manford machinery co., ltd - milling machine,bed … operationmanu… · manford machinery co., ltd...

MANFORD MACHINERY CO., LTD

1

CONTENTS Chapter 1. Safety Regulations

1.1 General Safety Rules -------------------------------------------------------- 1.2 Dangerous Areas of Machines ---------------------------------------------- 1.3 Warning labels , contents and locations ----------------------------------- 1.4 Intended use of the machine ------------------------------------------------ 1.5 Machine life ------------------------------------------------------------------

Chapter 2. Description of The Machine

2.1 Specifications of Machines and Accessories -------------------------- 2.2 Out-looking , Dimensions and Name of Majors Units --------------- 2.3 Operation Position -------------------------------------------------------- 2.4 Noise Level --------------------------------------------------------------- 2.5 Operation Environment ------------------------------------------------- 2.6 Power Supply ------------------------------------------------------------

Chapter 3. Transportation and Installation

3.1 Wooden Case Packing ---------------------------------------------------- 3.1.1. Wooden-case Transportation ----------------------------------------- 3.1.2. Machine Transportation -----------------------------------------------

3.2 Installation -------------------------------------------------------------------- 3.2.1.Installation Conditions ------------------------------------------------- 3.2.2. Installation Establishment -------------------------------------------- 3.2.3. Machine Horizontal Adjustment -------------------------------------- 3.2.4. Power Connection -----------------------------------------------------

3.3 Preparation for Trial Run After Installation ---------------------------- 3.1.1 Check points before turning ON the machine ------------------- 3.1.2 Verticality alignment between the spindle and table r -------------

Chapter 4. Operation Description

4.1 Preface ------------------------------------------------------------------- 4.2 Operation Panel -------------------------------------------------------- 4.3 Safe Operation lathe chuck ------------------------------------------- 4.4 Work Piece clamping methods ----------------------------------------- 4.5 Bar feeder --------------------------------------------------------------- 4.6 Replacement of Turret tool to the turret ------------------------------ 4.7 E-stop ---------------------------------------------------------------------

Page 1-3 Page 4 Page 5-6 Page 7-9 Page 10 Page12-15 Page16-17 Page18 Page19 Page20-22 Page23 Page24 Page25 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page29-33 Page26-29 Page26-29 Page26-29 Page26-29 Page26-29 Page34-35 Page26-29


2

CONTENTS Chapter 5. Maintenance and Trouble shooting

5.1. Maintenance ---------------------------------------------------------------- 5.1.1. Safety precautions for maintenance ---------------------------- 5.1.2. Daily inspection ---------------------------------------------------- 5.1.3. Periodical Inspection ---------------------------------------------- 5.1.4. Lubrication ---------------------------------------------------------

5.2. Maintenance of each units ----------------------------------------------- 5.3 Trouble Shooting -----------------------------------------------------------

Chapter 6. Safety Circuit -----------------------------------------------

Chapter 7. Parts Lists ---------------------------------------------------

Page 1-3 Page 4 Page 5-6 Page 7-9 Page 10 Page 11 Page26-29 Page12-15 Page16-17 Page18 Page19 Page20-22 Page23 Page24 Page26-29 Page26-29


3

Chapter 1. Safety Regulations

1.1 General Safety Rules

1. The machine may become a source of danger when:

used improperly.

not observing the instructions for use and warning given in this manual

Used by unskilled personnel or non-specialized maintenance personnel

2. This machine shall be only sued for metals removal. Work piece like wood, flammable or poisonous materials can not be allowed to operate by this machine.

3. This machine shall be operated and maintained by qualified personnel, who have received the professional training and have through understanding of the machine characteristics and shall related safety rules.

4. Employer shall have operators to attend safety training as machine.

5. Employer shall instruct operators with their best knowledge about the dangerous operation.

6. Operator shall always refer to this manual and follow the instructions posted on the machine before operating or maintaining the machine.

7. Check the location of stop and emergency switch first before operating the machine.

8. Do not bypass the safety equipment.(e.g interlock circuit etc….)

9. Shot down the power, remove work piece from machine table, clean and lubricate the machine, and move every moving stand to the center of travel as routine procedures when finishing work.

10. Make sure that the power is shut off before examining the electrical circuit and use right apparatus.

11. Modifications are prohibited

Any modifications or alterations carried out on the machine by an operator and/or maintenance personnel are forbitden for safety reasons.

The MANFORD MACHINERY CO., LTD

declines any liability in case of non-autohorized modifications.


4

1.2 Dangerous Areas of Machines

1. Do not touch any electrical equipment such as high voltage wiring, motor connections, or transformers, etc… unless you are qualified to do so. Incorrect use could result in a serious electrical shock.

2. Touching switches with wet hands could result in an electrical shock.

3. Do touching working table and spindle with operation machine.

4. Do not move, replace or clean the work piece while the spindle is operating or machine is auto-feeding.

5. Do not use any tool on the machine during operating.

6. Area marked with < > and < > indicate high speed sliding or rotating machine parts. Be alert when working near these areas.

fig-1.2-1


5

1.3 Warning

1. If the machine is used by several people, to reset the coordinates when you take over, unless common coordinates are used by all operators.

2. The floor could become slippery because of spilt water or oil and cause an accident. Ensure the floor is clean, dry and orderly at all time.

3. Do not touch any switch without care.

4. Provide ample working space to avoid danger in an emergency.

5. Be sure you know the function of a switch and how to use it before touching it.

6. Be sure you know how to stop the machine in an emergency.

7. Be sure the machine has stopped and the power is off before replacing a fuse.

8. The workable adjacent to the machine should be secured to prevent the work piece from falling onto the machine.

9. The warning signs on the machine following :


6


7

1.4 Intended use of the machine

1. This machine shall be only sued for metal processing.

2. Operation this machine must be read the instruction manual.

3. Operation this machine before to training

1.5 Machine life

1. The machine normal operation and periodical maintenance with the machine life for 10 years.

2. This machine life is finished can be to liaise my company or local machinery manufacture, to cope with to declare something no longer serviceable or usable.


8

Chapter 2. Description of The Machine

2.1 Specifications of Machines and Accessories

1. machine specification

SPECIFICATION CB-170 CB-180 CB-185 CB-410

Table size 1270mm 250mm

(50〞 10〞)

1370mm 250mm

(54〞 10〞)

1270mm 305mm

(50〞 12〞)

1270mm 380mm

(50〞 15〞)

Longitudinal

travel 720mm(28.3〞) 820mm(32〞) 850mm(33.4〞) 1000mm(37.4〞)

Cross travel 406mm(16〞) 500mm(20〞) 450mm(17.7〞) 500mm(20〞)

Vertical travel 490mm(19〞) 450mm(17.7〞) 450mm(17.7〞) 460mm(18〞)

Spindle nose to

table top (D)

75~565mm

(3〞~22.2〞)

90~540mm

(3.5〞~21.2〞)

45~495mm

(1.8〞~19.5〞)

140~600mm

(5.5〞~23.6〞)

SPINDLE

Spindle taper NST#30 (or R8) NST#40 NST#40 NST#40

Spindle Speed 60Hz: 60~4500

50Hz: 50~3800

60Hz: 60~4300

50Hz: 50~3600

75~5000

inverter system

50~3600

inverter system

Stroke of quill 127mm(5〞) 140mm(5.51〞)

Mm 04 – 08 - 14 035 – 07 - 014 Quill feed

rate inch 0015 – 003 - 006 0013–0027-0055

Swiveling angle

of head(R&L) 45°

Spindle center to

column front

surface (E)

465mm(18.3〞) 500mm(20〞) 490mm(19.3〞)

FEED RATES

XYZ axes feed

rates 1~3000mm (0.1~110ipm)

Rapid traverse

X,Y,Z axes 5000mm (200ipm)

MOTOR

Spindle drive

motor 3HP 5HP 5HP inverter motor

5HP(7~1/2HP

inverter)

Drive on X,Y,Z 1HP (Depends on CNC system)

Coolant pump 1/8HP 1/4HP

L W H(mm) 1640 1840 2335 (64.5〞 68.5〞 92〞)

1750 2230 2400 (69〞 87.5〞 94.5〞)

1790 2230 2440(70.5〞 88〞 96〞)

Weight 2000kgs 2060kgs 2300kgs 3100kgs


9

2. Maximum allowable cutting capacity / Recommended maximum allowable loading

2.1 Maximum allowable weights on the table

Type CB-170 CB-180 CB-185 CB-410 Loading weights 200 kgs 200 kgs 250 kgs 300 kgs

2.2 Maximum allowable cutting capacity

Type CB-170 CB-180 CB-185 CB-410 Face Milling 3〞 4〞 4〞 4〞

Drilling 5/8〞 3/4〞 3/4〞 3/4〞

Ps: cutting material: S45C 3. Head models

MF-B170 MF-B170VS

MF-B180 MF-B180VS


10

2.2 Out-looking and Name of Majors Units

NO appellation NO appellation 1 speed head 5 Base 2 Power box 6 Spindle motor 3 Work table 7 Control panel 4 Handle wheel 8 Timing belt box

1

3

2

4

5

7

8

6


11

2.3 Operation Position

operation position marked with


12

2.4 Noise Level

Noise level of this machine is below 85dB(A) when measured under the conditions of the most international standards. However, subject to various factors beyond the manufactures control, the noise level could be higter than 85Db(A). Actual working conditions, (work piece material, tool performance, cutting coolant, or the like), may fifer from conditions laid down in specific international standards.

Appropriate hearing protection equipment should be worn whenever the noise level causes discomfort, to minimize the risk of hearing injuries.

2.5 Operation Environment


13

2.6 Power Supply

1. Connecting –disconnecting the machine from the main

1.1 Power supply characteristics

The power supply must have following characteristics:

Power supply system:

Rated voltage: 220V ~ 380V ± 5%

Number of phases: 3

Frequency: 50 ~ 60 ± 5% Hz

1.2 Power supply cable

(1) The machine’s power supply cable must show at least one quality control mark, as for instance CNS.

(2) Each wire of the power supply cable must have a cross section of at least 1.5m2

(3) The cable must be protected against overloads, short circuits and mechanical or chemical agents that may damage it.

(4) The machine must be protected against short circuit currents exceeding the cutoff power as shown in the above table.


14

Chapter 3. Transportation and Installation

3.1 Wooden Case Packing

3.1.1. Wooden-case Transportation

Figure 3.1.1-1 machine packing with wooden

Figure 3.1.1-2 wooden with forklifting


15

3.1.2. Machine Transportation

1. Cautions for unpacking

(1) To transport the machine, it is necessary to support the machine with the crated case or pallet to avoid moisture. In case of damage by moistening, please contact our agents or transport’s agents.

(2) After unpacking, check and see if all the accessories and tools are intact, otherwire, please contact our agent.

(3) Prior to unpacking, transport may be made by using forklift, and a reinforced cable.

(4) After unpacking, do not move the sliding faces as long as the rustproof oil on them are not cleaned off and followed with the lubrication.

(5) To hoist the unpacked case by reinforced cable, the motion shall observed strictly the instruction appeared on the side of the wooden case.

2. Hoist handing

(1) The safety weight of the hoist must heavier than the machine’s weight.

(2) Insert steel bar through the machine and joint the reinforced cable with base hoisting hook to hang it up.(figure 3.1.2-1)

(3) Use a soft rag or paper plate to protect the machine from being harmed by the cable.

(4) Always remains balance during the hoisting.

(5) Use the lowest speed of the hoist to rise up the machine.

(6) Do not hoist the machine too high. The best height is to keep the machine base approximately 10cm from the ground.

(7) Operators must remains a safety distance from the machine during hoisting and people are not allowed to enter a region at least 2m from that area.


16

3. Forklift Handling

Forklift is used if the hoist is absent(figure 3.1.2-2)

(1) No need to remove the bottom wooden case when forklift is used. Please carefully and avoid collision so that precision is not affected.

(2) Keep an eye to the center of gravity to maintain the machine in equilibrium.

(3) The weight of the forklift must heavier than the machine’s total weight.

(4) A quantified driver is needed to drive the forklift.

Figure 3.1.2-1


17

Figure 3.1.2-2


18

3.2 Installation

3.2.1 Installation Conditions

(1) It is very important for the machine to calibrate calibrate horizontal position. Please pay more attention to calibrate it. Please clean the table before calibrating. Put the level on the middle of the table, be sure it is completely horizontal in both longitudinal and transversal direction.

(2) The foundation must be concrete ground and the thickness will have influence on the accuracy of the machine.

(3) If the machine isn’t laid down on concrete ground, correcting horizontal position by using leveling bolt blocks. Clean the bottom of the blocks and put it down on the position which the machine will be laid down. Every leveling bolt should focus on the concave of each block, and lay down the machine smoothly. Caibrate the horizontal position by adjusting the leveling bolts(1) as figure 3.2-1 show.

(4) check monthly after 6~8 months.

Figure 3.2-1


19

3.2.2 Installation Establishment

(1) Use kerosene to clean the metallic surface which are covered of rustproof grease before packing. After that, use a clean rag to clean the surface and finally lubricate them with clean lubricant.

3.2.3 Machine’s horizontal adjustment

a. After cleaning the machine table, please two precision level horizontally and vertically respectively (figure 3.2-2). If there is only one level, operator can examine the machine repeatedly in the two directions.

b. Refer to figure 3.2-3 , before the alignment, combine the horizontal bolt and the nut so that the nut is close to the head of head bolt. Placing six horizontal block to the horizontal bolt hole of the base, screw six horizontal bolts to the bolt hole until reach the center of the approximately 5mm by turning the horizontal bolt clockwise. After that, starts the alignment.

c. During the adjustment,

d. A newly installed machine should be aligned weekly. After the foundation is stable, number of alignment can be reduced to twice a year.

Figure 3.2-2


20

3.2.4. Power Connection

1. Procedure for connection to mains

1.1 The machine can be considered as properly connected to the mains when all indications given in the following paragraphs have been observed.

1.2 Once the machine has been connected, the end-user must check that the direction of motor’ rotations respects the directions shown by the respective arrows, if the rotation is not bidirectional.

1.3 Trained and qualified personnel must connect the machine to the mains with special cable.

2. Connecting procedure:

1) Connect the cable to the distribution board, observe the correct phase sequence (shown in figure 3.2-3), connect the yellow/green wire to the grounding system according to the safety regulations.

2) Make sure the grey/block disconnecting switch (if installed) is set to position, in order to supply the machine with power.

3) Start up the spindle through its control. 4) Make sure it rotates in the correct direction, If it rotates clockwise, then the

machine is properly connected, If not, turn the machine off again, go back to step 1 and invent two phases.

Figure 3.2-3


21

3.3 Preparation for Trial Run After Installation

3.3.1. Check points before turning ON the machine

1.1. Power connection

a. Check and see if the motor voltage and power source voltage are conformed. If not, call the technician to repair it.

b. Make sure that the wires are tightly screwed on the switch.

c. Make sure that the wire is grounded.

d. always switch off the power before connection or changing wires.

1.2. Testing of direction of rotation

a. Open the power and turn the switch of the motor to “on” position, examine the direction of rotation of the spindle. The spindle must rotate in the clockwise direction if it is seen in front of the machine. Change the phase of the current by altering the two wires if the direction is not the one we discussed above.

b. The same method can be applied to cooling device and step-up motor.

c. Do not install the tools during the testing.

d. Make sure everything is normal before switch on the power.

3.3.2. Verticality alignment between the spindle and table

a. loosen the four machine head bolts (refer to figure3.3-1) and the four machine head nuts. However, the bolts and nuts can not be loosened totally to prevent the components from a sudden tilting.

b. please refer to our company’s precision inspection table for precision requirements.

c. loosen and align the bolt to the required precision and them screw up the

four machine head bolts .

d. use a meter to check the verticality between the spindle and the table whether it fits the precision requirement. After that screw up all the four machine head bolts.


22

Chapter 4. Operation Description

4.1 Preface

4.1.1 revrsing switch

The rotaion of the motor is controlled by the reversing switch (figure 3.2-2). When the high low speed lever is placed at the high gear position (forward),and the switch is on the ”for”，then the motor turns clockeise ,when thw switch is on

“rev”,the motor tuens counterclockwise. When the switch is on “off”,then the power source is cut off. When high low speed lever is is placed at the “low” position (backward),the directions are reversed.

4.1.2 spindle bracke

power must be shut off before braking. When the spindle speed is lower than 200r.p.m,operator can pull down or up the brake lever (figure 3.2-2) to stop the spindle.

4.1.3 chucking of tooing shank and dismantling

a. Firstly ,the screw of the draw bar is right turn when the spindle is at the highest porint. When the screw is turned clockwise, it is for locking of tooling shank, and vice versa .to take out the tooling shank, the diaw bar must be turned from therr to five rounds. Then,use a soft mallet to hit slightly on the draw bar to allow the tooling shank to separate from the spindle. Tutn the draw bar until the tooling shank comes off totally.

b.when there is a slot in the shank and the spindle taper is R8,it is necessary to turn the tooling shank in the process of chucking, so that the tooling shank key way will slide into the key qrooves.

figure 6-3 figure 6-3


23

4.1.4 spindle feed (figure 3.2-2)

1. manual feed

The manual feed lever (1) is installed on the right side of headstock.the spindle will travel vertically ehen the lever is tuyned, there are 12 positions to be chosen ,an operator can freely take out the lever and install it again at the position deemed ptoper and fit. In manual feed,the feed control handle (4) must be placed at the position “A” as shown in (figure 6-3).

2.manual micro-feeding

To effectuate the manual micro-motion feed ,the power feeding transmission engagement crank(2) shall be placed at “OUT” position,and feed reverse knob(3) ,at neutral position. Feed control lever(4) must be pulled form “A” TO”B”. this is to engage the overload clutch ,turn the feed hand wheel (5)clockwise for qull downward feed ,and vice-versa.

3.Automatic feed

a. Loosen the quill lock(6)

b. turn the power feed transmission engagement crank(2) from “OUT”to “IN” Position. Make certain to engage the worm gear cradle with the spindle gear cradle with the spindle gear hub so that the driving will be directed form the spindle worm and worm gear before it is passed to the speed change gears.

c. feed speed is in three stages, H, L, and m. selection may be made by quill feed selector (7).

d. pull the feed control lever(4) form “A” TO “B” position to engage the overloaf clutch for automatic feed mechamism,

e. when the feed reverse knob(8) presses inwatd, it is for downward feed, and vice-versa, the middle position is neutral.

f. the working depth may be set by mictometer adjustment muts(9) (each graduation is 0.02mm or 0.001”) .when the quill stop block(10) contaction the micrometer adjustment nut (9), the feed control lever (4) may simply jump form ”B” to “A” position owing to the connecting motion between the feed trip lever and feed trip plunger.this will disengare the overload clutch and stop the spindle feed.

g. Do not move the power feed transmission engagement crank(2) when the spindle is in revolution.


24

4.1.5 speed change of spindle (figure 3.2-2)

The speed change may be effectuated by the chosen high and low speed lever (1).when (1) is engaged in the righ as 500 to 30000RPM. When 1 is positioned at the right rear, the spindle may have a speed of 60-580RPM. Themeutral lever position is in the right down.

a. The spindle must be motionless completely dyring the speed change.

b. To shift the high speed into the low one, the spindle must be slightly turned to make it easier for the back row gear to engage.

c. To shift the low speed into the high one, use the brake lever so as to put a stop to the spindle clutch, then turn the spindle slightly so that the clutch may be engaged feadibli ,a “click” siynf of engagement may be sensed at thin moment.

d. The direction of low speed rotation is opposite to that of the high speed, by the reversing switch,the direction may changed to that of he high speed revolution.

4.1.6 speed change hand wheel

a. when the turning hand wheel is turned clockwise, it is for higher speed, ang vice versa.

b. Do ndt change the speed when rhe spindle stands still.

c. Avoid to use it when the speed is in excess of 3000RPM.

d. In the process of speed change form high speed ro safeguard to low speed, and vice versa, do not change the speed raidly to safeguaed the service life of the internal mexhanism.

e. It takes roughly 10 to 15 minutes to change form low speed to high one, and vice-versa.


25

4.2 Machine body operations

4.2.1 zero positioning

1. Loosen the nut (1) of dial ring.

2. Turn the dial right (2) to zero position.

3. Lock the nut (1) of dial ring.

4.2.2 setting of sliding surface of work table, saddle and knee(figure 3.2-2)

Lock levers(3) are clockwise for seting amd counterclockwise for releasr, All non-feed slipping and increase machine’s stadility.


26

Chapter 5. Maintenance and Trouble shooting

5.1 Dismantling of motor

1. start the motor and turn the speed switch (1) to the center position of 60-4200ROM.

2. cut off the motor power source amd take off wire press board and reversing switch.

3. take out the therr concave hexagonal bolts (3) under the motor pulley cover.

a. Use two screw drivers to insert into the two holes between the motor pulley cover and the belt housing. Then pus down to loose the motor pulley cover(2).

b. Place a screw driver in the speed change spring piecer (4) to loose the motor pulley cover when the above mentioned mentioned method failed.

4. Lock two hexagonal bolts(M64╳45) into the motor vari-disc(5) to compress the speed change spring so as to separate the retainer ring(7).

5. take off the two hexagonal bolts (8) that locked the motor. The motor may be lifted up. Motor vari-dise amd speed change belt are still kept insibe the belt housing.

6. Change the speed to 4200RPM and pull back the belt, install the motor’s wheel amd the retainer ring to the shagt. Take out the two screw drivers fotm the belt housing. Finally installing just reverse the order of dismantling.


27

5.2 Replacment of speed change belt

1. Refer to 5-1 for dismantlinf of motor.

2. take off draw bar(1).D

3. Dismantle the four hexanonal concave bolts (2) and use two then to lift the

bearing housing(3).

4. Remove from atop the two hexagonal concave bolts(4) and take off the

bolt sleever (5).

5.Dismantle six hrxagonal concave blts 6 under the gear housing to dismantle the upper belt housing (7).

6.when the speed change belt(8) is replaced accordingly restore the machine by reversing the orders.


28

5.2 Replacment of brake block

1. Refer to 5-1 for motor dismantling.

2. Refer to 5-2 on replacement of speed change change belt to dismantle the upper belt housing.

3. take off the hexagonal concave bolt(1) of the two seting bearing houcing and remove the front vari-disc assembly set(2).take off the spring(3) and the brake block(4) can be replaced then.

4. Reverse the order to restore the machine assembly after the brake block is replaced.


29

5.4 Replacment of the timing belt

1. Refer to 5-1 for motor dismantling amd refer to 5-2 on replacement of speed change belt to dismantle the motor (1) and the upper belt

housing(2)

2.take off the hexagonal concave bolt(3),move the brake bade(4), and then the timing belt(5) can be replaced.

3. Restore the machine structure by reversing the steps once the belt is replaced.


30

5.5 Replacment of V-shaped belt

1. Loosen the handle (1).

2. Pull forward the handle (2) to let the motor moving to the front and loosen the belt.

3. Adjust the belt to the required speed on the belt pulley.

4. When the belt is in position ,push backward the hadle (2) so that the belt and the pulley (3) are in tightly contact situation.

5. Screw the handle (1)

1

2

3


31

5.6 Adjustment of backlash of lead screw

After a certain period time,a clearance is developed between the lead screw and its nut due tp friction. Therefore between itself and the lead screw.

5.6.1 Adjustment of cross lead screw

1. Turn counterclockwise the crank(1) and move the saddle seat to the foremost position of knee.

2. Remove the two setting pins (3) of the front bearing bracket (2) and take off the four socket hd cap screw (4).

3. Support the cross feed bearing bracket(2) and turn clockwise the crank(1) so that bracket will be separated from the knee with a certain distance between them(fig 5-7, the distance must be longer than the length of the adjusting tool)

4. Insert the larger end of clearance adjusting tool into the knee and turn the locking nut(5) one round counterclockwise. Reverse the adjusting tool and insert the smaller end into he knee. Turn the nut (6) clockwise and lock it up.

5. Turn clockwise and counterclockwisr the crank and meanure a clearanve of approximately 3-4 qraduations (0.06mm-0.08mm or 0.003”-0.004”) on the dial.lock up(5) consequently.

6. Turning counterclockwise the lead screw into the knee until the front bearing bracket seat gets in contact with the knee. Insert the two setting pins(3) and lock up tightly the four cap screw(4) of the bearing bracket.


32

5.6. Adjustment of backlash of longitudinal lead screw

1. Move the work table to the center of saddle.

2. Insert the large end of backlash adjustment tool into the left side of saddle. Turn the locjing nut(1) counterclockwise one round. Reverse the end of adjustment tool and insert the small end into same position and turn the lead screw adjusting nut (2) clockwise.

3. Turn the crank (3) slightly clockwise and counterclockwise and dial

(0.6-0.8mm or 0.003”-0.004”),before the nutis locked tightly again.

5.7 Adjustment of play between Gibs

As a result of long-term operation between the sliding surface amd gibs, the worn-out gibs will create a clearance therefore the gibs must be adjysird to keep the precision of sliding surfaces.

5.7.1 Adjustment of work table gibs

1. Loosen the lock lever(1).

2. Clean the slide way and the lubricant

3. Use a screwdriver and adjust the gib screw (2) on both sides of saddle seat.

4. Adjuating skill: if the turning of crank (Figure 7-8, (3)) is sensed too loose , loosen slightly the adjusting gib screw on the right side of saddle. Then, lock up the adjusting gib screw on the left side. Turn the crank again to see if it is in good tightness. Otherwise, loosen the left adjusting gib screw and lock the right one tifhtly. Rapeat the same motion until the work table sliding is satisfactory. Replace the excessive worn-out gib whenever necessary.

5. Replace the gibs if they are over worn-out.


33

5.7.2 Adjustment of saddle cib (Figure 7-10)

saddle gib is attached to the position between the left side of saddle and knee doverail. The adjustment can be performed as follows:

1. Loosen the saddle lock bolt(1).

2. Move the saddle to the foront part of knee.

3. Take off the wiper holdr (2) of saddle.

4. Clean the slide way and add the lubricant.

5. Use a screw driver to adjust the gib screw(3) of the daddle.

6. Employ the dame methods (5.7.1) to adjust the work table gib.

7. Lock up the wiper holder (2) on the saddle.


34

5.7.3 Adjustment of Head elevating gib (Figure 7-11) 1. Take off the head support’s wiper holder (3). 2. Clean the slide way and add the lubricant. 3. Raise the support to the highest position. 4. Use a screw driver to adjust the gib screw (1) of the knee. 5. Employ the same methods as adysting the work table gib. 6. Restorw and lock up the wiper holder(3).

5.8 Maintenance Under long-term operations, if the machine has not been properly

maintained and operated, its service life shall be greatly reduced. The work piece qyality is therefore affected,and the dfficiency, decreased. It is essential for an operator know how to handle the machine and the concept of its maintenance and keep correctly.

5.8.1 Daily maintenance 1. check and see if the oil level of hanf crank pump is on the designated

line.. 2. the denigmated position must be lubricated prior to operations

(Figure 7-11) 3. Keep the machine idling for three to five minutes daily priot to

operations 4. At the close of the day, work table shall be cleaned and the

unfinished work piece must be remored. A little bit of lubricant is recommended.

5. At the close of each say, all setting levers shall be loosened, and all sliding parts shall be moved to proper position. The cutter must be dismantled.

6.At the close of each day ,the head stock must be restored to its normal position if is tilted.

5.8.2 Monthly maintenance 1. Check and see if all clampinf rails of various sliding surfaced are

normal.


35

When the sliding of the rails is not smoothly. a. Use hand crank pump to pump oil. b. Check and remove the backlash between lead sctew and its nut is

normal. 2.check and see if the backlash between lead screw and its nut is

normal. When the clearance standard is below the quality reqyirements:

a. Refer to 5-6 for proper alignments, 3. check and see if the qyill lock and that of each and every sliding

syrface is normal. When worn-out occurs in the qill lock spread or loosr engagement

happens: a. Replace the bolt lever.

5.8.3 Quarterly maintenance 1. Check and see if the brake functione and belt are normal. When braking function is unusual: a. Refer to 7-3 for instructions. Replace the braking belts or other

accessoties in a proper period. b. Refer to 7-2, 7-4 and 7-5 for instruction. Replace the belts.

2. Inspect the level of work table and head stock does not attain the reqyirement.

a. Refer to 5-3.2 for alignments. b. During alignment, do not loosen totally the bolts and stain the

head stock. 3. Test the machine again by chaet of test specs .(refer tp table). 4. change the lubrication oil qyarterly. Fill new oil into when the old one

is totally cleaned. 5. Replace whatever part worn-out.


36

5.8.4.1 Head stock lubrication Lubricants Qty Time Position

1 Kuo_KUANG R 68 ESSO FEBIS K53

FULL Twice daily Head stock matchingHoles

2 TRA #2 LL TONNA 33

FULL Once daily Gear box

3 KUO_KUANG R 68 FULL 3 Daily Quill and head Internal holes

4 Yellow Grease Twice monthly Gear box


37

5.8.4.2 Machine body Lubrication Lubricants QTY time Position

1 Kuo_kuang r 68 Esso febis k53 TRA# SHELL TONNA 33

FULL Once daily Work table, saddle Slding surface and screws

2 Cutting fluid FULL As indicator shown

Figure 8-2

5.9 Warning sign Illustration 1. Do not put the hand on the taloc and do not get the workpieces while the

spindle is not totally stop. 2. Cut off the spindle power source when changing tools 3. before and after using the lifting handle, please check anf see if the clutch

gear is totally separ ated by the safety sprinf. 4. Always maintain smoothness in the qear box and tne head hole. 5. stamp a watning sign on the parts contain elestricity, cut off the power

when dismantling. 6. The machine contain safety desige, when open the electrical door, the

power will automatically cut off.


38


39

5.10 Lubrication Diagram 5.10.1 Head Lubrication Diagram


40

5.10.2 Saddle Lubrication Diagram


41

5.10.3 Base Lubrication Diagram


42


43

Chapter 7. Parts Lists 7.1 Machine Parts Diagram and Parts Lists

FOR

CB-170 CB-180 CB-185


44

(HEAD ASSEMBLY)


45

PART LIST (HEAD ASSEMBLY) ITEM PARTS NO PART NAME QTY

1 M5*12L ROUND HEAD SCREW 12 B-002 WASHER 13 B-003 FEED BEVEL PINIPN 14 B-004 FEED WORM GEAR SHAFT SLEEVE 15 B-005 WORM CRADLE BUSHING 16 M6*6L SOCKET SET SCRE 17 B-007 WORM GEAR SPACER 18 B-008 FEED DTIVE WORM GEAR 19 B-009 FEED DRIVE WORM GEAR SHAFT 110 3*3*8L FEED DRIVE GEAR JEY 111 3*3*25L KEY 212 M8*16L SOCKET SET SCREW 113 B-013 WASHER 214 3*3*8L KEY 215 B-015 FEED REVERSE BEVEL GEAR 416 B-016 FEED ENGAGE PIN 117 B-017 WORM GEAR CRADLE 118 B-018 WORM GEAR CRADLE THROW-OUT 119 B-019 SHIFT SLEEVE 120 B-020 GEAR SHIFT PLUNGER 321 B-021 COMPRESSION SPRING 122 ∮2*20L SPRINF PIN 123 B-023 SHIFT CRANK 124 1/4” BLACK PLASTIC BALL 125 M5*12 HEX-XOCKET HEAD CAP SCREW 126 B-026 KEY(NST#30 OR NST#40 ONLY) 227 B-027 CLUSTER GEAE SHAFT UPPER BUSHING` 128 B-028 CLUSTER GEAR 129 3*3*45L CLUSTER GEAR KEY 130 31 B-031 CLUSTER GEAR SHAFT 132 A-16 OUTER RETAINING RINGS 133 B-033 BEVEL GEAR BUSHING 134 B-034 BEVEL GEAR KEY 135 36 B-036 FEED DRIVING GEAR 137 3*3*20L KEY 138 B-038 CLUSTER GEAR IMPUT SHAFT 139 3*3*10L KEY 140 B-040 FEED DRIVE GEAR 141 B-066 NEEDLE BEARING 142 B-042 BUSHING 143 44 B-044 FEED WORM SHAFT BUSHING 145 46 47 48 49 B-049 FEED REVERSE BEVEL GEAR 250 B-050 FEED REVERSE CLUTCH 151 B-049 FEED REVERSE BEVEL GEAR 152


46


53 54 B-054 SET SCREW 155 B-55A REVERSE CLUTCH ROD 156 ∮3*20L SPRING PIN 157 B-057 FEED WORM SHAFT 158 59 60 B-060 FEED SHIFT ROD 161 3/16 * 1/4“ SET SCREW 162 3*3*15 KEY 163 B-063 FEED GEAR SHIFT FORK 164 CLUSTER GEAR SHIFT CRANK 165 66 B-066 CLUSTER GEAR COVER 167 M5*12L HEX-SOCKET HEAD 168 B-020 GEAR SHIFT PLUNGER 169 B-021 COMPRESSION SPRING 170 B-070 SHIFT CRANK 171 ∮3*20L SPRING PIN 172 1/4” BLACK PLASTIC BALL 173 M5*35L HEX-SOCKET HEAD CAP SCREW 274 B-074 CLUTCH RING PIN 275 B-075 CLUTCH RING 176 1/4*1/4”L SET SCREW 177 78 B-078A OVERLOAD CLUTCH LOCKNUT 179 B-079A SAFETY CLUTCH SPRING 180 B-080A OVERLOAD CLUTCH 281 B-081A OVERLOAD CLUTCH SLEEVE 282 B0-082 SPRING 183 M4*15L HEX-SOCKET HEAD CAP SCREW 384 85 M6*6L SET SCREW 186 87 M6*6L SET SCREW 188 B-088 COMPRESSION SPRING 189 B-089 KEY 190 B-090A QUILL PINION SHAFT BUSHING 191 B-091 QUILL PINION SHAFT WORM GEAR SPACER 192 B-092A OVERLOAD CLUTCH WORM GEAR 193 B-093 OVERLOAD CLUTCH RING 194 S-15 CIRCLIP 195 ∮5*15L DOWEI, PIN 196 B-096 OVERLOAD CLUTCH TRIP LEVER 197 B-097A OVERLOAD CLUTCH WASHER 198 E-7 CIRCLIP 199 B-099 CLUTCH ARM COVER 1100 1/4*1/4” HEX-SOVKET SET SCREW 1101 1/4” LOCKNUT 1102 ∮5*20L OWL PIN 1103 B-103 CAM ROD 1104 B104 TRIP HANDLE 1


47


105 1/4” BLACK PLASTIC BALL 1106 B-106 FEED TRIP BRACKET 1107 M6*20L CAP SCREW 2108 1/4*1/4L SET SCREW 1109 3*3*10L KEY 1110 B-110 FEED REVERSE KNOB STUD 1111 B-111 REVERSE KNOB 1112 E-5 CIRCLIP 1113 B-113 HANDWHEEL CLUTCH 1114 3/16” STEEL BALL 1115 B-115 COMPRESSION SPRING 1116 B-116 HANDWHEEL CLUTCH SPRING SCREW 1117 ∮3*14L SPRING PIN 1118 B-118 CAM ROD SLEEVE ASSEMBLY 1119 ∮3*12 SPRING PIN 1120 B-120 COMPRESSION SPRING 1121 B-121 TRIP PLUNGER 1122 123 B-123 TRIP PLUNGER BUSHING 1124 B-124 FEED TRIP PLUNGER 1125 B-125 HANDWEEL 1126 B-126 HANDWHEEL HANDLE 1127 B-127 SPINDLE (TAPER NST#30) 1128 B-128 QUOLL SKIRT 1129 B-129 LOCKNUT WASHER 1130 AW06 WASHER 1131 6206Z BEARING 1132 B-132 SLEEVE 1133 B-133 NOSE-PIECE 1134 B-134 SPINDLE DIRT SHIELD 1135 7207 SPINDLE BEARING 1136 B-136 BEARING SPACER(LARGE) 1137 B-137 BEARING SPACER(SALL) 1138 7207 SPINDLE BEARING 1139 140 B-140 SPECIAL SOCKET SET SCREW 1141 142 B-142 QUILL 1143 ∮3*20L SPRING PIN 1144 M4*16L SET SCREW 1145 B-145 FEED TRIP LEVER 1146 B-146 TRIP LEVER PIN 1147 B-147 INDICATOR ROD 1148 B-148B QUILL LOCK SLEEVE 1149 B-149 QUILL LOCK HANDLE 1150 M5*8L ROUND HEAD SCREW 1151 B-151 OIL STRAINER FOR QUILL BEARING 1152 153 B153A QUILL LOCK SLEEVE TAPPED 1154 B-154 INDICATOR ROD SCREW 1155 B-155 TEE BOLT 4156 B-156 LOWER CLAMPING BOLT SPACER 2


48


157 B-157 ADAPTOR NUT 4158 1/8*1/4”L ROUND HEAD SCREW 2159 B-159 MICTOMETER SCALE (INCH) 1160 S-16 CIRCLIP S-16 1161 B-161 QUILL MICRO-STOP NUT(INCH) 2162 B-162 MICRO METER MNT (INCH OR METER) 1163 B-163 QUILL STOP KNOB 1164 B-164 QUILL STOP MICRO-SCREW(INCH OR METER) 1165 3/8” HCX-SOCKET HEAD CAP SCREW 1166 B-166A QUILL PINION SHAFT 1167 168 B-168 PIN 1169 M5*12L HEX-SOCKET HEAD CAP SCREW 2170 171 3*3*18L KEY 1172 B-172 PINION SHAFT HUB SCREW 1173 3/16” STEEL BALL 1174 B-174 COMPRESSION SPRING 1175 B-175A BACK FEED HANDLE HUB 1176 B-176 PINION SHAFT HUB SLEEVE 1177 B-177 SPRING COVER 1178 B-178 CLOCK SPRING 1179 B-179 WASHER 9180 181 M6*6L SET SCREW 2182 183 B-183 REUERSE TRIP BALL LEVER 1184 B-184 FEED REVERSE TRIP PLUNGER 1185 B-185 REVERSE TRIP BALL LEVER SCREW 1186 B-186 WORM GEAR 1187 4*4*18L KEY 1188 B-188 SOCKET SET SCREW 1189 B-189 ADJ WORM SHAFT 1190 B-190 PINION SHAFT HUB HANDUL 1191 B-191 BLACK PLASTIC BALL 1192 B-192 QUILL HOUSING 1


49


50


1 1800-A016 SPINDLE MOTOR 12 1800-A018 MOTOR LOCKUNT HANDLE 23 1800-A023 MOTOR ADJ HANRLE 14 1510-G069 BLACK PLASTIC BALL HANELES 15 8*8*45L KEY 16 1800-A012 BELT HOUSING 17 300J10 TIMING BELT 18 1800-A116 MOTOR PULLEY 19 SCE 28*55 迫緊環 110 M8 HEX-SOCKER SET SCREW 111 5/8” LOCK NUT 112 1850-T086 TIMING BELT PULLEY 113 1510-T084 BEARING CAP 114 6203Z BEARING 115 5*5*15L KEY 115-1 6*6*25L KEY 116 1510-T080 BULL GEAR PINION COUNTER SHAFT17 1510-T083 COUNTER SHAFT GEAR 118 1/4” SET SCREW 119 1510-T095 SPECER 120 6203Z BEARING 121 1850-T059 BULL GEAR SHAFTER PINION 122 1510-T060 HI-LOW DETENT PLATE 123 M5*15L HEX-SOCKET SET SCREW 224 M610L SET SCREW 125 1510-T071 HI-LOW PINION BLOCK 126 1510-T070 HI-LOW SHIFT CRADK 127 1500-A046 BLACK PLASTIC BALL 1/4” DIA 128 1510-T067 SPRING 129 1510-T0666 HI-LOE DETENT PLARE 130 1510-T065 ADJ. PLATE 131 M6*16L HEX-SOCKET SET SCREW 132 1850-T036 TIMING BELT (230H) 133 M6*15L HEX-SOCKET SET SCREW 334 1800*A001 DRAWBAR 135 1800-A002 DRWBAR WASHER 136 M6 HEX-SOCKET SET SCREW 437 1800-A004 TOP BEARING CAP 138 1800-A006 LOCK NUT 139 6209ZZ BEARING 140 1800-A115 SPINDLE PULLEY 141 1800-A021 BRAKE BLOCK 142 6209ZZ BEARING 143 1800-A005 SPINDLE PULLEY HUB 144 8*7*70L KEY 145 1800-A011 BRAKE BASE 146 1850-T038 TIMING PULLEY CLUTCH SLEEVE 147 1850-T049 GEAR HOUSING 148 1800-A024 DISENGAGE FEED INSTRUCTION PLATE 149 1510-G084 SPEED CHANGE PLATE 150 RIVET 251 1850-G080 SCREW 3


51


52 M5 ELAT COUNTER-SUNK HEAD SCREW 253 1510-T051 GUINE 254 M10*25L HEX-SOCKET SET SCREW 855 M8 HEX-SOCKET SET SCREW 456 1850-T040 SPINDLE BULL GEAR ASSENBLY 157 6910ZZ DEARING 158 1850-T044 BULL GEAR BEARINF SPACER 159 1850*T043 BULL GEAR BEARINF SPACER 160 6910ZZ BEARING 161 1850-T090 WASHER 162 1850-T039 SPINDLE PULLEY HUB 163 1850*T056 BEARING LOCK NUT 164 1850*T057 BULL GEAR BEARING SLEEVE 165 1850-T048 ADJ .PLARE 166 1510-T055 SPRING 167 ∮3*25L SPRING PIN 168 ∮4*25L SPRING PIN 1


52

PART LIST (HEAD ASSEMBLY)

`


53

(X-AXIS ASSEMBLY)


54

PART LIST (X AXIS TABLE) ITEM PARTS NO PART NAME QTY

1 1700-C034 TABLE (54”) 12 170B-0126 BALL SCREW X-AXIS (INCH) 13 1500-D063 RIGHT BEARING BRACKET 14 1800-D022 BALL SCREW NUT BRACKET 15 1500-D016 DIAL (INCH0 16 1500-D005 DIAL HOLDER 17 1500-C086 DIAL LOCK NUT 18 1500-D062 LEFT BEARING BRACKET 19 170B-0147 BEARING RETAINER RING 110 1810-C007 SADDLE TABLE GIB(LEFT) 111 1500-C041 ADJUSTING SCREW 212 13 M6*15L HEX-SOCKET CAP SCEEW 314 ∮6*30L SPING PNI 415 3/8*25L HEX-SOCHET HEAD CAP SCREW 816 6204ZZ BALL BEARING 117 1/2*20UNF OLCT NUT 118 3*3*20L KEY 119 1/2*-20UNF LOCK NUT 120 M6*20L KEY 421 YSR M20P1.0 PRECISION LOCKNUT 122 7204 ANGULAR BEARING 223 1500-D016 DIAL(INCH) 124 1500-D021 DIAL HOLDER 125 1500-C086 DIAL LOCK NUT 126 1500-D026 BALL CRANK HANDLE 127 3*3*20L KEY 128 1/2*20UNF SPRING WASHER 1


55

(Y-AXIS ASSEMBLY)


56


57

PART LIST (COLUMN ASSEMBLY) 2-A, 2-B

ITEM PARTS NO PART NAME QTY 1 170B-0016 MACHINE BASE 12 1800-D038 FRONT COVER 13 170B-0128 Y-AXE BALL SCREW(INCH) 14 170B-0147 BEARING RETAINER RING 15 1500-D064 CROSS FEED BEARING BRACKET 16 1800-C052 SADDLE 17 1500-C041 ADJUSTING SCREW 68 1810-C005 SADDLE KNEE GIB 39 1800-D022 FEED NUT BRACKET 110 220B-0090 CHIP GUARD (1) 111 220B-0091 CHIP GUARD (2) 112 220B-0092 CHIP GUARD (3) 113 220B-0093 CHIP GUARD (4) 114 1800-C064 RIGHT GUIDE PLATE OF SADDLE 115 1800-C021 RIGHT HAND TURCITE-B 116 1800-C044 FELT WIPER(FRONT & REAR) 217 1800-C202 BALL BEARING(LEFT) 118 1800-C063 LEFT GUIDE PLATE OF SADDLE 119 1800-C050 UPPER BASE-SADDLE WIPER 220 M6*15L HEX-SOCKET CAP SCREW 321 YSR M20P1.0 PRECISION LOCK NUT 122 23 7204 ANGULAR BEARING 224 M10*20L HEX-SCOKET CAP SCREW 425 M12*35L HEX-SCOKET CAP SCREW 826 M6*20L HEX-SCOKET CAP SCREW 427 M5*12L ROUND HEAD CROSS SCREW 428 3/8*30L HEX-SOCKET CAP SCREW 429 ∮6*30L SPRING PIN 230 3/16*12L ROUND HEAD CROSS SCREW 1031 1500-D016 DIAL (INCH) 132 1500-D021 DIAL HOLDER 133 1500-C086 DIAL LOCK NUT 134 1500-D026 BALL CRANR HANDLE 135 1/2”-20UNF SPRING WASHER 136 1/2”-20UNF LOCK NUT 1


58

(Z-AXIS COLUMN ASSEMBLY)


59

(Z-AXIS COLUMN ASSEMBLY)


60

PART LIST (Z-AXIS COLUMN ASSEMBLY) ITEM PARTS NO PART NAME QTY

1 170B-0011A COLUHN 12 220B-0108 BEARING CAP (T0P) 13 220B-0103B BEARING CAP (BOTTOM) 14 220B-0109A BRACKET 15 170B-0001 HEAD BRACKET 16 170B-0002 LEFT GUIDE PLATE OF HEAD BRACKER 17 170B-0003 RIGHT GUIDE PLATE OF HEAD BRACKET 18 170B-0008 WEIGHT DEVICE BRACKET 19 170B-0009 MOTOR BRACKET 110 220B-0104B PRELOAD SCREW 111 220B-0107 Z-AXE BALL SCREW 112 220B-0028 CHIP GUARD (UP) 113 220B-0029 CHIP GUARD (MIDDLE) 114 220B-0030 CHIP GUARD (DOWN) 115 170B-0004 STEEL PLTE 116 2200-2022 RIGHT HAND BRACKET WIPER 117 170N-0027 RIGHT HAND TURCITE-B OF BRACKET 118 170B-0028 LEFT HAND TURCITE-B OF BRACKET 119 2200-2022 LEFT HAND BRACKET WIPER 120 1500-C041 ADJUSTING SCREW 621 220B-0007 HEAD BRACKET GIB 322 M6*25L HEX SOCKET CAP SCREW 223 6205ZZ BALL BEARING 124 M6*25L HEX SOCKET CAP SCREW 425 M128*35L HEX SOCKET CAP SCREW 826 S-25 RETAINING RING 127 R-52 RETAINING RING 128 M8*30L HEX SOCKET CAP SCREW 429 M6*30L HEX SOCKET CAP SCREW 430 M8*30L HEX SOCKET CAP SCREW 331 YSR-25 PRECISION NUT 132 25TAC SUPPORT BEARING 233 OIL SEAL 134 M4*10L ROUND HEAD CROSS CREW 435 M6*10L ROUND HEAD CROSS CREW 236 3/16”*12L ROUND HEAD CROSS CREW 12


61


62


63

PART LIST (Z-AXIS COLUMN ASSEMBLY) ITEM PARTS NO PART NAME QTY

1 170B-0008 WEIGHT DEVICE BRACKET 12 170B-0009 MOTOR BRACKET 13 220B-0022 BEARING CAP (RIGHT) 24 220B-0024 BEARING CAP (LEFT0 25 220B-0021 CHAIN PULLEY SHAFT 26 220B-0013 CHAIN PULLEY 47 220B-0017 BEARING 48 220B-0014 SPECER 29 220B-0023 BEARING COVER 210 170B-0010A WEIGHT DEVICE 111 220B-0011 CHAIN 212 M6*15L HEX-SOCKET CAP SCREW 1213 M6*10L HEX-SOCKET CAP SCREW 614 M4*15L HEX-SOCKET CAP SCREW 1215 S-20 RETAINING RING 216 R-47 RETAINING RING 217 6204ZZ BALL BEARING 418 S-25 RETAINING RING 219 TAF 253820 NEEDLE BEARING 420 M6*30L HEX-SOCKET CAP SCREW 4


64

7.2 Machine Parts Diagram and Parts Lists (FOR CB-410) 1. Hard part drawing 2. Table and saddle part drawing 3. Base part drawing

4. Boby part drawing


65


66


1 2200-1001 HEAD HOUSING 12 2200-1003 QUILL 13 1800-B129 LOCK NUT 14 M6*15L HEX-SOCKET SCREW 15 7210ACP4DB ANGULAR BALL BEARING 16 1800-B137 BERING SPECER (INNER COLLAR) 17 1800-B136 BERING SPECER (OUTTER ) 18 7210ACP4DB ANGULAR BALL BEARING 19 2200-1004 NOSE-PIECE 110 1800-B134 SPINDLE DIRT SHIELD 111 M5*8L SET SCREW 212 1800-B127 SPINDLE 113 1500-B026 KEY 214 5/16*3/4” HEX-SOCKET SCREW 215 M5*15L ELAT HEAD SCREW 416 2200-1037 BEARING COVER 117 6002ZZ BALL BEARING 118 6002ZZ BALL BEARING 119 2200-1022 BACK GEARE 120 S-28 SNAP RING 321 2200-1021 SPLINED SHSET 122 R-68 SNAP RING 123 6909ZZ BALL BEARING 124 2200-1023 BEARING SUPPORT RING 125 S-45 SNAP RING 126 2200-1020 COUNT SHAET GEAR 127 30204 TAPER ROLLER BEARINGEW 128 6009ZZ BALL BEARING 129 1810-D034 TAPER RLOOER VEARINGEW 230 2200-1030 BEARING HOUSING 131 M8*35L HEX-SOCKER SCREW 132 7*7*50L KEY 133 2200-1029 SPINDLE PULLEY HUB 134 2200-1028 WORD SHAEW 135 R-68 SNAP RING 136 2200-1025 BEARING CAP 137 6909ZZ BALL BEARING 138 M6 HEX-SOCKET SCREW 339 S-45 SNAP RING 140 2200-1024 SPINDLE GEAR 141 S-45 SNAP RING 142 2200-1024 SPINDLE GEAR 143 M8*20L HEX-SOCKET SCREW 344 2200-1018 BEARING HOUSING 145 6009ZZ BALL BEARING 146 R-75 SNAP RING 147 S-40 SNAP RING 148 6208ZZ BALL BEARING 149 M5*15L ELAT HEAD SCREN 450 2200-1063 BEARING CAP 151 30203 RAPER ROLLER BEARING 152 2200-1062 BEARING HOUSING 1


67


53 6003ZZ BALL BEARING 254 2200-1061 BACK GEAR SPLING SHAET 155 S-17 SANP RING 156 5*5*35 KEY 157 ∮20*35 OIL SEAL (G TYPE) 158 2200-1036 SPINDLE MOTOR 159 2200-1057 HEX-SOCKET 160 7*7*50 KEY 161 B-37 V BELT 162 2200-1034 MOTOR PULLEY 163 1500-A044 MOTOR PULLEY WASHER 164 M8*15L HEX-SOCKET SCREW 165 M8*30L HEX-SOCKET SCREW 666 2200-1002 BELT HOUSING 167 M6*15L HEX-SOCKET SCREW 368 2200-1031 BEARING COVER 169 1800-A003 DRNW BAR 170 1800-A002 DRAWBAR WASHER 171 AN09 LOCK NUT 172 AN09 WASHER 173 6209ZZ BALL BEARING 174 M8*20L HEX-SOCKET SCREW 775 2200-1038 TOP BEARING COVER 176 2200-1033 SPINDLE PULLEY 177 M6*15L HEX-SOCKET SCREW 478 2200-1080 BEARING COVER 179 2200-1039 BRAKE SHOE 180 2200-1040 BRAKE SHOE PIN 281 S10 SNAP RING 282 2200-1046 BRAKE SLEEVE 183 2200-1045 SPRING 184 2200-1044 CHAIN ADJUSTING SCREW 185 2200-1043 ROLLER CHAIN 186 2200-1041 BRAKE LOCK SHAET 187 M5*10L HEX-SOCKET SCREW 288 M5 WASHER 189 2200-1051 SPRING 190 ∮1/4” SREEL BALL 191 2200-1054 BRAKE POSITION PLATE 192 ∮2.0 RIVET 293 M3 ROUND HEAD SCREW 494 MICRO-SWITCH 295 2200-1047 BRAKE SLIDE 196 2200-1048 BRAKE SLIDE SUPPORT PIN 297 2200-1052 BRAKE SEAT 198 1810-D028 BRAKE HANDLE HUB 199 2200-1055 BRAKE HANDLE 1100 1510-G069 PLASTIC HANDLE 1101 2200-1053 INDICATOR PLATE 1102 ∮2.0 RINVET 2


68


69


1 2200-1027 EORK PORT 12 2200-1026 BACKGEAR EORK 13 2200-1068 ECCENTRIC SHAET 14 2200-1065 “H-L” COVER 15 ∮1/4” STEEL BALL 16 2200-1051 SPRING 17 2200-1066 DIAL 18 2200-1053 DIAL INDICATING PLATE 19 M6*15L HEX-SOCKET SCREW 210 2200-1069 “H-L”INDICATING PLATE 111 2200-1118 PLASTIC HANDLE 112 2200-1117 PINION SHAET HUB HANDLE 113 2200-1115 PINION SHAET HUB SLEEVE 114 2200-1116 BACK FEED HANDLE HUB 115 2200-1084 PINION SHAET HUB SCREW 116 ∮5*15L PIN 117 2200-105 WARW INDICATOR 118 ∮2.0 PLATE 419 2200-1113 RIVET 120 2200-1112 SPRING COVER 121 M6*15L HEX-SOCKET SCREW 222 M6*10L SET SCREW 123 1500-B140 SPECIAL SOCKET SCREW 224 M6*25L HEX-SOCKET SCREW 225 2200-1005 QUILL STOP KNOB 126 2200-1006 QUILL STOP MICRO SCREW 127 S-18 SNAP RING 128 2200-1009 MICRO NETER NUT 129 2200-1010 MICRO-STOP NUT 130 M4*10L ROUND HEAD SCREW 231 2200-1133 MICRO NETER SCALE 132 2200-1016 DUST GUARD 133 2200-1015 QUILL COVER 134 2200-1158 DUST PROOE SUPPORT PIN 235 M4*10L ROUND HEAD SCREW 236 2200-1121 SPRING 137 38 2200-1122 TRIP PLUGER 139 M4 NUT 240 M4*25L HEX-SOCKET SCREW 241 2200-1124 FEED DISENGAGE LEVER 142 2200-1056 PLASTIC HANDLE 143 S-10 SNAP RING 144 2200-1130 PAD 145 2200-1128 QUILL LOCK SLEEVE 146 2200-1129 BOLT 147 2200-1127 QUILL LOCK SLEEVE TAPPED 148 2200-1126 QUILL LOCK LEVER 149 6000ZZ BALL SCREW 350 2200-1079 WORN SHAET 1



70


51 5*5*12L KEY 152 5*5*20L KEY 153 2200-1078 GEAR 154 2200-1081 WORM SHAET BEARING HOUSING 155 5202 BALL BEARING 156 R-35 SNAP RING 157 2200-1082 SPACER 158 220-1088 MICROFEED PLATE 159 M4*10L ROUND HEAD SCREW 560 2200-1087 MICRODIAL SCREW 161 2200-1085 MICRODIAL 162 2200-1083 MICROFEED HANDWHEEL 163 AN02 LOCK NUT 164 FT-60 PLASTIC HANDLE 165 2200-1142 SPACER 166 2200-1141 FEED GEAR 167 2200-1076 FEED GEAR 168 3*3*15L KEY 169 3*3*15L KEY 170 2200-1076 FEED GEAR 171 2200-1077 FEED GEAR 172 6000ZZ BALL BEARING 173 2200-1075 BEARING COVER 174 2200-1074 SPACER 175 6000ZZ BALL VEARING 176 2200-1072 GEAR 177 2200-1071 SLIDING GEAR SHAET 178 4*4*45L KEY 179 4*4*12L KEY 180 2200-1070 WORN GEAR 181 2200-1092 SHIET CRANK SCREW 182 2200-1090 FEED SHIET FORK 183 ∮4*10L SPRING PIN 184 2200-1091 SHIET CRANK 185 2200-1094 ECCENTRIC SHAET 186 2200-1093 POWER FEED COVER 187 2200-1051 SPRING 188 2200-1095 FEED CLUTCK INDICATING PLARE 189 2200-1066 DIAL 190 ∮4*40L SPRING PIN 191 2200-1053 DIAL INDICATING PLATE 192 2200-1056 PLASTIC HANDLE 193 2200-1124 FEED ENGAGE LEVER 194 2200-1119 CAM ROD 195 2200-1120 CAM ROD PIN 196 E-3 SNAP RING 297 2200-1105 OVERLOAD CLUTCH TRIP LEVER 198 2200-1108 BALL HEAD PIN 199 2200-1107 SPRING 1100 2200-1110 QUILL PINION SHAET BUSING 1


71


101 1810-C001 TABLE 1102 1500-D046 WORM GEAR 1103 2200-1098 WORM GEAR SLEEVE 1104 2200-1100 CLUTCH SHAET 1105 2200-1099 OVERLOAD CLUTCH 1106 2200-1101 SAFETY CLUTCH SPRING 1107 2200-1102 ADJUSTING NUT 1108 M6 SET SCREW 1109 2200-1106 OVERLOAD CLUTCH TRIP LEVER BRACKET 1110 M4*10L HEX-SCOCKET SCREW 2111 ∮5*25L SPRING PIN 1112 2200-1104 SET SCREW 1113 2200-1103 OVERLOAD CLUTCH TRIP LEVER BUSH 1114 5*5*25L KEY 115 S-16 SNAP RING 1116 S-20 SNAP RING 1117 2200-1115 PINION SHAET SLEEVE 1118 S-20 SNAP RING 1119 2200-1109 TRIP LEVER COVER 1120 7002 ANGULAR BEARING 1121 M8 NUT 1122 M8*30L SET SCREW 1123 2200-1159 BEARING LOCKING RING 1124 2200-1060 SPACER 1125 M6 HEX-SOCKET SCREW 1126 M4*10L ROUND HEAD SCREW 2127 2200-1053 INDICATOR PLATE 1128 2200-1066 CRANK HANDLE 1129 2200-1051 SPRING 1130 ∮1/4” STEEL BELL 1131 2200-1065 PRWER FEED COVER 1132 2200-1064 ECENTRIC SHAET 1133 134 2200-1060 FEED GEAR 1135 ∮4*40L SPRING PIN 1136 M4*10L HEX-SOCKET INDICATING PLATE 2137 2200-1067 FEED CLUTCH INDICATING PLATE 1138 2200-2001 WORMJ GEAR 1139 M8 HEX-SOCKET SCREW 6


72


73


1 1810-C001 TABLE 12 1500-D046 T-TYPE PLASTIC 63 M8 CAP SCREW 44 1810-C012 SUB TABLE 25 1810-D04 BEANING SPACER RING 16 R-52 SNAP RING 17 6304 ZZ BALL BEARING 18 6304 ZZ BALL BEARING 19 1810-D047 RIMING BELT PULLEY 110 M5*12L CAP SCREW 311 1810-C022 “A”SHAFT SIDE COVER 112 1810-D023 SET SHEET 113 M6 CAP SCREW 114 AN04 NUT 215 AW04 WADHER 416 1810-D007 BEARING SPACER RING 117 1810-D050 TIMING BELT PULLEY SIDE COVER 118 1810-C021 TIMING BELT 119 1810-D048 TIMING BELT PULLLEY 120 1810-C023 TIMING RING 121 1810-D049 TIMING BELT PULLEY SIDE COVER 122 1810-D011 TIGHTLY RING COVER 123 M5*10L CAP SCREW 424 M6*10L CAP SCREW 325 1810-D009 BEARING SEAT 126 S-15 SNAP RING 127 6202 ZZ BALL BEARING 128 M5 CAP SCREW 629 1810-D008 FIXED COVER SIDE SEAT 130 M10*30L CAP SCREW 531 M10-30L CAP SCREW 432 1810-D002 X-AXLE SET SEAT 133 AN05 NUT 134 AW05 WASHER 135 M10*30L CAP SCREW 336 1810-D003 BEARING FIXED SEAT 137 32005 CONICAL BALL BEARING 138 32005 CONICAL BALL BEARING 139 2200-2125 SERVO-MOTOR 140 1800-A112 MOTOR SHIFTING SEAT 141 M6 CAP SCREW 242 3/8” HEXAGON BOLT 143 3/8 HEXAGON NUT 144 1800-A113 SUPPORT 145 M6 CAP SCREW 246 1810-D029 DAMPER 447 M4 CUP HEAD CROSS SCREW 1648 M6 CAP SCREW 249 2200-2120 SET RULER 250 2200-2119 X-AXLE STROKE SET RAM 251 M6*15L CAP SCREW 452 5*5*25L KEY 1


74


53 M8 NUT 654 1810-D062 BOLT 255 1810-C008 TABLE INSERT BAR 156 M6 CAP SCREW 457 2200-2123 X-AXLE BALL WORM 158 8*7*30L KEY 159 M10 CAP SCREW 460 1810-D012 NUT FIXED SEAT 161 2200-2193 WORM WHEEL 162 2200-2192 SPACER RING 163 2200-2101 LEFT SIDE GEAR BOX 164 M8*25L CAP SCREW 465 6204 ZZ BALL BEARING 166 AW04 WASHER 167 AN04 NUT 168 1810-D015 BEARING COVER 169 M6*20L CAP SCREW 370 2200-2103 GEAR BOX COVER 171 M6 ROUND HEAD SCRRW 472 AN04 NUT 173 AW04 WASHER 174 2200-2193 WORM WHEEL 175 2200-2102 SPACER RING 176 6205 ZZ BALL BEARING 177 2200-2105 SETTING SEAT 178 2200-2113 GRADUATION RING INDICATOR 179 M8 CAP SCRRW 480 1810-D034 TAPER PIN 281 5*5*25L TWIN-HEAD ROUND KEY 182 2200-2104 MANDREL 183 8*7*25L TEIN-HEAD ROUND KEY 184 2200-2109 TIGHTLY RING 185 2200-2114 SET HANDLE 186 M8*20L SET SCREW 187 2200-2110 BLAKING RING 188 6305 ZZ BALL BEARING 189 ∮5*50L SPRING PIN 190 2200-2106 CLUTCH 191 2200-2112 FIXED SCREW 192 2200-2108 GRADUATION RING 193 2200-2116 SPRING 194 2200-2107 X-AXLE HAND WHEEL 195 2200-2117 HANDLE 196 2200-2111 HAND WHEEL SET RING 197 M8*20L CAP SCREW 198 2200-2128 SADDLE 199 1700-C045 INSERT BAR BRAKING RULER 2100 2200-1057 HANDLE 1101 2200-2122 LIMIT SWITCH 1102 2200-2118 LIMIT SWITCH SEAT 1103 M5 CAP SCREW 2104 1500-C041 INSERT BAR ADJUSTING SCREW 2


75


105 2200-2153 SADDLE INSERT BAR 1106 2200-2155 SADDLE LEFT GUIDE PLATE 1107 M12*35L CAP SCREW 4108 2200-2153 SADDLE INSERT BAR 2109 M12*35L CAP SCREW 4110 2200-2156 SADDLE RGHTN GUIDE PLATE 1111 1500-C041 INSERT BAR ADJUSTING SCREW 2112 2200-2165 SCRAPER 2113 M5*15L CUP HEAD CROSS SCREW 28114 M10 CAP SCREW 4115 2200-2160 NUT SET SEAT 1116 1810-D030 INSERT BAR SETTING RULER 2117 1810-C007 TABLE INSERT BAR 1


76


77


1 M10*30L CAP SCREW 42 2200-2160 NUT FIXED SEAT 13 220B-0052 TOP DUST PROOF COVER 14 220B-0053 MIDDLE DUST PROOF COVER 15 220B-0054 BOTTOM DUST PROOF COVER 16 220B-0055 BASE 17 M6*20L CAP SCREW 68 2200-2041 BASE SIDE COVER 19 M5*10L CUP HEAD CROSS SCRE 210 1500-C130 OIL FILTER 111 M6*10L CAP SCREW 412 220B-0056 BASE SIDE COVER 113 M6*20L CAP SCREW 414 2200-2216 ELECTRICAL WIRE FIXED SEAT 115 2200-2042 HORIZONTAL ADJUSTING SCREW 616 2200-2052 SET NUT 617 M6 CAP SCREW 318 220B-0081 Z-ACLE BACK BEARING SEAT 119 1/8*PT OIL INJECROR 120 PB20 SPHERICAL BEARING 121 6#*50L TAPER OIN 122 220B-0073 WORM WHEEL 123 220B-0072 Z-AXLE GEAR SHAFT 124 220B-0013 CHAIN WHEEL 125 32005 CONICAL ROLLER BEARING 126 220B-0067 BEARING SET SEAT 127 32005 CORICAL ROLLER BEARING 128 AW05 WASHER 129 AN05 NUT 130 M8*35L CAP SCREW 331 5*5*20L TEIN-HEAD ROUND KEY 432 AN05 NUT 133 AW05 WASHER 134 220B-0013 CHAIN WHEEL 135 32005 CONICAL ROLLER BEARING 136 220B-0075 BEARING SET SEAT 137 32005 CONICAL BALL BEARING 138 M10*35L CAP SCREW 339 220B-0076 SUB-SHAFT 140 5*5*20L TWIN-HEAD ROUND KEY 141 2200-2120 SET RULER 142 220B-0178 STROKE SETTING RULER 243 M6 FLAT HEAD SCEREW 244 M10*30L CAP SCREW 245 750W SERVR-MOTOR 146 M6*20L CAP SCREW 247 1800-A112 MOTOR SHIFTING SEAT 148 220B-0059 Y.Z GEAR BOX 149 1800-A113 SUPPORT PLATE 150 3/8” NUT 151 3/8*70L HEXAGON HEAD SREW 152 M6*20L CAP SCREW 2


78


53 M8*30L CAP SCREW 454 1810-D049 TOOTH-TYPE BELT WHEEL 155 1810-D048 TOOTH-TYPE BELT WHEEL 156 1810-D049 TOOTH-TYPE BELT WHEEL 157 1810-D011 TIFHTLY RING COVER 158 M4*15L CAP SCREW 459 1810-D004 BEARING SPACER RIN G 160 R-52 RETAINING RING 161 6304 ZZ DEEP GROOVE BALL BEARING 262 1810-D047 TOOTH-TYPE BELT WHEEL 163 M5*15L CAP SCREW 364 1810-D007 BEARING SPACER RING 165 220B-0065 CLUTCH SUPPORT 166 NC-2.5T ELECTRICAL CLUTCH 167 220B-0068 SPACER RING 168 6204 ZZ BALL BEARING 169 1810-D042A FIXED HANDLE 170 1810-D044A FIXED SCREW 171 220B-0069 BEARING SEAT 172 M6*20L CAP SCREW 373 2200-2109 TIGHTLY RING 174 1810-D043A LOCKING BUSH 175 220B-0070 SPACER RING 176 AW04 WASHER 177 AN04 NUT 178 220B-0071 DUST PROOF COVER 179 M6*25L CAP SCREW 280 81 2200-2188 SET SEAT 182 M6*30L CAP SCREW 483 2200-2198 GRADUATION RING INDICATO 184 6205 ZZ44 DEEP GROOVE BALL VEARIN 185 ∮5.0 SPRING PIN 186 2200-2016 CLUTCH 187 2200-2108 GRADUATION TING 188 2200-2112 FIXED SCREW 189 2200-2116 SPRING 190 2200-2157 Y-AXLE HAND WHEEL 191 1800-C083 HANDLE 192 2200-2111 HANDLE WHEEL FIXED RING 193 M8*20L CAP SCREW 194 M8*20L CAP SCREW 195 2200-2111 HANDLE WHEEL FIXED RING 196 2200-2107 X-AXLE HAND EHEEL 197 1800-C083 HANDLE 198 2200-2116 SPRING 199 2200-2108 GRADUATION RING 1100 2200-2112 SET SCREW 1101 2200-2106 CLUTCH 1102 ∮5.0 SPRING PIN 1103 6305 ZZ DEEP GROOVE BALL BEARING 1104 2200-2110 BLAKING RING 1


79


105 2200-2109 TIGHTLY RING106 M6*25L CAP SCREW107 2200-2115 SET SCREW108 2200-2113 GRADUATION RING INDICATOR109 220B-0063 SET SEAT 110 2200-2114 SET HANDLE111 6006 ZZ DEEP GROOVE BALL BEARING112 220B-0062 MANDREL113 5*5*25L TWIN-HEAD ROUND KEY114 M6*15L CAP SCREW115 1810-D009 BEARING SEAT116 6202 ZZ DEEP GROOVE BALL BEARING117 M6*30L CAP SCREW118 220B-0060 Y.Z GEAR BOX COVER119 AN04 NUT 120 AW04 WASHER121 NC-2.5T ELECTRICMAGNETIC CLUTCH122 220B-0065 CLUTCH SUPPORT123 M5*15L CAP SCREW124 1810-D007 BEATING SPACER RING125 1810-D047 TOOTH TYPE BELT WHEEL126 220B-0077 TOOTH TYPE BELT127 6304 ZZ DEEP GROOVE BALL BEARING128 R-52 RETAINING RING129 1810-D004 BEARING SPACER RING130 6204 ZZ DEEP GROOVE BALL BEARING131 AN04 NUT 132 AW04 EASHER133 32005 CONICAL ROLLER BEARING134 M10*35L CAP SCREW135 1810-D003 BEARING FIXED SEAT136 32005 CONICAL BALL VEARING137 220B-0066 CHAIN 138 220B-0013 CHAIN WHEEL139 5*5*20L TWIN-HEAD ROUND KEY 140 141 ∮4 SPRING PIN142 143 5*5*25L TWIN-HEAD ROUND KEY144 2200-2151 Y-AXLE BALL BAARING145 AN05 NUT 146 AW05 WASHER147 32005 CONICAL BALL BEARING 148 M10*35L CHAIN WHEEL149 1810-D003 BEARING FIXED SEAT150 32005 CONICAL BALL BEARING151 220B-0013 CHAIN WHEEL152 S-15 RETAINING RING153 220B-0064 SUB-SHAFT154 5*5*20L TWIN-HEAD ROUND KEY


80


81


1 M6*10L CUP HEAD CROSS SCRE 42 220B-0018 BALANCE WEIGHT SUPPORT COVER 13 M8*30L CAP SCREW 44 220B-0020 BALANCE WEIGHT SUPPORT SEAT 15 S-25 RETAINING RING 16 220B-0014 SPACER RING 17 220B-0013 CHAIN WHEEL 28 TAFI253820 PIN EYPE BEATING 29 220B-0017 BEARING SET SHEET 210 M4 CAP SCREW 311 M4 CAP SCREW 312 220B-0017 BEATING DIXED SHEET 213 TAFI253820 PIN TYPE BEATING 214 220B-0013 CHAIN WHEEL 215 220B-0014 SPACER RING 216 S-25 RETAINING RING 117 S-25 RETAINING RING 118 220B-0027 BEARING COVER 119 M6*15L CAP SCREW 320 M6*15L CAP SCREW 621 220B-0024 BEARING SEAT 222 6204 ZZ BALL BEARING 223 220B-0021 MANDREL 224 220B-0022 BEARING SEAT 225 6204 ZZ BALL BEARING 226 R-47 RETAINING RING 227 220B-0023 BEARING SEAT 228 220B-0026 Z-AXLE TOP BEARING SEAT 129 6205 ZZ BALL BEATING 130 220B-0003 Z-AXLE BALL BEATING 131 M6 CAP SCREW 332 5*5*30L TWIN-HEAD ROUNND KEY 133 220B-0011 BALANCE WEIGHT CHAIN 234 1/2” JOINT 235 1/2” JOINT 236 220B-0006 CHAIN BOLT 237 220B-0008 SUPPORT COVER 138 M4*10L CUP HEAD CROSS SCREW 439 M6*20L CAP SCREW 340 2200-2007 BEARING SEAT 141 S-20 RETAINING SEAT 142 6204 ZZ BALL BEATING 143 M16 HEAD SUPPORT 444 2200-2006 PLAIN WASHER 445 220B-0001 HEAD SUPPORT 146 M6*10L CAP SCREW 447 220B-0047 BOTTOM DISRRIBUTION CASE 148 2200-2012 HEAD SET BOLT 449 220B-0005 SUPPORT SIDE PLATE 150 M4*10L CUP HEAD CROSS SCREW 451 220B-0002 HEAD INCLINED WORM 152 51105 THRUST BALL BEATING 153 2200-2004 BEARING SEAT 154 51105 THRUST BALL BEARING 155 M6*20L CAP SCREW 356 AW05 WASHER 1



82

ITEM PARTS NO PART NAME QTY

57 AN05 NUT 158 2200-2005 BEARING COVER 159 160 161 M4*15L CAP SCREW 162 2200-223 LIMIT SEITCH SEAT 163 M5 CAP SCREW 164 220B-0007 SUPPORT INDERT BAR 165 2200-2159 ROTATING HANDLE 166 1500-C041 INSERT ADJUSTING SCREW 167 220B-0009 SUPPORT LEFT GUIDE PLAT 268 2200-2158 FIX STEM 169 M12*45L CAP SCREW 470 220B-0028 TOP DUST PROOF PLATE 171 220B-0029 MIDDLE DUST PROOF PLAT 172 220B-0030 BOTTOM DUST PROOF PLATE 173 M6*10L CUP HEAD CROSS SCREW 274 220B-0007 SUPPORT INSERT BAR 175 1500-C041 INSERT BAR ADJUSTING SCRE 276 M12*45L CAP SCREW 477 220B-0010 SUPPORT RIGHT GUIDE PLATE 178 LIMIT SEITCH 179 M5*20L CAP SCREW 480 2200-2120 SET RULER 281 220B-0034 Z-AXLE BLAKING BLOCK 182 M6*30L CAP SCREW 283 220B-0048 STEEL PLATE 184 M6 CAP SCREW 685 M6 CAP SCREW 486 220B-0046 TOP EIRE BOX 187 220B-0007 SUPPORT INSERT BAR 188 220B-0025 RAM 189 35DX55DX11B SEAL 190 32005 CONICAL ROLLER BEARING 191 M8*25L CAP SCREW 392 220B-0033 Z-AXLE DOWN BEARING 193 32005 CONICAL ROLLER BEARING 194 220B-0073 WORM WHEEL 195 AW05 WASHER 196 AN05 NUT 197 M20*80L CAP SCREW 898 M20 SPRING WASHER 899 220B-0012 BALANCE WEIGHT CHAIN 1100 220B-0006 JOINT 2101 1/2” COOLING PUMP 1102 1/2” CAP SCREW 2103 220B-0011 BASE LACK COVER 2104 1/2” JOINT 2105 1/8HP*150L COOLING PUMP 1106 M6 CAP SCREW 4107 2200-2051 BASE BACK COVER 1108 M6 CUP HEAD CROSS SCREW 4109 220B-0057 PUMP SUPPORT PLATE 1

Chapter 7. Lubrication Diagram


83

Base Lubrication Diagram


84


85

Head Lubrication Diagram


86

CB170 ,CB180 ,CB185


87

CB-410

manford machinery co., ltd - milling machine,bed … operationmanu… · manford machinery co., ltd...

Documents