list manual g120c - siemens · 12 list manual (lh13), 04/2015, a5e33840768 2.1 overview of...

s

SINAMICSSINAMICS G120C

List Manual

04/2015Edition

Answers for industry.

s

04/2015A5E33840768

SINAMICS

SINAMICS G120C

List Manual

Fundamental safety instructions 1

Parameters 2

Function diagrams 3

Faults and alarms 4

Appendix A

Index

Valid forDrive Firmware versionSINAMICS G120C 4.7 SP3

Warning conceptThis Manual contains information which you must observe to ensure your own personal safety as well as to avoid material damage. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to equipment damage have no safety alert symbol. Depending on the hazard level, warnings are indicated in a descending order as follows:

If more than one level of danger is simultaneously applicable, the warning notice for the highest level is used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified personnelThe product/system described in this documentation may only be operated by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens productsNote the following:

TrademarksAll names identified with ® are registered trademarks of Siemens AG. Any other names used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of liabilityWe have verified that the contents of this document correspond to the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. The information given in this document is reviewed at regular intervals and any corrections that might be necessary are made in the subsequent editions.

DANGERindicates that death or serious injury will result if proper precautions are not taken.

WARNINGindicates that death or serious injury could result if proper precautions are not taken.

CAUTIONindicates that minor personal injury can result if proper precautions are not taken.

NOTICEindicates that property damage can result if proper precautions are not taken.

WARNINGSiemens products are only permitted to be used for the applications envisaged in the catalog and in the associated technical documentation. If third-party products and components are to be used, they must be recommended or approved by Siemens. These products can only function correctly and safely if they are transported, stored, set up, mounted, installed, commissioned, operated and maintained correctly. The permissible ambient conditions must be adhered to. Information in the associated documentation must be observed.

Siemens AGDivision Digital FactoryPostfach 48 4890026 NUREMBERGGERMANY

Document order number: A5E3384076804/2015 Subject to change

Copyright © Siemens AG 2014 - 2015.All rights reserved

Legal information

SINAMICS G120CList Manual (LH13), 04/2015, A5E33840768 5

Table of contents

1 Fundamental safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.1 General safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.2 Industrial security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Overview of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.1.1 Explanation of the parameter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.1.2 Number ranges of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.2 List of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.3 Parameters for data sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3362.3.1 Command Data Sets (CDS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3362.3.2 Drive Data Sets (DDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3372.3.3 Motor data sets (MDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3412.3.4 Power unit Data Sets (PDS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3432.3.5 Encoder Data Sets (EDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343

2.4 BICO parameters (connectors/binectors). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3442.4.1 Binector inputs (BI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3442.4.2 Connector inputs (CI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452.4.3 Binector outputs (BO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452.4.4 Connector outputs (CO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3462.4.5 Connector/binector outputs (CO/BO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

2.5 Parameters for write protection and know-how protection . . . . . . . . . . . . . . . . . . . . . . . . . . 3502.5.1 Parameters with "WRITE_NO_LOCK". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3502.5.2 Parameters with "KHP_WRITE_NO_LOCK" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3502.5.3 Parameters with "KHP_ACTIVE_READ" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351

2.6 Quick commissioning (p0010 = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352

3 Function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

3.1 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356

3.2 Explanations on the function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361

3.3 Input/output terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366

3.4 PROFIenergy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375

3.5 PROFIdrive communication (PROFIBUS/PROFINET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

3.6 CANopen communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

3.7 Communication, fieldbus interface (USS, MODBUS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399

3.8 Internal control/status words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405

3.9 Brake control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

3.10 Safety Integrated Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425

3.11 Safety Integrated PROFIsafe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

Table of contents

SINAMICS G120C6 List Manual (LH13), 04/2015, A5E33840768

3.12 Setpoint channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

3.13 Vector control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442

3.14 Vector control, Standard Drive Control (p0096 = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467

3.15 Vector control, Dynamic Drive Control (p0096 = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473

3.16 Technology functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490

3.17 Technology controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492

3.18 Signals and monitoring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497

3.19 Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507

3.20 Data sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513

4 Faults and alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517

4.1 Overview of faults and alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5184.1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5184.1.2 Explanation of the list of faults and alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5224.1.3 Number ranges of faults and alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527

4.2 List of faults and alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529

A Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617

A.1 ASCII table (characters that can be displayed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618

A.2 List of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631

1


Fundamental safety instructions

Content

1.1 General safety instructions 8

1.2 Industrial security 9

1 Fundamental safety instructions1.1 General safety instructions


1.1 General safety instructions

WARNINGRisk of death if the safety instructions and remaining risks are not carefully observed

If the safety instructions and residual risks are not observed in the associated hardware documentation, accidents involving severe injuries or death can occur.

• Observe the safety instructions given in the hardware documentation.

• Consider the residual risks for the risk evaluation.

WARNINGDanger to life or malfunctions of the machine as a result of incorrect or changed parameterization

As a result of incorrect or changed parameterization, machines can malfunction, which in turn can lead to injuries or death.

• Protect the parameterization (parameter assignments) against unauthorized access.

• Respond to possible malfunctions by applying suitable measures (e.g. EMERGENCY-STOP or EMERGENCY-OFF).


1 Fundamental safety instructions1.2 Industrial security

1.2 Industrial security

Note

Industrial security

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, devices, and/or networks. They are important components of a holistic industrial security concept. With this in mind, Siemens’ products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

To ensure that Siemens products and solutions are operated securely, suitable preventive measures (e.g. cell protection concept) and each component must be integrated into a state-of-the-art holistic industrial security concept. Third-party products that may be in use should also be considered. You will find more information about industrial security at:

http://www.siemens.com/industrialsecurity

To receive information about product updates on a regular basis, register for our product newsletter. You will find more information at:

http://support.automation.siemens.com

WARNINGDanger as a result of unsafe operating states resulting from software manipulation

Software manipulation (e.g. by viruses, Trojan horses, malware, worms) can cause unsafe operating states to develop in your installation which can result in death, severe injuries and/or material damage.

• Keep the software up to date.

Information and newsletters can be found at:

http://support.automation.siemens.com

• Incorporate the automation and drive components into a holistic, state-of-the-art industrial security concept for the installation or machine.

For more information, visit:

http://www.siemens.com/industrialsecurity

• Make sure that you include all installed products into the holistic industrial security concept.

http://www.siemens.com/industrialsecurityhttp://support.automation.siemens.comhttp://support.automation.siemens.comhttp://www.siemens.com/industrialsecurity

1 Fundamental safety instructions1.2 Industrial security


2


Parameters

Content

2.1 Overview of parameters 12

2.2 List of parameters 24

2.3 Parameters for data sets 336

2.4 BICO parameters (connectors/binectors) 344

2.5 Parameters for write protection and know-how protection 350

2.6 Quick commissioning (p0010 = 1) 352

2 Parameters2.1 Overview of parameters


2.1 Overview of parameters

2.1.1 Explanation of the parameter list

Basic structure of the parameter descriptionsThe data in the following example have been chosen at random. The table below contains all the information that can be included in a parameter description. Some of the information is optional.

The "List of parameters" (Page 24) has the following structure:

- - - - - - - - - - - - Start of example - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Description: TextValue: 0: Name and meaning of value 0

1: Name and meaning of value 12: Name and meaning of value 2etc.

Recommendation: TextIndex: [0] = Name and meaning of index 0

[1] = Name and meaning of index 1[2] = Name and meaning of index 2etc.

Dependency: TextRefer to: pxxxx, rxxxxRefer to: Fxxxxx, Axxxxx

Note: Information that might be useful.

- - - - - - - - - - - - End of example - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The individual pieces of information are described in detail below.

pxxxx[0...n] BICO: Full parameter name / abbreviated nameCU/PM variants Access level: 3 Calculated: p0340 = 1 Data type: FloatingPoint32

Can be changed: C(x), U, T Scaling: p2002 Dyn. index: CDS, p0170Unit group: 6_2 Unit selection: p0505 Func. diagram: 8070Min Max Factory setting0.00 [Nm] 10.00 [Nm] 0.00 [Nm]

Bit field: Bit Signal name 1 signal 0 signal FP00 Name and meaning of bit 0 Yes no 806001 Name and meaning of bit 1 Yes no -02 Name and meaning of bit 2 Yes no 8052

etc.

Danger: Warning: Caution: Safety notices with a warning triangle

Notice: Safety notice without a warning triangle



pxxxx[0...n] Parameter numberThe parameter number is made up of a "p" or "r", followed by the parameter number and the index or bit field (optional).

Examples of the representation in the parameter list:

Other examples of notation in the documentation:

The following applies to adjustable parameters:

The parameter value as delivered is specified under "Factory setting" with the relevant unit in square brackets. The value can be adjusted within the range defined by "Min" and "Max".

The term "linked parameterization" is used in cases where changes to adjustable parameters affect the settings of other parameters.

Linked parameterization can occur, for example, as a result of the following actions and parameters:

• Setting the PROFIBUS telegram (BICO interconnection)

p0922

• Setting component lists

p0230, p0300, p0301, p0400

• Automatically calculating and pre-assigning

p0340, p3900

• Restoring the factory settings

p0970

The following applies to display parameters:

The fields "Min", "Max" and "Factory setting" are specified with a dash "-" and the relevant unit in square parentheses.

• p... Adjustable parameters (read and write)

• r... Display parameters (read only)

• p0918 Adjustable parameter 918

• p2051[0...13] Adjustable parameter 2051, indices 0 to 13

• p1001[0...n] Adjustable parameter 1001, indices 0 to n (n = configurable)

• r0944 Display parameter 944

• r2129.0...15 Display parameter 2129 with bit field from bit 0 (smallest bit) to bit 15 (largest bit)

• p1070[1] Adjustable parameter 1070, index 1

• p2098[1].3 Adjustable parameter 2098, index 1 bit 3

• p0795.4 Adjustable parameter 795, bit 4

Note

The parameter list can contain parameters that are not visible in the expert lists of the particular commissioning software (e.g. parameters for trace functions).



BICO: Full parameter name/Abbreviated nameThe following abbreviations can appear in front of the BICO parameter name:

G120C variantsSpecifies for which G120C variants (communication) the parameter is valid is. If no G120C variant is listed, then the parameter is valid for all variants.

The following information relating to "G120C variants" can be displayed under theparameter number:

• BI: Binector Input This parameter is used for selecting the source of a digital signal.

• BO: Binector Output This parameter is available as a digital signal for interconnection with other parameters.

• CI: Connector Input This parameter is used for selecting the source of an "analog" signal.

• CO: Connector Output This parameter is available as an "analog" signal for interconnection with other parameters.

• CO/BO: Connector/Binector Output This parameter is available as an "analog" and digital signal for interconnection with other parameters.

Note

A BICO input (BI/CI) cannot be interconnected with just any BICO output (BO/CO, signal source).When interconnecting a BICO input using the commissioning software, only the corresponding possible signal sources are listed.

Function diagrams 1020 ... 1030 explain the symbols for BICO parameters and how to deal with BICO technology.

Table 2-1 Information in the "CU/PM variants" field

CU/PM variants Meaning

All G120C variants have this parameter.

G120C_CAN G120C with CAN interface

G120C_DP G120C with PROFIBUS interface

G120C_PN G120C with PROFINET interface

G120C_USS G120C with USS interface



Access levelSpecifies the minimum access level required to be able to display and change the relevant parameter. The required access level can be set using p0003.

The system uses the following access levels:

• 1: Standard (not adjustable, included in p0003 = 3)

• 2: Extended (not adjustable, included in p0003 = 3)

• 3: Expert

• 4: Service

Parameters with this access level are password protected.

CalculatedSpecifies whether the parameter is influenced by automatic calculations.

p0340 determines which calculations are to be performed:

• p0340 = 1 includes the calculations from p0340 = 2, 3, 4, 5.

• p0340 = 2 calculates the motor parameters (p0350 ... p0360, p0625).

• p0340 = 3 includes the calculations from p0340 = 4, 5.

• p0340 = 4 only calculates the controller parameters.

• p0340 = 5 only calculates the controller limits.

Parameters with a reference to p0340 after "Calculated" depend on the Power Module being used and the motor. In this case, the values at "Factory setting" do not correspond to the actual values because these values are calculated during the commissioning. This also applies to the motor parameters.

Note

Parameter p0003 is CU-specific (belongs to the Control Unit).

A higher access level will also include the functions of the lower levels.

Note

For p3900 > 0, p0340 = 1 is also called automatically.

After p1900 = 1, 2, p0340 = 3 is also called automatically.



Data typeThe information on the data type can consist of the following two items (separated by a slash):

• First item

Data type of the parameter.

• Second item (for binector or connector input only)

Data type of the signal source to be interconnected (binector-/connector output).

Parameters can have the following data types:

Depending on the data type of the BICO input parameter (signal sink) and BICO output parameter (signal source), the following combinations are possible when creating BICO interconnections:

• Integer8 I8 8-bit integer number



• Unsigned8 U8 8 bits without sign



• FloatingPoint32 Float 32-bit floating point number

Table 2-2 Possible combinations of BICO interconnections

BICO input parameter

CI parameter BI parameter

BICO output parameter Unsigned32 / Integer16

Unsigned32 / Integer32

Unsigned32 / FloatingPoint32

Unsigned32 / Binary

CO: Unsigned8 x x – –



CO: Integer16 x x r2050 –

CO: Integer32 x x r2060 –

CO: FloatingPoint32 x x x –

BO: Unsigned8 – – – x



BO: Integer16 – – – x

BO: Integer32 – – – x

BO: FloatingPoint32 – – – –

Legend: x :–:

rxxxx:

BICO interconnection permittedBICO interconnection not permittedBICO interconnection is only permitted for the specified CO parameters



Can be changedThe "-" sign indicates that the parameter can be changed in any object state and that the change will be effective immediately.

The information "C(x), T, U" ((x): optional) means that the parameter can be changed only in the specified drive unit state and that the change will not take effect until the unit switches to another state. This can be a single state or multiple states.

The following states are available:

ScalingSpecification of the reference variable with which a signal value is automatically converted for a BICO interconnection.

The following reference variables are available:

• p2000 … p2007: Reference speed, reference voltage, etc.

• PERCENT: 1.0 = 100 %

• 4000H: 4000 hex = 100 % (wort) or 4000 0000 hex = 100 % (double word)

• p0514: specific normalization

Refer to the description for p0514[0…9] and p0515[0…19] to p0524[0…19]

• C(x) commissioning C: Commissioning

Drive commissioning is in progress (p0010 > 0).

Pulses cannot be enabled.

The parameter can only be changed in the following drive commissioning settings (p0010 > 0):

• C: Can be changed for all settings p0010 > 0.

• C(x): Can only be changed for the settings p0010 = x.

A modified parameter value does not take effect until drive commissioning mode is exited with p0010 = 0.

• U Operation U: Run

Pulses are enabled.

• T Ready T: Ready to run

The pulses are not enabled and the status "C(x)" is not active.



Dyn. index (dynamic index)For parameters with a dynamic index [0...n], the following information is specified here:

• Data set (if available).

• Parameter for the number of indices (n = number - 1).

The following information can be contained in this field:

• "CDS, p0170" (Command Data Set, CDS count)

Example:

p1070[0] main setpoint [command data set 0]

p1070[1] main setpoint [command data set 1], etc.

• "DDS, p0180" (Drive Data Set, DDS count)

• "EDS, p0140" (Encoder Data Set, EDS count)

• "MDS, p0130" (Motor Data Set, MDS count)

• "PDS, p0120" (Power unit Data Set, PDS count)

Data sets can only be created and deleted when p0010 = 15.

Unit group and unit selectionThe standard unit of a parameter is specified in square brackets after the values for "Min", "Max", and "Factory setting".

For parameters where the unit can be switched over, the specifications for "Unit group" and "Unit selection" determine the group to which this parameter belongs and with which parameter the unit can be changed over.

Example:

Unit group: 7_1, unit selection: p0505

The parameter belongs to unit group 7_1 and the unit can be changed over using p0505.

All the potential unit groups and possible unit selections are listed below.

Note

Information on the data sets can be taken from the following references:

Operating Instructions SINAMICS G120 Frequency Converter G120C.

Table 2-3 Unit group (p0100)

Unit group Unit selection for p0100 = Reference variable for %

0 1 2

7_4 Nm lbf ft Nm -

14_6 kW hp kW -

25_1 kg m2 lb ft2 kg m2 -

27_1 kg lb kg -

28_1 Nm/A lbf ft/A Nm/A -



Function diagramThe parameter is included in this function diagram. The structure of the parameter function and its relationship with other parameters is shown in the specified function diagram.



1 2 3 4

2_1 Hz % Hz % p2000

3_1 1 rpm % 1 rpm % p2000

5_1 Vrms % Vrms % p2001

5_2 V % V % p2001

5_3 V % V % p2001

6_2 Arms % Arms % p2002

6_5 A % A % p2002

7_1 Nm % lbf ft % p2003

7_2 Nm Nm lbf ft lbf ft -

14_5 kW % hp % r2004

14_10 kW kW hp hp -

21_1 °C °C °F °F -

21_2 K K °F °F -

39_1 1/s2 % 1/s2 % p2007



Value Unit

9_1 The values that can be set and the technological units are shown in p0595.



Parameter values

DescriptionExplanation of the function of a parameter

ValuesLists the possible values of a parameter.

RecommendationInformation about recommended settings.

IndexThe name and meaning of each individual index is specified for indexed parameters.

The following applies to the values (Min, Max, Factory setting) of indexed adjustable parameters:

• Min, Max:

The adjustment range and unit apply to all indices.

• Factory setting:

When all indices have the same factory setting, index 0 is specified with the unit to represent all indices.

When the indices have different factory settings, they are all listed individually with the unit.

Min. Minimum value of the parameter [unit]

Max Maximum value of the parameter [unit]

Factory setting Value when delivered [unit]

In the case of a binector/connector input, the signal source of the default BICO interconnection is specified. A non-indexed connector output is assigned the index [0].

A different value may be displayed for certain parameters (e.g. p1800) at the initial commissioning stage or when establishing the factory settings.Reason:The setting of these parameters is determined by the operating environment of the Control Unit (e.g. depending on converter type, power unit).



Bit fieldFor parameters with bit fields, the following information is provided about each bit:

• Bit number and signal name

• Meaning for signal states 0 and 1

• Function diagram (FP) (optional).

The signal is shown on this function diagram.

DependencyConditions that must be fulfilled in conjunction with this parameter. Also includes special effects that can occur between this parameter and others.

Where necessary, "Refer to:" indicates the following information:

• List of other relevant parameters to be considered.

• List of faults and alarms to be considered.

Safety guidelinesImportant information that must be observed to avoid the risk of physical injury or material damage.

Information that must be observed to avoid any problems.

Information that the user may find useful.

Danger The description of this safety notice can be found at the beginning of this manual (see "Legal information" (Page 4)).

Warning The description of this safety notice can be found at the beginning of this manual (see "Legal information" (Page 4)).

Caution The description of this safety notice can be found at the beginning of this manual (see "Legal information" (Page 4)).

Notice The description of this safety notice can be found at the beginning of this manual (see "Legal information" (Page 4)).

Note Information that the user may find useful.



2.1.2 Number ranges of parameters

Faults and alarms are organized into the following number ranges:

Note

The following number ranges represent an overview for all the parameters available for the SINAMICS drive family.

The parameters for the product described in this List Manual are described in detail in "List of parameters" (Page 24).

Table 2-6 Number ranges of faults and alarms

of To Area

1000 3999 Control Unit

4000 4999 Reserved

5000 5999 Power section

6000 6899 Infeed

6900 6999 Braking Module

7000 7999 Drive

8000 8999 Option Board

9000 12999 Reserved

13000 13020 Licensing

13021 13099 Reserved

13100 13102 Know-how protection


20000 29999 OEM

30000 30999 DRIVE-CLiQ component power unit

31000 31999 DRIVE-CLiQ component encoder 1


NoteFaults that occur are automatically output as an alarm if the encoder is parameterized as a direct measuring system and does not intervene in the motor control.


NoteFaults that occur are automatically output as an alarm if the encoder is parameterized as a direct measuring system and does not intervene in the motor control.

34000 34999 Voltage Sensing Module (VSM)

35000 35199 Terminal Module 54F (TM54F)

35200 35999 Terminal Module 31 (TM31)

36000 36999 DRIVE-CLiQ Hub Module

37000 37999 HF Damping Module



40000 40999 Controller Extension 32 (CX32)


49000 49999 SINAMICS GM/SM/GL

50000 50499 Communication Board (COMM BOARD)

50500 59999 OEM Siemens

60000 65535 SINAMICS DC MASTER (closed-loop DC current control)

Table 2-6 Number ranges of faults and alarms, continued

of To Area

2 Parameters2.2 List of parameters


2.2 List of parametersProduct: SINAMICS G120C, Version: 4705500, Language: engObjects: G120C_CAN, G120C_DP, G120C_PN, G120C_USS

Description: Operating display for the drive.Value: 0: Operation - everything enabled

10: Operation - set "enable setpoint" = "1"12: Operation - RFG frozen, set "RFG start" = "1"13: Operation - set "enable RFG" = "1"14: Operation - MotID, excit. running15: Operation - open brake (p1215)16: Operation - withdraw braking with OFF1 using "ON/OFF1" = "1"17: Operation - braking with OFF3 can only be interrupted with OFF218: Operation - brake on fault, remove fault, acknowledge19: Operation - DC braking active (p1230, p1231)21: Ready for operation - set "Operation enable" = "1" (p0852)22: Ready for operation - de-magnetizing running (p0347)31: Ready for switching on - set "ON/OFF1" = "0/1" (p0840)35: Switching on inhibited - carry out first commissioning (p0010)41: Switching on inhibited - set "ON/OFF1" = "0" (p0840)42: Switching on inhibited - set "OC/OFF2" = "1" (p0844, p0845)43: Switching on inhibited - set "OC/OFF3" = "1" (p0848, p0849)44: Switching on inhibited - supply STO terminal w/ 24 V (hardware)45: Switching on inhibited - rectify fault, acknowledge fault, STO46: Switching on inhibited - exit comm mode (p0010)70: Initialization200: Wait for booting/partial booting

Dependency: Refer to: r0046Notice: For several missing enable signals, the corresponding value with the highest number is displayed.Note: OC: Operating condition

RFG: Ramp-function generatorCOMM: CommissioningMotID: Motor data identification

Description: Sets the access level to read and write parameters.Value: 3: Expert

4: ServiceNote: A higher set access level also includes the lower one.

Access level 3 (experts):Expert know-how is required for these parameters (e.g. BICO parameterization).Access level 4 (service):For these parameters, it is necessary that authorized service personnel enter the appropriate password (p3950).

r0002 Drive operating display / Drv op_displayAccess level: 2 Calculated: - Data type: Integer16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 200 -

p0003 Access level / Acc_levelAccess level: 1 Calculated: - Data type: Integer16Can be changed: C, U, T Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 3 4 3



Description: Sets the parameter filter to commission a drive.Setting this parameter filters out the parameters that can be written into in the various commissioning steps.

Value: 0: Ready1: Quick commissioning2: Power unit commissioning3: Motor commissioning5: Technological application/units15: Data sets29: Only Siemens int30: Parameter reset39: Only Siemens int49: Only Siemens int95: Safety Integrated commissioning

Dependency: Refer to: r3996Notice: When the parameter is reset to a value of 0, short-term communication interruptions may occur.Note: The drive can only be powered up outside the drive commissioning (inverter enable). To realize this, this parameter

must be set to 0.By setting p3900 to a value other than 0, the quick commissioning is completed, and this parameter is automatically reset to 0.Procedure for "Reset parameter": Set p0010 to 30 and p0970 to 1.Once the Control Unit has been booted up for the first time, the motor parameters suitable for the power unit have been defined, and the control parameters have been calculated accordingly, p0010 is automatically reset to 0.p0010 = 3 is used for the subsequent commissioning of additional drive data sets (creating data sets: see p0010 = 15).p0010 = 29, 39, 49: Only for internal Siemens use!

Description: Runs the corresponding macro files.Notice: After the value has been modified, no further parameter modifications can be made and the status is shown in r3996.

Modifications can be made again when r3996 = 0.When executing a specific macro, the corresponding programmed settings are made and become active.

Note: Macros available as standard are described in the technical documentation of the particular product.

Description: Runs the corresponding macro files.Notice: After the value has been modified, no further parameter modifications can be made and the status is shown in r3996.

Modifications can be made again when r3996 = 0.When executing a specific macro, the corresponding programmed settings are made and become active.

Note: Macros available as standard are described in the technical documentation of the particular product.

p0010 Drive commissioning parameter filter / Drv comm. par_filtAccess level: 1 Calculated: - Data type: Integer16Can be changed: C(1), T Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 2800, 2818Min Max Factory setting 0 95 1

p0015 Macro drive unit / Macro drv unitG120C_CANG120C_USS

Access level: 1 Calculated: - Data type: Unsigned32Can be changed: C, C(1) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 999999 12

p0015 Macro drive unit / Macro drv unitG120C_DPG120C_PN

Access level: 1 Calculated: - Data type: Unsigned32Can be changed: C, C(1) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 999999 7



Description: Displays the firmware version of the Control Unit.Dependency: Refer to: r0197, r0198Note: Example:

The value 1010100 should be interpreted as V01.01.01.00.

Description: Displays the currently smoothed speed setpoint at the input of the speed controller or U/f characteristic (after the interpolator).

Dependency: Refer to: r0060Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The speed setpoint is available smoothed (r0020) and unsmoothed (r0060).

Description: Display of the calculated and smoothed rotor speed.Frequency components from the slip compensation (for induction motors) are not included.

Dependency: Refer to: r0022, r0063Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The speed actual value is available smoothed (r0021, r0022) and unsmoothed (r0063).

Description: Display of the calculated and smoothed rotor speed.Frequency components from the slip compensation (for induction motors) are not included.r0022 is identical to r0021, however, it always has units of rpm and contrary to r0021 cannot be changed over.

Dependency: Refer to: r0021, r0063Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The speed actual value is available smoothed (r0021, r0022) and unsmoothed (r0063).

r0018 Control Unit firmware version / CU FW versionAccess level: 3 Calculated: - Data type: Unsigned32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 4294967295 -

r0020 Speed setpoint smoothed / n_set smthAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 5020, 6799Min Max Factory setting - [rpm] - [rpm] - [rpm]

r0021 CO: Actual speed smoothed / n_act smoothAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 6799Min Max Factory setting - [rpm] - [rpm] - [rpm]

r0022 Speed actual value rpm smoothed / n_act rpm smoothAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6799Min Max Factory setting - [rpm] - [rpm] - [rpm]



Description: Display of the smoothed output frequency.Frequency components from the slip compensation (for induction motors) are included.

Dependency: Refer to: r0066Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The output frequency is available smoothed (r0024) and unsmoothed (r0066).

Description: Displays the smoothed output voltage of the power unit.Dependency: Refer to: r0072Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The output voltage is available smoothed (r0025) and unsmoothed (r0072).

Description: Displays the smoothed actual value of the DC link voltage.Dependency: Refer to: r0070Notice: When measuring a DC link voltage < 200 V, for the Power Module a valid measured value is not supplied. In this

case, when an external 24 V power supply is connected, a value of approx. 24 V is displayed in the display parameter.

Note: Smoothing time constant = 100 msThe signal is not suitable as a process quantity and may only be used as a display quantity.The DC link voltage is available smoothed (r0026) and unsmoothed (r0070).r0026 sets itself to the lower value of the pulsating DC link voltage.

Description: Displays the smoothed absolute actual current value.Dependency: Refer to: r0068Notice: This smoothed signal is not suitable for diagnostics or evaluation of dynamic operations. In this case, the

unsmoothed value should be used.

r0024 Output frequency smoothed / f_outp smoothAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6300, 6799Min Max Factory setting - [Hz] - [Hz] - [Hz]

r0025 CO: Output voltage smoothed / U_outp smoothAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 5730, 6300, 6799Min Max Factory setting - [Vrms] - [Vrms] - [Vrms]

r0026 CO: DC link voltage smoothed / Vdc smoothAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6799Min Max Factory setting - [V] - [V] - [V]

r0027 CO: Absolute actual current smoothed / I_act abs val smthAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 5730, 6799, 8850,

8950Min Max Factory setting - [Arms] - [Arms] - [Arms]



Note: Smoothing time constant = 300 msThe signal is not suitable as a process quantity and may only be used as a display quantity.The absolute current actual value is available smoothed (r0027) and unsmoothed (r0068).

Description: Displays the smoothed actual value of the modulation depth.Dependency: Refer to: r0074Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The modulation depth is available smoothed (r0028) and unsmoothed (r0074).

Description: Displays the smoothed field-generating actual current.Dependency: Refer to: r0076Note: Smoothing time constant = 300 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The field-generating current actual value is available smoothed (r0029) and unsmoothed (r0076).

Description: Displays the smoothed torque-generating actual current.Dependency: Refer to: r0078Note: Smoothing time constant = 300 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The torque-generating current actual value is available smoothed (r0030) and unsmoothed (r0078).

Description: Displays the smoothed torque actual value.Dependency: Refer to: r0080Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The torque actual value is available smoothed (r0031) and unsmoothed (r0080).

r0028 Modulation depth smoothed / Mod_depth smthAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 5730, 6799, 8950Min Max Factory setting - [%] - [%] - [%]

r0029 Current actual value field-generating smoothed / Id_act smoothAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6799Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0030 Current actual value torque-generating smoothed / Iq_act smoothAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6799Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0031 Actual torque smoothed / M_act smoothAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2003 Dyn. index: -Unit group: 7_1 Unit selection: p0505 Func. diagram: 5730, 6799Min Max Factory setting - [Nm] - [Nm] - [Nm]



Description: Displays the smoothed actual value of the active power.Dependency: Refer to: r0082Notice: This smoothed signal is not suitable for diagnostics or evaluation of dynamic operations. In this case, the

unsmoothed value should be used.Note: Power delivered at the motor shaft.

The active power is available smoothed (r0032 with 100 ms) and unsmoothed (r0082).

Description: Displays the smoothed torque utilization as a percentage.Dependency: This parameter is only available for vector control. For U/f control r0033 = 0 %.Note: Smoothing time constant = 100 ms

The signal is not suitable as a process quantity and may only be used as a display quantity.The torque utilization is available smoothed (r0033) and unsmoothed (r0081).For M_set total (r0079) > 0, the following applies:- Required torque = M_set total- Actual torque limit = M_max upper effective (r1538)For M_set total (r0079)



Note: Smoothing time constant = 100 msThe signal is not suitable as a process quantity and may only be used as a display quantity.For r0034 = -200.0 %, the following applies:The value is invalid (e.g. the motor temperature model is not activated or has been incorrectly parameterized).

Description: Display and connector output for the actual temperature in the motor.Note: For r0035 not equal to -200.0 °C, the following applies:

- this temperature display is valid.- a KTY sensor is connected.- the thermal model for the induction motor is activated (p0612 bit 1 = 1 and temperature sensor de-activated: p0600 = 0 or p0601 = 0).For r0035 equal to -200.0 °C, the following applies:- this temperature display is not valid (temperature sensor error).- A PTC sensor or bimetallic NC contact is connected.- the temperature sensor of the synchronous motor is de-activated (p0600 = 0 or p0601 = 0).

Description: Displays the power unit overload determined using the I2t calculation.A current reference value is defined for the I2t monitoring of the power unit. It represents the current that can be conducted by the power unit without any influence of the switching losses (e.g. the continuously permissible current of the capacitors, inductances, busbars, etc.).If the I2t reference current of the power unit is not exceeded, then an overload (0 %) is not displayed.In the other case, the degree of thermal overload is calculated, whereby 100% results in a trip.

Dependency: Refer to: p0290Refer to: F30005

Description: Display and connector output for the temperature in the power unit.

r0035 CO: Motor temperature / Mot tempAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2006 Dyn. index: -Unit group: 21_1 Unit selection: p0505 Func. diagram: 8016, 8017Min Max Factory setting - [°C] - [°C] - [°C]

r0036 CO: Power unit overload I2t / PU overload I2tAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8019Min Max Factory setting - [%] - [%] - [%]

r0037[0...19] CO: Power unit temperatures / PU temperaturesAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2006 Dyn. index: -Unit group: 21_1 Unit selection: p0505 Func. diagram: 8019Min Max Factory setting - [°C] - [°C] - [°C]



Index: [0] = Inverter maximum value[1] = Depletion layer maximum value[2] = Rectifier maximum value[3] = Air intake[4] = Interior of power unit[5] = Inverter 1[6] = Inverter 2[7...10] = Reserved[11] = Rectifier 1[12] = Reserved[13] = Depletion layer 1[14] = Depletion layer 2[15] = Depletion layer 3[16] = Depletion layer 4[17] = Depletion layer 5[18] = Depletion layer 6[19] = Reserved

Notice: Only for internal Siemens troubleshooting.Note: The value of -200 indicates that there is no measuring signal.

r0037[0]: Maximum value of the inverter temperatures (r0037[5...10]).r0037[1]: Maximum value of the depletion layer temperatures (r0037[13...18]).r0037[2]: Maximum value of the rectifier temperatures (r0037[11...12]).The maximum value is the temperature of the hottest inverter, depletion layer, or rectifier.r0037[2, 3, 6, 11, 14...18] is only relevant for chassis power units.In the case of a fault, the particular shutdown threshold depends on the power unit, and cannot be read out.

Description: Displays the smoothed actual power factor. This refers to the electrical power of the basic fundamental signals at the converter output terminals.

Notice: For infeed units, the following applies:For active powers < 25 % of the rated power, this does not provide any useful information.

Note: Smoothing time constant = 300 msThe signal is not suitable as a process quantity and may only be used as a display quantity.

Description: Displays the energy values at the output terminals of the power unit.Index: [0] = Energy balance (sum)

[1] = Energy drawn[2] = Energy fed back

Dependency: Refer to: p0040Note: Re index 0:

Difference between the energy drawn and energy that is fed back.

r0038 Power factor smoothed / Cos phi smoothAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6799, 8850, 8950Min Max Factory setting - - -

r0039[0...2] CO: Energy display / Energy displAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - [kWh] - [kWh] - [kWh]



Description: Setting to reset the display in r0039 and r0041.Procedure:Set p0040 = 0 --> 1The displays are reset and the parameter is automatically set to zero.

Dependency: Refer to: r0039Note: When the energy usage display is reset, the process energy display r0042 is also reset.

Description: Displays the saved energy referred to 100 operating hours.Dependency: Refer to: p0040Note: This display is used for a fluid-flow machine.

The flow characteristic is entered into p3320 ... p3329.For an operating time of below 100 hours, the display is interpolated up to 100 hours.

Description: Displays the energy values at the output terminals of the power unit.Index: [0] = Energy balance (sum)

[1] = Energy drawn[2] = Energy fed back

Dependency: Refer to: p0043Note: The signal can be displayed as process variable (scaling: 1 = 1 Wh).

This is enabled in p0043. The display is also reset with p0040 = 1.If an enable is present in r0043 when the Control Unit powers up, then the value from r0039 is transferred into r0042.As r0039 serves as a reference signal for r0042, due to format reasons, the process energy display can only process values of r0039 up to 2147483 kWh. Further, r0039 should also be reset.

Description: Setting to enable and reset the process energy display in r0042.The energy display starts when a one is connected to the Bico input.

Dependency: Refer to: r0042

p0040 Reset energy consumption display / Energy usage resetAccess level: 3 Calculated: - Data type: Unsigned8Can be changed: U, T Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 1 0

r0041 Energy consumption saved / Energy cons savedAccess level: 2 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - [kWh] - [kWh] - [kWh]

r0042[0...2] CO: Process energy display / Process energyAccess level: 2 Calculated: - Data type: Integer32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - [Wh] - [Wh] - [Wh]

p0043 BI: Enable energy usage display / Enab energy usageAccess level: 2 Calculated: - Data type: U32 / BinaryCan be changed: U, T Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - 0



Description: Sets the smoothing time constant for the following display values:r0063[1], r0068[1], r0080[1], r0082[1].

Description: Display and BICO output for missing enable signals that are preventing the closed-loop drive control from being commissioned.

Dependency: Refer to: r0002Note: The value r0046 = 0 indicates that all enable signals for this drive are present.

Bit 00 = 1 (enable signal missing), if:- the signal source in p0840 is a 0 signal.- there is a "switching on inhibited".Bit 01 = 1 (enable signal missing), if:- the signal source in p0844 or p0845 is a 0 signal.Bit 02 = 1 (enable signal missing), if:- the signal source in p0848 or p0849 is a 0 signal.Bit 03 = 1 (enable signal missing), if:- the signal source in p0852 is a 0 signal.Bit 04 =1 (DC brake active) when:- the signal source in p1230 has a 1 signal.Bit 08 = 1 (enable signal missing), if:- safety functions have been enabled and STO is active.- STO is selected via onboard terminals or PROFIsafe.- a safety-relevant signal is present with STOP A response.- the "STO via terminals at the Power Module" function is selected.

p0045 Display values smoothing time constant / Disp_val T_smoothAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: U, T Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6714, 8012Min Max Factory setting 0.00 [ms] 10000.00 [ms] 4.00 [ms]

r0046.0...31 CO/BO: Missing enable sig / Missing enable sigAccess level: 1 Calculated: - Data type: Unsigned32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 2634Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 OFF1 enable missing Yes No 795401 OFF2 enable missing Yes No -02 OFF3 enable missing Yes No -03 Operation enable missing Yes No -04 DC braking enable missing Yes No -08 Safety enable missing Yes No -10 Ramp-function generator enable missing Yes No -11 Ramp-function generator start missing Yes No -12 Setpoint enable missing Yes No -16 OFF1 enable internal missing Yes No -17 OFF2 enable internal missing Yes No -18 OFF3 enable internal missing Yes No -19 Pulse enable internal missing Yes No -20 DC braking internal enable missing Yes No -21 Power unit enable missing Yes No -26 Drive inactive or not operational Yes No -27 De-magnetizing not completed Yes No -28 Brake open missing Yes No -30 Speed controller inhibited Yes No -31 Jog setpoint active Yes No -



Bit 10 = 1 (enable signal missing), if:- the signal source in p1140 is a 0 signal.Bit 11 = 1 (enable signal missing) if the speed setpoint is frozen, because:- the signal source in p1141 is a 0 signal.- the speed setpoint is entered from jogging and the two signal sources for jogging, bit 0 (p1055) and bit 1 (p1056) have a 1 signal.Bit 12 = 1 (enable signal missing), if:- the signal source in p1142 is a 0 signal.Bit 16 = 1 (enable signal missing), if:- there is an OFF1 fault response. The system is only enabled if the fault is removed and was acknowledged and the "switching on inhibited" withdrawn with OFF1 = 0.Bit 17 = 1 (enable signal missing), if:- commissioning mode is selected (p0010 > 0).- there is an OFF2 fault response.- the drive is not operational.Bit 18 = 1 (enable signal missing), if:- OFF3 has still not been completed or an OFF3 fault response is present.Bit 19 = 1 (internal pulse enable missing), if:- sequence control does not have a finished message.Bit 20 = 1 (internal DC brake active), if:- the drive is not in the state "Operation" or in "OFF1/3".- the internal pulse enable is missing (r0046.19 = 0).Bit 21 = 1 (enable signal missing), if:- the power unit does not issue an enable signal (e.g. because DC link voltage is too low).- the holding brake opening time (p1216) has still not expired.- The hibernation mode is active.Bit 26 = 1 (enable signal missing), if:- the drive is not operational.Bit 27 = 1 (enable signal missing), if:- de-magnetization not completed.Bit 28 = 1 (enable signal missing), if:- the holding brake is closed or has still not been opened.Bit 30 = 1 (speed controller inhibited), if one of the following reasons is present:- the pole position identification is active.- motor data identification is active (only certain steps).Bit 31 = 1 (enable signal missing), if:- the speed setpoint from jog 1 or 2 is entered.

Description: Displays the actual status for the motor data identification (stationary measurement) and the speed controller optimization (rotating measurement).

Value: 0: No measurement115: Measurement q leakage inductance (part 2)120: Speed controller optimization (vibration test)140: Calculate speed controller setting150: Measurement moment of inertia170: Measurement magnetizing current and saturation characteristic195: Measurement q leakage inductance (part 1)200: Rotating measurement selected220: identification leakage inductance

r0047 Motor data identification and speed controller optimization / MotID and n_optAccess level: 1 Calculated: - Data type: Integer16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 300 -



230: Identification rotor time constant240: Identification stator inductance250: Identification stator inductance LQLD260: Identification circuit270: Identification stator resistance290: Identification valve lockout time300: Stationary measurement selected

Description: Displays the effective Command Data Set (CDS).

Dependency: Refer to: p0810, r0836Note: The Command Data Set selected using a binector input (e.g. p0810) is displayed using r0836.

Description: Displays the effective Drive Data Set (DDS).

Dependency: Refer to: p0820, r0837Note: When selecting the motor data identification routine and the rotating measurement, the drive data set changeover is

suppressed.

Description: Display and connector output for status word 1.

r0050.0...1 CO/BO: Command Data Set CDS effective / CDS effectiveAccess level: 3 Calculated: - Data type: Unsigned8Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8560Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 CDS eff bit 0 ON OFF -01 CDS eff bit 1 ON OFF -

r0051.0 CO/BO: Drive Data Set DDS effective / DDS effectiveAccess level: 3 Calculated: - Data type: Unsigned8Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8565Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 DDS eff bit 0 ON OFF -

r0052.0...15 CO/BO: Status word 1 / ZSW 1Access level: 2 Calculated: - Data type: Unsigned16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 Rdy for switch on Yes No -01 Ready Yes No -02 Operation enabled Yes No -03 Fault present Yes No -04 Coast down active (OFF2) No Yes -05 Quick Stop active (OFF3) No Yes -06 Switching on inhibited active Yes No -07 Alarm present Yes No -08 Deviation setpoint/actual speed No Yes -09 Control request Yes No -10 Maximum speed reached Yes No -11 I, M, P limit reached No Yes -12 Motor holding brake open Yes No -



Note: Re bit 03:This signal is inverted if it is interconnected to a digital output.Re r0052:The status bits have the following sources:Bit 00: r0899 Bit 0Bit 01: r0899 Bit 1Bit 02: r0899 Bit 2Bit 03: r2139 Bit 3 (or r1214.10 for p1210 > 0)Bit 04: r0899 Bit 4Bit 05: r0899 Bit 5Bit 06: r0899 Bit 6Bit 07: r2139 Bit 7Bit 08: r2197 Bit 7Bit 09: r0899 Bit 7Bit 10: r2197 Bit 6Bit 11: r0056 Bit 13 (negated)Bit 12: r0899 Bit 12Bit 13: r2135 Bit 12 (negated)Bit 14: r2197 Bit 3Bit 15: r2135 Bit 15 (negated)

Description: Display and BICO output for status word 2.

Notice: p2081 is used to define the signal sources of the PROFIdrive status word interconnection.Note: The following status bits are displayed in r0053:

Bit 00: r1239 Bit 8Bit 02: r2197 Bit 0 (negated)Bit 06: r2197 Bit 4Bit 10: r2349 Bit 10Bit 11: r2349 Bit 11

13 Alarm motor overtemperature No Yes -14 Motor rotates forwards Yes No -15 Alarm drive converter overload No Yes -

r0053.0...11 CO/BO: Status word 2 / ZSW 2Access level: 2 Calculated: - Data type: Unsigned16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 DC braking active Yes No -01 |n_act| > p1226 (n_standstill) Yes No -02 |n_act| > p1080 (n_min) Yes No -03 I_act >= p2170 Yes No -04 |n_act| > p2155 Yes No -05 |n_act| = r1119 (n_set) Yes No -07 Vdc p2172 Yes No -09 Reserved Yes No -10 Technology controller output at the lower

limitYes No -

11 Technology controller output at the upper limit

Yes No -



Description: Displays control word 1.

Note: The following control bits are displayed in r0054:Bit 00: r0898 Bit 0Bit 01: r0898 Bit 1Bit 02: r0898 Bit 2Bit 03: r0898 Bit 3Bit 04: r0898 Bit 4Bit 05: r0898 Bit 5Bit 06: r0898 Bit 6Bit 07: r2138 Bit 7Bit 08: r0898 Bit 8Bit 09: r0898 Bit 9Bit 10: r0898 Bit 10Bit 11: r1198 Bit 11Bit 13: r1198 Bit 13Bit 14: r1198 Bit 14Bit 15: r0836 Bit 0

Description: Display and BICO output for supplementary control word.

r0054.0...15 CO/BO: Control word 1 / STW 1Access level: 2 Calculated: - Data type: Unsigned16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 ON/OFF1 Yes No -01 OC / OFF2 No Yes -02 OC / OFF3 No Yes -03 Operation enable Yes No -04 Ramp-function generator enable Yes No -05 Continue ramp-function generator Yes No -06 Speed setpoint enable Yes No -07 Acknowledge fault Yes No -08 Jog bit 0 Yes No 303009 Jog bit 1 Yes No 303010 Master control by PLC Yes No -11 Direction reversal (setpoint) Yes No -13 Motorized potentiometer raise Yes No -14 Motorized potentiometer lower Yes No -15 CDS bit 0 Yes No -

r0055.0...15 CO/BO: Supplementary control word / Suppl STWAccess level: 3 Calculated: - Data type: Unsigned16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 2513Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 Fixed setp bit 0 Yes No -01 Fixed setp bit 1 Yes No -02 Fixed setp bit 2 Yes No -03 Fixed setp bit 3 Yes No -04 DDS select. bit 0 Yes No -05 Reserved Yes No -08 Technology controller enable Yes No -09 DC braking enable Yes No -11 Reserved Yes No -



Note: CDS: Command Data SetThe following control bits are displayed in r0055:Bit 00: r1198.0Bit 01: r1198.1Bit 02: r1198.2Bit 03: r1198.3Bit 04: r0837.0Bit 08: r2349.0 (negated)Bit 09: r1239.11Bit 13: r2138.13 (negated)Bit 15: r0836.1

Description: Display and BICO output for the status word of the closed-loop control.

Description: Displays the actual speed setpoint at the input of the speed controller or U/f characteristic (after the interpolator).Dependency: Refer to: r0020Note: The speed setpoint is available smoothed (r0020) and unsmoothed (r0060).

12 Reserved Yes No -13 External fault 1 (F07860) No Yes -15 CDS bit 1 Yes No -

r0056.0...15 CO/BO: Status word, closed-loop control / ZSW cl-loop ctrlAccess level: 3 Calculated: - Data type: Unsigned16Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 2526Min Max Factory setting - - -

Bit field: Bit Signal name 1 signal 0 signal FP00 Initialization completed Yes No -01 De-magnetizing completed Yes No -02 Pulse enable available Yes No -03 Soft starting present Yes No -04 Magnetizing completed Yes No -05 Voltage boost when starting Active Inactive 630106 Acceleration voltage Active Inactive 630107 Frequency negative Yes No -08 Field weakening active Yes No -09 Voltage limit active Yes No 671410 Slip limit active Yes No 631011 Frequency limit active Yes No -12 Current limiting controller voltage output

activeYes No -

13 Current/torque limiting Active Inactive 606014 Vdc_max controller active Yes No 6220,

632015 Vdc_min controller active Yes No 6220,

6320

r0060 CO: Speed setpoint before the setpoint filter / n_set before filt.Access level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 2701, 6030, 6799Min Max Factory setting - [rpm] - [rpm] - [rpm]



Description: Display and connector output for the speed setpoint after the setpoint filters.

Description: Displays the speed actual value.Frequency components from the slip compensation (for induction motors) are not included.

Index: [0] = Unsmoothed[1] = Smoothed with p0045[2] = Calculated from f_set - f_slip (unsmoothed)

Dependency: Refer to: r0021, r0022Note: The speed actual value r0063[0] – smoothed with p0045 – is additionally displayed in r0063[1]. r0063[1] can be used

as process variable for the appropriate smoothing time constant p0045.The speed (r0063[2]) calculated from the output frequency and slip can only be compared with the speed actual value (r0063[0]) in the steady-state.For U/f control, the mechanical speed calculated from the output frequency and the slip is shown in r0063[2] even if slip compensation is deactivated.

Description: Displays the actual system deviation of the speed controller.

Description: Displays the slip frequency for induction motors (ASM).

Description: Display and connector output for the unsmoothed output frequency of the power unit.Frequency components from the slip compensation (induction motor) are included.

r0062 CO: Speed setpoint after the filter / n_set after filterAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 6020, 6030, 6031Min Max Factory setting - [rpm] - [rpm] - [rpm]

r0063[0...2] CO: Speed actual value / n_actAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 6020, 6799Min Max Factory setting - [rpm] - [rpm] - [rpm]

r0064 CO: Speed controller system deviation / n_ctrl system devAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 3_1 Unit selection: p0505 Func. diagram: 6040Min Max Factory setting - [rpm] - [rpm] - [rpm]

r0065 Slip frequency / f_SlipAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 2_1 Unit selection: p0505 Func. diagram: 6310, 6700, 6727,

6730, 6732Min Max Factory setting - [Hz] - [Hz] - [Hz]

r0066 CO: Output frequency / f_outpAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2000 Dyn. index: -Unit group: 2_1 Unit selection: p0505 Func. diagram: 6300, 6700, 6730,

6731, 6799Min Max Factory setting - [Hz] - [Hz] - [Hz]



Dependency: Refer to: r0024Note: The output frequency is available smoothed (r0024) and unsmoothed (r0066).

Description: Display and connector output for the maximum output current of the power unit.Dependency: The maximum output current is determined by the parameterized current limit and the motor and converter thermal

protection.Refer to: p0290, p0640

Description: Displays actual absolute current.Index: [0] = Unsmoothed

[1] = Smoothed with p0045Dependency: Refer to: r0027Notice: The value is updated with the current controller sampling time.Note: Absolute current value = sqrt(Iq^2 + Id^2)

The absolute value of the current actual value is available smoothed (r0027 with 300 ms, r0068[1] with p0045) and unsmoothed (r0068[0]).

Description: Display and connector output for the measured actual phase currents as peak value.Index: [0] = Phase U

[1] = Phase V[2] = Phase W[3] = Phase U offset[4] = Phase V offset[5] = Phase W offset[6] = Total U, V, W[7] = Alpha component[8] = Beta component

Note: In indices 3 ... 5, the offset currents of the 3 phases, which are added to correct the phase currents, are displayed.The sum of the 3 corrected phase currents is displayed in index 6.

r0067 CO: Output current maximum / I_outp maxAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 6300, 6640, 6724Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0068[0...1] CO: Absolute current actual value / I_act abs valAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 6300, 6714, 6799,

7017, 8017, 8018, 8019Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0069[0...8] CO: Phase current actual value / I_phase act valAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_5 Unit selection: p0505 Func. diagram: 6730, 6731Min Max Factory setting - [A] - [A] - [A]



Description: Display and connector output for the measured actual value of the DC link voltage.Dependency: Refer to: r0026Notice: When measuring a DC link voltage < 200 V, for the Power Module a valid measured value is not supplied. In this

case, when an external 24 V power supply is connected, a value of approx. 24 V is displayed in the display parameter.

Note: The DC link voltage is available smoothed (r0026) and unsmoothed (r0070).

Description: Displays the maximum output voltage.Dependency: The maximum output voltage depends on the actual DC link voltage (r0070) and the maximum modulation depth

(p1803).Note: As the (driven) motor load increases, the maximum output voltage drops as a result of the reduction in DC link

voltage.

Description: Display and connector output for the actual output voltage of the power unit.Dependency: Refer to: r0025Note: The output voltage is available smoothed (r0025) and unsmoothed (r0072).

Description: Displays the maximum modulation depth.Dependency: Refer to: p1803

r0070 CO: Actual DC link voltage / Vdc act valAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: 5_2 Unit selection: p0505 Func. diagram: 6723, 6724, 6730,

6731, 6799Min Max Factory setting - [V] - [V] - [V]

r0071 Maximum output voltage / U_output maxAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: 5_1 Unit selection: p0505 Func. diagram: 6301, 6640, 6700,

6722, 6723, 6724, 6725, 6727Min Max Factory setting - [Vrms] - [Vrms] - [Vrms]

r0072 CO: Output voltage / U_outputAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: 5_1 Unit selection: p0505 Func. diagram: 5700, 6730, 6731,

6799Min Max Factory setting - [Vrms] - [Vrms] - [Vrms]

r0073 Maximum modulation depth / Modulat_depth maxAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6723, 6724Min Max Factory setting - [%] - [%] - [%]



Description: Display and connector output for the actual modulation depth.Dependency: Refer to: r0028Note: For space vector modulation, 100% corresponds to the maximum output voltage without overcontrol.

Values above 100 % indicate an overcontrol condition - values below 100% have no overcontrol.The phase voltage (phase-to-phase, rms) is calculated as follows:(r0074 x r0070) / (sqrt(2) x 100 %).The modulation depth is available smoothed (r0028) and unsmoothed (r0074).

Description: Display and connector output for the field-generating current setpoint (Id_set).Note: This value is irrelevant for the U/f control mode.

Description: Display and connector output for the field-generating current actual voltage (Id_act).Dependency: Refer to: r0029Note: This value is irrelevant for the U/f control mode.

The field-generating current actual value is available smoothed (r0029) and unsmoothed (r0076).

Description: Display and connector output for the torque-generating current setpoint.Note: This value is irrelevant for the U/f control mode.

r0074 CO: Modulat_depth / Mod_depthAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 5730, 6730, 6731,

6799, 8940, 8950Min Max Factory setting - [%] - [%] - [%]

r0075 CO: Current setpoint field-generating / Id_setAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 6700, 6714, 6725Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0076 CO: Current actual value field-generating / Id_actAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 5700, 5714, 5730,

6700, 6714, 6799Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0077 CO: Current setpoint torque-generating / Iq_setAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 6700, 6710Min Max Factory setting - [Arms] - [Arms] - [Arms]



Description: Display and connector output for the torque-generating current actual voltage (Iq_act).Dependency: Refer to: r0030Note: This value is irrelevant for the U/f control mode.

The torque-generating current actual value is available smoothed (r0030 with 300 ms) and unsmoothed (r0078).

Description: Display and connector output for the torque setpoint at the output of the speed controller.

Description: Display and connector output for actual torque value.Index: [0] = Unsmoothed

[1] = Smoothed with p0045Dependency: Refer to: r0031, p0045Note: The value is available smoothed (r0031 with 100 ms, r0080[1] with p0045) and unsmoothed (r0080[0]).

Description: Displays the torque utilization as a percentage.The torque utilization is obtained from the required smoothed torque referred to the torque limit.

Dependency: This parameter is only available for vector control. For U/f control r0081 = 0 %.Refer to: r0033

Note: The torque utilization is available smoothed (r0033) and unsmoothed (r0081).The torque utilization is obtained from the required torque referred to the torque limit as follows:- Positive torque: r0081 = (r0079 / r1538) * 100 %- Negative torque: r0081 = (-r0079 / -r1539) * 100 %

r0078 CO: Current actual value torque-generating / Iq_actAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2002 Dyn. index: -Unit group: 6_2 Unit selection: p0505 Func. diagram: 6310, 6700, 6714,

6799Min Max Factory setting - [Arms] - [Arms] - [Arms]

r0079 CO: Torque setpoint / M_setAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2003 Dyn. index: -Unit group: 7_1 Unit selection: p0505 Func. diagram: 6020, 6060, 6710Min Max Factory setting - [Nm] - [Nm] - [Nm]

r0080[0...1] CO: Torque actual value / M_actAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2003 Dyn. index: -Unit group: 7_1 Unit selection: p0505 Func. diagram: 6714, 6799Min Max Factory setting - [Nm] - [Nm] - [Nm]

r0081 CO: Torque utilization / M_UtilizationAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8012Min Max Factory setting - [%] - [%] - [%]



Description: Displays the instantaneous active power.Index: [0] = Unsmoothed

[1] = Smoothed with p0045[2] = Electric power

Dependency: Refer to: r0032Note: The mechanical active power is available smoothed (r0032 with 100 ms, r0082[1] with p0045) and unsmoothed

(r0082[0]).

Description: Displays the flux setpoint.

Description: Displays the flux actual value.Index: [0] = Unsmoothed

[1] = Smoothed

Description: Displays the actual active power factor.This value refers to the electrical power of the basic fundamental signals at the output terminals of the converter.

Description: Displays the actual phase voltage.Index: [0] = Phase U

[1] = Phase V[2] = Phase W

Note: The values are determined from the transistor power-on duration.

r0082[0...2] CO: Active power actual value / P_actAccess level: 3 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: r2004 Dyn. index: -Unit group: 14_5 Unit selection: p0505 Func. diagram: 6714, 6799Min Max Factory setting - [kW] - [kW] - [kW]

r0083 CO: Flux setpoint / Flex setpAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 5722Min Max Factory setting - [%] - [%] - [%]

r0084[0...1] CO: Flux actual value / Flux act valAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: PERCENT Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6730, 6731Min Max Factory setting - [%] - [%] - [%]

r0087 CO: Actual power factor / Cos phi actAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - -

r0089[0...2] Actual phase voltage / U_phase act valAccess level: 4 Calculated: - Data type: FloatingPoint32Can be changed: - Scaling: p2001 Dyn. index: -Unit group: 5_3 Unit selection: p0505 Func. diagram: 6719Min Max Factory setting - [V] - [V] - [V]



Description: Setting the commissioning and control view for various application classes.Value: 0: Expert

1: Standard drive control2: Dynamic drive control

Dependency: The parameter is preset when commissioning the system for the first time and for the factory setting, depending on the power unit that is connected.Depending on the setting, the ability to see control parameters is restricted depending on the particular application.For p0096 > 0, the motor data identification is preset (p1900 = 12). With this setting, after the motor data identification, the system immediately goes into operation.p0096 = 1: motor type (p0300) synchronous or reluctance motor not possible.

Note: When changing p0096 to 1 or 2, when completing commissioning, fast parameterization should be executed (p3900 > 0).Depending on the setting, after quick commissioning and/or automatic parameterization, the procedure for motor data identification as well as the setting of the operating mode and parameterization of the closed-loop control must be appropriately adapted.

Description: Defines whether the motor and drive converter power settings (e.g. rated motor power, p0307) are expressed in [kW] or [hp].Depending on the selection, the rated motor frequency (p0310) is either set to 50 Hz or 60 Hz.For p0100 = 0, 2, the following applies: The power factor (p0308) should be parameterized.For p0100 = 1, the following applies: The efficiency (p0309) should be parameterized.

Value: 0: IEC-Motor (50 Hz, SI units)1: NEMA motor (60 Hz, US units)2: NEMA motor (60 Hz, SI units)

Dependency: If p0100 is changed, all of the rated motor parameters are reset. Only then are possible unit changeovers made.The units of all motor parameters are changed that are involved with the selection IEC or NEMA.Refer to: r0206, p0210, p0300, p0304, p0305, p0307, p0308, p0309, p0310, p0311, p0314, p0320, p0322, p0323, p0335, p1800

Note: The parameter value is not reset when the factory setting is restored (p0010 = 30, p0970).

Description: Identification of the Control Unit using an LED.Note: While p0124 = 1, the READY LED flashes green/orange or red/orange with 2 Hz at the appropriate Control Unit.

p0096 Application class / Appl_classAccess level: 1 Calculated: - Data type: Integer16Can be changed: C(1) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 6019Min Max Factory setting 0 2 0

p0100 IEC/NEMA mot stds / IEC/NEMA mot stdsAccess level: 1 Calculated: - Data type: Integer16Can be changed: C(1) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 2 0

p0124[0...n] CU detection via LED / CU detection LEDAccess level: 3 Calculated: - Data type: Unsigned8Can be changed: U, T Scaling: - Dyn. index: PDSUnit group: - Unit selection: - Func. diagram: -Min Max Factory setting 0 1 0



Description: Configuration of the motor when commissioning the motor.

Dependency: For standard induction motors (p0301 > 10000), bit 0 is automatically preassigned the connection type of the selected data set.For p0100 > 0 (60 Hz rated motor frequency), it is not possible to select bit 1.Refer to: p0304, p0305, p1082

Note: Re bit 00:When changing the bits, the rated motor voltage p0304 and the rated motor current p0305 are automatically converted to the selected connection type (star/delta).Re bit 01:87 Hz operation is only possible in the delta connection type. When selected, the maximum speed p1082 is automatically preassigned for a maximum output frequency of 87 Hz.

Description: Sets the number of Command Data Sets (CDS).Dependency: Refer to: p0010, r3996Notice: When the data sets are created, short-term communication interruptions may occur.Note: It is possible to toggle between command parameters (BICO parameters) using this data set changeover.

Description: Sets the number of Drive Data Sets (DDS).Dependency: Refer to: p0010, r3996Notice: When the data sets are created, short-term communication interruptions may occur.

Description: Displays the bootloader version.Index 0:Displays the bootloader version.

p0133[0...n] Motor configuration / Motor configAccess level: 2 Calculated: - Data type: Unsigned16Can be changed: C(1, 3) Scaling: - Dyn. index: MDSUnit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - 0000 bin

Bit field: Bit Signal name 1 signal 0 signal FP00 Motor connection type Delta Star -01 Motor 87 Hz operation Yes No -

p0170 Number of Command Data Sets (CDS) / CDS countAccess level: 2 Calculated: - Data type: Unsigned8Can be changed: C(15) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8560Min Max Factory setting 2 2 2

p0180 Number of Drive Data Sets (DDS) / DDS countAccess level: 3 Calculated: - Data type: Unsigned8Can be changed: C(15) Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: 8565Min Max Factory setting 1 2 1

r0197[0...1] Bootloader version / Bootloader versAccess level: 4 Calculated: - Data type: Unsigned32Can be changed: - Scaling: - Dyn. index: -Unit group: - Unit selection: - Func. diagram: -Min Max Factory setting - - -



Index 1:Displays the bootloader version 3 (for CU320-2 and CU310-2)Value 0 means that boot loader 3 is not available.

Dependency: Refer to: r0018, r0198Note: Example:

list manual g120c - siemens · 12 list manual (lh13), 04/2015, a5e33840768 2.1 overview of...

Documents