = 0xFD ;

TH0 = 0x4A;

EA = 1; // Master Enable for Interrupts

ET0=1;

TR0 = 1;

count=20;

usetimer=1;

while(1)

{

if(timeout==1)

{ timeout=0;count=0;usetimer=0;

// TMOD = 0x22; /* GATE OFF,C/# T = 0, M1 M0 = 10(8 BIT AUTO RELOAD) TIMER 1

IN

MODE 2(AUTO RELOAD MODE)TIMER 0 in 16 bit mode*/




SendChar('A');

timeout=0;count=30;usetimer=1;

}

www.unistring.com

}

}


character to PC

{




}


To test the board








www.unistring.com


www.unistring.com


defaults.


hardware as none.

www.unistring.com

Results/Discussion

After programming the code in the microcontroller, the output can be

seen as when the timer is runned out an interrupt is generated by

showing a character is sent to the hyper terminal .

8051 Timers: As you already know, the microcontroller oscillator uses quartz crystal for its

operation. As the frequency of this oscillator is precisely defined and very

stable, pulses it generates are always of the same width, which makes them

ideal for time measurement. Such crystals are also used in quartz watches. In

order to measure time between two events it is sufficient to count up pulses

coming from this oscillator. That is exactly what the timer does. If the timer is

properly programmed, the value stored in its register will be incremented (or

decremented) with each coming pulse, i.e. once per each machine cycle. A

single machine-cycle instruction lasts for 12 quartz oscillator periods, which

means that by embedding quartz with oscillator frequency of 12MHz, a

number stored in the timer register will be changed million times per second,

i.e. each microsecond.

The 8051 microcontroller has 2 timers/counters called T0 and T1. As their

names suggest, their main purpose is to measure time and count external

events. Besides, they can be used for generating clock pulses to be used in

serial communication, so called Baud Rate.

Timer T0

As seen in figure below, the timer T0 consists of two registers – TH0 and TL0

representing a low and a high byte of one 16-digit binary number.

www.unistring.com

Accordingly, if the content of the timer T0 is equal to 0 (T0=0) then both

registers it consists of will contain 0. If the timer contains for example number

1000 (decimal), then the TH0 register (high byte) will contain the number 3,

while the TL0 register (low byte) will contain decimal number 232.

Formula used to calculate values in these two registers is very simple:

TH0 × 256 + TL0 = T

Matching the previous example it would be as follows:

3 × 256 + 232 = 1000

Since the timer T0 is virtually 16-bit register, the largest value it can store is

65 535. In case of exceeding this value, the timer will be automatically cleared

and counting starts from 0. This condition is called an overflow. Two registers

TMOD and TCON are closely connected to this timer and control its

operation.

TMOD Register (Timer Mode)

The TMOD register selects the operational mode of the timers T0 and T1. As

seen in figure below, the low 4 bits (bit0 - bit3) refer to the timer 0, while the

high 4 bits (bit4 - bit7) refer to the timer 1. There are 4 operational modes and

each of them is described herein.

www.unistring.com

Bits of this register have the following function:

GATE1 enables and disables Timer 1 by means of a signal brought to the

INT1 pin (P3.3):

1 - Timer 1 operates only if the INT1 bit is set.

0 - Timer 1 operates regardless of the logic state of the INT1 bit.

C/T1 selects pulses to be counted up by the timer/counter 1:

1 - Timer counts pulses brought to the T1 pin (P3.5).

0 - Timer counts pulses from internal oscillator.

T1M1,T1M0 These two bits select the operational mode of the Timer 1.

T1M1 T1M0 Mode Description

0 0 0 13-bit timer

0 1 1 16-bit timer

1 0 2 8-bit auto-reload

1 1 3 Split mode

GATE0 enables and disables Timer 1 using a signal brought to the INT0 pin

(P3.2):

1 - Timer 0 operates only if the INT0 bit is set.

0 - Timer 0 operates regardless of the logic state of the INT0 bit.

C/T0 selects pulses to be counted up by the timer/counter 0:

1 - Timer counts pulses brought to the T0 pin (P3.4).

0 - Timer counts pulses from internal oscillator.

T0M1,T0M0 These two bits select the oprtaional mode of the Timer 0.

T0M1 T0M0 Mode Description

0 0 0 13-bit timer

0 1 1 16-bit timer

1 0 2 8-bit auto-reload

1 1 3 Split mode

Timer 0 in mode 0 (13-bit timer)

This is one of the rarities being kept only for the purpose of compatibility with

the previuos versions of microcontrollers. This mode configures timer 0 as a

13-bit timer which consists of all 8 bits of TH0 and the lower 5 bits of TL0. As

a result, the Timer 0 uses only 13 of 16 bits. How does it operate? Each

www.unistring.com

coming pulse causes the lower register bits to change their states. After

receiving 32 pulses, this register is loaded and automatically cleared, while

the higher byte (TH0) is incremented by 1. This process is repeated until

registers count up 8192 pulses. After that, both registers are cleared and

counting starts from 0.

Timer 0 in mode 1 (16-bit timer)

Mode 1 configures timer 0 as a 16-bit timer comprising all the bits of both

registers TH0 and TL0. That's why this is one of the most commonly used

modes. Timer operates in the same way as in mode 0, with difference that the

registers count up to 65 536 as allowable by the 16 bits.

www.unistring.com

Timer 0 in mode 2 (Auto-Reload Timer)

Mode 2 configures timer 0 as an 8-bit timer. Actually, timer 0 uses only one 8-

bit register for counting and never counts from 0, but from an arbitrary value

(0-255) stored in another (TH0) register.

The following example shows the advantages of this mode. Suppose it is

necessary to constantly count up 55 pulses generated by the clock.

If mode 1 or mode 0 is used, It is necessary to write the number 200 to the

timer registers and constantly check whether an overflow has occurred, i.e.

whether they reached the value 255. When it happens, it is necessary to

rewrite the number 200 and repeat the whole procedure. The same procedure

is automatically performed by the microcontroller if set in mode 2. In fact, only

the TL0 register operates as a timer, while another (TH0) register stores the

value from which the counting starts. When the TL0 register is loaded, instead

of being cleared, the contents of TH0 will be reloaded to it. Referring to the

previous example, in order to register each 55th pulse, the best solution is to

write the number 200 to the TH0 register and configure the timer to operate in

mode 2.

www.unistring.com

Timer 0 in Mode 3 (Split Timer)

Mode 3 configures timer 0 so that registers TL0 and TH0 operate as separate

8-bit timers. In other words, the 16-bit timer consisting of two registers TH0

and TL0 is split into two independent 8-bit timers. This mode is provided for

applications requiring an additional 8-bit timer or counter. The TL0 timer turns

into timer 0, while the TH0 timer turns into timer 1. In addition, all the control

bits of 16-bit Timer 1 (consisting of the TH1 and TL1 register), now control the

8-bit Timer 1. Even though the 16-bit Timer 1 can still be configured to

operate in any of modes (mode 1, 2 or 3), it is no longer possible to disable it

as there is no control bit to do it. Thus, its operation is restricted when timer 0

is in mode 3.

www.unistring.com

The only application of this mode is when two timers are used and the 16-bit

Timer 1 the operation of which is out of control is used as a baud rate

generator.

Timer Control (TCON) Register

TCON register is also one of the registers whose bits are directly in control of

timer operation.

Only 4 bits of this register are used for this purpose, while rest of them is used

for interrupt control to be discussed later.

TF1 bit is automatically set on the Timer 1 overflow.

TR1 bit enables the Timer 1.

1 - Timer 1 is enabled.

0 - Timer 1 is disabled.

TF0 bit is automatically set on the Timer 0 overflow.

TR0 bit enables the timer 0.

1 - Timer 0 is enabled.

www.unistring.com

0 - Timer 0 is disabled.

How to use the Timer 0 ?

In order to use timer 0, it is first necessary to select it and configure the mode

of its operation. Bits of the TMOD register are in control of it:

Referring to figure above, the timer 0 operates in mode 1 and counts pulses

generated by internal clock the frequency of which is equal to 1/12 the quartz

frequency.

Turn on the timer:

The TR0 bit is set and the timer starts operation. If the quartz crystal with

frequency of 12MHz is embedded then its contents will be incremented every

microsecond. After 65.536 microseconds, the both registers the timer consists

of will be loaded. The microcontroller automatically clears them and the timer

www.unistring.com

keeps on repeating procedure from the beginning until the TR0 bit value is

logic zero (0).

How to 'read' a timer?

Depending on application, it is necessary either to read a number stored in

the timer registers or to register the moment they have been cleared.

- It is extremely simple to read a timer by using only one register configured in

mode 2 or 3. It is sufficient to read its state at any moment. That's all!

- It is somehow complicated to read a timer configured to operate in mode 2.

Suppose the lower byte is read first (TL0), then the higher byte (TH0). The

result is:

TH0 = 15 TL0 = 255

Everything seems to be ok, but the current state of the register at the moment

of reading was:

TH0 = 14 TL0 = 255

In case of negligence, such an error in counting (255 pulses) may occur for

not so obvious but quite logical reason. The lower byte is correctly read (255),

but at the moment the program counter was about to read the higher byte

TH0, an overflow occurred and the contents of both registers have been

changed (TH0: 14→15, TL0: 255→0). This problem has a simple solution.

The higher byte should be read first, then the lower byte and once again the

higher byte. If the number stored in the higher byte is different then this

sequence should be repeated. It's about a short loop consisting of only 3

instructions in the program.

There is another solution as well. It is sufficient to simply turn the timer off

while reading is going on (the TR0 bit of the TCON register should be

cleared), and turn it on again after reading is finished.

Timer 0 Overflow Detection

Usually, there is no need to constantly read timer registers. It is sufficient to

register the moment they are cleared, i.e. when counting starts from 0. This

condition is called an overflow. When it occurrs, the TF0 bit of the TCON

register will be automatically set. The state of this bit can be constantly

checked from within the program or by enabling an interrupt which will stop

the main program execution when this bit is set. Suppose it is necessary to

www.unistring.com

provide a program delay of 0.05 seconds (50 000 machine cycles), i.e. time

when the program seems to be stopped:

First a number to be written to the timer registers should be calculated:

Then it should be written to the timer registers TH0 and TL0:

When enabled, the timer will resume counting from this number. The state of

the TF0 bit, i.e. whether it is set, is checked from within the program. It

happens at the moment of overflow, i.e. after exactly 50.000 machine cycles

or 0.05 seconds.

How to measure pulse duration?

www.unistring.com

Suppose it is necessary to measure the duration of an operation, for example

how long a device has been turned on? Look again at the figure illustrating

the timer and pay attention to the function of the GATE0 bit of the TMOD

register. If it is cleared then the state of the P3.2 pin doesn't affect timer

operation. If GATE0 = 1 the timer will operate until the pin P3.2 is cleared.

Accordingly, if this pin is supplied with 5V through some external switch at the

moment the device is being turned on, the timer will measure duration of its

operation, which actually was the objective.

How to count up pulses?

Similarly to the previous example, the answer to this question again lies in the

TCON register. This time it's about the C/T0 bit. If the bit is cleared the timer

counts pulses generated by the internal oscillator, i.e. measures the time

passed. If the bit is set, the timer input is provided with pulses from the P3.4

pin (T0). Since these pulses are not always of the same width, the timer

cannot be used for time measurement and is turned into a counter, therefore.

The highest frequency that could be measured by such a counter is 1/24

frequency of used quartz-crystal.

Timer 1

www.unistring.com

Timer 1 is identical to timer 0, except for mode 3 which is a hold-count mode.

It means that they have the same function, their operation is controlled by the

same registers TMOD and TCON and both of them can operate in one out of

4 different modes.

www.unistring.com

Experiment – 3b

Write a program for implementing timer as a delay generator

Aim: Write a program for implementing the timer as a required various delay generator.

Introduction:

In this experiment a program is written in C language to use the timer

as an different delay generator.


• Write a program for timer 0 which is used as a delay

generator.





generated.


Step1:


www.unistring.com

Step 2:



www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:







www.unistring.com



Step 6:




www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com



file is located.


where (as 89V51RD2)













www.unistring.com








www.unistring.com

C SOURCE CODE


void SendChar(unsigned char );

www.unistring.com

void Send_Hex(unsigned char );


unsigned char *mes;

unsigned int count=0,count1=1;

unsigned char temp=0,temp1=0;


TMOD = 0x21;

TL0 = 0x00 ;

TH0 = 0x00;




ET0=1;

TR0 = 0;

mes = "\r\n\r\nProgram delay measurement using timers on

8051\r\n";

DisplayMesPC(mes);

while(count1<=7)

{

TL0 = 0x00 ;

TH0 = 0x00;

mes = "\r\n\r\n\r\nThe Default Timer Register values\r\n";

DisplayMesPC(mes);

mes = "\r\nTH0 | TL0 =";

DisplayMesPC(mes);

temp=TL0;

temp1=TH0;

Send_Hex(temp1);

Send_Hex(temp);

mes = "\r\n\r\nThe Programing is running....\r\n";

DisplayMesPC(mes);

TR0 =1;

while(count<count1){

SendChar('S');

count++;

}

TR0 = 0;

mes = "\r\n\r\nAfter Running program Timer Register values\r\n";

www.unistring.com

DisplayMesPC(mes);

mes = "\r\nTH0 | TL0 =";

DisplayMesPC(mes);

temp=TL0;

temp1=TH0;

Send_Hex(temp1);

Send_Hex(temp);

count=0;

count1++;

}

while(1);

}


character to PC

{




}


{

int counter;


{


}

}

void Send_Hex(unsigned char i){

char low,high;

low=i&0x0f;

high=(i&0xf0)>>4;

if( high>9)

SendChar(high+55);

www.unistring.com

else

SendChar(high+48);

if( low>9)

SendChar(low+55);

else

SendChar(low+48);

}


To test the board









www.unistring.com


defaults.


hardware as none.

www.unistring.com

Results/Discussion

After programming the code in the microcontroller, the output can be

seen as when the value in the count is passed say 1 for 1 sec and 2 for2

seconds .then the timer will work accordingly .so for according to

passing the value for the timer ,a character is sent for 1 second or 2

second and so on and the output will be sent to the hyper terminal.

www.unistring.com

4. Keyboard interface to 8051.

Experiment – 4a

Write a program for interfacing a keypad to the microcontroller

Aim: Write a program for interfacing a keypad to the microcontroller and the output is shown in the seven segment display when ever a key is pressed.

Introduction: In this experiment a program is written in C language to read data from the keypad

and the data is sent to the seven segment display on the board.


• Write a program for interfacing keypad and the output is shown in the

seven segment display when ever a key is pressed.


• The generated hex file will be downloaded in to the MC and verify the

result.

KIEL software is used for compilation of C files and the hex file can be generated.


Step1:

Open the kiel ide and you can see a menu as shown in the figure.

www.unistring.com

Step 2:

To create a new project just click the project menu and click new microvision project

, as shown in below figure.

www.unistring.com

Step 3:

Then a dialog box will be opened to give the destination as shown in the figure. You

can give the destination folder and save it.

www.unistring.com

Step 4:

To write a c file click the file menu and select the new document. The desired code is

written in the document. And this document is needed to be added to the project.

Step 5:

In the project window on the left hand side you can see a project window .in the

window a folder called target can be seen to that folder another folder can be seen as

target source group1. the c file which is written nedded to be added to that folder . to

add a c file to that folder right click the source group1 folder and a menu will be


www.unistring.com

From that menu you can see add files to source group option. If you click that

option the c file will be added to the project.

Step 6:

Before bulding the project some settings are to made, from the main menu click the

flash, you can see the option as configure flash tools . you click that option you can

find a menu as shown in the figure.

www.unistring.com

From that menu click output and select an option called create hex file. And in the

target menu give the oscillator frequency as 11.0592.

Step 7:

Now all the hard work we have done to build the project and to create the hex file

From the main menu select the project and in that an option called build target can be

seen , just click that . if all the coding is correct and the syntaxes are correct an hex

file will be generated.


Follow the same steps as mentioned in Ex 1-a for downloading the hex file

into the microcontroller

www.unistring.com

C SOURCE CODE

#include <reg51.h>

#include"lcd.h"

sbit R1 = P1^0;

sbit R2 = P1^1;

sbit R3 = P1^2;

sbit R4 = P1^3;

sbit C1 = P1^4;

sbit C2 = P1^5;

sbit C3 = P1^6;

sbit C4 = P1^7;

unsigned char key;

void Delay(unsigned int);

void delay()

{

unsigned int i;

for (i=0; i<10; i++); /* For 1 ms */

}

unsigned char READ_SWITCHES (void) // initialize the

port for inputs

{

// P1.0 to p1.3 are outpot; and P1.4 to P1.7 are inputs

// the keybad is connected to port 1

R4=1; // make all rows = 1

R3=1;

R2=1;

R1=0;

//test row 1

if (C1 == 0){ // key 1 is presed

delay(); //depounce

while (C1==0); //wait until release the key

return 1; //

}

if (C2 == 0){ //key 2 is pressed

delay(); //depounce

www.unistring.com


return 2;

}


delay(); //depounce


return 3;

}


delay(); //depounce


return 4;

}

//test row 2

R4=1;

R3=1;

R1=1;

R2=0;


delay(); //depounce


return 5;

}

if (C2 == 0) { //key 6 is pressed

delay(); //depounce


return 6;

}


delay(); //depounce


return 7;

}


delay(); //depounce


return 8;

}

//test row 3

www.unistring.com

R4=1;

R1=1;

R2=1;

R3=0;


delay(); //depounce


return 9;

}


delay(); //depounce


return 10;

}

if (C3 == 0) { //key A is pressed

delay(); //depounce


return 11;

}

if (C4 == 0) { //key B is pressed

delay(); //depounce


return 12;

}

//test row 4

R1=1;

R2=1;

R3=1;

R4=0;

if (C1 == 0) { //key C is pressed

delay(); //depounce


return 13;

}

if (C2 == 0){ //key D is pressed

delay(); //depounce


return 14;

}

www.unistring.com

if (C3 == 0){ //key E is pressed

delay(); //depounce


return 15;

}

if (C4 == 0) { //key C is pressed

delay(); //depounce


return 16;

}

return 0; // Means no key has been pressed

}

void main (void)

{

P1 =0xf0;

P3=0x00;

LCD_init();

LCD_row1();

LCD_puts("< SERIAL KEYPAD >");

LCD_row2();

LCD_puts(" INTERFACING ");

Delay(3);

LCD_clear();

LCD_row1();


LCD_row2();

LCD_puts("KEY : ");

while(1){

key=READ_SWITCHES();

if(key){

P3 = key-1;

LCD_clear();

LCD_row1();


LCD_row2();

LCD_puts("KEY : ");

switch(key)

www.unistring.com

{

case 1:

{

LCD_putc('0');

break;

}

case 2:

{

LCD_putc('1');

break;

}

case 3:

{

LCD_putc('2');

break;

}

case 4:

{

LCD_putc('3');

break;

}

case 5:

{

LCD_putc('4');

break;

}

case 6:

{

LCD_putc('5');

break;

}

case 7:

{

LCD_putc('6');

break;

}

case 8:

{

LCD_putc('7');

break;

}

case 9:

{

www.unistring.com

LCD_putc('8');

break;

}

case 10:

{

LCD_putc('9');

break;

}

case 11:

{

LCD_putc('A');

break;

}

case 12:

{

LCD_putc('B');

break;

}

case 13:

{

LCD_putc('C');

break;

}

case 14:

{

LCD_putc('D');

break;

}

case 15:

{

LCD_putc('E');

break;

}

case 16:

{

LCD_putc('F');

break;

}

}// switch

}//if

www.unistring.com

}//while

}//main

void Delay(unsigned int duration)

{

unsigned int r2;

for (r2 = 0; r2<= duration;r2++){

LCD_delay(250);

LCD_delay(250);

}

}

/*

* Filename : lcd.h

* Hardware : Controller -> P89V51RD2

* XTAL -> 11.0592 MHz

*

* I/O : RS -> P2.5

* Enable -> P2.4

* Data4567 -> P2.0,P2.1,P2.2,P2.3 */

#define LCD_DELAY 150 /* Delay for 1 ms */

#define LCD_clear() LCD_command(0x1) /* Clear display LCD */

#define LCD_origin() LCD_command(0x2) /* Set to origin LCD */

#define LCD_row1() LCD_command(0x80) /* Begin at Line 1 */

#define LCD_row2() LCD_command(0xC0) /* Begin at Line 2 */

/***************************************************

* Prototype(s) *

***************************************************/

sbit LCD_en=P2^4;

sbit LCD_rs=P2^5;

void LCD_delay(unsigned char ms);

void LCD_enable();

void LCD_command(unsigned char command);

void LCD_putc(unsigned char ascii);

void LCD_puts(unsigned char *lcd_string);

void LCD_init();

www.unistring.com

/***************************************************

* Sources *

***************************************************/

void LCD_delay(unsigned char ms)

{

unsigned char n;

unsigned int i;

for (n=0; n<ms; n++)

{

for (i=0; i<LCD_DELAY; i++); /* For 1 ms */

}

}

void LCD_enable()

{

LCD_en = 0; /* Clear bit P2.4 */

LCD_delay(1);

LCD_en = 1; /* Set bit P2.4 */

}

void LCD_command(unsigned char command)

{

LCD_rs = 0; /* Clear bit P2.5 */

P2 = (P2 & 0xF0)|((command>>4) & 0x0F);

LCD_enable();

P2 = (P2 & 0xF0)|(command & 0x0F);

LCD_enable();

LCD_delay(1);

}

void LCD_putc(unsigned char ascii)

{

LCD_rs = 1; /* Set bit P2.5 */

P2 = (P2 & 0xF0)|((ascii>>4) & 0x0F);

LCD_enable();

P2 = (P2 & 0xF0)|(ascii & 0x0F);

LCD_enable();

LCD_delay(1);

}

void LCD_puts(unsigned char *lcd_string)

{

while (*lcd_string)

{

LCD_putc(*lcd_string++);

}

}

www.unistring.com

void LCD_init()

{



LCD_command(0x28);

LCD_delay(2);

LCD_command(0x0C);

LCD_delay(2);

LCD_command(0x06);

LCD_delay(2);

LCD_command(0x01); /* Clear */

LCD_delay(256);

}

Results/Discussion:

After programming the code into the microcontroller just reset the microcontroller

and put it in the run mode. You can see what ever key is pressed the corresponding

value of that button will be displayed in the LCD Display and LED’s on the board.


To test the board

Connect the keypad to the header (CN6) and P1 using the 8 wire bus.

Note the P1 (Pin number 1 of the microcontroller) is connected to R1 of

the keypad connector.

For LCD is connected port P2

RS -> P2.5

Enable -> P2.4

Data4567 -> P2.0, P2.1,P2.2, P2.3

www.unistring.com

5. ADC, DAC interface to 8051.

Experiment – 5a

Write a program for interfacing a keypad to the microcontroller

Aim: Write a program for interfacing a keypad to the microcontroller.

Introduction: In this experiment a program is written in C language to read data from the keypad

and data is sent to the seven segment display to the computer through RS232 interface

available on the board.


• Write a program for interfacing adc and collecting the sampled value

and showing on the hyper terminal.


• The generated hex file will be downloaded in to the MC and verify the

result.

KIEL software is used for compilation of C files and the hex file can be generated.


Step1:


www.unistring.com

Step 2:

To create a new project just click the project menu and click new microvision project

, as shown in below figure.

www.unistring.com

Step 3:

Then a dialog box will be opened to give the destination as shown in the figure. You

can give the destination folder and save it.

www.unistring.com

Step 4:

To write a c file click the file menu and select the new document. The desired code is

written in the document. And this document is needed to be added to the project.

Step 5:

In the project window on the left hand side you can see a project window .in the

window a folder called target can be seen to that folder another folder can be seen as

target source group1. the c file which is written nedded to be added to that folder . to

add a c file to that folder right click the source group1 folder and a menu will be


www.unistring.com

From that menu you can see add files to source group option. If you click that

option the c file will be added to the project.

Step 6:

Before bulding the project some settings are to made, from the main menu click the

flash, you can see the option as configure flash tools . you click that option you can

find a menu as shown in the figure.

www.unistring.com

From that menu click output and select an option called create hex file. And in the

target menu give the oscillator frequency as 11.0592.

Step 7:

Now all the hard work we have done to build the project and to create the hex file

From the main menu select the project and in that an option called build target can be

seen , just click that . if all the coding is correct and the syntaxes are correct an hex

file will be generated.


� Open the Flash Magic tool for downloading into the Microcontroller Board.

Click on Device menu select option you will be popped up with a window

named choose device. Under choose device options select 8051 and click on

Ok button to open flash magic tool to download the hex file in to the MC and

is as shown below.


www.unistring.com

� Change setting for Flash Magic as shown in the above figure

COM Port Choose the Appropriate COM Port of the computer. Generally it

is COM1

Baud Rate 9600

Device 89V51RD2

Interface None(ISP)

Oscillator Freq (MHZ) 11.0592



Now Goto


and uncheck the “Use DTR To Control Reset” as shown in the figure below

www.unistring.com


� Select the switches.Hex file from the Folder in which switches.c file is

located.

� Turn On the Board Power. The RUN/PROG button can be any where (as

89V51RD2)


� Press and hold the reset button on board and press start button on flash magic.

wait until a small window comes with message "Reset The Device Into ISP

Mode "comes.


� You can see the messages in flash magic tool as Erasing the Device,

Programming the Device ,Verifying and Finished � (10)Once you get finished message in the flash magic. press reset once to enter

in run mode.

Results/Output verification: Now serial communication program is running on

Microcontroller. Open flash magic tool and under tools menu click on terminal as

shown below.

www.unistring.com

A window will be popped up and select the following settings as done in the previous

program .

C SOURCE CODE

#include <reg51.h> /* define 89C52 registers */

#include"lcd.h"

sbit rd=P1^0; //Read signal P1.0

sbit wr=P1^1; //Write signal P1.1

sbit intr=P1^2; //INTR signal P1.3

void conv(); //Start of conversion function

void read(); //Read ADC function

void display();

void Delay(int a);

unsigned char adc_val;

unsigned int value,temp,temp1,temp2,temp3;

void Delay(int a){

char i;

for(i=0;i<a;i++)

{

LCD_delay(250);

LCD_delay(250);

www.unistring.com

}

}

void main(){

P0=0xFF;

P3=0X00;

P1=0x04;

LCD_init();

while(1){

LCD_clear();

LCD_row1();

LCD_puts("ADC804 INTERFACE");

conv(); //Start conversion

read(); //Read ADC

P3 = adc_val; //Send the read value to P3

display();

Delay(4);

}

}

void conv(){

wr = 0; //Make WR low

wr = 1; //Make WR high

while(intr); //Wait for INTR to go low

}

void read(){

rd = 0; //Make RD low

adc_val = P0; //Read ADC port

rd = 1; //Make RD high

}

void display(){ // display the adc vvalue in the form of

milli volts

LCD_row2();

LCD_puts("VOLTAGE:");

value=adc_val*19;

if(value>=1000){

temp=value/1000;

www.unistring.com

adc_val=temp+48;

LCD_putc(adc_val);

}

temp1=value%1000;

if(temp1>=100&&temp1<=999){

temp=temp1;

temp=temp/100;

adc_val=temp+48;

LCD_putc(adc_val);

}

else

LCD_putc('0');

temp2=temp1%100;

if(temp2>=10&&temp<=99){

temp=temp2;

temp=temp/10;

adc_val=temp+48;

LCD_putc(adc_val);

}

else

LCD_putc('0');

temp3=temp2%10;

if(temp3>0&&temp3<10){

temp=temp3;

adc_val=temp+48;

LCD_putc(adc_val);

}

else

LCD_putc('0');

LCD_putc(' ');

LCD_putc('m');

LCD_putc('v');

}


To test the board

Power supply cable should be connected to the M7.1 Board and serial cable must be

connected to the computer.

www.unistring.com

The Data line of the ADC is connected to the P0 of microcontroller.

P0 pin number 0 should be connected D0 of the ADC.

The RD, WR, INTR signals are connected to the P1.0, P1.1, P1.2 respectively.

The VREF signal is connected to the +5V supply of the board.

The P3 is connected to LED PORT (CN4).

The ADC voltage is displayed in LCD, the digital value is shown in LED PORT.


RS -> P2.5

Enable -> P2.4

Data4567 -> P2.0, P2.1,P2.2, P2.3

www.unistring.com

Experiment – 5b

Write a program for generating a sine wave using DAC

Aim: Write a program for generating a sine wave using DAC and SIN look up tables.

Introduction:

In this experiment a program is written in C language to generate a sin

wave using dac and sine look up table.


i) Write a program for generating a sine wave using DAC and SIN look up tables.





generated.

www.unistring.com


Step1:

Open the kiel ide and you can see a menu as shown in the figure.

Step 2:



www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:







www.unistring.com



Step 6:




www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com



file is located.


where (as 89V51RD2)










C SOURCE CODE

// this program worked based on R-@R laders DAC module

www.unistring.com


void main () { /* main program */

unsigned char data1;

unsigned char x;

unsigned char sine[64]={127, 139, 152, 164, 176, 187, 198, 208, 217, 225,

233, 239, 244, 249, 252, 253,

254, 253, 252, 249, 244, 239, 233,

225, 217, 208, 198, 187, 176, 164, 152, 139,

127, 115, 102, 90, 78, 67, 56, 46, 37,

29, 21, 15, 10, 5, 2, 1,

0, 1, 2, 5, 10, 15, 21, 29, 37, 46, 56,

67, 78, 90, 102, 115}; // sinewave look up chart

data1 =0x00;

while(1)

{

for(x=0;x<64;x++)

{

P0 = sine[x];

}

}

}

www.unistring.com

Results/Discussion:

After programming the code into the microcontroller just reset the

microcontroller and put it in the run mode. You can observe the sin

wave in the CRO.


To test the board

Connect the DAC module to the P0 connector as shown below.

The out put sine wave form You can observe the red wire is connected

CRO positive and ground pin is connected ground on the Board

www.unistring.com

Experiment –6a

Write a program for interfacing the 16x2 LCD MODULE

Aim: Write a program for interfacing the 16x2 LCD module in 4- Bit mode.

Introduction:

In this experiment a program is written in C language to display a

message in the lcd first and second line and then clearing the first and

second line. This program is kept in an continuous loop and the output

can be seen on the board.


• Write a program for lcd interface





generated.


Step1:


www.unistring.com

Step 2:



www.unistring.com

Step 3:



www.unistring.com

Step 4:




Step 5:







www.unistring.com



Step 6:




www.unistring.com



Step 7:


create the hex file










is as shown below.

www.unistring.com




Baud Rate � 9600

Device � 89V51RD2





Now Goto



figure below

www.unistring.com



file is located.


where (as 89V51RD2)










Results/Output verification: Now the lcd program is running on

Microcontroller. And the output can be seen in the board. C SOURCE CODE

# include <reg51.h>

www.unistring.com

# include"lcd.h" // refer LCD.H code for more to about LCD

/* Hardware : Controller -> P89V51RD2

* XTAL -> 11.0592 MHz

*

* I/O : RS -> P2.5

* Enable -> P2.4

* Data4567 -> P2.0,P2.1,P2.2,P2.3

* Compiler : uvision 4

* Author : [email protected]

* Date : 18/05/10

*/

void Delay_sec(unsigned char s);

main( )

{

LCD_init();

while(1){

LCD_clear();

Delay_sec(1);

LCD_row1();

LCD_puts(" HELLO LCD123. ");

LCD_row2();

LCD_puts(" TEST PROGRAME ");

Delay_sec(5);

LCD_clear();

Delay_sec(1);

LCD_row1();

LCD_puts(" Hello Welcome ");

LCD_row2();

LCD_puts("UNISTRING TECH P L");

Delay_sec(5);

}

}

void Delay_sec(unsigned char s)

{

unsigned char n;

for (n=0; n<s; n++){

LCD_delay(250);

LCD_delay(250);

}

www.unistring.com

}

// Filename : lcd.h

# define LCD_DELAY 200 /* Delay for 1 ms */

# define LCD_clear() LCD_command(0x1) /* Clear display LCD */

# define LCD_origin() LCD_command(0x2) /* Set to origin LCD */

# define LCD_row1() LCD_command(0x80) /* Begin at Line 1 */

# define LCD_row2() LCD_command(0xC0) /* Begin at Line 2 */

# define lcd_port P2

//LCD Registers addresses

# define LCD_EN 0x10

# define LCD_RS 0x20

/***************************************************

* Prototype(s) *

***************************************************/

sbit LCD_en=P2^4;

sbit LCD_rs=P2^5;

void LCD_delay(unsigned char ms);

void LCD_enable();

void LCD_command(unsigned char command);

void LCD_putc(unsigned char ascii);

void LCD_puts(unsigned char *lcd_string);

void LCD_init();

void lcd_reset();

/***************************************************

* Sources *

***************************************************/

void LCD_delay(unsigned char ms)

{

unsigned char n;

unsigned int i;

for (n=0; n<ms; n++)

{

for (i=0; i<LCD_DELAY; i++); /* For 1 ms */

}

www.unistring.com

}

void LCD_enable()

{

LCD_en = 1; /* Clear bit P2.4 */

LCD_delay(1);


}

void LCD_command(unsigned char command)

{


P2 = (P2 & 0xF0)|((command>>4) & 0x0F);

LCD_enable();

LCD_delay(1);

P2 = (P2 & 0xF0)|(command & 0x0F);

LCD_enable();

LCD_delay(1);

}

void LCD_putc(unsigned char ascii)

{

LCD_rs = 1; /* Set bit P2.5 */

P2 = (P2 & 0xF0)|((ascii>>4) & 0x0F);

LCD_enable();

LCD_delay(1);

P2 = (P2 & 0xF0)|(ascii & 0x0F);

LCD_enable();

LCD_delay(1);

}

void LCD_puts(unsigned char *lcd_string)

{

while (*lcd_string)

{

LCD_putc(*lcd_string++);

}

}

void lcd_reset()

{

lcd_port = 0xFF;

LCD_delay(20);

lcd_port = 0x03+LCD_EN;

lcd_port = 0x03;

LCD_delay(10);


www.unistring.com

lcd_port = 0x03;

LCD_delay(1);


lcd_port = 0x03;

LCD_delay(1);


lcd_port = 0x02;

LCD_delay(1);

}

void LCD_init()

{ LCD_delay(10);

lcd_reset();



LCD_command(0x28);

LCD_delay(1);

LCD_clear();

LCD_delay(1);

LCD_command(0x06);

LCD_delay(1);

LCD_command(0x0C);

LCD_delay(1);

LCD_clear(); /* Clear */

LCD_delay(100);

}

Results/Discussion:

After programming the code into the microcontroller just reset the

microcontroller. You can see some text displayed in the LCD display.



RS -> P2.5

Enable -> P2.4

Data4567 -> P2.0, P2.1,P2.2, P2.3

www.unistring.com

Note:

For more information about refer 8051 book in the CD

manual for cycle 1

Documents

source code include include

target source group1

left hand side

baud rate gen

default baud rate

configure flash tools

unsigned char ms

flash magic opens