level plus - mts sensors · 2020-03-17 · level plus ® magnetostrictive ... 6a heavy oils...

Operation Manual

Level Plus®

Magnetostrictive Liquid Level Transmitterswith Temposonics® Technology

CHAMBERED

Table of contents

1. Contact information ........................................................................................................................................... 32. Terms and definitions ......................................................................................................................................... 33. Introduction ..................................................................................................................................................... 5

3.1 Purpose and use of this manual ................................................................................................................................................................ 53.2 Used symbols and warnings ..................................................................................................................................................................... 5

4. Safety instructions ............................................................................................................................................. 54.1 Intended use .............................................................................................................................................................................................. 54.3 Installation, commissioning and operation ................................................................................................................................................ 6

5. Product overview .............................................................................................................................................. 65.1 Components .............................................................................................................................................................................................. 64.2 Foreseeable misuse ................................................................................................................................................................................... 65.2 Accuracy .................................................................................................................................................................................................... 85.3 Warranty .................................................................................................................................................................................................... 85.4 Storage ...................................................................................................................................................................................................... 85.5 Model number identification ...................................................................................................................................................................... 95.6 Technical data .......................................................................................................................................................................................... 11

6. Installation and mounting ...................................................................................................................................126.1 Training ................................................................................................................................................................................................... 126.2 Tools ........................................................................................................................................................................................................ 126.3 Installation steps ..................................................................................................................................................................................... 126.4 Mounting ................................................................................................................................................................................................. 12

7. Electrical connections ........................................................................................................................................137.1 Basic information .................................................................................................................................................................................... 137.2 Safety recommendations ......................................................................................................................................................................... 137.3 Industrial topologies ................................................................................................................................................................................ 137.4 Cable recommendations .......................................................................................................................................................................... 147.5 Electrical conduit ..................................................................................................................................................................................... 147.6 Grounding ............................................................................................................................................................................................... 157.7 Safety barriers ......................................................................................................................................................................................... 15

8. Commissioning................................................................................................................................................168.1 Training ................................................................................................................................................................................................... 168.2 Tools ........................................................................................................................................................................................................ 168.3 Setup software ........................................................................................................................................................................................ 168.4 Commissioning steps .............................................................................................................................................................................. 16

9. Maintenance ...................................................................................................................................................179.1 Training ................................................................................................................................................................................................... 179.2 Tools ........................................................................................................................................................................................................ 179.3 Inspection ................................................................................................................................................................................................ 179.4 Preventative maintenance ........................................................................................................................................................................ 17

10. Repair .........................................................................................................................................................1710.1 RMA policy ............................................................................................................................................................................................ 1710.2 Training ................................................................................................................................................................................................. 1710.3 Tools ...................................................................................................................................................................................................... 1710.4 Troubleshooting..................................................................................................................................................................................... 1710.5 Setup software ...................................................................................................................................................................................... 18

11. Spare Parts ...................................................................................................................................................1812. Interface ......................................................................................................................................................18

12.1 Modbus ................................................................................................................................................................................................. 1812.2 DDA ....................................................................................................................................................................................................... 1812.3 HART® .................................................................................................................................................................................................. 18

13. Agency information .........................................................................................................................................1913.1 Approvals overview ............................................................................................................................................................................... 1913.2 Certificates ............................................................................................................................................................................................ 2013.3 FM (NEC) ............................................................................................................................................................................................... 2013.4 FMC (CEC) ............................................................................................................................................................................................. 3113.5 ATEX and IECEx ..................................................................................................................................................................................... 46

Level Plus® CHAMBEREDOperation Manual

I 3 I

1. Contact information

United States

GeneralTel: +1-919-677-0100Fax: +1-919-677-2343E-mail: [email protected]://www.mtssensors.com

Mailing and shipping addressMTS Systems CorporationSensors Division3001 Sheldon DriveCary, North Carolina, 27513, USA

Customer serviceTel: +1-800-633-7609Fax: +1-800-498-4442E-mail: [email protected]

Technical support and applications24 Hour Emergency Technical SupportTel: +1-800-633-7609E-mail: [email protected]

Germany

GeneralTel: +49-2351-9587-0Fax: +49-2351-56491E-mail: [email protected]://www.mtssensors.com

Mailing and shipping addressMTS Sensor Technologie, GmbH & Co. KGAuf dem Schüffel 958513 Lüdenscheid, Germany

Technical support and applicationsTel: +49-2351-9587-0E-mail: [email protected]://www.mtssensors.com

2. Terms and definitions

6A Heavy Oils‘Generalized Crude Oils’, Correction of Volume to 60 °F against API Gravity.

6B Light Oils‘Generalized Products’, Correction of Volume to 60 °F against API Gravity.

6C Chemical‘Volume Correction Factors (VCF)’ for individual and special applications, volume correction to 60 °F against thermal expansion coefficients.

6C ModAn adjustable temperature reference for defining VCF.

A

API gravity The measure of how heavy or light a petroleum liquid is compared to water. Allowable values are 0 to 100 degrees API for (6A) and 0 to 85 degrees API for (6B).

D

DDA (Direct Digital Access)The proprietary digital protocol developed by MTS for use in intrinsically safe areas.

Density Mass divided by the volume of an object at a specific temperature. The density value should be entered as lb / cu. ft.

E

Explosion proof Type of protection based on enclosure in which the parts which can ignite an explosive gas atmosphere are placed within, and which can withstand the pressure developed during an internal explosion of an explosive mixture, and which prevents the transmission of the explosion to the explosive gas atmosphere surrounding the enclosure.

F

Flameproof Type of protection based on enclosure in which the parts which can ignite an explosive gas atmosphere are placed within and which can withstand the pressure developed during an internal explosion of an explosive mixture, and which prevents the transmission of the explosion to the explosive gas atmosphere surrounding the enclosure.

mailto:info.us%40mtssensors.com?subject=

http://www.mtssensors.com

mailto:info.us%40mtssensors.com?subject=

mailto:levelplus%40mts.com?subject=

mailto:info.de%40mtssensors.com?subject=


mailto:info.de%40mtssensors.com?subject=



I 4 I

G

GOVI (Gross Observed Volume of the Interface)The total volume of the tank occupied by the interface liquid. The GOVI is only given when measuring two liquids and is calculated by subtracting the volume of the product from the total volume of liquid in the tank (GOVT – GOVP).

GOVP (Gross Observed Volume of the Product)The total volume of the tank occupied by the product liquid. When measuring only one liquid, it is also the total volume of liquid in the tank (GOVT). When measuring two liquids it is the total volume of liquid in the tank minus the volume of the interface liquid (GOVT – GOVI).

GOVT (Total Gross Observed Volume)The total volume of liquid in the tank. When measuring only one liquid it is equal to the volume of the product (GOVP). When measuring two liquids it is equal to the volume of the product and interface liquids (GOVP + GOVI).

GOVU (Gross Observed Volume Ullage)The difference in volume between the working capacity of a tank and the total volume in the tank (Working Capacity – GOVT).

H

HART®

A Bidirectional communication protocol that provides data access between intelligent field instruments and host systems.

I

Interface Noun; The measurement of the level of one liquid when that liquid is below another liquid.

Interface Adj.; The Software Graphical User Interface (GUI) that allows the user to access software protocols (HART®, DDA, MODBUS).

Intrinsic safety ‘Intrinsically safe’ - Type of protection based on the restriction of electrical energy within apparatus of interconnecting wiring exposed to potentially explosive atmosphere to a level below that which can cause ignition by either sparking or heating effects.

M

Mass The property of a body that causes it to have weight in a gravitational field, calculated by density at the reference temperature multiplied by the volume correction factor (Density × VCF).

MODBUS A serial communications protocol published by Modicon in 1979 for use with its programmable logic controllers (PLCs). It has become a de facto standard communications protocol in industry, and is now the most commonly available means of connecting industrial electronic devices.

N

NEMA Type 4X A product Enclosure intended for indoor or outdoor use primarily to provide a degree of protection against corrosion, windblown dust and rain, splashing water, and hose-directed water; and to be undamaged by the formation of ice on the enclosure. They are not intended to provide protection against conditions such as internal condensation or internal icing.

NPT U.S. standard defining tapered pipe threads used to join pipes and fittings.

NSVP (Net Standard Volume of the Product)The temperature corrected volume for the product liquid in the tank, requires the transmitter to be ordered with temperature measurement capabilities. The NSVP is calculated by multiplying the volume of the product liquid by a volume correction factor based on temperature (GOVP × VCF).

R

Reference Temperature The temperature at which the density measurement is given, the allowable values are 32 °F to 150 °F (0 °C to 66 °C).

S

Specific Gravity The density ratio of a liquid to the density of water at the same conditions.

Sphere Radius The internal radius of the sphere that contains the liquid, the value is used to calculate the volume along with the Sphere Offset.

Sphere OffsetAn offset value that accounts for additional volume in a sphere from non-uniform sphere geometry, the value is used to calculate the volume along with the Sphere Radius.


I 5 I

Strap TableA table of measurement correlating the height of a vessel to the volume that is contained at that height. The transmitter can contain up to 200 points.

T

TEC ‘Thermal Expansion Coefficient’ - a value correlating the change in temperature for an object with the change in its volume. Allowable values are 270.0 to 930.0. TEC units are in 10 E-6/Deg F.

Temperature Correction Method One of five product correction methods used to correct the product volume in the tank due to changes in temperature from 60 °F including (6A, 6B, 6C, 6C Mod, and Custom Table.

V

Volume Calculation Mode One of two methods use to calculate volume measurements from level measurements, including Sphere and Strap Table.

VCF (Volume Correction Factor) A table of measurements correlating temperature points with correction factors for the liquids expansion/contraction. The transmitter can contain up to 50 points.

W

Working Capacity The maximum volume of liquid that the user desires for their vessel to hold, typically 80% of the vessels maximum volume before overfill.

3. Introduction

3.1 Purpose and use of this manual

Important:Before starting the operation of the equipment read this documentation thoroughly and follow the safety information.

The content of this technical documentation and of its various annexes is intended to provide information on mounting, installation and commissioning by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians.

3.2 Used symbols and warnings

Warnings are intended for your personal safety and for avoidance of damage to the described product or connected devices. In this documentation, safety information and warnings to avoid dangers that might affect the life and health of personnel or cause material damage are highlighted by the preceding pictogram, which is defined below.

Symbol Meaning

NOTICE This symbol is used to point to situationsthat may lead to material damage and/or personal injury.

4. Safety instructions

4.1 Intended use

The liquid level transmitter is intended to be used to measure the level of liquid(s) contained by a structure as well as the temperature of the liquid. The product may only be used for the applications defined under item 1 to item 4 and only in conjunction with third-party devices and components recommended or approved by MTS Sensors. As a prerequisite of proper and safe operation, the product requires correct transport, storage, mounting and commissioning and must be opera-ted with utmost care.

1. Application does not exceed product’s performance specification in chapter 5.6.

2. Product may only be installed in hazardous areas as specified by approval certifications in chapter 13 following special conditions of use outlined in chapter 13 or in safe areas.

3. The liquid(s) being measured are compatible with the selected wetted parts of the product.

4. MTS floats should be used for proper functionality and safety approval.


I 6 I

Forseeable misuse ConsequenceWrong sensor connection Possible damage to electronics

See chapter 7 for Electrical Connections

Improper Installation Physical damage to packagingSee chapter 6 for Installation

Installation in unapproved Hazardous Area

Potential SparkSee chapter 13 for Agency Information

Process Temperature out of range Signal Degradation, Possible Damage to SensorSee chapter 5.6 for Specifications

Power Supply out of range No Communication, Possible Damage to SensorSee chapter 5.6 for Specifications

Process Pressure out of range Possible Damage to Sensor,See chapter 5.6 for Specifications

Improper Chemical Compatibility Possible Damage to Sensor,Customer Must Select Wetted Material that is compatible with liquid(s) in tank

Modifying Sensor Warranty Void, Hazardous Approval Void Customer should contact factory for custom unit

Improper Grounding Possible Damage to Sensor, Full Protection Compromised,See chapter 7.6 for Grounding

Table 1: Foreseeable misuse

4.3 Installation, commissioning and operation

1. Wear proper personal protection equipment such as hard hat, safety shoes, flame resistant clothing, safety glasses, gloves, and hearing protection.

2. Follow the specifications given in the technical documentation. 3. Two (2) individuals are recommended to conduct proper

installation, commissioning, and repair of the level transmitter. 4. Ensure the equipment used in a hazardous environment is

selected and installed in compliance with regulations governing the geographical installation and facility. Only install equipment that complies with the types of protection relevant to the applicable classes, division, zones, category, gas group, and temperature code.

5. Protect the sensor against mechanical damage during installation and operation.

6. Do not use damaged products and secure them against unintentional use. Mark damaged products as being defective.

7. Connect the sensor very carefully and pay attention to the polarity of connections. MTS recommends to not make connections while power is live.

8. Before turning on power, ensure that nobody’s safety is jeopardized by starting level transmitter and/or process.

9. Regularly follow preventative maintenance to prevent safety risks

4.2 Foreseeable misuse 10. Make sure that no wire strands are loose or sticking out of the terminal block connection which could short and cause a problem.

11. Make sure that no wire strands, including shield, are in contact with the electronic module enclosure.

5. Product overview

The Level Plus® CHAMBERED Liquid-Level transmitter is a continuous multi-functional magnetostrictive transmitter that provides product level and interface level to the user via Modbus, DDA, Analog (4 to 20 mA), or HART. Magnetostrictive technology is one of the most accurate and repeatable level technologies available to date.

MTS is the inventor and purveyor of magnetostrictive technology and has been serving the level industry for over 35 years.

Industries• Petroleum• Liquid Petroleum Gas• Pharmaceutical• Food & Beverage• Chemical• Mining

5.1 Components

The Level Plus® CHAMBERED liquid level transmitter consists of three main components; a housing, outer pipe, and electronics. Varying the components of the transmitter allows the transmitter to be customized to almost any application.

HousingsLevel Plus® CHAMBERED transmitters are available in two housing configurations: single and dual cavity housings as shown below. The conduit openings on the single cavity housings (options D, L) and standard electronic mount (7,8) are 3/4" NPT opening for FM and FMC approvals and M20 opening for ATEX and IECEx approvals. The conduit openings on the single cavity housing (options D,L) and 90 degree electronic mount (3,4,5,6) are 3/4" NPT for all approvals and a M20 adapter is supplied for ATEX and IECEx approvals. The conduit opening on the dual cavity housing option (E) always requires the 90 degree electronic mount (3,4,5,6) and is supplied with 3/4" NPT opening for FM and FMC approvals and M20 opening for ATEX and IECEx approvals.


I 7 I

Fig. 1: Single cavity housing

Fig. 2: Dual cavity housing

1

1

2

2

3

3

4

4

A A

B B

C C

D D

REV ECO # DESCRIPTION

TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF

UNLESS OTHERWISE SPECIFIEDTOLERANCES

0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1

- THREAD DEPTHS ARE TO MIN. FULL THDS- DRILL DEPTHS ARE TO FULL DIA.- REMOVE BURRS AND SHARP EDGES- DO NOT SCALE PRINT- MACHINED SURFACE FINISH 3.2uM [125 uIn]

PROPRIETARY DATATHE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

mMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

METRIC

FIRST ANGLE C LL drawing

1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METRIC

FIRST ANGLE C LL drawing

1 1

DRAWN BY:

114 mm(4.5 in.)

127 mm(5 in.)

124 mm(4.9 in.)

132 mm(5.2 in.)

87 mm(3.4 in.)

109 mm(4.3 in.)

75 mm(3 in.)

206 mm(8.1 in.)

127 mm(5 in.)

117 mm(4.6 in.)

145 mm(5.7 in.)

Fig. 3: Stainless steel single cavity housing

1

1

2

2

3

3

4

4

A A

B B

C C

D D

TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE: SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METRIC

FIRST ANGLE C

1 1

DRAWN BY:

REV ECO# DESCRIPTION BY DATE

178 mm(7 in.)

135 mm(5.30 in.)

135 mm(5.3 in.)

152 mm(6 in.)

1

1

2

2

3

3

4

4

A A

B B

C C

D D

TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE: SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METRIC

FIRST ANGLE C

1 1

DRAWN BY:

REV ECO# DESCRIPTION BY DATE

178 mm(7 in.)

135 mm(5.30 in.)

135 mm(5.3 in.)

152 mm(6 in.)

Outer pipe configurationsThe outer pipe is constructed of a variety of configurations. The CHAMBERED is available in a rigid pipe. For other pipe options please consult other MTS options such as Tank Slayer®, RefineMe®, SoClean®, and/or USTDII. USTDII.Floats

1

1

2

2

3

3

4

4

A A

B B

C C

D D


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METRIC

FIRST ANGLE C Marketing

1 1

DRAWN BY:

***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION TO APPROVAL AGENCY(S).***

Order length

304.8mm (12 in)

Pipe diameter16mm (0.625 in)

Tip of transmitter

Tank Flange

1 in NPT Adjustablecompression fitting, male

127mm [5 in ]

Order Length

Pipe diameter (0.625 in. dia)constructed of 316l stainless steel

Sanitary process connection (sanitary cap)

74 mm (2.9 in.) minInactive zone

Order Length

54 mm (2.1 in.)minimum

Fig. 4: Stainless steel single cavity housing


I 8 I

Internal electronicsAll transmitters come with two electronic components of a sensing element and a board set. Rigid sensing elements are standard on CHAMBERED. The board set consists of up to three electronic boards and a display.

A temperature sensing function is optional with the CHAMBERED transmitter. The temperature sensing device is a Digital Thermometer mounted inside the transmitter’s outer pipe assembly. The CHAMBERED can be ordered with 1, 5, 12, or 16 temperature points.

DisplayAll LP-Series liquid level transmitters are shipped with a stylus (MTSPart # 404108) to be used for manipulating the display. For single anddual cavity housings, the stylus is designed to allow for programmingof the unit without removing the housing. When using the stylus makesure to align the stylus with the shape outline around the buttons inthe same orientation. Failure to correctly align the stylus can cause thedisplay to not function properly. Password for entering the menu is 27513. For additional details consult the protocol specific Modbus Interface Manual (MTS Part #551700), DDA Interface Manual (MTS Part #551701), and HART® Interface Manual (MTS Part #551702).

Fig. 5: Stylus (MTS Part # 404108)

AccessoriesMTS also offers a series of displays, housings, converters, and other accessories, please refer to the ‘Accessories Catalog’, (MTS Part #551103).

Fig. 6: Display

5.2 Accuracy

For magnetostrictive transmitters inherent accuracy is measured in terms of non-linearity. Non-linearity is a measurement of any imperfections in the waveguide that are reflected in the linearity of the transmitter’s output. MTS tolerances reflect a maximum non-linearity of ±1mm. MTS is able to achieve such strict tolerances by manufacturing all of its own waveguide from a proprietary alloy and testing 100% of all transmitters before shipping.

5.3 Warranty

Important:Contact Technical Support or Customer Service for assistance if you suspect that the transmitter is not working correctly. Technical support can assist you with troubleshooting, part replacement, and Returned Material Authorization (RMA) information if required.

All Level Plus® transmitters come with a two year limited warranty from the factory shipment date. An additional extended warranty can be purchased. A Return Materials Authorization (RMA) number is required and must accompany any transmitter returns. Any unit that was used in a process must be properly cleaned in accordance with OSHA standards, before it is returned to the factory. A Material Safety Data Sheet (MSDS) must also accompany the transmitter that was used in any process.

5.4 Storage

http://www.mtssensor.de/fileadmin/medien/download/Accessorie/Accessories_LiquidLevel_551103_EN.pdf


I 9 I

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

L P C

a b c d e f g h i j k l m n o p

a Sensor model

L P C CHAMBERED Level Transmitter

b Output

M Modbus

D DDA

3 1 Loop with HART®

6 1 Loop with HART® and SIL 2

d Electronics mounting

3 90° bend housing top left

4 90° bend housing top right

5 90° bend housing bottom left

6 90° bend housing bottom right

7 Top mount

8 Bottom mount

f Materials of construction (Wetted parts)*

1 316L stainless steel

e Sensor pipe

B 5/8" OD pipe

R 1/2" OD pipe

Y 10 mm OD pipe

c Housing type

D Single cavity with display

E Dual cavity with display

L SS single cavity w/display

*/ Contact factory for other materials

5.5 Model number identification

g Process connection type

X None

h Process connection size

X None

i Number of DT‘s (Digital Thermometers)

0 None

j DT‘s placement

X None

l Protection method

F Explosion proof / Flameproof (only for housing type D, E, or L)

I Intrinsically safe

X No approval

m Gas group

A Group A (not available with “C = CEC (FMC)” notified body and “F = Flameproof/Explosion proof” protection method)

B Group B

C Group C

D Group D

3 IIC (Instrinsically Safe only)

4 IIB + H2 (Explosion Proof / Flameproof only)

X None

Continued on next page...

k Notified body

B INMETRO

C CEC (FMC)

E ATEX

F NEC (FM)

I IEC

K KC

N NEPSI

T CML/TIIS

P CCOE

X None


I 10 I

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

L P T

a b c d e f g h i j k l m n o p

n Unit of measure

M Millimeters (Metric)

U Inches (US customary)

p Special

S Standard product

o Length (no decimal spaces) *

X X X X X Rigid Pipe: 12 to 144 in (code as 01200 to 14400)

X X X X X Rigid Pipe: 305 to 3658 mm (code as 00305 to 03658)

NOTICE

Accessories such as floats, cables, and remote displays have to be ordered separately. All accessories are shown in the Accessories Catalog (MTS Part #551103).

*/ Contact factory for longer lengths

http://www.mtssensor.de/fileadmin/medien/download/Accessorie/Accessories_LiquidLevel_551103_EN.pdf


I 11 I

5.6 Technical data

Level Output

Measured Variable Product level

Output Signal /Protocol Modbus RTU, DDA, Analog (4…20 mA), HART®

Order Length305 mm (12 in.) to 3658 mm (144 in.) (order length equals the measurement range plus the inactive zone / contact factory for longer lengths)

Inherent Accuracy ±1 mm (0.039 in.)

Repeatability 0.001% F.S. or 0.381 mm (0.015 in.) whichever is greater * (any direction)

Temperature Output

Measured Variable Average and multipoint temperatures (Modbus, DDA)Single point temperature (Analog, HART®)

Temperature Accuracy (Modbus, DDA) ±0.2 °C (0.4 °F) range −40…−20 °C (−40…−4 °F),±0.1 °C (0.2 °F) range −20…+70 °C (−4…+158 °F),±0.15 °C (0.3 °F) range +70…+100 °C (+158…+212 °F),±0.5 °C (0.9 °F) range +100…+105 °C (+ 212 …221 °F)

Temperature Accuracy (Analog, HART®) ±0.28 °C (0.5 °F) range −40…+105 °C (−40…+221 °F)

Electronics

Input Voltage 10.5…28 VDC

Fail Safe High, Full scale (Modbus, DDA)Low, 3.5 mA default or High, 22.8 mA (Analog, HART®)

Reverse Polarity Protection Series diode

EMC EN 61326-1, EN 61326-2-3, EN 61326-3-2, EN 61000-6-2, EN 61000-6-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11

Environmental

Enclosure Rating NEMA Type 4X, IP65

Humidity 0…100% relative humidity, non-condensing

Operating Temperatures Electronics: −40…+71 °C (−40…+160 ºF)Sensing element: −40…+125 °C (−40…+257 °F) (contact factory for specific temperature ranges)

Materials 316L stainless steel, Epoxy coated aluminum

Field Installation

Housing Dimensions Single cavity: 145 mm (5.7 in.) W × by 127 mm (5 in.) D × 109 mm (4.3 in.) H Dual cavity: 117 mm (4.6 in.) W × by 127 mm (5 in.) D × 206 mm (8.1 in.) H Stainless steel single cavity: 178 mm (7.1 in.) W × by 135 mm (5.3 in.) D × 153 mm (6 in.) H

Mounting

Flexible hose 1 in. Adjustable MNPT or BSPP fitting, Flange mount

Wiring

Connections 4 wire shielded cable or twisted pair

Electrical connections

Single and dual cavity ¾ in. FNPT conduit opening, M20 for ATEX/IECEx version

NEMA Type 4X ½ in. FNPT conduit opening

Display

Measured variables Product level, interface level and temperature

*/ Only with MTS recommended floats


I 12 I

Inactive Zone74 mm (2.9 in.)

Inactive Zone54 mm (2.1 in.)

Orderlength

MeasuringRange

127 mm(5 in.)

(Circle one)4 mA or 20 mA

Setpoint


Setpoint

Order LengthStandard

74 mm (2.9 in.)Standard

Level Plus

145 mm(5.7 in.)

PressureBarrier

ElectronicHead 155 mm

(6.1 in.)Protection

MethodI or X

195 mm(7.7 in.)

Protection Method

F

6. Installation and mounting

6.1 Training

Warning: When the pipe/hose of the LP-Series level transmitter is installed or removed from the tank the release of flammable vapors will occur. Take all necessary precaution when installing or removing the level transmitter due to the release of flammable vapors.

Installation should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

6.2 Tools

• Channel Lock pliers• Common head screwdriver, slotted screwdriver• Additional tools may be needed dependent on MLG manufacturer

6.3 Installation steps

CautionIt is recommended that assembly and mounting of this transmitter should not be done alone. To ensure proper and safe assembly of the CHAMBERED transmitter, a minimum of two (2) individuals are recommended. Gloves are also recommended. PPE is required for work areas such as safety shoes, safety glasses, hard hat, and fire resistant clothing.

1. Consult Section 4.3 before starting. 2. Perform steps 1-9 in section 8.4.1 for Modbus or DDA.

Perform steps 1-8 in section 8.4.2 for Analog. 3. CHAMBERED should come installed on MLG chamber. Typical

installation uses a mounting bracket or hose clamps to secure CHAMBERED to MLG. Contact MLG manufacture for installation details.

6.4 Mounting

The method of mounting the transmitter is dependent on the MLG in which it is being used. Typical mounting of CHAMBERED is direct to the MLG.

Fig. 7: CHAMBERED mounting, bottom flange

CautionWhen mounting the level transmitter to a MLG, a minimum spacing of 5 inches shall be maintained between the enclosure head and the pressure barrier. The enclosure and pressure barrier are identified in the following depiction.

CautionThe ambient temperature rating, Ta= -40 °C (-40 °F) to 71°C (160 °F), must not be exceeded due to the mounting of the level transmitter to the MLG and exposure to the process temperature.

Direct mountingIn most applications, the CHAMBERED transmitter can be mounted directly to the MLG via hose clamps. Consult the MLG manufacturer for details.


I 13 I

Fig. 10: Bus with spurs topology

(Circle one)

PressureBarrier

ElectronicHead

4 mA or 20 mA

Setpoint

Order LengthStandard


Setpoint

74 mm (2.9 in.)Standard

74 mm (2.9 in.)

54 mm (2.1 in.)

114 mm(4.5 in.)

145 mm(5.7 in.)

127 mm(5 in.)Level Plus

7. Electrical connections

7.1 Basic information

A typical intrinsically safe connection for the Level Plus® CHAMBERED transmitter includes protective safety barriers, a power supply and a reading or monitoring device. Refer to Agency information in chapter 13.

A typical Explosion proof/flameproof connection for the Level Plus® CHAMBERED transmitter includes a power supply and a reading or monitoring device. All cabling is in approved conduit with sealoffs as specified by local electrical code. Refer to agency information in chapter 13.

7.2 Safety recommendations

Be sure to: 1. Always follow applicable local and national electrical codes and

observe polarity when making electrical connections. 2. Never make electrical connections to the CHAMBERED transmitter

with power turned on. 3. Make sure that no wire strands are loose or sticking out of

the terminal block connection which could short and cause a problem.

4. Make sure that no wire strands, including shield, are in contact with the electronic module enclosure.

5. The electronics module enclosure is grounded through internal circuitry and is electrically isolated from the explosion proof housing.

7.3 Industrial topologies

There are four topologies described and illustrated below. However, the daisy chain topology is not recommended by MTS.

Point-to-pointThe point-to-point topology consists of having only one device on the loop as shown in Fig. 89. This topology is not usually used with a bus network since it does not take advantage of placing multiple devices on a loop.

PLC

Fig. 8: CHAMBERED mounting, top and bottom flange

Bus with spursThe bus with spurs topology has a main trunk cable that has each device connected via its own spur at a junction box as shown in Fig. 90. The bus with spurs and tree topologies can also be used together to form a hybrid topology.

Fig. 9: Point-to-point topology

PLC


I 14 I

Tree alignmentThe tree topology is very similar to the bus with spurs topology with the main difference of having a common junction box for all of the transmitters as shown in Fig. 111. Bus with spurs and tree topologies can also be used together to form a hybrid topology.

Fig. 11: Tree topology

PLC

Daisy chainThe daisy-chain topology utilizes a single cable that is connected to all of the transmitters with the cable being interconnected at each field device. When using this topology make sure that the wiring practice allows for one transmitter to be disconnected without disconnecting the entire loop as shown in Fig. 122. MTS does not suggest using the daisy-chain topology.

Fig. 12: Daisy-chain topology

PLC

Fig. 13: Electrical conduit installation

Table 2: Cable specification and parameters

7.4 Cable recommendations

Refer to ‘Table 2’ below for general requirements of cable types for the Level Plus® CHAMBERED transmitter.

Cable specifications

7.5 Electrical conduit

Parameter Specifitcation

Minimum cable size Ø 0.51…1.6 mm (24…14 AWG)

Cable typeSingle pair shielded or multiple pair with overall shield; minimum 0.25 mm (0.010 in.) insulation thickness

Capacitance Less than 98 pF/m (30 pF/ft)

NOTICE

1. Tighten housing cover (both front and back covers if dual cavity) to full stop against the O-ring.

2. Use side conduit entry only. 3. In high humidity areas, use a breather drain type conduit

sealing fitting to minimize moisture intrusion. 4. For Division Installations, an approved conduit seal is required

within 457 mm (18 in.) of the enclosure. 5. For Zone Installations, an approved conduit seal is required

within 50mm (2 in.) of the enclosure.

Conduit sealing fitting

NPT or BSPP FittingDo not over-tightencompression fitting!

Interface float(ordered

separately)

Product float(ordered

separately)

View shown withcover removed

Plugged entryDo not use(see notes)

3/4 NPT or M20 conduit accessUse NPT conduit fitting only!

Conduit(flexible or rigid)

Conduit fromcontrol room

Level Plus®

Do not remove cover with circuit energized in hazardous locations!

Follow safe work procedures.


I 15 I

7.6 Grounding

7.6.1 Safety grounding

Warning:Grounding the transmitter through a threaded conduit connection does not meet the requirements as a grounding of the sensor for safety.

There are two methods to provide an earth ground connection to the earth ground of the electronics. Either method must result in a resistance of less than 1 Ω. Refer to ’Table 3’ for safety barrier references.

• Run an earth ground through the conduit and connect directly to the earth ground lug inside the housing.

• Run an earth ground directly to the ground lug on the outside of the housing.

7.6.2 Shield grounding

Warning:The shield ground does not meet the requirements as grounding of the sensor for safety.

Immunity performance of the sensor from external sources of surge, burst, RF, radiated emissions and other noise is dependent on a proper ground for the shield of the communications cable. The communications cable shield should be of a braided type and connected to the internal ground lug of the sensor housing.

Runs in a continuous metallic conduitWhen installed inside a dedicated continuous metallic conduit, the conduit provides a level of shielding protection from external interference and a level of ground to the sensor housing. In this case a foil type shielded cable with a drain wire connected to the internal ground lug may be sufficient. Sharing of the metallic conduit with other cables will result in loss of effective shielding performance of the communication cable and possible degradation in performance of the sensor. In this case a braided type shielded cable connected to the sensor internal ground lug would be recommended. In all cases paralleling the communications cable with any noise generating cable inside of a conduit or with noise generating cables in close proximity to the conduit may degrade the performance of the sensor. Runs without a conduitIn some rare applications, or where safety may not be required, a metallic conduit may not exist. The communications cable shield should be of a braided type and connected to the internal ground lug of the sensor housing. Alternatively a safety approved EMC Cable Gland can be used for grounding the shield. Contact MTS for information before using one of these cable glands.

NECUndesirable currents (ground loops) is a violation of the NEC and is a safety hazard.

7.7 Safety barriers

Refer to Table 3 for entity parameters and Table 4 for example safetybarriers.

Entity parameters

Digital supply(1 per LT)

Ui = 28 VDC

Ii = 100 mA

Ci = 0.0 µF

Li = O mH

Pi = 700 mW

Digital communication(2 per LT)

Ui = 8.6 VDC

Ii = 10 mA

Ci = 0.0 µF

Li = 0.0 mH

Pi = 21.5 mW

Analog(1 per loop)

Ui = 28 VDC

Ii = 120 mA

Ci = 0 µF

Li = 5 µH

Pi = 840 mW

Table 3: Safety barrier entity parameter references

Table 4: Safety barrier entity parameter references

Supplier STAHL STAHL STAHL

Type9001/01-280-100-101

9001/51-280-110-141

9001/01-086-010-101

Maximum voltage 28 VDC 28 VDC 8.6 VDCMaximum current(each channel) 100 mA 110 mA 10 mA

Maximum power(each channel) 700 mW 770 mW 21.5 mW

Number of channels 1 1 1

Interface Modbus/DDA HART® Modbus/DDA


I 16 I

8. Commissioning

8.1 Training

Commissioning should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

8.2 Tools

• Channel Lock pliers• RS485 to USB Converter (MTS Part # 380114)[Modbus and DDA]• Windows Based PC• Linear Regulated Power Supply• MTS Setup Software• HART® to USB Converter (MTS Part # 380068)

8.3 Setup software

MTS offers Setup Software that is shipped with the level transmitterand is also available for download from www.mtssensors.com. TheSetup Software is to be used for installation, commissioning, andtroubleshooting. For further details on how to use the setup softwareconsult the Modbus Interface Manual (MTS Part# 551700), the DDAInterface Manual (MTS Part# 551701), and HART® Interface Manual(MTS Part#: 551702).

8.4 Commissioning steps

8.4.1 Modbus or DDA

1. Consult Section 4.3 before starting 2. Remove level transmitter from shipping container. 3. Mount on MLG and test unit with float from MLG 4. Connect power, RS485 to USB converter, and PC. 5. Open MTS Setup Software. 6. Establish Communication. 7. For DDA Interface – Set Address. Default 192. 8. For Modbus Interface – Set Address, Default address 247. 9. Disconnect Power and Communication.

10. Complete Installation in Section 6.4. 11. Have qualified technician perform hand measurement. Enter hand

measurement into MTS Setup Software and calibrate. 12. Store all settings as backup file according to site name and

tank number.

8.4.2 HART®

4. Consult section 4.3 before starting. 5. Remove level transmitter from shipping container. 6. Mount on MLG and test with float from MLG. 7. Connect power, HART® to USB converter, and PC 8. Open MTS Setup Software. 9. Establish Communication.

10. Set/Update 4 and 20 mA setpoints 11. Disconnect Power and Communication. 12. Complete Installation in Section 6.4. 13. Have qualified technician perform hand measurement. Enter

hand measurement into MTS Setup Software and calibrate. 14. Store all settings as backup file according to site name

and tank number

NOTICE

For Additional details consult the protocol specific Modbus InterfaceManual (MTS Part #551700), DDA Interface Manual (MTS Part#551701), and HART® Interface Manual (MTS Part #551702).


I 17 I

9. Maintenance

9.1 Training

Maintenance should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

9.2 Tools

• Channel Lock pliers• Common head screwdriver, slotted screwdriver

9.3 Inspection

Below are some standard items that should be inspected on a regular basis to make sure that the level transmitter and surrounding environment are in operating condition.

• Hazardous Area Label is present and legible• Hazardous Area approval is correct for installation• There are no visible unauthorized modifications• Electrical connections are tight• Condition of enclosure O-ring is satisfactory• No water ingress (white powder)• No obvious damage to cable• Sealing of conduit or cable gland is satisfactory• Earth ground is satisfactory• Single or Dual Cavity Enclosure threads are not damaged• Housing and o-ring are not damaged or cracked• No corrosion on visible parts• Printed circuit boards are clean and undamaged

9.4 Preventative maintenance

Level Plus® level transmitters do not typically require preventative maintenance but may require preventative maintenance dependent on the application. For general purpose applications where there is no potential for buildup on the flexible hose and/or float there is no need for preventative maintenance but routine inspection is still suggested. For severe service applications where there is potential for buildup on the flexible hose and/or float then preventative maintenance is required.

10. Repair

10.1 RMA policy

All Level Plus® transmitters come with a two year limited warranty from the factory shipment date. A Return Materials Authorization (RMA) number is required and must accompany any transmitter returns. Any unit that was used in a process must be properly cleaned in accordance with OSHA standards, before it is returned to the factory. A Material Safety Data Sheet (MSDS) must also accompany the transmitter that was used in any process.

10.2 Training

Repair should only be conducted by qualified service personnel according to IEC 60079-14 and local regulations or MTS trained service technicians. MTS offers web based and in person training for installation, commissioning, maintenance, and repair. MTS also offers factory direct services for these same functions. Contact MTS to discuss training or factory direct services before starting.

10.3 Tools

• Channel Lock pliers• Phillips head screwdriver, plus screwdriver• Common head screwdriver, slotted screwdriver• RS485 to USB Conververter (MTS Part # 380114)

[Modbus and DDA]• Windows Based PC• Linear Regulated Power Supply• HART® to USB Converter (MTS Part # 380068)

Important:Contact Technical Support or Customer Service for assistance if you suspect that the transmitter is not working correctly. Technical support can assist you with troubleshooting, part replacement, and Returned Material Authorization (RMA) information if required.

10.4 Troubleshooting

Symptom Possible cause ActionNo communication with transmitter

No power Check voltage at transmitter

Wiring incorrect Reference installation drawing chapter 13

Wrong address DDA factory default is ‘192 ’ Modbus factory default is ‘247 ’

Wrong software Confirm correct software

Wrong protocol Confirm software and transmitter are same protocol


I 18 I

10.5 Setup software

MTS offers Setup Software that is shipped with the level transmitter and is also available for download from www.mtssensors.com. The Setup Software is to be used for installation, commissioning, and troubleshooting. or further details on how to use the setup software consult the Modbus Interface Manual (MTS Part# 551700), the DDA Interface Manual (MTS Part# 551701), and HART® Interface Manual (MTS Part# 551702).

Table 5: Troubleshooting reference

11. Spare Parts

Below are the spare parts list for the LP-Series show as the display, electronic module, sensing element, and flexible hose. Please contact MTS Technical Support with any questions.

12. Interface

CHAMBERED is available with multiple outputs including Modbus, DDA, and HART®. This Operation and Installation Manual includes all of these outputs. Each output has its own specialized Interface Manual that should be consulted for additional information on the specific output. For SIL consult the SIL Safety Manual, (MTS Part #551851).

12.1 Modbus

MTS offers Modbus RTU over a RS485 half-duplex network. For additional information consult Modbus Interface Manual (MTS Part #551700).

12.2 DDA

MTS offers DDA (Direct Digital Access) over a RS485 half-duplexnetwork. For additional information consult DDA Interface Manual (MTS Part #551701).

12.3 HART®

MTS offers HART® over a 4 to 20 mA signal. For additional informationconsult HART® Interface Manual (MTS Part #551702).

Sensing ElementChange third digit in Model Number from T to E. For example, the sensing element for model number LPTME1N11B5FFIAU50000S is LPEME1N11B5FFIAU50000S.

Flexible HoseChange third digit in Model Number from T to P. For example, the replacement flexible hose for model number LPTME1N11B5FFIAU50000S is LPPME1N11B5FFIAU50000S.

Symptom Possible cause ActionMissingmagnet erroror Alarm output

Float not recognized Confirm that the float is attached

Float is in the dead zone

Raise float to see if the error stops

Wrong number of floats selected

Confirm that the number of floats on the transmitter and the number of floats the transmitter is attempting to verify are the same.

Trigger level error Gain needs to be adjusted

Consult Factory

SE is damaged Consult Factory

Min. trigger level too high

Consult Factory

Volume calculation error

No strap table entered Enter strap table

Level outside range of strap table

Enter additional points in strap table

Strap table incorrect Check value entries

VCF error No VCF table entered Enter VCF table

VCF table incorrect Check VCF value entries

Spare part Part number

Display 254732

Output Housing Part number

HART® Single Loop A, B, C, D, E 254731-1

HART® Dual Loop A, B, C, D, E 254731-2

Modbus A, B, C, D, E 254731-3

DDA A, B, C, D, E 254731-4

HART® Single Loop L 254731-5

HART® Dual Loop L 254731-6

Output Housing Part number

Modbus L 254731-7

DDA L 254731-8

SIL Single Loop A, B, C, D, E 254850-1

SIL Dual Loop A, B, C, D, E 254850-2

SIL Single Loop L 254850-5

SIL Dual Loop L 254850-6


I 19 I

Notified body Protection method Classification StandardC = CEC I = Instrinsic Safety Class I, Division 1, Groups ABCD T4

Class I, Zone 0/1, Ex ia IIC T4Ta = -50°C to 71°C IP65

CAN C22.2 No. 157-92:2012CSA C22.2 No. 1010.1:2004CAN/CSA C22.2 No. 60079-0:2011CAN/CSA C22.2 No. 60079-11:2014CAN/CSA C22.2 No. 60529:2005

F = Explosionproof /Flame proof

Class I, Division 1, Groups BCD T6…T3Ex db IIB+H2 T6…T3 Ga/GbTa = -40°C to 71°C IP65

CSA C22.2 No. 0.4-04:R2013CSA C22.2 No. 0.5:R2012CSA C22.2 No. 0-10:R2015CSA C22.2 No. 30:R2012CAN/CSA C22.2 No. 60079-0:2015CAN/CSA C22.2 No. 60079-1:2016CAN/CSA 622.2 No. 60079-26:2016CAN/CSA C22.2 No. 61010.1:2012CSA C22.2 No. 60529:R2010

E = ATEX I = Instrinsic Safety II 1/2 G Ex ia IIC T4Ta = -50°C to 71°C IP65

EN 60079-0:2012EN 60079-11:2012EN 60529:1991 + A1:2000

F = Flame proof II 1/2 G Ex db IIB+H2 T6…T3 Ga/GbTa = -40°C to 71°C IP65

EN 60079-0:2012+A11:2013EN 60079-1:2014EN 60079-26:2015EN 60529:1991 + A2:2013

F = NEC I = Instrinsic Safety Class I, Division 1, Groups ABCD T4Class I, Zone 0/1, AEx ia IIC T4Ta = -50°C to 71°C IP65

FM 3600:2011FM 3610:2010FM 3810:2005ANSI/ISA 60079-0:2013ANSI/ISA 60079-11:2014ANSI/IEC 60529:2004

F = Explosionproof /Flame proof

Class I, Division 1, Groups ABCD T6…T3Class I, Division 1, Groups BCD T6…T3Class I, Zone 0/1, AEx db IIB+H2 T6…T3 Ga/GbTa = -40°C to 71°C IP65

FM 3600:2011FM 3615:2006FM 3810:2005ANSI/ISA 60079-0:2013ANSI/UL 60079-1:2015ANSI/UL 60079-26:2017ANSI/IEC 60529:2004

I = IEC I = Instrinsic Safety Ex ia IIC T4 Ga/GbTa = -50°C to 71°C IP65

IEC 60079-0:2011IEC 60079-11:2011

F = Flame proof Ex db IIB+H2 T6…T3 Ga/GbTa = -40°C to 71°C IP65

IEC 60079-0:2007-10IEC 60079-1:2007-04IEC 60079-26:2014-10IEC 60529:2013

B = INMETRO I = Instrinsic Safety Ex ia IIC T4 Ga/GbTa = -50°C to 71°C IP65

ABNT NBR IEC 60079-0ABNT NBR IEC 60079-11ABNT NBR IEC 60529

F = Flameproof Ex db IIB+H2 T6…T3 Ga/GbTa = -40°C to 71°C IP65

ABNT NBR IEC 60079-0ABNT NBR IEC 60079-1ABNT NBR IEC 60079-26ABNT NBR IEC 60529

Continued on next page...

13. Agency information

13.1 Approvals overview

The Notified Body is designated in the 13th digit of the model number and the Protection Method is designated in the 14th digit of the model number. These two digits of the model number specify the hazardous area approval that is provided with the selected level transmitter.Shown below are the detailed approval information for the NEC, CEC, IEC, and ATEX approvals. MTS additionally has approvals under INMETRO, NEPSI, KC, CCoE, and CML (Japan). Please contact MTS with any questions about the hazardous approval needed.

Table 6: Agency approvals, part 1


I 20 I

Table 7: Agency approvals, part 2

Notified body Protection method Classification StandardN = NEPSI I = Instrinsic Safety Ex ia IIC T4 Ga/Gb

Ta = -50°C to 71°C IP65GB 3836.1-2010GB 3836.4-2010GB 3836.20-2010


GB 3836.1-2010GB 3836.2-2010

C = CCoE/PESO

I = Instrinsic Safety Ex ia IIC T4 Ga/GbTa = -50°C to 71°C IP65

IEC 60079-0:2011IEC 60079-11:2011Petroleum Rules 2002


IEC 60079-0:2007-10IEC 60079-1:2007-04IEC 60079-26:2014-10IEC 60529:2013Petroleum Rules 2002

T = CML/TIIS I = Instrinsic Safety Ex ia IIC T4 Ga/GbTa = -50°C to 71°C IP65

IEC 60079-0:2011IEC 60079-11:2011


IEC 60079-0:2007-10IEC 60079-1:2007-04IEC 60079-26:2014-10IEC 60529:2013

K = KC I = Instrinsic Safety PENDING PENDINGF = Flameproof PENDING PENDING

13.2 Certificates

Downloadable copies of all certificates are located at www.mtssensors.com and can be downloaded on the product specific landing page. If there is any difficulty in obtaining the certificates from the web contact MTS Technical Support and they will be sent electronically.

13.3 FM

13.3.1 FM IS

13.3.1.1 Specific Conditions of Safe Use

1. When EPL Ga or Da is required, parts of the equipment containing light metals (Aluminum or Titanium) shall be protected from impact so that impact or friction sparks cannot occur, taking into account rare malfunction. Measures to prevent impact or friction sparks when using the equipment containing light metals include but are not limited to• Mounting the probe vertically• No mechanical agitation shall be used• Use of stilling wells to mitigate effect of agitation.• Limit rate of change of level to values such that friction sparks

cannot occur

2. The maximum permitted ambient temperature of the Level Plus Digital/Analog Level Transmitter is 71 °C. To avoid the effects of

process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C

3. Warning: The equipment contains non-metallic enclosure and process parts. To prevent the risk of electrostatic sparking, the non-metallic surface should only be cleaned with a damp cloth. Painted surface of the equipment may store electrostatic charge and become a source of ignition in applications with a low relative humidity <~30% relative humidity where the painted surface is relatively free of surface contamination such as dirt, dust or oil. Cleaning of the painted surface should only be done with a damp cloth.

4. The applicable temperature class, process temperature range and ambient temperature range of the equipment is as follows;• T3 with Process Temperature Range of -40°C to 150°C• T4 with Process Temperature Range of -40°C to 135°C• T5 with Process Temperature Range of -40°C to 100°C• T6 with Process Temperature Range of -40°C to 85°C• Ambient Temperature Range -40°C < Ta < 71°C


I 21 I

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC

FIRST ANGLE 551629-1 B

1 2

DRAWN BY: NJ

A NJ


INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C to +71°C ; IP65when connected in accordance with FM approved installa on drawing # 651543-1

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS

Model No: Serial No: Date :

MTS Systems CorporationSensors Division3001 Sheldon Dr.Cary, NC 27513

Level Plus Transmitter

USE MTS LOGO ARTWORK

10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE

MTS TO PRINTMODEL NO.SERIAL NO.

DATE CODE.

ENTITY PARAMETERS:SEE PRINT REFERENCE CHART

4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

US

LEVEL

1:1

7570 RELEASE TO PRODUCTION

(ACP) LABEL, LP, IS US - DIGITAL

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT INK.

P/N 551629-1 Rev B

10/24/14

86.30 [3.40]

1.78 [.07]

34.69 [1.37]

1.78 [.07]

69.85 [2.75]

R3.30 [.13]

28.70 [1.13]

15.80 [.62]

12/02/14NJB 7847 IP RATING WAS 66

®

Fig. 14: Intrinsically Safe FM label, Modbus, or DDA, NEMA Housing

Fig. 15: Intrinsically Safe FM label, HART®, NEMA Housing

Fig. 16: Intrinsically Safe FM label, Modbus or DDA, Single or Dual Cavity Housing

Fig. 17: Intrinsically Safe FM label, HART®, Single or Dual Cavity Housing

MTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS

INSTALL PER DRAWING # 651544-1/651596-1SUPPLY VOLTAGE: 28 VDC

Level Plus TransmitterR

FM US

APPROVED

P/N 551642-X Rev D


INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS


Level Plus TransmitterR

FMAPPROVED

P/N 551634-X Rev D

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES

0.5 0.1




METRIC

FIRST ANGLE 551629-1 B

1 2

DRAWN BY: NJ

A NJ


INTRINSICALLY SAFECL. I, Div. 1, GR. ABCDCL. I, Zone 0/1, AEx ia IIC T4Ta = -50°C to +71°C ; IP65when connected in accordance with FM approved installa on drawing # 651543-1


Model No: Serial No: Date :



USE MTS LOGO ARTWORK

10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE


DATE CODE.


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

US

LEVEL

1:1


(ACP) LABEL, LP, IS US - DIGITAL

NOTES:1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT INK.

P/N 551629-1 Rev B

10/24/14

86.30 [3.40]

1.78 [.07]

34.69 [1.37]

1.78 [.07]

69.85 [2.75]

R3.30 [.13]

28.70 [1.13]

15.80 [.62]

12/02/14NJB 7847 IP RATING WAS 66

®

651544-1

551641-1

13.3.1.2 Labels


I 22 I

13.3.1.3 Installation drawing

Fig. 18: Intrinsically Safe FM installation drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-1

1 2

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H

C 7898 UPDATED TEMPERATURE ON NOTE 12 TO 71C M

S 2/23/15D 8037 ADDED W

IRING CHART MS 11/3/15

E 8183 ADDED CL I Zone 0/1 MS 8/18/16

F 8256 UPDATED WIRING CHART ON SHEET 2 M

S 1/30/17

H 8818 CHANGED NOTES 14, 16, 17 DR 12-10-19G 8482 UPDATED BEND RADIUS TO 15" M

S 5-17-18

24 VDC

COMM

ON- >

Rx /Tx+

Rx /Tx-

GROUND

EARTH GROUND(SEE NOTE 4)


Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER SAFETY BARRIER

SAFETY BARRIER

NON HAZARDOUS LOCATIONHAZARDOUS LOCATION

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERMINAL

(ACP) INSTALLATIN DWG LP DIGITAL

INTRINSICALLY SAFE FOR US

LEVEL

FM

APPROVED US

N/A

INTRINSICALLY SAFECL. I, DIV. 1, GR. ABCDCL. I Zone 0/1 AEx ia IIC T4 Ta = -50 to 71°C ; IP65

11.INSTALLATIO

N SH

OU

LD BE IN

ACC

OR

DAN

CE W

ITH AN

SI/ISA RP12.06.01

"INSTALLATIO

N O

F INTR

INSIC

ALLY SAFE SYSTEMS FO

R H

AZARD

OU

S (C

LASSIFIED) LO

CATIO

NS" AN

D TH

E NATIO

NAL ELEC

TRIC

AL CO

DE

(ANSI/N

FPA 70). 12.TH

E MAXIM

UM

PERM

ITTED AM

BIENT TEM

PERATU

RE O

F THE LEVEL PLU

S D

IGITAL/AN

ALOG

LEVEL TRAN

SMITTER

IS 71 °C. TO

AVOID

THE EFFEC

TS OF

PRO

CESS TEM

PERATU

RE AN

D O

THER

THER

MAL EFFEC

TS CAR

E SHALL BE

TAKEN TO

ENSU

RE TH

E SUR

RO

UN

DIN

G AM

BIENT AN

D TH

E AMBIEN

T INSID

E TH

E TRAN

SMITTER

HO

USIN

G D

OES N

OT EXC

EED 71°C

13.CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381M

M(15")

14. WH

EN EPL G

A IS REQ

UIR

ED, PAR

TS OF TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T M

ETALS (ALUM

INU

M O

R TITAN

IUM

) SHALL BE PR

OTEC

TED FR

OM

IMPAC

T SO TH

AT IMPAC

T OR

FRIC

TION

SPARKS C

ANN

OT O

CC

UR

, TAKING

INTO

ACC

OU

NT

RAR

E MALFU

NC

TION

. MEASU

RES TO

PREVEN

T IMPAC

T OR

FRIC

TION

SPARKS

WH

EN U

SING

THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS INC

LUD

E BUT AR

E N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

USE O

F STILLING

WELLS TO

MITIG

ATE EFFECT O

F AGITATIO

N.

LIMIT R

ATE OF C

HAN

GE O

F LEVEL TO VALU

ES SUC

H TH

AT FRIC

TION

SPARKS

CAN

NO

T OC

CU

R 15.W

ARN

ING

: SUBSTITU

TION

OF C

OM

PON

ENTS M

AY IMPAIR

INTR

INSIC

SAFETY. 16.W

ARN

ING

: THE EQ

UIPM

ENT C

ON

TAINS N

ON

-METALLIC

ENC

LOSU

RE PAR

TS, TO

PREVEN

T THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE SH

OU

LD O

NLY BE C

LEANED

WITH

A DAM

P CLO

TH. PAIN

TED

SUR

FACE O

F THE EQ

UIPM

ENT M

AY STOR

E ELECTR

OSTATIC

CH

ARG

E AND

BEC

OM

E A SOU

RC

E OF IG

NITIO

N IN

APPLICATIO

NS W

ITH A LO

W R

ELATIVE H

UM

IDITY <~30%

RELATIVE H

UM

IDITY W

HER

E THE PAIN

TED SU

RFAC

E IS R

ELATIVELY FREE O

F SUR

FACE C

ON

TAMIN

ATION

SUC

H AS D

IRT, D

UST O

R

OIL. C

LEANIN

G O

F THE PAIN

TED SU

RFAC

E SHO

ULD

ON

LY BE DO

NE W

ITH A

DAM

P CLO

TH.

17.THE APPLIC

ABLE TEMPER

ATUR

E CLASS, PR

OC

ESS TEMPER

ATUR

E RAN

GE

AND

AMBIEN

T TEMPER

ATUR

E RAN

GE O

F T HE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°C < TA < 71°C

NOTES

1.ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

MEN

TS. SEAL ALL C

ON

DU

ITS WITH

IN 457 M

M(18").

2.LOO

P CABLE M

UST BE 24 AW

G TO

14 AWG

(.511MM

² TO 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IELD. C

ABLE CAPAC

ITANC

E M

UST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER M

). CABLE SH

IELD

IS CO

NN

ECTED

TO SYSTEM

GR

OU

ND

IN N

ON

-HAZAR

DO

US AR

EA. SEE IN

STALLATION

MAN

UAL FO

R AD

DITIO

NAL C

ABLE INFO

RM

ATION

. 3.TH

E RESISTAN

CE BETW

EEN EAR

TH G

RO

UN

D AN

D TH

E INTR

INSIC

ALLY SAFE G

RO

UN

D M

UST BE LESS TH

AN 1 O

HM

. 4.TH

E TRAN

SDU

CER

FRAM

E SHALL BE G

RO

UN

DED

TO EAR

TH G

RO

UN

D D

IREC

TLY OR

THR

OU

GH

THE EQ

UIPM

ENT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQU

IPMEN

T CO

NN

ECTED

TO ASSO

CIATED

APPARATU

S MU

ST N

OT U

SE OR

GEN

ERATE M

OR

E THAN

250 VRM

S OR

VDC

6.AS SOC

IATED APPAR

ATUS M

ANU

FACTU

RER

'S INSTALLATIO

N D

RAW

ING

MU

ST BE FOLLO

WED

WH

EN IN

STALLING

THIS EQ

UIPM

ENT.

7.ON

LY USE N

EC (E.G

FM) APPR

OVED

BARR

IERS.

8.ENTITY PAR

AMETER

S: SU

PPLY: RX/TX-: R

X/TX+: U

i = 28VDC

Ui= 8.6V U

i= 8.6V Ii = 100M

A Ii = 10MA Ii = 10M

A C

i = 0 µF Ci = 0 µF C

i = 0 µF Li = 0 µH

Li = 0 µH Li = 0 µH

Pi = 0.7 W Pi= 0.0215 W

Pi= 0.0 215 W 9.TH

E ENTITY C

ON

CEPT ALLO

WS IN

TERC

ON

NEC

TION

OF IN

TRIN

SICALLY SAFE

APPARATU

S WITH

ASSOC

IATED APPAR

ATUS W

HEN

THE FO

LLOW

ING

IS TRU

E: Vm

ax OR

Ui ≥ Voc, VT O

R U

o; Im

ax OR

Ii ≥ Isc, It OR

Io; Pm

ax OR

Pi ≥ Po; C

a ≥ Ci + C

cable; La ≥ Li + Lcable. 10.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E OF H

OU SIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D).


I 23 I

Fig. 19: Intrinsically Safe FM installation drawing, Modbus and DDA, Page 2

DETAIL ASCALE 1.60 : 1

DETAIL CSCALE 3 : 1

DETAIL DSCALE 1.2

DETAIL ESCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-1

2 2

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18

+24V GNDEARTHTX/RX+TX/RX-

GND+24V

TX/RX-TX/RX+EARTH

GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

457 MM

(18") OF H

OU

SING

.



+24V GND EARTH Tx/Rx+ Tx/Rx-

WIRE COLOR

SIGNALRED

24 V PWR

BLACK 0 V PW

RBLUE

N/AW

HITERX TX +

GREENRX TX -

DRAIN WIRE

EARTH GROUND

WIRING CHART (FOR NEM

A GAUGE)

PIN #SIGNAL

PIN 124 V PW

RPIN 2

0 V PWR

PIN 3N/A

PIN 4RX TX+

PIN 5RX TX-

PIN 6EARTH GROUND

PIN WIRING CHART (FOR NEM

A GAUGE)

LEVEL


I 24 I

Fig. 20: Intrinsically Safe FM installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-1LEVEL

1 2

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18

NO

N H

AZARD

OU

S LOC

ATION

HAZAR

DO

US LO

CATIO

N

1. ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE M

TS LP SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

SEAL ALL CO

ND

UITS W

ITHIN

457 MM

(18"). 2. LO

OP C

ABLE MU

ST BE 24 AWG

TO 14 AW

G (.511M

M² to 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IELD. C

ABLE CAPAC

ITANC

E MU

ST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER m

). CABLE SH

IELD IS C

ON

NEC

TED TO

SYSTEM G

RO

UN

D IN

NO

N-H

AZARD

OU

S AREA. SEE IN

STALLATION

MAN

UAL

FOR

ADD

ITION

AL CABLE IN

FOR

MATIO

N.

3. THE R

ESISTANC

E BETWEEN

EARTH

GR

OU

ND

AND

THE IN

TRIN

SICALLY SAFE G

RO

UN

D M

UST BE LESS TH

AN 1 O

HM

. 4. TH

E TRAN

SDU

CER

FRAM

E SHALL BE G

RO

UN

DED

TO EAR

TH G

RO

UN

D D

IREC

TLY OR

THR

OU

GH

THE EQ

UIPM

ENT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQU

IPMEN

T CO

NN

ECTED

TO ASSO

CIATED

APPARATU

S MU

ST N

OT U

SE OR

GEN

ERATE M

OR

E THAN

250 VRM

S OR

VDC.

6. ASSOC

IATED APPAR

ATUS M

ANU

FACTU

RER

'S INSTALLATIO

N D

RAW

ING

MU

ST BE FO

LLOW

ED W

HEN

INSTALLIN

G TH

IS EQU

IPMEN

T 7. O

NLY U

SE NEC

(e.g FM) APPR

OVED

BARR

IERS.

8. APPRO

VED LO

OP SEPAR

ATION

METH

OD

S: *R

UN

LOO

PS IN SEPAR

ATE CABLES

*RU

N LO

OPS IN

SEPARATE G

RO

UN

DED

SHIELD

S 9. EN

TITY PARAM

ETERS EAC

H LO

OP:

Ui = 28 VD

C Ii = 120 m

A C

i = 0 µF Li = 5 µH Pi = 840 m

W 10. D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E OF

HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D)

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

24 VDC

CO

NTR

OL

INPU

T 1

CO

NTR

OL

INPU

T 2

APPRO

VED SAFETY

BARR

IER

APPRO

VED SAFETY

BARR

IER

LOO

P VOLTAG

E

SHIELD

SHIELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

FM

APPROVED US

US

(ACP) INSTALLATIN DWG LP ANALOG


SING

LE OR

DU

AL CAVITY

NEM

A HO

USIN

G

INTRINSICALLY SAFECL. I, DIV. 1, GR. ABCDCL. I Zone 0/1 AEx ia IIC T4 Ta = -50 to 71°C ; IP65

EARTH

GR

OU

ND

(SEE NO

TE 4)

EARTH

GR

OU

ND

(SEE NO

TE 4)

11 INSTALLATIO

N SH

OU

LD BE IN

ACC

OR

DAN

CE W

ITH AN

SI/ISA RP12.06.01

"INSTALLATIO

N O

F INTR

INSIC

ALLY SAFE SYSTEMS FO

R H

AZARD

OU

S (CLASSIFIED

) LO

CATIO

NS" AN

D TH

E NATIO

NAL ELEC

TRIC

AL CO

DE (AN

SI/NFPA 70).

12.THE M

AXIMU

M PER

MITTED

AMBIEN

T TEMPER

ATUR

E OF TH

E LEVEL PLUS

DIG

ITAL/ANALO

G LEVEL TR

ANSM

ITTER IS 71 °C

. TO AVO

ID TH

E EFFECTS O

F PRO

CESS

TEMPER

ATUR

E AND

OTH

ER TH

ERM

AL EFFECTS C

ARE SH

ALL BE TAKEN TO

ENSU

RE

THE SU

RR

OU

ND

ING

AMBIEN

T AND

THE AM

BIENT IN

SIDE TH

E TRAN

SMITTER

HO

USIN

G

DO

ES NO

T EXCEED

71°C 13.C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381MM

(15") 14. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G

LIGH

T METALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PRO

TECTED

FRO

M IM

PACT

SO TH

AT IMPAC

T OR

FRIC

TION

SPARKS C

ANN

OT O

CC

UR

, TAKING

INTO

AC

CO

UN

T RAR

E MALFU

NC

TION

. MEASU

RES TO

PREVEN

T IMPAC

T OR

FR

ICTIO

N SPAR

KS WH

EN U

SING

THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS IN

CLU

DE BU

T ARE N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N

SPARKS C

ANN

OT O

CC

UR

15.WAR

NIN

G: SU

BSTITUTIO

N O

F CO

MPO

NEN

TS MAY IM

PAIR IN

TRIN

SIC

SAFETY. 16.W

ARN

ING

: THE EQ

UIPM

ENT C

ON

TAINS N

ON

-METALLIC

ENC

LOSU

RE PAR

TS, TO

PREVEN

T THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SU

RFAC

E SHO

ULD

ON

LY BE CLEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED

SU

RFAC

E OF TH

E EQU

IPMEN

T MAY STO

RE ELEC

TRO

STATIC C

HAR

GE AN

D

BECO

ME A SO

UR

CE O

F IGN

ITION

IN APPLIC

ATION

S WITH

A LOW

RELATIVE

HU

MID

ITY <~30% R

ELATIVE HU

MID

ITY WH

ERE TH

E PAINTED

SUR

FACE IS

RELATIVELY FR

EE OF SU

RFAC

E CO

NTAM

INATIO

N SU

CH

AS DIR

T, DU

ST OR

OIL.

CLEAN

ING

OF TH

E PAINTED

SUR

FACE SH

OU

LD O

NLY BE D

ON

E WITH

A DAM

P C

LOTH

. 17.TH

E APPLICABLE TEM

PERATU

RE C

LASS, PRO

CESS TEM

PERATU

RE R

ANG

E AN

D AM

BIENT TEM

PERATU

RE R

ANG

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C

< TA < 71°C

NOTES


I 25 I

Fig. 21: Intrinsically Safe FM installation drawing, HART®, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

DETAIL H

SCALE 1 : 1

D

E

F

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-1LEVEL

2 2

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

457 MM

(18") OF H

OU

SING

.

FIGU

RE 2

DU

AL CAVITY H

OU

SING

LOOP 1+ LOOP 1- EARTH LOOP 2+ LOOP 2-

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING


(ACP) IN

STALLATION

DW

G LP AN

ALGO

IN

TRIN

SICALLY SAFE ATEX/IEC

E


PIN #SIGNAL

PIN 1LOOP 1-

PIN 2LOOP 1+

PIN 3LOOP 2-

PIN 4LOOP 2+

PIN 5N/A

PIN 6EARTH GROUND

WIRE COLOR

SIGNALRED

LOOP 1+BLACK

LOOP 1-BLUE

LOOP 2-W

HITELOOP 2+

GREENN/A

DRAIN WIRE

EARTH GROUND


A GAUGE)

WIRING CHART(FOR NEM

A GAUGE)


I 26 I

13.3.2 FM XP



2. Cables shall be rated > 5°C above maximum ambient temperature.

3. To maintain the ingress protection rating of IP65, Teflon tape (3 wraps) or pipe dope shall be used. Refer to Installation Instructions.

4. The equipment can be installed in the boundary wall between a Zone 0 area and the less hazardous area, Zone 1. In this configuration, the process connection is installed in a Zone 0 area, while the transmitter housing is installed in a Zone 1 area. Refer to installation instructions.

5. Flexible gauges have a minimum bend diameter of 381mm (15 inches).

6. Flamepaths not for repair. 7. The applicable temperature class, process temperature range and

ambient temperature range of the equipment is as follows;• T3 with Process Temperature Range of -40°C to 150°C• T4 with Process Temperature Range of -40°C to 135°C• T5 with Process Temperature Range of -40°C to 100°C• T6 with Process Temperature Range of -40°C to 85°C• Ambient Temperature Range -40°C < Ta < 71°C

8. When mounting on a MLG (magnetic level gauge) make sure the electronic head and pressure barrier have a minimum spacing of 5 inches. See Installation Manual for detail.

9. When EPL Ga or Da is required, parts of the equipment containing light metals (Aluminum or Titanium) shall be protected from impact so that impact or friction sparks cannot occur, taking into account rare malfunction. Measures to prevent impact or friction sparks when using the equipment containing light metals include but are not limited to:• Mounting the probe vertically• No mechanical agitation shall be used• Use of stilling wells to mitigate effect of agitation.• Limit rate of change of level to values such that friction sparks

cannot occur



FM16US0242X

EXPLOSION PROOF FOR CL. I, DIV. 1, GR. BCD T6...T3CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: RS485 WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSUR

INSTALL PER # 651552-1/651595-1MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)

FM US

APPROVED

P/N 551474- Rev B

R

!

Fig. 22: Explosion proof, FM label, Modbus or DDA Housing Option G, H, or L

Fig. 23: Explosion proof, FM label, Modbus or DDA, Housing Option D, E

Fig. 24: Explosion proof, FM label, HART®, Housing Option G, H, or L

Fig. 25: Explosion proof, FM label, HART®, Housing Option D, E



FM16US0242X

EXPLOSION PROOF FOR CL. I, DIV. 1, GR. ABCD T6...T3CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: RS485 WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSUR


FM US

APPROVED

P/N 551474- Rev B

R

!

Level Plus TransmitterFM16US0242X


EXPLOSION PROOF FOR CL. I, DIV. 1, GR. BCD T6...T3CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: 4-20mA WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE PRESENT FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSUR


FM USAPPROVED

P/N 551495-Rev B

R

!

Level Plus TransmitterFM16US0242X


EXPLOSION PROOF FOR CL. I, DIV. 1, GR. ABCD T6...T3CL. I, ZONE 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C TO +71°C ; IP 65INPUT: 28V (120mA) maxOUTPUT: 4-20mA WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE PRESENT FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSUR


FM USAPPROVED

P/N 551495-Rev B

R

!

13.3.2.2 Labels


I 27 I

13.3.2.3 Installation Drawing

Fig. 26: Explosion proof, FM Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-1C

LEVEL1

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***C 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19B 8482 UPDATED W

IRING DWG TO ANALOG M

S 5/17/18 A 7957 RELEASED TO PRODUCTION M

S 10/22/15

EARTH GROUND

LOOP 2-

LOOP 2+

EARTH GROUND

LOOP 1-

LOOP 1+

ZONE 1

ZONE 0SEE NOTE 8

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

FM

APPROVED US


EXPLOSION PROOF US

SING

LE OR

DU

AL CAVITY

FM US- FM

16US0242XEXPLOSION PROOFCL. I, DIV. 1, GR. ABCD T6...T3CL. I, DIV. 1, GR. BCD T6...T3CL. 1, ZN. 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C ; IP65

HAZARDOUS LOCATIONNON HAZARDOUS LOCATION

CO

ND

UIT SEAL

CO

ND

UIT

SEE NO

TE 1

CO

ND

UIT SEAL

5" [127mm

] Minim

um

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m (2") O

F THE

ENC

LOSU

RE. FO

R D

IVISION

INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 457m

m (18") O

F THE EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PREVEN

T IGN

ITION

OF FLAM

MABLE O

R C

OM

BUSTIBLE ATM

OSPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED SURFACE OF THE EQUIPMENT M

AY STORE ELECTROSTATIC CHARGE AND BECOM

E A SOURCE OF IGNITION IN APPLICATIONS WITH A LOW

RELATIVE HUMIDITY <~30%

RELATIVE HUM

IDITY WHERE THE PAINTED SURFACE IS RELATIVELY FREE OF SURFACE CONTAM

INATION SUCH AS DIRT, DUST OR OIL. CLEANING OF THE PAINTED SURFACE SHOULD ONLY BE DONE W

ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE INSTALLED

IN TH

E BOU

ND

ARY W

ALL BETWEEN

A ZON

E 0 AREA AN

D TH

E LESS H

AZARD

OU

S AREA, ZO

NE 1. IN

THIS C

ON

FIGU

RATIO

N, TH

E PRO

CESS C

ON

NEC

TION

IS INSTALLED

IN

A ZON

E 0 AREA, W

HILE TH

E TRAN

SMITTER

HO

USIN

G IS IN

STALLED IN

A ZON

E 1 AREA.

9. THE APPLIC

ABLE TEMPER

ATUR

E CLASS O

F THE EQ

UIPM

ENT, AM

BIENT TEM

PERATU

RE R

ANG

E, AN

D M

AXIMU

M PR

OC

ESS TEMPER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AGN

ETIC LEVEL G

AUG

E MAKE SU

RE TH

E ELECTR

ON

IC H

EAD AN

D PR

ESSUR

E BAR

RIER

HAVE A M

INIM

UM

SPACIN

G O

F 5 INC

HES. SEE IN

STALLATION

MAN

UAL FO

R D

ETAIL11. FLAM

EPATHS AR

E NO

T FOR

REPAIR

12. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS (ALUM

INU

M O

R TITAN

IUM

) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO

ACC

OU

NT R

ARE M

ALFUN

CTIO

N. M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS WH

EN U

SING

THE

EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R


I 28 I

Fig. 27: Explosion proof, FM Installation Drawing, Modbus and DDA, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-1C

LEVEL2

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***C 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19B 8482 UPDATED W

IRING DWG TO ANALOG M

S 5/17/18 A 7957 RELEASED TO PRODUCTION M

S 10/22/15

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: FO

R ZO

NE IN

STALLATION

S, A SEAL SHALL BE IN

STALLED W

ITHIN

50mm

(2") OF TH

E EN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


STALLED W

ITHIN

457mm

(18") OF TH

E ENC

LOSU

RE.

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY H

OU

SING

(ACP) IN

STALLATION

DW

G LP AN

ALOG

IN

TRIN

SICALLY SAFE U

S



I 29 I

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-1B

1

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***B 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19A 7957 RELEASED TO PRODUCTION M

S 6/22/16

24 VDC

COMM

ON-

Rx /Tx+

Rx /Tx-

EARTH GROUND

EARTH GROUND

ZONE 1

ZONE 0SEE NOTE 8


AGEN

CY C

ON

TRO

LLED D

RAW

ING

(US). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERMINAL

(ACP) INSTALLATION DWG LP DIGITAL

EXPLOSION PROOF US

LEVEL

FM

APPROVED

N/A

EXPLOSION PROOFCL. I, DIV. 1, GR. ABCD T6...T3CL. I, DIV. 1, GR. BCD T6...T3CL. 1, ZN. 0/1, AEx db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C ; IP65

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m O

F THE

ENC

LOSU

RE. FO

R D

IVISION

INSTALLA

TION


STALLED W

ITHIN

457mm

(18") OF TH

E ENC

LOSU

RE.

2.DU

AL-CAVITY EN

CLO

SUR

ES: C

USTO

MER

CO

NN

ECTIO

NS W

ILL BE MAD

E AT TERM

INAL BLO

CK O

N PO

WER

SIDE

OF H

OU

SING

(NO

T TO TER

MIN

AL BLOC

K ON

INTER

CO

NN

ECT BO

ARD

). SEE FIGU

RE 2 O

N PAG

E 23. C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381mm

(15")4.W

ARN

ING

: TO PR

EVENT IG

NITIO

N O

F FLAMM

ABLE OR

CO

MBU

STIBLE ATMO

SPHER

ES, D

ISCO

NN

ECT PO

WER

BEFOR

E SERVIC

ING

5.W

ARN

ING

: THE EQ

UIPM

ENT C

ON

TAINS N

ON

-METALLIC

ENC

LOSU

RE AN

D PR

OC

ESS PARTS, TO

PREVEN

T TH

E RISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC SU

RFAC

E AND

PRO

CESS PAR

TS SHO

ULD

ON

LY BE C

LEANED

WITH

A DAM

P CLO

TH. PAINTED SURFACE OF THE EQUIPM

ENT MAY STORE ELECTROSTATIC CHARGE

AND BECOME A SOURCE OF IGNITION IN APPLICATIONS W

ITH A LOW RELATIVE HUM

IDITY <~30% RELATIVE

HUMIDITY W

HERE THE PAINTED SURFACE IS RELATIVELY FREE OF SURFACE CONTAMINATION

SUCH AS DIRT, DUST OR OIL. CLEANING OF THE PAINTED SURFACE SHOULD ONLY BE DONE W

ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE INSTALLED

IN TH

E BOU

ND

ARY W

ALL BETWEEN

A ZON

E 0 AREA AN

D TH

E LESS H

AZARD

OU

S AREA, ZO

NE 1. IN

THIS C

ON

FIGU

RATIO

N, TH

E PRO

CESS C

ON

NEC

TION

IS INSTALLED

IN

A ZON

E 0 AREA, W

HILE TH

E TRAN

SMITTER

HO

USIN

G IS IN

STALLED IN

A ZON

E 1 AREA.

9. THE APPLIC

ABLE TEMPER

ATUR

E CLASS O

F THE EQ

UIPM

ENT, AM

BIENT TEM

PERATU

RE R

ANG

E, AN

D M

AXIMU

M PR

OC

ESS TEMPER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C

Ta+71°C10. W

HEN

MO

UN

TING

ON

A MAG

NETIC

LEVEL GAU

GE M

AKE SUR

E THE ELEC

TRO

NIC

HEAD

AND

PRESSU

RE

BARR

IER H

AVE A MIN

IMU

M SPAC

ING

OF 5 IN

CH

ES. SEE INSTALLATIO

N M

ANU

AL FOR

DETAIL

11. FLAMEPATH

S ARE N

OT FO

R R

EPAIR

12. WH

EN EPL G

a IS REQ

UIR

ED, PAR

TS OF TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PR

OTEC

TED FR

OM

IMPAC

T SO TH

AT IMPAC

T OR

FRIC

TION

SPARKS C

ANN

OT O

CC

UR

, TAKING

INTO

ACC

OU

NT R

ARE M

ALFUN

CTIO

N.

MEASU

RES TO

PREVEN

T IMPAC

T OR

FRIC

TION

SPARKS W

HEN

USIN

G TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE

NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R

FM US- FM

16US0242X

CONDUIT SEAL

CONDUIT

SEE NOTE 1

CONDUIT SEAL

5" [127mm

] Minim

um

Fig. 28: Explosion proof, FM Installation Drawing, HART®, Page 1


I 30 I

DETAIL FSCALE 1.60 : 1

DETAIL GSCALE 3 : 1

DETAIL HSCALE 1.2

F

G

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-1B

2

2 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***B 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19A 7957 RELEASED TO PRODUCTION M

S 6/22/16


GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: FO

R ZO

NE IN

STALLATION


STALLED W

ITHIN

50mm

(2") OF TH

EEN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


STALLED W

ITHIN

457mm

(18") OF TH

E ENC

LOSU

RE.


EXPLOSION PROOF U.S.A


Fig. 29: Explosion proof, FM Installation Drawing, HART®, Page 2


I 31 I

13.4 FMC

13.4.1 FMC IS

13.4.1.1 Specific conditions of safe use


cannot occur

2. The maximum permitted ambient temperature of the Level Plus Digital/Analog Level Transmitter is 71 °C. To avoid the effects of process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C




I 32 I

Fig. 30: Intrinsically Safe FMC label, Modbus and DDA, NEMA Housing

1

1

2

2

A A

B B


TITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METRIC

FIRST ANGLE 551629-2 D

LEVEL1 2

(ACP) LABEL, LP, IS CANADA-DIGITAL

DRAWN BY: NJ


C 8037 ADDED FRENCH TRANSLATION DR 10/12/15B 7847 IP RATING WAS 66 NJ 12/02/14

1:1

D 8183 ADDED CL I, ZONE0/1 MS 8/18/16

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCD CL.I, ZONE 0/1, Ex ia IIC T4 Ta = -50°C to +71°C ; IP66

when connected in accordance with FM approved installation drawing # 651543-2lorsqu'il est connecté en conformité avec FM approuvé le plan d'installation # 651543-2

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGSAVERTISSEMENT : se référer au schéma d'installation à la prudence / AVERTISSEMENTS


Model No: Modèle No:

Serial No:Numéro de série:

Date:

R

8 POINT TEXT SIZE


DATE CODE.


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

C


NOTES:

1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.

2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.

3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT

P/N: 551629-2 Rev D

®

Fig. 31: Intrinsically Safe FMC label, HART®, NEMA Housing

Fig. 32: Intrinsically Safe FMC label, Modbus and DDA, Single and Dual Cavity Housing

Fig. 33: Intrinsically Safe FMC label, HART®, Single and Dual Cavity Housing

1

1

2

2

A A

B B

ECO # DESCRIPTION

C 8037 ADDED FRENCH TRANSLATION DR 10/12/15


(ACP) LABEL, LP, IS CANADA-ANALOGMTS SYSTEMS CORPORATIONSENSORS DIVISION3001 SHELDON DRIVE, CARY, NC 27513

B 7847 IP RATING WAS 66 NJ 12/02/14

PRODUCT LINE

FIRST ANGLE

mANGLES

SIZE

LEVEL1:1 METRICSCALE:

DRAWN BY:

DWG NO.

1

DATEBY

2OF

D551641-2REV

SHEET


1 PLACEMM

0.1

0 PLACESMM

0.5

THE INFORMATION AND DESIGN(S) DISCLOSEDHEREIN ARE THE PROPERTY OF MTS SYSTEMSCORPORATION AND MAY NOT BE USED,REPRODUCED OR DISCLOSED IN ANY FORMEXCEPT AS GRANTED IN WRITING BY MTSSYSTEMS CORPORATION. THIS RESTRICTIONEXCLUDES INFORMATION THAT IS IN THE PUBLIC DOMAIN OR WAS LEGITIMATELY IN THEPRIOR POSSESSION OF THE RECIPIENT.

PROPRIETARY DATA TOLERANCESUNLESS OTHERWISE SPECIFIED TITLE

REV

D 8183 ADDED CL. I Zone 0/1 MS 8/8/16

WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGSAVERTISSEMENT : se référer au schéma d'installation à la prudence / AVERTISSEMENTS

INTRINSICALLY SAFECL. I, Div. 1, GR. ABCD CL.I Zone 0/1 Ex ia IIC T4 Ta = -50°C to +71°C ; IP65

when connected in accordance with FM approvedinstallation drawing # 651544-2 lorsqu'il est connecté en conformité avec FM approuvéedessin d'installation # 651544-2


Model No: Modèle No:

Serial No:Numéro de série:

Date:

R

USE MTS LOGOARTWORK

10 POINT SIZE

8 POINT TEXT SIZE

4.5 POINT TEXT SIZE

MTS TO PRINTMODEL NO.SERIAL NO.DATE CODE


4.5 POINT TEXT SIZE

FM APPROVED

USE FM LOGO ARTWORK

C


P/N: 551641-2 Rev D

NOTES:

1. STANDARD LETTERING UNIVERS 55 OR ITC GARAMOND BOOK.

2. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.

3. MATERIAL: 3M 7883 METALLIZED POLYESTER FOIL W/GAS RESISTANT INK.

1.78 [.07]

1.78 [.07]

28.70 [1.13]

15.80 [.62]

34.69 [1.37]

86.30 [3.40]

69.85 [2.75]

R3.30 [.13]

®

MTS Systems Corp. Sensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFE: CL. I, Div. 1, GR. ABCD, CL.I Zone 0/1 Ex ia IIC T4Ta = -50°C TO +71°C ; IP65

REFER TO INSTALLATION DWG #651544-2/651596-2 FOR CAUTION/WARNINGS WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY Avertissement : Se référer au document DWG # 651544-2/651596-2 précautions d'installations ATTENTION : La substitution de composants peut compromettre la sécurité intrinsèque

LPXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX-XX

R

FM CAPPROVED


P/N 551704-X Rev F

MTS Systems Corp. Sensors Division3001 Sheldon Drive, Cary, N.C. 27513

INTRINSICALLY SAFE: CL. I, Div. 1, GR. ABCD, CL. I Zone 0/1 Ex ia IIC T4 Ta = -50°C TO +71°C ; IP65

REFER TO INSTALLATION DWG #651543-2/651594-2 FOR CAUTION/WARNINGS WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY Avertissement : Se référer au document DWG # 651543-2/651594-2 précautions d'installations ATTENTION : La substitution de composants peut compromettre la sécurité intrinsèque

LPXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX-XX

R

FM CAPPROVED


P/N 551702-X Rev F

13.4.1.2 Labels


I 33 I

13.4.1.3 Installation Drawing

Fig. 34: Intrinsically Safe FMC installation drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-2

1 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18

24 VDC

COMM

ON- >

Rx/Tx+

Rx /Tx-

GROUND

EARTH GROUND(SEE NOTE 4) TERRE( Voir note 4 )


Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER Barrière de sécurité



NON HAZARDOUS LOCATION NON ZONE DANGEREUSE

HAZARDOUS LOCATION ZONE DANGEREUSE

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(CAN

ADA). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

AGEN

CE D

ESSIN contrôlée ( C

ANAD

A ) . AUC

UN

CH

ANG

EMEN

T sans l'accord préalable AGEN

CE APPR

OBATIO

N

EARTH TERMINAL

BORNE DE TERRE


INTRINSICALLY SAFE FOR CANADA

LEVEL

FM

APPROVED

C

N/A

INTRINSICALLY SAFE (INTRINSÈQUEMENT SÛR)

CL. I, DIV. 1, GR. ABCDCL. I Zone 0/1 Ex ia IIC T4 Ta = -50 to 71°C ; IP65

1.ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

MEN

TS. SEAL ALL C

ON

DU

ITS WITH

IN 457 M

M(18").

2.LOO

P CABLE M

UST BE 24 AW

G TO

14 AWG

(.511MM

² TO 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IEL D. C

ABLE CAPAC

ITANC

E M

UST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER M

). CABLE SH

IELD

IS CO

NN

ECTED

TO SYSTEM

GR

OU

ND

IN N

ON

-HAZAR

DO

US AR

EA. SEE IN

STALLATION

MAN

UAL FO

R AD

DITIO

NAL C

ABLE INFO

RM

ATION

. 3.TH

E RESISTAN

CE BETW

EEN EAR

TH G

RO

UN

D AN

D TH

E INTR

INSIC

ALLY SAFE G

RO

UN

D M

UST BE LESS TH

AN 1 O

HM

. 4.TH

E TRAN

SDU

CER

FRAM

E SHALL BE G

RO

UN

DED

TO EAR

TH G

RO

UN

D D

IREC

TLY OR

THR

OU

GH

THE EQ

UIPM

ENT O

N W

HIC H

IT IS MO

UN

TED.

5. CO

NTR

OL EQ

UIPM

ENT C

ON

NEC

TED TO

ASSOC

IATED APPAR

ATUS M

UST

NO

T USE O

R G

ENER

ATE MO

RE TH

AN 250 VR

MS O

R VD

C 6.ASSO

CIATED

APPARATU

S MAN

UFAC

TUR

ER'S IN

STALLATION

DR

AWIN

G M

UST BE FO

LLOW

ED W

HEN

INSTALLIN

G TH

IS EQU

IPMEN

T. 7.O

NLY U

SE CEC

APPRO

VED BAR

RIER

S. 8.EN

TITY PARAM

ETERS:

SU

PPLY: RX/TX-: R

X/TX+: U i = 28VD

C U

i= 8.6V Ui= 8.6V

Ii = 100MA Ii = 10M

A Ii = 10MA

Ci = 0 µF C

i = 0 µF Ci = 0 µF


Li = 0 µH Pi = 0.7 W

Pi= 0.0215 W Pi= 0.0215 W

9.THE EN

TITY CO

NC

EPT ALLOW

S INTER

CO

NN

ECTIO

N O

F INTR

INSIC

ALLY SAFE APPAR

ATUS W

ITH ASSO

CIATED

APPARATU

S WH

EN TH

E FOLLO

WIN

G IS TR

UE:

Vm

ax OR

Ui ≥ Voc, VT O

R U

o; Im

ax OR

Ii ≥ Isc, It OR

Io; Pm

ax OR

Pi ≥ Po; C

a ≥ Ci + C


UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E OF H

OU

SING

(NO

T TO TER

MIN

AL BLOC

K ON

INTER

CO

NN

ECT BO

ARD

).

NOTES: (FO

R NOTES IN FRENCH SEE PAG

E 3, NOTES PO

UR VOIR EN FRANÇAIS PAG

E 3)

11.FOR

INSTALLATIO

N W

ITHIN

CAN

ADA SEE, C

ANAD

IAN ELEC

TRIC

AL CO

DE,

CSA N

o. C22.1.

12.THE M

AXIMU

M PER

MITTED

AMBIEN

T TEMPER

ATUR

E OF TH

E LEVEL PLUS

DIG

ITAL/ANALO

G LEVEL TR

ANSM

ITTER IS 71 °C

. TO AVO

ID TH

E EFFECTS

OF PR

OC

ESS TEMPER

ATUR

E AND

OTH

ER TH

ERM

AL EFFECTS C

ARE SH

ALL BE TAKEN

TO EN

SUR

E THE SU

RR

OU

ND

ING

AMBIEN

T AND

THE AM

BIENT

INSID

E THE TR

ANSM

ITTER H

OU

SING

DO

ES NO

T EXCEED

71°C 13. C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381MM

(15") 14. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT

MET ALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO AC

CO

UN

T R

ARE M

ALFUN

CTIO

N. M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS W

HEN

USIN

G TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE

NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS C

ANN

OT O

CC

UR

15.WAR

NIN

G: SU

BSTITUTIO

N O

F CO

MPO

NEN

TS MAY IM

PAIR IN

TRIN

SIC SAFETY.

16.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E PARTS,

TO PR

EVENT TH

E RISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC SU

RFAC

E SHO

ULD

ON

LY BE CLEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED

SU

RFAC

E OF TH

E EQU

IPMEN

T MAY STO

RE ELEC

TRO

STATIC C

HAR

GE AN

D

BECO

ME A SO

UR

CE O

F IGN

ITION

IN APPLIC

ATION

S WITH

A LOW

RELATIVE

HU

MID

ITY <~30% R

ELATIVE HU

MID

ITY WH

ERE TH

E PAINTED

SUR

FACE IS

RELATIVELY FR

EE OF SU

RFAC

E CO

NTAM

INATIO

N SU

CH

AS DIR

T, DU

ST OR

O

IL. CLEAN

ING

OF TH

E PAINTED

SUR

FACE SH

OU

LD O

NLY BE D

ON

E WITH

A D

AMP C

LOTH

. 17.TH

E APPLICABLE TEM

PERATU

RE C

LASS, PRO

CESS TEM

PERATU

RE R

ANG

E AN

D AM

BIEN T TEMPER

ATUR

E RAN

GE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°C < TA < 71°C


I 34 I



DETAIL CSCALE 3 : 1

DETAIL DSCALE 1.2

DETAIL ESCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-2

2 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18


GND+24V

TX/RX-TX/RX+EARTH

GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

(Seule cavité & NEM

A LOG

EMEN

T)FIG

UR

E 2D

UAL C

AVITY HO

USIN

G(C

avité double LOG

EMEN

T)

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM Le client doit relier la m

asse LUG

à l'extérieur pour le système au sol SÉC

UR

ITÉ DE TER

RE

WAR

NIN

G:

CO

ND

UIT SEALS R

EQU

IRED

WITH

IN 457 M

M (18") O

F HO

USIN

G.

Étanchéité des conduits requis dans les 457 mm

( 18 " ) DU

LOG

EMEN

T





A GAGUE)


A GAUGE)

LEVEL

WIRE COLOR

SIGNALRED

24 V PWR

BLACK 0 V PW

RBLUE

N/AW

HITERX TX +

GREENRX TX -

DRAIN WIRE

EARTH GROUND

PIN #SIGNAL

PIN 124 V PW

RPIN 2

0 V PWR

PIN 3N/A

PIN 4RX TX+

PIN 5RX TX-

PIN 6EARTH GROUND


I 35 I


11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-2

3 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

H


S 2/23/15D 8037 ADDED W




S 1/30/17


S 5-17-18

NO

TES:1. La réglem

entation doit être respectée suivant les codes locaux et nationaux LO

RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X.Sceller tous les conduits à m

oins de 457 mm

(18"). 2. Boucle de câble doit être de 24 AW

G à 14 AW

G (.511M

M2 à 1.6M

M2)

Paire Torsadée Blindée avec le bouclier. La capacité du câble devraÊtre inférieure à 30 pF PAR

PIED (98 pF PAR

M). Le blindage du câble est raccordé

À la terre EN ZO

NE N

ON

DAN

GER

EUSE. VO

IR m

anuel d'installationIN

FOR

MATIO

NS de câble supplém

entaire. 3. La résistance entre la TER

RE ET la zone IN

TRIN

SEQU

ED

oit être inférieure à 1 ohm.

4. Le boîtier du capteur doit être relié à la TERR

E directement ou par

L'équipement sur lequel il est m

onté. 5. Equipem

ent de comm

an de relié à l'appareil associé ne doit pas utiliser ou générer plus de 250 VRM

S OU

VDC

6 Le plan d'installation associé du fabricant de l'appareil doit être suivi lors de l'installation de cet équipement

7. UTILISER

UN

IQU

EMEN

T DES BAR

RIER

ES APPRO

UVÉES C

EC.

8. PARAM

ÈTRES :

SUPPLY: R

x/Tx- : Rx/Tx+ :

Ui = 28VD

C U

i= 8.6V Ui= 8.6V

Ii = 100mA Ii = 10m

A Ii = 10mA

Ci = 0 µF C

i = 0 µF Ci = 0 µF

Li = 0 µH Li = 0 µH Li = 0 µH

Pi = 0.7 W Pi= 0.0215 W

Pi= 0.0215 W 9. Le concept de l'entité perm

et l'interconnexion de l'appareil de sécurité intrinsèque avec un appareil associé lorsque la suivante est vraie :Vm

ax or Ui > Voc, Vt or U

o;Im

ax or Ii > Isc, It or Io;Pm

ax or Pi > Po;C

a > Ci + C

cable;La > Li + Lcable. 10. EN

CEIN

TES à cavité double : Les raccordements clients, seront effectués au bornier d'a lim

entation sur le côté du LOG

EMEN

T boîtier (pas au bornier carte d'interconnexion) 11. Pour une IN

STALLATION

AU C

ANAD

A, suivre LE CO

DE C

ANAD

IEN D

E L'ÉLECTR

ICITÉ,

CSA N

o C22.1.

12. La TEMPÉR

ATUR

E AMBIAN

TE maxim

um autorisé pour le capteur LEVEL PLU

S version DIG

ITAL ou ANALO

GIQ

UE est de 71 C

°. Pour éviter les effets de la tem

pérature sur le processus des protections thermiques doivent être prises po ur assurer la tem

pérature ambiante environnante et ainsi qu'à l'intérieur

du boîtier du capteur la température ne doit pas dépasser 71 C

° 13. ATTEN

TION

: Le flexible du capteur a un rayon minim

um de courbure de 381 m

m (15 ")

14. Lorsqu'un EPL Ga est requis, les pièces de l'équipem

ent contenant des métaux légers (alum

inium ou titane) doivent être protégées contre les chocs afin

que les étincelles d 'impact ou de friction ne puissent pas se produire, en tenant com

pte des rares dysfonctionnements. Les m

esures pour éviter les étincelles d'im

pact ou de friction lors de l'utilisation de l'équipement contenant des m

étaux légers comprennent, m

ais sans s'y limiter:

- Montage vertical de la sonde

- Aucune agitation mécanique ne doit être utilisée

- Utilisation de puits d'im

mobilisation pour atténuer l'e ffet de l'agitation.

- Limitez le taux de changem

ent de niveau à des valeurs telles que les étincelles de friction ne peuvent pas se produire 15. ATTEN

TION

: La substitution de composants peut com

promettre la sécurité intrinsèque.

16.AVERTISSEM

ENT: L'ÉQ

UIPEM

ENT C

ON

TIENT D

ES PIÈCES D

E CO

FFRET N

ON

MÉTALLIQ

UES PO

UR

PRÉVEN

IR LES R

ISQU

ES D

'ÉTINC

ELLEMEN

T ÉLECTR

OSTATIQ

UE. LA SU

RFAC

E NO

N M

ÉTALLIQU

E NE D

OIT ÊTR

E NETTO

YÉE QU

E AVEC U

N C

HIFFO

N H

UM

IDE. La surface

peinte de l'équipement peut stocker une charge électrostatique et devenir une source d'inflam

mation dans les applications avec une hum

idité relative faible <~ 30%

d'humidité relative où la surface peinte est relativem

ent exempte de contam

ination de surface telle que la saleté, la poussière ou l'huile. Le nettoyagede la surface peinte ne doit être effectué qu'avec un chiffon hum

ide. 17. La C

lasse De Tem

pérature Applicable, La Plage De Tem

pératures De Procédé Et La Plage D

e Températures Am

biantes De L'Équipem

ent Sont Les Suivantes;T3 Avec Plage D

e Températures D

e Process De -40 ° C

À 150 ° CT4 Avec Plage D

e Températures D



e Températures D



e Températu res D


À 85 ° CPlage D

e Température Am

biante -40 ° C <Ta <71 ° C



LEVEL


I 36 I

Fig. 37: Intrinsically Safe FMC installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-2LEVEL

1 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**H


S 2/23/15D 8037 ADDED W




S 1/30/17G 8482 UPDATED BEND RADIUS TO 15" M

S 5/17/18H 8818 CHANGED NOTES 14, 16, 17 DR 12-10-19

NO

N H

AZARD

OU

S LOC

ATION

NO

N ZO

NE D

ANG

EREU

SEH

AZARD

OU

S LOC

ATION

ZON

E DAN

GER

EUSE

1. ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE M

TS LP SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

SEAL ALL CO

ND

UITS W

ITHIN

457 MM

(18"). 2. LO

OP C

ABLE MU

ST BE 24 AWG

TO 14 AW

G (.511M

M² to 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IELD. C

ABLE CAPAC

ITANC

E MU

ST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER m

). CABLE SH

IELD IS C

ON

NEC

TED TO

SYSTEM G

RO

UN

D IN

NO

N-H

AZARD

OU

S AREA. SEE IN

STALLATION

MAN

UAL FO

R

ADD

ITION

AL CABLE IN

FOR

MATIO

N.

3. THE R

ESISTANC

E BETWEEN

EARTH

GR

OU

ND

AND

THE IN

TRIN

SICALLY SAFE G

RO

UN

D M

UST BE LESS TH

AN 1 O

HM

. 4. TH

E TRAN

SDU

CER

FRAM

E SHALL BE G

RO

UN

DED

TO EAR

TH G

RO

UN

D D

IREC

TLY OR

THR

OU

GH

THE EQ

UIPM

ENT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQU

IPMEN

T CO

NN

ECTED

TO ASSO

CIATED

APPARATU

S MU

ST N

OT U

SE OR

GEN

ERATE M

OR

E THAN

250 VRM

S OR

VDC.

6. ASSOC

IATED APPAR

ATUS M

ANU

FACTU

RER

'S INSTALLATIO

N D

RAW

ING

MU

ST BE FO

LLOW

ED W

HEN

INSTALLIN

G TH

IS EQU

IPMEN

T 7. O

NLY U

SE CEC

APPRO

VED BAR

RIER

S. 8. APPR

OVED

LOO

P SEPARATIO

N M

ETHO

DS:

*RU

N LO

OPS IN

SEPARATE C

ABLES *R

UN

LOO

PS IN SEPAR

ATE GR

OU

ND

ED SH

IELDS

9. ENTITY PAR

AMETER

S EACH

LOO

P: U

i = 28 VDC

Ii = 120 mA

Ci = 0 µF

Li = 5 µH Pi = 840 m

W 10. D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D).

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(Canada). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

AGEN

CE D

ESSIN contrôlée ( C

ANAD

A ) . AUC

UN

CH

ANG

EMEN

T sans l'accord préalable AGEN

CE APPR

OBATIO

N

24 VDC

CO

NTR

OL

INPU

T 1

CO

NTR

OL

INPU

T 2

APPRO

VED SAFETY

BARR

IER sécurité approuvé BAR

RIÈR

ELO

OP VO

LTAGE

SHIELD

SHIELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

FM

APPROVED

US

C



SING

LE OR

DU

AL CAVITY

NEM

A HO

USIN

G

INTRINSICALLY SAFECL. I, DIV. 1, GR. ABCDCL.I Zone 0/1 Ex ia IIC T4Ta = -50 to 71°C ; IP65

APPRO

VED SAFETY

BARR

IER sécurité approuvé BAR

RIÈR

E



11 FOR

INSTALLATIO

N W

ITHIN

CAN

ADA, SEE C

ANAD

IAN ELEC

TRIC

AL CO

DE, C

SA No

C22.1.

12.THE M

AXIMU

M PER

MITTED

AMBIEN

T TEMPER

ATUR

E OF TH

E LEVEL PLUS

DIG

ITAL/ANALO

G LEVEL TR

ANSM

ITTER IS 71 °C

. TO AVO

ID TH

E EFFECTS O

F PRO

CESS

TEMPER

ATUR

E AND

OTH

ER TH

ERM

AL EFFECTS C

ARE SH

ALL BE TAKEN TO

ENSU

RE TH

ESU

RR

OU

ND

ING

AMBIEN

T AND

THE AM

BIENT IN

SIDE TH

E TRAN

SMITTER

HO

USIN

G D

OES

NO

T EXCEED

71°C 13.C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381MM

(15") 14 . W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT

METALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

TH

AT IMPAC

T OR

FRIC

TION

SPARKS C

ANN

OT O

CC

UR

, TAKING

INTO

ACC

OU

NT

RAR

E MALFU

NC

TION

. MEASU

RES TO

PREVEN

T IMPAC

T OR

FRIC

TION

SPARKS

WH

EN U

SING

THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS INC

LUD

E BUT AR

E N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KSC

ANN

OT O

CC

UR

15.WAR

NIN

G: SU

BSTITUTIO

N O

F CO

MPO

NEN

TS MAY IM

PAIR IN

TRIN

SIC SAFETY.

16.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E PARTS,

TO PR

EVENT TH

E RISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC

SUR

FACE SH

OU

LD O

NLY BE C

LEANED

WITH

A DAM

P CLO

TH. PAI N

TED SU

RFAC

E O

F THE EQ

UIPM

ENT M

AY STOR

E ELECTR

OSTATIC

CH

ARG

E AND

BECO

ME A

SOU

RC

E OF IG

NITIO

N IN

APPLICATIO

NS W

ITH A LO

W R

ELATIVE HU

MID

ITY <~30%R

ELATIVE HU

MID

ITY WH

ERE TH

E PAINTED

SUR

FACE IS R

ELATIVELY FREE O

F SU

RFAC

E CO

NTAM

INATIO

N SU

CH

AS DIR

T, DU

ST OR

OIL. C

LEANIN

G O

F THE

PAINTED

SUR

FACE SH

OU

LD O

NLY BE D

ON

E WITH

A DAM

P CLO

TH.

17.THE APPLIC

ABLE TEMPER

ATUR

E CLASS, PR

OC

ESS TEMPER

ATUR

E RAN

GE

AND

AMBIEN

T TEMPER

ATUR

E RAN

GE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°C < TA < 71°C

NOTES: (FO

R NOTES IN FRENCH SEE PAG

E 3, NOTES PO

UR VOIR EN FRANÇAIS PA

GE 3)


I 37 I


DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

DETAIL H

SCALE 1 : 1

D

E

F

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-2LEVEL

2 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**H


S 2/23/15D 8037 ADDED W






LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND


asse LUG


UR

ITÉ DE TER

RE

WAR

NIN

G:

CO

ND

UIT SEALS R

EQU

IRED

WITH

IN 457 m

m (18") O

F HO

USIN

G.

Étanchéité des conduits requis dans les 457 mm

(18") DU

LOG

EMEN

T.

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING




A GAUGE)

WIRING CHART(FOR NEM

A GAUGE)



WIRE COLOR

SIGNALRED

LOOP 1+BLACK

LOOP 1-BLUE

LOOP 2-W

HITELOOP 2+

GREENN/A

DRAIN WIRE

EARTH GROUND

PIN #SIGNAL

PIN 1LOOP 1-

PIN 2LOOP 1+

PIN 3LOOP 2-

PIN 4LOOP 2+

PIN 5N/A

PIN 6EARTH GROUND


I 38 I


11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-2LEVEL

3 3

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**H


S 2/23/15D 8037 ADDED W






NO

TES:1. La réglem


RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X.Sceller tous les conduits à m

oins de 457 mm

(18"). 2. Boucle de câble doit être de 24 AW

G à 14 AW

G (.511M

M2 à 1.6M

M2)

Paire Torsadée Blindée avec le bouclier. La capacité du câ ble devraÊtre inférieure à 30 pF PAR

PIED (98 pF PAR

M). Le blindage du câble est raccordé

À la terre EN ZO

NE N

ON

DAN

GER

EUSE. VO

IR m

anuel d'installationIN

FOR

MATIO

NS de câble supplém

entaire. 3. La résistance entre la TER

RE ET la zone IN

TRIN

SEQU

ED

oit être inférieure à 1 ohm.

4. Le boîtier du capteur doit être relié à la TERR

E directement ou par

L'équipement sur lequel il est m

onté. 5. Equipem

ent de co mm

ande relié à l'appareil associé ne doit pas utiliser ou générer plus de 250 VRM

S OU

VDC

6 Le plan d'installation associé du fabricant de l'appareil doit être suivi lors de l'installation de cet équipement

7. UTILISER

UN

IQU

EMEN

T DES BAR

RIER

ES APPRO

UVÉES C

EC 8. approuvent les m

éthodes de séparation Loop: * BO

UC

LES RU

N dans des câbles séparés

* BOU

CLES R

UN

Shields terre séparés 9. Param

ètres d'entité chaque boucle: U

i = 28 VDC

Ii = 120 mA

Ci = 0 µF

Li = 5 µH Pi = 840 m

W 10. EN

CEIN

TES à cavité double : Les raccordements clients, seront effectués au bornier d'alim

entation sur le côté du LOG

EMEN

T boîtier (pas au bornier carte d'interconnexion) 11. Pour une IN

STALLATION

AU C

ANAD

A, suivre LE CO

DE C

ANAD

IEN D

E L'ÉLEC TRIC

ITÉ,C

SA No C

22.1. 12. La TEM

PÉRATU

RE AM

BIANTE m

aximum

autorisé pour le capteur LEVEL PLUS version D

IGITAL ou AN

ALOG

IQU

E est de 71 C°. Pour éviter les effets de la tem

pérature sur le processus des protections therm

iques doivent être prises pour assurer la température am

biante environnante et ainsi qu'à l'intérieur du boîtier du capteur la température ne doit pas

dépasser 71 C°

13. ATTENTIO

N : Le flexible du capteur a un rayon m

inimum

de courbure de 381mm

(15 ") 14. Lorsqu'un EPL G

a est requis, les pièces de l'équipement contenant des m

étaux légers (aluminium

ou titane) doivent être protégées contre les chocs afin que les étincelles d'im

pact ou de friction ne puissent pas se produire, en tenant compte des rares dysfonctionnem

ents. Les mesures pour éviter les étincelles d'im

pact ou de fr iction lors de l'utilisation de l'équipem

ent contenant des métaux légers com

prennent, mais sans s'y lim

iter:- M

ontage vertical de la sonde- Aucune agitation m

écanique ne doit être utilisée- U

tilisation de puits d'imm

obilisation pour atténuer l'effet de l'agitation.- Lim

itez le taux de changement de niveau à des valeurs telles que les étincelles de friction ne peuvent pas se produire

15. ATTENTIO

N : La substitution de composants peut com

promettre la sécurité intrinsèque.

16.AVERTISSEM

ENT: L'ÉQ

UIPEM

ENT C

ON

TIENT D

ES PIÈCES D

E CO

FFRET N

ON

MÉTALLIQ

UES PO

UR

PRÉVEN

IR LES R

ISQU

ES D'ÉTIN

CELLEM

ENT

ÉLECTR

OSTATIQ

UE. LA SU

RFAC

E NO

N M

ÉTALLIQU

E NE D

OIT ÊTR

E NETTO

YÉE QU

E AVEC U

N C

HIFFO

N H

UM

IDE. La surface peinte de l'équipem

ent peut stocker une charge électrostatique et devenir une source d'inflam

mation dans les applications avec une hum

idité relative faible <~ 30% d'hum

idité relative où la surface peinte est relativement

exempte de contam

ination de surface telle que la saleté, la poussière ou l'huile. Le nettoyage de la surface peinte ne doit être effectué qu'avec un chiffon humide.

17. La classe de température applicable, la plage de tem

pératures de procédé et la plage de températures am

biantes de l'équipement sont les suivantes;

T3 avec plage de températures de process de -40 ° C

à 150 ° CT4 avec plage de tem

pératures de process de -40 ° C à 135 ° C

T5 avec plage de températures de process de -40 ° C

à 100 ° CT6 avec plage de tem

pératures de process de -40 ° C à 85 ° C

Plage de température am

biante -40 ° C <Ta <71 ° C




I 39 I

13.4.2 FMC XP



2. Cables shall be rated > 5°C above maximum ambient temperature.


4. The equipment can be installed in the boundary wall between an EPL Ga area and the less hazardous area, EPL Gb. In this configuration, the process connection is installed in EPL Ga, while the transmitter housing is installed in EPL Gb. Refer to installation instructions.



ambient temperature range of the equipment is as follows;• T3 with Process Temperature Range of -40°C to 150°C• T4 with Process Temperature Range of -40°C to 135°C• T5 with Process Temperature Range of -40°C to 100°C• T6 with Process Temperature Range of -40°C to 85°C• Ambient Temperature Range -40°C < Ta < 71°C



cannot occur

Fig. 40: Explosion proof, FMC label, Modbus or DDA Housing Option G, H, or L

Fig. 41: Explosion proof, FMC label, Modbus or DDA, Housing Option D, E

Fig. 42: Explosion proof, FMC label, HART®, Housing Option G, H, or L

Fig. 43: Explosion proof, FMC label, HART®, Housing Option D, E

1

1

2

2

A A

B B

REV ECO # DESCRIPTIONTITLE

SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METR IC

FIRST ANGLE A 551706-x A

1 1 DRAWN BY: MS

***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION TO APPROVAL AGENCY(S).***A MS 7/28/16



FM16CA0130X

INSTALL PER # # 651552-2/651595-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: RS485

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF

THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT.POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR BCD T6...T3. Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

7957 RELEASE FOR PRODUCTION

(ACP) LABEL, LP, XP CANADA - DIGITAL

R FM APPROVED

P/N 551706-1 REV B

LEVEL

1:1

!

C 1

1

2

2

A A

B B


SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES 0.5 0.1




METR IC

FIRST ANGLE A 551706-x A

1 1 DRAWN BY: MS

***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION TO APPROVAL AGENCY(S).***A MS 7/28/16



FM16CA0130X

INSTALL PER # # 651552-2/651595-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: RS485

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF

THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT.POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR. BCD T6...T3 Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

7957 RELEASE FOR PRODUCTION

(ACP) LABEL, LP, XP CANADA - DIGITAL

R FM APPROVED

P/N 551706-2 REV B

LEVEL

1:1

!

C

Level Plus TransmitterFM16CA0130X


WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE PRESENT FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF

THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR. BCD T6...T3Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

INSTALL PER # 651553-2/651597-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: 4-20mA

FM CAPPROVED

P/N 551708-x RevB

R

!

Level Plus TransmitterFM16CA0130X


WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE PRESENT FOR ZONE INSTALLATIONS, A SEAL SHALL BE INSTALLED WITHIN 50mm OF

THE ENCLOSURE. FOR DIVISION INSTALLATIONS A SEAL SHALL BE INSTALLED WITHIN 18 INCHESOF THE ENCLOSURE ATTENTION : NE PAS OUVRIR UNE ATMOSPHÈRE EXPLOSIVE PRESENT POUR INSTALLATIONS DE ZONE, UN SORTIE EST INSTALLÉ DANS LES 50 mm DE L'ENCEINTE. POUR INSTALLATIONS DE DIVISION ALE SORTIE EST INSTALLÉ DANS LES 18 POUCES DE L'ENCEINTE

EXPLOSIONPROOF CL. I, DIV. 1, GR. BCD T6...T3Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP 65

INSTALL PER # 651553-2/651597-2MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)INPUT: 28V (120mA)max OUTPUT: 4-20mA

FM CAPPROVED

P/N 551708-x RevB

R

!

13.4.2.2 Labels


I 40 I


Fig. 44: Explosion proof, FMC Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-2C

LEVEL1

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***

A 7957 RELEASED TO PRODUCTION MS 10/22/15

B 8482 UPDATED WIRING DW

G TO ANALOG MS 5/17/18

C 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19

LOOP 2+

LOOP 2-

EARTH GROUND

LOOP 1+

LOOP 1-

EARTH GROUND

SEE NOTE 8EPL Ga

EPL Gb

NO

N H

AZARD

OU

S LOC

ATION

HAZAR

DO

US LO

CATIO

N

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(Canada). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

FM

APPROVED US

C

(ACP) INSTALLATION DWG LP ANALOG

EXPLOSION PROOF CANADA

SING

LE OR

DU

AL CAVITY

FM Canada - FM

16CA0130X

EXPLOSION PROOFCL. I, DIV. 1, GR. BCD T6...T3Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C ; IP65

CO

ND

UIT SEAL

CO

ND

UIT

CO

ND

UIT SEAL

SEE NO

TE 1

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m (2") O

F THE

ENC

LOSU

RE. FO

R D

IVISION

INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 457m

m (18") O

F THE EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PREVEN

T IGN

ITION

OF FLAM

MABLE O

R C

OM

BUSTIBLE ATM

OSPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A D

AMP C

LOTH





RELATIVE HUM


INATION SUCH AS DIRT, DUST OR OIL. CLEANING OF THE PAINTED SU RFACE SHOULD ONLY BE DONE W

ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE INSTALLED

IN TH

E BOU

ND

ARY W

ALL BETWEEN

A ZON

E 0 AREA AN

D TH

E LESS H

AZARD

OU

S AREA, ZO

NE 1. IN

THIS C

ON

FIGU

RATIO

N, TH

E PRO

CESS C

ON

NEC

TION

IS INSTALLED

IN

A ZON

E 0 AREA, W

HILE TH

E TRAN

SMITTER

HO

USIN

G IS IN

STALLED IN

A ZON

E 1 AREA.

9. THE APPLIC

ABLE TEMPER

ATUR

E CLASS O

F THE EQ

UIPM

ENT, AM

BIENT TEM

PERATU

RE R

ANG

E, AN

D M

AXIMU

M PR

OC

ESS TEMPER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AGN

ETIC LEVEL G

AUG

E MAKE SU

RE TH

E ELECTR

ON

IC H

EAD AN

D PR

ESSUR

E BAR

RIER

HAVE A M

INIM

UM

SPACIN

G O

F 5 INC

HES. SEE IN

STALLATION

MAN

UAL FO

R D

ETAIL11. FLAM

EPATHS AR

E NO

T FOR

REPAIR

12. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS (ALUM

INU

M O

R TITAN

IUM

) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO

ACC

OU

NT R

ARE M

ALFUN

CTIO

N M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS WH

EN U

SING

THE

EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R

5"[127mm

] Minim

um


I 41 I


DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-2C

LEVEL2

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***





LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND


asse LUG


UR

ITÉ DE TER

RE

WAR

NIN

G:

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

MEN

TS. FO

R ZO

NE IN

STALLATION


STALLED W

ITHIN

50mm

OF TH

E EN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


S TALLED W

ITHIN

457mm

(18") OF TH

E ENC

LOSU

RE.

AVERTISSEM

ENT:

POU

R IN

STALLATION

S DE ZO

NE, U

N SO

RTIE EST IN

STALLÉ DAN

S LES 50mm

(2") DE L'EN

CEIN

TE. PO

UR

INSTALLATIO

NS D

E DIVISIO

N ALE SO

RTIE EST IN

STALLÉ DAN

S LES 457mm

(18") DE L'EN

CEIN

TE

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY H

OU

SING





I 42 I


11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-2C

LEVEL3

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***





NO

TES:1. La réglem


RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X. PO

UR

INSTALLATIO

NS D

E ZON

E, UN

SOR

TIE EST INSTALLÉ D

ANS LES 50m

m (2") D

E L'ENC

EINTE.

POU

R IN

STALLATION

S DE D

IVISION

ALE SOR

TIE EST INSTALLÉ D

ANS LES 457m

m (18") D

E L'ENC

EINT E

2. ENC

EINTES à cavité double : Les raccordem

ents clients, seront effectués au bornier d'alimentation sur le côté du LO

GEM

ENT boîtier (pas au bornier carte d'interconnexion)

3. ATTENTIO

N: LES IN

STRU

MEN

TS FLEXIBLES AVEC U

N R

ADIO

DE M

INIM

UM

DE 381m

m (15 ")

4. ATTENTIO

N: Pour éviter l'inflam

mation d'atm

osphères inflamm

ables ou combustibles,

DÉBR

ANC

HEZ L'ALIM

ENTATIO

N AVAN

T D'IN

TERVEN

IR5. AVER

TISSE MEN

T: L'ÉQU

IPEMEN

T CO

NTEN

UE D

ES PIÈCES ET PR

OC

ÉDÉS N

ON

-METALLIQ

UES PO

UR

PRÉVEN

IR LE R

ISQU

E D'ÉC

LAIRAG

E ÉLECTR

OSTATIQ

UE. LA SU

RFAC

E ET LES PIÈCES D

E PRO

CÉD

UR

E NO

N M

ÉTALLIQU

ES DO

IVENT SEU

LEMEN

T EFFEC

TEZ UN

PANN

EAU D

E PLAISIR. LA SU

RFAC

E PEINTÉE D

E L'ÉQU

IPEMEN

T PEUT C

ON

SERVER

LE CH

ARG

E ÉLECTR

OSTATIQ

UE

ET DEVEN

IR U

NE SO

UR

CE D

'ALLUM

AGE D

ANS D

ES APPLICATIO

NS AVEC

UN

E HU

MID

ITÉ BASSE RELATIVE < ~ 30%

RELATIVE

HU

MID

ITE OÙ

LA SUR

FACE PEIN

TUR

E EST RELATIVEM

ENT LIBR

E DE C

ON

TAMIN

ATION

DE SU

RFAC

E TELS Q

UE LA VIAN

DE, LA PO

USSIÈR

E OU

L'HU

ILE. LE NETTO

YAGE D

E LA SUR

FACE PEIN

TUR

E DO

IT ÊTRE FAIT

AVEC U

N PAN

NEAU

DE PLAISIR

. 6. C

ABLES doit être évalué> 5C D

ESSUS M

AXIMU

M TEM

PERATU

RE AM

BIANTE.

7. POU

R M

AINTEN

IR LA N

OTATIO

N D

E PRO

TECTIO

N D

E ING

RESS IP65, du ruban téflon (3 BAN

DES) ou PIPE D

OPE D

EVRA ÊTR

E UTILISÉ. C

ON

SULTER

LES INSTR

UC

TION

S D'IN

STALLATION

. 8. L'ÉQ

UIPEM

ENT PEU

T ÊTRE IN

STALLÉ DAN

S LE MU

R D

E LIMITE EN

TRE U

NE ZO

NE 0 ET LA

ZON

E MO

INS D

ANG

EREU

SE, ZON

E 1. DAN

S CETTE C

ON

FIGU

RATIO

N, LA C

ON

NEXIO

N D

U PR

OC

ESSUS EST IN

STALLEE D

ANS U

NE ZO

NE 0, LO

RSQ

UE LE BO

ITIER D

E L'EMETTEU

R EST IN

STALLE DAN

S UN

E ZON

E DE LA ZO

NE 1.

9. LA TEMPER

ATUR

E CLASSE APPLIC

ABLE DE L'ÉQ

UIPEM

ENT , TEM

P ERATU

RE AM

BIANTE R

ANG

E, ET M

AXIMU

M PR

OC

ESSUS TEM

PERATU

RE D

E L'APPAREIL EST C

E QU

I SUIT ;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C Ta+71°C

10.LOR

S DU

MO

NTAG

E SUR

UN

E J AUG

E DE N

IVEAU M

AGN

ÉTIQU

E, ASSUR

EZ-VOU

S QU

E LA TÊTE ÉLECTR

ON

IQU

E ET LA PRESSIO

N BAR

RIÈR

E A UN

ESPACEM

ENT M

INIM

UM

DE 5 PO

UC

ES. VOIR

LE MAN

UEL D

'INSTALLATIO

N PO

UR

DETAIL

11.CH

EMIN

DE FLAM

ME N

E SON

T PAS À RÉPAR

ER12. Lorsqu'un EPL G





ents. Les mesures pour éviter les

étincelles d'impact ou de friction lors de l'utilisation de l'équipem



iter:- M




obilisation pour atténuer l'ef fet de l'agitation.- Lim





I 43 I

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-2C

1

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***C 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19


B 8482 UPDATED BEND RADIUS TO 15" MS 5/17/18

EARTH GROUND

Rx /Tx-

Rx /Tx+

EARTH GROUND

COMM

ON-

24 VDC

EPL Ga

EPL GbSEE NOTE 8


AGEN

CY C

ON

TRO

LLED D

RAW

ING

(CAN

ADA). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERMINAL



LEVEL

FM

APPROVED

C

N/A

EXPLOSION PROOFCL. I, DIV. 1, GR. BCD T6...T3Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C ; IP65

FM CANADA- FM

16CA0130X

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

FOR

ZON

E INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 50m

m O

F THE

ENC

LOSU

RE. FO

R D

IVISION

INSTALLATIO

NS, A SEAL SH

ALL BE INSTALLED

WITH

IN 457 (18") O

F THE EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PREVEN

T IGN

ITION

OF FLAM

MABLE O

R C

OM

BUSTIBLE ATM

OSPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A D

AMP C

LOTH





RELATIVE HUM



ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE IN

STALLED IN

THE BO

UN

DAR

Y WALL BETW

EEN A ZO

NE 0 AR

EA AND

THE

LESS HAZAR

DO

US AR

EA, ZON

E 1. IN TH

IS CO

NFIG

UR

ATION

, THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED

IN A ZO

NE 0 AR

EA, WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

IN A ZO

NE 1 AR

EA. 9. TH

E APPLICABLE TEM

PERATU

RE C

LASS OF TH

E EQU

IPMEN

T, AMBIEN

T TEMPER

ATUR

E RAN

GE,

AND

MAXIM

UM

PRO

CESS TEM

PERATU

RE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°CTa+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AGN

ETIC LEVEL G

AUG

E MAKE SU

RE TH

E ELECTR

ON

IC H

EAD AN

D PR

ESSUR

E BAR

RIER

HAVE A M

INIM

UM

SPACIN

G O

F 5 INC

HES. SEE IN

STALLATION

MAN

UAL FO

R D

ETAIL11. FLAM

EPATHS AR

E NO

T FOR

REPAIR

12. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS (ALUM

INU

M O

R TITAN

IUM

) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO

ACC

OU

NT R

ARE M

ALFUN

CTIO

N M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS WH

EN U

SING

THE

EQU

IPMEN

T CO

NTAIN

ING

LIGH

T ME

TALS INC

LUD

E BUT AR

E NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R

CONDUIT

CONDUIT SEAL

SEE NOTE 1

CONDUIT SEAL

5" [127mm

] Minim

um

Fig. 47: Explosion proof, FMC Installation Drawing, HART®, Page 1


I 44 I

DETAIL FSCALE 1.60 : 1

DETAIL GSCALE 3 : 1

DETAIL HSCALE 1.2

F

G

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-2C

2

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC





GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EAR

THIN

G G

RO

UN

D SYSTEM

Le client doit relier la masse LU

G à l'extérieur pour le systèm

e au sol SÉCU

RITÉ D

E TERR

E W

ARN

ING

: FO

R ZO

NE IN

STALLATION


STALLED W

ITHIN

50mm

(2") OF TH

E EN

CLO

SUR

E. FOR

DIVISIO

N IN

STALLATION


STALLED W

ITHIN

457mm

(18") OF TH

E ENC

LOSU

RE.

AVERTISSEM

ENT:

POU

R IN

STALLATION

S DE ZO

NE, U

N SO

RTIE EST IN

STALLÉ DAN

S LES 50 mm

DE L'EN

CEIN

TE. PO

UR

INSTALLATIO

NS D

E DIVISIO

N ALE SO

RTIE EST IN

STALLÉ DAN

S LES 18 POU

CES D

E L'ENC

EINTE






I 45 I

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-2C

3

3 D

RAW

N BY:

MS

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC




NO

TES:1. La réglem


RS D

'INSTALLATIO

N D

U C

APTEUR

DE N

IVEAU D

ANS D

ES ENVIR

ON

NEM

ENTS D

ANG

EREU

X. PO

UR

INSTALLATIO

NS D

E ZON

E, UN

SOR

TIE EST INSTALLÉ D

ANS LES 50 m

m D

E L'ENC

EINTE.

POU

R IN

STALLATION

S DE D

IVISION

ALE SOR

TIE EST INSTALLÉ D

ANS LES 457m

m (18") D

E L'ENC

EINTE

2. ENC

EINTES à cavité double : Les raccordem

ents clients, seront effectués au bornier d'alimentation sur le côté du LO

GEM

ENT boîtier (pas au bornier carte d'interconnexion)

3. ATTENTIO

N: LES IN

STRU

MEN

TS FLEXIBLES AVEC U

N R

ADIO

DE M

INIM

UM

DE 381m

m (15 ")

4. ATTENTIO

N: Pour éviter l'inflam

mation d'atm

osphères inflamm

ables ou combustibles,

DÉBR

ANC

HEZ L'ALIM

ENTATIO

N AVAN

T D'IN

TERVEN

IR5. AVER

TISSEMEN

T: L'ÉQU

IPEMEN

T CO

NTEN

UE D

ES PIÈCES ET PR

OC

ÉDÉS N

ON

-METALLIQ

UES PO

UR

PRÉVEN

IR LE R

ISQU

E D'ÉC

LAIRAG

E ÉLECTR

OSTATIQ

UE. LA SU

RFAC

E ET LES PIÈCES D

E PRO

CÉD

UR

E NO

N M

ÉTALLIQU

ES DO

IVENT SEU

LEMEN

T EFFEC

TEZ UN

PANN

EAU D

E PLAISIR. LA SU

RFAC

E PEINTÉE D

E L'ÉQU

IPEMEN

T PEUT C

ON

SERVER

LE CH

ARG

E ÉLECTR

OSTATIQ

UE

ET DEVEN

IR U

NE SO

UR

CE D

'ALLUM

AGE D

ANS D

ES APPLICATIO

NS AVEC

UN

E HU

MID

ITÉ BASSE RELATIVE <~ 30%

RELATIVE

HU

MID

ITE OÙ

LA SUR

FACE PEIN

TUR

E EST RELATIVEM

ENT LIBR

E DE C

ON

TAMIN

ATION

DE SU

RFAC

E TELS Q

UE LA VIAN

DE, LA PO

USSIÈR

E OU

L'HU

ILE. LE NETTO

YAGE D

E LA SUR

FACE PEIN

TUR

E DO

IT ÊTRE FAIT

AVEC U

N PAN

NEAU

DE PLAISIR

. 6. C

ABLES doit être évalué> 5C D

ESSUS M

AXIMU

M TEM

PERATU

RE AM

BIANTE.

7. POU

R M

AINTEN

IR LA N

OTATIO

N D

E PRO

TECTIO

N D

E ING

RESS IP65, du ruban téflon (3 BAN

DES) ou PIPE D

OPE D

EVR

A ÊTRE U

TILISÉ. CO

NSU

LTER LES IN

STRU

CTIO

NS D

'INSTALLATIO

N.

8. L'ÉQU

IPEMEN

T PEUT ÊTR

E INSTALLÉ D

ANS LE M

UR

DE LIM

ITE ENTR

E UN

E ZON

E 0 ET LA ZO

NE M

OIN

S DAN

GER

EUSE, ZO

NE 1. D

ANS C

ETTE CO

NFIG

UR

ATION

, LA CO

NN

EXION

DU

PRO

CESSU

S EST INSTALLEE

DAN

S UN

E ZON

E 0, LOR

SQU

E LE BOITIER

DE L'EM

ETTEUR

EST INSTALLE D

ANS U

NE ZO

NE D

E LA ZON

E 1 9. LA TEM

PERATU

RE C

LASSE APPLICABLE D

E L'ÉQU

IPEMEN

T , TEMPER

ATUR

E AMBIAN

TE RAN

GE,

ET MAXIM

UM

PRO

CESSU

S TEMPER

ATUR

E DE L'APPAR

EIL EST CE Q

UI SU

IT ; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°CTa+71°C

10.LOR

S DU

MO

NTAG

E SUR

UN

E JAUG

E DE N

IVEAU M

AGN

ÉTIQU

E, ASSUR

EZ-VOU

S QU

E LA TÊTE ÉLECTR

ON

IQU

E ET LA PRESSIO

N BAR

RIÈR

E A UN

ESPACEM

ENT M

INIM

UM

DE 5 PO

UC

ES. VOIR

LE MAN

UEL D

'INSTALLATIO

N PO

UR

DETAIL

11.CH

EMIN

DE FLAM

ME N

E SON

T PAS À RÉPAR

ER12. Lorsqu'un EPL G





ents. Les mesures pour éviter les

étincelles d'impact ou de friction lors de l'utilisation de l'équipem



iter:- M




obilisation pour atténuer l'effet de l'agitation.- Lim






I 46 I

13.5 ATEX/IECEx

13.5.1 ATEX/IECEx IS

13.5.1.1 Specific conditions of safe use


cannot occur

2. The maximum permitted ambient temperature of the Level Plus Digital/Analog Level Transmitter is 71 °C. To avoid the effects of process temperature and other thermal effects care shall be taken to ensure the surrounding ambient and the ambient inside the transmitter housing does not exceed 71°C



1

12

A A

B B


SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES0.5 0.1




METRIC

FIRST ANGLE 551629-3 C

1 1

DRAWN BY: NJ

A NJ



FM14ATEX0068XIECEx FMG 14.0032X

II 1/2 G Ex ia IIC T4 Ga/Gb Ta = -50°C to +71°C ; IP65

when connected in accordancewith FM approved installation drawing # 651543-3


Model No:

Serial No:

Date :

R


LEVEL1:1


(ACP) LABEL, LP, IS ATEX/IECEx - DIGITAL

10/24/14

2809


P/N 551629-3 Rev C

NOTES:STANDARD LETTERING UNIVERS 55OR ITC GARAMOND BOOK.DIMENSIONS IN BRACKETS [ ] AREIN INCHES.

3. MATERIAL: 3M 7883 METALLIZEDPOLYESTER FOIL W/GAS RESISTANTINK.

IP RATING WAS 66 1/19/15NJ7847BC 8176 CHANGED CE TO 2809 MS 5-21-19

Fig. 50: Intrinsically Safe FMC label, Modbus and DDA, NEMA Housing

Fig. 51: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, NEMA Housing

1

12

A A

B B


SIZE DWG NO. REV

PRODUCT LINESCALE:

BY DATE

SHEET OF


0 PLACESMM

1 PLACEMM

ANGLES0.5 0.1




METRIC

FIRST ANGLE 551641-3 C

1 1

DRAWN BY: MS




II 1/2 G Ex ia IIC T4 Ga/Gb Ta = -50°C to +71°C ; IP65when connected in accordance with FM approved installation drawing # 651544-3

Model No:

Serial No:

Date:


LEVEL1:1

(ACP) LABEL, LP, IS ATEX/IECEx - ANALOG


2809

P/N 551641-3 Rev C

NOTES:1. STANDARD LETTERING UNIVERS 55

OR ITC GARAMOND BOOK.2. DIMENSIONS IN BRACKETS [ ] ARE

IN INCHES.3. MATERIAL: 3M 7883 METALLIZED

POLYESTER FOIL W/GAS RESISTANTINK.

C 8176 CHANGED CE TO 2809 MS 5-21-19

R

B 7847 IP RATING WAS 66 NJ 1-19-15

13.5.1.2 Labels


I 47 I


II 1/2 G Ex ia IIC T4 Ga/GbTa = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNING.



R

2809


P/N 551705-X Rev E


II 1/2 G Ex ia IIC T4 Ga/GbTa = -50°C TO +71°C ; IP65WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETYREFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS



R 2809


P/N 551703-X Rev E

Fig. 52: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, Single and Dual Cavity Housing

Fig. 53: Intrinsically Safe ATEX/IECEx label, Modbus and DDA, Single and Dual Cavity Housing


I 48 I


Fig. 54: Intrinsically Safe ATEX / IECEx installation drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-3LEVEL

1 2

(ACP) IN

STALLATIN D

WG

LP DIG

ITAL INTR

INSIC

ALLY SAFE FOR

ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

I


S 2/23/15D 8037 ADDED W


F 8183 REV WITHOUT ANY CHANGE M

S 8/18/17E 8256 UPDATED W

IRING CHART ON SHEET 2 MS 1-30-17

G 8482 UPDATED BEND RADIUS TO 15" MS 5-17-18

H 8716 UPDATED CE MARK TO 2809 M

S 6-12-19 I 8818 CHANGED NOTES 1, 14, 16, 17 DR 12-10-19

24 VDC

COMM

ON- >

Rx/Tx+

Rx/Tx -

GROUND



Rx/Tx-

Rx/Tx+

GND

+24V

SAFETY BARRIER SAFETY BARRIER

SAFETY BARRIER


INTR

INSIC

ALLY SAFEFM

14ATEX0068XIEC

Ex FMG

14.0032X

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERMINAL

2809

II 1/2 G Ex ia T4 Ga/GbTa = -50 TO 71°C; IP65

1.ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE LEVEL SEN

SOR

IN H

AZARD

OU

S ENVIR

ON

MEN

TS. SEAL ALL C

ON

DU

ITS WITH

IN 50m

m (2") O

F ENC

LOSU

RE.

2.LOO

P CABLE M

UST BE 24 AW

G TO

14 AWG

(.511MM

² TO 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IELD. C

ABLE CAPAC

ITANC

E M

UST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER M

). CABLE SH

IELD

IS CO

NN

ECTED

TO SYSTEM

GR

OU

ND

IN N

ON

-HAZAR

DO

US AR

EA. SEE IN

STALLATION

MAN

UAL FO

R AD

DITIO

NAL C

ABLE INFO

RM

ATION

. 3.TH

E RESISTAN

CE BETW

EEN EAR

TH G

RO

UN

D AN

D TH

E INTR

INSIC

ALLY SAFE G

RO

UN

D M

UST BE LESS TH

AN 1 O

HM

. 4.TH

E TRAN

SDU

CER

FRAM

E SHALL BE G

RO

UN

DED

TO EAR

TH G

RO

UN

D D

IREC

TLY OR

THR

OU

GH

THE EQ

UIPM

ENT O

N W

HIC

H IT IS M

OU

NTED

. 5. C

ON

TRO

L EQU

IPMEN

T CO

NN

ECTED

TO ASSO

CIATED

APPARATU S M

UST

NO

T USE O

R G

ENER

ATE MO

RE TH

AN 250 VR

MS O

R VD

C 6.ASSO

CIATED

APPARATU

S MAN

UFAC

TUR

ER'S IN

STALLATION

DR

AWIN

G M

UST BE FO

LLOW

ED W

HEN

INSTALLIN

G TH

IS EQU

IPMEN

T. 7.O

NLY U

SE ATEX/IEC APPR

OVED

BARR

IERS.

8.ENTITY PAR

AMETER

S: SU

PPLY: RX/TX-: R

X/TX+: U

i = 28VDC

Ui= 8.6V U

i= 8.6V Ii = 100M

A Ii = 10MA Ii = 10M

A C

i = 0 µF Ci = 0 µF C

i = 0 µF Li = 0 µH


Pi = 0.7 W Pi= 0.0215 W

Pi= 0.0215 W 9.TH

E ENTITY C

ON

CEPT ALLO

WS IN

TERC

ON

NEC

TION

OF IN

TRIN

SICALLY SAFE

APPARATU

S WITH

ASSOC

IATED APPAR

ATUS W

HEN

THE FO

LLOW

ING

IS TRU

E: Vm

ax OR

Ui ≥ Voc, VT O

R U

o; Im

ax OR

Ii ≥ Isc, It OR

Io; Pm

ax OR

Pi ≥ Po; C

a ≥ Ci + C


UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E OF H

OU

SING

(NO

T TO TER

MIN

AL BLOC

K ON

INTER

CO

NN

ECT BO

ARD

).

11. FOR INSTALLATION WITHIN THE EUROPEAN UNION, SEE EN 60079-14.

12.THE M

AXIMU

M PER

MITTED

AMBIEN

T TEMPER

ATUR

E OF TH

E LEVEL PLUS

DIG

ITAL/ANALO

G LEVEL TR

ANSM

ITTER IS 71 °C

. TO AVO

ID TH

E EFFECTS

OF PR

OC

ESS TEMPER

ATUR

E AND

OTH

ER TH

ERM

AL EFFECTS C

ARE SH

ALL BE TAKEN

TO EN

SUR

E THE SU

RR

OU

ND

ING

AMBIEN

T AND

THE AM

BIENT

INSID

E THE TR

ANSM

ITTER H

OU

SING

DO

ES NO

T EXCEED

71°C 13.C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381MM

(15") 14. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT

METALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO AC

CO

UN

T R

ARE M

ALFUN

CTIO

N. M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS W

HEN

USIN

G TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE

NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS C

ANN

OT O

CC

UR

15.WAR

NIN

G: SU

BSTITUTIO

N O

F CO

MPO

NEN

TS MAY IM

PAIR IN

TRIN

SIC SAFETY.

16.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E PARTS,

TO PR

EVENT TH

E RISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC SU

RFAC

E SHO

ULD

ON

LY BE CLEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED

SU

RFAC

E OF TH

E EQU

IPMEN

T MAY STO

RE ELEC

TRO

STATIC C

HAR

GE AN

D

BECO

ME A SO

UR

CE O

F IGN

ITION

IN APPLIC

ATION

S WITH

A LOW

RELATIVE

HU

MID

ITY <~30% R

ELATIVE HU

MID

ITY WH

ERE TH

E PAINTED

SUR

FAC E IS R

ELATIVELY FREE O

F SUR

FACE C

ON

TAMIN

ATION

SUC

H AS D

IRT, D

UST O

R

OIL. C

LEANIN

G O

F THE PAIN

TED SU

RFAC

E SHO

ULD

ON

LY BE DO

NE W

ITH A

DAM

P CLO

TH.

17.THE APPLIC

ABLE TEMPER

ATUR

E CLASS, PR

OC

ESS TEMPER

ATUR

E RAN

GE

AND

AMBIEN

T TEMPER

ATUR

E RAN

GE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C TO

85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°C < TA < 71°C

NOTES


I 49 I

Fig. 55: Intrinsically Safe ATEX / IECEx installation drawing, Modbus and DDA, Page 2


DETAIL CSCALE 3 : 1

DETAIL DSCALE 1.2

DETAIL ESCALE 1 : 1

A

C

D

E

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651543-3LEVEL

2 2

(ACP) IN

STALLATIN D

WG

LP DIG

ITAL INTR

INSIC

ALLY SAFE FOR

ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

I


S 2/23/15D 8037 ADDED W







S 6-12-19 I 8818 CHANGED NOTES 1, 14, 16, 17 DR 12-10-19


GND+24V

TX/RX-TX/RX+EARTH

GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

(2") OF H

OU

SING

.



A GAUGE)


A GAUGE)

WIRE COLOR

SIGNALRED

24 V PWR

BLACK 0 V PW

RBLUE

N/AW

HITERX TX +

GREENRX TX -

DRAIN WIRE

EARTH GROUND

PIN #SIGNAL

PIN 124 V PW

RPIN 2

0 V PWR

PIN 3N/A

PIN 4RX TX+

PIN 5RX TX-

PIN 6EARTH GROUND


I 50 I

Fig. 56: Intrinsically Safe ATEX / IECEx installation drawing, HART®, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-3LEVEL

1 2

(ACP) IN

STALLATIN D

WG

LP ANALO

G IN

TRIN

SICALLY SAFE FO

R ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

I


S 2/23/15D 8037 ADDED W







S 6-12-19I 8818 CHANGED NOTES 1, 14, 16, 17 DR 12-10-19

NO

N H

AZARD

OU

S LOC

ATION

HAZAR

DO

US LO

CATIO

N

1. ALL NATIO

NAL AN

D LO

CAL C

OD

ES AND

REG

ULATIO

NS M

UST BE AD

HER

ED TO

WH

EN IN

STALLING

THE M

TS LP SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

SEAL ALL CO

ND

UITS W

ITHIN

50mm

(2"). 2. LO

OP C

ABLE MU

ST BE 24 AWG

TO 14 AW

G (.511M

M² to 1.6M

M²)

SHIELD

ED TW

ISTED PAIR

CABLE W

ITH SH

IELD. C

ABLE CAPAC

ITANC

E MU

ST BE LESS TH

AN 30 pF PER

FOO

T (98 pF PER m

). CABLE SH

IELD IS CO

NN

ECTED

TO SYSTEM

GR

OU

ND

IN N

ON

-HAZAR

DO

US AR

EA. SEE INSTALLATIO

N M

ANU

AL FO

R AD

DITIO

NAL C

ABLE INFO

RM

ATION

. 3. TH

E RESISTAN

CE BETW

EEN EAR

TH G

RO

UN

D AN

D TH

E INTR

INSIC

ALLY SAFE GR

OU

ND

MU

ST BE LESS THAN

1 OH

M.

4. THE TR

ANSD

UC

ER FR

AME SH

ALL BE GR

OU

ND

ED TO

EARTH

GR

OU

ND

DIR

ECTLY O

R TH

RO

UG

H TH

E EQU

IPMEN

T ON

WH

ICH

IT IS MO

UN

TED.

5. CO

NTR

OL EQ

UIPM

ENT C

ON

NEC

TED TO

ASSOC

IATED APPAR

ATUS M

UST

NO

T USE O

R G

ENER

ATE MO

RE TH

AN 250 VR

MS O

R VD

C. 6. ASSO

CIATED

APPARATU

S MAN

UFAC

TUR

ER'S IN

STALLATION

DR

AWIN

G M

UST

BE FOLLO

WED

WH

EN IN

STALLING

THIS EQ

UIPM

ENT

7. ON

LY USE ATEX/IEC

APPRO

VED BAR

RIER

S. 8. APPR

OVED

LOO

P SEPARATIO

N M

ETHO

DS:

*RU

N LO

OPS IN

SEPARATE C

ABLES *R

UN

LOO

PS IN SEPAR

ATE GR

OU

ND

ED SH

IELDS

9. ENTITY PAR

AMETER

S EACH

LOO

P: U

i = 28 VDC

Ii = 120 mA

Ci = 0 µF

Li = 5 µH Pi = 840 m

W 10. D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E OF

HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D).

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

24 VDC

CO

NTR

OL

INPU

T 1

CO

NTR

OL

INPU

T 2

APPRO

VED SAFETY

BARR

IER

APPRO

VED SAFETY

BARR

IER

LOO

P VOLTAG

E

SHIELD

SHIELD

LOO

P 1+

LOO

P 1-

LOO

P 2+

LOO

P 2-

US

SING

LE OR

DU

AL CAVITY

NEM

A HO

USIN

G

II 1/2 G Ex ia T4 Ga/GbTa = -50 TO 71°C; IP65

INTR

INSIC

ALLY SAFEFM

14ATEX0068XIEC

Ex FMG

14.0032X

2809

EARTH

GR

OU

ND

(SEE N

OTE 4)

EARTH

GR

OU

ND

(SEE N

OTE 4)

11 FOR

INSTALLATIO

N W

ITHIN

THE EU

RO

PEAN U

NIO

N, SEE EN

60079-14. 12.TH

E MAXIM

UM

PERM

ITTED AM

BIENT TEM

PERATU

RE O

F THE LEVEL PLU

S DIG

ITAL/ANALO

G

LEVEL TRAN

SMITTER

IS 71 °C. TO

AVOID

THE EFFEC

TS OF PR

OC

ESS TEMPER

ATUR

E AND

O

THER

THER

MAL EFFEC

TS CAR

E SHALL BE TAKEN

TO EN

SUR

E THE SU

RR

OU

ND

ING

AMBIEN

T AN

D TH

E AMBIEN

T INSID

E THE TR

ANSM

ITTER H

OU

SING

DO

ES NO

T EXCEED

71°C 13.C

AUTIO

N: FLEXIBLE G

AUG

ES HAVE A M

INIM

UM

BEND

RAD

IUS O

F 381MM

(15") 14. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT

METALS (ALU

MIN

UM

OR

TITANIU

M) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO AC

CO

UN

T R

ARE M

ALFUN

CTIO

N. M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS W

HEN

USIN

G TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE

NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS C

ANN

OT O

CC

UR

15.WAR

NIN

G: SU

BSTITUTIO

N O

F CO

MPO

NEN

TS MAY IM

PAIR IN

TRIN

SIC SAFETY.

16.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E PART S,

TO PR

EVENT TH

E RISK O

F ELECTR

OSTATIC

SPARKIN

G. TH

E NO

N-M

ETALLIC SU

RFAC

E SHO

ULD

ON

LY BE CLEAN

ED W

ITH A D

AMP C

LOTH

. PAINTED

SU

RFAC

E OF TH

E EQU

IPMEN

T MAY STO

RE ELEC

TRO

STATIC C

HAR

GE AN

D

BECO

ME A SO

UR

CE O

F IGN

ITION

IN APPLIC

ATION

S WITH

A LOW

RELATIVE

HU

MID

ITY <~30% R

ELATIVE HU

MID

ITY WH

ERE TH

E PAINTED

SUR

FACE IS

RELATIVELY FR

EE OF SU

RFAC

E CO

NTAM

INATIO

N SU

CH

AS DIR

T, DU

ST OR

O

IL. CLEAN

ING

OF TH

E PAINTED

SUR

FACE SH

OU

LD O

NLY BE D

ON

E WITH

A D

AMP C

LOTH

. 17.TH

E APPLICABLE TEM

PERATU

RE C

LASS, PRO

CESS TEM

PERATU

RE R

ANG

E AN

D AM

BIENT TEM

PERATU

RE R

ANG

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

TO 85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C

< TA < 71°C

NOTES


I 51 I

Fig. 57: Intrinsically Safe ATEX / IECEx installation drawing, HART®, Page 2

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

DETAIL H

SCALE 1 : 1

D

E

F

H

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651544-3LEVEL

2 2

(ACP) IN

STALLATIN D

WG

LP ANALO

G IN

TRIN

SICALLY SAFE FO

R ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).**

I


S 2/23/15D 8037 ADDED W







S 6-12-19I 8818 CHANGED NOTES 1, 14, 16, 17 DR 12-10-19

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

(2") OF H

OU

SING

.

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY & N

EMA H

OU

SING



WIRING CHART( FOR NEM

A GAUGE)


A GAUGE)

WIRE COLOR

SIGNALRED

LOOP 1+BLACK

LOOP 1-BLUE

LOOP 2-W

HITELOOP 2+

GREENN/A

DRAIN WIRE

EARTH GROUND

PIN #SIGNAL

PIN 1LOOP 1-

PIN 2LOOP 1+

PIN 3LOOP 2-

PIN 4LOOP 2+

PIN 5N/A

PIN 6EARTH GROUND


I 52 I

13.5.2 ATEX/IECEx XP



2. Cables shall be rated > 5 °C above maximum ambient temperature.


4. Equipment can be installed in a boundary wall configuration where the process connection is installed as Category 1G equipment while the transmitter housing is installed as Category 2G equipment. Refer to installation instructions.



ambient temperature range of the equipment is as follows;• T3 with Process Temperature Range of -40 °C to 150 °C• T4 with Process Temperature Range of -40 °C to 135 °C• T5 with Process Temperature Range of -40 °C to 100 °C• T6 with Process Temperature Range of -40 °C to 85 °C• Ambient Temperature Range -40 °C < Ta < 71 °C



cannot occur

Fig. 58: Flameproof, ATEX and IECEx label, Modbus or DDA Housing Option D, E, G, H, or L

Fig. 59: Flameproof, ATEX and IECEx label, HART®, Housing Option D, E, G, H, or L

FM19ATEX0179XIECEx FMG19.0037X

Level Plus TransmitterMTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513 U.S.A

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS

MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)

INSTALL PER DRAWING # 651552-3/651595-3

II 1/2 G Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP65 INPUT: 28V (120mA) maxOUTPUT: RS485

2809

P/N 551707-X Rev C

!

R

FM19ATEX0179XIECEx FMG19.0037X

Level Plus TransmitterMTS Systems CorporationSensors Division3001 Sheldon Drive, Cary, N.C. 27513U.S.A

II 1/2 G Ex db IIB+H2 T6...T3 Ga/Gb Ta = -40°C to +71°C ; IP65 INPUT: 28V (120mA) maxOUTPUT: 4-20mA

MAX. PRESSURE 1000 PSI (RIGID SENSOR)MAX. PRESSURE 435 PSI (FLEX SENSOR)

INSTALL PER DRAWING # 651553-3/651597-3

WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT. POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS

2809

P/N 551709- Rev C

!

R

13.5.2.2 Labels


I 53 I


Fig. 60: Flameproof, ATEX and IECEx Installation Drawing, Modbus and DDA, Page 1

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-3D

LEVEL1

2

(ACP) IN

STALLATION

DW

G LP AN

ALOG

EXPLOSIO

N PR

OO

F ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***




C 8716 UPDATED CE TO 2809 MS 6/13/19

D 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19

EARTH GROUND

LOOP 2-

LOOP 2+

EARTH GROUND

LOOP 1-

LOOP 1+

NO

N H

AZARD

OU

S LOC

ATION

HAZAR

DO

US LO

CATIO

N

EARTH

GR

OU

ND

LUG

NO

TE 3

AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

US

SING

LE OR

DU

AL CAVITY

2809For ATEX - FM

16ATEX0068XFor IECEx - IECEx FM

G 16.0033X

AREA R

EQU

IRIN

G

EPL Gb

AREA R

EQU

IRIN

G

EPL Ga

CO

ND

UIT JU

NC

TION

CO

ND

UIT

SEE NO

TE 1

SEE NO

TE 8

II 1/2 G Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C; IP65

CATEG

OR

Y 1

CATEG

OR

Y 2

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

SEAL ALL CO

ND

UITS W

ITHIN

50mm

(2") OF EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PREVEN

T IGN

ITION

OF FLAM

MABLE O

R C

OM

BUSTIBLE ATM

OSPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A D

AMP C

LOTH





RELATIVE HUM



ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE INSTALLED

IN TH

E BOU

ND

ARY W

ALL BETWEEN

AN EPL G

a AREA AN

D TH

E LESS H

AZARD

OU

S AREA, EPL G

b. IN TH

IS CO

NFIG

UR

ATION

, THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED

IN EPL G

a, WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

IN EPL G

b. REFER

TO IN

STALLATION

IN

STRU

CTIO

NS.

EQU

IPMEN

T CAN

BE INSTALLED

IN A BO

UN

DAR

Y WALL C

ON

FIGU

RATIO

N W

HER

E THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED AS C

ATEGO

RY 1G

EQU

IPMEN

T WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

AS C

ATEGO

RY 2G

EQU

IPMEN

T. REFER

TO IN

STALLATION

INSTR

UC

TION

S 9. TH

E APPLICABLE TEM

PERATU

RE C

LASS OF TH

E EQU

IPMEN

T, AMBIEN

T TEMPER

ATUR

E RAN

GE,

AND

MAXIM

UM

PRO

CESS TEM

PERATU

RE O

F THE EQ

UIPM

ENT IS AS FO

LLOW

S; T3 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +150°C

T4 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +135°C T5 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +100°C

T6 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +85°C AM

BIENT TEM

PERATU

RE R

ANG

E -40°CTa+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AGN

ETIC LEVEL G

AUG

E MAKE SU

RE TH

E ELECTR

ON

IC H

EAD AN

D PR

ESSUR

E BAR

RIER

HAVE A M

INIM

UM

SPACIN

G O

F 5 INC

HES. SEE IN

STALLATION

MAN

UAL FO

R D

ETAIL11. FLAM

EPATHS AR

E NO

T FOR

REPAIR

12. WH

EN EPL G

a IS REQ

UIR

ED, PAR

TS OF TH

E EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS (ALU

MIN

UM

OR

TITANIU

M)

SHALL BE PR

OTEC

TED FR

OM

IMPAC

T SO TH

AT IMPAC

T OR

FRIC

TION

SPARKS C

ANN

OT O

CC

UR

, TAKING

INTO

AC

CO

UN

T RAR

E MALFU

NC

TION

MEASU

RES TO

PREVEN

T IMPAC

T OR

FRIC

TION

SPARKS W

HEN

USIN

G TH

E EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS INC

LUD

E BUT AR

E NO

T LIMITED

TO:

M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R

5" [127mm

] Minim

um


I 54 I

Fig. 61: Flameproof, FM Installation Drawing, Modbus and DDA

DETAIL D

SCALE 3

DETAIL E

SCALE 1.60

DETAIL F

SCALE 1.2

D

E

F

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651553-3D

LEVEL2

2

(ACP) IN

STALLATION

DW

G LP AN

ALOG

EXPLOSIO

N PR

OO

F ATEX/IEC

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***




C 8716 UPDATED CE TO 2809 MS 6/13/19

D 8818 CHANGED NOTE 1, ADDED NOTE 12 DR 12-10-19

LOOP 2-

LOOP 2+

EARTH

LOOP 1-

LOOP 1+

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

(2") OF H

OU

SING

.

FIGU

RE 2

DU

AL CAVITY H

OU

SING


FIGU

RE 1

SING

LE CAVITY H

OU

SING



I 55 I

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-3C

LEVEL1

2

(ACP) IN

STALLATIN D

WG

LP DIG

ITAL

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***


B 8716 UPDATED TO CE 2809 MS 6-13-19


EARTH GROUND

24 VDC

COMM

ON-

Rx /Tx+

Rx /Tx-

EARTH GROUND

CATEGORY 1

CATEGORY 2


AGEN

CY C

ON

TRO

LLED D

RAW

ING

(ATEX/IEC). N

O C

HAN

GES W

ITHO

UT PR

IOR

AGEN

CY APPR

OVAL

EARTH TERMINAL

2809II 1/2 G Ex db IIB+H2 T6...T3 Ga/GbTa = -40°C to +71°C; IP65

For ATEX - FM16ATEX0068X

For IECEx - IECEx FMG 16.0033X

AREA REQUIRINGEPL Gb

AREA REQUIRINGEPL Ga

NO

TES:1.ALL N

ATION

AL AND

LOC

AL CO

DES AN

D R

EGU

LATION

S MU

ST BE ADH

ERED

TO W

HEN

INSTALLIN

G TH

E LEVEL SENSO

R IN

HAZAR

DO

US EN

VIRO

NM

ENTS.

SEAL ALL CO

ND

UITS W

ITHIN

50mm

(2") OF EN

CLO

SUR

E.2.D

UAL-C

AVITY ENC

LOSU

RES:

CU

STOM

ER C

ON

NEC

TION

S WILL BE M

ADE AT TER

MIN

AL BLOC

K ON

POW

ER SID

E O

F HO

USIN

G (N

OT TO

TERM

INAL BLO

CK O

N IN

TERC

ON

NEC

T BOAR

D). SEE FIG

UR

E 2 ON

PAGE 2

3. CAU

TION

: FLEXIBLE GAU

GES H

AVE A MIN

IMU

M BEN

D R

ADIU

S OF 381m

m(15")

4.WAR

NIN

G: TO

PREVEN

T IGN

ITION

OF FLAM

MABLE O

R C

OM

BUSTIBLE ATM

OSPH

ERES,

DISC

ON

NEC

T POW

ER BEFO

RE SER

VICIN

G

5.WAR

NIN

G: TH

E EQU

IPMEN

T CO

NTAIN

S NO

N-M

ETALLIC EN

CLO

SUR

E AND

PRO

CESS PAR

TS, TO PR

EVENT

THE R

ISK OF ELEC

TRO

STATIC SPAR

KING

. THE N

ON

-METALLIC

SUR

FACE AN

D PR

OC

ESS PARTS SH

OU

LD O

NLY

BE CLEAN

ED W

ITH A D

AMP C

LOTH





RELATIVE HUM



ITH A DAMP CLOTH.

6. CABLES SH

ALL BE RATED

> 5C ABO

VE MAXIM

UM

AMBIEN

T TEMPER

ATUR

E. 7. TO

MAIN

TAIN TH

E ING

RESS PR

OTEC

TION

RATIN

G O

F IP65, TEFLON

TAPE (3 WR

APS) OR

PIPE DO

PE SHALL

BE USED

. REFER

TO IN

STALLATION

INSTR

UC

TION

S.8. TH

E EQU

IPMEN

T CAN

BE INSTALLED

IN TH

E BOU

ND

ARY W

ALL BETWEEN

AN EPL G

a AREA AN

D TH

E LESS H

AZARD

OU

S AREA, EPL G

b. IN TH

IS CO

NFIG

UR

ATION

, THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED

IN EPL G

a, WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

IN EPL G

b. REFER

TO IN

STALLATION

IN

STRU

CTIO

NS.

EQU

IPMEN

T CAN

BE INSTALLED

IN A BO

UN

DAR

Y WALL C

ON

FIGU

RATIO

N W

HER

E THE PR

OC

ESS CO

NN

ECTIO

N IS IN

STALLED AS C

ATEGO

RY 1G

EQU

IPMEN

T WH

ILE THE TR

ANSM

ITTER H

OU

SING

IS INSTALLED

AS C

ATEGO

RY 2G

EQU

IPMEN

T. REFER

TO IN

STALLATIO

N IN

STRU

CTIO

NS.

9. THE APPLIC

ABLE TEMPER

ATUR

E CLASS O

F THE EQ

UIPM

ENT, AM

BIENT TEM

PERATU

RE R

ANG

E, AN

D M

AXIMU

M PR

OC

ESS TEMPER

ATUR

E OF TH

E EQU

IPMEN

T IS AS FOLLO

WS;

T3 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +150°C T4 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +135°C

T5 WITH

PRO

CESS TEM

PERATU

RE R

ANG

E OF -40°C

to +100°C T6 W

ITH PR

OC

ESS TEMPER

ATUR

E RAN

GE O

F -40°C to +85°C

AMBIEN

T TEMPER

ATUR

E RAN

GE -40°C Ta+71°C

10. WH

EN M

OU

NTIN

G O

N A M

AGN

ETIC LEVEL G

AUG

E MAKE SU

RE TH

E ELECTR

ON

IC H

EAD AN

D PR

ESSUR

E BAR

RIER

HAVE A M

INIM

UM

SPACIN

G O

F 5 INC

HES. SEE IN

STALLATION

MAN

UAL FO

R D

ETAIL11. FLAM

EPATHS AR

E NO

T FOR

REPAIR

12. W

HEN

EPL Ga IS R

EQU

IRED

, PARTS O

F THE EQ

UIPM

ENT C

ON

TAININ

G LIG

HT M

ETALS (ALUM

INU

M O

R TITAN

IUM

) SH

ALL BE PRO

TECTED

FRO

M IM

PACT SO

THAT IM

PACT O

R FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R, TAKIN

G IN

TO

ACC

OU

NT R

ARE M

ALFUN

CTIO

N. M

EASUR

ES TO PR

EVENT IM

PACT O

R FR

ICTIO

N SPAR

KS WH

EN U

SING

THE

EQU

IPMEN

T CO

NTAIN

ING

LIGH

T METALS IN

CLU

DE BU

T ARE N

OT LIM

ITED TO

: M

OU

NTIN

G TH

E PRO

BE VERTIC

ALLY N

O M

ECH

ANIC

AL AGITATIO

N SH

ALL BE USED

U

SE OF STILLIN

G W

ELLS TO M

ITIGATE EFFEC

T OF AG

ITATION

. LIM

IT RATE O

F CH

ANG

E OF LEVEL TO

VALUES SU

CH

THAT FR

ICTIO

N SPAR

KS CAN

NO

T OC

CU

R

SEE NOTE 8

CONDUIT SEALCONDUIT

SEE NOTE 1

5" [127mm

] Minim

um

Fig. 62: Flameproof, ATEX and IECEx Installation Drawing, HART®, Page 1


I 56 I


DETAIL CSCALE 3 : 1

DETAIL DSCALE 1.2

A

C

D

11

22

33

44

55

66

77

88

AA

BB

CC

DD

REV

ECO

#D

ESCR

IPTION

TITLE

SIZED

WG

NO

.R

EV

PRO

DU

CT LIN

ESC

ALE:

BYD

ATE

SHEET

OF

UN

LESS OTH

ERW

ISE SPECIFIED

TOLER

ANC

ES0 PLAC

ESM

M1 PLAC

EM

MAN

GLES

0.5

0.1

- THR

EAD D

EPTHS AR

E TO M

IN. FU

LL THD

S- D

RILL D

EPTHS AR

E TO FU

LL DIA.

- REM

OVE BU

RR

S AND

SHAR

P EDG

ES- D

O N

OT SC

ALE PRIN

T- M

ACH

INED

SUR

FACE FIN

ISH 3.2uM

[125 uIn]

PRO

PRIETAR

Y DATA

THE IN

FOR

MATIO

N AN

D D

ESIGN

(S) DISC

LOSED

HER

EIN AR

E THE PR

OPER

TY OF M

TS SYSTEMS

CO

RPO

RA TIO

N AN

D M

AY NO

T BE USED

,R

EPRO

DU

CED

OR

DISC

LOSED

IN AN

Y FOR

MEXC

EPT AS GR

ANTED

IN W

RITIN

G BY M

TSSYSTEM

S CO

RPO

RATIO

N. TH

IS RESTR

ICTIO

NEXC

LUD

ES INFO

RM

ATION

THAT IS IN

THE

PUBLIC

DO

MAIN

OR

WAS LEG

ITIMATELY IN

THE

PRIO

R PO

SSESSION

OF TH

E REC

IPIENT.

mM

TS SYSTEMS C

OR

POR

ATION

SENSO

RS D

IVISION

3001 SHELD

ON

DR

IVE, CAR

Y, NC

27513

METRIC

FIRST

ANG

LED

651552-3C

LEVEL2

2

(ACP) IN

STALLATIN D

WG

LP DIG

ITAL

DR

AWN

BY: M

S

***NO

REVISIO

NS SH

ALL BE MAD

E WITH

OU

T THE N

OTIFIC

ATION

TO APPR

OVAL AG

ENC

Y(S).***


B 8716 UPDATED TO CE 2809 MS 6-13-19



GND+24V

TX/RX-

TX/RX+

EARTH

FIGU

RE 1

SING

LE CAVITY H

OU

SING

FIGU

RE 2

DU

AL CAVITY H

OU

SING

NO

TES: 1. TH

E CU

STOM

ER SH

OU

LD C

ON

NEC

T THE O

UTSID

E GR

OU

ND

LUG

TO TH

E SAFETY EARTH

ING

GR

OU

ND

SYSTEM W

ARN

ING

: C

ON

DU

IT SEALS REQ

UIR

ED W

ITHIN

50mm

(2") OF H

OU

SING

.


Fig. 63: Flameproof, ATEX and IECEx Installation Drawing, HART®, Page 2


I 57 I

13.5.3 EC Declaration of conformity


I 58 I

UNITED STATESMTS Systems Corporation

Sensors DivisionAmericas & APAC Region

3001 Sheldon DriveCary, N.C. 27513Phone: +1 919 677-0100E-mail: [email protected]

GERMANYMTS Sensor Technologie

GmbH & Co. KGEMEA Region & India

Auf dem Schüffel 958513 LüdenscheidPhone: +49 2351 9587-0E-mail: [email protected]

ITALYBranch Offi ce

Phone: +39 030 988 3819E-mail: [email protected]

FRANCEBranch Offi ce

Phone: +33 1 58 4390-28E-mail: [email protected]

UK Branch Offi ce

Phone: +44 79 44 15 03 00E-mail: [email protected]

SCANDINAVIABranch Offi ce

Phone: + 46 70 29 91 281E-mail: [email protected]

CHINABranch Offi ce

Phone: +86 21 2415 1000 / 2415 1001E-mail: [email protected]

JAPANBranch Offi ce

Phone: +81 3 6416 1063E-mail: [email protected]

www.mtssensors.comMTS, Temposonics and Level Plus are registered trademarks of MTS Systems Corporation in the United States; MTS SENSORS and the MTS SENSORS logo are trademarks of MTS Systems Corporation within the United States. These trademarks may be protected in other countries. All other trademarks are the property of their respective owners. Copyright © 2020 MTS Systems Corporation. No license of any intellectual property rights is granted. MTS reserves the right to change the information within this document, change product designs, or withdraw products from availability for purchase without notice. Typographic and graphics errors or omissions are unintentional and subject to correction. Visit www.mtssensors.com for the latest product information.

Document Part Number: 551696 Revision G (EN) 01/2020

S a f e t y I n t e g r i t y L e v e lIEC 61508

level plus - mts sensors · 2020-03-17 · level plus ® magnetostrictive ... 6a heavy oils...

Documents