laser applications to medicine and biology
TRANSCRIPT
LASER APPLICATIONS TO MEDICINE AND
Prof. Dr. Moustafa. M. MohamedVice Dean
Faculty of Allied Medical SciencePharos University
Alexandria
Dr. Mervat Mostafa
Department of Medical Biophysics
Pharos University
FIRST OFF WHAT DOES LASER STAND FOR?
LLIGHTIGHT AAMPLIFICATION BY MPLIFICATION BY SSTIMULATED TIMULATED EEMISSION OF MISSION OF RRADIATIONADIATION
Basic Concepts: Laser is a narrow beam of light of a single
wavelength (monochromatic) in which each wave is in phase (coherent) with other near it.
Laser apparatus is a device that produce an intense concentrated, and highly parallel beam of coherent light.
Basic theory for laser (Einstein 1917):
Atom composed of a nucleus and electron cloud If an incident photon is energetic enough, it may
be absorbed by an atom, raising the latter to an excited state.
It was pointed out by Einstein in 1917 that an excited atom can be revert to a lowest state via two distinctive mechanisms: Spontaneous Emission and Stimulated Emission.
Spontaneous emission: Each electron can drop back
spontaneously to the ground state emitting photons.
Emitted photons bear no incoherent. It varies in phase from point to point and from moment to moment.
e.g. emission from tungsten lamp.
Stimulated emission: Each electron is triggered into emission by the
presence of electromagnetic radiation of the proper frequency. This is known as stimulated emission and it is a key to the operation of laser.
e.g. emission from Laser
Excited state
Ground state
hν
Absorption: Let us consider an atom that is initially in
level 1 and interacts with an electromagnetic wave of frequency n. The atom may now undergo a transition to level 2, absorbing the required energy from the incident radiation. This is well-known phenomenon of absorption.
E1
E2
h=E2 – E1
According to Boltzmann's statistics, if a sample has a large number of atoms, No, at temperature T, then in thermal equilibrium the number of atoms in energy states E1 and E2 are:N1 = No e-E
1/kT
N2 = No e-E2
/kT
If E1 < E2 Then N1 > N2
If E1 < E2 and N1 < N2 This is called "Population Inversion".
Population inversion: Generally electrons tends to (ground state).
What would happen if a substantial percentage of atoms could somehow be excited into an upper state leaving the lower state all empty? This is known as a population inversion. An incident of photon of proper frequency could then trigger an avalanche of stimulated photon- all in phase (Laser).
Consider a gas enclosed in a vessel containing free atoms having a number of energy levels, at least one of which is Metastable.
By shining white light into this gas many atoms can be raised, through resonance, from the ground state to excited states.
Population Inversion E1 = Ground state, E2 = Excited state (short life time ns), E3 = Metastable state (long life time from
ms to s).
hE1
E2
E3
10-3 -1 sec
10-9 sec
Output (amplification)
Life times
Excitation
To generate laser beam three processes must be satisfied:- Population inversion. Stimulated emission. Pumping source.
MEDIUM
PUMPMIRROR
COLLIMATEDBEAM
Pumping Sources Optical Pumping: Suitable For Liquid And Solid
Laser Because They Have Wide Absorption Bands.
Electric Pumping: Suitable For Gas Laser Because They Have Narrow Absorption Band.
Chemical Reaction.
Types of lasers According to the active material: solid-state, liquid, gas, excimer or semiconductor
lasers.
According to the wavelength: Infra-red (IR), Visible, Ultra-violet (UV) or X-ray
Lasers.
Solid-state lasers have lasing material distributed in a solid matrix (such as ruby or Nd-
YAG). Flash lamps are the most common power source. The Nd-YAG laser emits infrared light at 1.064 nm.
Semiconductor lasers, sometimes called diode lasers, are p-n junctions. Current is the pump source.
Applications: laser printers or CD players.
Types of lasers
Dye lasers use complex organic dyes, such as Rhodamine 6G, in liquid solution or suspension as lasing media. They are tunable over a broad range of wavelengths.
• Gas lasers are pumped by current. Helium- Neon (He-Ne) lasers in the visible and IR. Argon lasers
in the visible and UV. CO2 lasers emit light in the far-infrared (10.6 mm), and are used for cutting hard materials.
Types of lasers
Excimer lasers: (from the terms excited and dimers) use reactive gases, such as chlorine and fluorine, mixed with inert gases such as argon, krypton, or xenon. When electrically stimulated, a pseudo molecule (dimer) is produced. Excimers laser in the UV.
Solid-state Laser Example: Ruby Laser Operation wavelength: 694.3 nm (IR) 3 level system: absorbs green/blue Gain Medium: crystal of aluminum oxide (Al2O3)
with small part of atoms of aluminum is replaced with Cr3+ ions.
Pump source: flash lamp The ends of ruby rod serve as laser mirrors.
Ruby Laser
How Ruby laser works? 1. High-voltage electricity causes the quartz
flash tube to emit an intense burst of light, exciting some of Cr3+ in the ruby crystal to higher energy levels.
2. At a specific energy level, some Cr3+ emit photons. At first the photons are emitted in all directions. Photons from one Cr3+ stimulate emission of photons from other Cr3+ and the light intensity is rapidly amplified.
How Ruby laser works?
3. Mirrors at each end reflect the photons back and forth, continuing this process of stimulated emission and amplification
How Ruby laser works?
4. The photons leave through the partially silvered mirror at one end. This is laser light.
How Ruby laser works?
High and Low Level Lasers High Level Lasers
–Surgical Lasers –Hard Lasers –Thermal –Energy (3000-10000) mW
Low Level Lasers
–Medical Lasers –Soft Lasers –Subthermal –Energy (1-500) mW –Therapeutic (Cold) lasers produce maximum
output of 90 mW or less (600-1000) nm light
Parameters Laser
–Wavelength –Output power – Average power – Intensity –Dosage
Wavelength Nanometers (nm) Longer wavelength (lower frequency) = greater
penetration Not fully determined Wavelength is affected by power
Power Output Power–Watts or milliwatts (W or mW)–Important in categorizing laser for safety
Intensity Power Density (intensity)–W or mW/ cm2– Takes into consideration – actual beam diameter
If light spread over lager area – lower power density
– Beam diameter determines power density
Average Power Knowing average power is important in
determining dosage with pulsed laser If laser is continuous – average power = peak
output power If laser is pulsed, then average power is equal to
peak output power X duty cycle.
Energy Density Dosage (D) Amount of energy applied per unit area Measured in Joules/square cm (J/cm2) – Joule – unit of energy – 1 Joule = 1 W/sec Dosage is dependent on: –Output of laser in mW. – Time of exposure in seconds. – Beam surface area of laser in cm2
Laser Treatment & Diagnostics Treatment cover everything from the ablation of
tissue using high power lasers to photochemical reaction obtained with a weak laser.
Diagnostics cover the recording of fluorescence after excitation at a suitable wavelength and measuring optical parameters.
Laser Tissue Interaction:
What Does Laser Do? Laser light waves penetrate the skin with no
heating effect, no damage to skin & no sideeffects.
Laser light directs biostimulative light energy to the body’s cells which convert into chemical energy to promote natural healing & pain relief.
Stimulation of wound healing – Promotes faster wound healing/clotformation –Helps generate new & healthy cells & tissue
Increase collagen production –Develops collagen & muscle tissue
Increase macrophage activity – Stimulates immune system
Alter nerve conduction velocity – Stimulates nerve function
What Does Laser Do?
Improved blood circulation & vasodilation – Increases blood supply • Increases ATP production • Analgesic effect – Relieves acute/chronic pain • Anti-inflammatory & anti-edematous effects – Reduces inflammation
What Does Laser Do?
Tissue & Cellular Response Magnitude of tissue’s reaction are based on
physical characteristics of:
–Output wavelength/frequency –Density of power –Duration of treatment – Vascularity of target tissues
Direct and indirect laser effects Direct effect - occurs from absorption of photons Indirect effect – produced by chemical events caused by interaction of photons emitted from laser and the tissues
LASER Regulation Lasers are classified according to the hazard;* Class 1 and 1M (magnifier) lasers are
considered safe * Class 2 and 2M (magnifier) - emit visible light at higher levels than Class 1, - eye protection is provided- can be hazardous if the beam is viewed directly
with optical instruments;
* Class 3R (Restricted) Laser- produce visible and invisible light that are hazardous under direct viewing conditions;* Class 3B lasers- produce visible or invisible light that is hazardous under direct viewing conditions- they are powerful enough to cause eye damage in a time shorter- Laser products with power output near the upper range of Class 3B may also cause skin burns;
* Class 4 lasers- high power devices capable of causing both eye and skin burns,- heir diffuse reflections may also be hazardous- the beam may constitute a fire hazard;