lamina catalog 2016 en 06feb2017 - dallagottcdallagottc.com/.../2017/02/catalogo-lamina-2016.pdf ·...

MADE IN SWITZERLAND

PRODUCT LINE 2016

Index

Turning 17

Thread Milling 351

User Guide 3

Drilling 337

Thread Turning 193

Alu-Milling 331

Alu-Turning 161

Solid End Mills 355

Contact Information 383

Parting 177

Materials Reference List 377

Milling 203

© Lamina Technologies 2016

MADE IN SWITZERLAND

3

USER GUIDE

User Guide

4

USER GUIDE

For new users of Lamina Technologies Multi-MatTM (multi-material) inserts and to get more productivity and longer tool life, we have prepare a short machining guide to insure your satisfaction with our products.

The machining conditions included after each insert are our guidelines for optimal machining. However, our inserts can work in wide range of cutting conditions to meet special machining needs.

Check the condition of the tool holder (insert seat, shim, lever, screw) and check if the insert is well seated and clamped.

If there are interrupted cut or passes with short lengths of cut, dry operation is recommended to avoid thermal shocks. For heavy interrupted cut feed rate should be reduced.

Coolant

Check the stability of the machine. The tool overhang should be as short as possible.

Cutting speed has the greatest influence on tool life. For high productivity and long tool life, first increase d.o.c. and feed rate.

Vc

fn

d.o.c

Tool life

Cutting parameters

+

+-

-

Respect maximum chip section area for each insert. Amax = feed x d.o.c.

Feed x d.o.c.=

Amax

For higher productivity and better chip control in roughing, work close to the recommended Amax value.

Section max

[mm2]Depth of cut

[mm]

Feed

[mm/t]f maxf min

Machining Optimization

Turning

5

USER GUIDE

Climb Milling:Usually this is the recommended direction. Tool life up to 40% longer than conventional.

Vf

Conventional Milling:Recommended only for:• Old machines with backlash in the table transmission• Flame cut, forged and cast workpieces• Thin workpieces (in order to reduce vibration)Vf

Fv

К = 90° Approach angleHigh radial forces / Low axial forces.Recommended:• When 90° wall is needed• For unstable conditions• For slender workpieces

h = fz

fz

For face milling the width of cut (ae) should be about 70% of the cutter diameter, in order to achieve better chip formation and longer tool life. For limited engagement conditions, it is necessary to increase feed per tooth.

0.7 x DD

К = 45° Approach angle identical radial and axial forces. High productivity fz = 1.41 x hRecommended:• When overhang is long (lower vibration tendency)• For face milling (1st choice)

h = 0.71 x fzfz

45°

Round Inserts:Roughing and general purposes. Strongest cutting edge.

Milling

Check the condition of the tool holder (insert seat, shim, lever, screw) and check if the insert is well seated and clamped.

Check the stability of the machine. The tool overhang should be as short as possible.


6

USER GUIDE

Description

The workpiece material is welded to the cutting edge. Normally caused by low temperatures.

Built-up Edge (Adhesive Wear) Solution

• Increase cutting speed • Increase feed• Use more positive geometry

Notch wear (Adhesive/Mechanic Wear) Description

Result of adhesive or mechanical action. Chipping or localized wear at the depth of cut line.

Solution

• Use more positive geometry• Reduce feed• Vary depth of cut

Crater (Chemical Wear) Description

Happens on the rake surface. Normally the result of a combination of a diffusion and abrasion wear mechanism.

Solution

• Decrease cutting speed• Check coolant direction• Use more positive geometry

Flank Wear (Abrasive Wear) Description

Abrasive wear mechanism that happens on the cutting edge’s flank. Not common in Lamina inserts.

Solution

• Decrease cutting speed• Check coolant direction.

Plastic Deformation (Thermal Wear) Description

Caused by cutting forces and too high temperature. Not common in Lamina inserts.

Solution

• Decrease cutting speed• Decrease feed rate

Thermal Cracks (Thermal Wear) Description

Small cracks normally at 90° to the cutting edge caused by temperature variation

Solution

• Stabilize the temperature• Shut off the coolant

Breakage (Mechanic Wear) Description

Most breakages happen because the wear development is not seen in time.

Solution

• Check the tool holder• Check the tool overhang• Check the Amax• Decrease feed and Vc• Apply more robust insert• Check the run-out


7

USER GUIDE

Material Groups

1

2

3

6

4,6

5,7

8

10

10

11

11

14

14

14

14

12

13

15

15

16

17,19

17,19

18,20

31,32 Incoloy 800

33 Inconel 700

34 Stellite 21

36 TiAl6V4

37 T40

38

38

38

Chilled Cast Iron 40 Ni-Hard 2

White Cast Iron 41 G-X300CrMo15

Al (>8%Si) 12 25 AlSi12

Si < 4 %

4% < Si < 8 %

Cooper Alloys 14 26,27,28 CuZn30

29 Fiber Plastics

30 Hard Rubber

- Graphite

Non-ferrous and soft materials (less than 130HB of hardness). Most common: Aluminum

Composition: Fe-C alloy with 2.1 to 5% of carbon. It can be alloyed with Si, P, Mn and Ni. Characteristics: Grey cast iron tends to be brittle, and malleable cast irons usually have a more ductile but less homogeneous microstructure. Reinforced cutting edges will perform best. High productivity can be achieved by using high feeds.

Caution

Notch wearCrater

Built-up edge

Non-alloyed SteelComposition: Fe-C alloy (usually 0.1 to 0.6% carbon).Characteristics: Good machinability and high cutting speeds can be applied. When it has less than 0.25% carbon, it can be very sticky, requiring positive rake and small land inserts.Alloyed SteelComposition: Fe-C alloy (maximum 2.1% carbon) with additives like Cr, Mo, V, Ni, Mn, Co, W, etc. Characteristics: The variation in the amount of alloying elements and different heat treatments control features such as mechanical resistance and machinability. It's important to follow the cutting speeds recommended according to the hardness of the steel, as it influences temperature as well as chemical and adhesive wears. High alloyed Steel have more than 5% alloying elements.

Composition: Alloyed steel, more than 11% chrome (Cr).Characteristics: Stainless steels do not stain, corrode, or rust as easily as ordinary steel. Usually they are difficult to machine because of its narrow range of cutting speeds. If the cutting speed is too low, the material sticks in the cutting edge, if it’s too high, the high quantity of additives produces abrasive wears in the cutting edge.

This group includes hardened and tempered steel up to 55 HRc, chilled and white cast iron up to 55 HRc. Machining success depends largely on clamping system rigidity, as cutting forces and power consumption are high. Finishing represents the majority of the operations for this material group.

Crater

Composition: Iron (Fe) based, Nickel (Ni) based or Cobalt (Co) based alloys and Titanium alloys.Characteristics: High temperature alloys and titanium provide excellent mechanical strength resistance, as well as corrosion and oxidation resistance. Relatively low cutting speed is recommended due to their poor thermal conductivity.

Built-up edge Crater

Al (<8%Si)

NFHi

gh T

e mp.

All o

y s

Fe, Ni &Co based

9

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Composition: Al alloys can be alloyed with Cu, Zn, Mg, Mn and Si.Characteristics: Aluminium is widely used due to its low density and relatively good strength to weight ratio. When machining, it tends to have long chips and built-up edge. A highly positive cutting edge together with low friction coating control the chips and reduce built up edge.

St

eel

Material Group Gr. N°VDI

GroupMaterial

Examples*Description

Non-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6

Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

304, 316, X5CrNi18-9

Duplex 5X2CrNiN23-4,

S31500

4

Ferritic & Martensitic

6 410, X6Cr17, 17-4 PH, 430

Cast

Iron

Grey 7

Malleable & Nodular

8

Stai

nles

s St

eel

Austenitic

GG20, GG40, EN-GJL-250, No30B

15Non-Metallic

Ti based 10

GGG40, GGG70, 50005

Steel

11

21, 22 23, 24

13

Built-up edge Crater

Crater

Flank wear Crater

Mechanical cracks

Built-up edgeNotch wear

Notch wearCrater

Crater

8

USER GUIDE

Magia Premium Grades

Magia for Turning

Now with three Magia grades for turning, Lam-ina Technologies provides further options for a greater range of application, improved efficien-cy and longer tool life.

LT 1000Recommended for general usage

Multi-MatTM LT 1000 is the most versatile grade of the Magia turning line with excellent combina-tion of hardness and toughness.

It is the first choice for customers with short pro-duction runs, different machining applications and different types of workpiece materials.

LT 1005Recommended for stable conditions, moderate to high speeds, for P, K, H material groups

Increased hardness and wear resistance at high temperatures makes this grade well suited for stable conditions and higher cutting speeds.

Highly resistant to plastic deformation thus maintains high dimensional tolerance.

LT 1025Recommended for unstable conditions, moderate to low speeds, for P, M, K material groups

Increased toughness makes this grade excel-lent for unstable conditions, such as interrupted cut.

The low chemical affinity between top ceramic layer and workpiece material ensures low fric-tion and increased resistance to built-up edge development even at low cutting speeds in fac-ing applications.

Magia for Milling

Lamina Technologies’ new generation, premi-um Multi-MatTM milling grade, LT 3000, provides higher performance, more productivity, excel-lent mechanical and improved thermal shock resistance for even longer tool life.

LT 3000

Denser micro structured coating. High quality substrate.

Magia LT 3000 inserts are made from Lamina Technologies’ advanced substrate, now with a denser micro structured, smoother coating, which allows for even lower wear rates.

Progressive and predictable wear.

The new silver top layer provides more contrast on worn edges making it easy to identify which edge has been used and the level of wear de-velopment.

More flexibility. Extended application range.

With a more tolerant coating, LT 3000 permits added flexibility and a wider application range as it can be applied at higher and lower cutting speeds than LT 30.

Lamina Technologies has augmented its Magia range of premium grades with the introduction of two new optimized, multi-layer CVD grades for turning and an advanced PVD grade for milling.

9

USER GUIDE

Material Group * = 1st choice grade

High SpeedsStable Conditions

Interrupted Cut Unstable Conditions

Low Speeds Facing to Center

** LT1005 LT1005 harder

LT1000 LT1000 LT1000

LT1025 *LT1025 *LT1025 tougher

LT1005 harder

* LT1000 LT1000 LT1000

LT1025 * LT1025 * LT1025 tougher

* LT1005 LT1005 harder

LT1000 LT1000 *LT1000* LT1025 LT1025 tougher

harder

* LT1000 * LT1000 * LT1000tougher

LT1005 LT1005 LT1005 harder

* LT1000 * LT1000 * LT1000tougher

harder

* LT1000 * LT1000 * LT1000tougher

Wear Resistance X

Toughness

P

M

K

S

H

N (>8%Si)

Toughness

Hardness

LT 1000

LT 1005

LT 1025

Grade Chart

10

USER GUIDE

Negative Turning Chipbreakers

Finishing

Steels _NMP NN NX _NMG NN NM

Stainless Steels _NMP NN NX _NMG NN

_NMP NN NX _NMG NN

Cast Iron NM (Gr. 8) _NMA (Gr. 7)

High Temp Alloys

_NMG NN NM _NMAHardened Material

_NMP NN NX _NMG NNAlu (>8%Si)

Light Cut, Stable conditionsRoughing,

Unstable Conditions

Negative Turning Chipbreakers: Overview

11

USER GUIDE

Continuous cut Interrupted cut Continuous cut Interrupted cut

NX * NX _NMP NN NX sharper

_NMG NN NN NX * _NMG NN *

NM NM * _ NMG NN NM stronger

_NMP NN _NMP NN * sharper

NX * NX * NX NX *_NMG NN _NMG NN _NMG NN _NMG NN stronger

_NMG NN _NMG NN _NMG NN *(Mat Group 8) _NMG NN sharper

NM * (Mat Group 8) NM * (Mat Group 8) NM NM * (Mat Group 8)

_NMA * (Mat Group 7) _NMA * (Mat Group 7) _NMA * (Mat Group 7) _NMA * (Mat Group 7) stronger

_NMP NN _NMP NN * sharper

NX * NX * NX NX * _NMG NN _NMG NN _NMG NN _NMG NN stronger

_NMG NN _NMG NN _NMG NN * _NMG NN sharper

NM * NM * NM NM *_NMA _NMA stronger

_NMP NN _NMP NN sharper

NX * NX NX * NX

_NMG NN _NMG NN * _NMG NN _NMG NN * stronger

NEGATIVE TURNING CHIPBREAKERS

Medium / Roughing Finishing

Material Group

* = 1st choice

Sharper edge X

Stronger edge

P

M

K

S

H

N (>8%Si)

_NMP NN

_NMA(Cast Iron Mat Group 7)

ALU(Aluminium <8% Si)

Light Cut,Stable Conditions

Roughing,Unstable Conditions

Additional dedicated geometries

Multi-MatTM Chipbreakers

NX _NMG NN NM

_NMA ALU

Negative Turning Chipbreakers: Recommendations

12

USER GUIDE

Special Design

A N

P

R

T

W

X

B

F

G

H

M

70°- 90°

70°- 90°

40°- 60°

40°- 60°

Type Symbol SymbolType

4. Fixing and Chipbreaker Types

2. Clearance Angle

A

B

C

D

E

F

G

N

P

O

Letter Symbol

3°

5°

7°

15°

20°

25°

30°

0°

11°

Special

g

A B C D

H K L

O P R

S T V W

G

M

1. Insert Shape

85° 82° 80° 55°

55°

86°

35°80°

D M S

A ± 0.005 ± 0.025± 0.025

C ± 0.025 ± 0.013 ± 0.025

E ± 0.025 ± 0.025 ± 0.025

F ± 0.013 ± 0.005 ± 0.025

G ± 0.025 ± 0.025 ± 0.130

H ± 0.013 ± 0.013 ± 0.025

± 0.025± 0.005± 0.05-0.15J*

± 0.025± 0.013± 0.05-0.15K*

± 0.025± 0.025± 0.05-0.15L*

± 0.130± 0.05-0.15 ± 0.08-0.20M*

± 0.025± 0.05-0.15 ± 0.08-0.20N*

± 0.08-0.25 ± 0.130± 0.13-0.38U*

3. Tolerance Class

Symbol

Ød

m

m

Ød

s

*Depending on the insert size. For exact tolerance see insert page.

dms

(mm)(mm)(mm)

m

Ød

A1

P22

K33

T44

W1

N22

M33

G44

Insert Designation (based on ISO norms)

13

USER GUIDE

1655

0466

PD77

T88

R99 10

Disregarding any decimals e.g. 12,7 = 12

L

L

L

L

L

L

L L

A, B, K C, D, E, M, V H, O, P

L R S

T W

5. Cutting Edge Length

R

00

M0

010204081216etc

= Sharp corner or round insert (inch version) = Round insert (metric version)

= 0.1 mm= 0.2 mm= 0.4 mm= 0.8 mm= 1.2 mm= 1.6 mm

7. Insert Corner Radius1st letter (Milling)

2nd letter (Milling)

ADEFPZ

ABCDEFGNPZ

= 45°= 60°= 75°= 85°= 90°= other

= 3°= 5°= 7°= 15°= 20°= 25°= 30°= 0°= 11°= other

6. Insert Thickness

SSS

01 = 1.59

T1 = 1.98

02 = 2.38

03 = 3.18

T3 = 3.97

04 = 4.76

05 = 5.56

06 = 6.35

07 = 7.94

09 = 9.52

S

Symbol mm

9. Cutting Direction

0855

0466

0877 88 99

NN10

e.g. Application (Milling)

- 45

- 90

- HF

45° Approach Angle90° Approach AngleHigh Feed

===

Optional information

10. Internal Designation

e.g. Chipbreaker (Turning)


NN

NM

NX

PP

ALU

General purpose

Roughing operations

General purpose Magia

All purpose grooving

Non-ferrous materials

=====

R

L

N


Turning

R

L

N


Milling


F

E

T

S

8. Edge Preparation

14

USER GUIDE

In order to obtain the best productivity using Lamina Technologies cutting tools, we have included some relevant comments and tips.

Each comment is represented by an icon and the relevant icons appear for each insert.

In machining stainless steel, please verify and respect the cutting speed recommended for the insert as there is a tendency to machine at speeds that are too low.

Stainless Steel

VC

In machining stainless steel or exotic materials, P geometry inserts (CNMP, TNMP, WNMP) and NX chipbreakers are recommended as first choice.

NX-CNMP-TNMP-WNMP

Stainless SteelExotic Material

In machining exotic materials, it is important to verify cutting conditions of the specific insert.

Exotic Material

Cutting Conditions!Verify

When milling materials from groups 1, 2, 3, 4, 6, 7, 8 and 11, coolant is not recommended. When machining materials from groups 5, 9, 10 and 12, it is recommended to use coolant.

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

To increase machining productivity, it is recommended to increase speed (Vc) while respecting chip size calculation.F

Productivity

VC

Productivity

To increase machining productivity, it is recommended to increase speed (Vc) while respecting chip size calculation.

Appropriate for boring operations.

It is important to verify and respect Amax, which is the maximum chip sec-tion. Feed x d.o.c. must be lower than the number noted as Amax.

Feed x d.o.c.=

Amax

P geometry inserts (CNMP, TNMP, WNMP) and NX chipbreakers are not recommended when machining with interrupted cut.

NXCNMPTNMPWNMP

Machining Recommendations

15

USER GUIDE

Symbol Designation Unit

Machining diameter mm

mm/rev

Machining length mm

Rotation rev/min

cm3/minChip removal rate

d.o.c x feed mm2

Nose radius mm

Dm

fn

lm

n

Q

Amax

r

Tc

Rmax

Cutting time

Surface roughness

min

μm

Feed per revolution

Vc Cutting speed m/min

ap Depth of cut (d.o.c.) mm

aeRadial depth of cut(width of cut) mm

D Cutter diameter mm

fz Feed per tooth mm/tooth

pcsZc

Vf Table Feed mm/min

pcsZn

Symbol Designation Unit

VcQ = x ap x fn

Vc =Dm x x n

1000

n =Vc x 1000

Dm x

Tc =lm

fn x n

Rmax = fn

2

x 125r

SurfaceRoughness(μm)

Cutting Time(min)

Rotation(Rev/min)

CuttingSpeed(m/min)

Chip RemovalRate(cm3/min)

Turning

fz =

Vcn =x 1000

x D

Vc = n x x D

1000

Q =ae x ap x Vf

1000

Vf = n x zc x fz

Feed per Tooth

Rotation(Rev/min)

CuttingSpeed(m/min)

Table Feed(mm/min)

Cutting Output(cm3/min)

Millling

Vf

n x zc

Total number of teeth

Effective number of teeth

Technical Formulas

16

USER GUIDE

Is it true that Lamina Technologies’ inserts can be used with any type of working material?

Lamina inserts have been tested in countless applications around the world and are suitable for practically any type of turning or milling metal cutting operation.

While Lamina inserts will work in aluminum pro-duction jobs, aluminum frequently requires tai-lored chip-control optimization. Please see Lam-ina’s dedicated aluminium line of inserts.

What speeds and feeds should Lamina inserts be run at?

In this catalog specific recommendations are provided for each individual insert indicating the speeds and feeds that are required for most of the material groups.

In order to achieve the maximum advantage from Lamina’s grade technology, it is important to always run the inserts according to the rec-ommended conditions.

In general, the best results are normally achieved at the high range of the recommended cutting speeds.

What can we expect regarding the quality and consistency of Lamina inserts?

Due to Lamina’s unique production methods and quality control procedures, you can expect inserts with higher accuracy and consistency than you have been accustomed up to now; in-sert to insert, box to box and batch to batch.

What percentage of my tooling requirements can Lamina supply?

In most regular shops, Lamina’s inserts program should cover about 80% of all inserts needed for CNC machines from 20 Hp and down. The insert program covers a full range of standard turning and milling operations from semi-roughing to su-per-finishing.

Will Lamina grades perform better than the specialized and dedicated grades available from the market?

Lamina has extensive know-how in sub-micron powder technology as well as in state of the art PVD coating. This know–how combined with unique chipbreaker geometry and in depth un-derstanding of the industry, enables Lamina to offer the Multi-MatTM Concept; a simple concept of using one insert to work on many materials.

The same insert can be used on the next job and the job after and so on, replacing the hun-dreds of specialized and confusing insert choic-es that are being used.

In machine shops that run Lamina inserts, what do they find as the biggest benefits?

• Time saving - Always have the right insert available for any job. This reduces the number of setups and idle time.• Cost saving - 80% reduction in insert inventory, ordering and stocking cost.

What about turning tool holders and boring bars?

Lamina’s ANSI / ISO standard turning inserts are designed to fit all industrial standard turning tools and boring bars, using the tool holders you have in your stock.

How does the 4 corners Alu-Line perform in low silicon aluminum?

Our Alu-Line insert’s geometry is specially de-signed for aluminum with low silicon content, creating chips that break instead of curl. The inserts are also coated and treated to reduce friction achieving unbeatable performance and tool life.

What is special about your solid end mill line?

Lamina know-how was applied to the solid end mill line. Our mills generate less friction and heat and therefore give better cut and longer tool life.

Frequently Asked Questions

17

TURNING

LT 10 | 1000LT 1005 | LT 1025

TURNING

CCMT

18

TURNING

Finishing: (F)d.o.c. =

fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev

Roughing: (R)d.o.c. =

fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev

= Not recommended= Good = Acceptable

Details on page 14

Machining Recommendations Application Guide

LT 10 and LT 1000 LT 10 and LT 1000

Stainless Steel

VC

F M R

Application Guide

Insert Designation s r Catalog Nr.l

LT 10 Multi-MatTM General Usage – Standard

T00017761.204.7612CCMT 120412 NN LT 10

T00014570.804.7612CCMT 120408 NN LT 10

T00014560.404.7612CCMT 120404 NN LT 10

T00001170.803.979CCMT 09T308 NN LT 10

T00000560.403.979CCMT 09T304 NN LT 10

T00000550.402.386CCMT 060204 NN LT 10

TURNING

C C M T80° 7°

Shape Clearance Anglel

m

Tolerance

Ø d

s ± 0.13For l = 06/09, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13

Fixing, Chipbreaker

s

F M R

Application Guide


LT 1000 Multi-MatTM General Usage – Premium

T00018931.20 4.7612CCMT 120412 NN LT 1000

T00018920.804.7612CCMT 120408 NN LT 1000

T00018910.404.7612CCMT 120404 NN LT 1000

T00018900.803.979CCMT 09T308 NN LT 1000

T00018890.403.979CCMT 09T304 NN LT 1000

T00018880.402.386CCMT 060204 NN LT 1000

80° diamond shape inserts with positive chipbreaker geometry. Very popular and useful for boring (even of small diameters), facing and external turning operations.

NN Chipbreaker

19

TURNINGMachining Conditions

min mmax min mmax min mmax D.O.C. FFeed Vcc

1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300

2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260

3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240

6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260

4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240

5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200

8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180

10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180

10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140

11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120

11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110

14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260

14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210

14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140

14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140

12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240

13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180

15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240

15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220

16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200

17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240

17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220

18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180

31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335

36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660

37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550

38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990

38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880

38 55 HRc 0.0 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.3 1.1 0.04 0.10 0.11 40 60 00.6 0.08 550

White Cast Iron 41 G-X300CrMo15 55 HRc 0.3 1.0 0.04 0.08 0.08 30 50 00.5 0.05 440

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500

Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430

Cast

Iron

Grey 7 GG20, GG40, EN-GJL-250,

No30B

Malleable & Nodular 8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel

Austenitic 4304, 316,

X5CrNi18-9

Duplex 5

Feed [mm/rev] Vc [m/min] Suggested Starting Parameters

St

eel


Low alloyed

D.O.C. [mm]

2


GroupMaterial Examples* Hardness

CCMT 060204 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

Material Group Gr. N° VDIGroup

Material Exemples Hardness

D.O.C [mm] Feed [mm/rev] Amax[mm2]

Vc [m/min] Suggested Starting Parameters

min max min max min max D.O.C Feed Vc

20

TURNING Machining Conditions

min max min max min max D.O.C. Feed

1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


CCMT 09T304 NN – LT 10 | LT 1000


GroupMaterial

ExemplesHardness


Vc [m/min]Suggested Starting

Parameters


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






21


1 125 HB 0.5 4.0 0.2 0.5 2 180 330 22.7 0.3 2240

2 190 HB 0.5 4.0 0.2 0.5 2 180 280 22.7 0.3 2220

3 250 HB 0.5 4.0 0.2 0.5 1 180 250 22.7 0.3 2200

6 180 HB 0.5 4.0 0.2 0.5 1 120 280 22.7 0.3 2200

4,6 230 HB 0.5 3.2 0.2 0.5 1 120 250 22.7 0.3 1180

5,7 280 HB 0.5 3.2 0.2 0.4 1 120 210 22.7 0.3 1150

8 350 HB 0.5 2.8 0.2 0.4 1 120 180 22.7 0.3 1130

10 220 HB 0.5 3.2 0.2 0.4 1 70 190 22.3 0.3 1140

10 280 HB 0.5 3.2 0.2 0.4 1 70 150 22.3 0.3 1120

11 320 HB 0.5 2.4 0.2 0.4 1 70 130 22.3 0.3 1100

11 350 HB 0.5 2.4 0.2 0.4 1 70 110 22.3 0.3 990

14 180 HB 0.5 4.0 0.2 0.4 1 170 270 22.7 0.2 1190

14 240 HB 0.5 4.0 0.2 0.4 1 160 220 22.7 0.2 1170

14 290 HB 0.5 3.2 0.2 0.4 1 80 150 22.3 0.2 1100

14 310 HB 0.5 3.2 0.2 0.4 1 70 140 22.3 0.2 990

12 200 HB 0.5 4.0 0.2 0.4 1 170 250 22.3 0.2 1190

13 42 HRc 0.5 3.2 0.2 0.4 1 120 190 22.0 0.2 1130

15 150 HB 0.5 4.0 0.2 0.6 2 170 250 22.7 0.3 2200

15 200 HB 0.5 4.0 0.2 0.6 2 160 230 22.7 0.3 1180

16 250 HB 0.5 4.0 0.2 0.6 2 150 210 22.7 0.3 1160

17,19 150 HB 0.5 4.0 0.2 0.5 1 120 250 22.7 0.3 1180

17, 19 200 HB 0.5 4.0 0.2 0.5 1 120 230 22.7 0.3 1160

18,20 250 HB 0.5 4.0 0.2 0.5 1 120 190 22.7 0.3 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.2 0.4 1 30 50 11.8 0.3 332

33 Inconel 700 250 HB 0.5 2.4 0.2 0.4 1 30 50 11.8 0.3 330

34 Stellite 21 350 HB 0.5 2.4 0.2 0.4 1 20 40 11.8 0.3 228

37 T40 - 0.5 2.4 0.2 0.4 1 40 60 11.8 0.3 445

36 TiAI6V4 - 0.5 3.2 0.2 0.4 1 50 70 11.8 0.3 555

41 55 HRc 0.5 1.2 0.1 0.2 0 30 50 00.9 0.1 440

40 400 HB 0.5 1.6 0.1 0.3 0 40 60 11.4 0.2 550

38 45 HRc 0.5 2.0 0.1 0.3 1 50 100 11.8 0.2 880

38 Ni-Hard 2 50 HRc 0.5 1.6 0.1 0.3 0 40 90 11.4 0.2 770

38 G-X300CrMo15 55 HRc 0.5 1.2 0.1 0.2 0.3 40.0 80.0 00.9 0.2 660

12 25 AlSi12 130 HB 0.5 4.8 0.2 0.6 2 200 400 2.7 0.4 280

X100CrMo13, 440C,

G-X260NiCr42

410, X6Cr17, 17-4 PH, 430

GG20, GG40, EN-GJL-250, N030B

GGG40, GGG70, 50005

11

C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrM0V5, H13, M42, D3, S6-5-2,

12Ni19

304, 316, X5CrNi18-9

X2CrNiN23-4, S31500

8

9

10

6

7

4

5

3

1

2

CCMT 09T308 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






22



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

CCMT 120404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






23



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

St

eel

Non-alloyed

Low alloyed

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

CCMT 120408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






24



1 125 HB 0.5 5.0 0.21 0.60 2.16 180 330 33.0 0.42 2240

2 190 HB 0.5 5.0 0.21 0.60 2.16 180 280 33.0 0.42 2220

3 250 HB 0.5 5.0 0.21 0.54 1.80 180 250 33.0 0.42 2200

6 180 HB 0.5 5.0 0.21 0.54 1.44 120 280 33.0 0.38 2200

4,6 230 HB 0.5 4.0 0.21 0.54 1.44 120 250 33.0 0.38 1180

5,7 280 HB 0.5 4.0 0.18 0.48 1.44 120 210 33.0 0.36 1150

8 350 HB 0.5 3.5 0.18 0.48 1.20 120 180 33.0 0.36 1130

10 220 HB 0.5 4.0 0.18 0.48 1.44 70 190 22.5 0.36 1140

10 280 HB 0.5 4.0 0.18 0.48 1.44 70 150 22.5 0.36 1120

11 320 HB 0.5 3.0 0.18 0.42 0.96 70 130 22.5 0.34 1100

11 350 HB 0.5 3.0 0.18 0.42 0.96 70 110 22.5 0.34 990

14 180 HB 0.5 5.0 0.20 0.48 1.44 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.48 1.20 160 220 33.0 0.35 1170

14 290 HB 0.5 4.0 0.18 0.42 0.96 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.42 0.96 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.48 1.20 170 250 33.0 0.35 1190

13 42 HRc 0.5 4.0 0.22 0.48 1.20 120 190 22.5 0.35 1130

15 150 HB 0.5 5.0 0.15 0.72 2.40 170 250 33.0 0.42 2200

15 200 HB 0.5 5.0 0.15 0.72 2.16 160 230 33.0 0.42 1180

16 250 HB 0.5 5.0 0.15 0.66 2.16 150 210 33.0 0.42 1160

17,19 150 HB 0.5 5.0 0.15 0.60 1.80 120 250 33.0 0.36 1180

17,19 200 HB 0.5 5.0 0.15 0.60 1.56 120 230 33.0 0.36 1160

18,20 250 HB 0.5 5.0 0.15 0.60 1.44 120 190 33.0 0.36 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.42 0.84 25 45 22.0 0.30 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.42 0.84 25 45 22.0 0.30 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.42 0.84 23 40 22.0 0.30 228

36 TiAl6V4 - 0.5 4.0 0.20 0.48 0.96 45 65 22.0 0.35 555

37 T40 - 0.5 3.0 0.20 0.42 0.84 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.36 0.72 50 100 22.0 0.30 880

38 50 HRc 0.5 2.0 0.11 0.30 0.48 40 90 11.5 0.24 770

38 55 HRc 0.5 1.5 0.11 0.24 0.36 40 80 11.0 0.22 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.72 2.20 200 400 3.0 0.48 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

CCMT 120412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


25

TURNING

VC

Productivity

FProductivity

C N M A80° 0°

Shape Clearance Angles

Ø d

l

m

Toleranced ± 0.08m ± 0.13s ± 0.13

Fixing,Chipbreaker

Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring opera-tions.

F M RInsert Designation s r Catalog Nr.l

LT 1005 Recommended for moderate to high speed

T00040511.24.7612CNMA 120412 LT 1005

T00040500.84.7612CNMA 120408 LT 1005

Application Guide

CNMA

26


CNMA 120408 – LT 1005

CNMA 120412 – LT 1005

min max min max min max D.O.C. Feed Vc

15 150 HB 0.7 6.0 0.20 0.60 1.7 270 450 33.5 0.40 3350

15 200 HB 0.7 6.0 0.20 0.58 1.5 200 320 33.5 0.40 2250

16 250 HB 0.7 6.0 0.20 0.56 1.5 170 240 33.5 0.40 2220

17,19 150 HB 0.7 6.0 0.20 0.52 1.3 130 260 33.0 0.30 2240

17,19 200 HB 0.7 6.0 0.20 0.50 1.1 130 230 33.0 0.30 2210

18,20 250 HB 0.7 6.0 0.20 0.48 1.0 130 190 33.0 0.30 1180



GGG40, GGG70, 50005

Amax [mm ]

Gr. N°VDI


7 GG20, GG40, EN-GJL-250,

No30B

8


15 150 HB 0.7 6.0 0.20 0.40 1.4 270 450 33.5 0.32 3350

15 200 HB 0.7 6.0 0.20 0.38 1.2 200 320 33.5 0.32 2250

16 250 HB 0.7 6.0 0.20 0.36 1.2 170 240 33.5 0.32 2220

17,19 150 HB 0.7 6.0 0.20 0.40 1.0 130 260 22.5 0.30 2240

17,19 200 HB 0.7 6.0 0.20 0.38 0.9 130 230 22.5 0.30 2210

18,20 250 HB 0.7 6.0 0.20 0.36 0.8 130 190 22.5 0.30 1180



GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters







Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


27

TURNING

LT 10 and LT 1000

NX LT 10 and LT 1000 NX LT 10 and LT 1000

LT 10 and LT 1000

NX-CNMP-TNMP-WNMP

Stainless SteelExotic Material Exotic Material


FProductivity

Stainless Steel

VC

C N M G80° 0°


m

Toleranced ± 0.08m ± 0.13s ± 0.13

Ø d

Fixing,Chipbreaker

ss



T00000611.204.7612CNMG 120412 NN LT 10

T00019660.804.7612CNMG 120408 NM LT 10

T00000590.804.7612CNMG 120408 NN LT 10

T00004910.404.7612CNMG 120404 NN LT 10

Application Guide

F M R

Application Guide



T00018971.204.7612CNMG 120412 NN LT 1000

T00027410.804.7612CNMG 120408 NX LT 1000

T00019680.804.7612CNMG 120408 NM LT 1000

T00018960.804.7612CNMG 120408 NN LT 1000

T00018950.404.7612CNMG 120404 NN LT 1000

The most popular general purpose turning inserts. Use for turning, facing and boring operations.

NX chipbreaker NM chipbreaker NN chipbreaker

NN chipbreaker

CNMG

28

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


F M R

Application Guide


T00040561.204.7612CNMG 120412 NN LT 1005

T00040550.804.7612CNMG 120408 NX LT 1005

T00040530.804.7612CNMG 120408 NM LT 1005

T00040540.804.7612CNMG 120408 NN LT 1005


F M R

Application Guide


T00041141.204.7612CNMG 120412 NN LT 1025

T00041130.804.7612CNMG 120408 NX LT 1025

T00041110.804.7612CNMG 120408 NM LT 1025

T00041120.804.7612CNMG 120408 NN LT 1025

LT 1025 Recommended for moderate to low speed

NX for LT 1025 LT 1005

NX-CNMP-TNMP-WNMP

Stainless SteelExotic Material VC

Productivity

The most popular general purpose turning inserts. Use for turning, facing and boring operations.

NX chipbreaker NM chipbreaker NN chipbreaker

C N M G

29



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

CNMG 120404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






30


1 125 HB 0.5 5.0 0.2 0.5 1.8 180 330 33.0 0.4 2240

2 190 HB 0.5 5.0 0.2 0.5 1.8 180 280 33.0 0.4 2220

3 250 HB 0.5 5.0 0.2 0.5 1.5 180 250 33.0 0.3 2200

6 180 HB 0.5 5.0 0.2 0.5 1.2 120 280 33.0 0.3 2200

4,6 230 HB 0.5 4.0 0.2 0.5 1.2 120 250 33.0 0.3 1180

5,7 280 HB 0.5 4.0 0.2 0.4 1.2 120 210 33.0 0.3 1150

8 350 HB 0.5 3.5 0.2 0.4 1.0 120 180 22.7 0.3 1130

10 220 HB 0.5 4.0 0.2 0.4 1.2 70 190 22.5 0.3 1140

10 280 HB 0.5 4.0 0.2 0.4 1.2 70 150 22.5 0.3 1120

11 320 HB 0.5 3.0 0.2 0.4 0.8 70 130 22.2 0.3 1100

11 350 HB 0.5 3.0 0.2 0.4 0.8 70 110 22.2 0.3 990

14 180 HB 0.5 5.0 0.2 0.4 1.2 170 270 33.0 0.3 1190

14 240 HB 0.5 5.0 0.2 0.4 1.0 160 220 33.0 0.2 1170

14 290 HB 0.5 4.0 0.2 0.4 0.8 80 150 22.5 0.2 1100

14 310 HB 0.5 4.0 0.2 0.4 0.8 70 140 22.5 0.2 990

12 200 HB 0.5 5.0 0.2 0.4 0.7 170 250 22.5 0.2 1190

13 42 HRc 0.5 4.0 0.2 0.4 0.7 120 190 22.2 0.2 1130

15 150 HB 0.5 5.0 0.2 0.6 2.0 170 250 33.0 0.4 2200

15 200 HB 0.5 5.0 0.2 0.6 1.8 160 230 33.0 0.4 1180

16 250 HB 0.5 5.0 0.2 0.6 1.8 150 210 33.0 0.4 1160

17,19 150 HB 0.5 5.0 0.2 0.5 1.5 120 250 33.0 0.3 1180

17, 19 200 HB 0.5 5.0 0.2 0.5 1.3 120 230 33.0 0.3 1160

18,20 250 HB 0.5 5.0 0.2 0.5 1.2 120 190 33.0 0.3 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.2 0.4 0.7 30 50 22.0 0.3 332

33 Inconel 700 250 HB 0.5 3.0 0.2 0.4 0.7 30 50 22.0 0.3 330

34 Stellite 21 350 HB 0.5 3.0 0.2 0.4 0.7 20 40 22.0 0.3 228

37 T40 - 0.5 3.0 0.2 0.4 0.7 40 60 22.0 0.3 445

36 TiAI6V4 - 0.5 3.5 0.2 0.4 0.8 50 70 22.0 0.3 555

41 55 HRc 0.5 1.5 0.1 0.2 0.3 30 50 11.0 0.2 440

40 400 HB 0.5 2.0 0.1 0.3 0.4 40 60 11.5 0.2 550

38 45 HRc 0.5 2.5 0.1 0.3 0.6 50 100 22.0 0.3 880

38 Ni-Hard 2 50 HRc 0.5 2.0 0.1 0.3 0.4 40 90 11.5 0.2 770

38 G-X300CrMo15 55 HRc 0.5 1.5 0.1 0.2 0.3 40.0 80.0 11.0 0.2 660

12 25 AlSi12 130 HB 0.5 6.0 0.2 0.6 1.8 200 400 3.0 0.4 280

3X40CrM0V5, H13, M42, D3, S6-5-2,

12Ni19

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

6410, X6Cr17, 17-4

PH, 430

7GG20, GG40, EN-GJL-250, N030B

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

X100CrMo13, 440C,

G-X260NiCr42 11

8GGG40, GGG70,

50005

9

10

CNMG 120408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






31


CNMG 120408 NN – LT 1005


1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

32


CNMG 120408 NN – LT 1025


1 125 HB 0.5 5.0 0.21 0.50 1.8 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.8 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.5 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.2 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.2 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.2 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.0 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.2 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.2 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.8 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.8 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

33



1 125 HB 0.5 5.0 0.21 0.65 2.70 180 330 44.0 0.50 2210

2 190 HB 0.5 5.0 0.21 0.65 2.70 180 280 44.0 0.50 2200

3 250 HB 0.5 5.0 0.21 0.59 2.25 180 250 44.0 0.50 2200

6 180 HB 0.5 5.0 0.21 0.59 1.80 120 280 44.0 0.44 1160

4,6 230 HB 0.5 4.0 0.21 0.59 1.80 120 250 44.0 0.44 1150

5,7 280 HB 0.5 4.0 0.18 0.52 1.80 120 210 44.0 0.38 1140

8 350 HB 0.5 3.5 0.18 0.52 1.60 120 180 44.0 0.38 1130

10 220 HB 0.5 4.0 0.18 0.52 1.80 70 190 33.3 0.38 1120

10 280 HB 0.5 4.0 0.18 0.52 1.80 70 150 33.3 0.38 1110

11 320 HB 0.5 3.0 0.18 0.46 1.20 70 130 33.3 0.35 1100

11 350 HB 0.5 3.0 0.18 0.46 1.20 70 110 33.3 0.35 990

14 180 HB 0.5 5.0 0.20 0.52 1.80 170 270 44.0 0.38 1190

14 240 HB 0.5 5.0 0.20 0.52 1.60 160 220 44.0 0.38 1170

14 290 HB 0.5 4.0 0.18 0.46 1.20 80 150 33.3 0.32 1100

14 310 HB 0.5 4.0 0.18 0.46 1.20 70 140 33.3 0.32 990

12 200 HB 0.5 5.0 0.22 0.52 1.60 170 250 44.0 0.38 1190

13 42 HRc 0.5 4.0 0.22 0.52 1.60 120 190 33.5 0.38 1130

15 150 HB 0.5 5.0 0.15 0.78 3.00 170 250 44.0 0.44 1180

15 200 HB 0.5 5.0 0.15 0.78 2.70 160 230 44.0 0.44 1170

16 250 HB 0.5 5.0 0.15 0.72 2.70 150 210 44.0 0.44 1160

17,19 150 HB 0.5 5.0 0.15 0.65 2.25 120 250 44.0 0.38 1150

17,19 200 HB 0.5 5.0 0.15 0.65 1.95 120 230 44.0 0.38 1140

18,20 250 HB 0.5 5.0 0.15 0.65 1.80 120 190 44.0 0.38 1130

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.46 1.05 25 45 22.7 0.35 330

33 Inconel 700 250 HB 0.5 3.0 0.20 0.46 1.05 25 45 22.7 0.35 332

34 Stellite 21 350 HB 0.5 3.0 0.20 0.46 1.05 23 40 22.7 0.35 228

36 TiAl6V4 - 0.5 4.0 0.20 0.52 1.20 45 65 22.7 0.38 555

37 T40 - 0.5 3.0 0.20 0.46 1.05 35 55 22.7 0.36 445

38 45 HRc 0.5 2.5 0.11 0.39 0.90 50 100 22.7 0.31 880

38 50 HRc 0.5 2.0 0.11 0.33 0.60 40 90 22.0 0.25 770

38 55 HRc 0.5 1.5 0.11 0.26 0.45 40 80 11.5 0.23 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.78 2.70 200 400 4.0 0.50 280

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

CNMG 120408 NM – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






34


CNMG 120408 NM – LT 1005


1 125 HB 0.5 5.0 0.21 0.65 2.70 180 430 33.6 0.46 2265

2 190 HB 0.5 5.0 0.21 0.65 2.70 180 365 33.6 0.42 2240

3 250 HB 0.5 5.0 0.21 0.59 2.25 180 325 33.6 0.40 2220

6 180 HB 0.5 5.0 0.21 0.59 1.80 120 365 33.6 0.38 2220

4,6 230 HB 0.5 4.0 0.21 0.59 1.80 120 325 33.6 0.38 2200

5,7 280 HB 0.5 4.0 0.18 0.52 1.80 120 275 33.6 0.36 1165

8 350 HB 0.5 3.5 0.18 0.52 1.50 120 235 33.2 0.36 1145

10 220 HB 0.5 4.0 0.18 0.52 1.80 70 245 33.0 0.36 1155

10 280 HB 0.5 4.0 0.18 0.52 1.80 70 195 33.0 0.36 1130

11 320 HB 0.5 3.0 0.18 0.46 1.20 70 170 22.6 0.34 1110

11 350 HB 0.5 3.0 0.18 0.46 1.20 70 145 22.6 0.34 1100

15 150 HB 0.5 5.0 0.15 0.78 3.00 170 325 33.6 0.42 2220

15 200 HB 0.5 5.0 0.15 0.78 2.70 160 300 33.6 0.42 2200

16 250 HB 0.5 5.0 0.15 0.72 2.70 150 275 33.6 0.42 1175

17,19 150 HB 0.5 5.0 0.15 0.65 2.25 120 325 33.6 0.36 2200

17,19 200 HB 0.5 5.0 0.15 0.65 1.95 120 300 33.6 0.36 1175

18,20 250 HB 0.5 5.0 0.15 0.65 1.80 120 245 33.6 0.36 1155

38 45 HRc 0.5 2.5 0.11 0.39 0.90 50 130 22.4 0.30 990

38 50 HRc 0.5 2.0 0.11 0.33 0.60 40 115 11.8 0.24 775

38 55 HRc 0.5 1.5 0.11 0.26 0.45 40 105 11.2 0.22 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

CNMG 120408 NM – LT 1025


1 125 HB 0.5 5.0 0.21 0.65 2.7 90 330 44.0 0.50 2210

2 190 HB 0.5 5.0 0.21 0.65 2.7 90 280 44.0 0.50 2200

3 250 HB 0.5 5.0 0.21 0.59 2.3 90 250 44.0 0.50 2200

6 180 HB 0.5 5.0 0.21 0.59 1.8 60 280 44.0 0.44 1160

4,6 230 HB 0.5 4.0 0.21 0.59 1.8 60 250 44.0 0.44 1150

5,7 280 HB 0.5 4.0 0.18 0.52 1.8 60 210 44.0 0.38 1140

8 350 HB 0.5 3.5 0.18 0.52 1.6 60 180 44.0 0.38 1130

10 220 HB 0.5 4.0 0.18 0.52 1.8 35 190 33.3 0.38 1120

10 280 HB 0.5 4.0 0.18 0.52 1.8 35 150 33.3 0.38 1110

11 320 HB 0.5 3.0 0.18 0.46 1.2 35 130 33.3 0.35 1100

11 350 HB 0.5 3.0 0.18 0.46 1.2 35 110 33.3 0.35 990

12 200 HB 0.5 5.0 0.22 0.52 1.6 85 250 44.0 0.38 1190

13 42 HRc 0.5 4.0 0.22 0.52 1.6 60 190 33.5 0.38 1130

17,19 150 HB 0.5 5.0 0.15 0.65 2.3 60 250 44.0 0.38 1150

17,19 200 HB 0.5 5.0 0.15 0.65 2.0 60 230 44.0 0.38 1140

18,20 250 HB 0.5 5.0 0.15 0.65 1.8 60 190 44.0 0.38 1130

8GGG40, GGG70,

50005

410, X6Cr17, 17-4 PH, 430

6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s


Cast

Iron Malleable

& Nodular

35



1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240

2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100

14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990

12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190

13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200

15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180

16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160

17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330

36 TiAl6V4 - 0.5 4.0 0.18 0.40 0.75 45 65 22.0 0.31 555

37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445

38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880

38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770

38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280

3

2

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

7 GG20, GG40, EN-GJL-250,

No30B

5X2CrNiN23-4,

S31500


St

eel


Low alloyed

High alloyed

Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

Cast

Iron

Grey

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

Malleable & Nodular 8GGG40, GGG70,

50005

CNMG 120408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






36


CNMG 120408 NX – LT 1025


1 125 HB 0.5 5.0 0.18 0.50 1.7 90 330 33.0 0.36 2240

2 190 HB 0.5 5.0 0.18 0.50 1.7 90 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.4 90 250 33.0 0.31 2200

6 180 HB 0.5 5.0 0.18 0.45 1.1 60 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.1 60 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.1 60 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 1.0 60 180 22.7 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.1 35 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.1 35 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.8 35 130 22.2 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.8 35 110 22.2 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100

14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990

12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190

13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

CNMG 120408 NX – LT 1005


1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265

2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240

3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220

6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145

10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155

10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130

11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110

11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220

15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200

16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155

38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990

38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775

38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665



St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

Cast

Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

37



1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130

15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555

37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



CNMG 120412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






38



1 125 HB 0.7 6.0 0.26 0.68 3.06 180 430 44.0 0.50 2265

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 365 44.0 0.46 2240

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 325 44.0 0.44 2220

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 365 44.0 0.42 2220

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 325 44.0 0.42 2200

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 275 44.0 0.40 1165

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 235 33.6 0.40 1145

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 245 33.4 0.40 1155

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 195 33.4 0.40 1130

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 170 22.9 0.37 1110

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 145 22.9 0.37 1100

15 150 HB 0.7 6.0 0.19 0.81 3.40 170 325 44.0 0.46 2220

15 200 HB 0.7 6.0 0.19 0.81 3.06 160 300 44.0 0.46 2200

16 250 HB 0.7 6.0 0.19 0.74 3.06 150 275 44.0 0.46 1175

17,19 150 HB 0.7 6.0 0.19 0.68 2.55 120 325 44.0 0.40 2200

17,19 200 HB 0.7 6.0 0.19 0.68 2.21 120 300 44.0 0.40 1175

18,20 250 HB 0.7 6.0 0.19 0.68 2.04 120 245 44.0 0.40 1155

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 130 22.7 0.33 990

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 115 22.0 0.26 775

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 105 11.3 0.24 665



St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

Cast

Iron

CNMG 120412 NN – LT 1025


1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190

13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130

17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


Cast

Iron

CNMG 120412 NN – LT 1005






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


39

TURNING

FProductivity

C N M M80° 0°

Shape Clearance Angle Toleranced ± 0.08m ± 0.13s ± 0.13

Ø d

l

m

Fixing,Chipbreaker

ss


T00041161.204.7612CNMM 120412 NR LT 1025

T00041150.804.7612CNMM 120408 NR LT 1025

F M R


80° diamond shape, single sided inserts. Strong cutting edge for roughing operations which includes inter-rupted cut, high feed and high depth of cut.

Application Guide

CNMM

,

40



1 125 HB 0.7 7.0 0.21 0.60 3.24 90 330 55.0 0.46 2240

2 190 HB 0.7 7.0 0.21 0.60 3.24 90 280 55.0 0.42 2220

3 250 HB 0.7 7.0 0.21 0.54 2.70 90 250 55.0 0.40 2200

6 180 HB 0.7 7.0 0.21 0.54 2.16 60 280 55.0 0.38 2200

4,6 230 HB 0.7 5.6 0.21 0.54 2.16 60 250 55.0 0.38 1180

5,7 280 HB 0.7 5.6 0.18 0.48 2.16 60 210 55.0 0.36 1150

8 350 HB 0.7 4.9 0.18 0.48 1.80 60 180 44.5 0.36 1130

10 220 HB 0.7 5.6 0.18 0.48 2.16 35 190 44.1 0.36 1140

10 280 HB 0.7 5.6 0.18 0.48 2.16 35 150 44.1 0.36 1120

11 320 HB 0.7 4.2 0.18 0.42 1.44 35 130 33.6 0.34 1100

11 350 HB 0.7 4.2 0.18 0.42 1.44 35 110 33.6 0.34 990

14 180 HB 0.7 7.0 0.20 0.48 2.16 85 270 55.0 0.30 1190

14 240 HB 0.7 7.0 0.20 0.48 1.80 80 220 55.0 0.26 1170

14 290 HB 0.7 5.6 0.18 0.42 1.44 40 150 44.1 0.29 1100

14 310 HB 0.7 5.6 0.18 0.42 1.44 35 140 44.1 0.29 990

12 200 HB 0.7 7.0 0.18 0.48 1.26 85 250 44.1 0.24 1190

13 42 HRc 0.7 5.6 0.18 0.48 1.26 60 190 33.6 0.24 1130

17,19 150 HB 0.7 7.0 0.15 0.60 2.70 60 250 55.0 0.36 1180

17,19 200 HB 0.7 7.0 0.15 0.60 2.34 60 230 55.0 0.36 1160

18,20 250 HB 0.7 7.0 0.15 0.60 2.16 60 190 55.0 0.36 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

CNMM 120412 NR – LT 1025

CNMM 120408 NR – LT 1025


1 125 HB 0.5 7.0 0.21 0.60 2.88 90 330 44.2 0.46 2240

2 190 HB 0.5 7.0 0.21 0.60 2.88 90 280 44.2 0.42 2220

3 250 HB 0.5 7.0 0.21 0.54 2.40 90 250 44.2 0.40 2200

6 180 HB 0.5 7.0 0.21 0.54 1.92 60 280 44.2 0.38 2200

4,6 230 HB 0.5 5.6 0.21 0.54 1.92 60 250 44.2 0.38 1180

5,7 280 HB 0.5 5.6 0.18 0.48 1.92 60 210 44.2 0.36 1150

8 350 HB 0.5 4.9 0.18 0.48 1.60 60 180 33.8 0.36 1130

10 220 HB 0.5 5.6 0.18 0.48 1.92 35 190 33.5 0.36 1140

10 280 HB 0.5 5.6 0.18 0.48 1.92 35 150 33.5 0.36 1120

11 320 HB 0.5 4.2 0.18 0.42 1.28 35 130 33.1 0.34 1100

11 350 HB 0.5 4.2 0.18 0.42 1.28 35 110 33.1 0.34 990

14 180 HB 0.5 7.0 0.20 0.48 1.92 85 270 44.2 0.30 1190

14 240 HB 0.5 7.0 0.20 0.48 1.60 80 220 44.2 0.26 1170

14 290 HB 0.5 5.6 0.18 0.42 1.28 40 150 33.5 0.29 1100

14 310 HB 0.5 5.6 0.18 0.42 1.28 35 140 33.5 0.29 990

12 200 HB 0.5 7.0 0.18 0.48 1.12 85 250 33.5 0.24 1190

13 42 HRc 0.5 5.6 0.18 0.48 1.12 60 190 33.1 0.24 1130

17,19 150 HB 0.5 7.0 0.15 0.60 2.40 60 250 44.2 0.36 1180

17,19 200 HB 0.5 7.0 0.15 0.60 2.08 60 230 44.2 0.36 1160

18,20 250 HB 0.5 7.0 0.15 0.60 1.92 60 190 44.2 0.36 1140

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


Cast

Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


41

TURNING

LT 1000

LT 1000

LT 1000 and 1025

NXCNMPTNMPWNMP

Stainless Steel

VC

Exotic Material


NX-CNMP-TNMP-WNMP


C N M P80° 0°


Ø d

l

m

Fixing,Chipbreaker

ss


T00019011.204.7612CNMP 120412 NN LT 1000

T00019000.804.7612CNMP 120408 NN LT 1000

F M R



T00041181.204.7612CNMP 120412 NN LT 1025

T00041170.804.7612CNMP 120408 NN LT 1025

F M R


80° diamond shape, double sided inserts with positive chipbreaker geometry. Generates low cutting force. Suitable for high temperature alloys.

Application Guide

Application guide

CNMP

42



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

Ste

el

Non-alloyed 1C35, Ck45, 1020,

1045, 1060, 28Mn6

Low alloyed 242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6


Sta

inle

ss S

teel

Austenitic 4304, 316, X5CrNi18-

9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Har

dene

d M

at.

Steel

11

GGG40, GGG70, 50005

Hig

h Te

mp.

Allo

ys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cas

t Ir

on

CNMP 120408 NN – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






43



1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.36 1130

15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.40 555

37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.37 445

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

CNMP 120412 NN – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






44



1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190

13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130

17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


Cast

Iron

CNMP 120408 NN – LT 1025

CNMP 120412 NN – LT 1025


1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


45

TURNING

FProductivity

Stainless Steel

VC

C P M T80° 11°


m

Tolerance

Ø d

s ± 0.13For l = 06/09, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13

Fixing, Chipbreaker

s



T00031460.803.979CPMT 09T308 NN LT 1000

T00030880.402.386CPMT 060204 NN LT 1000

T00031450.403.979CPMT 09T304 NN LT 1000

T00031440.802.386CPMT 060208 NN LT 1000

Application Guide

80° diamond shape inserts with positive chipbreaker geometry. Very popular and useful for boring (even of small diameters), facing and external turning operations.

CPMT

46



1 125 HB 0.4 2.1 0.08 0.20 0.37 180 330 11.0 0.16 2240

2 190 HB 0.4 1.8 0.08 0.19 0.32 180 280 11.0 0.16 2220

3 250 HB 0.4 1.8 0.08 0.17 0.30 180 250 11.0 0.16 2200

6 180 HB 0.4 1.8 0.08 0.17 0.31 120 280 11.0 0.14 2200

4,6 230 HB 0.4 1.8 0.08 0.17 0.30 120 250 11.0 0.14 1180

5,7 280 HB 0.4 1.4 0.08 0.15 0.25 120 210 11.0 0.14 1150

8 350 HB 0.4 1.4 0.08 0.15 0.22 120 180 11.0 0.14 1130

10 220 HB 0.4 1.8 0.07 0.15 0.25 70 190 11.0 0.11 1140

10 280 HB 0.4 1.8 0.07 0.14 0.25 70 150 11.0 0.11 1120

11 320 HB 0.4 1.4 0.07 0.12 0.20 70 130 11.0 0.11 1100

11 350 HB 0.4 1.4 0.07 0.12 0.16 70 110 11.0 0.11 990

14 180 HB 0.4 1.8 0.08 0.15 0.20 170 270 11.0 0.11 2220

14 240 HB 0.4 1.8 0.08 0.15 0.16 160 220 11.0 0.11 1190

14 290 HB 0.4 1.4 0.07 0.12 0.12 80 150 11.0 0.11 1100

14 310 HB 0.4 1.4 0.07 0.12 0.12 70 140 11.0 0.11 990

12 200 HB 0.4 1.8 0.08 0.15 0.20 170 250 00.9 0.14 2210

13 42 HRc 0.4 1.4 0.08 0.14 0.16 120 190 00.9 0.11 1140

15 150 HB 0.4 2.1 0.06 0.17 0.40 170 250 11.0 0.16 2200

15 200 HB 0.4 2.1 0.06 0.17 0.37 160 230 11.0 0.16 1180

16 250 HB 0.4 2.1 0.06 0.17 0.37 150 210 11.0 0.16 1160

17,19 150 HB 0.4 1.8 0.06 0.15 0.30 120 250 11.0 0.14 1180

17,19 200 HB 0.4 1.8 0.06 0.15 0.25 120 230 11.0 0.14 1160

18,20 250 HB 0.4 1.8 0.06 0.15 0.25 120 190 11.0 0.14 1140

31,32 Incoloy 800 240 HB 0.4 1.4 0.08 0.13 0.16 25 45 11.0 0.11 333

33 Inconel 700 250 HB 0.4 1.4 0.08 0.13 0.16 25 45 11.0 0.11 330

34 Stellite 21 350 HB 0.4 1.4 0.08 0.13 0.16 23 40 11.0 0.11 228

36 TiAl6V4 - 0.4 1.4 0.08 0.14 0.20 45 65 11.0 0.13 555

37 T40 - 0.4 1.4 0.08 0.12 0.16 35 55 11.0 0.11 445

38 45 HRc 0.4 1.3 0.04 0.10 0.12 50 100 00.8 0.10 880

38 50 HRc 0.4 1.1 0.04 0.09 0.11 40 90 00.6 0.08 770

38 55 HRc 0.4 1.0 0.04 0.08 0.08 40 80 00.5 0.06 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.4 2.8 0.08 0.26 0.43 200 400 1.0 0.18 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



CPMT 060204 NN – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






47



1 125 HB 0.2 3.0 0.11 0.23 0.60 180 330 11.6 0.18 2240

2 190 HB 0.2 2.5 0.11 0.22 0.52 180 280 11.6 0.18 2220

3 250 HB 0.2 2.5 0.11 0.20 0.48 180 250 11.6 0.18 2200

6 180 HB 0.2 2.5 0.11 0.20 0.50 120 280 11.6 0.15 2200

4,6 230 HB 0.2 2.5 0.11 0.20 0.48 120 250 11.6 0.15 1180

5,7 280 HB 0.2 2.0 0.11 0.18 0.40 120 210 11.6 0.15 1150

8 350 HB 0.2 2.0 0.11 0.18 0.35 120 180 11.6 0.15 1130

10 220 HB 0.2 2.5 0.10 0.18 0.40 70 190 11.6 0.12 1140

10 280 HB 0.2 2.5 0.10 0.16 0.40 70 150 11.6 0.12 1120

11 320 HB 0.2 2.0 0.10 0.14 0.32 70 130 11.6 0.12 1100

11 350 HB 0.2 2.0 0.10 0.14 0.26 70 110 11.6 0.12 990

14 180 HB 0.2 2.5 0.11 0.18 0.32 170 270 11.6 0.12 2220

14 240 HB 0.2 2.5 0.11 0.18 0.26 160 220 11.6 0.12 1190

14 290 HB 0.2 2.0 0.10 0.14 0.19 80 150 11.6 0.12 1100

14 310 HB 0.2 2.0 0.10 0.14 0.19 70 140 11.6 0.12 990

12 200 HB 0.2 2.5 0.11 0.18 0.32 170 250 11.4 0.15 2210

13 42 HRc 0.2 2.0 0.11 0.16 0.26 120 190 11.4 0.12 1140

15 150 HB 0.2 3.0 0.08 0.20 0.64 170 250 11.6 0.18 2200

15 200 HB 0.2 3.0 0.08 0.20 0.60 160 230 11.6 0.18 1180

16 250 HB 0.2 3.0 0.08 0.20 0.60 150 210 11.6 0.18 1160

17,19 150 HB 0.2 2.5 0.08 0.18 0.48 120 250 11.6 0.15 1180

17,19 200 HB 0.2 2.5 0.08 0.18 0.40 120 230 11.6 0.15 1160

18,20 250 HB 0.2 2.5 0.08 0.18 0.40 120 190 11.6 0.15 1140

31,32 Incoloy 800 240 HB 0.2 2.0 0.11 0.15 0.26 25 45 11.6 0.12 333

33 Inconel 700 250 HB 0.2 2.0 0.11 0.15 0.26 25 45 11.6 0.12 330

34 Stellite 21 350 HB 0.2 2.0 0.11 0.15 0.26 23 40 11.6 0.12 228

36 TiAl6V4 - 0.2 2.0 0.11 0.16 0.32 45 65 11.6 0.14 555

37 T40 - 0.2 2.0 0.11 0.14 0.26 35 55 11.6 0.12 445

38 45 HRc 0.2 1.8 0.06 0.12 0.19 50 100 11.3 0.11 880

38 50 HRc 0.2 1.6 0.06 0.11 0.18 40 90 11.0 0.09 770

38 55 HRc 0.2 1.4 0.06 0.09 0.13 40 80 00.8 0.07 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 3.9 0.11 0.30 0.69 200 400 1.6 0.20 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



CPMT 09T304 NN – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






48



1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.34 2240

2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220

3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.30 2200

6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200

4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180

5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150

8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 22.7 0.27 1130

10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140

10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120

11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.2 0.25 1100

11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.2 0.25 990

14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.23 1190

14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.20 1170

14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.22 1100

14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.22 990

12 200 HB 0.5 4.0 0.18 0.40 0.63 170 250 22.5 0.18 1190

13 42 HRc 0.5 3.2 0.18 0.40 0.63 120 190 22.2 0.18 1130

15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200

15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180

16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160

17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180

17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160

18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332

33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330

34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228

36 TiAl6V4 - 0.5 2.8 0.20 0.40 0.72 45 65 22.0 0.30 555

37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445

38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880

38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770

38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.62 200 400 3.0 0.36 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

CPMT 09T308 NN – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


49

TURNING

LT 10 and LT 1000

LT 10 and LT 1000

FProductivity

Stainless Steel

VC

D C M T7°

Shape Clearance Angle

55°

Toleranced ± 0.05m ± 0.08s ± 0.13

l

mØ d

Fixing, Chipbreaker

s

F M R

Application Guide



T00007210.803.9711DCMT 11T308 NN LT 10

T00000650.403.9711DCMT 11T304 NN LT 10

T00000640.402.387DCMT 070204 NN LT 10

F M

Application Guide


T00019040.803.9711DCMT 11T308 NN LT 1000

T00019030.403.9711DCMT 11T304 NN LT 1000

T00019020.402.387DCMT 070204 NN LT 1000


55° diamond shape inserts. Suitable for internal turning due to a unique chip removal geometry. Generates low cutting force. Most suitable for small work-pieces.

R

DCMT

50



1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300

2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260

3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240

6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260

4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240

5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200

8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180

10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180

10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140

11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120

11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110

14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260

14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210

14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140

14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140

12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240

13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180

15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240

15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220

16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200

17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240

17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220

18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180

31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335

36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660

37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550

38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990

38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880

38 55 HRc 0.0 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

DCMT 070204 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






51



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

DCMT 11T304 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






52



1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.32 2240

2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220

3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.32 2200

6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200

4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180

5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150

8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 33.0 0.27 1130

10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140

10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120

11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.5 0.25 1100

11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.5 0.25 990

14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.32 1190

14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.29 1170

14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.25 1100

14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.25 990

12 200 HB 0.5 4.0 0.22 0.40 0.90 170 250 33.0 0.29 1190

13 42 HRc 0.5 3.2 0.22 0.40 0.90 120 190 22.5 0.29 1130

15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200

15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180

16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160

17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180

17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160

18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332

33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330

34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228

36 TiAl6V4 - 0.5 3.2 0.20 0.40 0.72 45 65 22.0 0.30 555

37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445

38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880

38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770

38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.60 200 400 3.0 0.36 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

Suggested Starting Parameters

1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]

D.O.C. [mm]VDI Group

Material Examples* HardnessFeed [mm/rev] Vc [m/min]

Gr. N°

DCMT 11T308 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


53

TURNING

VC

Productivity



T00032421.206.3515DNMA 150612 LT 1005

T00032410.806.3515DNMA 150608 LT 1005

Application Guide

55° diamond shape flat inserts. Strong edge preparation, mainly for gray cast iron machining. Suitable for profiling of complex shapes, from roughing to finishing.

Fixing,Chipbreaker

D N M0°

Shape Clearance Angle Tolerance

55°

l

mØ d

s ± 0.13For l = 11, d ± 0.05 m ± 0.08 For l = 15, d ± 0.08 m ± 0.13

s

DNMA

54


DNMA 150608 – LT 1005

DNMA 150612 – LT 1005


15 150 HB 0.7 5.0 0.15 0.46 1.3 270 450 33.5 00.33 3350

15 200 HB 0.7 5.0 0.15 0.42 1.2 200 320 33.5 00.33 2250

16 250 HB 0.7 5.0 0.15 0.38 1.2 170 240 33.5 00.33 2220

17,19 150 HB 0.7 5.0 0.15 0.46 1.0 130 260 22.5 00.30 2240

17,19 200 HB 0.7 5.0 0.15 0.42 0.9 130 230 22.5 00.30 2210

18,20 250 HB 0.7 5.0 0.15 0.38 0.8 130 190 22.5 00.30 1180

CChilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.24 0.3 40 60 11.4 00.16 550

WWhite Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.24 0.2 30 50 11.0 00.15 440

HH 11

GGG40, GGG70, 50005

CCast

Iron

GGrey 7 GG20, GG40, EN-GJL-250,

No30B

MMalleable & Nodular 8

mmin mmax mmin mmax mmin mmax DD.O.C. FFeed VVcc

15 150 HB 0.7 5.0 0.15 0.42 1.3 270 450 33.2 00.30 3350

15 200 HB 0.7 5.0 0.15 0.40 1.2 200 320 33.2 00.30 2250

16 250 HB 0.7 5.0 0.15 0.36 1.2 170 240 33.2 00.30 2220

17,19 150 HB 0.7 5.0 0.15 0.42 1.0 130 260 22.5 00.28 2240

17,19 200 HB 0.7 5.0 0.15 0.40 0.8 130 230 22.5 00.28 2210

18,20 250 HB 0.7 5.0 0.15 0.36 0.8 130 190 22.5 00.28 1180

CChilled Cast Iron 40 Ni-Hard 2 400 HB 0.7 2.0 0.11 0.22 0.2 40 60 11.4 00.15 550

WWhite Cast Iron 41 G-X300CrMo15 55 HRc 0.7 1.5 0.11 0.22 0.2 30 50 11.0 00.15 440

HH 11

GGG40, GGG70, 50005

CCast

Iron

SSuggested Starting Parameters

FFeed [mm/rev] VVc [m/min]AAmax [mm²]

DD.O.C. [mm]MMaterial Group GGr. N°

VVDI Group

MMaterial Examples* HHardness

GGrey 7 GG20, GG40, EN-GJL-250,

No30B



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters







Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


55

TURNING



T00006721.206.3515DNMG 150612 NN LT 10

T00000670.806.3515DNMG 150608 NN LT 10

T00005830.406.3515DNMG 150604 NN LT 10

T00010211.204.7615DNMG 150412 NN LT 10

T00004750.804.7615DNMG 150408 NN LT 10

T00004760.404.7615DNMG 150404 NN LT 10

T00006750.804.7611DNMG 110408 NN LT 10

T00000660.404.7611DNMG 110404 NN LT 10

D N M G0°

Shape Clearance Angle Tolerance Fixing, Chipbreaker

55°

l

mØ d

s

s ± 0.13For l = 11, d ± 0.05 m ± 0.08 For l = 15, d ± 0.08 m ± 0.13



T00030970.804.7615DNMG 150408 NX LT 1000

T00032200.806.3515DNMG 150608 NX LT 1000

T00019110.806.3515DNMG 150608 NN LT 1000

T00019100.406.3515DNMG 150604 NN LT 1000

T00019091.204.7615DNMG 150412 NN LT 1000

T00019080.804.7615DNMG 150408 NN LT 1000

T00019070.404.7615DNMG 150404 NN LT 1000

T00019060.804.7611DNMG 110408 NN LT 1000

T00019050.404.7611DNMG 110404 NN LT 1000

T00019121.206.3515DNMG 150612 NN LT 1000

LT 10 and LT 1000


LT 10 and LT 1000

NX-CNMP-TNMP-WNMP



FProductivity

Stainless Steel

VC

Application Guide

Application Guide

DNMG

55°

56

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14




T00041271.206.3515DNMG 150612 NN LT 1025

T0004123

T0004126

0.80

0.80

6.35

6.35

15

15

DNMG 150608 NX LT 1025

DNMG 150608 NN LT 1025

T0004124

T0004122

1.20

1.20

4.76

4.76

15

15

DNMG 150412 NN LT 1025

DNMG 150408 NX LT 1025

T00041210.804.7615DNMG 150408 NN LT 1025

T00041190.804.7611DNMG 110408 NN LT 1025

Application Guide


NX-CNMP-TNMP-WNMP


Productivity

D N M G

55° diamond shape inserts. Suitable for profiling of complex shapes, from roughing to finishing.



T00040681.206.3515DNMG 150612 NN LT 1005

T0004063

T0004067

0.80

0.80

6.35

6.35

15

15

DNMG 150608 NX LT 1005

DNMG 150608 NN LT 1005

T0004064

T0004062

1.20

1.20

4.76

4.76

15

15

DNMG 150412 NN LT 1005

DNMG 150408 NX LT 1005

T00040610.804.7615DNMG 150408 NN LT 1005

T00040590.804.7611DNMG 110408 NN LT 1005

Application Guide

NX chipbreaker NN chipbreaker

57



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



DNMG 110404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






58



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



St

eel

Non-alloyed

Low alloyed

Material Group Gr. N°

DNMG 110408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






59


DNMG 110408 NN – LT 1025


1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

DNMG 110408 NN – LT 1005


1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665




St

eel


Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

Cast

Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

60



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.0 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

DNMG 150404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






61



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

DNMG 150408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






62



1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

DNMG 150408 NN – LT 1005


1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

DNMG 150408 NN – LT 1025






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

63



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

DNMG 150408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






64


DNMG 150408 NX – LT 1025


1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240

2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200

6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100

14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990

12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190

13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

DNMG 150408 NX – LT 1005


1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265

2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240

3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220

6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145

10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155

10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130

11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110

11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220

15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200

16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155

38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990

38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775

38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

65



1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130

15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555

37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

DNMG 150412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






66


DNMG 150412 NN – LT 1025


1 125 HB 0.7 6.0 0.26 0.68 3.06 90 330 44.0 0.50 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 90 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 90 250 44.0 0.44 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 60 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 60 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 60 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 60 180 33.6 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 35 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 35 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 35 130 22.9 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 35 110 22.9 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 85 270 44.0 0.33 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 80 220 44.0 0.29 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 40 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 35 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.23 0.54 1.19 85 250 33.4 0.26 1190

13 42 HRc 0.7 4.8 0.23 0.54 1.19 60 190 22.9 0.26 1130

17,19 150 HB 0.7 6.0 0.19 0.68 2.55 60 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.19 0.68 2.21 60 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.19 0.68 2.04 60 190 44.0 0.40 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

DNMG 150412 NN – LT 1005


1 125 HB 0.7 6.0 0.26 0.68 3.06 180 430 44.0 0.50 2265

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 365 44.0 0.46 2240

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 325 44.0 0.44 2220

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 365 44.0 0.42 2220

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 325 44.0 0.42 2200

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 275 44.0 0.40 1165

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 235 33.6 0.40 1145

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 245 33.4 0.40 1155

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 195 33.4 0.40 1130

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 170 22.9 0.37 1110

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 145 22.9 0.37 1100

15 150 HB 0.7 6.0 0.19 0.81 3.40 170 325 44.0 0.46 2220

15 200 HB 0.7 6.0 0.19 0.81 3.06 160 300 44.0 0.46 2200

16 250 HB 0.7 6.0 0.19 0.74 3.06 150 275 44.0 0.46 1175

17,19 150 HB 0.7 6.0 0.19 0.68 2.55 120 325 44.0 0.40 2200

17,19 200 HB 0.7 6.0 0.19 0.68 2.21 120 300 44.0 0.40 1175

18,20 250 HB 0.7 6.0 0.19 0.68 2.04 120 245 44.0 0.40 1155

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 130 22.7 0.33 990

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 115 22.0 0.26 775

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 105 11.3 0.24 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

67



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

DNMG 150604 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






68



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

St

eel

Non-alloyed

Low alloyed

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

DNMG 150608 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






69


DNMG 150608 NN – LT 1025

DNMG 150608 NN – LT 1005


1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular


1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665




Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

70



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 3.5 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

St

eel

Non-alloyed

Low alloyed



1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

DNMG 150608 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






71


DNMG 150608 NX – LT 1025


1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240

2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200

6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100

14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990

12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190

13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140

Amax [mm²]

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



DNMG 150608 NX – LT 1005


1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265

2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240

3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220

6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 120 275 33.0 0.29 1165

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 235 22.7 0.29 1145

10 220 HB 0.5 4.0 0.16 0.40 1.14 70 245 22.5 0.29 1155

10 280 HB 0.5 4.0 0.16 0.40 1.14 70 195 22.5 0.29 1130

11 320 HB 0.5 3.0 0.16 0.35 0.76 70 170 22.2 0.27 1110

11 350 HB 0.5 3.0 0.16 0.35 0.76 70 145 22.2 0.27 1100

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220

15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200

16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155

38 45 HRc 0.5 2.5 0.10 0.30 0.57 50 130 22.0 0.24 990

38 50 HRc 0.5 2.0 0.10 0.25 0.38 40 115 11.5 0.19 775

38 55 HRc 0.5 1.5 0.10 0.20 0.29 40 105 11.0 0.17 665



St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

Cast

Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

72



1 125 HB 0.7 6.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 6.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 6.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 6.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 4.8 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 4.8 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 4.2 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 4.8 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 4.8 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 3.6 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 3.6 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 6.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 6.0 0.25 0.54 1.70 160 220 44.0 0.38 1170

14 290 HB 0.7 4.8 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 4.8 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 6.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 4.8 0.28 0.54 1.70 120 190 33.0 0.35 1130

15 150 HB 0.7 6.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 6.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 6.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 6.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 6.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 6.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 3.6 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 3.6 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 4.8 0.25 0.54 1.36 45 65 22.7 0.44 555

37 T40 - 0.7 3.6 0.25 0.47 1.19 35 55 22.7 0.40 445

38 45 HRc 0.7 3.0 0.14 0.41 1.02 50 100 22.7 0.33 880

38 50 HRc 0.7 2.4 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 1.8 0.14 0.27 0.51 40 80 11.3 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 4.0 0.50 280

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

DNMG 150612 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


73

TURNING

VC

Productivity

Stainless Steel

VC

D N U X0°

Shape Clearance Angle Fixing,Chipbreaker

55°

l

mØ d

s

Toleranced ± 0.08m ± 0.13s ± 0.13

F M R

Application Guide



T00021570.806.3515DNUX 150608 R11 LT10

F M R

Application Guide


T00027930.806.3515DNUX 150608 R11 LT 1000


55° nose angle inserts with four cutting edges. Excellent chip control and low cutting force. Suitable for conventional turning operations and long shafts.

DNUX

74


DNUX 150608 R11 – LT 10 | LT 1000


1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240

2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100

14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990

12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190

13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200

15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180

16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160

17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330

36 TiAl6V4 - 0.5 3.5 0.18 0.40 0.75 45 65 22.0 0.31 555

37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445

38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880

38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770

38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280


No30B

Malleable & Nodular

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

10

8

Ferritic & Martensitic 6

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron

Stai

nles

s St

eel


X5CrNi18-9


S31500

410, X6Cr17, 17-4 PH, 430

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


2


1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



St

eel

Non-alloyed

Low alloyed


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


75

TURNING

KNUX 160405 L LT 10

VC

Productivity

Stainless Steel

VC

K N U X0°


Ø d

l

m

Toleranced ± 0.08m ± 0.13s ± 0.13

Fixing, Chipbreaker

55°

s

F M R

Application Guide



T0000951

T0003884

0.50

0.50

4.76

4.76

16

16

KNUX 160405 R LT 10

55

A 55° nose angle inserts with two cutting edges. Popular insert with excellent chip control and low cutting force. Suitable for conventional turning operations.

KNUX

76



1 125 HB 0.2 5.0 0.11 0.23 0.85 180 330 33.0 0.18 3300

2 190 HB 0.2 4.2 0.11 0.22 0.73 180 280 33.0 0.18 2260

3 250 HB 0.2 4.2 0.11 0.20 0.68 180 250 33.0 0.18 2240

6 180 HB 0.2 4.2 0.10 0.20 0.71 120 280 33.0 0.15 2260

4,6 230 HB 0.2 4.2 0.10 0.20 0.68 120 250 33.0 0.15 2240

5,7 280 HB 0.2 3.3 0.10 0.18 0.56 120 210 33.0 0.15 2200

8 350 HB 0.2 3.3 0.10 0.18 0.51 120 180 33.0 0.15 1180

10 220 HB 0.2 4.2 0.09 0.18 0.56 70 190 22.0 0.12 1180

10 280 HB 0.2 4.2 0.09 0.16 0.56 70 150 22.0 0.12 1140

11 320 HB 0.2 3.3 0.09 0.14 0.45 70 130 22.0 0.12 1120

11 350 HB 0.2 3.3 0.09 0.14 0.37 70 110 22.0 0.12 1110

14 180 HB 0.2 4.2 0.10 0.18 0.60 170 270 33.0 0.15 2260

14 240 HB 0.2 4.2 0.10 0.18 0.50 160 220 33.0 0.15 2210

14 290 HB 0.2 3.3 0.09 0.14 0.40 80 150 22.0 0.15 1140

14 310 HB 0.2 3.3 0.09 0.14 0.40 70 140 22.0 0.15 1140

12 200 HB 0.2 4.2 0.10 0.18 0.50 170 250 33.0 0.15 2240

13 42 HRc 0.2 3.3 0.10 0.16 0.45 120 190 22.0 0.15 1180

15 150 HB 0.2 5.0 0.08 0.20 0.85 170 250 33.0 0.18 2240

15 200 HB 0.2 5.0 0.08 0.20 0.75 160 230 33.0 0.18 2220

16 250 HB 0.2 5.0 0.08 0.20 0.65 150 210 33.0 0.18 2200

17,19 150 HB 0.2 4.2 0.08 0.18 0.68 120 250 22.5 0.15 2240

17,19 200 HB 0.2 4.2 0.08 0.18 0.60 120 230 22.5 0.15 2220

18,20 250 HB 0.2 4.2 0.08 0.18 0.56 120 190 22.5 0.15 1180

31,32 Incoloy 800 240 HB 0.2 3.3 0.09 0.15 0.40 25 50 22.0 0.12 440

33 Inconel 700 250 HB 0.2 3.3 0.09 0.15 0.40 25 50 22.0 0.12 440

34 Stellite 21 350 HB 0.2 3.3 0.09 0.15 0.40 23 45 22.0 0.12 335

36 TiAl6V4 - 0.2 3.3 0.09 0.16 0.45 45 65 22.0 0.15 660

37 T40 - 0.2 3.3 0.09 0.14 0.40 35 60 22.0 0.12 550

38 45 HRc 0.2 3.0 0.05 0.12 0.28 50 100 11.8 0.11 990

38 50 HRc 0.2 2.5 0.05 0.10 0.24 40 90 11.4 0.09 880

38 55 HRc 0.2 2.3 0.05 0.09 0.18 40 80 11.2 0.07 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 6.6 0.10 0.30 0.99 200 400 3.0 0.20 350

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5



Low alloyed

D.O.C. [mm]

2



KNUX 160405 L/R – LT 10

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


77

TURNING

FProductivity

Stainless Steel

VC

R C M T7° Ø d

Shape Clearance Angle Tolerances ± 0.13For l = 06/08/10, d ± 0.05 m ± 0.08 For l = 12, d ± 0.08 m ± 0.13

Fixing,Chipbreaker

s

l

F M R

Application Guide



T00000936.004.7612RCMT 1204 M0 LT 10

T00000925.003.9710RCMT 10T3 M0 LT 10

T00000914.003.188RCMT 0803 M0 LT 10

T00000903.002.386RCMT 0602 M0 LT 10

F M R

Application Guide


T00019176.004.7612RCMT 1204 M0 LT 1000

T00019165.003.9710RCMT 10T3 M0 LT 1000

T00019154.003.188RCMT 0803 M0 LT 1000

T00019143.002.386RCMT 0602 M0 LT 1000


Round inserts with positive rake angle and excellent edge resistance. Suitable for profiling operations of mill rolls and aerospace parts

RCMT

78



1 125 HB 0.5 2.0 0.15 0.40 0.64 180 330 11.0 0.35 2240

2 190 HB 0.5 2.0 0.15 0.40 0.64 180 280 11.0 0.35 2220

3 250 HB 0.5 1.5 0.15 0.35 0.56 180 250 11.0 0.30 2200

6 180 HB 0.5 2.0 0.15 0.35 0.56 120 280 11.0 0.30 2200

4,6 230 HB 0.5 2.0 0.15 0.35 0.48 120 250 11.0 0.30 1180

5,7 280 HB 0.5 2.0 0.15 0.35 0.40 120 210 11.0 0.30 1150

8 350 HB 0.5 1.5 0.15 0.35 0.36 120 180 11.0 0.30 1130

10 220 HB 0.5 2.0 0.13 0.35 0.48 70 190 11.0 0.30 1140

10 280 HB 0.5 2.0 0.13 0.30 0.40 70 150 11.0 0.28 1120

11 320 HB 0.5 1.5 0.13 0.30 0.32 70 130 11.0 0.28 1100

11 350 HB 0.5 1.5 0.13 0.30 0.26 70 110 11.0 0.28 990

14 180 HB 0.5 2.0 0.14 0.35 0.32 170 270 11.0 0.32 2220

14 240 HB 0.5 2.0 0.14 0.32 0.32 160 220 11.0 0.32 1190

14 290 HB 0.5 1.5 0.13 0.30 0.30 80 150 11.0 0.28 1100

14 310 HB 0.5 1.5 0.13 0.30 0.30 70 140 11.0 0.28 990

12 200 HB 0.5 2.0 0.15 0.35 0.32 170 250 11.0 0.32 2210

13 42 HRc 0.5 2.0 0.15 0.30 0.30 120 190 11.0 0.28 1140

15 150 HB 0.5 2.0 0.11 0.45 0.70 170 250 11.0 0.35 2200

15 200 HB 0.5 2.0 0.11 0.45 0.65 160 230 11.0 0.35 1180

16 250 HB 0.5 2.0 0.11 0.45 0.60 150 210 11.0 0.35 1160

17,19 150 HB 0.5 2.0 0.11 0.35 0.60 120 250 11.0 0.30 1180

17,19 200 HB 0.5 2.0 0.11 0.35 0.50 120 230 11.0 0.30 1160

18,20 250 HB 0.5 2.0 0.11 0.35 0.45 120 190 11.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 1.5 0.13 0.30 0.30 25 50 11.0 0.28 333

33 Inconel 700 250 HB 0.5 1.5 0.13 0.30 0.30 25 50 11.0 0.28 330

34 Stellite 21 350 HB 0.5 1.5 0.13 0.30 0.30 23 45 11.0 0.28 228

36 TiAl6V4 - 0.5 1.5 0.13 0.32 0.32 45 65 11.0 0.30 555

37 T40 - 0.5 1.5 0.13 0.30 0.30 35 60 11.0 0.28 445

38 45 HRc 0.5 1.2 0.05 0.22 0.20 50 100 00.9 0.18 880

38 50 HRc 0.5 1.0 0.05 0.18 0.17 40 90 00.7 0.16 770

38 55 HRc 0.3 0.8 0.05 0.14 0.12 40 80 00.6 0.12 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.0 0.15 0.40 0.70 200 400 1.0 0.35 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5



Low alloyed

D.O.C. [mm]

2



RCMT 0602 M0 – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






79



1 125 HB 0.5 2.4 0.15 0.40 0.77 180 330 11.2 0.35 2240

2 190 HB 0.5 2.4 0.15 0.40 0.77 180 280 11.2 0.35 2220

3 250 HB 0.5 1.8 0.15 0.35 0.67 180 250 11.2 0.30 2200

6 180 HB 0.5 2.4 0.15 0.35 0.67 120 280 11.2 0.30 2200

4,6 230 HB 0.5 2.4 0.15 0.35 0.58 120 250 11.2 0.30 1180

5,7 280 HB 0.5 2.4 0.15 0.35 0.48 120 210 11.2 0.30 1150

8 350 HB 0.5 1.8 0.15 0.35 0.43 120 180 11.2 0.30 1130

10 220 HB 0.5 2.4 0.13 0.35 0.58 70 190 11.2 0.30 1140

10 280 HB 0.5 2.4 0.13 0.30 0.48 70 150 11.2 0.28 1120

11 320 HB 0.5 1.8 0.13 0.30 0.38 70 130 11.2 0.28 1100

11 350 HB 0.5 1.8 0.13 0.30 0.31 70 110 11.2 0.28 990

14 180 HB 0.5 2.4 0.14 0.35 0.38 170 270 11.2 0.32 2220

14 240 HB 0.5 2.4 0.14 0.32 0.38 160 220 11.2 0.32 1190

14 290 HB 0.5 1.8 0.13 0.30 0.36 80 150 11.2 0.28 1100

14 310 HB 0.5 1.8 0.13 0.30 0.36 70 140 11.2 0.28 990

12 200 HB 0.5 2.4 0.15 0.35 0.38 170 250 11.2 0.32 2210

13 42 HRc 0.5 2.4 0.15 0.30 0.36 120 190 11.2 0.28 1140

15 150 HB 0.5 2.4 0.11 0.45 0.84 170 250 11.2 0.35 2200

15 200 HB 0.5 2.4 0.11 0.45 0.78 160 230 11.2 0.35 1180

16 250 HB 0.5 2.4 0.11 0.45 0.72 150 210 11.2 0.35 1160

17,19 150 HB 0.5 2.4 0.11 0.35 0.72 120 250 11.2 0.30 1180

17,19 200 HB 0.5 2.4 0.11 0.35 0.60 120 230 11.2 0.30 1160

18,20 250 HB 0.5 2.4 0.11 0.35 0.54 120 190 11.2 0.30 1140

31,32 Incoloy 800 240 HB 0.5 1.8 0.13 0.30 0.36 25 50 11.2 0.28 333

33 Inconel 700 250 HB 0.5 1.8 0.13 0.30 0.36 25 50 11.2 0.28 330

34 Stellite 21 350 HB 0.5 1.8 0.13 0.30 0.36 23 45 11.2 0.28 228

36 TiAl6V4 - 0.5 1.8 0.13 0.32 0.38 45 65 11.2 0.30 555

37 T40 - 0.5 1.8 0.13 0.30 0.36 35 60 11.2 0.28 445

38 45 HRc 0.5 1.4 0.05 0.22 0.24 50 100 11.1 0.18 880

38 50 HRc 0.5 1.2 0.05 0.18 0.20 40 90 00.8 0.16 770

38 55 HRc 0.3 1.0 0.05 0.14 0.14 40 80 00.7 0.12 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.4 0.15 0.40 0.84 200 400 1.2 0.35 280



Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


RCMT 0803 M0 – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






80



1 125 HB 0.5 2.8 0.15 0.40 0.90 180 330 11.4 0.35 2240

2 190 HB 0.5 2.8 0.15 0.40 0.90 180 280 11.4 0.35 2220

3 250 HB 0.5 2.1 0.15 0.35 0.78 180 250 11.4 0.30 2200

6 180 HB 0.5 2.8 0.15 0.35 0.78 120 280 11.4 0.30 2200

4,6 230 HB 0.5 2.8 0.15 0.35 0.67 120 250 11.4 0.30 1180

5,7 280 HB 0.5 2.8 0.15 0.35 0.56 120 210 11.4 0.30 1150

8 350 HB 0.5 2.1 0.15 0.35 0.50 120 180 11.4 0.30 1130

10 220 HB 0.5 2.8 0.13 0.35 0.67 70 190 11.4 0.30 1140

10 280 HB 0.5 2.8 0.13 0.30 0.56 70 150 11.4 0.28 1120

11 320 HB 0.5 2.1 0.13 0.30 0.45 70 130 11.4 0.28 1100

11 350 HB 0.5 2.1 0.13 0.30 0.36 70 110 11.4 0.28 990

14 180 HB 0.5 2.8 0.14 0.35 0.45 170 270 11.4 0.32 2220

14 240 HB 0.5 2.8 0.14 0.32 0.45 160 220 11.4 0.32 1190

14 290 HB 0.5 2.1 0.13 0.30 0.42 80 150 11.4 0.28 1100

14 310 HB 0.5 2.1 0.13 0.30 0.42 70 140 11.4 0.28 990

12 200 HB 0.5 2.8 0.15 0.35 0.45 170 250 11.4 0.32 2210

13 42 HRc 0.5 2.8 0.15 0.30 0.42 120 190 11.4 0.28 1140

15 150 HB 0.5 2.8 0.11 0.45 0.98 170 250 11.4 0.35 2200

15 200 HB 0.5 2.8 0.11 0.45 0.91 160 230 11.4 0.35 1180

16 250 HB 0.5 2.8 0.11 0.45 0.84 150 210 11.4 0.35 1160

17,19 150 HB 0.5 2.8 0.11 0.35 0.84 120 250 11.4 0.30 1180

17,19 200 HB 0.5 2.8 0.11 0.35 0.70 120 230 11.4 0.30 1160

18,20 250 HB 0.5 2.8 0.11 0.35 0.63 120 190 11.4 0.30 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.13 0.30 0.42 25 50 11.4 0.28 333

33 Inconel 700 250 HB 0.5 2.1 0.13 0.30 0.42 25 50 11.4 0.28 330

34 Stellite 21 350 HB 0.5 2.1 0.13 0.30 0.42 23 45 11.4 0.28 228

36 TiAl6V4 - 0.5 2.1 0.13 0.32 0.45 45 65 11.4 0.30 555

37 T40 - 0.5 2.1 0.13 0.30 0.42 35 60 11.4 0.28 445

38 45 HRc 0.5 1.7 0.05 0.22 0.28 50 100 11.3 0.18 880

38 50 HRc 0.5 1.4 0.05 0.18 0.24 40 90 11.0 0.16 770

38 55 HRc 0.3 1.1 0.05 0.14 0.17 40 80 00.8 0.12 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.8 0.15 0.40 0.98 200 400 1.4 0.35 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5



Low alloyed

D.O.C. [mm]

2



RCMT 10T3 M0 – LT 10 | LT 1000


GroupMaterial

ExemplesHardness



Parameters


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






81



1 125 HB 0.5 3.2 0.15 0.40 1.54 180 330 22.0 0.37 2240

2 190 HB 0.5 3.2 0.15 0.40 1.54 180 280 22.0 0.37 2220

3 250 HB 0.5 2.4 0.15 0.35 1.34 180 250 22.0 0.32 2200

6 180 HB 0.5 3.2 0.15 0.35 1.34 120 280 22.0 0.32 2200

4,6 230 HB 0.5 3.2 0.15 0.35 1.15 120 250 22.0 0.32 1180

5,7 280 HB 0.5 3.2 0.15 0.35 0.96 120 210 22.0 0.32 1150

8 350 HB 0.5 2.4 0.15 0.35 0.86 120 180 22.0 0.32 1130

10 220 HB 0.5 3.2 0.13 0.35 1.15 70 190 22.0 0.32 1140

10 280 HB 0.5 3.2 0.13 0.30 0.96 70 150 22.0 0.29 1120

11 320 HB 0.5 2.4 0.13 0.30 0.77 70 130 22.0 0.29 1100

11 350 HB 0.5 2.4 0.13 0.30 0.62 70 110 22.0 0.25 990

14 180 HB 0.5 3.2 0.14 0.35 0.77 170 270 22.0 0.32 2220

14 240 HB 0.5 3.2 0.14 0.32 0.77 160 220 22.0 0.30 1190

14 290 HB 0.5 2.4 0.13 0.30 0.72 80 150 22.0 0.29 1100

14 310 HB 0.5 2.4 0.13 0.30 0.72 70 140 22.0 0.29 990

12 200 HB 0.5 3.2 0.15 0.35 0.77 170 250 22.0 0.26 2210

13 42 HRc 0.5 3.2 0.15 0.30 0.72 120 190 22.0 0.23 1140

15 150 HB 0.5 3.2 0.11 0.45 1.68 170 250 22.0 0.37 2200

15 200 HB 0.5 3.2 0.11 0.45 1.56 160 230 22.0 0.37 1180

16 250 HB 0.5 3.2 0.11 0.45 1.44 150 210 22.0 0.37 1160

17,19 150 HB 0.5 3.2 0.11 0.35 1.44 120 250 22.0 0.32 1180

17,19 200 HB 0.5 3.2 0.11 0.35 1.20 120 230 22.0 0.32 1160

18,20 250 HB 0.5 3.2 0.11 0.35 1.08 120 190 22.0 0.32 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.13 0.30 0.72 25 50 22.0 0.29 335

33 Inconel 700 250 HB 0.5 2.4 0.13 0.30 0.72 25 50 22.0 0.29 330

34 Stellite 21 350 HB 0.5 2.4 0.13 0.30 0.72 25 45 22.0 0.29 330

36 TiAl6V4 - 0.5 2.4 0.13 0.32 0.77 45 65 22.0 0.32 555

37 T40 - 0.5 2.4 0.13 0.30 0.72 35 60 22.0 0.29 445

38 45 HRc 0.5 1.9 0.05 0.22 0.48 50 100 11.8 0.19 880

38 50 HRc 0.5 1.6 0.05 0.18 0.41 40 90 11.4 0.17 770

38 55 HRc 0.3 1.3 0.05 0.14 0.29 40 80 11.2 0.13 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.2 0.15 0.40 1.68 200 400 2.0 0.37 280



Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


RCMT 1204 M0 – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






82

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


S C M T7°

l

Shape Clearance Angle Tolerance d ± 0.05m ± 0.08s ± 0.13

90° Ø dm

Fixing,Chipbreaker

s

F M R

Application Guide



T00014580.803.979SCMT 09T308 NN LT 10

T00014590.403.979SCMT 09T304 NN LT 10

F M R

Application Guide


T00019190.803.979SCMT 09T308 NN LT 1000

T00019180.403.979SCMT 09T304 NN LT 1000


TURNING

90°

FProductivity

Stainless Steel

VC

Square inserts with a positive rake angle and excellent cutting edge resistance. Suitable for boring operations.

83



1 125 HB 0.3 4.0 0.11 0.26 0.72 180 330 22.5 0.18 3300

2 190 HB 0.3 3.3 0.11 0.25 0.62 180 280 22.5 0.18 2260

3 250 HB 0.3 3.3 0.11 0.23 0.58 180 250 22.5 0.18 2240

6 180 HB 0.3 3.3 0.10 0.23 0.60 120 280 22.5 0.14 2260

4,6 230 HB 0.3 3.3 0.10 0.23 0.58 120 250 22.5 0.14 2240

5,7 280 HB 0.3 2.7 0.10 0.21 0.48 120 210 22.5 0.13 2200

8 350 HB 0.3 2.7 0.10 0.21 0.43 120 180 22.5 0.13 1180

10 220 HB 0.3 3.3 0.09 0.21 0.48 70 190 22.1 0.10 1180

10 280 HB 0.3 3.3 0.09 0.18 0.48 70 150 22.1 0.10 1140

11 320 HB 0.3 2.7 0.09 0.16 0.38 70 130 22.1 0.10 1120

11 350 HB 0.3 2.7 0.09 0.16 0.31 70 110 22.1 0.10 1110

14 180 HB 0.3 3.3 0.08 0.21 0.38 170 270 22.5 0.09 2260

14 240 HB 0.3 3.3 0.08 0.21 0.31 160 220 22.5 0.08 2210

14 290 HB 0.3 2.7 0.08 0.16 0.24 80 150 22.1 0.08 1140

14 310 HB 0.3 2.7 0.08 0.16 0.24 70 140 22.1 0.08 1140

12 200 HB 0.3 3.3 0.08 0.21 0.38 170 250 22.1 0.09 2240

13 42 HRc 0.3 2.7 0.08 0.18 0.31 120 190 11.9 0.08 1180

15 150 HB 0.3 4.0 0.08 0.23 0.77 170 250 22.5 0.18 2240

15 200 HB 0.3 4.0 0.08 0.23 0.72 160 230 22.5 0.18 2220

16 250 HB 0.3 4.0 0.08 0.23 0.72 150 210 22.5 0.18 2200

17,19 150 HB 0.3 3.3 0.08 0.21 0.58 120 250 22.5 0.13 2240

17,19 200 HB 0.3 3.3 0.08 0.21 0.48 120 230 22.5 0.13 2220

18,20 250 HB 0.3 3.3 0.08 0.21 0.48 120 190 22.5 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.7 0.09 0.17 0.31 25 50 11.6 0.10 440

33 Inconel 700 250 HB 0.3 2.7 0.09 0.17 0.31 25 50 11.6 0.10 440

34 Stellite 21 350 HB 0.3 2.7 0.09 0.17 0.31 23 45 11.6 0.10 335

36 TiAl6V4 - 0.3 2.7 0.09 0.18 0.38 45 65 11.6 0.14 660

37 T40 - 0.3 2.7 0.09 0.16 0.31 35 60 11.6 0.10 550

38 45 HRc 0.3 2.4 0.05 0.14 0.24 50 100 11.8 0.10 990

38 50 HRc 0.3 2.0 0.05 0.12 0.20 40 90 11.4 0.08 880

38 55 HRc 0.3 1.9 0.05 0.10 0.16 40 80 11.1 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 5.3 0.10 0.35 0.84 200 400 2.5 0.23 350

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5



Low alloyed

D.O.C. [mm]

2



SCMT 09T304 – LT 10 | LT 1000

SCMT

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






84



1 125 HB 0.5 4.0 0.21 0.50 1.62 180 330 33.0 0.32 2240

2 190 HB 0.5 4.0 0.21 0.50 1.62 180 280 33.0 0.32 2220

3 250 HB 0.5 4.0 0.21 0.45 1.35 180 250 33.0 0.32 2200

6 180 HB 0.5 4.0 0.21 0.45 1.08 120 280 33.0 0.29 2200

4,6 230 HB 0.5 3.2 0.21 0.45 1.08 120 250 33.0 0.29 1180

5,7 280 HB 0.5 3.2 0.18 0.40 1.08 120 210 33.0 0.27 1150

8 350 HB 0.5 2.8 0.18 0.40 0.90 120 180 33.0 0.27 1130

10 220 HB 0.5 3.2 0.18 0.40 1.08 70 190 22.5 0.27 1140

10 280 HB 0.5 3.2 0.18 0.40 1.08 70 150 22.5 0.27 1120

11 320 HB 0.5 2.4 0.18 0.35 0.72 70 130 22.5 0.25 1100

11 350 HB 0.5 2.4 0.18 0.35 0.72 70 110 22.5 0.25 990

14 180 HB 0.5 4.0 0.20 0.40 1.08 170 270 33.0 0.32 2200

14 240 HB 0.5 4.0 0.20 0.40 0.90 160 220 33.0 0.29 1180

14 290 HB 0.5 3.2 0.18 0.35 0.72 80 150 22.5 0.25 1100

14 310 HB 0.5 3.2 0.18 0.35 0.72 70 140 22.5 0.25 990

12 200 HB 0.5 4.0 0.22 0.40 0.90 170 250 33.0 0.29 1190

13 42 HRc 0.5 3.2 0.22 0.40 0.90 120 190 22.5 0.29 1130

15 150 HB 0.5 4.0 0.15 0.60 1.80 170 250 33.0 0.32 2200

15 200 HB 0.5 4.0 0.15 0.60 1.62 160 230 33.0 0.32 1180

16 250 HB 0.5 4.0 0.15 0.55 1.62 150 210 33.0 0.32 1160

17,19 150 HB 0.5 4.0 0.15 0.50 1.35 120 250 33.0 0.27 1180

17,19 200 HB 0.5 4.0 0.15 0.50 1.17 120 230 33.0 0.27 1160

18,20 250 HB 0.5 4.0 0.15 0.50 1.08 120 190 33.0 0.27 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 332

33 Inconel 700 250 HB 0.5 2.4 0.20 0.35 0.63 25 45 22.0 0.25 330

34 Stellite 21 350 HB 0.5 2.4 0.20 0.35 0.63 23 40 22.0 0.25 228

36 TiAl6V4 - 0.5 3.2 0.20 0.40 0.72 45 65 22.0 0.30 555

37 T40 - 0.5 2.4 0.20 0.35 0.63 35 55 22.0 0.27 445

38 45 HRc 0.5 2.0 0.11 0.30 0.54 50 100 22.0 0.23 880

38 50 HRc 0.5 1.6 0.11 0.25 0.36 40 90 11.5 0.18 770

38 55 HRc 0.5 1.2 0.11 0.20 0.27 40 80 11.0 0.16 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.20 0.60 1.60 200 400 3.0 0.36 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

SCMT 09T308 – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


85

TURNING

FProductivity



T00032401.204.7612SNMA 120412 LT 1005

T00032390.804.7612SNMA 120408 LT 1005

Application Guide

Strong edge preparation mainly for gray cast iron. For general purpose turning, facing and boring operations.

Fixing

S N Ml

Shape

90°m

Ø d0°

Clearance Angle Toleranced ± 0.08m ± 0.13s ± 0.13

s

SNMA

86


SNMA 120408 – LT 1005

SNMA 120412 – LT 1005


15 150 HB 0.7 6.0 0.20 0.60 1.7 270 450 33.5 00.40 3350

15 200 HB 0.7 6.0 0.20 0.58 1.5 200 320 33.5 00.40 2250

16 250 HB 0.7 6.0 0.20 0.56 1.5 170 240 33.5 00.40 2220

17,19 150 HB 0.7 6.0 0.20 0.52 1.3 130 260 33.0 00.30 2240

17,19 200 HB 0.7 6.0 0.20 0.50 1.1 130 230 33.0 00.30 2210

18,20 250 HB 0.7 6.0 0.20 0.48 1.0 130 190 33.0 00.30 1180



GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8


15 150 HB 0.7 6.0 0.20 0.40 1.4 270 450 33.5 00.32 3350

15 200 HB 0.7 6.0 0.20 0.38 1.2 200 320 33.5 00.32 2250

16 250 HB 0.7 6.0 0.20 0.36 1.2 170 240 33.5 00.32 2220

17,19 150 HB 0.7 6.0 0.20 0.40 1.0 130 260 22.5 00.30 2240

17,19 200 HB 0.7 6.0 0.20 0.38 0.9 130 230 22.5 00.30 2210

18,20 250 HB 0.7 6.0 0.20 0.36 0.8 130 190 22.5 00.30 1180



GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters







Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


87

TURNING

Stainless Steel

VC

NX-CNMP-TNMP-WNMP



FProductivity

S N M Gl

Shape

90°m

Ø d0°

Clearance Angle Fixing,Chipbreaker

ss

Toleranced ± 0.08m ± 0.13s ± 0.13

F M R

Application Guide



T00003231.204.7612SNMG 120412 NN LT 10

T00003220.804.7612SNMG 120408 NN LT 10

F M R

Application Guide


T00019221.204.7612SNMG 120412 NN LT 1000

T00030110.804.7612SNMG 120408 NX LT 1000

T00019210.804.7612SNMG 120408 NN LT 1000


Square inserts with strong cutting edge. Suitable for roughing operations.

NN chipbreaker NX chipbreaker

SNMG

88

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


SNMG 120408 NX LT 1025

SNMG 120412 NN LT 1025

F M R

Application Guide


T00040781.204.7612SNMG 120412 NN LT 1005

T00040770.804.7612SNMG 120408 NX LT 1005

T00040760.804.7612SNMG 120408 NN LT 1005


F M R

Application Guide


T00041361.204.7612

T00041340.804.7612

T00041330.804.7612SNMG 120408 NN LT 1025


S N M G

VC

Productivity NX-CNMP-TNMP-WNMP


NN chipbreaker NX chipbreaker

LT 1005

89



1 125 HB 0.5 5.0 0.30 0.70 2.54 180 330 33.0 0.50 2240

2 190 HB 0.5 5.0 0.30 0.70 2.54 180 280 33.0 0.50 2220

3 250 HB 0.5 5.0 0.30 0.63 2.12 180 250 33.0 0.50 2200

6 180 HB 0.5 5.0 0.30 0.63 1.69 120 280 33.0 0.45 2200

4,6 230 HB 0.5 4.0 0.30 0.63 1.69 120 250 33.0 0.45 1180

5,7 280 HB 0.5 4.0 0.25 0.56 1.69 120 210 33.0 0.43 1150

8 350 HB 0.5 3.5 0.25 0.56 1.41 120 180 33.0 0.43 1130

10 220 HB 0.5 4.0 0.25 0.56 1.69 70 190 22.5 0.43 1140

10 280 HB 0.5 4.0 0.25 0.56 1.69 70 150 22.5 0.43 1120

11 320 HB 0.5 3.0 0.25 0.49 1.13 70 130 22.5 0.40 1100

11 350 HB 0.5 3.0 0.25 0.49 1.13 70 110 22.5 0.40 990

14 180 HB 0.5 5.0 0.28 0.56 1.69 170 270 33.0 0.50 1190

14 240 HB 0.5 5.0 0.28 0.56 1.41 160 220 33.0 0.45 1170

14 290 HB 0.5 4.0 0.25 0.49 1.13 80 150 22.5 0.40 1100

14 310 HB 0.5 4.0 0.25 0.49 1.13 70 140 22.5 0.40 990

12 200 HB 0.5 5.0 0.31 0.56 1.41 170 250 33.0 0.45 1190

13 42 HRc 0.5 4.0 0.31 0.56 1.41 120 190 22.5 0.45 1130

15 150 HB 0.5 5.0 0.21 0.84 2.82 170 250 33.0 0.50 2200

15 200 HB 0.5 5.0 0.21 0.84 2.54 160 230 33.0 0.50 1180

16 250 HB 0.5 5.0 0.21 0.77 2.54 150 210 33.0 0.50 1160

17,19 150 HB 0.5 5.0 0.21 0.70 2.12 120 250 33.0 0.43 1180

17,19 200 HB 0.5 5.0 0.21 0.70 1.83 120 230 33.0 0.43 1160

18,20 250 HB 0.5 5.0 0.21 0.70 1.69 120 190 33.0 0.43 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.28 0.49 0.99 25 45 22.0 0.40 332

33 Inconel 700 250 HB 0.5 3.0 0.28 0.49 0.99 25 45 22.0 0.40 330

34 Stellite 21 350 HB 0.5 3.0 0.28 0.49 0.99 23 40 22.0 0.40 228

36 TiAl6V4 - 0.5 4.0 0.28 0.56 1.13 45 65 22.0 0.47 555

37 T40 - 0.5 3.0 0.28 0.49 0.99 35 55 22.0 0.43 445

38 45 HRc 0.5 2.5 0.16 0.42 0.85 50 100 22.0 0.36 880

38 50 HRc 0.5 2.0 0.16 0.35 0.56 40 90 11.5 0.28 770

38 55 HRc 0.5 1.5 0.16 0.28 0.42 40 80 11.0 0.26 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.28 0.80 2.50 200 400 3.0 0.57 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Har

dene

d M

at.

Steel

11

GGG40, GGG70, 50005

Hig

h Te

mp.

Allo

ys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cas

t Ir

on


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Sta

inle

ss S

teel


X5CrNi18-9

Duplex 5


Ste

el


Low alloyed

D.O.C. [mm]

2



SNMG 120408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






Values for lead angle (Kr)=45°; For lead angle (Kr)=75°, please limit feed to 75% of the recommended

90


SNMG 120408 NN – LT 1025


1 125 HB 0.5 5.0 0.30 0.70 2.54 90 330 33.0 0.54 2240

2 190 HB 0.5 5.0 0.30 0.70 2.54 90 280 33.0 0.50 2220

3 250 HB 0.5 5.0 0.30 0.63 2.12 90 250 33.0 0.47 2200

6 180 HB 0.5 5.0 0.30 0.63 1.69 60 280 33.0 0.45 2200

4,6 230 HB 0.5 4.0 0.30 0.63 1.69 60 250 33.0 0.45 1180

5,7 280 HB 0.5 4.0 0.25 0.56 1.69 60 210 33.0 0.43 1150

8 350 HB 0.5 3.5 0.25 0.56 1.41 60 180 22.7 0.43 1130

10 220 HB 0.5 4.0 0.25 0.56 1.69 35 190 22.5 0.43 1140

10 280 HB 0.5 4.0 0.25 0.56 1.69 35 150 22.5 0.43 1120

11 320 HB 0.5 3.0 0.25 0.49 1.13 35 130 22.2 0.40 1100

11 350 HB 0.5 3.0 0.25 0.49 1.13 35 110 22.2 0.40 990

14 180 HB 0.5 5.0 0.28 0.56 1.69 85 270 33.0 0.36 1190

14 240 HB 0.5 5.0 0.28 0.56 1.41 80 220 33.0 0.31 1170

14 290 HB 0.5 4.0 0.25 0.49 1.13 40 150 22.5 0.34 1100

14 310 HB 0.5 4.0 0.25 0.49 1.13 35 140 22.5 0.34 990

12 200 HB 0.5 5.0 0.25 0.56 0.99 85 250 22.5 0.28 1190

13 42 HRc 0.5 4.0 0.25 0.56 0.99 60 190 22.2 0.28 1130

17,19 150 HB 0.5 5.0 0.21 0.70 2.12 60 250 33.0 0.43 1180

17,19 200 HB 0.5 5.0 0.21 0.70 1.83 60 230 33.0 0.43 1160

18,20 250 HB 0.5 5.0 0.21 0.70 1.69 60 190 33.0 0.43 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

SNMG 120408 NN – LT 1005


1 125 HB 0.5 5.0 0.30 0.70 2.54 180 430 33.0 0.54 2265

2 190 HB 0.5 5.0 0.30 0.70 2.54 180 365 33.0 0.50 2240

3 250 HB 0.5 5.0 0.30 0.63 2.12 180 325 33.0 0.47 2220

6 180 HB 0.5 5.0 0.30 0.63 1.69 120 365 33.0 0.45 2220

4,6 230 HB 0.5 4.0 0.30 0.63 1.69 120 325 33.0 0.45 2200

5,7 280 HB 0.5 4.0 0.25 0.56 1.69 120 275 33.0 0.43 1165

8 350 HB 0.5 3.5 0.25 0.56 1.41 120 235 22.7 0.43 1145

10 220 HB 0.5 4.0 0.25 0.56 1.69 70 245 22.5 0.43 1155

10 280 HB 0.5 4.0 0.25 0.56 1.69 70 195 22.5 0.43 1130

11 320 HB 0.5 3.0 0.25 0.49 1.13 70 170 22.2 0.40 1110

11 350 HB 0.5 3.0 0.25 0.49 1.13 70 145 22.2 0.40 1100

15 150 HB 0.5 5.0 0.21 0.84 2.82 170 325 33.0 0.50 2220

15 200 HB 0.5 5.0 0.21 0.84 2.54 160 300 33.0 0.50 2200

16 250 HB 0.5 5.0 0.21 0.77 2.54 150 275 33.0 0.50 1175

17,19 150 HB 0.5 5.0 0.21 0.70 2.12 120 325 33.0 0.43 2200

17,19 200 HB 0.5 5.0 0.21 0.70 1.83 120 300 33.0 0.43 1175

18,20 250 HB 0.5 5.0 0.21 0.70 1.69 120 245 33.0 0.43 1155

38 45 HRc 0.5 2.5 0.16 0.42 0.85 50 130 22.0 0.36 990

38 50 HRc 0.5 2.0 0.16 0.35 0.56 40 115 11.5 0.28 775

38 55 HRc 0.5 1.5 0.16 0.28 0.42 40 105 11.0 0.26 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular



91



1 125 HB 0.5 5.0 0.26 0.70 2.40 180 330 33.0 0.47 2240

2 190 HB 0.5 5.0 0.26 0.70 2.40 180 280 33.0 0.47 2220

3 250 HB 0.5 5.0 0.26 0.63 2.00 180 250 33.0 0.47 2200

6 180 HB 0.5 5.0 0.26 0.63 1.60 120 280 33.0 0.43 2200

4,6 230 HB 0.5 4.0 0.26 0.63 1.60 120 250 33.0 0.43 1180

5,7 280 HB 0.5 4.0 0.22 0.56 1.60 120 210 33.0 0.41 1150

8 350 HB 0.5 3.5 0.22 0.56 1.35 120 180 33.0 0.41 1130

10 220 HB 0.5 4.0 0.22 0.56 1.60 70 190 22.5 0.41 1140

10 280 HB 0.5 4.0 0.22 0.56 1.60 70 150 22.5 0.41 1120

11 320 HB 0.5 3.0 0.22 0.49 1.05 70 130 22.5 0.38 1100

11 350 HB 0.5 3.0 0.22 0.49 1.05 70 110 22.5 0.38 990

14 180 HB 0.5 5.0 0.25 0.56 1.60 170 270 33.0 0.34 1190

14 240 HB 0.5 5.0 0.25 0.56 1.35 160 220 33.0 0.30 1170

14 290 HB 0.5 4.0 0.22 0.49 1.05 80 150 22.5 0.38 1100

14 310 HB 0.5 4.0 0.22 0.49 1.05 70 140 22.5 0.38 990

12 200 HB 0.5 5.0 0.27 0.56 1.35 170 250 22.5 0.41 1190

13 42 HRc 0.5 4.0 0.27 0.56 1.35 120 190 22.5 0.34 1130

15 150 HB 0.5 5.0 0.18 0.84 2.70 170 250 33.0 0.47 2200

15 200 HB 0.5 5.0 0.18 0.84 2.40 160 230 33.0 0.47 1180

16 250 HB 0.5 5.0 0.18 0.77 2.40 150 210 33.0 0.47 1160

17,19 150 HB 0.5 5.0 0.18 0.70 2.00 120 250 33.0 0.41 1180

17,19 200 HB 0.5 5.0 0.18 0.70 1.75 120 230 33.0 0.41 1160

18,20 250 HB 0.5 5.0 0.18 0.70 1.60 120 190 33.0 0.41 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.25 0.49 0.95 25 45 22.0 0.38 330

33 Inconel 700 250 HB 0.5 3.0 0.25 0.49 0.95 25 45 22.0 0.38 330

34 Stellite 21 350 HB 0.5 3.0 0.25 0.49 0.95 25 40 22.0 0.38 330

36 TiAl6V4 - 0.5 4.0 0.25 0.56 1.05 45 65 22.0 0.45 555

37 T40 - 0.5 3.0 0.25 0.49 0.95 35 55 22.0 0.41 445

38 45 HRc 0.5 2.5 0.14 0.42 0.80 50 100 22.0 0.34 880

38 50 HRc 0.5 2.0 0.14 0.35 0.55 40 90 11.5 0.27 770

38 55 HRc 0.5 1.5 0.14 0.28 0.40 40 80 11.0 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.25 0.84 2.40 200 400 33.0 0.54 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

Cast

Iron


No30B


3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

2

Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

High alloyed


Low alloyed

St

eel

X2CrNiN23-4, S31500


SNMG 120408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







92


SNMG 120408 NX – LT 1025


1 125 HB 0.5 5.0 0.26 0.70 2.41 90 330 33.0 0.51 2240

2 190 HB 0.5 5.0 0.26 0.70 2.41 90 280 33.0 0.47 2220

3 250 HB 0.5 5.0 0.26 0.63 2.01 90 250 33.0 0.45 2200

6 180 HB 0.5 5.0 0.26 0.63 1.61 60 280 33.0 0.43 2200

4,6 230 HB 0.5 4.0 0.26 0.63 1.61 60 250 33.0 0.43 1180

5,7 280 HB 0.5 4.0 0.22 0.56 1.61 60 210 33.0 0.41 1150

8 350 HB 0.5 3.5 0.22 0.56 1.34 60 180 22.7 0.41 1130

10 220 HB 0.5 4.0 0.22 0.56 1.61 35 190 22.5 0.41 1140

10 280 HB 0.5 4.0 0.22 0.56 1.61 35 150 22.5 0.41 1120

11 320 HB 0.5 3.0 0.22 0.49 1.07 35 130 22.2 0.38 1100

11 350 HB 0.5 3.0 0.22 0.49 1.07 35 110 22.2 0.38 990

14 180 HB 0.5 5.0 0.25 0.56 1.61 85 270 33.0 0.34 1190

14 240 HB 0.5 5.0 0.25 0.56 1.34 80 220 33.0 0.30 1170

14 290 HB 0.5 4.0 0.22 0.49 1.07 40 150 22.5 0.32 1100

14 310 HB 0.5 4.0 0.22 0.49 1.07 35 140 22.5 0.32 990

12 200 HB 0.5 5.0 0.22 0.56 0.94 85 250 22.5 0.27 1190

13 42 HRc 0.5 4.0 0.22 0.56 0.94 60 190 22.2 0.27 1130

17,19 150 HB 0.5 5.0 0.18 0.70 2.01 60 250 33.0 0.41 1180

17,19 200 HB 0.5 5.0 0.18 0.70 1.74 60 230 33.0 0.41 1160

18,20 250 HB 0.5 5.0 0.18 0.70 1.61 60 190 33.0 0.41 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

SNMG 120408 NX – LT 1005


1 125 HB 0.5 5.0 0.26 0.70 2.41 180 430 33.0 0.51 2265

2 190 HB 0.5 5.0 0.26 0.70 2.41 180 365 33.0 0.47 2240

3 250 HB 0.5 5.0 0.26 0.63 2.01 180 325 33.0 0.45 2220

6 180 HB 0.5 5.0 0.26 0.63 1.61 120 365 33.0 0.43 2220

4,6 230 HB 0.5 4.0 0.26 0.63 1.61 120 325 33.0 0.43 2200

5,7 280 HB 0.5 4.0 0.22 0.56 1.61 120 275 33.0 0.41 1165

8 350 HB 0.5 3.5 0.22 0.56 1.34 120 235 22.7 0.41 1145

10 220 HB 0.5 4.0 0.22 0.56 1.61 70 245 22.5 0.41 1155

10 280 HB 0.5 4.0 0.22 0.56 1.61 70 195 22.5 0.41 1130

11 320 HB 0.5 3.0 0.22 0.49 1.07 70 170 22.2 0.38 1110

11 350 HB 0.5 3.0 0.22 0.49 1.07 70 145 22.2 0.38 1100

15 150 HB 0.5 5.0 0.18 0.84 2.68 170 325 33.0 0.47 2220

15 200 HB 0.5 5.0 0.18 0.84 2.41 160 300 33.0 0.47 2200

16 250 HB 0.5 5.0 0.18 0.77 2.41 150 275 33.0 0.47 1175

17,19 150 HB 0.5 5.0 0.18 0.70 2.01 120 325 33.0 0.41 2200

17,19 200 HB 0.5 5.0 0.18 0.70 1.74 120 300 33.0 0.41 1175

18,20 250 HB 0.5 5.0 0.18 0.70 1.61 120 245 33.0 0.41 1155

38 45 HRc 0.5 2.5 0.14 0.42 0.80 50 130 22.0 0.34 990

38 50 HRc 0.5 2.0 0.14 0.35 0.54 40 115 11.5 0.27 775

38 55 HRc 0.5 1.5 0.14 0.28 0.40 40 105 11.0 0.24 665



X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



Low alloyed 2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular



93



1 125 HB 0.7 6.0 0.37 0.95 3.96 180 330 44.0 0.65 2240

2 190 HB 0.7 6.0 0.37 0.95 3.96 180 280 44.0 0.65 2220

3 250 HB 0.7 6.0 0.37 0.86 3.30 180 250 44.0 0.65 2200

6 180 HB 0.7 6.0 0.37 0.86 2.64 120 280 44.0 0.60 2200

4,6 230 HB 0.7 4.8 0.37 0.86 2.64 120 250 44.0 0.60 1180

5,7 280 HB 0.7 4.8 0.32 0.76 2.64 120 210 44.0 0.56 1150

8 350 HB 0.7 4.2 0.32 0.76 2.40 120 180 44.0 0.56 1130

10 220 HB 0.7 4.8 0.32 0.76 2.64 70 190 33.4 0.56 1140

10 280 HB 0.7 4.8 0.32 0.76 2.64 70 150 33.4 0.56 1120

11 320 HB 0.7 3.6 0.32 0.67 1.76 70 130 33.4 0.52 1100

11 350 HB 0.7 3.6 0.32 0.67 1.76 70 110 33.4 0.52 990

14 180 HB 0.7 6.0 0.35 0.76 2.64 170 270 44.0 0.58 1190

14 240 HB 0.7 6.0 0.35 0.76 2.20 160 220 44.0 0.52 1170

14 290 HB 0.7 4.8 0.32 0.67 1.76 80 150 33.4 0.46 1100

14 310 HB 0.7 4.8 0.32 0.67 1.76 70 140 33.4 0.46 990

12 200 HB 0.7 6.0 0.39 0.76 2.20 170 250 44.0 0.55 1190

13 42 HRc 0.7 4.8 0.39 0.76 2.20 120 190 33.0 0.50 1130

15 150 HB 0.7 6.0 0.30 1.14 4.40 170 250 44.0 0.65 2200

15 200 HB 0.7 6.0 0.30 1.14 3.96 160 230 44.0 0.65 1180

16 250 HB 0.7 6.0 0.30 1.05 3.96 150 210 44.0 0.65 1160

17,19 150 HB 0.7 6.0 0.30 0.95 3.30 120 250 44.0 0.56 1180

17,19 200 HB 0.7 6.0 0.30 0.95 2.86 120 230 44.0 0.56 1160

18,20 250 HB 0.7 6.0 0.30 0.95 2.64 120 190 44.0 0.56 1140

31,32 Incoloy 800 240 HB 0.7 3.6 0.35 0.67 1.54 25 45 22.7 0.52 332

33 Inconel 700 250 HB 0.7 3.6 0.35 0.67 1.54 25 45 22.7 0.52 330

34 Stellite 21 350 HB 0.7 3.6 0.35 0.67 1.54 23 40 22.7 0.52 228

36 TiAl6V4 - 0.7 4.8 0.35 0.76 1.76 45 65 22.7 0.58 555

37 T40 - 0.7 3.6 0.35 0.67 1.54 35 55 22.7 0.52 445

38 45 HRc 0.7 3.0 0.19 0.57 1.32 50 100 22.7 0.47 880

38 50 HRc 0.7 2.4 0.19 0.48 0.88 40 90 22.0 0.37 770

38 55 HRc 0.7 1.8 0.19 0.38 0.66 40 80 11.3 0.33 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.35 1.14 4.30 200 400 4.0 0.80 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

Ste

el


Low alloyed 2

SNMG 120412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







94



1 125 HB 0.7 6.0 0.37 0.95 3.96 90 330 44.0 00.71 2240

2 190 HB 0.7 6.0 0.37 0.95 3.96 90 280 44.0 00.65 2220

3 250 HB 0.7 6.0 0.37 0.86 3.30 90 250 44.0 00.61 2200

6 180 HB 0.7 6.0 0.37 0.86 2.64 60 280 44.0 00.60 2200

4,6 230 HB 0.7 4.8 0.37 0.86 2.64 60 250 44.0 00.60 1180

5,7 280 HB 0.7 4.8 0.32 0.76 2.64 60 210 44.0 00.56 1150

8 350 HB 0.7 4.2 0.32 0.76 2.20 60 180 33.6 00.56 1130

10 220 HB 0.7 4.8 0.32 0.76 2.64 35 190 33.4 00.56 1140

10 280 HB 0.7 4.8 0.32 0.76 2.64 35 150 33.4 00.56 1120

11 320 HB 0.7 3.6 0.32 0.67 1.76 35 130 22.9 00.52 1100

11 350 HB 0.7 3.6 0.32 0.67 1.76 35 110 22.9 00.52 990

14 180 HB 0.7 6.0 0.35 0.76 2.64 85 270 44.0 00.47 1190

14 240 HB 0.7 6.0 0.35 0.76 2.20 80 220 44.0 00.41 1170

14 290 HB 0.7 4.8 0.32 0.67 1.76 40 150 33.4 00.45 1100

14 310 HB 0.7 4.8 0.32 0.67 1.76 35 140 33.4 00.45 990

12 200 HB 0.7 6.0 0.32 0.76 1.54 85 250 33.4 00.37 1190

13 42 HRc 0.7 4.8 0.32 0.76 1.54 60 190 22.9 00.37 1130

17,19 150 HB 0.7 6.0 0.26 0.95 3.30 60 250 44.0 00.56 1180

17,19 200 HB 0.7 6.0 0.26 0.95 2.86 60 230 44.0 00.56 1160

18,20 250 HB 0.7 6.0 0.26 0.95 2.64 60 190 44.0 00.56 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

SNMG 120412 NN – LT 1025

SNMG 120412 NN – LT 1005


1 125 HB 0.7 6.0 0.37 0.95 3.96 180 430 44.0 00.71 2265

2 190 HB 0.7 6.0 0.37 0.95 3.96 180 365 44.0 00.65 2240

3 250 HB 0.7 6.0 0.37 0.86 3.30 180 325 44.0 00.61 2220

6 180 HB 0.7 6.0 0.37 0.86 2.64 120 365 44.0 00.60 2220

4,6 230 HB 0.7 4.8 0.37 0.86 2.64 120 325 44.0 00.60 2200

5,7 280 HB 0.7 4.8 0.32 0.76 2.64 120 275 44.0 00.56 1165

8 350 HB 0.7 4.2 0.32 0.76 2.20 120 235 33.6 00.56 1145

10 220 HB 0.7 4.8 0.32 0.76 2.64 70 245 33.4 00.56 1155

10 280 HB 0.7 4.8 0.32 0.76 2.64 70 195 33.4 00.56 1130

11 320 HB 0.7 3.6 0.32 0.67 1.76 70 170 22.9 00.52 1110

11 350 HB 0.7 3.6 0.32 0.67 1.76 70 145 22.9 00.52 1100

15 150 HB 0.7 6.0 0.26 1.14 4.40 170 325 44.0 00.65 2220

15 200 HB 0.7 6.0 0.26 1.14 3.96 160 300 44.0 00.65 2200

16 250 HB 0.7 6.0 0.26 1.05 3.96 150 275 44.0 00.65 1175

17,19 150 HB 0.7 6.0 0.26 0.95 3.30 120 325 44.0 00.56 2200

17,19 200 HB 0.7 6.0 0.26 0.95 2.86 120 300 44.0 00.56 1175

18,20 250 HB 0.7 6.0 0.26 0.95 2.64 120 245 44.0 00.56 1155

38 45 HRc 0.7 3.0 0.19 0.57 1.32 50 130 22.7 00.47 990

38 50 HRc 0.7 2.4 0.19 0.48 0.88 40 115 22.0 00.37 775

38 55 HRc 0.7 1.8 0.19 0.38 0.66 40 105 11.3 00.33 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular




fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


95

TURNING

Stainless Steel

VC

T C M T7°


l

m

Ø d

Fixing,Chipbreaker

60°

s



T00017741.203.9716TCMT 16T312 NN LT 10

T00000680.803.9716TCMT 16T308 NN LT 10

T00004790.403.9716TCMT 16T304 NN LT 10

T00004780.802.3811TCMT 110208 NN LT 10

T00004770.402.3811TCMT 110204 NN LT 10

F M

Application Guide


T00019291.203.9716TCMT 16T312 NN LT 1000

T00019280.803.9716TCMT 16T308 NN LT 1000

T00019270.403.9716TCMT 16T304 NN LT 1000

T00019250.802.3811TCMT 110208 NN LT 1000

T00019240.402.3811TCMT 110204 NN LT 1000

R


60

60° triangle shape inserts with positive rake angle. Suitable for boring and internal turning operations.

TCMT

Application Guide

96



1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300

2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260

3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240

6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260

4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240

5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200

8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180

10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180

10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140

11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120

11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110

14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260

14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210

14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140

14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140

12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240

13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180

15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240

15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220

16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200

17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240

17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220

18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180

31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335

36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660

37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550

38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990

38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880

38 55 HRc 0.3 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

TCMT 110204 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






97



1 125 HB 0.2 2.1 0.08 0.20 0.37 180 330 11.0 0.25 3300

2 190 HB 0.2 1.8 0.08 0.19 0.32 180 280 11.0 0.25 2260

3 250 HB 0.2 1.8 0.08 0.17 0.30 180 250 11.0 0.25 2240

6 180 HB 0.2 1.8 0.08 0.17 0.31 120 280 11.0 0.21 2260

4,6 230 HB 0.2 1.8 0.08 0.17 0.30 120 250 11.0 0.21 2240

5,7 280 HB 0.2 1.4 0.08 0.15 0.25 120 210 11.0 0.21 2200

8 350 HB 0.2 1.4 0.08 0.15 0.22 120 180 11.0 0.21 1180

10 220 HB 0.2 1.8 0.07 0.15 0.25 70 190 11.0 0.17 1180

10 280 HB 0.2 1.8 0.07 0.14 0.25 70 150 11.0 0.17 1140

11 320 HB 0.2 1.4 0.07 0.12 0.20 70 130 11.0 0.17 1120

11 350 HB 0.2 1.4 0.07 0.12 0.16 70 110 11.0 0.17 1110

14 180 HB 0.2 1.8 0.08 0.15 0.20 170 270 11.0 0.17 2260

14 240 HB 0.2 1.8 0.08 0.15 0.16 160 220 11.0 0.17 2210

14 290 HB 0.2 1.4 0.07 0.12 0.12 80 150 11.0 0.17 1140

14 310 HB 0.2 1.4 0.07 0.12 0.12 70 140 11.0 0.17 1140

12 200 HB 0.2 1.8 0.08 0.15 0.20 170 250 11.0 0.21 2240

13 42 HRc 0.2 1.4 0.08 0.14 0.16 120 190 11.0 0.17 1180

15 150 HB 0.2 2.1 0.06 0.17 0.40 170 250 11.0 0.25 2240

15 200 HB 0.2 2.1 0.06 0.17 0.37 160 230 11.0 0.25 2220

16 250 HB 0.2 2.1 0.06 0.17 0.37 150 210 11.0 0.25 2200

17,19 150 HB 0.2 1.8 0.06 0.15 0.30 120 250 11.0 0.21 2240

17,19 200 HB 0.2 1.8 0.06 0.15 0.25 120 230 11.0 0.21 2220

18,20 250 HB 0.2 1.8 0.06 0.15 0.25 120 190 11.0 0.21 1180

31,32 Incoloy 800 240 HB 0.2 1.4 0.08 0.13 0.16 25 50 11.0 0.17 440

33 Inconel 700 250 HB 0.2 1.4 0.08 0.13 0.16 25 50 11.0 0.17 440

34 Stellite 21 350 HB 0.2 1.4 0.08 0.13 0.16 23 45 11.0 0.17 335

36 TiAl6V4 - 0.2 1.4 0.08 0.14 0.20 45 65 11.0 0.20 660

37 T40 - 0.2 1.4 0.08 0.12 0.16 35 60 11.0 0.17 550

38 45 HRc 0.2 1.3 0.04 0.10 0.12 50 100 00.8 0.15 990

38 50 HRc 0.2 1.1 0.04 0.09 0.11 40 90 00.6 0.13 880

38 55 HRc 0.2 1.0 0.04 0.08 0.08 40 80 00.5 0.10 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.2 2.8 0.08 0.26 0.43 200 400 11.0 0.28 350

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

TCMT 110208 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






98



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

TCMT 16T304 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






99



1 125 HB 0.5 5.0 0.21 0.43 1.62 180 330 33.0 0.30 2240

2 190 HB 0.5 5.0 0.21 0.43 1.62 180 280 33.0 0.30 2220

3 250 HB 0.5 5.0 0.21 0.38 1.35 180 250 33.0 0.30 2200

6 180 HB 0.5 5.0 0.21 0.38 1.08 120 280 33.0 0.27 2200

4,6 230 HB 0.5 4.0 0.21 0.38 1.08 120 250 33.0 0.27 1180

5,7 280 HB 0.5 4.0 0.18 0.34 1.08 120 210 33.0 0.26 1150

8 350 HB 0.5 3.5 0.18 0.34 0.90 120 180 33.0 0.26 1130

10 220 HB 0.5 4.0 0.18 0.34 1.08 70 190 22.5 0.26 1140

10 280 HB 0.5 4.0 0.18 0.34 1.08 70 150 22.5 0.26 1120

11 320 HB 0.5 3.0 0.18 0.30 0.72 70 130 22.5 0.24 1100

11 350 HB 0.5 3.0 0.18 0.30 0.72 70 110 22.5 0.24 990

14 180 HB 0.5 5.0 0.20 0.34 1.08 170 270 33.0 0.30 2200

14 240 HB 0.5 5.0 0.20 0.34 0.90 160 220 33.0 0.27 1180

14 290 HB 0.5 4.0 0.18 0.30 0.72 80 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.30 0.72 70 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.22 0.34 0.90 170 250 33.0 0.27 1190

13 42 HRc 0.5 4.0 0.22 0.34 0.90 120 190 22.5 0.27 1130

15 150 HB 0.5 5.0 0.15 0.51 1.80 170 250 33.0 0.30 2200

15 200 HB 0.5 5.0 0.15 0.51 1.62 160 230 33.0 0.30 1180

16 250 HB 0.5 5.0 0.15 0.47 1.62 150 210 33.0 0.30 1160

17,19 150 HB 0.5 5.0 0.15 0.43 1.35 120 250 33.0 0.26 1180

17,19 200 HB 0.5 5.0 0.15 0.43 1.17 120 230 33.0 0.26 1160

18,20 250 HB 0.5 5.0 0.15 0.43 1.08 120 190 33.0 0.26 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.30 0.63 25 45 22.0 0.24 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.30 0.63 25 45 22.0 0.24 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.30 0.63 23 40 22.0 0.24 228

36 TiAl6V4 - 0.5 4.0 0.20 0.34 0.72 45 65 22.0 0.28 555

37 T40 - 0.5 3.0 0.20 0.30 0.63 35 55 22.0 0.26 445

38 45 HRc 0.5 2.5 0.11 0.26 0.54 50 100 22.0 0.21 880

38 50 HRc 0.5 2.0 0.11 0.21 0.36 40 90 11.5 0.17 770

38 55 HRc 0.5 1.5 0.11 0.17 0.27 40 80 11.0 0.15 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.51 1.60 200 400 33.0 0.34 280

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based


No30B

Malleable & Nodular

10

8



X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

Non-alloyed

Low alloyed

TCMT 16T308 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






100



1 125 HB 0.5 5.0 0.21 0.48 1.94 180 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.48 1.94 180 280 33.0 0.38 2220

3 250 HB 0.5 5.0 0.21 0.43 1.62 180 250 33.0 0.38 2200

6 180 HB 0.5 5.0 0.21 0.43 1.30 120 280 33.0 0.35 2200

4,6 230 HB 0.5 4.0 0.21 0.43 1.30 120 250 33.0 0.35 1180

5,7 280 HB 0.5 4.0 0.18 0.38 1.30 120 210 33.0 0.32 1150

8 350 HB 0.5 3.5 0.18 0.38 1.08 120 180 33.0 0.32 1130

10 220 HB 0.5 4.0 0.18 0.38 1.30 70 190 22.5 0.32 1140

10 280 HB 0.5 4.0 0.18 0.38 1.30 70 150 22.5 0.32 1120

11 320 HB 0.5 3.0 0.18 0.33 0.86 70 130 22.5 0.30 1100

11 350 HB 0.5 3.0 0.18 0.33 0.86 70 110 22.5 0.30 990

14 180 HB 0.5 5.0 0.20 0.38 1.30 170 270 33.0 0.38 2200

14 240 HB 0.5 5.0 0.20 0.38 1.08 160 220 33.0 0.35 1180

14 290 HB 0.5 4.0 0.18 0.33 0.86 80 150 22.5 0.30 1100

14 310 HB 0.5 4.0 0.18 0.33 0.86 70 140 22.5 0.30 990

12 200 HB 0.5 5.0 0.22 0.38 1.08 170 250 33.0 0.35 1190

13 42 HRc 0.5 4.0 0.22 0.38 1.08 120 190 22.5 0.35 1130

15 150 HB 0.5 5.0 0.15 0.57 2.16 170 250 33.0 0.38 2200

15 200 HB 0.5 5.0 0.15 0.57 1.94 160 230 33.0 0.38 1180

16 250 HB 0.5 5.0 0.15 0.52 1.94 150 210 33.0 0.38 1160

17,19 150 HB 0.5 5.0 0.15 0.48 1.62 120 250 33.0 0.32 1180

17,19 200 HB 0.5 5.0 0.15 0.48 1.40 120 230 33.0 0.32 1160

18,20 250 HB 0.5 5.0 0.15 0.48 1.30 120 190 33.0 0.32 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.33 0.76 25 45 22.0 0.30 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.33 0.76 25 45 22.0 0.30 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.33 0.76 23 40 22.0 0.30 228

36 TiAl6V4 - 0.5 4.0 0.20 0.38 0.86 45 65 22.0 0.36 555

37 T40 - 0.5 3.0 0.20 0.33 0.76 35 55 22.0 0.32 445

38 45 HRc 0.5 2.5 0.11 0.29 0.65 50 100 22.0 0.27 880

38 50 HRc 0.5 2.0 0.11 0.24 0.43 40 90 11.5 0.22 770

38 55 HRc 0.5 1.5 0.11 0.19 0.32 40 80 11.0 0.19 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.57 1.90 200 400 33.0 0.43 280

Non-alloyed

Low alloyed

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500



X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based


No30B

Malleable & Nodular

10

8

TCMT 16T312 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


101

TURNING

FProductivity



T00032381.204.7616TNMA 160412 LT 1005


T00028370.804.7616TNMA 160408 LT 1005

Shape Tolerance

0°

Clearance Angle Fixing, Chipbreaker

l

m

Ø d60°

s ± 0.13For l = 16, d ± 0.05 m ± 0.08 For l = 22, d ± 0.08 m ± 0.13

s

Application Guide

TNMA

102


TNMA 160408 – LT 1005

TNMA 160412 – LT 1005


15 150 HB 0.7 5.0 0.15 0.38 1.3 270 450 33.5 00.33 3350

15 200 HB 0.7 5.0 0.15 0.35 1.2 200 320 33.5 00.33 2250

16 250 HB 0.7 5.0 0.15 0.32 1.2 170 240 33.5 00.33 2220

17,19 150 HB 0.7 5.0 0.15 0.38 1.3 130 260 22.5 00.30 2240

17,19 200 HB 0.7 5.0 0.15 0.35 1.2 130 230 22.5 00.30 2210

18,20 250 HB 0.7 5.0 0.15 0.32 1.2 130 190 22.5 00.30 1180



GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8


15 150 HB 0.7 5.0 0.15 0.35 1.3 270 450 33.2 00.30 3350

15 200 HB 0.7 5.0 0.15 0.33 1.2 200 320 33.2 00.30 2250

16 250 HB 0.7 5.0 0.15 0.30 1.2 170 240 33.2 00.30 2220

17,19 150 HB 0.7 5.0 0.15 0.35 1.0 130 260 22.5 00.28 2240

17,19 200 HB 0.7 5.0 0.15 0.33 0.9 130 230 22.5 00.28 2210

18,20 250 HB 0.7 5.0 0.15 0.30 0.8 130 190 22.5 00.28 1180



GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters







Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


103

TURNING

T N M G

Shape Tolerance

0°


l

m

Ø d60°

s ± 0.13For l = 16, d ± 0.05 m ± 0.08 For l = 22, d ± 0.08 m ± 0.13

ss

60°

60° triangle shape inserts. Suitable for general purpose turning and copying operations.

LT 10 and LT 1000


LT 10 and LT 1000

NX-CNMP-TNMP-WNMP



FProductivity

Stainless Steel

VC



T00017351.204.7622TNMG 220412 NN LT 10

T00001130.804.7622TNMG 220408 NN LT 10

T00018730.404.7622TNMG 220404 NN LT 10

T00017341.204.7616TNMG 160412 NN LT 10

T00000690.804.7616TNMG 160408 NN LT 10

T00004570.404.7616TNMG 160404 NN LT 10

Application Guide



T00019361.204.7622TNMG 220412 NN LT 1000

T00030130.804.7622TNMG 220408 NX LT 1000

T00019350.804.7622TNMG 220408 NN LT 1000

T00019340.404.7622TNMG 220404 NN LT 1000

T00019331.204.7616TNMG 160412 NN LT 1000

T00030120.804.7616TNMG 160408 NX LT 1000

T00019320.804.7616TNMG 160408 NN LT 1000

T00019310.404.7616TNMG 160404 NN LT 1000

Application Guide TNMGTNMG

104

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14




T00041441.204.7622TNMG 220412 NN LT 1025

T00041430.804.7622TNMG 220408 NX LT 1025

T00041420.804.7622TNMG 220408 NN LT 1025

T00041401.204.7616TNMG 160412 NN LT 1025

T00041390.804.7616TNMG 160408 NX LT 1025

T00041380.804.7616TNMG 160408 NN LT 1025

Application Guide



T00040881.204.7622TNMG 220412 NN LT 1005

T00040870.804.7622TNMG 220408 NX LT 1005

T00040860.804.7622TNMG 220408 NN LT 1005

T00040841.204.7616TNMG 160412 NN LT 1005

T00040830.804.7616TNMG 160408 NX LT 1005

T00040820.804.7616TNMG 160408 NN LT 1005

Application Guide

T N M G


NX-CNMP-TNMP-WNMP


Productivity

NX chipbreaker NM chipbreaker

105



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

TNMG 160404 NN – T 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






106



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

Non-alloyed

Low alloyed

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500



X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based


No30B

Malleable & Nodular

10

8

TNMG 160408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






107


TNMG 160408 NN – LT 1025


1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

TNMG 160408 NN – LT 1005


1 125 HB 0.5 5.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 105 11.0 0.18 665



St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

Cast

Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

108



1 125 HB 0.5 5.0 0.18 0.50 1.70 180 330 33.0 0.33 2240

2 190 HB 0.5 5.0 0.18 0.50 1.70 180 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.45 180 250 33.0 0.33 2200

6 180 HB 0.5 5.0 0.18 0.45 1.15 120 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.15 120 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.15 120 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 120 180 33.0 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.15 70 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.15 70 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.75 70 130 22.5 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.75 70 110 22.5 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.15 170 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 160 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.75 80 150 22.5 0.27 1100

14 310 HB 0.5 4.0 0.16 0.35 0.75 70 140 22.5 0.27 990

12 200 HB 0.5 5.0 0.19 0.40 0.95 170 250 22.5 0.29 1190

13 42 HRc 0.5 4.0 0.19 0.40 0.95 120 190 22.2 0.24 1130

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 250 33.0 0.33 2200

15 200 HB 0.5 5.0 0.13 0.60 1.70 160 230 33.0 0.33 1180

16 250 HB 0.5 5.0 0.13 0.55 1.70 150 210 33.0 0.33 1160

17,19 150 HB 0.5 5.0 0.13 0.50 1.45 120 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.25 120 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.15 120 190 33.0 0.29 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

33 Inconel 700 250 HB 0.5 3.0 0.18 0.35 0.65 25 45 22.0 0.27 330

34 Stellite 21 350 HB 0.5 3.0 0.18 0.35 0.65 25 40 22.0 0.27 330

36 TiAl6V4 - 0.5 4.0 0.18 0.40 0.75 45 65 22.0 0.31 555

37 T40 - 0.5 3.0 0.18 0.35 0.65 35 55 22.0 0.29 445

38 45 HRc 0.5 2.5 0.10 0.30 0.55 50 100 22.0 0.24 880

38 50 HRc 0.5 2.0 0.10 0.25 0.40 40 90 11.5 0.19 770

38 55 HRc 0.5 1.5 0.10 0.20 0.30 40 80 11.0 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.18 0.60 1.70 200 400 33.0 0.38 280

St

eel

Non-alloyed

Low alloyed

Material Group


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


2

1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]


Material Examples* HardnessVc [m/min]

Gr. N°

X2CrNiN23-4, S31500


Feed [mm/rev]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

TNMG 160408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






109


TNMG 160408 NX – LT 1025


1 125 HB 0.5 5.0 0.18 0.50 1.71 90 330 33.0 0.36 2240

2 190 HB 0.5 5.0 0.18 0.50 1.71 90 280 33.0 0.33 2220

3 250 HB 0.5 5.0 0.18 0.45 1.43 90 250 33.0 0.31 2200

6 180 HB 0.5 5.0 0.18 0.45 1.14 60 280 33.0 0.30 2200

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 60 250 33.0 0.30 1180

5,7 280 HB 0.5 4.0 0.16 0.40 1.14 60 210 33.0 0.29 1150

8 350 HB 0.5 3.5 0.16 0.40 0.95 60 180 22.7 0.29 1130

10 220 HB 0.5 4.0 0.16 0.40 1.14 35 190 22.5 0.29 1140

10 280 HB 0.5 4.0 0.16 0.40 1.14 35 150 22.5 0.29 1120

11 320 HB 0.5 3.0 0.16 0.35 0.76 35 130 22.2 0.27 1100

11 350 HB 0.5 3.0 0.16 0.35 0.76 35 110 22.2 0.27 990

14 180 HB 0.5 5.0 0.18 0.40 1.14 85 270 33.0 0.24 1190

14 240 HB 0.5 5.0 0.18 0.40 0.95 80 220 33.0 0.21 1170

14 290 HB 0.5 4.0 0.16 0.35 0.76 40 150 22.5 0.23 1100

14 310 HB 0.5 4.0 0.16 0.35 0.76 35 140 22.5 0.23 990

12 200 HB 0.5 5.0 0.16 0.40 0.67 85 250 22.5 0.19 1190

13 42 HRc 0.5 4.0 0.16 0.40 0.67 60 190 22.2 0.19 1130

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 60 250 33.0 0.29 1180

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 60 230 33.0 0.29 1160

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 60 190 33.0 0.29 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

TNMG 160408 NX – LT 1005


1 125 HB 0.5 5.0 0.18 0.50 1.71 180 430 33.0 0.36 2265

2 190 HB 0.5 5.0 0.18 0.50 1.71 180 365 33.0 0.33 2240

3 250 HB 0.5 5.0 0.18 0.45 1.43 180 325 33.0 0.31 2220

6 180 HB 0.5 5.0 0.18 0.45 1.14 120 365 33.0 0.30 2220

4,6 230 HB 0.5 4.0 0.18 0.45 1.14 120 325 33.0 0.30 2200

5,7 280 HB 0.5 4.0 0.15 0.40 1.14 120 275 33.0 0.29 1165

8 350 HB 0.5 3.5 0.15 0.40 0.95 120 235 22.7 0.29 1145

10 220 HB 0.5 4.0 0.15 0.40 1.14 70 245 22.5 0.29 1155

10 280 HB 0.5 4.0 0.15 0.40 1.14 70 195 22.5 0.29 1130

11 320 HB 0.5 3.0 0.15 0.35 0.76 70 170 22.2 0.27 1110

11 350 HB 0.5 3.0 0.15 0.35 0.76 70 145 22.2 0.27 1100

15 150 HB 0.5 5.0 0.13 0.60 1.90 170 325 33.0 0.33 2220

15 200 HB 0.5 5.0 0.13 0.60 1.71 160 300 33.0 0.33 2200

16 250 HB 0.5 5.0 0.13 0.55 1.71 150 275 33.0 0.33 1175

17,19 150 HB 0.5 5.0 0.13 0.50 1.43 120 325 33.0 0.29 2200

17,19 200 HB 0.5 5.0 0.13 0.50 1.24 120 300 33.0 0.29 1175

18,20 250 HB 0.5 5.0 0.13 0.50 1.14 120 245 33.0 0.29 1155

38 45 HRc 0.5 2.5 0.09 0.30 0.57 50 130 22.0 0.24 990

38 50 HRc 0.5 2.0 0.09 0.25 0.38 40 115 11.5 0.19 775

38 55 HRc 0.5 1.5 0.09 0.20 0.29 40 105 11.0 0.17 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

110



1 125 HB 0.7 5.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 5.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 5.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 5.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 4.0 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 4.0 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 3.5 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 4.0 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 4.0 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 3.0 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 3.0 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 5.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 5.0 0.25 0.54 1.70 160 220 44.0 0.36 1170

14 290 HB 0.7 4.0 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 4.0 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 5.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 4.0 0.28 0.54 1.70 120 190 33.0 0.35 1130

15 150 HB 0.7 5.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 5.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 5.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 5.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 5.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 5.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 3.0 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 3.0 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 3.0 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 4.0 0.25 0.54 1.36 45 65 22.7 0.40 555

37 T40 - 0.7 3.0 0.25 0.47 1.19 35 55 22.7 0.37 445

38 45 HRc 0.7 2.5 0.14 0.41 1.02 50 100 22.2 0.33 880

38 50 HRc 0.7 2.0 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 1.5 0.14 0.27 0.51 40 80 11.3 0.24 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 6.0 0.25 0.81 3.10 200 400 4.0 0.50 280

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

TNMG 160412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






111


TNMG 160412 NN – LT 1025


1 125 HB 0.7 5.0 0.26 0.68 3.06 90 330 33.6 0.50 2240

2 190 HB 0.7 5.0 0.26 0.68 3.06 90 280 33.6 0.46 2220

3 250 HB 0.7 5.0 0.26 0.61 2.55 90 250 33.6 0.44 2200

6 180 HB 0.7 5.0 0.26 0.61 2.04 60 280 33.6 0.42 2200

4,6 230 HB 0.7 4.0 0.26 0.61 2.04 60 250 33.6 0.42 1180

5,7 280 HB 0.7 4.0 0.23 0.54 2.04 60 210 33.6 0.40 1150

8 350 HB 0.7 3.5 0.23 0.54 1.70 60 180 33.2 0.40 1130

10 220 HB 0.7 4.0 0.23 0.54 2.04 35 190 33.0 0.40 1140

10 280 HB 0.7 4.0 0.23 0.54 2.04 35 150 33.0 0.40 1120

11 320 HB 0.7 3.0 0.23 0.47 1.36 35 130 22.6 0.37 1100

11 350 HB 0.7 3.0 0.23 0.47 1.36 35 110 22.6 0.37 990

14 180 HB 0.7 5.0 0.25 0.54 2.04 85 270 33.6 0.33 1190

14 240 HB 0.7 5.0 0.25 0.54 1.70 80 220 33.6 0.29 1170

14 290 HB 0.7 4.0 0.23 0.47 1.36 40 150 33.0 0.32 1100

14 310 HB 0.7 4.0 0.23 0.47 1.36 35 140 33.0 0.32 990

12 200 HB 0.7 5.0 0.23 0.54 1.19 85 250 33.0 0.26 1190

13 42 HRc 0.7 4.0 0.23 0.54 1.19 60 190 22.6 0.26 1130

17,19 150 HB 0.7 5.0 0.19 0.68 2.55 60 250 33.6 0.40 1180

17,19 200 HB 0.7 5.0 0.19 0.68 2.21 60 230 33.6 0.40 1160

18,20 250 HB 0.7 5.0 0.19 0.68 2.04 60 190 33.6 0.40 1140

Amax [mm²]

GGG40, GGG70, 50005

X2CrNiN23-4, S31500


Cast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



TNMG 160412 NN – LT 1005


1 125 HB 0.7 5.0 0.26 0.68 3.06 180 430 33.6 0.50 2265

2 190 HB 0.7 5.0 0.26 0.68 3.06 180 365 33.6 0.46 2240

3 250 HB 0.7 5.0 0.26 0.61 2.55 180 325 33.6 0.44 2220

6 180 HB 0.7 5.0 0.26 0.61 2.04 120 365 33.6 0.42 2220

4,6 230 HB 0.7 4.0 0.26 0.61 2.04 120 325 33.6 0.42 2200

5,7 280 HB 0.7 4.0 0.23 0.54 2.04 120 275 33.6 0.40 1165

8 350 HB 0.7 3.5 0.23 0.54 1.70 120 235 33.2 0.40 1145

10 220 HB 0.7 4.0 0.23 0.54 2.04 70 245 33.0 0.40 1155

10 280 HB 0.7 4.0 0.23 0.54 2.04 70 195 33.0 0.40 1130

11 320 HB 0.7 3.0 0.23 0.47 1.36 70 170 22.6 0.37 1110

11 350 HB 0.7 3.0 0.23 0.47 1.36 70 145 22.6 0.37 1100

15 150 HB 0.7 5.0 0.19 0.81 3.40 170 325 33.6 0.46 2220

15 200 HB 0.7 5.0 0.19 0.81 3.06 160 300 33.6 0.46 2200

16 250 HB 0.7 5.0 0.19 0.74 3.06 150 275 33.6 0.46 1175

17,19 150 HB 0.7 5.0 0.19 0.68 2.55 120 325 33.6 0.40 2200

17,19 200 HB 0.7 5.0 0.19 0.68 2.21 120 300 33.6 0.40 1175

18,20 250 HB 0.7 5.0 0.19 0.68 2.04 120 245 33.6 0.40 1155

38 45 HRc 0.7 2.5 0.14 0.41 1.02 50 130 22.4 0.33 990

38 50 HRc 0.7 2.0 0.14 0.34 0.68 40 115 11.8 0.26 775

38 55 HRc 0.7 1.5 0.14 0.27 0.51 40 105 11.2 0.24 665



X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



Low alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

112



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



TNMG 220404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






113



1 125 HB 0.5 7.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 7.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 7.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 7.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 5.6 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 5.6 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 4.9 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 5.6 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 5.6 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 4.2 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 4.2 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 7.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 7.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 5.6 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 5.6 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 7.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 5.6 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 7.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 7.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 7.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 7.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 7.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 4.2 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 4.2 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 4.2 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 5.6 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 4.2 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 3.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.8 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 2.1 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.4 0.20 0.60 1.80 200 400 3.0 0.40 280

St

eel

Non-alloyed

Low alloyed



1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

TNMG 220408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






114


TNMG 220408 NN – LT 1025


1 125 HB 0.5 7.0 0.21 0.50 1.80 90 330 33.0 0.38 2240

2 190 HB 0.5 7.0 0.21 0.50 1.80 90 280 33.0 0.35 2220

3 250 HB 0.5 7.0 0.21 0.45 1.50 90 250 33.0 0.33 2200

6 180 HB 0.5 7.0 0.21 0.45 1.20 60 280 33.0 0.32 2200

4,6 230 HB 0.5 5.6 0.21 0.45 1.20 60 250 33.0 0.32 1180

5,7 280 HB 0.5 5.6 0.18 0.40 1.20 60 210 33.0 0.30 1150

8 350 HB 0.5 4.9 0.18 0.40 1.00 60 180 22.7 0.30 1130

10 220 HB 0.5 5.6 0.18 0.40 1.20 35 190 22.5 0.30 1140

10 280 HB 0.5 5.6 0.18 0.40 1.20 35 150 22.5 0.30 1120

11 320 HB 0.5 4.2 0.18 0.35 0.80 35 130 22.2 0.28 1100

11 350 HB 0.5 4.2 0.18 0.35 0.80 35 110 22.2 0.28 990

14 180 HB 0.5 7.0 0.20 0.40 1.20 85 270 33.0 0.25 1190

14 240 HB 0.5 7.0 0.20 0.40 1.00 80 220 33.0 0.22 1170

14 290 HB 0.5 5.6 0.18 0.35 0.80 40 150 22.5 0.24 1100

14 310 HB 0.5 5.6 0.18 0.35 0.80 35 140 22.5 0.24 990

12 200 HB 0.5 7.0 0.18 0.40 0.70 85 250 22.5 0.20 1190

13 42 HRc 0.5 5.6 0.18 0.40 0.70 60 190 22.2 0.20 1130

17,19 150 HB 0.5 7.0 0.15 0.50 1.50 60 250 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.50 1.30 60 230 33.0 0.30 1160

18,20 250 HB 0.5 7.0 0.15 0.50 1.20 60 190 33.0 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

TNMG 220408 NN – LT 1005


1 125 HB 0.5 7.0 0.21 0.50 1.80 180 430 33.0 0.38 2265

2 190 HB 0.5 7.0 0.21 0.50 1.80 180 365 33.0 0.35 2240

3 250 HB 0.5 7.0 0.21 0.45 1.50 180 325 33.0 0.33 2220

6 180 HB 0.5 7.0 0.21 0.45 1.20 120 365 33.0 0.32 2220

4,6 230 HB 0.5 5.6 0.21 0.45 1.20 120 325 33.0 0.32 2200

5,7 280 HB 0.5 5.6 0.18 0.40 1.20 120 275 33.0 0.30 1165

8 350 HB 0.5 4.9 0.18 0.40 1.00 120 235 22.7 0.30 1145

10 220 HB 0.5 5.6 0.18 0.40 1.20 70 245 22.5 0.30 1155

10 280 HB 0.5 5.6 0.18 0.40 1.20 70 195 22.5 0.30 1130

11 320 HB 0.5 4.2 0.18 0.35 0.80 70 170 22.2 0.28 1110

11 350 HB 0.5 4.2 0.18 0.35 0.80 70 145 22.2 0.28 1100

15 150 HB 0.5 7.0 0.15 0.60 2.00 170 325 33.0 0.35 2220

15 200 HB 0.5 7.0 0.15 0.60 1.80 160 300 33.0 0.35 2200

16 250 HB 0.5 7.0 0.15 0.55 1.80 150 275 33.0 0.35 1175

17,19 150 HB 0.5 7.0 0.15 0.50 1.50 120 325 33.0 0.30 2200

17,19 200 HB 0.5 7.0 0.15 0.50 1.30 120 300 33.0 0.30 1175

18,20 250 HB 0.5 7.0 0.15 0.50 1.20 120 245 33.0 0.30 1155

38 45 HRc 0.5 3.5 0.11 0.30 0.60 50 130 22.0 0.25 990

38 50 HRc 0.5 2.8 0.11 0.25 0.40 40 115 11.5 0.20 775

38 55 HRc 0.5 2.1 0.11 0.20 0.30 40 105 11.0 0.18 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

115



1 125 HB 0.5 7.0 0.18 0.50 1.70 180 330 33.0 0.33 2240

2 190 HB 0.5 7.0 0.18 0.50 1.70 180 280 33.0 0.33 2220

3 250 HB 0.5 7.0 0.18 0.45 1.45 180 250 33.0 0.33 2200

6 180 HB 0.5 7.0 0.18 0.45 1.15 120 280 33.0 0.30 2200

4,6 230 HB 0.5 5.6 0.18 0.45 1.15 120 250 33.0 0.30 1180

5,7 280 HB 0.5 5.6 0.16 0.40 1.15 120 210 33.0 0.29 1150

8 350 HB 0.5 4.9 0.16 0.40 0.95 120 180 33.0 0.29 1130

10 220 HB 0.5 5.6 0.16 0.40 1.15 70 190 22.5 0.29 1140

10 280 HB 0.5 5.6 0.16 0.40 1.15 70 150 22.5 0.29 1120

11 320 HB 0.5 4.2 0.16 0.35 0.75 70 130 22.5 0.27 1100

11 350 HB 0.5 4.2 0.16 0.35 0.75 70 110 22.5 0.27 990

14 180 HB 0.5 7.0 0.18 0.40 1.15 170 270 33.0 0.24 1190

14 240 HB 0.5 7.0 0.18 0.40 0.95 160 220 33.0 0.21 1170

14 290 HB 0.5 5.6 0.16 0.35 0.75 80 150 22.5 0.27 1100

14 310 HB 0.5 5.6 0.16 0.35 0.75 70 140 22.5 0.27 990

12 200 HB 0.5 7.0 0.19 0.40 0.95 170 250 22.5 0.29 1190

13 42 HRc 0.5 5.6 0.19 0.40 0.95 120 190 22.5 0.24 1130

15 150 HB 0.5 7.0 0.13 0.60 1.90 170 250 33.0 0.33 2200

15 200 HB 0.5 7.0 0.13 0.60 1.70 160 230 33.0 0.33 1180

16 250 HB 0.5 7.0 0.13 0.55 1.70 150 210 33.0 0.33 1160

17,19 150 HB 0.5 7.0 0.13 0.50 1.45 120 250 33.0 0.29 1180

17,19 200 HB 0.5 7.0 0.13 0.50 1.25 120 230 33.0 0.29 1160

18,20 250 HB 0.5 7.0 0.13 0.50 1.15 120 190 33.0 0.29 1140

31,32 Incoloy 800 240 HB 0.5 4.2 0.18 0.35 0.65 25 45 22.0 0.27 330

33 Inconel 700 250 HB 0.5 4.2 0.18 0.35 0.65 25 45 22.0 0.27 330

34 Stellite 21 350 HB 0.5 4.2 0.18 0.35 0.65 25 40 22.0 0.27 330

36 TiAl6V4 - 0.5 5.6 0.18 0.40 0.75 45 65 22.0 0.31 555

37 T40 - 0.5 4.2 0.18 0.35 0.65 35 55 22.0 0.29 445

38 45 HRc 0.5 3.5 0.10 0.30 0.55 50 100 22.0 0.24 880

38 50 HRc 0.5 2.8 0.10 0.25 0.40 40 90 11.5 0.19 770

38 55 HRc 0.5 2.1 0.10 0.20 0.30 40 80 11.0 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.4 0.18 0.60 1.70 200 400 33.0 0.38 280

St

eel

Non-alloyed

Low alloyed

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


2

1C35, Ck45, 1020, 1045, 1060, 28Mn6


X100CrMo13, 440C,

G-X260NiCr42

304, 316, X5CrNi18-9

GGG40, GGG70, 50005

GG20, GG40, EN-GJL-250,

No30B

10

8

X2CrNiN23-4, S31500

Hard

ened

Mat

.

Steel

11

Stai

nles

s St

eel

Austenitic 4

Duplex 5

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron

Grey 7

Malleable & Nodular

TNMG 220408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






116


TNMG 220408 NX – LT 1025


1 125 HB 0.5 7.0 0.18 0.50 1.71 90 330 33.0 0.36 2240

2 190 HB 0.5 7.0 0.18 0.50 1.71 90 280 33.0 0.33 2220

3 250 HB 0.5 7.0 0.18 0.45 1.43 90 250 33.0 0.31 2200

6 180 HB 0.5 7.0 0.18 0.45 1.14 60 280 33.0 0.30 2200

4,6 230 HB 0.5 5.6 0.18 0.45 1.14 60 250 33.0 0.30 1180

5,7 280 HB 0.5 5.6 0.16 0.40 1.14 60 210 33.0 0.29 1150

8 350 HB 0.5 4.9 0.16 0.40 0.95 60 180 22.7 0.29 1130

10 220 HB 0.5 5.6 0.16 0.40 1.14 35 190 22.5 0.29 1140

10 280 HB 0.5 5.6 0.16 0.40 1.14 35 150 22.5 0.29 1120

11 320 HB 0.5 4.2 0.16 0.35 0.76 35 130 22.2 0.27 1100

11 350 HB 0.5 4.2 0.16 0.35 0.76 35 110 22.2 0.27 990

14 180 HB 0.5 7.0 0.18 0.40 1.14 85 270 33.0 0.24 1190

14 240 HB 0.5 7.0 0.18 0.40 0.95 80 220 33.0 0.21 1170

14 290 HB 0.5 5.6 0.16 0.35 0.76 40 150 22.5 0.23 1100

14 310 HB 0.5 5.6 0.16 0.35 0.76 35 140 22.5 0.23 990

12 200 HB 0.5 7.0 0.16 0.40 0.67 85 250 22.5 0.19 1190

13 42 HRc 0.5 5.6 0.16 0.40 0.67 60 190 22.2 0.19 1130

17,19 150 HB 0.5 7.0 0.13 0.50 1.43 60 250 33.0 0.29 1180

17,19 200 HB 0.5 7.0 0.13 0.50 1.24 60 230 33.0 0.29 1160

18,20 250 HB 0.5 7.0 0.13 0.50 1.14 60 190 33.0 0.29 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

TNMG 220408 NX – LT 1005


1 125 HB 0.5 7.0 0.18 0.50 1.71 180 430 33.0 0.36 2265

2 190 HB 0.5 7.0 0.18 0.50 1.71 180 365 33.0 0.33 2240

3 250 HB 0.5 7.0 0.18 0.45 1.43 180 325 33.0 0.31 2220

6 180 HB 0.5 7.0 0.18 0.45 1.14 120 365 33.0 0.30 2220

4,6 230 HB 0.5 5.6 0.18 0.45 1.14 120 325 33.0 0.30 2200

5,7 280 HB 0.5 5.6 0.16 0.40 1.14 120 275 33.0 0.29 1165

8 350 HB 0.5 4.9 0.16 0.40 0.95 120 235 22.7 0.29 1145

10 220 HB 0.5 5.6 0.16 0.40 1.14 70 245 22.5 0.29 1155

10 280 HB 0.5 5.6 0.16 0.40 1.14 70 195 22.5 0.29 1130

11 320 HB 0.5 4.2 0.16 0.35 0.76 70 170 22.2 0.27 1110

11 350 HB 0.5 4.2 0.16 0.35 0.76 70 145 22.2 0.27 1100

15 150 HB 0.5 7.0 0.13 0.60 1.90 170 325 33.0 0.33 2220

15 200 HB 0.5 7.0 0.13 0.60 1.71 160 300 33.0 0.33 2200

16 250 HB 0.5 7.0 0.13 0.55 1.71 150 275 33.0 0.33 1175

17,19 150 HB 0.5 7.0 0.13 0.50 1.43 120 325 33.0 0.29 2200

17,19 200 HB 0.5 7.0 0.13 0.50 1.24 120 300 33.0 0.29 1175

18,20 250 HB 0.5 7.0 0.13 0.50 1.14 120 245 33.0 0.29 1155

38 45 HRc 0.5 3.5 0.10 0.30 0.57 50 130 22.0 0.24 990

38 50 HRc 0.5 2.8 0.10 0.25 0.38 40 115 11.5 0.19 775

38 55 HRc 0.5 2.1 0.10 0.20 0.29 40 105 11.0 0.17 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

117



1 125 HB 0.7 7.0 0.26 0.68 3.06 180 330 44.0 0.46 2240

2 190 HB 0.7 7.0 0.26 0.68 3.06 180 280 44.0 0.46 2220

3 250 HB 0.7 7.0 0.26 0.61 2.55 180 250 44.0 0.46 2200

6 180 HB 0.7 7.0 0.26 0.61 2.04 120 280 44.0 0.42 2200

4,6 230 HB 0.7 5.6 0.26 0.61 2.04 120 250 44.0 0.42 1180

5,7 280 HB 0.7 5.6 0.23 0.54 2.04 120 210 44.0 0.40 1150

8 350 HB 0.7 4.9 0.23 0.54 1.70 120 180 44.0 0.40 1130

10 220 HB 0.7 5.6 0.23 0.54 2.04 70 190 33.4 0.40 1140

10 280 HB 0.7 5.6 0.23 0.54 2.04 70 150 33.4 0.40 1120

11 320 HB 0.7 4.2 0.23 0.47 1.36 70 130 33.4 0.37 1100

11 350 HB 0.7 4.2 0.23 0.47 1.36 70 110 33.4 0.37 990

14 180 HB 0.7 7.0 0.25 0.54 2.04 170 270 44.0 0.40 1190

14 240 HB 0.7 7.0 0.25 0.54 1.70 160 220 44.0 0.36 1170

14 290 HB 0.7 5.6 0.23 0.47 1.36 80 150 33.4 0.32 1100

14 310 HB 0.7 5.6 0.23 0.47 1.36 70 140 33.4 0.32 990

12 200 HB 0.7 7.0 0.28 0.54 1.70 170 250 44.0 0.40 1190

13 42 HRc 0.7 5.6 0.28 0.54 1.70 120 190 33.0 0.35 1130

15 150 HB 0.7 7.0 0.20 0.81 3.40 170 250 44.0 0.46 2200

15 200 HB 0.7 7.0 0.20 0.81 3.06 160 230 44.0 0.46 1180

16 250 HB 0.7 7.0 0.20 0.74 3.06 150 210 44.0 0.46 1160

17,19 150 HB 0.7 7.0 0.20 0.68 2.55 120 250 44.0 0.40 1180

17,19 200 HB 0.7 7.0 0.20 0.68 2.21 120 230 44.0 0.40 1160

18,20 250 HB 0.7 7.0 0.20 0.68 2.04 120 190 44.0 0.40 1140

31,32 Incoloy 800 240 HB 0.7 4.2 0.25 0.47 1.19 25 45 22.7 0.37 332

33 Inconel 700 250 HB 0.7 4.2 0.25 0.47 1.19 25 45 22.7 0.37 330

34 Stellite 21 350 HB 0.7 4.2 0.25 0.47 1.19 23 40 22.7 0.37 228

36 TiAl6V4 - 0.7 5.6 0.25 0.54 1.36 45 65 22.7 0.40 555

37 T40 - 0.7 4.2 0.25 0.47 1.19 35 55 22.7 0.37 445

38 45 HRc 0.7 3.5 0.14 0.41 1.02 50 100 22.2 0.33 880

38 50 HRc 0.7 2.8 0.14 0.34 0.68 40 90 22.0 0.26 770

38 55 HRc 0.7 2.1 0.14 0.27 0.51 40 80 11.3 0.24 660Chilled Cast

IIron40 Ni-Hard 2 400 HB 0.7 2.8 0.14 0.34 0.68 40 60 22.0 0.24 550


NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 7.0 0.25 0.81 3.10 200 400 44.0 0.50 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


6 410, X6Cr17, 17-4 PH, 430

Cast

Iron


No30B

Malleable & Nodular

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

TNMG 220412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






118


TNMG 220412 NN – LT 1025


1 125 HB 0.7 7.0 0.26 0.68 3.06 90 330 44.0 00.50 2240

2 190 HB 0.7 7.0 0.26 0.68 3.06 90 280 44.0 00.46 2220

3 250 HB 0.7 7.0 0.26 0.61 2.55 90 250 44.0 00.44 2200

6 180 HB 0.7 7.0 0.26 0.61 2.04 60 280 44.0 00.42 2200

4,6 230 HB 0.7 5.6 0.26 0.61 2.04 60 250 44.0 00.42 1180

5,7 280 HB 0.7 5.6 0.23 0.54 2.04 60 210 44.0 00.40 1150

8 350 HB 0.7 4.9 0.23 0.54 1.70 60 180 33.6 00.40 1130

10 220 HB 0.7 5.6 0.23 0.54 2.04 35 190 33.4 00.40 1140

10 280 HB 0.7 5.6 0.23 0.54 2.04 35 150 33.4 00.40 1120

11 320 HB 0.7 4.2 0.23 0.47 1.36 35 130 22.9 00.37 1100

11 350 HB 0.7 4.2 0.23 0.47 1.36 35 110 22.9 00.37 990

14 180 HB 0.7 7.0 0.25 0.54 2.04 85 270 44.0 00.33 1190

14 240 HB 0.7 7.0 0.25 0.54 1.70 80 220 44.0 00.29 1170

14 290 HB 0.7 5.6 0.23 0.47 1.36 40 150 33.4 00.32 1100

14 310 HB 0.7 5.6 0.23 0.47 1.36 35 140 33.4 00.32 990

12 200 HB 0.7 7.0 0.23 0.54 1.19 85 250 33.4 00.26 1190

13 42 HRc 0.7 5.6 0.23 0.54 1.19 60 190 22.9 00.26 1130

17,19 150 HB 0.7 7.0 0.19 0.68 2.55 60 250 44.0 00.40 1180

17,19 200 HB 0.7 7.0 0.19 0.68 2.21 60 230 44.0 00.40 1160

18,20 250 HB 0.7 7.0 0.19 0.68 2.04 60 190 44.0 00.40 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

TNMG 220412 NN – LT 1005


1 125 HB 0.7 7.0 0.26 0.68 3.06 180 430 44.0 00.50 2265

2 190 HB 0.7 7.0 0.26 0.68 3.06 180 365 44.0 00.46 2240

3 250 HB 0.7 7.0 0.26 0.61 2.55 180 325 44.0 00.44 2220

6 180 HB 0.7 7.0 0.26 0.61 2.04 120 365 44.0 00.42 2220

4,6 230 HB 0.7 5.6 0.26 0.61 2.04 120 325 44.0 00.42 2200

5,7 280 HB 0.7 5.6 0.23 0.54 2.04 120 275 44.0 00.40 1165

8 350 HB 0.7 4.9 0.23 0.54 1.70 120 235 33.6 00.40 1145

10 220 HB 0.7 5.6 0.23 0.54 2.04 70 245 33.4 00.40 1155

10 280 HB 0.7 5.6 0.23 0.54 2.04 70 195 33.4 00.40 1130

11 320 HB 0.7 4.2 0.23 0.47 1.36 70 170 22.9 00.37 1110

11 350 HB 0.7 4.2 0.23 0.47 1.36 70 145 22.9 00.37 1100

15 150 HB 0.7 7.0 0.19 0.81 3.40 170 325 44.0 00.46 2220

15 200 HB 0.7 7.0 0.19 0.81 3.06 160 300 44.0 00.46 2200

16 250 HB 0.7 7.0 0.19 0.74 3.06 150 275 44.0 00.46 1175

17,19 150 HB 0.7 7.0 0.19 0.68 2.55 120 325 44.0 00.40 2200

17,19 200 HB 0.7 7.0 0.19 0.68 2.21 120 300 44.0 00.40 1175

18,20 250 HB 0.7 7.0 0.19 0.68 2.04 120 245 44.0 00.40 1155

38 45 HRc 0.7 3.5 0.14 0.41 1.02 50 130 22.7 00.33 990

38 50 HRc 0.7 2.8 0.14 0.34 0.68 40 115 22.0 00.26 775

38 55 HRc 0.7 2.1 0.14 0.27 0.51 40 105 11.3 00.24 665



X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



Low alloyed 2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


119

TURNING

NXCNMPTNMPWNMP

Exotic Material


T N M P

Shape Toleranced ± 0.05m ± 0.08s ± 0.13

0°

Clearance Anglel

m

Ø d60°

Fixing,Chipbreaker

ss

F M R

Application Guide


T00041450.804.7616TNMP 160408 NN LT 1025


60° triangle shape inserts with positive chip breaker geometry. Generates low cutting forces. Suitable for general purpose, copying, high temperature alloys and stainless steel turning operations.

TNMP

120


TNMP 160408 NN – LT 1025


1 125 HB 0.5 5.0 0.21 0.50 1.80 90 330 33.0 00.38 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 90 280 33.0 00.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 90 250 33.0 00.33 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 60 280 33.0 00.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 60 250 33.0 00.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 60 210 33.0 00.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 60 180 22.7 00.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 35 190 22.5 00.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 35 150 22.5 00.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 35 130 22.2 00.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 35 110 22.2 00.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 85 270 33.0 00.25 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 80 220 33.0 00.22 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 40 150 22.5 00.24 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 35 140 22.5 00.24 990

12 200 HB 0.5 5.0 0.18 0.40 0.70 85 250 22.5 00.20 1190

13 42 HRc 0.5 4.0 0.18 0.40 0.70 60 190 22.2 00.20 1130

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 60 250 33.0 00.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 60 230 33.0 00.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 60 190 33.0 00.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

FFerritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430

CCast

Iron


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

HHigh alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

SStai

nles

s St

eel

AAustenitic 4304, 316,

X5CrNi18-9

DDuplex 5

St

eel

NNon-alloyed 1C35, Ck45, 1020, 1045, 1060, 28Mn6

LLow alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


121

TURNING

FProductivity

Stainless Steel

VC

T N U X


0°


l

m

Ø d60°

s

F M R

Application Guide



T00033850.804.7616TNUX 160408 L LT10

T00011370.804.7616TNUX 160408 R LT 10

T00018770.404.7616TNUX 160404 L LT 10

T00011250.404.7616TNUX 160404 R LT 10

F M R

Application Guide


T00027950.804.7616TNUX 160408 L LT 1000

T00019390.804.7616TNUX 160408 R LT 1000

T00027940.404.7616TNUX 160404 L LT 1000

T00019380.404.7616TNUX 160404 R LT 1000


Sh

60° triangle shape inserts. Suitable for general turning and longitudinal operations, where there is a con-cern for work piece vibrations.

Left

TNUX

122

TURNING


1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

TNUX 160404 L/R – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






123



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 33.0 0.40 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



St

eel

Non-alloyed

Low alloyed


TNUX 160408 L/R – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






124

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


FProductivity

Stainless Steel

VC

T P M R


Clearance Angle

11°

Fixing,Chipbreaker

l

m

Ø d60°

s

F M R

Application Guide



T00015350.803.7616TPMR 160308 NN LT 10

T00016380.403.7616TPMR 160304 NN LT 10

60° triangle shape inserts with positive rake angle. Suitable for boring and internal turing operations.

125



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

TPMR 160304 NN – LT 10

TPMR

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






126



1 125 HB 0.5 5.0 0.21 0.50 1.80 180 330 33.0 0.35 2240

2 190 HB 0.5 5.0 0.21 0.50 1.80 180 280 33.0 0.35 2220

3 250 HB 0.5 5.0 0.21 0.45 1.50 180 250 33.0 0.35 2200

6 180 HB 0.5 5.0 0.21 0.45 1.20 120 280 33.0 0.32 2200

4,6 230 HB 0.5 4.0 0.21 0.45 1.20 120 250 33.0 0.32 1180

5,7 280 HB 0.5 4.0 0.18 0.40 1.20 120 210 33.0 0.30 1150

8 350 HB 0.5 3.5 0.18 0.40 1.00 120 180 33.0 0.30 1130

10 220 HB 0.5 4.0 0.18 0.40 1.20 70 190 22.5 0.30 1140

10 280 HB 0.5 4.0 0.18 0.40 1.20 70 150 22.5 0.30 1120

11 320 HB 0.5 3.0 0.18 0.35 0.80 70 130 22.5 0.28 1100

11 350 HB 0.5 3.0 0.18 0.35 0.80 70 110 22.5 0.28 990

14 180 HB 0.5 5.0 0.20 0.40 1.20 170 270 33.0 0.35 1190

14 240 HB 0.5 5.0 0.20 0.40 1.00 160 220 33.0 0.32 1170

14 290 HB 0.5 4.0 0.18 0.35 0.80 80 150 22.5 0.28 1100

14 310 HB 0.5 4.0 0.18 0.35 0.80 70 140 22.5 0.28 990

12 200 HB 0.5 5.0 0.22 0.40 1.00 170 250 33.0 0.32 1190

13 42 HRc 0.5 4.0 0.22 0.40 1.00 120 190 22.5 0.32 1130

15 150 HB 0.5 5.0 0.15 0.60 2.00 170 250 33.0 0.35 2200

15 200 HB 0.5 5.0 0.15 0.60 1.80 160 230 33.0 0.35 1180

16 250 HB 0.5 5.0 0.15 0.55 1.80 150 210 33.0 0.35 1160

17,19 150 HB 0.5 5.0 0.15 0.50 1.50 120 250 33.0 0.30 1180

17,19 200 HB 0.5 5.0 0.15 0.50 1.30 120 230 33.0 0.30 1160

18,20 250 HB 0.5 5.0 0.15 0.50 1.20 120 190 33.0 0.30 1140

31,32 Incoloy 800 240 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 332

33 Inconel 700 250 HB 0.5 3.0 0.20 0.35 0.70 25 45 22.0 0.28 330

34 Stellite 21 350 HB 0.5 3.0 0.20 0.35 0.70 23 40 22.0 0.28 228

36 TiAl6V4 - 0.5 4.0 0.20 0.40 0.80 45 65 22.0 0.33 555

37 T40 - 0.5 3.0 0.20 0.35 0.70 35 55 22.0 0.30 445

38 45 HRc 0.5 2.5 0.11 0.30 0.60 50 100 22.0 0.25 880

38 50 HRc 0.5 2.0 0.11 0.25 0.40 40 90 11.5 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.0 0.20 0.60 1.80 200 400 3.0 0.40 280

St

eel

Non-alloyed

Low alloyed

1C35, Ck45, 1020,

1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

TPMR 160308 NN – LT 10

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


127

TURNING

FProductivity

Stainless Steel

VC

V B M T


Clearance Angle

5°

Fixing,Chipbreaker

35° Ø d

l

m

s

F M R

Application Guide



T00000710.804.7616VBMT 160408 NN LT 10

T00000700.404.7616VBMT 160404 NN LT 10

T00014600.403.7611VBMT 110304 NN LT 10

F M R

Application Guide


T00019440.804.7616VBMT 160408 NN LT 1000

T00019430.404.7616VBMT 160404 NN LT 1000

T00019420.403.7611VBMT 110304 NN LT 1000


35° diamond shape inserts with positive rake angle. Suitable for internal and external copying operations of complex geometries.

VBMT

128



1 125 HB 0.3 2.1 0.08 0.20 0.37 180 330 11.0 0.14 3300

2 190 HB 0.3 1.8 0.08 0.19 0.32 180 280 11.0 0.14 2260

3 250 HB 0.3 1.8 0.08 0.17 0.30 180 250 11.0 0.14 2240

6 180 HB 0.3 1.8 0.08 0.17 0.31 120 280 11.0 0.11 2260

4,6 230 HB 0.3 1.8 0.08 0.17 0.30 120 250 11.0 0.11 2240

5,7 280 HB 0.3 1.4 0.08 0.15 0.25 120 210 11.0 0.10 2200

8 350 HB 0.3 1.4 0.08 0.15 0.22 120 180 11.0 0.10 1180

10 220 HB 0.3 1.8 0.07 0.15 0.25 70 190 00.9 0.08 1180

10 280 HB 0.3 1.8 0.07 0.14 0.25 70 150 00.9 0.08 1140

11 320 HB 0.3 1.4 0.07 0.12 0.20 70 130 00.9 0.08 1120

11 350 HB 0.3 1.4 0.07 0.12 0.16 70 110 00.9 0.08 1110

14 180 HB 0.3 1.8 0.06 0.15 0.20 170 270 11.0 0.07 2260

14 240 HB 0.3 1.8 0.06 0.15 0.16 160 220 11.0 0.06 2210

14 290 HB 0.3 1.4 0.06 0.12 0.12 80 150 00.9 0.06 1140

14 310 HB 0.3 1.4 0.06 0.12 0.12 70 140 00.9 0.06 1140

12 200 HB 0.3 1.8 0.06 0.15 0.20 170 250 00.9 0.07 2240

13 42 HRc 0.3 1.4 0.06 0.14 0.16 120 190 00.8 0.06 1180

15 150 HB 0.3 2.1 0.06 0.17 0.40 170 250 11.0 0.14 2240

15 200 HB 0.3 2.1 0.06 0.17 0.37 160 230 11.0 0.14 2220

16 250 HB 0.3 2.1 0.06 0.17 0.37 150 210 11.0 0.14 2200

17,19 150 HB 0.3 1.8 0.06 0.15 0.30 120 250 11.0 0.10 2240

17,19 200 HB 0.3 1.8 0.06 0.15 0.25 120 230 11.0 0.10 2220

18,20 250 HB 0.3 1.8 0.06 0.15 0.25 120 190 11.0 0.10 1180

31,32 Incoloy 800 240 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

33 Inconel 700 250 HB 0.3 1.4 0.07 0.13 0.16 25 50 00.7 0.08 440

34 Stellite 21 350 HB 0.3 1.4 0.07 0.13 0.16 23 45 00.7 0.08 335

36 TiAl6V4 - 0.3 1.4 0.07 0.14 0.20 45 65 00.7 0.11 660

37 T40 - 0.3 1.4 0.07 0.12 0.16 35 60 00.7 0.08 550

38 45 HRc 0.3 1.3 0.04 0.10 0.12 50 100 00.7 0.08 990

38 50 HRc 0.3 1.1 0.04 0.09 0.11 40 90 00.6 0.06 880

38 55 HRc 0.3 1.0 0.04 0.08 0.08 40 80 00.5 0.05 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.8 0.08 0.26 0.43 200 400 1.0 0.18 350

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

VBMT 110304 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






129



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

VBMT 160404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






130



1 125 HB 0.5 3.5 0.19 0.40 1.26 180 330 22.5 0.30 2240

2 190 HB 0.5 3.5 0.19 0.40 1.26 180 280 22.5 0.30 2220

3 250 HB 0.5 3.5 0.19 0.36 1.05 180 250 22.5 0.30 2200

6 180 HB 0.5 3.5 0.19 0.36 0.84 120 280 22.5 0.27 2200

4,6 230 HB 0.5 2.8 0.19 0.36 0.84 120 250 22.5 0.27 1180

5,7 280 HB 0.5 2.8 0.16 0.32 0.84 120 210 22.5 0.26 1150

8 350 HB 0.5 2.5 0.16 0.32 0.70 120 180 22.5 0.26 1130

10 220 HB 0.5 2.8 0.16 0.32 0.84 70 190 22.1 0.26 1140

10 280 HB 0.5 2.8 0.16 0.32 0.84 70 150 22.1 0.26 1120

11 320 HB 0.5 2.1 0.16 0.28 0.56 70 130 22.1 0.24 1100

11 350 HB 0.5 2.1 0.16 0.28 0.56 70 110 22.1 0.24 990

14 180 HB 0.5 3.5 0.18 0.32 0.84 170 270 22.5 0.30 1190

14 240 HB 0.5 3.5 0.18 0.32 0.70 160 220 22.5 0.27 1170

14 290 HB 0.5 2.8 0.16 0.28 0.56 80 150 22.1 0.24 1100

14 310 HB 0.5 2.8 0.16 0.28 0.56 70 140 22.1 0.24 990

12 200 HB 0.5 3.5 0.20 0.32 0.70 170 250 22.5 0.27 1190

13 42 HRc 0.5 2.8 0.20 0.32 0.70 120 190 22.5 0.27 1130

15 150 HB 0.5 3.5 0.14 0.48 1.40 170 250 22.5 0.30 2200

15 200 HB 0.5 3.5 0.14 0.48 1.26 160 230 22.5 0.30 1180

16 250 HB 0.5 3.5 0.14 0.44 1.26 150 210 22.5 0.30 1160

17,19 150 HB 0.5 3.5 0.14 0.40 1.05 120 250 22.5 0.26 1180

17,19 200 HB 0.5 3.5 0.14 0.40 0.91 120 230 22.5 0.26 1160

18,20 250 HB 0.5 3.5 0.14 0.40 0.84 120 190 22.5 0.26 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 332

33 Inconel 700 250 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 330

34 Stellite 21 350 HB 0.5 2.1 0.18 0.28 0.49 23 40 22.0 0.24 228

36 TiAl6V4 - 0.5 2.8 0.18 0.32 0.56 45 65 22.0 0.28 555

37 T40 - 0.5 2.1 0.18 0.28 0.49 35 55 22.0 0.26 445

38 45 HRc 0.5 1.8 0.10 0.24 0.42 50 100 11.6 0.21 880

38 50 HRc 0.5 1.4 0.10 0.20 0.28 40 90 11.2 0.17 770

38 55 HRc 0.5 1.1 0.10 0.16 0.21 40 80 11.0 0.15 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.48 1.40 200 400 22.5 0.34 280

St

eel

Non-alloyed

Low alloyed



1C35, Ck45, 1020, 1045, 1060, 28Mn6

Amax [mm²]



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500


Stai

nles

s St

eel


X5CrNi18-9

Duplex

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

VBMT 160408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


131

TURNING

FProductivity

Stainless Steel

VC

V C M T


Clearance Angle

7°

Fixing,Chipbreaker

35° Ø d

l

m

s

F M R

Application Guide



T00011030.804.7616VCMT 160408 NN LT 10

T00011020.404.7616VCMT 160404 NN LT 10

F M R

Application Guide


T00019460.804.7616VCMT 160408 NN LT 1000

T00019450.404.7616VCMT 160404 NN LT 1000


35° diamond shape inserts with positive rake angle. Suitable for internal and external copying operations of complex geometries.

VCMT

132



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

VCMT 160404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






133



1 125 HB 0.5 3.5 0.19 0.40 1.26 180 330 22.5 0.30 2240

2 190 HB 0.5 3.5 0.19 0.40 1.26 180 280 22.5 0.30 2220

3 250 HB 0.5 3.5 0.19 0.36 1.05 180 250 22.5 0.30 2200

6 180 HB 0.5 3.5 0.19 0.36 0.84 120 280 22.5 0.27 2200

4,6 230 HB 0.5 2.8 0.19 0.36 0.84 120 250 22.5 0.27 1180

5,7 280 HB 0.5 2.8 0.16 0.32 0.84 120 210 22.5 0.26 1150

8 350 HB 0.5 2.5 0.16 0.32 0.70 120 180 22.5 0.26 1130

10 220 HB 0.5 2.8 0.16 0.32 0.84 70 190 22.1 0.26 1140

10 280 HB 0.5 2.8 0.16 0.32 0.84 70 150 22.1 0.26 1120

11 320 HB 0.5 2.1 0.16 0.28 0.56 70 130 22.1 0.24 1100

11 350 HB 0.5 2.1 0.16 0.28 0.56 70 110 22.1 0.24 990

14 180 HB 0.5 3.5 0.18 0.32 0.84 170 270 22.5 0.30 1190

14 240 HB 0.5 3.5 0.18 0.32 0.70 160 220 22.5 0.27 1170

14 290 HB 0.5 2.8 0.16 0.28 0.56 80 150 22.1 0.24 1100

14 310 HB 0.5 2.8 0.16 0.28 0.56 70 140 22.1 0.24 990

12 200 HB 0.5 3.5 0.20 0.32 0.70 170 250 22.5 0.27 1190

13 42 HRc 0.5 2.8 0.20 0.32 0.70 120 190 22.5 0.27 1130

15 150 HB 0.5 3.5 0.14 0.48 1.40 170 250 22.5 0.30 2200

15 200 HB 0.5 3.5 0.14 0.48 1.26 160 230 22.5 0.30 1180

16 250 HB 0.5 3.5 0.14 0.44 1.26 150 210 22.5 0.30 1160

17,19 150 HB 0.5 3.5 0.14 0.40 1.05 120 250 22.5 0.26 1180

17,19 200 HB 0.5 3.5 0.14 0.40 0.91 120 230 22.5 0.26 1160

18,20 250 HB 0.5 3.5 0.14 0.40 0.84 120 190 22.5 0.26 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 332

33 Inconel 700 250 HB 0.5 2.1 0.18 0.28 0.49 25 45 22.0 0.24 330

34 Stellite 21 350 HB 0.5 2.1 0.18 0.28 0.49 23 40 22.0 0.24 228

36 TiAl6V4 - 0.5 2.8 0.18 0.32 0.56 45 65 22.0 0.28 555

37 T40 - 0.5 2.1 0.18 0.28 0.49 35 55 22.0 0.26 445

38 45 HRc 0.5 1.8 0.10 0.24 0.42 50 100 11.6 0.21 880

38 50 HRc 0.5 1.4 0.10 0.20 0.28 40 90 11.2 0.17 770

38 55 HRc 0.5 1.1 0.10 0.16 0.21 40 80 11.0 0.15 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.48 1.40 200 400 22.5 0.34 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

VCMT 160408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






134

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


V N M G


Clearance Angle

0°

Fixing,Chipbreaker

35° Ø d

l

m

ss

F M R

Application Guide



T00000730.804.7616VNMG 160408 NN LT 10

T00000720.404.7616VNMG 160404 NN LT 10

F M R

Application Guide


T00040950.804.7616VNMG 160408 NN LT 1005


F M R

Application Guide


T00041490.804.7616VNMG 160408 NN LT 1025


F M R

Application Guide

s r Catalog Nr.l

T00019480.804.7616VNMG 160408 NN LT 1000

T00019470.404.7616VNMG 160404 NN LT 1000

Insert Designation


35° diamond shape inserts. Suitable for external copying operations.

LT 1005

FProductivity

Stainless Steel

VC


VC

Productivity

135



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

VNMG 160404 NN – LT 10 | LT 1000

VNMG

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






136



1 125 HB 0.5 4.0 0.19 0.40 1.44 180 330 22.7 0.32 2240

2 190 HB 0.5 4.0 0.19 0.40 1.44 180 280 22.7 0.32 2220

3 250 HB 0.5 4.0 0.19 0.36 1.20 180 250 22.7 0.32 2200

6 180 HB 0.5 4.0 0.19 0.36 0.96 120 280 22.7 0.29 2200

4,6 230 HB 0.5 3.2 0.19 0.36 0.96 120 250 22.7 0.29 1180

5,7 280 HB 0.5 3.2 0.16 0.32 0.96 120 210 22.7 0.27 1150

8 350 HB 0.5 2.8 0.16 0.32 0.80 120 180 22.7 0.27 1130

10 220 HB 0.5 3.2 0.16 0.32 0.96 70 190 22.3 0.27 1140

10 280 HB 0.5 3.2 0.16 0.32 0.96 70 150 22.3 0.27 1120

11 320 HB 0.5 2.4 0.16 0.28 0.64 70 130 22.3 0.25 1100

11 350 HB 0.5 2.4 0.16 0.28 0.64 70 110 22.3 0.25 990

14 180 HB 0.5 4.0 0.18 0.32 0.96 170 270 22.7 0.32 1190

14 240 HB 0.5 4.0 0.18 0.32 0.80 160 220 22.7 0.29 1170

14 290 HB 0.5 3.2 0.16 0.28 0.64 80 150 22.3 0.25 1100

14 310 HB 0.5 3.2 0.16 0.28 0.64 70 140 22.3 0.25 990

12 200 HB 0.5 4.0 0.20 0.32 0.80 170 250 22.7 0.29 1190

13 42 HRc 0.5 3.2 0.20 0.32 0.80 120 190 22.5 0.29 1130

15 150 HB 0.5 4.0 0.14 0.48 1.60 170 250 22.7 0.32 2200

15 200 HB 0.5 4.0 0.14 0.48 1.44 160 230 22.7 0.32 1180

16 250 HB 0.5 4.0 0.14 0.44 1.44 150 210 22.7 0.32 1160

17,19 150 HB 0.5 4.0 0.14 0.40 1.20 120 250 22.7 0.27 1180

17,19 200 HB 0.5 4.0 0.14 0.40 1.04 120 230 22.7 0.27 1160

18,20 250 HB 0.5 4.0 0.14 0.40 0.96 120 190 22.7 0.27 1140

31,32 Incoloy 800 240 HB 0.5 2.4 0.18 0.28 0.56 25 45 22.0 0.25 332

33 Inconel 700 250 HB 0.5 2.4 0.18 0.28 0.56 25 45 22.0 0.25 330

34 Stellite 21 350 HB 0.5 2.4 0.18 0.28 0.56 23 40 22.0 0.25 228

36 TiAl6V4 - 0.5 3.2 0.18 0.32 0.64 45 65 22.0 0.30 555

37 T40 - 0.5 2.4 0.18 0.28 0.56 35 55 22.0 0.27 445

38 45 HRc 0.5 2.0 0.10 0.24 0.48 50 100 11.8 0.23 880

38 50 HRc 0.5 1.6 0.10 0.20 0.32 40 90 11.4 0.18 770

38 55 HRc 0.5 1.2 0.10 0.16 0.24 40 80 11.0 0.16 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.8 0.18 0.48 1.40 200 400 22.7 0.36 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8


Stai

nles

s St

eel


X5CrNi18-9

Duplex

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


5

2

X2CrNiN23-4, S31500

1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

VNMG 160408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






137


VNMG 160408 NN – LT 1025


1 125 HB 0.5 4.0 0.19 0.40 1.44 90 330 22.7 0.34 2240

2 190 HB 0.5 4.0 0.19 0.40 1.44 90 280 22.7 0.32 2220

3 250 HB 0.5 4.0 0.19 0.36 1.20 90 250 22.7 0.30 2200

6 180 HB 0.5 4.0 0.19 0.36 0.96 60 280 22.7 0.29 2200

4,6 230 HB 0.5 3.2 0.19 0.36 0.96 60 250 22.7 0.29 1180

5,7 280 HB 0.5 3.2 0.16 0.32 0.96 60 210 22.7 0.27 1150

8 350 HB 0.5 2.8 0.16 0.32 0.80 60 180 22.4 0.27 1130

10 220 HB 0.5 3.2 0.16 0.32 0.96 35 190 22.3 0.27 1140

10 280 HB 0.5 3.2 0.16 0.32 0.96 35 150 22.3 0.27 1120

11 320 HB 0.5 2.4 0.16 0.28 0.64 35 130 22.0 0.25 1100

11 350 HB 0.5 2.4 0.16 0.28 0.64 35 110 22.0 0.25 990

14 180 HB 0.5 4.0 0.18 0.32 0.96 85 270 22.7 0.23 1190

14 240 HB 0.5 4.0 0.18 0.32 0.80 80 220 22.7 0.20 1170

14 290 HB 0.5 3.2 0.16 0.28 0.64 40 150 22.3 0.22 1100

14 310 HB 0.5 3.2 0.16 0.28 0.64 35 140 22.3 0.22 990

12 200 HB 0.5 4.0 0.16 0.32 0.56 85 250 22.3 0.18 1190

13 42 HRc 0.5 3.2 0.16 0.32 0.56 60 190 22.0 0.18 1130

17,19 150 HB 0.5 4.0 0.14 0.40 1.20 60 250 22.7 0.27 1180

17,19 200 HB 0.5 4.0 0.14 0.40 1.04 60 230 22.7 0.27 1160

18,20 250 HB 0.5 4.0 0.14 0.40 0.96 60 190 22.7 0.27 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

VNMG 160408 NN – LT 1005


1 125 HB 0.5 4.0 0.19 0.40 1.44 180 430 22.7 0.34 2265

2 190 HB 0.5 4.0 0.19 0.40 1.44 180 365 22.7 0.32 2240

3 250 HB 0.5 4.0 0.19 0.36 1.20 180 325 22.7 0.30 2220

6 180 HB 0.5 4.0 0.19 0.36 0.96 120 365 22.7 0.29 2220

4,6 230 HB 0.5 3.2 0.19 0.36 0.96 120 325 22.7 0.29 2200

5,7 280 HB 0.5 3.2 0.16 0.32 0.96 120 275 22.7 0.27 1165

8 350 HB 0.5 2.8 0.16 0.32 0.80 120 235 22.4 0.27 1145

10 220 HB 0.5 3.2 0.16 0.32 0.96 70 245 22.3 0.27 1155

10 280 HB 0.5 3.2 0.16 0.32 0.96 70 195 22.3 0.27 1130

11 320 HB 0.5 2.4 0.16 0.28 0.64 70 170 22.0 0.25 1110

11 350 HB 0.5 2.4 0.16 0.28 0.64 70 145 22.0 0.25 1100

15 150 HB 0.5 4.0 0.14 0.48 1.60 170 325 22.7 0.32 2220

15 200 HB 0.5 4.0 0.14 0.48 1.44 160 300 22.7 0.32 2200

16 250 HB 0.5 4.0 0.14 0.44 1.44 150 275 22.7 0.32 1175

17,19 150 HB 0.5 4.0 0.14 0.40 1.20 120 325 22.7 0.27 2200

17,19 200 HB 0.5 4.0 0.14 0.40 1.04 120 300 22.7 0.27 1175

18,20 250 HB 0.5 4.0 0.14 0.40 0.96 120 245 22.7 0.27 1155

38 45 HRc 0.5 2.0 0.10 0.24 0.48 50 130 11.8 0.23 990

38 50 HRc 0.5 1.6 0.10 0.20 0.32 40 115 11.4 0.18 775

38 55 HRc 0.5 1.2 0.10 0.16 0.24 40 105 00.9 0.16 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

138

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


FProductivity

Shape ToleranceClearance Angle

0°80° m

l

Ø d

s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13

Fixing,Chipbreaker

s



T00028411.204.768WNMA 080412 LT 1005


T00028400.804.768WNMA 080408 LT 1005

Application Guide

LT 1005

VC

Productivity

139


WNMA 080408 – LT 1005

WNMA 080412 – LT 1005


15 150 HB 0.7 4.0 0.20 0.60 1.7 270 450 33.5 0.40 3350

15 200 HB 0.7 4.0 0.20 0.58 1.5 200 320 33.5 0.40 2250

16 250 HB 0.7 4.0 0.20 0.56 1.5 170 240 33.5 0.40 2220

17,19 150 HB 0.7 4.0 0.20 0.52 1.3 130 260 33.0 0.30 2240

17,19 200 HB 0.7 4.0 0.20 0.50 1.1 130 230 33.0 0.30 2210

18,20 250 HB 0.7 4.0 0.20 0.48 1.0 130 190 33.0 0.30 1180




No30B


11

GGG40, GGG70, 50005


15 150 HB 0.7 4.0 0.20 0.40 1.4 270 450 33.5 0.32 3350

15 200 HB 0.7 4.0 0.20 0.38 1.2 200 320 33.5 0.32 2250

16 250 HB 0.7 4.0 0.20 0.36 1.2 170 240 33.5 0.32 2220

17,19 150 HB 0.7 4.0 0.20 0.40 1.0 130 260 22.5 0.30 2240

17,19 200 HB 0.7 4.0 0.20 0.38 0.9 130 230 22.5 0.30 2210

18,20 250 HB 0.7 4.0 0.20 0.36 0.8 130 190 22.5 0.30 1180



GGG40, GGG70, 50005


No30B


WNMA


GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters



GroupMaterial

ExemplesHardness

D.O.C [mm]Feed

[mm/rev] Amax[mm2]


Parameters







Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron






Cast

Iron

Grey

Malleable & Nodular

H

Chilled Cast Iron

White Cast Iron

140

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


W N M G

Shape ToleranceClearance Angle Fixing,Chipbreaker

0°80° m

l

Ø d

ss

s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13



T00000771.204.768WNMG 080412 NN LT 10

T00019670.804.768WNMG 080408 NM LT 10

T00000750.804.768WNMG 080408 NN LT 10

T00005840.404.768WNMG 080404 NN LT 10

T00001370.804.766WNMG 060408 NN LT 10

T00001330.404.766WNMG 060404 NN LT 10

Application Guide


LT 1000 Multi-MatTM General Usage - Premium

T00019531.204.768WNMG 080412 NN LT 1000

T00027420.804.768WNMG 080408 NX LT 1000

T00019690.804.768WNMG 080408 NM LT 1000

T00019520.804.768WNMG 080408 NN LT 1000

T00019510.404.768WNMG 080404 NN LT 1000

T00030140.804.766WNMG 060408 NX LT 1000

T00019500.804.766WNMG 060408 NN LT 1000

T00019490.404.766WNMG 060404 NN LT 1000

Application Guide

80° trigon shape inserts with 6 cutting edges. Suitable for all-purpose turning, facing and boring opera-tions.

LT 10 and LT 1000


LT 10 and LT 1000

NX-CNMP-TNMP-WNMP



FProductivity

Stainless Steel

VC


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


141

TURNING



T00041561.204.768WNMG 080412 NN LT 1025

T00041550.804.768WNMG 080408 NX LT 1025

T00041530.804.768WNMG 080408 NM LT 1025

T00041540.804.768WNMG 080408 NN LT 1025

T00041510.804.766WNMG 060408 NX LT 1025

T00041500.804.766WNMG 060408 NN LT 1025

Application Guide



T00041051.204.768WNMG 080412 NN LT 1005

T00041040.804.768WNMG 080408 NX LT 1005

T00041020.804.768WNMG 080408 NM LT 1005

T00041030.804.768WNMG 080408 NN LT 1005

T00041000.804.766WNMG 060408 NX LT 1005

T00040990.804.766WNMG 060408 NN LT 1005

Application Guide


NX-CNMP-TNMP-WNMP


Productivity

W N M G

WNMG

142



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350


St

eel


Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

WNMG 060404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






143



1 125 HB 0.5 2.5 0.21 0.50 1.17 180 330 22.2 0.35 2240

2 190 HB 0.5 2.5 0.21 0.50 1.17 180 280 22.2 0.35 2220

3 250 HB 0.5 2.5 0.21 0.45 0.98 180 250 22.2 0.35 2200

6 180 HB 0.5 2.5 0.21 0.45 0.78 120 280 22.2 0.32 2200

4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 250 11.8 0.32 1180

5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 210 11.8 0.30 1150

8 350 HB 0.5 1.8 0.18 0.40 0.65 120 180 11.6 0.30 1130

10 220 HB 0.5 2.0 0.18 0.40 0.78 70 190 11.8 0.30 1140

10 280 HB 0.5 2.0 0.18 0.40 0.78 70 150 11.8 0.30 1120

11 320 HB 0.5 1.5 0.18 0.35 0.52 70 130 11.5 0.28 1100

11 350 HB 0.5 1.5 0.18 0.35 0.52 70 110 11.5 0.28 990

14 180 HB 0.5 2.5 0.20 0.40 0.78 170 270 22.2 0.35 1190

14 240 HB 0.5 2.5 0.20 0.40 0.65 160 220 22.2 0.32 1170

14 290 HB 0.5 2.0 0.18 0.35 0.52 80 150 11.8 0.28 1100

14 310 HB 0.5 2.0 0.18 0.35 0.52 70 140 11.8 0.28 990

12 200 HB 0.5 2.5 0.22 0.40 0.65 170 250 22.2 0.32 1190

13 42 HRc 0.5 2.0 0.22 0.40 0.65 120 190 22.0 0.32 1130

15 150 HB 0.5 2.5 0.15 0.60 1.30 170 250 22.2 0.35 2200

15 200 HB 0.5 2.5 0.15 0.60 1.17 160 230 22.2 0.35 1180

16 250 HB 0.5 2.5 0.15 0.55 1.17 150 210 22.2 0.35 1160

17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 250 22.2 0.30 1180

17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 230 22.2 0.30 1160

18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 190 22.2 0.30 1140

31,32 Incoloy 800 240 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 332

33 Inconel 700 250 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 330

34 Stellite 21 350 HB 0.5 1.5 0.20 0.35 0.46 23 40 11.5 0.28 228

36 TiAl6V4 - 0.5 2.0 0.20 0.40 0.52 45 65 11.5 0.33 555

37 T40 - 0.5 1.5 0.20 0.35 0.46 35 55 11.5 0.30 445

38 45 HRc 0.5 1.6 0.11 0.30 0.39 50 100 11.5 0.25 880

38 50 HRc 0.5 1.3 0.11 0.25 0.26 40 90 11.0 0.20 770

38 55 HRc 0.5 1.3 0.11 0.20 0.20 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.20 0.60 1.80 200 400 22.2 0.40 280

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

WNMG 060408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






144


WNMG 060408 NN – LT 1025


1 125 HB 0.5 2.5 0.21 0.50 1.17 90 330 11.8 0.38 2240

2 190 HB 0.5 2.5 0.21 0.50 1.17 90 280 11.8 0.35 2220

3 250 HB 0.5 2.5 0.21 0.45 0.98 90 250 11.8 0.33 2200

6 180 HB 0.5 2.5 0.21 0.45 0.78 60 280 11.8 0.32 2200

4,6 230 HB 0.5 2.0 0.21 0.45 0.78 60 250 11.8 0.32 1180

5,7 280 HB 0.5 2.0 0.18 0.40 0.78 60 210 11.8 0.30 1150

8 350 HB 0.5 1.8 0.18 0.40 0.65 60 180 11.6 0.30 1130

10 220 HB 0.5 2.0 0.18 0.40 0.78 35 190 11.5 0.30 1140

10 280 HB 0.5 2.0 0.18 0.40 0.78 35 150 11.5 0.30 1120

11 320 HB 0.5 1.5 0.18 0.35 0.52 35 130 11.3 0.28 1100

11 350 HB 0.5 1.5 0.18 0.35 0.52 35 110 11.3 0.28 990

14 180 HB 0.5 2.5 0.20 0.40 0.78 85 270 11.8 0.25 1190

14 240 HB 0.5 2.5 0.20 0.40 0.65 80 220 11.8 0.22 1170

14 290 HB 0.5 2.0 0.18 0.35 0.52 40 150 11.5 0.24 1100

14 310 HB 0.5 2.0 0.18 0.35 0.52 35 140 11.5 0.24 990

12 200 HB 0.5 2.5 0.18 0.40 0.46 85 250 11.5 0.20 1190

13 42 HRc 0.5 2.0 0.18 0.40 0.46 60 190 11.3 0.20 1130

17,19 150 HB 0.5 2.5 0.15 0.50 0.98 60 250 11.8 0.30 1180

17,19 200 HB 0.5 2.5 0.15 0.50 0.85 60 230 11.8 0.30 1160

18,20 250 HB 0.5 2.5 0.15 0.50 0.78 60 190 11.8 0.30 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

WNMG 060408 NN – LT 1005


1 125 HB 0.5 2.5 0.21 0.50 1.17 180 430 11.8 0.38 2265

2 190 HB 0.5 2.5 0.21 0.50 1.17 180 365 11.8 0.35 2240

3 250 HB 0.5 2.5 0.21 0.45 0.98 180 325 11.8 0.33 2220

6 180 HB 0.5 2.5 0.21 0.45 0.78 120 365 11.8 0.32 2220

4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 325 11.8 0.32 2200

5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 275 11.8 0.30 1165

8 350 HB 0.5 1.8 0.18 0.40 0.65 120 235 11.6 0.30 1145

10 220 HB 0.5 2.0 0.18 0.40 0.78 70 245 11.5 0.30 1155

10 280 HB 0.5 2.0 0.18 0.40 0.78 70 195 11.5 0.30 1130

11 320 HB 0.5 1.5 0.18 0.35 0.52 70 170 11.3 0.28 1110

11 350 HB 0.5 1.5 0.18 0.35 0.52 70 145 11.3 0.28 1100

15 150 HB 0.5 2.5 0.15 0.60 1.30 170 325 11.8 0.35 2220

15 200 HB 0.5 2.5 0.15 0.60 1.17 160 300 11.8 0.35 2200

16 250 HB 0.5 2.5 0.15 0.55 1.17 150 275 11.8 0.35 1175

17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 325 11.8 0.30 2200

17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 300 11.8 0.30 1175

18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 245 11.8 0.30 1155

38 45 HRc 0.5 1.3 0.11 0.30 0.39 50 130 11.2 0.25 990

38 50 HRc 0.5 1.0 0.11 0.25 0.26 40 115 00.9 0.20 775

38 55 HRc 0.5 0.8 0.11 0.20 0.20 40 105 00.6 0.18 665



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

145



1 125 HB 0.5 2.5 0.18 0.50 1.13 180 330 11.8 0.36 2240

2 190 HB 0.5 2.5 0.18 0.50 1.13 180 280 11.8 0.33 2220

3 250 HB 0.5 2.5 0.18 0.45 0.95 180 250 11.8 0.31 2200

6 180 HB 0.5 2.5 0.18 0.45 0.76 120 280 11.8 0.30 2200

4,6 230 HB 0.5 2.0 0.18 0.45 0.76 120 250 11.8 0.30 1180

5,7 280 HB 0.5 2.0 0.16 0.40 0.76 120 210 11.8 0.29 1150

8 350 HB 0.5 1.8 0.16 0.40 0.63 120 180 11.6 0.29 1130

10 220 HB 0.5 2.0 0.16 0.40 0.76 70 190 11.5 0.29 1140

10 280 HB 0.5 2.0 0.16 0.40 0.76 70 150 11.5 0.29 1120

11 320 HB 0.5 1.5 0.16 0.35 0.50 70 130 11.3 0.27 1100

11 350 HB 0.5 1.5 0.16 0.35 0.50 70 110 11.3 0.27 990

14 180 HB 0.5 2.5 0.18 0.40 0.76 170 270 11.8 0.24 1190

14 240 HB 0.5 2.5 0.18 0.40 0.63 160 220 11.8 0.21 1170

14 290 HB 0.5 2.0 0.16 0.35 0.50 80 150 11.5 0.23 1100

14 310 HB 0.5 2.0 0.16 0.35 0.50 70 140 11.5 0.23 990

12 200 HB 0.5 2.5 0.16 0.40 0.44 170 250 11.5 0.19 1190

13 42 HRc 0.5 2.0 0.16 0.40 0.44 120 190 11.3 0.19 1130

15 150 HB 0.5 2.5 0.13 0.60 1.26 170 250 11.8 0.33 2200

15 200 HB 0.5 2.5 0.13 0.60 1.13 160 230 11.8 0.33 1180

16 250 HB 0.5 2.5 0.13 0.55 1.13 150 210 11.8 0.33 1160

17,19 150 HB 0.5 2.5 0.13 0.50 0.95 120 250 11.8 0.29 1180

17,19 200 HB 0.5 2.5 0.13 0.50 0.82 120 230 11.8 0.29 1160

18,20 250 HB 0.5 2.5 0.13 0.50 0.76 120 190 11.8 0.29 1140

31,32 Incoloy 800 240 HB 0.5 1.5 0.18 0.35 0.44 25 45 11.2 0.27 330

33 Inconel 700 250 HB 0.5 1.5 0.18 0.35 0.44 25 45 11.2 0.27 330

34 Stellite 21 350 HB 0.5 1.5 0.18 0.35 0.44 25 40 11.2 0.27 330

36 TiAl6V4 - 0.5 1.8 0.18 0.40 0.50 45 65 11.2 0.31 555

37 T40 - 0.5 1.5 0.18 0.35 0.44 35 55 11.2 0.29 445

38 45 HRc 0.5 1.3 0.10 0.30 0.38 50 100 11.2 0.24 880

38 50 HRc 0.5 1.0 0.10 0.25 0.25 40 90 00.9 0.19 770

38 55 HRc 0.5 0.8 0.10 0.20 0.19 40 80 00.6 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.18 0.60 1.13 200 400 1.8 0.38 280


St

eel


Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

WNMG 060408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






146


WNMG 060408 NX – LT 1025


1 125 HB 0.5 2.5 0.18 0.50 1.13 90 330 11.8 0.36 2240

2 190 HB 0.5 2.5 0.18 0.50 1.13 90 280 11.8 0.33 2220

3 250 HB 0.5 2.5 0.18 0.45 0.95 90 250 11.8 0.31 2200

6 180 HB 0.5 2.5 0.18 0.45 0.76 60 280 11.8 0.30 2200

4,6 230 HB 0.5 2.0 0.18 0.45 0.76 60 250 11.8 0.30 1180

5,7 280 HB 0.5 2.0 0.16 0.40 0.76 60 210 11.8 0.29 1150

8 350 HB 0.5 1.8 0.16 0.40 0.63 60 180 11.6 0.29 1130

10 220 HB 0.5 2.0 0.16 0.40 0.76 35 190 11.5 0.29 1140

10 280 HB 0.5 2.0 0.16 0.40 0.76 35 150 11.5 0.29 1120

11 320 HB 0.5 1.5 0.16 0.35 0.50 35 130 11.3 0.27 1100

11 350 HB 0.5 1.5 0.16 0.35 0.50 35 110 11.3 0.27 990

14 180 HB 0.5 2.5 0.18 0.40 0.76 85 270 11.8 0.24 1190

14 240 HB 0.5 2.5 0.18 0.40 0.63 80 220 11.8 0.21 1170

14 290 HB 0.5 2.0 0.16 0.35 0.50 40 150 11.5 0.23 1100

14 310 HB 0.5 2.0 0.16 0.35 0.50 35 140 11.5 0.23 990

12 200 HB 0.5 2.5 0.16 0.40 0.44 85 250 11.5 0.19 1190

13 42 HRc 0.5 2.0 0.16 0.40 0.44 60 190 11.3 0.19 1130

17,19 150 HB 0.5 2.5 0.13 0.50 0.95 60 250 11.8 0.29 1180

17,19 200 HB 0.5 2.5 0.13 0.50 0.82 60 230 11.8 0.29 1160

18,20 250 HB 0.5 2.5 0.13 0.50 0.76 60 190 11.8 0.29 1140

GGG40, GGG70, 50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

WNMG 060408 NX – LT 1005


1 125 HB 0.5 2.5 0.18 0.50 1.13 180 430 11.8 0.36 2265

2 190 HB 0.5 2.5 0.18 0.50 1.13 180 365 11.8 0.33 2240

3 250 HB 0.5 2.5 0.18 0.45 0.95 180 325 11.8 0.31 2220

6 180 HB 0.5 2.5 0.18 0.45 0.76 120 365 11.8 0.30 2220

4,6 230 HB 0.5 2.0 0.18 0.45 0.76 120 325 11.8 0.30 2200

5,7 280 HB 0.5 2.0 0.16 0.40 0.76 120 275 11.8 0.29 1165

8 350 HB 0.5 1.8 0.16 0.40 0.63 120 235 11.6 0.29 1145

10 220 HB 0.5 2.0 0.16 0.40 0.76 70 245 11.5 0.29 1155

10 280 HB 0.5 2.0 0.16 0.40 0.76 70 195 11.5 0.29 1130

11 320 HB 0.5 1.5 0.16 0.35 0.50 70 170 11.3 0.27 1110

11 350 HB 0.5 1.5 0.16 0.35 0.50 70 145 11.3 0.27 1100

15 150 HB 0.5 2.5 0.13 0.60 1.26 170 325 11.8 0.33 2220

15 200 HB 0.5 2.5 0.13 0.60 1.13 160 300 11.8 0.33 2200

16 250 HB 0.5 2.5 0.13 0.55 1.13 150 275 11.8 0.33 1175

17,19 150 HB 0.5 2.5 0.13 0.50 0.95 120 325 11.8 0.29 2200

17,19 200 HB 0.5 2.5 0.13 0.50 0.82 120 300 11.8 0.29 1175

18,20 250 HB 0.5 2.5 0.13 0.50 0.76 120 245 11.8 0.29 1155

38 45 HRc 0.5 1.3 0.10 0.30 0.38 50 130 11.2 0.24 990

38 50 HRc 0.5 1.0 0.10 0.25 0.25 40 115 00.9 0.19 775

38 55 HRc 0.5 0.8 0.10 0.20 0.19 40 105 00.6 0.17 665




Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



No30B


X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

147



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350


St

eel


Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

WNMG 080404 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






148



1 125 HB 0.5 3.5 0.25 0.65 2.16 180 330 33.0 0.44 2240

2 190 HB 0.5 3.5 0.25 0.65 2.16 180 280 33.0 0.44 2220

3 250 HB 0.5 3.5 0.25 0.59 1.80 180 250 33.0 0.44 2200

6 180 HB 0.5 3.5 0.25 0.59 1.44 120 280 33.0 0.40 2200

4,6 230 HB 0.5 2.8 0.25 0.59 1.44 120 250 33.0 0.40 1180

5,7 280 HB 0.5 2.8 0.22 0.52 1.44 120 210 33.0 0.38 1150

8 350 HB 0.5 2.5 0.22 0.52 1.20 120 180 33.0 0.38 1130

10 220 HB 0.5 2.8 0.22 0.52 1.44 70 190 22.5 0.38 1140

10 280 HB 0.5 2.8 0.22 0.52 1.44 70 150 22.5 0.38 1120

11 320 HB 0.5 2.1 0.22 0.46 0.96 70 130 22.5 0.35 1100

11 350 HB 0.5 2.1 0.22 0.46 0.96 70 110 22.5 0.35 990

14 180 HB 0.5 3.5 0.24 0.52 1.44 170 270 33.0 0.44 1190

14 240 HB 0.5 3.5 0.24 0.52 1.20 160 220 33.0 0.40 1170

14 290 HB 0.5 2.8 0.22 0.46 0.96 80 150 22.5 0.35 1100

14 310 HB 0.5 2.8 0.22 0.46 0.96 70 140 22.5 0.35 990

12 200 HB 0.5 3.5 0.26 0.52 1.20 170 250 33.0 0.40 1190

13 42 HRc 0.5 2.8 0.26 0.52 1.20 120 190 22.5 0.40 1130

15 150 HB 0.5 3.5 0.18 0.78 2.40 170 250 33.0 0.44 2200

15 200 HB 0.5 3.5 0.18 0.78 2.16 160 230 33.0 0.44 1180

16 250 HB 0.5 3.5 0.18 0.72 2.16 150 210 33.0 0.44 1160

17,19 150 HB 0.5 3.5 0.18 0.65 1.80 120 250 33.0 0.38 1180

17,19 200 HB 0.5 3.5 0.18 0.65 1.56 120 230 33.0 0.38 1160

18,20 250 HB 0.5 3.5 0.18 0.65 1.44 120 190 33.0 0.38 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.24 0.46 0.84 25 45 22.0 0.35 332

33 Inconel 700 250 HB 0.5 2.1 0.24 0.46 0.84 25 45 22.0 0.35 330

34 Stellite 21 350 HB 0.5 2.1 0.24 0.46 0.84 23 40 22.0 0.35 228

36 TiAl6V4 - 0.5 2.8 0.24 0.52 0.96 45 65 22.0 0.41 555

37 T40 - 0.5 2.1 0.24 0.46 0.84 35 55 22.0 0.38 445

38 45 HRc 0.5 1.8 0.13 0.39 0.72 50 100 22.0 0.31 880

38 50 HRc 0.5 1.5 0.13 0.33 0.48 40 90 11.5 0.25 770

38 55 HRc 0.5 1.5 0.13 0.26 0.36 40 80 11.0 0.23 660Chilled Cast

IIron40 Ni-Hard 2 400 HB 0.5 1.5 0.13 0.33 0.48 40 60 11.5 0.23 550


NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.24 0.78 2.20 200 400 33.0 0.50 280

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B

Malleable & Nodular

8

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


6 410, X6Cr17, 17-4 PH, 430

Cast

Iron

WNMG 080408 NM – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






149


WNMG 080408 NM – LT 1025


1 125 HB 0.5 3.5 0.25 0.65 2.16 90 330 22.6 0.48 2240

2 190 HB 0.5 3.5 0.25 0.65 2.16 90 280 22.6 0.44 2220

3 250 HB 0.5 3.5 0.25 0.59 1.80 90 250 22.6 0.41 2200

6 180 HB 0.5 3.5 0.25 0.59 1.44 60 280 22.6 0.40 2200

4,6 230 HB 0.5 2.8 0.25 0.59 1.44 60 250 22.6 0.40 1180

5,7 280 HB 0.5 2.8 0.22 0.52 1.44 60 210 22.6 0.38 1150

8 350 HB 0.5 2.5 0.22 0.52 1.20 60 180 22.3 0.38 1130

10 220 HB 0.5 2.8 0.22 0.52 1.44 35 190 22.1 0.38 1140

10 280 HB 0.5 2.8 0.22 0.52 1.44 35 150 22.1 0.38 1120

11 320 HB 0.5 2.1 0.22 0.46 0.96 35 130 11.9 0.35 1100

11 350 HB 0.5 2.1 0.22 0.46 0.96 35 110 11.9 0.35 990

14 180 HB 0.5 3.5 0.24 0.52 1.44 85 270 22.6 0.31 1190

14 240 HB 0.5 3.5 0.24 0.52 1.20 80 220 22.6 0.28 1170

14 290 HB 0.5 2.8 0.22 0.46 0.96 40 150 22.1 0.30 1100

14 310 HB 0.5 2.8 0.22 0.46 0.96 35 140 22.1 0.30 990

12 200 HB 0.5 3.5 0.22 0.52 0.84 85 250 22.1 0.25 1190

13 42 HRc 0.5 2.8 0.22 0.52 0.84 60 190 11.9 0.25 1130

17,19 150 HB 0.5 3.5 0.18 0.65 1.80 60 250 22.6 0.38 1180

17,19 200 HB 0.5 3.5 0.18 0.65 1.56 60 230 22.6 0.38 1160

18,20 250 HB 0.5 3.5 0.18 0.65 1.44 60 190 22.6 0.38 1140


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


WNMG 080408 NM – LT 1005


1 125 HB 0.5 3.5 0.25 0.65 2.16 180 430 22.6 0.48 2265

2 190 HB 0.5 3.5 0.25 0.65 2.16 180 365 22.6 0.44 2240

3 250 HB 0.5 3.5 0.25 0.59 1.80 180 325 22.6 0.41 2220

6 180 HB 0.5 3.5 0.25 0.59 1.44 120 365 22.6 0.40 2220

4,6 230 HB 0.5 2.8 0.25 0.59 1.44 120 325 22.6 0.40 2200

5,7 280 HB 0.5 2.8 0.22 0.52 1.44 120 275 22.6 0.38 1165

8 350 HB 0.5 2.5 0.22 0.52 1.20 120 235 22.3 0.38 1145

10 220 HB 0.5 2.8 0.22 0.52 1.44 70 245 22.1 0.38 1155

10 280 HB 0.5 2.8 0.22 0.52 1.44 70 195 22.1 0.38 1130

11 320 HB 0.5 2.1 0.22 0.46 0.96 70 170 11.9 0.35 1110

11 350 HB 0.5 2.1 0.22 0.46 0.96 70 145 11.9 0.35 1100

15 150 HB 0.5 3.5 0.18 0.78 2.40 170 325 22.6 0.44 2220

15 200 HB 0.5 3.5 0.18 0.78 2.16 160 300 22.6 0.44 2200

16 250 HB 0.5 3.5 0.18 0.72 2.16 150 275 22.6 0.44 1175

17,19 150 HB 0.5 3.5 0.18 0.65 1.80 120 325 22.6 0.38 2200

17,19 200 HB 0.5 3.5 0.18 0.65 1.56 120 300 22.6 0.38 1175

18,20 250 HB 0.5 3.5 0.18 0.65 1.44 120 245 22.6 0.38 1155

38 45 HRc 0.5 1.8 0.13 0.39 0.72 50 130 11.7 0.31 990

38 50 HRc 0.5 1.4 0.13 0.33 0.48 40 115 11.3 0.25 775

38 55 HRc 0.5 1.1 0.13 0.26 0.36 40 105 00.9 0.23 665



X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



Low alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

150



1 125 HB 0.5 3.5 0.21 0.50 1.80 180 330 22.4 0.35 2240

2 190 HB 0.5 3.5 0.21 0.50 1.80 180 280 22.4 0.35 2220

3 250 HB 0.5 3.5 0.21 0.45 1.50 180 250 22.4 0.35 2200

6 180 HB 0.5 3.5 0.21 0.45 1.20 120 280 22.4 0.32 2200

4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 250 22.4 0.32 1180

5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 210 22.4 0.30 1150

8 350 HB 0.5 2.5 0.18 0.40 1.00 120 180 22.4 0.30 1130

10 220 HB 0.5 2.8 0.18 0.40 1.20 70 190 22.0 0.30 1140

10 280 HB 0.5 2.8 0.18 0.40 1.20 70 150 22.0 0.30 1120

11 320 HB 0.5 2.1 0.18 0.35 0.80 70 130 22.0 0.28 1100

11 350 HB 0.5 2.1 0.18 0.35 0.80 70 110 22.0 0.28 990

14 180 HB 0.5 3.5 0.20 0.40 1.20 170 270 22.4 0.35 1190

14 240 HB 0.5 3.5 0.20 0.40 1.00 160 220 22.4 0.32 1170

14 290 HB 0.5 2.8 0.18 0.35 0.80 80 150 22.0 0.28 1100

14 310 HB 0.5 2.8 0.18 0.35 0.80 70 140 22.0 0.28 990

12 200 HB 0.5 3.5 0.22 0.40 1.00 170 250 22.4 0.32 1190

13 42 HRc 0.5 2.8 0.22 0.40 1.00 120 190 22.0 0.32 1130

15 150 HB 0.5 3.5 0.15 0.60 2.00 170 250 22.4 0.35 2200

15 200 HB 0.5 3.5 0.15 0.60 1.80 160 230 22.4 0.35 1180

16 250 HB 0.5 3.5 0.15 0.55 1.80 150 210 22.4 0.35 1160

17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 250 22.4 0.30 1180

17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 230 22.4 0.30 1160

18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 190 22.4 0.30 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.20 0.35 0.70 25 45 11.6 0.28 332

33 Inconel 700 250 HB 0.5 2.1 0.20 0.35 0.70 25 45 11.6 0.28 330

34 Stellite 21 350 HB 0.5 2.1 0.20 0.35 0.70 23 40 11.6 0.28 228

36 TiAl6V4 - 0.5 2.8 0.20 0.40 0.80 45 65 11.6 0.33 555

37 T40 - 0.5 2.1 0.20 0.35 0.70 35 55 11.6 0.30 445

38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 100 11.6 0.25 880

38 50 HRc 0.5 1.5 0.11 0.25 0.40 40 90 11.2 0.20 770

38 55 HRc 0.5 1.5 0.11 0.20 0.30 40 80 00.8 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.20 0.60 1.80 200 400 2.4 0.40 280


St

eel


Low alloyed

D.O.C. [mm]

2



42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

WNMG 080408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






151


WNMG 080408 NN – LT 1025


1 125 HB 0.5 3.5 0.21 0.50 1.80 90 330 22.4 0.38 2240

2 190 HB 0.5 3.5 0.21 0.50 1.80 90 280 22.4 0.35 2220

3 250 HB 0.5 3.5 0.21 0.45 1.50 90 250 22.4 0.33 2200

6 180 HB 0.5 3.5 0.21 0.45 1.20 60 280 22.4 0.32 2200

4,6 230 HB 0.5 2.8 0.21 0.45 1.20 60 250 22.4 0.32 1180

5,7 280 HB 0.5 2.8 0.18 0.40 1.20 60 210 22.4 0.30 1150

8 350 HB 0.5 2.5 0.18 0.40 1.00 60 180 22.2 0.30 1130

10 220 HB 0.5 2.8 0.18 0.40 1.20 35 190 22.0 0.30 1140

10 280 HB 0.5 2.8 0.18 0.40 1.20 35 150 22.0 0.30 1120

11 320 HB 0.5 2.1 0.18 0.35 0.80 35 130 11.8 0.28 1100

11 350 HB 0.5 2.1 0.18 0.35 0.80 35 110 11.8 0.28 990

14 180 HB 0.5 3.5 0.20 0.40 1.20 85 270 22.4 0.25 1190

14 240 HB 0.5 3.5 0.20 0.40 1.00 80 220 22.4 0.22 1170

14 290 HB 0.5 2.8 0.18 0.35 0.80 40 150 22.0 0.24 1100

14 310 HB 0.5 2.8 0.18 0.35 0.80 35 140 22.0 0.24 990

12 200 HB 0.5 3.5 0.18 0.40 0.70 85 250 22.0 0.20 1190

13 42 HRc 0.5 2.8 0.18 0.40 0.70 60 190 11.8 0.20 1130

17,19 150 HB 0.5 3.5 0.15 0.50 1.50 60 250 22.4 0.30 1180

17,19 200 HB 0.5 3.5 0.15 0.50 1.30 60 230 22.4 0.30 1160

18,20 250 HB 0.5 3.5 0.15 0.50 1.20 60 190 22.4 0.30 1140


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


WNMG 080408 NN – LT 1005


1 125 HB 0.5 3.5 0.21 0.50 1.80 180 430 22.4 0.38 2265

2 190 HB 0.5 3.5 0.21 0.50 1.80 180 365 22.4 0.35 2240

3 250 HB 0.5 3.5 0.21 0.45 1.50 180 325 22.4 0.33 2220

6 180 HB 0.5 3.5 0.21 0.45 1.20 120 365 22.4 0.32 2220

4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 325 22.4 0.32 2200

5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 275 22.4 0.30 1165

8 350 HB 0.5 2.5 0.18 0.40 1.00 120 235 22.2 0.30 1145

10 220 HB 0.5 2.8 0.18 0.40 1.20 70 245 22.0 0.30 1155

10 280 HB 0.5 2.8 0.18 0.40 1.20 70 195 22.0 0.30 1130

11 320 HB 0.5 2.1 0.18 0.35 0.80 70 170 11.8 0.28 1110

11 350 HB 0.5 2.1 0.18 0.35 0.80 70 145 11.8 0.28 1100

15 150 HB 0.5 3.5 0.15 0.60 2.00 170 325 22.4 0.35 2220

15 200 HB 0.5 3.5 0.15 0.60 1.80 160 300 22.4 0.35 2200

16 250 HB 0.5 3.5 0.15 0.55 1.80 150 275 22.4 0.35 1175

17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 325 22.4 0.30 2200

17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 300 22.4 0.30 1175

18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 245 22.4 0.30 1155

38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 130 11.6 0.25 990

38 50 HRc 0.5 1.4 0.11 0.25 0.40 40 115 11.2 0.20 775

38 55 HRc 0.5 1.1 0.11 0.20 0.30 40 105 00.8 0.18 665



X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



Low alloyed 2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

152



1 125 HB 0.5 3.5 0.18 0.50 1.71 180 330 22.4 0.36 2240

2 190 HB 0.5 3.5 0.18 0.50 1.71 180 280 22.4 0.33 2220

3 250 HB 0.5 3.5 0.18 0.45 1.43 180 250 22.4 0.31 2200

6 180 HB 0.5 3.5 0.18 0.45 1.14 120 280 22.4 0.30 2200

4,6 230 HB 0.5 2.8 0.18 0.45 1.14 120 250 22.4 0.30 1180

5,7 280 HB 0.5 2.8 0.16 0.40 1.14 120 210 22.4 0.29 1150

8 350 HB 0.5 2.5 0.16 0.40 0.95 120 180 22.2 0.29 1130

10 220 HB 0.5 2.8 0.16 0.40 1.14 70 190 22.0 0.29 1140

10 280 HB 0.5 2.8 0.16 0.40 1.14 70 150 22.0 0.29 1120

11 320 HB 0.5 2.1 0.16 0.35 0.76 70 130 11.8 0.27 1100

11 350 HB 0.5 2.1 0.16 0.35 0.76 70 110 11.8 0.27 990

14 180 HB 0.5 3.5 0.18 0.40 1.14 170 270 22.4 0.24 1190

14 240 HB 0.5 3.5 0.18 0.40 0.95 160 220 22.4 0.21 1170

14 290 HB 0.5 2.8 0.16 0.35 0.76 80 150 22.0 0.23 1100

14 310 HB 0.5 2.8 0.16 0.35 0.76 70 140 22.0 0.23 990

12 200 HB 0.5 3.5 0.16 0.40 0.67 170 250 22.0 0.19 1190

13 42 HRc 0.5 2.8 0.16 0.40 0.67 120 190 11.8 0.19 1130

15 150 HB 0.5 3.5 0.13 0.60 1.90 170 250 22.4 0.33 2200

15 200 HB 0.5 3.5 0.13 0.60 1.71 160 230 22.4 0.33 1180

16 250 HB 0.5 3.5 0.13 0.55 1.71 150 210 22.4 0.33 1160

17,19 150 HB 0.5 3.5 0.13 0.50 1.43 120 250 22.4 0.29 1180

17,19 200 HB 0.5 3.5 0.13 0.50 1.24 120 230 22.4 0.29 1160

18,20 250 HB 0.5 3.5 0.13 0.50 1.14 120 190 22.4 0.29 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.18 0.35 0.67 25 45 11.6 0.27 330

33 Inconel 700 250 HB 0.5 2.1 0.18 0.35 0.67 25 45 11.6 0.27 330

34 Stellite 21 350 HB 0.5 2.1 0.18 0.35 0.67 25 40 11.6 0.27 330

36 TiAl6V4 - 0.5 2.5 0.18 0.40 0.76 45 65 11.6 0.31 555

37 T40 - 0.5 2.1 0.18 0.35 0.67 35 55 11.6 0.29 445

38 45 HRc 0.5 1.8 0.10 0.30 0.57 50 100 11.6 0.24 880

38 50 HRc 0.5 1.4 0.10 0.25 0.38 40 90 11.2 0.19 770

38 55 HRc 0.5 1.1 0.10 0.20 0.29 40 80 00.8 0.17 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.18 0.60 1.71 200 400 2.4 0.38 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5


1C35, Ck45, 1020, 1045, 1060, 28Mn6

D.O.C. [mm]

2

Gr. N°VDI


WNMG 080408 NX – LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






153


WNMG 080408 NX – LT 1025


1 125 HB 0.5 3.5 0.18 0.50 1.71 90 330 22.4 0.36 2240

2 190 HB 0.5 3.5 0.18 0.50 1.71 90 280 22.4 0.33 2220

3 250 HB 0.5 3.5 0.18 0.45 1.43 90 250 22.4 0.31 2200

6 180 HB 0.5 3.5 0.18 0.45 1.14 60 280 22.4 0.30 2200

4,6 230 HB 0.5 2.8 0.18 0.45 1.14 60 250 22.4 0.30 1180

5,7 280 HB 0.5 2.8 0.16 0.40 1.14 60 210 22.4 0.29 1150

8 350 HB 0.5 2.5 0.16 0.40 0.95 60 180 22.2 0.29 1130

10 220 HB 0.5 2.8 0.16 0.40 1.14 35 190 22.0 0.29 1140

10 280 HB 0.5 2.8 0.16 0.40 1.14 35 150 22.0 0.29 1120

11 320 HB 0.5 2.1 0.16 0.35 0.76 35 130 11.8 0.27 1100

11 350 HB 0.5 2.1 0.16 0.35 0.76 35 110 11.8 0.27 990

14 180 HB 0.5 3.5 0.18 0.40 1.14 85 270 22.4 0.24 1190

14 240 HB 0.5 3.5 0.18 0.40 0.95 80 220 22.4 0.21 1170

14 290 HB 0.5 2.8 0.16 0.35 0.76 40 150 22.0 0.23 1100

14 310 HB 0.5 2.8 0.16 0.35 0.76 35 140 22.0 0.23 990

12 200 HB 0.5 3.5 0.16 0.40 0.67 85 250 22.0 0.19 1190

13 42 HRc 0.5 2.8 0.16 0.40 0.67 60 190 11.8 0.19 1130

17,19 150 HB 0.5 3.5 0.13 0.50 1.43 60 250 22.4 0.29 1180

17,19 200 HB 0.5 3.5 0.13 0.50 1.24 60 230 22.4 0.29 1160

18,20 250 HB 0.5 3.5 0.13 0.50 1.14 60 190 22.4 0.29 1140


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


50005

X2CrNiN23-4, S31500


WNMG 080408 NX – LT 1005


1 125 HB 0.5 3.5 0.18 0.50 1.71 180 430 22.4 0.36 2265

2 190 HB 0.5 3.5 0.18 0.50 1.71 180 365 22.4 0.33 2240

3 250 HB 0.5 3.5 0.18 0.45 1.43 180 325 22.4 0.31 2220

6 180 HB 0.5 3.5 0.18 0.45 1.14 120 365 22.4 0.30 2220

4,6 230 HB 0.5 2.8 0.18 0.45 1.14 120 325 22.4 0.30 2200

5,7 280 HB 0.5 2.8 0.16 0.40 1.14 120 275 22.4 0.29 1165

8 350 HB 0.5 2.5 0.16 0.40 0.95 120 235 22.2 0.29 1145

10 220 HB 0.5 2.8 0.16 0.40 1.14 70 245 22.0 0.29 1155

10 280 HB 0.5 2.8 0.16 0.40 1.14 70 195 22.0 0.29 1130

11 320 HB 0.5 2.1 0.16 0.35 0.76 70 170 11.8 0.27 1110

11 350 HB 0.5 2.1 0.16 0.35 0.76 70 145 11.8 0.27 1100

15 150 HB 0.5 3.5 0.13 0.60 1.90 170 325 22.4 0.33 2220

15 200 HB 0.5 3.5 0.13 0.60 1.71 160 300 22.4 0.33 2200

16 250 HB 0.5 3.5 0.13 0.55 1.71 150 275 22.4 0.33 1175

17,19 150 HB 0.5 3.5 0.13 0.50 1.43 120 325 22.4 0.29 2200

17,19 200 HB 0.5 3.5 0.13 0.50 1.24 120 300 22.4 0.29 1175

18,20 250 HB 0.5 3.5 0.13 0.50 1.14 120 245 22.4 0.29 1155

38 45 HRc 0.5 1.8 0.10 0.30 0.57 50 130 11.6 0.24 990

38 50 HRc 0.5 1.4 0.10 0.25 0.38 40 115 11.2 0.19 775

38 55 HRc 0.5 1.1 0.10 0.20 0.29 40 105 00.8 0.17 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

154



1 125 HB 0.7 3.5 0.25 0.65 2.16 180 330 33.0 0.44 2240

2 190 HB 0.7 3.5 0.25 0.65 2.16 180 280 33.0 0.44 2220

3 250 HB 0.7 3.5 0.25 0.59 1.80 180 250 33.0 0.44 2200

6 180 HB 0.7 3.5 0.25 0.59 1.44 120 280 33.0 0.40 2200

4,6 230 HB 0.7 2.8 0.25 0.59 1.44 120 250 33.0 0.40 1180

5,7 280 HB 0.7 2.8 0.22 0.52 1.44 120 210 33.0 0.38 1150

8 350 HB 0.7 2.5 0.22 0.52 1.20 120 180 33.0 0.38 1130

10 220 HB 0.7 2.8 0.22 0.52 1.44 70 190 22.5 0.38 1140

10 280 HB 0.7 2.8 0.22 0.52 1.44 70 150 22.5 0.38 1120

11 320 HB 0.7 2.1 0.22 0.46 0.96 70 130 22.5 0.35 1100

11 350 HB 0.7 2.1 0.22 0.46 0.96 70 110 22.5 0.35 990

14 180 HB 0.7 3.5 0.24 0.52 1.44 170 270 33.0 0.40 1190

14 240 HB 0.7 3.5 0.24 0.52 1.20 160 220 33.0 0.36 1170

14 290 HB 0.7 2.8 0.22 0.46 0.96 80 150 22.5 0.32 1100

14 310 HB 0.7 2.8 0.22 0.46 0.96 70 140 22.5 0.32 990

12 200 HB 0.7 3.5 0.26 0.52 1.20 170 250 33.0 0.40 1190

13 42 HRc 0.7 2.8 0.26 0.52 1.20 120 190 22.5 0.36 1130

15 150 HB 0.7 3.5 0.18 0.78 2.40 170 250 33.0 0.44 2200

15 200 HB 0.7 3.5 0.18 0.78 2.16 160 230 33.0 0.44 1180

16 250 HB 0.7 3.5 0.18 0.72 2.16 150 210 33.0 0.44 1160

17,19 150 HB 0.7 3.5 0.18 0.65 1.80 120 250 33.0 0.38 1180

17,19 200 HB 0.7 3.5 0.18 0.65 1.56 120 230 33.0 0.38 1160

18,20 250 HB 0.7 3.5 0.18 0.65 1.44 120 190 33.0 0.38 1140

31,32 Incoloy 800 240 HB 0.7 2.1 0.24 0.46 0.84 25 45 22.0 0.35 332

33 Inconel 700 250 HB 0.7 2.1 0.24 0.46 0.84 25 45 22.0 0.35 330

34 Stellite 21 350 HB 0.7 2.1 0.24 0.46 0.84 23 40 22.0 0.35 228

36 TiAl6V4 - 0.7 2.8 0.24 0.52 0.96 45 65 22.0 0.40 555

37 T40 - 0.7 2.1 0.24 0.46 0.84 35 55 22.0 0.36 445

38 45 HRc 0.7 1.8 0.13 0.39 0.72 50 100 22.0 0.31 880

38 50 HRc 0.7 1.5 0.13 0.33 0.48 40 90 11.5 0.25 770

38 55 HRc 0.7 1.5 0.13 0.26 0.36 40 80 11.0 0.23 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.7 4.2 0.24 0.78 2.20 200 400 3.0 0.50 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



WNMG 080412 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






155


WNMG 080412 NN – LT 1025


1 125 HB 0.7 3.5 0.25 0.65 2.16 90 330 22.6 0.48 2240

2 190 HB 0.7 3.5 0.25 0.65 2.16 90 280 22.6 0.44 2220

3 250 HB 0.7 3.5 0.25 0.59 1.80 90 250 22.6 0.41 2200

6 180 HB 0.7 3.5 0.25 0.59 1.44 60 280 22.6 0.40 2200

4,6 230 HB 0.7 2.8 0.25 0.59 1.44 60 250 22.6 0.40 1180

5,7 280 HB 0.7 2.8 0.22 0.52 1.44 60 210 22.6 0.38 1150

8 350 HB 0.7 2.5 0.22 0.52 1.20 60 180 22.3 0.38 1130

10 220 HB 0.7 2.8 0.22 0.52 1.44 35 190 22.1 0.38 1140

10 280 HB 0.7 2.8 0.22 0.52 1.44 35 150 22.1 0.38 1120

11 320 HB 0.7 2.1 0.22 0.46 0.96 35 130 11.9 0.35 1100

11 350 HB 0.7 2.1 0.22 0.46 0.96 35 110 11.9 0.35 990

14 180 HB 0.7 3.5 0.24 0.52 1.44 85 270 22.6 0.31 1190

14 240 HB 0.7 3.5 0.24 0.52 1.20 80 220 22.6 0.28 1170

14 290 HB 0.7 2.8 0.22 0.46 0.96 40 150 22.1 0.30 1100

14 310 HB 0.7 2.8 0.22 0.46 0.96 35 140 22.1 0.30 990

12 200 HB 0.7 3.5 0.22 0.52 0.84 85 250 22.1 0.25 1190

13 42 HRc 0.7 2.8 0.22 0.52 0.84 60 190 11.9 0.25 1130

17,19 150 HB 0.7 3.5 0.18 0.65 1.80 60 250 22.6 0.38 1180

17,19 200 HB 0.7 3.5 0.18 0.65 1.56 60 230 22.6 0.38 1160

18,20 250 HB 0.7 3.5 0.18 0.65 1.44 60 190 22.6 0.38 1140

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

8GGG40, GGG70,

50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

WNMG 080412 NN – LT 1005


1 125 HB 0.7 3.5 0.25 0.65 2.16 180 430 22.6 0.48 2265

2 190 HB 0.7 3.5 0.25 0.65 2.16 180 365 22.6 0.44 2240

3 250 HB 0.7 3.5 0.25 0.59 1.80 180 325 22.6 0.41 2220

6 180 HB 0.7 3.5 0.25 0.59 1.44 120 365 22.6 0.40 2220

4,6 230 HB 0.7 2.8 0.25 0.59 1.44 120 325 22.6 0.40 2200

5,7 280 HB 0.7 2.8 0.22 0.52 1.44 120 275 22.6 0.38 1165

8 350 HB 0.7 2.5 0.22 0.52 1.20 120 235 22.3 0.38 1145

10 220 HB 0.7 2.8 0.22 0.52 1.44 70 245 22.1 0.38 1155

10 280 HB 0.7 2.8 0.22 0.52 1.44 70 195 22.1 0.38 1130

11 320 HB 0.7 2.1 0.22 0.46 0.96 70 170 11.9 0.35 1110

11 350 HB 0.7 2.1 0.22 0.46 0.96 70 145 11.9 0.35 1100

15 150 HB 0.7 3.5 0.18 0.78 2.40 170 325 22.6 0.44 2220

15 200 HB 0.7 3.5 0.18 0.78 2.16 160 300 22.6 0.44 2200

16 250 HB 0.7 3.5 0.18 0.72 2.16 150 275 22.6 0.44 1175

17,19 150 HB 0.7 3.5 0.18 0.65 1.80 120 325 22.6 0.38 2200

17,19 200 HB 0.7 3.5 0.18 0.65 1.56 120 300 22.6 0.38 1175

18,20 250 HB 0.7 3.5 0.18 0.65 1.44 120 245 22.6 0.38 1155

38 45 HRc 0.7 1.8 0.13 0.39 0.72 50 130 11.7 0.31 990

38 50 HRc 0.7 1.4 0.13 0.33 0.48 40 115 11.3 0.25 775

38 55 HRc 0.7 1.1 0.13 0.26 0.36 40 105 00.9 0.23 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

156

TURNING


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


NXCNMPTNMPWNMP

FProductivity

Exotic Material


Stainless Steel

VC

W N M P


0° m

l

Fixing,Chipbreaker

80°

ss

s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13

F M R

Application Guide



T00003080.804.768WNMP 080408 NN LT 10

T00003070.804.766WNMP 060408 NN LT 10

T00003060.404.766WNMP 060404 NN LT 10

F M R

Application Guide



T00041060.804.768WNMP 080408 NN LT 1005

F M R

Application Guide



T00041570.804.768WNMP 080408 NN LT 1025

F M R

Application Guide


T00019560.804.768WNMP 080408 NN LT 1000

T00019550.804.766WNMP 060408 NN LT 1000

T00019540.404.766WNMP 060404 NN LT 1000


80° trigone shape inserts with positive chipbreaker geometry. Generates lower cutting forces. Suitable for high temperature alloys and stainless steel operations.


157



1 125 HB 0.3 3.0 0.11 0.23 0.60 180 330 22.0 0.18 3300

2 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 22.0 0.18 2260

3 250 HB 0.3 2.5 0.11 0.20 0.48 180 250 22.0 0.18 2240

6 180 HB 0.3 2.5 0.10 0.20 0.50 120 280 22.0 0.14 2260

4,6 230 HB 0.3 2.5 0.10 0.20 0.48 120 250 22.0 0.14 2240

5,7 280 HB 0.3 2.0 0.10 0.18 0.40 120 210 22.0 0.13 2200

8 350 HB 0.3 2.0 0.10 0.18 0.36 120 180 22.0 0.13 1180

10 220 HB 0.3 2.5 0.09 0.18 0.40 70 190 11.7 0.10 1180

10 280 HB 0.3 2.5 0.09 0.16 0.40 70 150 11.7 0.10 1140

11 320 HB 0.3 2.0 0.09 0.14 0.32 70 130 11.7 0.10 1120

11 350 HB 0.3 2.0 0.09 0.14 0.26 70 110 11.7 0.10 1110

14 180 HB 0.3 2.5 0.08 0.18 0.32 170 270 22.0 0.09 2260

14 240 HB 0.3 2.5 0.08 0.18 0.26 160 220 22.0 0.08 2210

14 290 HB 0.3 2.0 0.08 0.14 0.20 80 150 11.7 0.08 1140

14 310 HB 0.3 2.0 0.08 0.14 0.20 70 140 11.7 0.08 1140

12 200 HB 0.3 2.5 0.08 0.18 0.32 170 250 11.7 0.09 2240

13 42 HRc 0.3 2.0 0.08 0.16 0.26 120 190 11.5 0.08 1180

15 150 HB 0.3 3.0 0.08 0.20 0.64 170 250 22.0 0.18 2240

15 200 HB 0.3 3.0 0.08 0.20 0.60 160 230 22.0 0.18 2220

16 250 HB 0.3 3.0 0.08 0.20 0.60 150 210 22.0 0.18 2200

17,19 150 HB 0.3 2.5 0.08 0.18 0.48 120 250 22.0 0.13 2240

17,19 200 HB 0.3 2.5 0.08 0.18 0.40 120 230 22.0 0.13 2220

18,20 250 HB 0.3 2.5 0.08 0.18 0.40 120 190 22.0 0.13 1180

31,32 Incoloy 800 240 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

33 Inconel 700 250 HB 0.3 2.0 0.09 0.15 0.26 25 50 11.3 0.10 440

34 Stellite 21 350 HB 0.3 2.0 0.09 0.15 0.26 23 45 11.3 0.10 335

36 TiAl6V4 - 0.3 2.0 0.09 0.16 0.32 45 65 11.3 0.14 660

37 T40 - 0.3 2.0 0.09 0.14 0.26 35 60 11.3 0.10 550

38 45 HRc 0.3 1.8 0.05 0.12 0.20 50 100 11.4 0.10 990

38 50 HRc 0.3 1.5 0.05 0.10 0.17 40 90 11.1 0.08 880

38 55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 00.9 0.06 770



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 4.0 0.10 0.30 0.70 200 400 2.0 0.23 350

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

WNMP 060404 NN – LT 10 | LT 1000

WNMP

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






158



1 125 HB 0.5 2.5 0.21 0.50 1.17 180 330 22.2 0.35 2240

2 190 HB 0.5 2.5 0.21 0.50 1.17 180 280 22.2 0.35 2220

3 250 HB 0.5 2.5 0.21 0.45 0.98 180 250 22.2 0.35 2200

6 180 HB 0.5 2.5 0.21 0.45 0.78 120 280 22.2 0.32 2200

4,6 230 HB 0.5 2.0 0.21 0.45 0.78 120 250 11.8 0.32 1180

5,7 280 HB 0.5 2.0 0.18 0.40 0.78 120 210 11.8 0.30 1150

8 350 HB 0.5 1.8 0.18 0.40 0.65 120 180 11.6 0.30 1130

10 220 HB 0.5 2.0 0.18 0.40 0.78 70 190 11.8 0.30 1140

10 280 HB 0.5 2.0 0.18 0.40 0.78 70 150 11.8 0.30 1120

11 320 HB 0.5 1.5 0.18 0.35 0.52 70 130 11.5 0.28 1100

11 350 HB 0.5 1.5 0.18 0.35 0.52 70 110 11.5 0.28 990

14 180 HB 0.5 2.5 0.20 0.40 0.78 170 270 22.2 0.35 1190

14 240 HB 0.5 2.5 0.20 0.40 0.65 160 220 22.2 0.32 1170

14 290 HB 0.5 2.0 0.18 0.35 0.52 80 150 11.8 0.28 1100

14 310 HB 0.5 2.0 0.18 0.35 0.52 70 140 11.8 0.28 990

12 200 HB 0.5 2.5 0.22 0.40 0.65 170 250 22.2 0.32 1190

13 42 HRc 0.5 2.0 0.22 0.40 0.65 120 190 22.0 0.32 1130

15 150 HB 0.5 2.5 0.15 0.60 1.30 170 250 22.2 0.35 2200

15 200 HB 0.5 2.5 0.15 0.60 1.17 160 230 22.2 0.35 1180

16 250 HB 0.5 2.5 0.15 0.55 1.17 150 210 22.2 0.35 1160

17,19 150 HB 0.5 2.5 0.15 0.50 0.98 120 250 22.2 0.30 1180

17,19 200 HB 0.5 2.5 0.15 0.50 0.85 120 230 22.2 0.30 1160

18,20 250 HB 0.5 2.5 0.15 0.50 0.78 120 190 22.2 0.30 1140

31,32 Incoloy 800 240 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 332

33 Inconel 700 250 HB 0.5 1.5 0.20 0.35 0.46 25 45 11.5 0.28 330

34 Stellite 21 350 HB 0.5 1.5 0.20 0.35 0.46 23 40 11.5 0.28 228

36 TiAl6V4 - 0.5 2.0 0.20 0.40 0.52 45 65 11.5 0.33 555

37 T40 - 0.5 1.5 0.20 0.35 0.46 35 55 11.5 0.30 445

38 45 HRc 0.5 1.6 0.11 0.30 0.39 50 100 11.5 0.25 880

38 50 HRc 0.5 1.3 0.11 0.25 0.26 40 90 11.0 0.20 770

38 55 HRc 0.5 1.3 0.11 0.20 0.20 40 80 11.0 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.20 0.60 1.80 200 400 2.2 0.40 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



WNMP 060408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






159



1 125 HB 0.5 3.5 0.21 0.50 1.17 180 330 22.1 0.38 2240

2 190 HB 0.5 3.5 0.21 0.50 1.17 180 280 22.1 0.35 2220

3 250 HB 0.5 3.5 0.21 0.45 0.98 180 250 22.1 0.33 2200

6 180 HB 0.5 3.5 0.21 0.45 0.78 120 280 22.1 0.32 2200

4,6 230 HB 0.5 2.8 0.21 0.45 0.78 120 250 22.1 0.32 1180

5,7 280 HB 0.5 2.8 0.18 0.40 0.78 120 210 22.1 0.30 1150

8 350 HB 0.5 2.5 0.18 0.40 0.65 120 180 11.9 0.30 1130

10 220 HB 0.5 2.8 0.18 0.40 0.78 70 190 11.8 0.30 1140

10 280 HB 0.5 2.8 0.18 0.40 0.78 70 150 11.8 0.30 1120

11 320 HB 0.5 2.1 0.18 0.35 0.52 70 130 11.5 0.28 1100

11 350 HB 0.5 2.1 0.18 0.35 0.52 70 110 11.5 0.28 990

14 180 HB 0.5 3.5 0.20 0.40 0.78 170 270 22.1 0.25 1190

14 240 HB 0.5 3.5 0.20 0.40 0.65 160 220 22.1 0.22 1170

14 290 HB 0.5 2.8 0.18 0.35 0.52 80 150 11.8 0.24 1100

14 310 HB 0.5 2.8 0.18 0.35 0.52 70 140 11.8 0.24 990

12 200 HB 0.5 3.5 0.18 0.40 0.46 170 250 11.8 0.20 1190

13 42 HRc 0.5 2.8 0.18 0.40 0.46 120 190 11.5 0.20 1130

15 150 HB 0.5 3.5 0.15 0.60 1.30 170 250 22.1 0.35 2200

15 200 HB 0.5 3.5 0.15 0.60 1.17 160 230 22.1 0.35 1180

16 250 HB 0.5 3.5 0.15 0.55 1.17 150 210 22.1 0.35 1160

17,19 150 HB 0.5 3.5 0.15 0.50 0.98 120 250 22.1 0.30 1180

17,19 200 HB 0.5 3.5 0.15 0.50 0.85 120 230 22.1 0.30 1160

18,20 250 HB 0.5 3.5 0.15 0.50 0.78 120 190 22.1 0.30 1140

31,32 Incoloy 800 240 HB 0.5 2.1 0.20 0.35 0.46 25 45 11.4 0.28 330

33 Inconel 700 250 HB 0.5 2.1 0.20 0.35 0.46 25 45 11.4 0.28 330

34 Stellite 21 350 HB 0.5 2.1 0.20 0.35 0.46 25 40 11.4 0.28 330

36 TiAl6V4 - 0.5 2.5 0.20 0.40 0.52 45 65 11.4 0.33 555

37 T40 - 0.5 2.1 0.20 0.35 0.46 35 55 11.4 0.30 445

38 45 HRc 0.5 1.8 0.11 0.30 0.39 50 100 11.4 0.25 880

38 50 HRc 0.5 1.4 0.11 0.25 0.26 40 90 11.1 0.20 770

38 55 HRc 0.5 1.1 0.11 0.20 0.20 40 80 00.7 0.18 660



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.2 0.20 0.60 1.17 200 400 2.1 0.40 280

Amax [mm²]

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


St

eel


Low alloyed

D.O.C. [mm]

2



WNMP 080408 NN – LT 10 | LT 1000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






160


WNMP 080408 NN – LT 1005


1 125 HB 0.5 3.5 0.21 0.50 1.80 180 430 22.4 0.38 2265

2 190 HB 0.5 3.5 0.21 0.50 1.80 180 365 22.4 0.35 2240

3 250 HB 0.5 3.5 0.21 0.45 1.50 180 325 22.4 0.33 2220

6 180 HB 0.5 3.5 0.21 0.45 1.20 120 365 22.4 0.32 2220

4,6 230 HB 0.5 2.8 0.21 0.45 1.20 120 325 22.4 0.32 2200

5,7 280 HB 0.5 2.8 0.18 0.40 1.20 120 275 22.4 0.30 1165

8 350 HB 0.5 2.5 0.18 0.40 1.00 120 235 22.2 0.30 1145

10 220 HB 0.5 2.8 0.18 0.40 1.20 70 245 22.0 0.30 1155

10 280 HB 0.5 2.8 0.18 0.40 1.20 70 195 22.0 0.30 1130

11 320 HB 0.5 2.1 0.18 0.35 0.80 70 170 11.8 0.28 1110

11 350 HB 0.5 2.1 0.18 0.35 0.80 70 145 11.8 0.28 1100

15 150 HB 0.5 3.5 0.15 0.60 2.00 170 325 22.4 0.35 2220

15 200 HB 0.5 3.5 0.15 0.60 1.80 160 300 22.4 0.35 2200

16 250 HB 0.5 3.5 0.15 0.55 1.80 150 275 22.4 0.35 1175

17,19 150 HB 0.5 3.5 0.15 0.50 1.50 120 325 22.4 0.30 2200

17,19 200 HB 0.5 3.5 0.15 0.50 1.30 120 300 22.4 0.30 1175

18,20 250 HB 0.5 3.5 0.15 0.50 1.20 120 245 22.4 0.30 1155

38 45 HRc 0.5 1.8 0.11 0.30 0.60 50 130 11.6 0.25 990

38 50 HRc 0.5 1.4 0.11 0.25 0.40 40 115 11.2 0.20 775

38 55 HRc 0.5 1.1 0.11 0.20 0.30 40 105 00.8 0.18 665



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2






Non-alloyed

Stee

l Low alloyed

High alloyed

Cast

Iron

Grey

Malleable &Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

WNMP 080408 NN – LT 1025


1 125 HB 0.5 3.5 0.21 0.50 1.17 90 330 22.1 0.38 2240

2 190 HB 0.5 3.5 0.21 0.50 1.17 90 280 22.1 0.35 2220

3 250 HB 0.5 3.5 0.21 0.45 0.98 90 250 22.1 0.33 2200

6 180 HB 0.5 3.5 0.21 0.45 0.78 60 280 22.1 0.32 2200

4,6 230 HB 0.5 2.8 0.21 0.45 0.78 60 250 22.1 0.32 1180

5,7 280 HB 0.5 2.8 0.18 0.40 0.78 60 210 22.1 0.30 1150

8 350 HB 0.5 2.5 0.18 0.40 0.65 60 180 11.9 0.30 1130

10 220 HB 0.5 2.8 0.18 0.40 0.78 35 190 11.8 0.30 1140

10 280 HB 0.5 2.8 0.18 0.40 0.78 35 150 11.8 0.30 1120

11 320 HB 0.5 2.1 0.18 0.35 0.52 35 130 11.5 0.28 1100

11 350 HB 0.5 2.1 0.18 0.35 0.52 35 110 11.5 0.28 990

14 180 HB 0.5 3.5 0.20 0.40 0.78 85 270 22.1 0.25 1190

14 240 HB 0.5 3.5 0.20 0.40 0.65 80 220 22.1 0.22 1170

14 290 HB 0.5 2.8 0.18 0.35 0.52 40 150 11.8 0.24 1100

14 310 HB 0.5 2.8 0.18 0.35 0.52 35 140 11.8 0.24 990

12 200 HB 0.5 3.5 0.18 0.40 0.46 85 250 11.8 0.20 1190

13 42 HRc 0.5 2.8 0.18 0.40 0.46 60 190 11.5 0.20 1130

17,19 150 HB 0.5 3.5 0.15 0.50 0.98 60 250 22.1 0.30 1180

17,19 200 HB 0.5 3.5 0.15 0.50 0.85 60 230 22.1 0.30 1160

18,20 250 HB 0.5 3.5 0.15 0.50 0.78 60 190 22.1 0.30 1140

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

8GGG40, GGG70,

50005

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430






Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron Malleable

& Nodular

ALU-TURNING

161

LT 05ALU-TURNING

CNGGCCGT

ALU-TURNING

162


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


C C G T80° 7°


m

Tolerance

Ø d

d ± 0.025m ± 0.025 s ± 0.130

Fixing,Chipbreaker

s

F M R

Application Guide


LT 05

T0004163

T0004162

0.40

0.40

3.97

2.38

9

6

CCGT 09T304 ALU LT 05

CCGT 060204 ALU LT 05

ISO standard with extreme and unique positive chipbreaker geometry for aluminium turning operations. Suitable mostly for external operations but good also for internal operations, roughing and finishing.

ALU-TURNING

163

Machining Conditions

CCGT 060204 ALU – LT 05

CCGT 09T304 ALU – LT 05


Si < 4 % 60 HB 0.3 2.5 0.12 0.33 1.28 400 1200 11.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 2.5 0.10 0.29 1.02 250 600 11.5 0.23 3300

Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 2.5 0.10 0.29 1.02 150 800 11.5 0.23 2250

29 Fiber Plastics - 0.3 2.5 0.10 0.19 1.02 70 500 11.2 0.15 1150

30 Hard Rubber - 0.3 2.5 0.10 0.19 1.02 80 300 11.2 0.15 1150

- Graphite - 0.3 2.5 0.10 0.19 1.02 100 200 11.2 0.15 1150

36 Ti 1 - 0.3 1.0 0.09 0.15 0.24 35 60 00.9 0.13 445

37 TiAl 6 V4 - 0.3 1.0 0.12 0.19 0.20 28 40 00.9 0.12 335H.T.

A.

Ti based Alloys 10

NF

Al (<8%Si) 1321, 22 23,

24

Non-Metallic 15


Si < 4 % 60 HB 0.3 4.5 0.12 0.35 1.50 400 1200 22.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.5 0.10 0.30 1.20 250 600 22.5 0.23 3300


29 Fiber Plastics - 0.3 4.5 0.10 0.20 1.20 70 500 22.0 0.15 1150

30 Hard Rubber - 0.3 4.5 0.10 0.20 1.20 80 300 22.0 0.15 1150

- Graphite - 0.3 4.5 0.10 0.20 1.20 100 200 22.0 0.15 1150

36 Ti 1 - 0.3 1.8 0.09 0.16 0.28 35 60 11.5 0.13 445

37 TiAl 6 V4 - 0.3 1.8 0.12 0.20 0.24 28 40 11.5 0.12 33510

1321, 22 23,

24

15






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

164


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


C N G G80° 0°


m

Toleranced ± 0.025m ± 0.025s ± 0.13

Ø d

Fixing,Chipbreaker

ss

F M R

Application Guide


T00010190.804.7612CNGG 120408 ALU LT 05

T0001025

T0003298

0.40

0.40

4.76

3.97

12

9

CNGG 120404 ALU LT 05

CNGG 09T304 ALU LT 05

ALU-TURNING


LT 05

ALU-TURNING

165



Si < 4 % 60 HB 0.3 5.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 5.0 0.10 0.30 1.20 250 600 22.5 0.23 3300


29 Fiber Plastics - 0.3 5.0 0.10 0.20 1.20 70 500 22.0 0.15 1150

30 Hard Rubber - 0.3 5.0 0.10 0.20 1.20 80 300 22.0 0.15 1150

- Graphite - 0.3 5.0 0.10 0.20 1.20 100 200 22.0 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335Ti based Alloys 10

Al (<8%Si) 1321, 22 23,

24

Non-Metallic 15

CNGG

CNGG 09T304 ALU – LT 05

CNGG 120404 ALU – LT 05

CNGG 120408 ALU – LT 05

min max min max min max D.O.C Feed

Si < 4 % 60 HB 0.3 5.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 5.0 0.10 0.30 1.20 250 600 22.5 0.23 3300


29 Fiber Plastics - 0.3 5.0 0.10 0.20 1.20 70 500 22.0 0.15 1150

30 Hard Rubber - 0.3 5.0 0.10 0.20 1.20 80 300 22.0 0.15 1150

- Graphite - 0.3 5.0 0.10 0.20 1.20 100 200 22.0 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335

1321, 22 23,

24

15

10


Si < 4 % 60 HB 0.3 5.0 0.18 0.60 1.50 400 1200 33.0 0.32 4400

4% < Si < 8 % 100 HB 0.3 5.0 0.18 0.50 1.20 250 600 33.0 0.32 3300


29 Fiber Plastics - 0.3 5.0 0.15 0.40 1.20 70 500 33.0 0.25 1150

30 Hard Rubber - 0.3 5.0 0.15 0.40 1.20 80 300 33.0 0.25 1150

- Graphite - 0.3 5.0 0.15 0.40 1.20 100 200 33.0 0.25 1150

36 Ti 1 - 0.3 4.0 0.15 0.28 0.28 35 60 22.5 0.20 445

37 TiAl 6 V4 - 0.3 4.0 0.15 0.26 0.24 28 40 22.5 0.18 335

15

10

1321, 22 23,

24






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

166


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


D C G T7°


55°

Toleranced ± 0.025m ± 0.025s ± 0.130

l

mØ d

Fixing,Chipbreaker

s

F M R

Application Guide


T00041640.403.9711DCGT 11T304 ALU LT 05


LT 05

ALU-TURNING

167


DCGT 11T304 ALU – LT 05

DCGT


Si < 4 % 60 HB 0.3 4.5 0.12 0.35 1.50 400 1200 22.3 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.5 0.10 0.30 1.20 250 600 22.3 0.23 3300


29 Fiber Plastics - 0.3 4.5 0.10 0.20 1.20 70 500 11.8 0.15 1150

30 Hard Rubber - 0.3 4.5 0.10 0.20 1.20 80 300 11.8 0.15 1150

- Graphite - 0.3 4.5 0.10 0.20 1.20 100 200 11.8 0.15 1150

36 Ti 1 - 0.3 1.8 0.09 0.16 0.28 35 60 11.4 0.13 445

37 TiAl 6 V4 - 0.3 1.8 0.12 0.20 0.24 28 40 11.4 0.12 33510

1321, 22 23,

24

15






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

168


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


D N G G0°


55°

l

mØ d

Fixing,Chipbreaker

ss

F M R

Application Guide


T00010100.804.7611DNGG 110408 ALU LT 05

T00010260.404.7611DNGG 110404 ALU LT 05

ALU-TURNING

55°


LT 05

ALU-MILLING

169

DNGG 110404 ALU – LT 05

Cutting Conditions

DNGG


Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 1.20 250 600 22.5 0.23 3300


29 Fiber Plastics - 0.3 4.0 0.10 0.20 1.20 70 500 22.0 0.15 1150

30 Hard Rubber - 0.3 4.0 0.10 0.20 1.20 80 300 22.0 0.15 1150

- Graphite - 0.3 4.0 0.10 0.20 1.20 100 200 22.0 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335

15

10

1321, 22 23, 24

DNGG 110408 ALU – LT 05


Si < 4 % 60 HB 0.3 4.0 0.18 0.60 1.50 400 1200 22.0 0.25 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.18 0.50 1.20 250 600 22.0 0.25 3300


29 Fiber Plastics - 0.3 4.0 0.15 0.40 1.20 70 500 22.0 0.25 1150

30 Hard Rubber - 0.3 4.0 0.15 0.40 1.20 80 300 22.0 0.25 1150

- Graphite - 0.3 4.0 0.15 0.40 1.20 100 200 22.0 0.25 1150

36 Ti 1 - 0.3 3.0 0.15 0.28 0.28 35 60 22.0 0.20 445

37 TiAl 6 V4 - 0.3 3.0 0.15 0.26 0.24 28 40 22.0 0.18 335

1321, 22 23, 24

15

10






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

170


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


T N G G


60° m

Ø d0°


ss

l

F M R

Application Guide


T00011050.404.7616TNGG 160404 ALU LT 05

60°


LT 05

ALU-MILLING

171


TNGG

TNGG 160404 ALU – LT 05


Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.50 400 1200 22.5 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 1.20 250 600 22.5 0.23 3300


29 Fiber Plastics - 0.3 4.0 0.10 0.20 1.20 70 500 22.0 0.15 1150

30 Hard Rubber - 0.3 4.0 0.10 0.20 1.20 80 300 22.0 0.15 1150

- Graphite - 0.3 4.0 0.10 0.20 1.20 100 200 22.0 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.28 35 60 11.5 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.24 28 40 11.5 0.12 335

15

10

1321, 22 23,

24






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

172


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


V N G G


Clearance Angle

35° 0°

Fixing,Chipbreaker

ss

Ø d

l

m

F M R

Application Guide


T00010320.804.7616VNGG 160408 ALU LT 05

T00010060.404.7616VNGG 160404 ALU LT 05

ALU-TURNING


LT 05

ALU-TURNING

173


VNGG

VNGG 160404 ALU – LT 05


Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300


29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150

30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150

- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510

1321, 22 23,

24

15

VNGG 160408 ALU – LT 05


Si < 4 % 60 HB 0.5 6.0 0.18 0.60 1.50 400 1200 33.0 0.32 4400

4% < Si < 8 % 100 HB 0.5 6.0 0.18 0.50 1.20 250 600 33.0 0.32 3300


29 Fiber Plastics - 0.5 6.0 0.15 0.40 1.20 70 500 33.0 0.25 1150

30 Hard Rubber - 0.5 6.0 0.15 0.40 1.20 80 300 33.0 0.25 1150

- Graphite - 0.5 6.0 0.15 0.40 1.20 100 200 33.0 0.25 1150

36 Ti 1 - 0.5 3.0 0.15 0.28 0.28 35 60 11.5 0.18 445

37 TiAl 6 V4 - 0.5 3.0 0.15 0.26 0.24 28 40 11.2 0.16 335


D.O.C. [mm]Material Group Gr. N° VDI Group Material Examples* Hardness

Amax [mm²]

H.T

.A.

Ti based Alloys 10

Feed [mm/rev] Vc [m/min]

NF

Al (<8%Si) 1321, 22 23,

24

Non-Metallic 15






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-TURNING

174


fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev


fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Medium: (M)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev


Details on page 14


ToleranceClearance Angle

0°

Fixing,Chipbreaker

ssShape

80° m

l

Ø d

s ± 0.13For l = 06, d ± 0.05 m ± 0.08 For l = 08, d ± 0.08 m ± 0.13

F M R

Application Guide


T00033000.404.768WNGG 080404 ALU LT 05

T00032990.404.766WNGG 060404 ALU LT 05


LT 05

80°°

ALU-MILLING

175

WNGGWNGG

WNGG 060404 ALU – LT 05

CUTTING CONDITIONS


Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300


29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150

30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150

- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510

1321, 22 23,

24

15

WNGG 080404 ALU – LT 05


Si < 4 % 60 HB 0.3 4.0 0.12 0.35 1.20 400 1200 22.3 0.23 4400

4% < Si < 8 % 100 HB 0.3 4.0 0.10 0.30 0.96 250 600 22.3 0.23 3300


29 Fiber Plastics - 0.3 4.0 0.10 0.20 0.96 70 500 11.8 0.15 1150

30 Hard Rubber - 0.3 4.0 0.10 0.20 0.96 80 300 11.8 0.15 1150

- Graphite - 0.3 4.0 0.10 0.20 0.96 100 200 11.8 0.15 1150

36 Ti 1 - 0.3 2.0 0.09 0.16 0.22 35 60 11.4 0.13 445

37 TiAl 6 V4 - 0.3 2.0 0.12 0.20 0.19 28 40 11.4 0.12 33510

1321, 22 23,

24

15






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic






H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

176

PARTING & GROOVING

177

PARTING & GROOVING

LT 1000 | LT 10PARTING &GROOVING

PARTING

178

PARTING & GROOVING

Parting : (P)d.o.c. =

fn = 0.30 - 1.50 mm0.08 - 0.20 mm/rev

Grooving: (G)d.o.c. =

fn = 3.00 - 7.00 mm0.35 - 0.70 mm/rev

Side Turning : (ST)d.o.c. =

fn = 0.70 - 4.50 mm0.15 - 0.45 mm/rev

= Good = Acceptable

Application Guide


G C T XShape

"Dog bone"Clearance Angle Insert Type

SpecialTolerance

d ± 0.05m ± 0.16s ± 0.13

C = 7° Rake angle

P G STInsert Designation R Catalog Nr.W

LT 1000 Multi-MatTM General Usage - Premium

T0002826

T0002828

0.25

0.25

3.00

3.00

GCTX 3003 NN LT 1000

GCTX 3003 PP LT 1000

T00028250.182.00GCTX 2002 NN LT 1000

= Not recommended

PP: All-purpose chipbreaker NN: For steel and cast iron


LT 10 Multi-MatTM General Usage - Standard

T0003910

T0003921

T0003911

0.40

0.80

0.40

3.00

5.00

4.00

MGMN 300 M LT 10

MGMN 500 M LT 10

MGMN 400 M LT 10

T00039090.202.00MGMN 200 G LT 10


LT 10 Multi-MatTM General Usage - Standard

T0003933

T0003935

T0003934

0.20

0.20

0.20

3.00

5.00

4.00

WGE 3000 LT 10

WGE 5000 LT 10

WGE 4000 LT 10

T00039320.202.00WGE 2000 LT 10

Application Guide

Application Guide

Details on page 14

179

PARTING & GROOVING

LT PNG-L 12-2.0 T200116412 12 120 1.6 15 Left

LT PNG-L 16-3.0 T200116816 16 120 2.4 15 Left

LT PNG-R 12-2.0 T200116512 12 120 1.6 15 Right

LT PNG-R 16-3.0 T200116916 16 120 2.4 15 Right

LT PNG-L 16-2.0 T200116616 16 120 1.6 15 Left

LT PNG-L 20-3.0 T200117020 20 125 2.4 15 Left

LT PNG-R 16-2.0 T200116716 16 120 1.6 15 Right

LT PNG-R 20-3.0 T200117120 20 125 2.4 15 Right

LT PNG-L 20-2.0 T200148420 20 120 1.6 15 Left

LT PNG-L 25-3.0 T200119725 25 125 2.4 15 Left

LT PNG-R 20-2.0 T200148520 20 120 1.6 15 Right

LT PNG-R 25-3.0 T200119825 25 125 2.4 15 Right

LT PNG-L 25-2.0 T200148225 25 120 1.6 15 Left

LT PNG-R 25-2.0 T200148325 25 120 1.6 15 Right

Designation D1 Catalog Nr.HandD2 L W Pmax

Designation D1 Catalog Nr.HandD2 L W Pmax

Parting Tool Holders for GCTX 2002

Parting Tool Holders for GCTX 3003

Screw:

Screw:

Key:

Key:

M2001797

M2001797

M2000609

M2000609

180

PARTING & GROOVING

LT BNG-32-3 T2002751145 32

Designation Catalog Nr.L H

LT PNB-N 2020-32 T200276232 20 4819 38 120

LT PNB-N 2525-32 T200276332 25 4823 42 120

Designation Catalog Nr.H A TB C L

Blocks

Blades

L

H

L

AT H

BC

Screw:

Key:

Key:

T2002785

T2002761

T2002786


181

PARTING & GROOVING

GCTX 2002 NN – LT 1000

min max min max Feed

1 125 HB 0.05 0.17 130 220 00.11 175

2 190 HB 0.05 0.17 130 220 00.11 175

3 250 HB 0.05 0.17 130 200 00.11 165

6 180 HB 0.05 0.15 90 200 00.10 145

4,6 230 HB 0.05 0.15 90 200 00.10 145

5,7 280 HB 0.05 0.15 90 170 00.10 130

8 350 HB 0.05 0.15 90 150 00.10 120

10 220 HB 0.05 0.14 60 170 00.10 115

10 280 HB 0.05 0.14 60 150 00.10 105

11 320 HB 0.05 0.13 60 130 00.09 95

11 350 HB 0.05 0.12 60 100 00.09 80

14 180 HB 0.05 0.10 90 150 00.07 120

14 240 HB 0.05 0.10 70 140 00.07 105

14 290 HB 0.05 0.09 60 100 00.07 80

14 310 HB 0.05 0.09 60 100 00.07 80

12 200 HB 0.05 0.09 60 130 00.07 95

13 42 HRc 0.05 0.08 50 90 00.07 70

15 150 HB 0.05 0.16 130 190 00.11 160

15 200 HB 0.05 0.16 130 190 00.11 160

16 250 HB 0.05 0.16 130 190 00.11 160

17,19 150 HB 0.05 0.14 90 150 00.10 120

17,19 200 HB 0.05 0.14 90 150 00.10 120

18,20 250 HB 0.05 0.14 90 150 00.10 120

31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30

33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30

34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29

36 TiAl6V4 - 0.05 0.08 35 60 00.07 45

37 T40 - 0.05 0.08 28 40 00.07 34

38 45 HRc 0.05 0.11 50 90 00.08 70

38 50 HRc 0.05 0.10 40 70 00.08 55

38 55 HRc 0.05 0.09 30 60 00.07 45

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.05 0.08 40 60 00.07 50

White Cast Iron 41 G-X300CrMo15 55 HRc 0.05 0.08 30 50 00.07 40

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 100 300 0.08 200

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6




Vc [m/min]

min max min max min maxMaterial Group Gr. N° VDI

GroupMaterial Exemples Hardness


min max min max Feed Vc

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

182

PARTING & GROOVING Machining Conditions

GCTX 3003 NN – LT 1000


1 125 HB 0.07 0.20 130 220 00.14 175

2 190 HB 0.07 0.20 130 220 00.14 175

3 250 HB 0.07 0.20 130 200 00.14 165

6 180 HB 0.07 0.18 90 200 00.13 145

4,6 230 HB 0.07 0.18 90 200 00.13 145

5,7 280 HB 0.07 0.18 90 170 00.13 130

8 350 HB 0.07 0.18 90 150 00.13 120

10 220 HB 0.07 0.17 60 170 00.12 115

10 280 HB 0.07 0.17 60 150 00.12 105

11 320 HB 0.07 0.16 60 130 00.11 95

11 350 HB 0.07 0.14 60 100 00.11 80

14 180 HB 0.07 0.12 90 150 00.09 120

14 240 HB 0.07 0.12 70 140 00.09 105

14 290 HB 0.07 0.11 60 100 00.09 80

14 310 HB 0.07 0.11 60 100 00.09 80

12 200 HB 0.07 0.11 60 130 00.09 95

13 42 HRc 0.07 0.10 50 90 00.08 70

15 150 HB 0.07 0.19 130 190 00.13 160

15 200 HB 0.07 0.19 130 190 00.13 160

16 250 HB 0.07 0.19 130 190 00.13 160

17,19 150 HB 0.07 0.17 90 150 00.12 120

17,19 200 HB 0.07 0.17 90 150 00.12 120

18,20 250 HB 0.07 0.17 90 150 00.12 120

31,32 Incoloy 800 240 HB 0.07 0.10 25 35 00.08 30

33 Inconel 700 250 HB 0.07 0.10 25 35 00.08 30

34 Stellite 21 350 HB 0.07 0.10 23 35 00.08 29

36 TiAl6V4 - 0.07 0.10 35 60 00.08 45

37 T40 - 0.07 0.10 28 40 00.08 34

38 45 HRc 0.07 0.13 50 90 00.10 70

38 50 HRc 0.07 0.12 40 70 00.10 55

38 55 HRc 0.07 0.11 30 60 00.09 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.12 100 300 00.10 200

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C, G-

X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


183

PARTING & GROOVING

GCTX 3003 PP – LT 1000


1 125 HB 0.05 0.17 130 220 00.11 175

2 190 HB 0.05 0.17 130 220 00.11 175

3 250 HB 0.05 0.17 130 200 00.11 165

6 180 HB 0.05 0.15 90 200 00.10 145

4,6 230 HB 0.05 0.15 90 200 00.10 145

5,7 280 HB 0.05 0.15 90 170 00.10 130

8 350 HB 0.05 0.15 90 150 00.10 120

10 220 HB 0.05 0.14 60 170 00.10 115

10 280 HB 0.05 0.14 60 150 00.10 105

11 320 HB 0.05 0.13 60 130 00.09 95

11 350 HB 0.05 0.12 60 100 00.09 80

14 180 HB 0.05 0.10 90 150 00.07 120

14 240 HB 0.05 0.10 70 140 00.07 105

14 290 HB 0.05 0.09 60 100 00.07 80

14 310 HB 0.05 0.09 60 100 00.07 80

12 200 HB 0.05 0.09 60 130 00.07 95

13 42 HRc 0.05 0.08 50 90 00.07 70

15 150 HB 0.05 0.16 130 190 00.11 160

15 200 HB 0.05 0.16 130 190 00.11 160

16 250 HB 0.05 0.16 130 190 00.11 160

17,19 150 HB 0.05 0.14 90 150 00.10 120

17,19 200 HB 0.05 0.14 90 150 00.10 120

18,20 250 HB 0.05 0.14 90 150 00.10 120

31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30

33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30

34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29

36 TiAl6V4 - 0.05 0.08 35 60 00.07 45

37 T40 - 0.05 0.08 28 40 00.07 34

38 45 HRc 0.05 0.11 50 90 00.08 70

38 50 HRc 0.05 0.10 40 70 00.08 55

38 55 HRc 0.05 0.09 30 60 00.07 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 100 300 0.08 200


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

High alloyed 3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19


9


S31500


X100CrMo13, 440C,

G-X260NiCr42Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B





Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

184


MGMN 200 G – LT 10


1 125 HB 0.3 1.5 0.09 0.18 0.21 110 210 11.0 0.11 1160

2 190 HB 0.3 1.3 0.09 0.18 0.18 110 180 11.0 0.11 1150

3 250 HB 0.3 1.3 0.09 0.16 0.17 110 160 11.0 0.11 1140

6 180 HB 0.3 1.3 0.08 0.16 0.18 70 180 11.0 0.09 1130

4,6 230 HB 0.3 1.3 0.08 0.16 0.17 70 160 11.0 0.09 1120

5,7 280 HB 0.3 1.0 0.08 0.14 0.14 70 140 11.0 0.09 1110

8 350 HB 0.3 1.0 0.08 0.14 0.13 70 120 11.0 0.09 1100

10 220 HB 0.3 1.3 0.07 0.14 0.14 40 120 11.0 0.07 880

10 280 HB 0.3 1.3 0.07 0.13 0.14 40 100 11.0 0.07 770

11 320 HB 0.3 1.0 0.07 0.11 0.11 40 80 11.0 0.07 660

11 350 HB 0.3 1.0 0.07 0.11 0.09 40 70 11.0 0.07 660

14 180 HB 0.3 1.3 0.08 0.14 0.11 100 180 11.0 0.07 1140

14 240 HB 0.3 1.3 0.08 0.14 0.09 100 140 11.0 0.07 1120

14 290 HB 0.3 1.0 0.07 0.11 0.07 50 100 11.0 0.07 880

14 310 HB 0.3 1.0 0.07 0.11 0.07 40 90 11.0 0.07 770

12 200 HB 0.3 1.3 0.08 0.14 0.11 100 160 11.0 0.09 1130

13 42 HRc 0.3 1.0 0.08 0.13 0.09 70 120 11.0 0.07 1100

15 150 HB 0.3 1.5 0.06 0.16 0.22 100 160 11.0 0.11 1130

15 200 HB 0.3 1.5 0.06 0.16 0.21 100 150 11.0 0.11 1130

16 250 HB 0.3 1.5 0.06 0.16 0.21 90 140 11.0 0.11 1120

17,19 150 HB 0.3 1.3 0.06 0.14 0.17 70 160 11.0 0.09 1120

17,19 200 HB 0.3 1.3 0.06 0.14 0.14 70 150 11.0 0.09 1110

18,20 250 HB 0.3 1.3 0.06 0.14 0.14 70 120 11.0 0.09 1100

31,32 Incoloy 800 240 HB 0.3 1.0 0.07 0.12 0.09 15 33 11.0 0.07 220

33 Inconel 700 250 HB 0.3 1.0 0.07 0.12 0.09 15 33 11.0 0.07 220

34 Stellite 21 350 HB 0.3 1.0 0.07 0.12 0.09 14 29 11.0 0.07 220

36 TiAl6V4 - 0.3 1.0 0.07 0.13 0.11 27 42 11.0 0.09 330

37 T40 - 0.3 1.0 0.07 0.11 0.09 21 39 11.0 0.07 330

38 45 HRc 0.3 0.9 0.04 0.10 0.07 30 65 00.8 0.07 550

38 50 HRc 0.3 0.8 0.04 0.08 0.06 24 59 00.6 0.06 440

38 55 HRc 0.3 0.7 0.04 0.07 0.05 24 52 00.5 0.04 440



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.0 0.08 0.24 0.25 120 260 1.0 0.12 190

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500



No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9

Duplex 5


Low alloyed 2

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







185

PARTING & GROOVING

MGMN 300 M – LT 10


1 125 HB 0.5 2.4 0.11 0.23 0.42 110 210 11.5 0.13 1160

2 190 HB 0.5 2.0 0.11 0.22 0.36 110 180 11.5 0.13 1150

3 250 HB 0.5 2.0 0.11 0.20 0.34 110 160 11.5 0.13 1140

6 180 HB 0.5 2.0 0.10 0.20 0.35 70 180 11.5 0.11 1130

4,6 230 HB 0.5 2.0 0.10 0.20 0.34 70 160 11.5 0.11 1120

5,7 280 HB 0.5 1.6 0.10 0.18 0.28 70 140 11.5 0.11 1110

8 350 HB 0.5 1.6 0.10 0.18 0.25 70 120 11.5 0.11 1100

10 220 HB 0.5 2.0 0.09 0.18 0.28 40 120 11.5 0.08 880

10 280 HB 0.5 2.0 0.09 0.16 0.28 40 100 11.5 0.08 770

11 320 HB 0.5 1.6 0.09 0.14 0.22 40 80 11.5 0.08 660

11 350 HB 0.5 1.6 0.09 0.14 0.18 40 70 11.5 0.08 660

14 180 HB 0.5 2.0 0.10 0.18 0.22 100 180 11.5 0.08 1140

14 240 HB 0.5 2.0 0.10 0.18 0.18 100 140 11.5 0.08 1120

14 290 HB 0.5 1.6 0.09 0.14 0.14 50 100 11.5 0.08 880

14 310 HB 0.5 1.6 0.09 0.14 0.14 40 90 11.5 0.08 770

12 200 HB 0.5 2.0 0.10 0.18 0.22 100 160 11.5 0.11 1130

13 42 HRc 0.5 1.6 0.10 0.16 0.18 70 120 11.5 0.08 1100

15 150 HB 0.5 2.4 0.08 0.20 0.45 100 160 11.5 0.13 1130

15 200 HB 0.5 2.4 0.08 0.20 0.42 100 150 11.5 0.13 1130

16 250 HB 0.5 2.4 0.08 0.20 0.42 90 140 11.5 0.13 1120

17,19 150 HB 0.5 2.0 0.08 0.18 0.34 70 160 11.5 0.11 1120

17,19 200 HB 0.5 2.0 0.08 0.18 0.28 70 150 11.5 0.11 1110

18,20 250 HB 0.5 2.0 0.08 0.18 0.28 70 120 11.5 0.11 1100

31,32 Incoloy 800 240 HB 0.5 1.6 0.09 0.15 0.18 15 33 11.5 0.08 220

33 Inconel 700 250 HB 0.5 1.6 0.09 0.15 0.18 15 33 11.5 0.08 220

34 Stellite 21 350 HB 0.5 1.6 0.09 0.15 0.18 14 29 11.5 0.08 220

36 TiAl6V4 - 0.5 1.6 0.09 0.16 0.22 27 42 11.5 0.11 330

37 T40 - 0.5 1.6 0.09 0.14 0.18 21 39 11.5 0.08 330

38 45 HRc 0.5 1.4 0.05 0.12 0.14 30 65 11.1 0.08 550

38 50 HRc 0.5 1.2 0.05 0.10 0.12 24 59 00.9 0.06 440

38 55 HRc 0.5 1.1 0.05 0.09 0.09 24 52 00.7 0.05 440



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.2 0.10 0.30 0.49 120 260 1.5 0.14 190

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5

7 GG20, GG40, EN-GJL-250,

No30B

8

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






186


MGMN 400 M – LT 10


1 125 HB 1.0 3.6 0.13 0.28 0.60 110 210 22.5 0.22 1160

2 190 HB 1.0 3.0 0.13 0.26 0.52 110 180 22.5 0.22 1150

3 250 HB 1.0 3.0 0.13 0.24 0.48 110 160 22.5 0.22 1140

6 180 HB 1.0 3.0 0.12 0.24 0.50 70 180 22.5 0.18 1130

4,6 230 HB 1.0 3.0 0.12 0.24 0.48 70 160 22.5 0.18 1120

5,7 280 HB 1.0 2.4 0.12 0.22 0.40 70 140 22.5 0.18 1110

8 350 HB 1.0 2.4 0.12 0.22 0.36 70 120 22.5 0.18 1100

10 220 HB 1.0 3.0 0.11 0.22 0.40 40 120 22.5 0.14 880

10 280 HB 1.0 3.0 0.11 0.19 0.40 40 100 22.5 0.14 770

11 320 HB 1.0 2.4 0.11 0.17 0.32 40 80 22.5 0.14 660

11 350 HB 1.0 2.4 0.11 0.17 0.26 40 70 22.5 0.14 660

14 180 HB 1.0 3.0 0.12 0.22 0.32 100 180 22.5 0.14 1140

14 240 HB 1.0 3.0 0.12 0.22 0.26 100 140 22.5 0.14 1120

14 290 HB 1.0 2.4 0.11 0.17 0.20 50 100 22.5 0.14 880

14 310 HB 1.0 2.4 0.11 0.17 0.20 40 90 22.5 0.14 770

12 200 HB 1.0 3.0 0.12 0.22 0.32 100 160 22.5 0.18 1130

13 42 HRc 1.0 2.4 0.12 0.19 0.26 70 120 22.5 0.14 1100

15 150 HB 1.0 3.6 0.10 0.24 0.64 100 160 22.5 0.22 1130

15 200 HB 1.0 3.6 0.10 0.24 0.60 100 150 22.5 0.22 1130

16 250 HB 1.0 3.6 0.10 0.24 0.60 90 140 22.5 0.22 1120

17,19 150 HB 1.0 3.0 0.10 0.22 0.48 70 160 22.5 0.18 1120

17,19 200 HB 1.0 3.0 0.10 0.22 0.40 70 150 22.5 0.18 1110

18,20 250 HB 1.0 3.0 0.10 0.22 0.40 70 120 22.5 0.18 1100

31,32 Incoloy 800 240 HB 1.0 2.4 0.11 0.18 0.26 15 33 22.5 0.14 220

33 Inconel 700 250 HB 1.0 2.4 0.11 0.18 0.26 15 33 22.5 0.14 220

34 Stellite 21 350 HB 1.0 2.4 0.11 0.18 0.26 14 29 22.5 0.14 220

36 TiAl6V4 - 1.0 2.4 0.11 0.19 0.32 27 42 22.5 0.18 330

37 T40 - 1.0 2.4 0.11 0.17 0.26 21 39 22.5 0.14 330

38 45 HRc 1.0 2.2 0.06 0.14 0.20 30 65 11.9 0.13 550

38 50 HRc 1.0 1.8 0.06 0.12 0.17 24 59 11.5 0.11 440

38 55 HRc 1.0 1.7 0.06 0.11 0.13 24 52 11.3 0.08 440



NF Al (>8%Si) 12 25 AlSi12 130 HB 1.0 4.8 0.12 0.36 0.70 120 260 2.5 0.24 190

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5

St

eel


Low alloyed 2

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)







187

PARTING & GROOVING

MGMN 500 M – LT 10


1 125 HB 1.2 4.2 0.20 0.41 0.60 110 210 33.0 0.30 1160

2 190 HB 1.2 3.5 0.20 0.40 0.52 110 180 33.0 0.30 1150

3 250 HB 1.2 3.5 0.20 0.36 0.48 110 160 33.0 0.30 1140

6 180 HB 1.2 3.5 0.18 0.36 0.50 70 180 33.0 0.25 1130

4,6 230 HB 1.2 3.5 0.18 0.36 0.48 70 160 33.0 0.25 1120

5,7 280 HB 1.2 2.8 0.18 0.32 0.40 70 140 33.0 0.25 1110

8 350 HB 1.2 2.8 0.18 0.32 0.36 70 120 33.0 0.25 1100

10 220 HB 1.2 3.5 0.16 0.32 0.40 40 120 33.0 0.20 880

10 280 HB 1.2 3.5 0.16 0.29 0.40 40 100 33.0 0.20 770

11 320 HB 1.2 2.8 0.16 0.25 0.32 40 80 33.0 0.20 660

11 350 HB 1.2 2.8 0.16 0.25 0.26 40 70 33.0 0.20 660

14 180 HB 1.2 3.5 0.18 0.32 0.32 100 180 33.0 0.20 1140

14 240 HB 1.2 3.5 0.18 0.32 0.26 100 140 33.0 0.20 1120

14 290 HB 1.2 2.8 0.16 0.25 0.20 50 100 33.0 0.20 880

14 310 HB 1.2 2.8 0.16 0.25 0.20 40 90 33.0 0.20 770

12 200 HB 1.2 3.5 0.18 0.32 0.32 100 160 33.0 0.25 1130

13 42 HRc 1.2 2.8 0.18 0.29 0.26 70 120 33.0 0.20 1100

15 150 HB 1.2 4.2 0.14 0.36 0.64 100 160 33.0 0.30 1130

15 200 HB 1.2 4.2 0.14 0.36 0.60 100 150 33.0 0.30 1130

16 250 HB 1.2 4.2 0.14 0.36 0.60 90 140 33.0 0.30 1120

17,19 150 HB 1.2 3.5 0.14 0.32 0.48 70 160 33.0 0.25 1120

17,19 200 HB 1.2 3.5 0.14 0.32 0.40 70 150 33.0 0.25 1110

18,20 250 HB 1.2 3.5 0.14 0.32 0.40 70 120 33.0 0.25 1100

31,32 Incoloy 800 240 HB 1.2 2.8 0.16 0.27 0.26 15 33 33.0 0.20 220

33 Inconel 700 250 HB 1.2 2.8 0.16 0.27 0.26 15 33 33.0 0.20 220

34 Stellite 21 350 HB 1.2 2.8 0.16 0.27 0.26 14 29 33.0 0.20 220

36 TiAl6V4 - 1.2 2.8 0.16 0.29 0.32 27 42 33.0 0.25 330

37 T40 - 1.2 2.8 0.16 0.25 0.26 21 39 33.0 0.20 330

38 45 HRc 1.2 2.5 0.09 0.22 0.20 30 65 22.3 0.18 550

38 50 HRc 1.2 2.1 0.09 0.18 0.17 24 59 11.8 0.15 440

38 55 HRc 1.2 2.0 0.09 0.16 0.13 24 52 11.5 0.12 440



NF Al (>8%Si) 12 25 AlSi12 130 HB 1.2 5.6 0.18 0.54 0.70 120 260 3.0 0.33 190

St

eel


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6


Stai

nles

s St

eel


X5CrNi18-9

Duplex 5


No30B


X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Mat

.

Steel

11

GGG40, GGG70, 50005

High

Tem

p.Al

loys

Fe, Ni & Co based

9

Ti based 10

X2CrNiN23-4, S31500


Cast

Iron

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






188


WGE 2000 – LT 10


1 125 HB 0.04 0.12 110 215 00.09 160

2 190 HB 0.04 0.11 110 180 00.09 150

3 250 HB 0.04 0.10 110 165 00.09 140

6 180 HB 0.04 0.10 70 180 00.08 130

4,6 230 HB 0.04 0.10 70 165 00.08 120

5,7 280 HB 0.04 0.09 70 135 00.08 110

8 350 HB 0.04 0.09 70 115 00.08 100

10 220 HB 0.04 0.09 40 125 00.06 80

10 280 HB 0.04 0.08 40 100 00.06 70

11 320 HB 0.04 0.07 40 85 00.06 60

11 350 HB 0.04 0.07 40 70 00.06 60

14 180 HB 0.04 0.09 100 175 00.06 140

14 240 HB 0.04 0.09 95 145 00.06 120

14 290 HB 0.04 0.07 50 100 00.06 80

14 310 HB 0.04 0.07 40 90 00.06 70

12 200 HB 0.04 0.09 100 165 00.07 110

13 42 HRc 0.04 0.08 70 125 00.06 70

15 150 HB 0.03 0.10 100 165 00.09 130

15 200 HB 0.03 0.10 95 150 00.09 130

16 250 HB 0.03 0.10 90 135 00.09 120

17,19 150 HB 0.03 0.09 70 165 00.08 120

17,19 200 HB 0.03 0.09 70 150 00.08 110

18,20 250 HB 0.03 0.09 70 125 00.08 100

31,32 Incoloy 800 240 HB 0.04 0.08 15 35 00.06 20

33 Inconel 700 250 HB 0.04 0.08 15 35 00.06 20

34 Stellite 21 350 HB 0.04 0.08 15 30 00.06 20

36 TiAl6V4 - 0.04 0.08 25 40 00.08 30

37 T40 - 0.04 0.07 20 40 00.06 30

38 45 HRc 0.03 0.06 30 65 00.06 50

38 50 HRc 0.03 0.05 25 60 00.05 40

38 55 HRc 0.03 0.05 25 50 00.04 40



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.15 120 260 0.10 190

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)




Vc [m/min]






189

PARTING & GROOVING

WGE 3000 – LT 10


1 125 HB 0.07 0.24 110 215 00.12 160

2 190 HB 0.07 0.23 110 180 00.12 150

3 250 HB 0.07 0.21 110 165 00.12 140

6 180 HB 0.06 0.21 70 180 00.10 130

4,6 230 HB 0.06 0.21 70 165 00.10 120

5,7 280 HB 0.06 0.19 70 135 00.10 110

8 350 HB 0.06 0.19 70 115 00.10 100

10 220 HB 0.05 0.19 40 125 00.08 80

10 280 HB 0.05 0.17 40 100 00.08 70

11 320 HB 0.05 0.15 40 85 00.08 60

11 350 HB 0.05 0.15 40 70 00.08 60

14 180 HB 0.06 0.19 100 175 00.08 140

14 240 HB 0.06 0.19 95 145 00.08 120

14 290 HB 0.05 0.15 50 100 00.08 80

14 310 HB 0.05 0.15 40 90 00.08 70

12 200 HB 0.06 0.19 100 165 00.09 110

13 42 HRc 0.06 0.17 70 125 00.08 70

15 150 HB 0.05 0.21 100 165 00.12 130

15 200 HB 0.05 0.21 95 150 00.12 130

16 250 HB 0.05 0.21 90 135 00.12 120

17,19 150 HB 0.05 0.19 70 165 00.10 120

17,19 200 HB 0.05 0.19 70 150 00.10 110

18,20 250 HB 0.05 0.19 70 125 00.10 100

31,32 Incoloy 800 240 HB 0.05 0.16 15 35 00.08 20

33 Inconel 700 250 HB 0.05 0.16 15 35 00.08 20

34 Stellite 21 350 HB 0.05 0.16 15 30 00.08 20

36 TiAl6V4 - 0.05 0.17 25 40 00.10 30

37 T40 - 0.05 0.15 20 40 00.08 30

38 45 HRc 0.03 0.13 30 65 00.07 50

38 50 HRc 0.03 0.11 25 60 00.06 40

38 55 HRc 0.03 0.09 25 50 00.05 40



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.32 120 260 0.13 190

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)




Vc [m/min]





190


WGE 4000 – LT 10

min mmax min mmax Feed Vcc

1 125 HB 0.08 0.26 110 215 00.14 160

2 190 HB 0.08 0.25 110 180 00.14 150

3 250 HB 0.08 0.23 110 165 00.14 140

6 180 HB 0.07 0.23 70 180 00.12 130

4,6 230 HB 0.07 0.23 70 165 00.12 120

5,7 280 HB 0.07 0.21 70 135 00.12 110

8 350 HB 0.07 0.21 70 115 00.12 100

10 220 HB 0.06 0.21 40 125 00.10 80

10 280 HB 0.06 0.18 40 100 00.10 70

11 320 HB 0.06 0.16 40 85 00.10 60

11 350 HB 0.06 0.16 40 70 00.10 60

14 180 HB 0.07 0.21 100 175 00.10 140

14 240 HB 0.07 0.21 95 145 00.10 120

14 290 HB 0.06 0.16 50 100 00.10 80

14 310 HB 0.06 0.16 40 90 00.10 70

12 200 HB 0.07 0.21 100 165 00.11 110

13 42 HRc 0.07 0.18 70 125 00.10 70

15 150 HB 0.06 0.23 100 165 00.14 130

15 200 HB 0.06 0.23 95 150 00.14 130

16 250 HB 0.06 0.23 90 135 00.14 120

17,19 150 HB 0.06 0.21 70 165 00.12 120

17,19 200 HB 0.06 0.21 70 150 00.12 110

18,20 250 HB 0.06 0.21 70 125 00.12 100

31,32 Incoloy 800 240 HB 0.06 0.17 15 35 00.10 20

33 Inconel 700 250 HB 0.06 0.17 15 35 00.10 20

34 Stellite 21 350 HB 0.06 0.17 15 30 00.10 20

36 TiAl6V4 - 0.06 0.18 25 40 00.12 30

37 T40 - 0.06 0.16 20 40 00.10 30

38 45 HRc 0.04 0.14 30 65 00.09 50

38 50 HRc 0.04 0.12 25 60 00.07 40

38 55 HRc 0.04 0.10 25 50 00.06 40



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.35 120 260 0.16 190

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430


1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

Gr. N°VDI


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

Unlegiert

Stah

l Niedriglegiert

Hochlegiert

Edel

stah

l

Austenitisch

Duplex

Ferritisch &Martensitisch

Guss

eise

n Grau

Sphäroguss

Supe

rleg.

Fe, Ni & Co-basiert

Ti-basiert

Gehä

rtete

s M

at.

Stahl

Schalenhartguss

Weißes Guss.

NE Al (>8%Si)




Vc [m/min]

min max min max min maxMaterialgruppe Gr. N° ISO Materialbsp. Härte

fn [mm/U] Vc [m/min] EmpfohleneStartbedingungen

min max min max fn Vc

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)




Vc [m/min]






191

PARTING & GROOVING

WGE 5000 – LT 10


1 125 HB 0.08 0.30 110 215 00.16 160

2 190 HB 0.08 0.29 110 180 00.16 150

3 250 HB 0.08 0.26 110 165 00.16 140

6 180 HB 0.07 0.26 70 180 00.14 130

4,6 230 HB 0.07 0.26 70 165 00.14 120

5,7 280 HB 0.07 0.23 70 135 00.14 110

8 350 HB 0.07 0.23 70 115 00.14 100

10 220 HB 0.06 0.23 40 125 00.11 80

10 280 HB 0.06 0.21 40 100 00.11 70

11 320 HB 0.06 0.18 40 85 00.11 60

11 350 HB 0.06 0.18 40 70 00.11 60

14 180 HB 0.07 0.23 100 175 00.11 140

14 240 HB 0.07 0.23 95 145 00.11 120

14 290 HB 0.06 0.18 50 100 00.11 80

14 310 HB 0.06 0.18 40 90 00.11 70

12 200 HB 0.07 0.23 100 165 00.13 110

13 42 HRc 0.07 0.21 70 125 00.11 70

15 150 HB 0.06 0.26 100 165 00.16 130

15 200 HB 0.06 0.26 95 150 00.16 130

16 250 HB 0.06 0.26 90 135 00.16 120

17,19 150 HB 0.06 0.23 70 165 00.14 120

17,19 200 HB 0.06 0.23 70 150 00.14 110

18,20 250 HB 0.06 0.23 70 125 00.14 100

31,32 Incoloy 800 240 HB 0.06 0.20 15 35 00.11 20

33 Inconel 700 250 HB 0.06 0.20 15 35 00.11 20

34 Stellite 21 350 HB 0.06 0.20 15 30 00.11 20

36 TiAl6V4 - 0.06 0.21 25 40 00.14 30

37 T40 - 0.06 0.18 20 40 00.11 30

38 45 HRc 0.04 0.16 30 65 00.10 50

38 50 HRc 0.04 0.13 25 60 00.08 40

38 55 HRc 0.04 0.12 25 50 00.06 40



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.07 0.39 120 260 0.18 190

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)




Vc [m/min]





192

THREAD TURNING

193

THREAD TURNING

THREAD TURNING

Thread TurningThread Turning

194

THREAD TURNING

ISO 1.5 Grade16ERProfile

Partial Profile Partial Profile

Full Profile

mm tpi

Full Profile

ISO METRICUNWHITWORTHBSPTMJ

AGAGNQ

0.5-1.51.75-3.00.5-3.03.5-5.05.5-6.0

48-1614-848-87-54.5-4

NPTNPTFTRAPEZACMESTUB ACMEAM. BUTTRESSROUND (DIN 405)DIN 20400PGSAGENGWINDEUNJAPIAPI ROUNDBUT. CASINGEXTREME LINE

60°55°

2M3M

Pitch LT 10Insert sizeType ofinsert

Multitooth

V

L I.C.06

08

11

16

22

27

4.00

5.00

6.35

9.525

12.70

15.875

mm tpi0.35-6.0 72-4

Verti

cal

HERExternal right handed

HELExternal left handed

HIRInternal right handed

HILInternal left handed

Insert Ordering Code

Partial and Full Profiles

Partial Profile:

Most economical solution.

Used for wide range of pitches.

It is partial because the exterior major or internal minor diameter is not machined.

Full profile:

Cuts all thread shapes, according to the requirements.

Wide range of inserts needed in order to fit each standard and range of pitches.

Lamina threading line provides a large range of high quality standard threading inserts.

195

THREAD TURNING

Designation Catalog Nr.

Partial Profile 60°


Partial Profile 55°

EX / IN Grade

EX / IN Grade

A60 IR11 TH000001LT 10

AG55 ER16

N55 ER22

TH000022

TH000120

LT 10

LT 10

AG55 IR16

N55 IR22

TH000025

TH000121

Dimensions

L mm I.C. A B

16

22

9.525

12.70

1.2

1.7

1.7

2.5

16

22

9.525

12.70

1.2

1.7

1.7

2.5

Pitch Range

mm TPI

48 - 8

7 - 5

0.5 - 3.0

3.5 - 5.0

48 - 8

7 - 5

0.5 - 3.0

3.5 - 5.0

LT 10

LT 10

A60 IR16 TH000007LT 10

G60 ER16 TH000010LT 10

G60 IR16 TH000013LT 10

AG60 ER16 TH000016LT 10

AG60 IR16 TH000019LT 10

BA

I.C.

L

External Right

60°

Partial Profile 60° Internal Right

BA

I.C.

L

BA

I.C.

L

External Right

55°

Partial Profile 55° Internal Right

BA

I.C.

L

A60 ER16 TH000004

Pitch Range

mm TPI

0.5 - 1.5 48 - 16

0.5 - 1.5 48 - 16

1.75 - 3.0 14 - 8

1.75 - 3.0 14 - 8

0.5 - 3.0 48 - 8

0.5 - 3.0 48 - 8

0.5 - 1.5 48 - 16

Dimensions

L mm I.C. A B

0.911 6.35 0.8

0.916 9.525 0.8

1.716 9.525 1.2

1.716 9.525 1.2

1.716 9.525 1.2

1.716 9.525 1.2

0.916 9.525 0.8LT 10

196

THREAD TURNING

ISO METRIC

Internal RightExternal Right ISO Metric ISO 965-1:1999-11DIN 13: 2005-08


EX / IN Grade

Pitch

mm

Dimensions

BA

I.C.

L

60°

1/8P

1/4PB

A

I.C.

L

ISO 1.0 IR11

ISO 0.5 ER16

ISO 0.7 ER16

ISO 0.8 IR16

TH000028

TH000122

TH000124

TH000132

ISO 1.5 IR11

ISO 0.5 IR16

ISO 0.7 IR16

TH000031

TH000128

TH000130

ISO 2.0 IR11

ISO 0.6 ER16

ISO 0.75 ER16

TH000034

TH000123

TH000125

ISO 1.0 ER16

ISO 0.6 IR16

ISO 0.75 IR16

ISO 1.0 ER16

TH000037

TH000129

TH000131

TH000037

ISO 1.0 IR16 TH000040

ISO 1.25 ER16 TH000043

ISO 1.25 IR16 TH000046

ISO 1.5 ER16 TH000049

ISO 1.5 IR16 TH000052

ISO 1.75 ER16 TH000055

ISO 1.75 IR16 TH000056

ISO 2.0 ER16 TH000058

ISO 2.0 IR16 TH000061

ISO 2.5 ER16 TH000064

ISO 2.5 IR16 TH000067

ISO 3.0 ER16

ISO 3.5 ER22

ISO 4.0 IR22

TH000070

TH000126

TH000133

ISO 3.0 IR16

ISO 4.0 ER22

TH000073

TH000127

A BI.C.

6.350

9.525

9.525

9.525

6.350

9.525

9.525

6.350

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

9.525

12.70

12.70

9.525

12.70

0.7

0.6

0.6

0.6

0.8

0.6

0.6

0.8

0.6

0.6

0.7

0.6

0.6

0.7

0.7

0.8

0.8

0.8

0.8

0.9

0.9

1.0

1.0

1.1

1.1

1.2

1.6

1.6

1.2

1.6

0.7

0.4

0.4

0.6

1.0

0.4

0.6

0.9

0.4

0.6

0.7

0.6

0.6

0.7

0.7

0.9

0.9

1.0

1.0

1.2

1.2

1.3

1.3

1.5

1.5

1.5

2.3

2.3

1.5

2.3

1.00

0.50

0.70

0.80

1.50

0.50

0.70

2.00

0.60

0.75

1.00

0.60

0.75

1.00

1.00

1.25

1.25

1.50

1.50

1.75

1.75

2.00

2.00

2.50

2.50

3.00

3.50

4.00

3.00

4.00

L mm

11

16

16

16

11

16

16

11

16

16

16

16

16

16

16

16

16

16

16

16

16

16

16

16

16

16

22

22

16

22

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

LT10

197

THREAD TURNING

TRAPEZ

Internal RightISO Metric ISO 965-1:1999-11DIN 13: 2005-08

External Right


BA

I.C.

L

BA

I.C.

L

TR3.0 ER16 TH000149

TR3.0 IR16 TH000151

TR4.0 ER22 TH000150

TR4.0 IR22 TH000152

EX / IN

Pitch

3.00

3.00

4.00

4.00

mm

Dimensions

16

16

22

22

L mm

9.525

9.525

12.70

12.70

I.C.

1.3

1.3

1.7

1.7

A

1.5

1.5

1.9

1.9

B

LT10

LT10

LT10

LT10

Grade

TR NUT

TR SCREW

30°

198

THREAD TURNING

BA

I.C.

L

BA

I.C.

L

55°

R 0.137P

R 0.137P

BSW, BSF, BSP B.S.84: 1956ISO 228-1: 1994

60°

1/8P

1/4P

External Right Internal Right

UNC, UNF, UNEFANSI B1.1-1982External Right Internal Right

BA

I.C.

L

BA

I.C.

L


UN

UN 20 ER16 TH000076

UN 20 IR16 TH000079

UN 16 ER16 TH000082

UN 16 IR16 TH000085

UN 12 ER16 TH000088

UN 12 IR16 TH000091

EX / IN

Pitch

20

20

16

16

12

12

TPI

Dimensions

16

16

16

16

16

16

L mm

9.525

9.525

9.525

9.525

9.525

9.525

I.C.

0.8

0.8

0.9

0.9

1.1

1.1

A

0.9

0.9

1.1

1.1

1.4

1.4

B

LT10

LT10

LT10

LT10

LT10

LT10

Grade


WHITWORTH

W 14 ER16 TH000094

W 14 IR16 TH000097

W 19 ER16 TH000134

W 11 ER16 TH000100

W 19 IR16 TH000135

W 11 IR16 TH000103

EX / IN

Pitch

14

14

19

11

19

11

TPI

Dimensions

16

16

16

16

16

16

L mm

9.525

9.525

9.525

9.525

9.525

9.525

I.C.

1.0

1.0

0.8

1.1

0.8

1.1

A

1.2

1.2

1.0

1.5

1.0

1.5

B

LT10

LT10

LT10

LT10

LT10

LT10

Grade

199

THREAD TURNING

BA

I.C.

L

Internal Right

BA

I.C.

L

UNC, UNF, UNEFANSI B1.1-1982

30°

90° 1°47’

30°

External Right Internal Right

BA

I.C.

L

External Right

BA

I.C.

L


NPT

NPT8 ER16 TH000145

NPT8 IR16 TH000148

NPT11.5 ER16 TH000144

NPT11.5 ER16 TH000147

NPT14 ER16 TH000143

NPT14 IR16

NPT18 ER16

TH000146

TH000142

EX / IN

Pitch

8

8

11.5

11.5

14

14

18

TPI

16

16

16

16

16

16

16

L mm

Dimensions

9.525

9.525

9.525

9.525

9.525

9.525

9.525

I.C.

1.3

1.3

1.1

1.1

0.9

0.9

0.8

A

1.8

1.8

1.5

1.5

1.2

1.2

1.0

B

LT10

LT10

LT10

LT10

LT10

LT10

LT10

Grade


BSPT

BSPT14 ER16 TH000137

BSPT14 IR16 TH000140





EX / IN

Pitch

14

14

19

11

19

11

TPI

16

16

16

16

16

16

L mm

Dimensions

1.0 1.2

1.0 1.2

0.8 0.9

1.1 1.5

0.8 0.9

1.1 1.5

9.525

9.525

9.525

9.525

9.525

9.525

I.C. A B

LT10

LT10

LT10

LT10

LT10

LT10

Grade

BSW, BSF, BSP B.S.84: 1956ISO 228-1: 1994

BSPT NUT

BSPTSCREW

27.5°

90°1°47'

27.5°R 0.137P

R 0.137P

200

THREAD TURNING

HERHolder type

16Insert sizeTool length V-Vertical

L I.C.06

08

11

16

22

27

4.00

5.00

6.35

9.525

12.70

15.875

2020

External ToolholdersSquare Shank

Internal Toolholdersround shank

Shank

8101216

2520

32

H - 100

K - 125

L - 140

M - 150

R - 200

P - 170

S - 250

T - 30010121620

3225

40

HERExternal right handed

HELExternal left handed

HIRInternal right handed

HILInternal left handed

K

Tool Holder Ordering Code

201

THREAD TURNING

HER 1616 H16 TH200001ER16 16 10016 16

HER 2020 K16 TH200004ER16 20 12520 20

HER 2525 M16 TH200007ER16 25 15025 25

Designation Catalog Nr.Insert Type f lh b

External Tool Holders ER16

The holders are made for 1.5 helix angle. In case higher helix is required, it should be replaced by other shim.

h

bf

L

Accessories: On request


HIR 0010 H11 TH200010IR11 10 10 12.5 100 7.3-

HIR 0010 K11 TH200013IR11 16 10 12.5 125 25 7.3

Internal Tool Holders IR11

Internal Tool Holders IR16

Designation Catalog Nr.D D1 Dmin L L1 FInsert Type

HIR 0013 M16 TH200016IR16 16 13 16.5 150 32 10.4

HIR 0016 P16 TH200019IR16 20 16 19.5 170 40 11.6

HIR 0020 P16 TH200022IR16 20 20 23.5 170 - 13.6

HIR 0025 R16 TH200025IR16 25 25 28.5 200 - 16.3

Designation Catalog Nr.D D1 Dmin L L1 FInsert Type


L

D1

L1

FD

Dmin

The holders are made for 1.5 helix angle. In case higher helix is required, it should be replaced by other shim.

202

THREAD TURNINGMachining conditions

min max

1 125 HB 80 130

2 190 HB 70 110

3 250 HB 60 100

6 180 HB 70 110

4,6 230 HB 70 110

5,7 280 HB 60 100

8 350 HB 50 80

10 220 HB 70 110

10 280 HB 60 100

11 320 HB 50 80

11 350 HB 50 70

14 180 HB 70 110

14 240 HB 60 90

14 290 HB 60 80

14 310 HB 60 80

12 200 HB 70 90

13 42 HRc 60 80

15 150 HB 60 110

15 200 HB 70 110

16 250 HB 60 90

17,19 150 HB 60 110

17,19 200 HB 60 90

18,20 250 HB 60 90

31,32 Incoloy 800 240 HB 40 60

33 Inconel 700 250 HB 30 50

34 Stellite 21 350 HB 20 40

36 TiAl6V4 - 40 70

37 T40 - 25 50

38 45 HRc 30 50

38 50 HRc 25 50

38 55 HRc 25 40

Chilled Cast Iron 40 Ni-Hard 2 400 HB 25 40

White Cast Iron 41 G-X300CrMo15 55 HRc 25 40

NF Al (>8%Si) 12 25 AlSi12 130 HB 80 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

Passes

min max

Pitch

mm TPI



Vc [m/min]

min max

Unlegiert

Stah

l Niedriglegiert

Hochlegiert

Edel

stah

l

Austenitisch

Duplex

Ferritisch &Martensitisch

Guss

eise

n Grau

Sphäroguss

Supe

rleg.

Fe, Ni & Co-Basiert

Ti-Basiert

Gehä

rtete

s M

at.

Stahl

Schalenhartguss

Weißes Guss.

NE Al (>8%Si)

MILLING

203

Cutters

MILLING LT 30 | LT 3000

ADKT

204

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC

Application Guide MachiningRecommendations

A D K T


85° 15°

Fixing,Chipbreaker

sl

Ø dm

Helical Interpolation SurfacingSlottingShoulder Mill

M00015730.96 Right5.6315.75ADKT 1505 PDTR LT 30

Insert Designation Catalog Nr.Directions rl


M00022090.96 Right5.6315.75ADKT 1505 PDTR LT 3000



Pocket MillingPlungingRamping Down

MILLING

205

Cutters

End Mill for ADKT 1505 PDTR

Shell Mill for ADKT 1505 PDTR

Cutter Designation Catalog Nr.D zd L1 L Ap

LT 790 W-W-D025/2* M200161325 225 44 100 15 5

LT 790 W-W-D032/3* M200150332 332 50 110 15 3

LT 790 W-W-D040/4* M200161440 432 45 115 15 2.5

α Ramp°

Cutter Designation

LT 790 M-W-D040/4*

LT 790 M-W-D080/7*

LT 790 M-W-D100/8*

LT 790 M-W-D125/9*

LT 790 M-W-D050/5*

LT 790 M-W-D063/6*

Catalog Nr.

M2001615

M2001617

M2001618

M2001619

M2001504

M2001616

D

40

80

100

125

50

63

z

4

7

8

9

5

6

Ap

15

15

15

15

15

15

d

16

27

32

40

22

22

L

40

50

50

63

40

40

α Ramp°

1.4

1.1

0.8

2.5

2.2

1.8

* On request

* On request

Dd

Ap

LL1

90°

D

d

Ap

L

90°

ADKT

Screw:Key:

M2000597M2000602

Screw:

Key:

M2000597

M2000602

MILLING

206



1 125 HB 0.5 14.0 0.18 0.32 190 330 44.0 0.23 2250

2 190 HB 0.5 14.0 0.18 0.32 190 300 44.0 0.23 2220

3 250 HB 0.5 14.0 0.18 0.32 190 250 44.0 0.23 2200

6 180 HB 0.5 14.0 0.15 0.25 150 240 44.0 0.20 2200

4,6 230 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1180

5,7 280 HB 0.5 14.0 0.15 0.22 130 190 44.0 0.18 1150

8 350 HB 0.5 14.0 0.15 0.22 130 170 44.0 0.18 1140

10 220 HB 0.5 10.0 0.12 0.22 90 150 33.0 0.18 1130

10 280 HB 0.5 10.0 0.12 0.22 90 130 33.0 0.18 1120

11 320 HB 0.5 10.0 0.12 0.18 60 110 33.0 0.16 1100

11 350 HB 0.5 10.0 0.12 0.18 60 90 33.0 0.16 880

14 180 HB 0.5 14.0 0.15 0.25 190 250 44.0 0.20 2220

14 240 HB 0.5 14.0 0.12 0.22 160 210 44.0 0.20 1190

14 290 HB 0.5 10.0 0.12 0.18 70 130 33.0 0.16 1100

14 310 HB 0.5 10.0 0.12 0.18 70 120 33.0 0.16 990

12 200 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1190

13 42 HRc 0.5 10.0 0.15 0.20 90 150 33.0 0.16 1130

15 150 HB 0.5 14.0 0.18 0.32 150 240 44.0 0.23 2200

15 200 HB 0.5 14.0 0.18 0.32 150 220 44.0 0.23 1180

16 250 HB 0.5 14.0 0.18 0.32 150 190 44.0 0.23 1160

17,19 150 HB 0.5 14.0 0.15 0.28 100 200 44.0 0.20 1180

17,19 200 HB 0.5 14.0 0.15 0.28 100 180 44.0 0.20 1150

18,20 250 HB 0.5 14.0 0.15 0.28 100 150 44.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 332

33 Inconel 700 250 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330

34 Stellite 21 350 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330

36 TiAl6V4 - 0.5 10.0 0.12 0.20 40 65 33.0 0.18 555

37 T40 - 0.5 10.0 0.12 0.18 30 55 33.0 0.16 440

38 45 HRc 0.5 5.0 0.10 0.18 40 80 22.0 0.14 660

38 50 HRc 0.5 3.0 0.10 0.16 40 70 11.5 0.13 555

38 55 HRc 0.5 1.5 0.10 0.14 40 60 11.0 0.12 550

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.5 4.0 0.10 0.18 40 80 11.5 0.14 550

White Cast Iron 41 G-X300CrMo15 55 HRc 0.5 1.5 0.10 0.14 30 60 11.0 0.12 440

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 14.0 0.18 0.32 200 400 4.0 0.25 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

ADKT 1505 – LT 30 | LT 3000












D.O.C [mm] Feed [mm/tooth] Vc [m/min] Suggested Starting Parameters


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

207

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


A O M T


= Special

°

Fixing, Chipbreaker

sl

Ø dm

Helical Interpolation SurfacingSlottingShoulder Milling

M00016400.70 Right3.6211.93AOMT 123608 PETR LT 30




AOMT

M00016400.70 Right3.6211.93AOMT 123608 PETR LT 30


AOMT 123608 PETR LT 3000 M00022100.70 Right3.6211.93

Designation Catalog Nr.Directions rl

MILLING

208

Cutters

End Mill for AOMT 123608 PETR

Shell Mill for AOMT 123608 PETR


LT 720 W-W-D016/2* M200178116 216 22 85 10 12

LT 720 W-W-D020/3*

LT 720 W-W-D020/2*

LT 720 W-W-D025/4*

M2001782

M2001818

M2001819

20

20

25

3

2

4

20

20

25

25

25

25

90

90

95

10

10

10

7

7

5

LT 720 W-W-D025/3*

LT 720 W-W-D032/4*

LT 720 W-W-D032/5*

M2001783

M2001784

M2001784

25

32

32

3

4

5

25

32

32

25

25

25

95

95

95

10

10

10

5

3

3

α Ramp°

Cutter Designation

LT 720 M-W-D040/6*

LT 720 M-W-D050/7*

Catalog Nr.

M2001785

M2001821

D

40

50

z

6

7

Ap

10

10

d

22

22

L

40

40

α Ramp°

2.5

2.2

D

d

Ap

L

90°

* On request

* On request

Dd

Ap

LL1

90°

M2002181

M2000601

Screw:

Key:

M2002181

M2000601

Screw:

Key:

MILLING

209



1 125 HB 0.5 11.0 0.13 0.22 190 330 22.0 0.15 2250

2 190 HB 0.5 11.0 0.13 0.22 190 300 22.0 0.15 2220

3 250 HB 0.5 11.0 0.13 0.22 190 250 22.0 0.15 2200

6 180 HB 0.5 11.0 0.11 0.18 150 240 22.0 0.13 2200

4,6 230 HB 0.5 11.0 0.11 0.18 150 210 22.0 0.13 1180

5,7 280 HB 0.5 11.0 0.11 0.15 130 190 22.0 0.12 1150

8 350 HB 0.5 11.0 0.11 0.15 130 170 22.0 0.12 1140

10 220 HB 0.5 7.9 0.08 0.15 90 150 11.5 0.12 1130

10 280 HB 0.5 7.9 0.08 0.15 90 130 11.5 0.12 1120

11 320 HB 0.5 7.9 0.08 0.13 60 110 11.5 0.10 1100

11 350 HB 0.5 7.9 0.08 0.13 60 90 11.5 0.10 880

14 180 HB 0.5 11.0 0.11 0.18 190 250 22.0 0.13 2220

14 240 HB 0.5 11.0 0.08 0.15 160 210 22.0 0.13 1190

14 290 HB 0.5 7.9 0.08 0.13 70 130 11.5 0.10 1100

14 310 HB 0.5 7.9 0.08 0.13 70 120 11.5 0.10 990

12 200 HB 0.5 11.0 0.11 0.18 150 210 22.0 0.13 1190

13 42 HRc 0.5 7.9 0.08 0.14 90 150 11.5 0.10 1130

15 150 HB 0.5 11.0 0.13 0.22 150 240 22.0 0.15 2200

15 200 HB 0.5 11.0 0.13 0.22 150 220 22.0 0.15 1180

16 250 HB 0.5 11.0 0.13 0.22 150 190 22.0 0.15 1160

17,19 150 HB 0.5 11.0 0.11 0.20 100 200 22.0 0.13 1180

17,19 200 HB 0.5 11.0 0.11 0.20 100 180 22.0 0.13 1150

18,20 250 HB 0.5 11.0 0.11 0.20 100 150 22.0 0.13 1130

31,32 Incoloy 800 240 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 332

33 Inconel 700 250 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 330

34 Stellite 21 350 HB 0.5 7.9 0.08 0.13 25 45 11.5 0.10 330

36 TiAl6V4 - 0.5 7.9 0.08 0.14 40 65 11.5 0.12 555

37 T40 - 0.5 7.9 0.08 0.13 30 55 11.5 0.10 440

38 45 HRc 0.5 3.9 0.07 0.13 40 80 11.0 0.09 660

38 50 HRc 0.5 2.4 0.07 0.11 40 70 00.8 0.08 555

38 55 HRc 0.5 1.2 0.07 0.10 40 60 00.5 0.08 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 11.0 0.13 0.22 200 400 2.0 0.16 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

AOMT 123608 PETR – LT 30 | LT 3000


GroupMaterial

ExemplesHardness

D.O.C [mm] Feed [mm/rev] Vc [m/min]Suggested Starting

Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

210

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


A P K T11°


Fixing,Chipbreaker

sl

Ø dm

Pocket MillingPlungingHelical Interpolation

Ramping Down

Surfacing

SlottingShoulder Milling

M00000210.95 Right4.7615.30APKT 1604 PDTR LT 30

M00000220.80 Right4.7615.30APKT 1604 PDTR LT 30 (NEW)








3.20 Right4.7615.30APKT 160432 PDTR LT 30

M00018100.80 Right5.1217.48APKT 1705 PETR LT 30

M0003833

M0001569

2.40 Right4.7615.30APKT 160424 PDTR LT 30



sInsert Designation Catalog Nr.Directionrl

211

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC












M00022120.80 Right5.1217.48APKT 1705 PETR LT 3000




Pocket-MillingPlungingHelical Interpolation

Ramping Down

Surfacing

SlottingShoulder Milling

A P K T APKT

MILLING

212

Cutters

End Mill for APKT 060204**


LT 751 C-W-D012/3 M200306912 312 26 80 5.2 5

LT 751 CL-W-D016/3 M200307016 316 50 120 5.2 2.4

LT 751 C-W-D016/4 M200307116 416 32 90 5.2 2.4

LT 751 C-W-D012/3 M200306912 312 26 80 5.2 5

LT 751 C-W-D010/2 M200306610 210 16 72 5.2 7

LT 751 C-W-D020/5

LT 751 C-W-D032/8*

M2003072

M2003074

20

32

5

8

20

25

40

40

100

130

5.2

5.2

1.6

0.8

LT 751 C-W-D025/7*

LT 751 C-W-D040/10*

M2003073

M2003075

25

40

7

10

20

32

40

40

120

140

5.2

5.2

1.2

0.6

α Ramp°

* On request

Handle:

TORX+:

Adapter 0.4 Nm:

End Mill for APKT 100332/40 PDTR

* On request M2002181M2000601

Screw:Key:


LT 745 W-W-D020/3* M200158920 320 30 100 9 7

LT 745 WL-W-D016/2* M200184916 216 35 150 9 10

LT 745 WL-W-D025/4* M200185125 425 40 200 9 5

LT 745 W-W-D016/2* M200158716 216 25 100 9 10

LT 745 W-W-D025/3* M200159125 325 30 120 9 5

LT 745 W-W-D020/3* M200158920 320 30 100 9 7

LT 745 WL-W-D020/3* M200185020 320 35 150 9 7

LT 745 WL-W-D032/4* M200185232 432 40 200 9 3

LT 745 W-W-D032/5* M200184832 532 30 120 9 3

α Ramp°

Shell Mill for APKT 100332/40 PDTR

Screw:Key:

M2002181M2000601

Cutter Designation

LT 745 M-W-D040/6*

LT 745 M-W-D050/7*

Catalog Nr.

M2001580

M2001581

D

40

50

z

6

7

d

22

22

L

40

40

Ap

9

9

* On request

** Preset 0.4 Nm screwdriver included. M2002922

M2003064

M2002923

M2001640Screw:Replacement parts:

MILLING

213

Cutters

LT 741 C-W-D020/3 M200280820 320 25 100 9 7

End Mill for APKT 1003 PDTR


LT 741 CL-W-D012/1* M200281612 116 32 150 9 5

LT 741 C-W-D010/1* M200280210 110 24 80 9 5

LT 741 C-W-D014/1* M200280414 116 24 80 9 5

LT 741 CL-W-D010/1* M200281510 116 32 150 9 5

LT 741 C-W-D016/2 M200280616 216 25 100 9 12

LT 741 C-W-D012/1* M200280312 112 24 80 9 5

LT 741 CL-W-D016/2 M200281716 216 35 150 9 12

LT 741 WL-W-D032/4 M200282032 432 40 200 9

LT 741 C-W-D018/2 M200280718 220 30 85 9 12

LT 741 CL-W-D020/3 M200281820 320 40 150 9 7

LT 741 C-W-D022/3 M200280922 320 35 95 9 7

LT 741 C-W-D025/3 M200281025 325 32 120 9 5

LT 741 C-W-D025/4 M200281125 425 32 120 9 5

LT 741 CL-W-D025/4 M200281925 425 40 200 9 5

LT 741 C-W-D028/4 M200281228 425 32 120 9 2

LT 741 C-W-D030/4 M200281330 425 32 95 9 2

LT 741 W-W-D032/5 M200281432 532 32 95 9 3

3

α Ramp°

Dd

Ap

LL1

90°

Dd

Ap

LL1

90°

* On request

C W

M2002181M2000601

Screw:Key:

MILLING

214

Cutters

Screw Coupling for APKT 1003 PDTR

Cutter Designation Catalog Nr.D zd L1 Ap

LT 741 S-W-D016/2 M200296216 2M8 25 9 12

LT 741 S-W-D020/3 M200296320 3M10 30 9 7

LT 741 S-W-D025/4 M200296425 4M12 35 9 5

α Ramp°

Screw:Key:

M2002181M2000601

Dd

Ap

L1

90°

Shell Mill for APKT 1003 PDTR

Screw:Key:

M2002181M2000601

Cutter Designation

LT 741 M-W-D040/6

LT 741 M-W-D080/11*

LT 741 M-W-D050/7

LT 741 M-W-D063/8

Catalog Nr.

M2002798

M2002801

M2002799

M2002800

D

40

80

50

63

z

6

10

7

8

d

16

27

22

22

L

40

50

40

40

Ap

9

9

9

9

α Ramp°

1.4

2.5

2.2

1.8

D

d

Ap

L

90°

* On request

MILLING

215

Cutters

Dd

Ap

LL1

90°

Shell Mill for APKT 1604 PDTR

Screw:Key:

M2000597M2000602

Screw:Key:

M2000597M2000602

Cutter Designation

LT 731 M-W-D040/4

LT 731 M-W-D080/7

LT 731 M-W-D125/9

LT 731 M-W-D100/8

LT 731 M-D-D160/10*

LT 731 M-W-D050/5

LT 731 M-W-D063/6

Catalog Nr.

M2002971

M2002974

M2002976

M2002975

M2002977

M2002972

M2002973

D

40

80

125

100

160

50

63

z

4

7

9

8

10

5

6

Ap

15

15

15

15

15

15

15

d

16

27

40

32

40

22

22

L

40

50

63

50

63

40

40

α Ramp°

1.4

0.8

1.4

n / a**

2.5

2.2

1.8

D

d

Ap

L

90°

End Mill for APKT 1604 PDTR


LT 731 W-W-D032/3 M200296832 332 50 110 15 3

LT 731 WL-W-D025/2 M200296525 225 90 220 15 5

LT 731 WL-W-D040/4 M200296940 432 90 220 15 2.5

LT 731 W-W-D025/2 M200296625 225 44 100 15 5

LT 731 W-W-D040/4 M200297040 432 50 115 15 2.5

LT 731 WL-W-D032/3 M200296732 332 90 220 15 3

α Ramp°

* On request** Not available

MILLING

216

Cutters

Shell Mill for APKT 1705 PETR

Screw:Key:

M2000597M2000602

Screw:Key:

M2000597M2000602

Cutter Designation

LT 737 M-W-D040/4

LT 737 M-W-D080/7

LT 737 M-W-D125/9

LT 737 M-W-D100/7

LT 737 M-W-D160/10

LT 737 M-W-D050/5

LT 737 M-W-D063/6

Catalog Nr.

M2001838

M2001842

M2001844

M2001843

M2001845

M2001839

M2001841

D D1

40 40

80 80

125 125

100 100

160 160

50 50

63 63

z

4

7

9

7

10

5

6

Ap

16

16

16

16

16

16

16

d

16

27

40

32

40

22

22

L

40

50

63

50

63

40

40

α Ramp°

1.4

0.8

1.4

-

2.5

2.2

1.8

D

d

Ap

L

90°

End Mill for APKT 1705 PETR

Cutter Designation Catalog Nr.D zD1 d L1 L Ap

LT 737 WL-W-D032/3 M200183732 332 32 65 200 16 3

LT 737 W-W-D025/2 M200183325 225 20 32 100 16 5

LT 737 W-W-D040/4 M200183540 440 32 45 115 16 2.5

LT 737 WL-W-D025/2 M200183625 225 25 40 210 16 5

LT 737 WL-W-D040/4 M200198240 440 32 45 200 16 2.5LT 737 WL-W-D040/4 M200198240 440 32 45 200 16 2.5

LT 737 W-W-D032/3 M200183432 332 32 40 110 16 3

α Ramp°

Dd

Ap

LL1

90°

MILLING

217



1 125 HB 0.3 5.5 0.04 0.13 190 330 11.3 0.07 2250

2 190 HB 0.3 5.5 0.04 0.13 190 300 11.3 0.07 2220

3 250 HB 0.3 5.5 0.04 0.13 190 250 11.3 0.07 2200

6 180 HB 0.3 5.5 0.03 0.10 150 240 11.3 0.06 2200

4,6 230 HB 0.3 5.5 0.03 0.10 150 210 11.3 0.06 1180

5,7 280 HB 0.3 5.5 0.03 0.09 130 190 11.3 0.05 1150

8 350 HB 0.3 5.5 0.03 0.09 130 170 11.3 0.05 1140

10 220 HB 0.3 3.9 0.03 0.09 90 150 11.0 0.05 1130

10 280 HB 0.3 3.9 0.03 0.09 90 130 11.0 0.05 1120

11 320 HB 0.3 3.9 0.03 0.07 60 110 11.0 0.05 1100

11 350 HB 0.3 3.9 0.03 0.07 60 90 11.0 0.05 880

14 180 HB 0.3 5.5 0.03 0.10 190 250 11.3 0.06 2220

14 240 HB 0.3 5.5 0.03 0.09 160 210 11.3 0.06 1190

14 290 HB 0.3 3.9 0.03 0.07 70 130 11.0 0.05 1100

14 310 HB 0.3 3.9 0.03 0.07 70 120 11.0 0.05 990

12 200 HB 0.3 5.5 0.03 0.10 150 210 11.3 0.06 1190

13 42 HRc 0.3 3.9 0.03 0.08 90 150 11.0 0.05 1130

15 150 HB 0.3 5.5 0.04 0.13 150 240 11.3 0.07 2200

15 200 HB 0.3 5.5 0.04 0.13 150 220 11.3 0.07 1180

16 250 HB 0.3 5.5 0.04 0.13 150 190 11.3 0.07 1160

17,19 150 HB 0.3 5.5 0.03 0.11 100 200 11.3 0.06 1180

17,19 200 HB 0.3 5.5 0.03 0.11 100 180 11.3 0.06 1150

18,20 250 HB 0.3 5.5 0.03 0.11 100 150 11.3 0.06 1130

31,32 Incoloy 800 240 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 332

33 Inconel 700 250 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 330

34 Stellite 21 350 HB 0.3 3.9 0.03 0.07 25 45 11.0 0.05 330

36 TiAl6V4 - 0.3 3.9 0.03 0.08 40 65 11.0 0.05 555

37 T40 - 0.3 3.9 0.03 0.07 30 55 11.0 0.05 440

38 45 HRc 0.3 2.0 0.02 0.07 40 80 00.7 0.04 660

38 50 HRc 0.3 1.2 0.02 0.06 40 70 00.5 0.04 555

38 55 HRc 0.3 0.6 0.02 0.06 40 60 00.3 0.04 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 5.5 0.04 0.13 200 400 11.3 0.08 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

APKT 060204 PDTR – LT 30 | LT3000


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

218


APKT 1003 PDTR – LT 30 | LT3000


1 125 HB 0.5 9.0 0.13 0.26 190 330 22.0 0.17 2250

2 190 HB 0.5 9.0 0.13 0.26 190 300 22.0 0.17 2220

3 250 HB 0.5 9.0 0.13 0.26 190 250 22.0 0.17 2200

6 180 HB 0.5 9.0 0.11 0.21 150 240 22.0 0.15 2200

4,6 230 HB 0.5 9.0 0.11 0.21 150 210 22.0 0.15 1180

5,7 280 HB 0.5 9.0 0.11 0.18 130 190 22.0 0.13 1150

8 350 HB 0.5 9.0 0.11 0.18 130 170 22.0 0.13 1140

10 220 HB 0.5 6.4 0.08 0.18 90 150 11.5 0.13 1130

10 280 HB 0.5 6.4 0.08 0.18 90 130 11.5 0.13 1120

11 320 HB 0.5 6.4 0.08 0.15 60 110 11.5 0.12 1100

11 350 HB 0.5 6.4 0.08 0.15 60 90 11.5 0.12 880

14 180 HB 0.5 9.0 0.11 0.21 190 250 22.0 0.15 2220

14 240 HB 0.5 9.0 0.08 0.18 160 210 22.0 0.15 1190

14 290 HB 0.5 6.4 0.08 0.15 70 130 11.5 0.12 1100

14 310 HB 0.5 6.4 0.08 0.15 70 120 11.5 0.12 990

12 200 HB 0.5 9.0 0.11 0.21 150 210 22.0 0.15 1190

13 42 HRc 0.5 6.4 0.11 0.16 90 150 11.5 0.12 1130

15 150 HB 0.5 9.0 0.13 0.26 150 240 22.0 0.17 2200

15 200 HB 0.5 9.0 0.13 0.26 150 220 22.0 0.17 1180

16 250 HB 0.5 9.0 0.13 0.26 150 190 22.0 0.17 1160

17,19 150 HB 0.5 9.0 0.11 0.23 100 200 22.0 0.15 1180

17,19 200 HB 0.5 9.0 0.11 0.23 100 180 22.0 0.15 1150

18,20 250 HB 0.5 9.0 0.11 0.23 100 150 22.0 0.15 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 332

33 Inconel 700 250 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 330

34 Stellite 21 350 HB 0.5 6.4 0.08 0.15 25 45 11.5 0.12 330

36 TiAl6V4 - 0.5 6.4 0.08 0.16 40 65 11.5 0.13 555

37 T40 - 0.5 6.4 0.08 0.15 30 55 11.5 0.12 440

38 45 HRc 0.5 3.2 0.07 0.15 40 80 11.0 0.10 660

38 50 HRc 0.5 1.9 0.07 0.13 40 70 00.8 0.09 555

38 55 HRc 0.5 1.0 0.07 0.11 40 60 00.5 0.09 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.26 200 400 22.0 0.18 280


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500


X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

219



1 125 HB 0.5 9.0 0.11 0.20 190 330 22.0 0.14 2250

2 190 HB 0.5 9.0 0.11 0.20 190 300 22.0 0.14 2220

3 250 HB 0.5 9.0 0.11 0.20 190 250 22.0 0.14 2200

6 180 HB 0.5 9.0 0.09 0.16 150 240 22.0 0.12 2200

4,6 230 HB 0.5 9.0 0.09 0.16 150 210 22.0 0.12 1180

5,7 280 HB 0.5 9.0 0.09 0.14 130 190 22.0 0.11 1150

8 350 HB 0.5 9.0 0.09 0.14 130 170 22.0 0.11 1140

10 220 HB 0.5 6.4 0.07 0.14 90 150 11.5 0.11 1130

10 280 HB 0.5 6.4 0.07 0.14 90 130 11.5 0.11 1120

11 320 HB 0.5 6.4 0.07 0.11 60 110 11.5 0.10 1100

11 350 HB 0.5 6.4 0.07 0.11 60 90 11.5 0.10 880

14 180 HB 0.5 9.0 0.09 0.16 190 250 22.0 0.12 2220

14 240 HB 0.5 9.0 0.07 0.14 160 210 22.0 0.12 1190

14 290 HB 0.5 6.4 0.07 0.11 70 130 11.5 0.10 1100

14 310 HB 0.5 6.4 0.07 0.11 70 120 11.5 0.10 990

12 200 HB 0.5 9.0 0.09 0.16 150 210 22.0 0.12 1190

13 42 HRc 0.5 6.4 0.09 0.12 90 150 11.5 0.10 1130

15 150 HB 0.5 9.0 0.11 0.20 150 240 22.0 0.14 2200

15 200 HB 0.5 9.0 0.11 0.20 150 220 22.0 0.14 1180

16 250 HB 0.5 9.0 0.11 0.20 150 190 22.0 0.14 1160

17,19 150 HB 0.5 9.0 0.09 0.17 100 200 22.0 0.12 1180

17,19 200 HB 0.5 9.0 0.09 0.17 100 180 22.0 0.12 1150

18,20 250 HB 0.5 9.0 0.09 0.17 100 150 22.0 0.12 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 332

33 Inconel 700 250 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 330

34 Stellite 21 350 HB 0.5 6.4 0.07 0.11 25 45 11.5 0.10 330

36 TiAl6V4 - 0.5 6.4 0.07 0.12 40 65 11.5 0.11 555

37 T40 - 0.5 6.4 0.07 0.11 30 55 11.5 0.10 440

38 45 HRc 0.5 3.2 0.06 0.11 40 80 11.0 0.09 660

38 50 HRc 0.5 1.9 0.06 0.10 40 70 00.8 0.08 555

38 55 HRc 0.5 1.0 0.06 0.09 40 60 00.5 0.07 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.11 0.20 200 400 22.0 0.16 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

APKT 100304 PDTR – LT 30 | LT3000


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

220



1 125 HB 0.5 9.0 0.13 0.28 190 330 22.0 0.20 2250

2 190 HB 0.5 9.0 0.13 0.28 190 300 22.0 0.20 2220

3 250 HB 0.5 9.0 0.13 0.28 190 250 22.0 0.20 2200

6 180 HB 0.5 9.0 0.11 0.22 150 240 22.0 0.18 2200

4,6 230 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1180

5,7 280 HB 0.5 9.0 0.11 0.19 130 190 22.0 0.16 1150

8 350 HB 0.5 9.0 0.11 0.19 130 170 22.0 0.16 1140

10 220 HB 0.5 6.4 0.08 0.19 90 150 11.5 0.16 1130

10 280 HB 0.5 6.4 0.08 0.19 90 130 11.5 0.16 1120

11 320 HB 0.5 6.4 0.08 0.16 60 110 11.5 0.14 1100

11 350 HB 0.5 6.4 0.08 0.16 60 90 11.5 0.14 880

14 180 HB 0.5 9.0 0.11 0.22 190 250 22.0 0.18 2220

14 240 HB 0.5 9.0 0.08 0.19 160 210 22.0 0.18 1190

14 290 HB 0.5 6.4 0.08 0.16 70 130 11.5 0.14 1100

14 310 HB 0.5 6.4 0.08 0.16 70 120 11.5 0.14 990

12 200 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1190

13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.5 0.14 1130

15 150 HB 0.5 9.0 0.13 0.28 150 240 22.0 0.20 2200

15 200 HB 0.5 9.0 0.13 0.28 150 220 22.0 0.20 1180

16 250 HB 0.5 9.0 0.13 0.28 150 190 22.0 0.20 1160

17,19 150 HB 0.5 9.0 0.11 0.25 100 200 22.0 0.18 1180

17,19 200 HB 0.5 9.0 0.11 0.25 100 180 22.0 0.18 1150

18,20 250 HB 0.5 9.0 0.11 0.25 100 150 22.0 0.18 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 332

33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330

34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330

36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.5 0.16 555

37 T40 - 0.5 6.4 0.08 0.16 30 55 11.5 0.14 440

38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.0 0.12 660

38 50 HRc 0.5 1.9 0.07 0.14 40 70 00.8 0.11 555

38 55 HRc 0.5 1.0 0.07 0.12 40 60 00.5 0.11 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 22.0 0.22 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

APKT 100312 PDTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

221



1 125 HB 0.5 9.0 0.13 0.28 190 330 22.0 0.20 2250

2 190 HB 0.5 9.0 0.13 0.28 190 300 22.0 0.20 2220

3 250 HB 0.5 9.0 0.13 0.28 190 250 22.0 0.20 2200

6 180 HB 0.5 9.0 0.11 0.22 150 240 22.0 0.18 2200

4,6 230 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1180

5,7 280 HB 0.5 9.0 0.11 0.19 130 190 22.0 0.16 1150

8 350 HB 0.5 9.0 0.11 0.19 130 170 22.0 0.16 1140

10 220 HB 0.5 6.4 0.08 0.19 90 150 11.5 0.16 1130

10 280 HB 0.5 6.4 0.08 0.19 90 130 11.5 0.16 1120

11 320 HB 0.5 6.4 0.08 0.16 60 110 11.5 0.14 1100

11 350 HB 0.5 6.4 0.08 0.16 60 90 11.5 0.14 880

14 180 HB 0.5 9.0 0.11 0.22 190 250 22.0 0.18 2220

14 240 HB 0.5 9.0 0.08 0.19 160 210 22.0 0.18 1190

14 290 HB 0.5 6.4 0.08 0.16 70 130 11.5 0.14 1100

14 310 HB 0.5 6.4 0.08 0.16 70 120 11.5 0.14 990

12 200 HB 0.5 9.0 0.11 0.22 150 210 22.0 0.18 1190

13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.5 0.14 1130

15 150 HB 0.5 9.0 0.13 0.28 150 240 22.0 0.20 2200

15 200 HB 0.5 9.0 0.13 0.28 150 220 22.0 0.20 1180

16 250 HB 0.5 9.0 0.13 0.28 150 190 22.0 0.20 1160

17,19 150 HB 0.5 9.0 0.11 0.25 100 200 22.0 0.18 1180

17,19 200 HB 0.5 9.0 0.11 0.25 100 180 22.0 0.18 1150

18,20 250 HB 0.5 9.0 0.11 0.25 100 150 22.0 0.18 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 332

33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330

34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.5 0.14 330

36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.5 0.16 555

37 T40 - 0.5 6.4 0.08 0.16 30 55 11.5 0.14 440

38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.0 0.12 660

38 50 HRc 0.5 1.9 0.07 0.14 40 70 00.8 0.11 555

38 55 HRc 0.5 1.0 0.07 0.12 40 60 00.5 0.11 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 22.0 0.22 280

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500



Low alloyed 2

APKT 100316 PDTR – LT 30 | LT 3000


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

222


APKT 100332 PDTR – LT 30 | LT 3000


1 125 HB 0.5 9.0 0.13 0.28 190 330 11.0 0.29 2250

2 190 HB 0.5 9.0 0.13 0.28 190 300 11.0 0.29 2220

3 250 HB 0.5 9.0 0.13 0.28 190 250 11.0 0.29 2200

6 180 HB 0.5 9.0 0.11 0.22 150 240 11.0 0.25 2200

4,6 230 HB 0.5 9.0 0.11 0.22 150 210 11.0 0.25 1180

5,7 280 HB 0.5 9.0 0.11 0.19 130 190 11.0 0.22 1150

8 350 HB 0.5 9.0 0.11 0.19 130 170 11.0 0.22 1140

10 220 HB 0.5 6.4 0.08 0.19 90 150 11.0 0.22 1130

10 280 HB 0.5 6.4 0.08 0.19 90 130 11.0 0.22 1120

11 320 HB 0.5 6.4 0.08 0.16 60 110 11.0 0.20 1100

11 350 HB 0.5 6.4 0.08 0.16 60 90 11.0 0.20 880

14 180 HB 0.5 9.0 0.11 0.22 190 250 11.0 0.25 2220

14 240 HB 0.5 9.0 0.08 0.19 160 210 11.0 0.25 1190

14 290 HB 0.5 6.4 0.08 0.16 70 130 11.0 0.20 1100

14 310 HB 0.5 6.4 0.08 0.16 70 120 11.0 0.20 990

12 200 HB 0.5 9.0 0.11 0.22 150 210 11.0 0.25 1190

13 42 HRc 0.5 6.4 0.11 0.18 90 150 11.0 0.20 1130

15 150 HB 0.5 9.0 0.13 0.28 150 240 11.0 0.29 2200

15 200 HB 0.5 9.0 0.13 0.28 150 220 11.0 0.29 1180

16 250 HB 0.5 9.0 0.13 0.28 150 190 11.0 0.29 1160

17,19 150 HB 0.5 9.0 0.11 0.25 100 200 11.0 0.25 1180

17,19 200 HB 0.5 9.0 0.11 0.25 100 180 11.0 0.25 1150

18,20 250 HB 0.5 9.0 0.11 0.25 100 150 11.0 0.25 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 332

33 Inconel 700 250 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 330

34 Stellite 21 350 HB 0.5 6.4 0.08 0.16 25 45 11.0 0.20 330

36 TiAl6V4 - 0.5 6.4 0.08 0.18 40 65 11.0 0.22 555

37 T40 - 0.5 6.4 0.08 0.16 30 55 11.0 0.20 440

38 45 HRc 0.4 3.2 0.07 0.16 40 80 00.7 0.17 660

38 50 HRc 0.4 1.9 0.07 0.14 40 70 00.7 0.16 555

38 55 HRc 0.4 1.0 0.07 0.12 40 60 00.7 0.15 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.28 200 400 11.0 0.31 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

223


APKT 100340 PDTR – LT 30 | LT 3000


1 125 HB 0.5 9.0 0.13 0.46 190 330 11.0 0.35 2250

2 190 HB 0.5 9.0 0.13 0.46 190 300 11.0 0.35 2220

3 250 HB 0.5 9.0 0.13 0.46 190 250 11.0 0.35 2200

6 180 HB 0.5 9.0 0.11 0.36 150 240 11.0 0.30 2200

4,6 230 HB 0.5 9.0 0.11 0.36 150 210 11.0 0.30 1180

5,7 280 HB 0.5 9.0 0.11 0.32 130 190 11.0 0.27 1150

8 350 HB 0.5 9.0 0.11 0.32 130 170 11.0 0.27 1140

10 220 HB 0.5 6.4 0.08 0.32 90 150 11.0 0.27 1130

10 280 HB 0.5 6.4 0.08 0.32 90 130 11.0 0.27 1120

11 320 HB 0.5 6.4 0.08 0.26 60 110 11.0 0.24 1100

11 350 HB 0.5 6.4 0.08 0.26 60 90 11.0 0.24 880

14 180 HB 0.5 9.0 0.11 0.36 190 250 11.0 0.30 2220

14 240 HB 0.5 9.0 0.08 0.32 160 210 11.0 0.30 1190

14 290 HB 0.5 6.4 0.08 0.26 70 130 11.0 0.24 1100

14 310 HB 0.5 6.4 0.08 0.26 70 120 11.0 0.24 990

12 200 HB 0.5 9.0 0.11 0.36 150 210 11.0 0.30 1190

13 42 HRc 0.5 6.4 0.11 0.29 90 150 11.0 0.24 1130

15 150 HB 0.5 9.0 0.13 0.46 150 240 11.0 0.35 2200

15 200 HB 0.5 9.0 0.13 0.46 150 220 11.0 0.35 1180

16 250 HB 0.5 9.0 0.13 0.46 150 190 11.0 0.35 1160

17,19 150 HB 0.5 9.0 0.11 0.41 100 200 11.0 0.30 1180

17,19 200 HB 0.5 9.0 0.11 0.41 100 180 11.0 0.30 1150

18,20 250 HB 0.5 9.0 0.11 0.41 100 150 11.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 332

33 Inconel 700 250 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 330

34 Stellite 21 350 HB 0.5 6.4 0.08 0.26 25 45 11.0 0.24 330

36 TiAl6V4 - 0.5 6.4 0.08 0.29 40 65 11.0 0.27 555

37 T40 - 0.5 6.4 0.08 0.26 30 55 11.0 0.24 440

38 45 HRc 0.4 3.2 0.07 0.26 40 80 00.7 0.21 660

38 50 HRc 0.4 1.9 0.07 0.23 40 70 00.7 0.20 555

38 55 HRc 0.4 1.0 0.07 0.20 40 60 00.7 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.46 200 400 11.0 0.38 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

224



1 125 HB 0.5 15.0 0.18 0.32 190 330 44.0 0.23 2250

2 190 HB 0.5 15.0 0.18 0.32 190 300 44.0 0.23 2220

3 250 HB 0.5 15.0 0.18 0.32 190 250 44.0 0.23 2200

6 180 HB 0.5 15.0 0.15 0.25 150 240 44.0 0.20 2200

4,6 230 HB 0.5 15.0 0.15 0.25 150 210 44.0 0.20 1180

5,7 280 HB 0.5 15.0 0.15 0.22 130 190 44.0 0.18 1150

8 350 HB 0.5 15.0 0.15 0.22 130 170 44.0 0.18 1140

10 220 HB 0.5 10.7 0.12 0.22 90 150 33.0 0.18 1130

10 280 HB 0.5 10.7 0.12 0.22 90 130 33.0 0.18 1120

11 320 HB 0.5 10.7 0.12 0.18 60 110 33.0 0.16 1100

11 350 HB 0.5 10.7 0.12 0.18 60 90 33.0 0.16 880

14 180 HB 0.5 15.0 0.15 0.25 190 250 44.0 0.20 2220

14 240 HB 0.5 15.0 0.12 0.22 160 210 44.0 0.20 1190

14 290 HB 0.5 10.7 0.12 0.18 70 130 33.0 0.16 1100

14 310 HB 0.5 10.7 0.12 0.18 70 120 33.0 0.16 990

12 200 HB 0.5 15.0 0.15 0.25 150 210 44.0 0.20 1190

13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.0 0.16 1130

15 150 HB 0.5 15.0 0.18 0.32 150 240 44.0 0.23 2200

15 200 HB 0.5 15.0 0.18 0.32 150 220 44.0 0.23 1180

16 250 HB 0.5 15.0 0.18 0.32 150 190 44.0 0.23 1160

17,19 150 HB 0.5 15.0 0.15 0.28 100 200 44.0 0.20 1180

17,19 200 HB 0.5 15.0 0.15 0.28 100 180 44.0 0.20 1150

18,20 250 HB 0.5 15.0 0.15 0.28 100 150 44.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 332

33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 330

34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.0 0.16 330

36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.0 0.18 555

37 T40 - 0.5 10.7 0.12 0.18 30 55 33.0 0.16 440

38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.0 0.14 660

38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.5 0.13 555

38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.0 0.12 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 44.0 0.25 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

APKT 1604 PDTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

225


APKT 160416 PDTR – LT 30 | LT 3000


1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250

2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220

3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200

6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200

4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180

5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150

8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140

10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130

10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120

11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100

11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880

14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220

14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190

14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100

14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990

12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190

13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130

15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200

15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180

16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160

17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180

17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150

18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332

33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555

37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440

38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660

38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555

38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

226



1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250

2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220

3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200

6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200

4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180

5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150

8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140

10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130

10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120

11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100

11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880

14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220

14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190

14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100

14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990

12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190

13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130

15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200

15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180

16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160

17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180

17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150

18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332

33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555

37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440

38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660

38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555

38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

APKT 160424 PDTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

227


APKT 160432 PDTR – LT 30 | LT 3000


1 125 HB 0.5 15.0 0.18 0.32 190 330 55.0 0.23 2250

2 190 HB 0.5 15.0 0.18 0.32 190 300 55.0 0.23 2220

3 250 HB 0.5 15.0 0.18 0.32 190 250 55.0 0.23 2200

6 180 HB 0.5 15.0 0.15 0.25 150 240 55.0 0.20 2200

4,6 230 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1180

5,7 280 HB 0.5 15.0 0.15 0.22 130 190 55.0 0.18 1150

8 350 HB 0.5 15.0 0.15 0.22 130 170 55.0 0.18 1140

10 220 HB 0.5 10.7 0.12 0.22 90 150 33.8 0.18 1130

10 280 HB 0.5 10.7 0.12 0.22 90 130 33.8 0.18 1120

11 320 HB 0.5 10.7 0.12 0.18 60 110 33.8 0.16 1100

11 350 HB 0.5 10.7 0.12 0.18 60 90 33.8 0.16 880

14 180 HB 0.5 15.0 0.15 0.25 190 250 55.0 0.20 2220

14 240 HB 0.5 15.0 0.12 0.22 160 210 55.0 0.20 1190

14 290 HB 0.5 10.7 0.12 0.18 70 130 33.8 0.16 1100

14 310 HB 0.5 10.7 0.12 0.18 70 120 33.8 0.16 990

12 200 HB 0.5 15.0 0.15 0.25 150 210 55.0 0.20 1190

13 42 HRc 0.5 10.7 0.15 0.20 90 150 33.8 0.16 1130

15 150 HB 0.5 15.0 0.18 0.32 150 240 55.0 0.23 2200

15 200 HB 0.5 15.0 0.18 0.32 150 220 55.0 0.23 1180

16 250 HB 0.5 15.0 0.18 0.32 150 190 55.0 0.23 1160

17,19 150 HB 0.5 15.0 0.15 0.28 100 200 55.0 0.20 1180

17,19 200 HB 0.5 15.0 0.15 0.28 100 180 55.0 0.20 1150

18,20 250 HB 0.5 15.0 0.15 0.28 100 150 55.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 332

33 Inconel 700 250 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

34 Stellite 21 350 HB 0.5 10.7 0.12 0.18 25 45 33.8 0.16 330

36 TiAl6V4 - 0.5 10.7 0.12 0.20 40 65 33.8 0.18 555

37 T40 - 0.5 10.7 0.12 0.18 30 55 33.8 0.16 440

38 45 HRc 0.5 5.4 0.10 0.18 40 80 22.5 0.14 660

38 50 HRc 0.5 3.2 0.10 0.16 40 70 11.9 0.13 555

38 55 HRc 0.5 1.6 0.10 0.14 40 60 11.3 0.12 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.32 200 400 55.0 0.25 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

228


APKT 1705 PDTR – LT 30 | LT 3000


1 125 HB 0.5 15.0 0.18 0.40 190 330 44.0 0.28 2250

2 190 HB 0.5 15.0 0.18 0.40 190 300 44.0 0.28 2220

3 250 HB 0.5 15.0 0.18 0.40 190 250 44.0 0.28 2200

6 180 HB 0.5 15.0 0.15 0.31 150 240 44.0 0.24 2200

4,6 230 HB 0.5 15.0 0.15 0.31 150 210 44.0 0.24 1180

5,7 280 HB 0.5 15.0 0.15 0.27 130 190 44.0 0.22 1150

8 350 HB 0.5 15.0 0.15 0.27 130 170 44.0 0.22 1140

10 220 HB 0.5 10.7 0.12 0.27 90 150 33.0 0.22 1130

10 280 HB 0.5 10.7 0.12 0.27 90 130 33.0 0.22 1120

11 320 HB 0.5 10.7 0.12 0.22 60 110 33.0 0.19 1100

11 350 HB 0.5 10.7 0.12 0.22 60 90 33.0 0.19 880

14 180 HB 0.5 15.0 0.15 0.31 190 250 44.0 0.24 2220

14 240 HB 0.5 15.0 0.12 0.27 160 210 44.0 0.24 1190

14 290 HB 0.5 10.7 0.12 0.22 70 130 33.0 0.19 1100

14 310 HB 0.5 10.7 0.12 0.22 70 120 33.0 0.19 990

12 200 HB 0.5 15.0 0.15 0.31 150 210 44.0 0.24 1190

13 42 HRc 0.5 10.7 0.15 0.25 90 150 33.0 0.19 1130

15 150 HB 0.5 15.0 0.18 0.40 150 240 44.0 0.28 2200

15 200 HB 0.5 15.0 0.18 0.40 150 220 44.0 0.28 1180

16 250 HB 0.5 15.0 0.18 0.40 150 190 44.0 0.28 1160

17,19 150 HB 0.5 15.0 0.15 0.35 100 200 44.0 0.24 1180

17,19 200 HB 0.5 15.0 0.15 0.35 100 180 44.0 0.24 1150

18,20 250 HB 0.5 15.0 0.15 0.35 100 150 44.0 0.24 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 332

33 Inconel 700 250 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 330

34 Stellite 21 350 HB 0.5 10.7 0.12 0.22 25 45 33.0 0.19 330

36 TiAl6V4 - 0.5 10.7 0.12 0.25 40 65 33.0 0.22 555

37 T40 - 0.5 10.7 0.12 0.22 30 55 33.0 0.19 440

38 45 HRc 0.5 5.4 0.10 0.22 40 80 22.0 0.17 660

38 50 HRc 0.5 3.2 0.10 0.20 40 70 11.5 0.16 555

38 55 HRc 0.5 1.6 0.10 0.17 40 60 11.0 0.14 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.18 0.40 200 400 44.0 0.30 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

229

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


A P M T


11°

Fixing,Chipbreaker

sl

Ø dm

Helical Interpolation SurfacingSlottingShoulder Milling

M0002218

M0002183

M0002216

M0004161

0.70

0.66

0.70

0.40

Right

Right

Right

Right

4.82

4.82

3.52

3.38

17.11

17.01

11.45

9.94

APMT 160408 PDTR LT 3000






M0001733

M0001134

M0001133

0.70

0.66

0.70

Right

Right

Right

4.82

4.82

3.52

17.11

17.01

11.45






APMT


MILLING

230

Cutters

* On request

* On request

Screw:Key:

M2002778M2002912

Key:Screw: M2000597

M2000602

Key:Screw: M2000597

M2000602

End Mill for APMT 1135 PDTR

End Mill for APMT 1604 PDTR

Cutter Designation

Cutter Designation

Catalog Nr.

Catalog Nr.

D

D

z

z

d

d

L1

L1

L

L

Ap

Ap

LT 760 W-W-D032/3*

LT 755 WL-W-D032/4*

M2001663

M2001661

32

32

3

5

32

25

100

40

200

200

15

9

LT 755 W-W-D020/3* M200165520 320 35 120 9 7

3

3

LT 760 WL-W-D025/2*

LT 755 WL-W-D025/4*

M2001665

M2001660

25

25

2

4

25

25

70

40

200

200

15

9

5

5

LT 755 W-W-D020/3* M200165520 320 35 120 9 7

LT 760 WL-W-D040/4* M200166740 432 100 250 15

LT 755 WL-W-D016/2* M200165816 216 30 150 9 12

2.5

LT 760 W-W-D025/2* M200166225 225 50 150 15 5

LT 755 W-W-D025/4* M200165625 425 40 150 9 5

LT 760 W-W-D040/4* M200166440 432 100 200 15

LT 755 WL-W-D020/2* M200165920 220 35 150 9 7

2.5

LT 760 W-W-D032/3* M200166332 332 100 200 15 3

LT 755 WL-W-D032/4* M200166132 525 40 200 9 3

LT 760 WL-W-D032/3*

LT 755 W-W-D032/5*

M2001666

M2001657

32

32

3

5

32

25

100

40

250

150

15

9

LT 755 W-W-D016/2* M200165416 216 30 120 9 12

3

3

α Ramp°

α Ramp°

Dd

Ap

LL1

90°

Shell Mill for APMT 1604 PDTR

Bezeichnung Katalognr.D zd L1 L Ap

LT 760 M-W-D080/7* M200167080 727 - 50 15 1.4

LT 760 M-W-D100/8* M2001671100 832 - 50 15 1.1

LT 760 M-W-D050/5* M200166850 522 - 40 15 2.2

LT 760 M-W-D125/9* M2001672125 940 - 63 15 0.8

LT 760 M-W-D063/6* M200166963 622 - 40 15 1.8

α Ramp°

* On request

D

d

Ap

L

90°

MILLING

231


APMT 0903 PDTR – LT 3000


1 125 HB 0.5 8.0 0.11 0.20 190 330 22.0 0.14 2250

2 190 HB 0.5 8.0 0.11 0.20 190 300 22.0 0.14 2220

3 250 HB 0.5 8.0 0.11 0.20 190 250 22.0 0.14 2200

6 180 HB 0.5 8.0 0.09 0.16 150 240 22.0 0.12 2200

4,6 230 HB 0.5 8.0 0.09 0.16 150 210 22.0 0.12 1180

5,7 280 HB 0.5 8.0 0.09 0.14 130 190 22.0 0.11 1150

8 350 HB 0.5 8.0 0.09 0.14 130 170 22.0 0.11 1140

10 220 HB 0.5 5.7 0.07 0.14 90 150 11.5 0.11 1130

10 280 HB 0.5 5.7 0.07 0.14 90 130 11.5 0.11 1120

11 320 HB 0.5 5.7 0.07 0.11 60 110 11.5 0.10 1100

11 350 HB 0.5 5.7 0.07 0.11 60 90 11.5 0.10 880

14 180 HB 0.5 8.0 0.09 0.16 190 250 22.0 0.12 2220

14 240 HB 0.5 8.0 0.07 0.14 160 210 22.0 0.12 1190

14 290 HB 0.5 5.7 0.07 0.11 70 130 11.5 0.10 1100

14 310 HB 0.5 5.7 0.07 0.11 70 120 11.5 0.10 990

12 200 HB 0.5 8.0 0.09 0.16 150 210 22.0 0.12 1190

13 42 HRc 0.5 5.7 0.09 0.12 90 150 11.5 0.10 1130

15 150 HB 0.5 8.0 0.11 0.20 150 240 22.0 0.14 2200

15 200 HB 0.5 8.0 0.11 0.20 150 220 22.0 0.14 1180

16 250 HB 0.5 8.0 0.11 0.20 150 190 22.0 0.14 1160

17,19 150 HB 0.5 8.0 0.09 0.17 100 200 22.0 0.12 1180

17,19 200 HB 0.5 8.0 0.09 0.17 100 180 22.0 0.12 1150

18,20 250 HB 0.5 8.0 0.09 0.17 100 150 22.0 0.12 1130

31,32 Incoloy 800 240 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 332

33 Inconel 700 250 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 330

34 Stellite 21 350 HB 0.5 5.7 0.07 0.11 25 45 11.5 0.10 330

36 TiAl6V4 - 0.5 5.7 0.07 0.12 40 65 11.5 0.11 555

37 T40 - 0.5 5.7 0.07 0.11 30 55 11.5 0.10 440

38 45 HRc 0.5 2.9 0.06 0.11 40 80 11.0 0.09 660

38 50 HRc 0.5 1.7 0.06 0.10 40 70 00.8 0.08 555

38 55 HRc 0.5 1.2 0.06 0.09 40 60 00.5 0.07 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 8.0 0.11 0.20 200 400 2.0 0.16 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

232



1 125 HB 0.5 10.0 0.13 0.22 190 330 22.0 0.15 2250

2 190 HB 0.5 10.0 0.13 0.22 190 300 22.0 0.15 2220

3 250 HB 0.5 10.0 0.13 0.22 190 250 22.0 0.15 2200

6 180 HB 0.5 10.0 0.11 0.18 150 240 22.0 0.13 2200

4,6 230 HB 0.5 10.0 0.11 0.18 150 210 22.0 0.13 1180

5,7 280 HB 0.5 10.0 0.11 0.15 130 190 22.0 0.12 1150

8 350 HB 0.5 10.0 0.11 0.15 130 170 22.0 0.12 1140

10 220 HB 0.5 7.2 0.08 0.15 90 150 11.5 0.12 1130

10 280 HB 0.5 7.2 0.08 0.15 90 130 11.5 0.12 1120

11 320 HB 0.5 7.2 0.08 0.13 60 110 11.5 0.10 1100

11 350 HB 0.5 7.2 0.08 0.13 60 90 11.5 0.10 880

14 180 HB 0.5 10.0 0.11 0.18 190 250 22.0 0.13 2220

14 240 HB 0.5 10.0 0.08 0.15 160 210 22.0 0.13 1190

14 290 HB 0.5 7.2 0.08 0.13 70 130 11.5 0.10 1100

14 310 HB 0.5 7.2 0.08 0.13 70 120 11.5 0.10 990

12 200 HB 0.5 10.0 0.11 0.18 150 210 22.0 0.13 1190

13 42 HRc 0.5 7.2 0.08 0.14 90 150 11.5 0.10 1130

15 150 HB 0.5 10.0 0.13 0.22 150 240 22.0 0.15 2200

15 200 HB 0.5 10.0 0.13 0.22 150 220 22.0 0.15 1180

16 250 HB 0.5 10.0 0.13 0.22 150 190 22.0 0.15 1160

17,19 150 HB 0.5 10.0 0.11 0.20 100 200 22.0 0.13 1180

17,19 200 HB 0.5 10.0 0.11 0.20 100 180 22.0 0.13 1150

18,20 250 HB 0.5 10.0 0.11 0.20 100 150 22.0 0.13 1130

31,32 Incoloy 800 240 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 332

33 Inconel 700 250 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 330

34 Stellite 21 350 HB 0.5 7.2 0.08 0.13 25 45 11.5 0.10 330

36 TiAl6V4 - 0.5 7.2 0.08 0.14 40 65 11.5 0.12 555

37 T40 - 0.5 7.2 0.08 0.13 30 55 11.5 0.10 440

38 45 HRc 0.5 3.6 0.07 0.13 40 80 11.0 0.09 660

38 50 HRc 0.5 2.1 0.07 0.11 40 70 00.8 0.08 555

38 55 HRc 0.5 1.1 0.07 0.10 40 60 00.5 0.08 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 10.0 0.13 0.22 200 400 2.0 0.16 280


Low alloyed 2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500


X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B


APMT 1135 PDTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

233


APMT 1604 PDTR – LT 30 | LT 3000


1 125 HB 0.5 15.0 0.16 0.30 190 330 44.0 0.21 2250

2 190 HB 0.5 15.0 0.16 0.30 190 300 44.0 0.21 2220

3 250 HB 0.5 15.0 0.16 0.30 190 250 44.0 0.21 2200

6 180 HB 0.5 15.0 0.14 0.23 150 240 44.0 0.18 2200

4,6 230 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1180

5,7 280 HB 0.5 15.0 0.14 0.20 130 190 44.0 0.16 1150

8 350 HB 0.5 15.0 0.14 0.20 130 170 44.0 0.16 1140

10 220 HB 0.5 10.7 0.11 0.20 90 150 33.0 0.16 1130

10 280 HB 0.5 10.7 0.11 0.20 90 130 33.0 0.16 1120

11 320 HB 0.5 10.7 0.11 0.17 60 110 33.0 0.14 1100

11 350 HB 0.5 10.7 0.11 0.17 60 90 33.0 0.14 880

14 180 HB 0.5 15.0 0.14 0.23 190 250 44.0 0.18 2220

14 240 HB 0.5 15.0 0.11 0.20 160 210 44.0 0.18 1190

14 290 HB 0.5 10.7 0.11 0.17 70 130 33.0 0.14 1100

14 310 HB 0.5 10.7 0.11 0.17 70 120 33.0 0.14 990

12 200 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1190

13 42 HRc 0.5 10.7 0.14 0.19 90 150 33.0 0.14 1130

15 150 HB 0.5 15.0 0.16 0.30 150 240 44.0 0.21 2200

15 200 HB 0.5 15.0 0.16 0.30 150 220 44.0 0.21 1180

16 250 HB 0.5 15.0 0.16 0.30 150 190 44.0 0.21 1160

17,19 150 HB 0.5 15.0 0.14 0.26 100 200 44.0 0.18 1180

17,19 200 HB 0.5 15.0 0.14 0.26 100 180 44.0 0.18 1150

18,20 250 HB 0.5 15.0 0.14 0.26 100 150 44.0 0.18 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 332

33 Inconel 700 250 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330

34 Stellite 21 350 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330

36 TiAl6V4 - 0.5 10.7 0.11 0.19 40 65 33.0 0.16 555

37 T40 - 0.5 10.7 0.11 0.17 30 55 33.0 0.14 440

38 45 HRc 0.5 5.4 0.09 0.17 40 80 22.0 0.13 660

38 50 HRc 0.5 3.2 0.09 0.15 40 70 11.5 0.12 555

38 55 HRc 0.5 1.6 0.09 0.13 40 60 11.0 0.11 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.16 0.30 200 400 44.0 0.23 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

234



1 125 HB 0.5 15.0 0.16 0.30 190 330 44.0 0.21 2250

2 190 HB 0.5 15.0 0.16 0.30 190 300 44.0 0.21 2220

3 250 HB 0.5 15.0 0.16 0.30 190 250 44.0 0.21 2200

6 180 HB 0.5 15.0 0.14 0.23 150 240 44.0 0.18 2200

4,6 230 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1180

5,7 280 HB 0.5 15.0 0.14 0.20 130 190 44.0 0.16 1150

8 350 HB 0.5 15.0 0.14 0.20 130 170 44.0 0.16 1140

10 220 HB 0.5 10.7 0.11 0.20 90 150 33.0 0.16 1130

10 280 HB 0.5 10.7 0.11 0.20 90 130 33.0 0.16 1120

11 320 HB 0.5 10.7 0.11 0.17 60 110 33.0 0.14 1100

11 350 HB 0.5 10.7 0.11 0.17 60 90 33.0 0.14 880

14 180 HB 0.5 15.0 0.14 0.23 190 250 44.0 0.18 2220

14 240 HB 0.5 15.0 0.11 0.20 160 210 44.0 0.18 1190

14 290 HB 0.5 10.7 0.11 0.17 70 130 33.0 0.14 1100

14 310 HB 0.5 10.7 0.11 0.17 70 120 33.0 0.14 990

12 200 HB 0.5 15.0 0.14 0.23 150 210 44.0 0.18 1190

13 42 HRc 0.5 10.7 0.14 0.19 90 150 33.0 0.14 1130

15 150 HB 0.5 15.0 0.16 0.30 150 240 44.0 0.21 2200

15 200 HB 0.5 15.0 0.16 0.30 150 220 44.0 0.21 1180

16 250 HB 0.5 15.0 0.16 0.30 150 190 44.0 0.21 1160

17,19 150 HB 0.5 15.0 0.14 0.26 100 200 44.0 0.18 1180

17,19 200 HB 0.5 15.0 0.14 0.26 100 180 44.0 0.18 1150

18,20 250 HB 0.5 15.0 0.14 0.26 100 150 44.0 0.18 1130

31,32 Incoloy 800 240 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 332

33 Inconel 700 250 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330

34 Stellite 21 350 HB 0.5 10.7 0.11 0.17 25 45 33.0 0.14 330

36 TiAl6V4 - 0.5 10.7 0.11 0.19 40 65 33.0 0.16 555

37 T40 - 0.5 10.7 0.11 0.17 30 55 33.0 0.14 440

38 45 HRc 0.5 5.4 0.09 0.17 40 80 22.0 0.13 660

38 50 HRc 0.5 3.2 0.09 0.15 40 70 11.5 0.12 555

38 55 HRc 0.5 1.6 0.09 0.13 40 60 11.0 0.11 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 15.0 0.16 0.30 200 400 44.0 0.23 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

APMT 160408 PDTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

235

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


L D M T


15°

Fixing,Chipbreaker

sl

Ø dm

Shoulder Milling SurfacingSlotting

M00017720.74 Right4.7915.71LDMT 1504 PDSR LT30



LDMT

Pocket Milling

PlungingRamping Down Helical Interpolation

MILLING

236

Cutters

* On request

* On request

Key:Screw: M2001418

M2000602

End Mill for LDMT 1504 PDSR


LT 770 W-W-D032/3* M200182332 335 50 110 15 3

LT 770 WL-W-D25/2* M200182525 225 44 150 15 5

LT 770 W-W-D040/4* M200182440 432 45 115 15 2.5

LT 770 W-W-D025/2* M200182225 225 44 100 15 5

LT 770 WL-W-D32/3* M200182632 325 50 150 15 3

α Ramp°

Shell Mill for LDMT 1504 PDSR

Screw:Key:

M2001418M2000602

Cutter Designation

LT 770 M-W-D040/4*

LT 770 M-W-D080/7*

LT 770 M-W-D125/9*

LT 770 M-W-D100/8*

LT 770 M-W-D160/9*

LT 770 M-W-D050/5*

LT 770 M-W-D063/6*

Catalog Nr.

M2001827

M2001846

M2001831

M2001830

M2001832

M2001828

M2001829

D

40

80

125

100

160

50

63

z

4

7

9

8

9

5

6

Ap

15

15

15

15

15

15

15

d

16

27

40

32

40

22

22

L

40

50

63

50

63

40

40

α Ramp°

1.4

0.8

1.1

-

2.5

2.2

1.8

D

d

Ap

L

90°

Dd

Ap

L1

90°

MILLING

237


LDMT 1504 PDSR – LT 30


1 125 HB 0.5 14.0 0.18 0.32 190 330 44.0 0.23 2250

2 190 HB 0.5 14.0 0.18 0.32 190 300 44.0 0.23 2220

3 250 HB 0.5 14.0 0.18 0.32 190 250 44.0 0.23 2200

6 180 HB 0.5 14.0 0.15 0.25 150 240 44.0 0.20 2200

4,6 230 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1180

5,7 280 HB 0.5 14.0 0.15 0.22 130 190 44.0 0.18 1150

8 350 HB 0.5 14.0 0.15 0.22 130 170 44.0 0.18 1140

10 220 HB 0.5 10.0 0.12 0.22 90 150 33.0 0.18 1130

10 280 HB 0.5 10.0 0.12 0.22 90 130 33.0 0.18 1120

11 320 HB 0.5 10.0 0.12 0.18 60 110 33.0 0.16 1100

11 350 HB 0.5 10.0 0.12 0.18 60 90 33.0 0.16 880

14 180 HB 0.5 14.0 0.15 0.25 190 250 44.0 0.20 2220

14 240 HB 0.5 14.0 0.12 0.22 160 210 44.0 0.20 1190

14 290 HB 0.5 10.0 0.12 0.18 70 130 33.0 0.16 1100

14 310 HB 0.5 10.0 0.12 0.18 70 120 33.0 0.16 990

12 200 HB 0.5 14.0 0.15 0.25 150 210 44.0 0.20 1190

13 42 HRc 0.5 10.0 0.15 0.20 90 150 33.0 0.16 1130

15 150 HB 0.5 14.0 0.18 0.32 150 240 44.0 0.23 2200

15 200 HB 0.5 14.0 0.18 0.32 150 220 44.0 0.23 1180

16 250 HB 0.5 14.0 0.18 0.32 150 190 44.0 0.23 1160

17,19 150 HB 0.5 14.0 0.15 0.28 100 200 44.0 0.20 1180

17,19 200 HB 0.5 14.0 0.15 0.28 100 180 44.0 0.20 1150

18,20 250 HB 0.5 14.0 0.15 0.28 100 150 44.0 0.20 1130

31,32 Incoloy 800 240 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 332

33 Inconel 700 250 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330

34 Stellite 21 350 HB 0.5 10.0 0.12 0.18 25 45 33.0 0.16 330

36 TiAl6V4 - 0.5 10.0 0.12 0.20 40 65 33.0 0.18 555

37 T40 - 0.5 10.0 0.12 0.18 30 55 33.0 0.16 440

38 45 HRc 0.5 5.0 0.10 0.18 40 80 22.0 0.14 660

38 50 HRc 0.5 3.0 0.10 0.16 40 70 11.5 0.13 555

38 55 HRc 0.5 1.5 0.10 0.14 40 60 11.0 0.12 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 14.0 0.18 0.32 200 400 44.0 0.25 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

238

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


O D M T

Shape Clearance Angle Tolerances ± 0.13For l = 05, d ± 0.08 m ± 0.13For l = 06, d ± 0.10 m ± 0.15

15°135°

m

l

Ø d

Fixing,Chipbreaker

s

Chamfering Surfacing

MILLING

M0001104

M0000664

0.80

0.80

Right

Right

Catalog Nr.Directionr

5.56

4.76

6.58

5.08

ODMT 060508 TN LT 30

ODMT 0504 ZZTR LT 30

Insert Designation sl


M0002219

M0003399

0.80

0.80

Right

Right

5.56

4.76

6.58

5.08

ODMT 060508 TN LT 3000

ODMT 0504 ZZTR LT 3000



MILLING

239

Cutters

ODMT

Shell Mill for ODMT 060508 TN

Screw:Key:

M2002733M2000603

Cutter Designation

LT 820 M-D-D080/5*

LT 820 M-D-D063/5*

LT 820 M-D-D160/9*

LT 820 M-D-D100/6*

LT 820 M-D-D125/7*

Catalog Nr.

M2000711

M2003837

M2000714

M2000712

M2000713

D

90

63

170

110

135

z

5

5

9

6

7

Ap

3.5

3.5

3.5

3.5

3.5

D1

80

53

160

100

125

d

27

22

40

32

40

L

50

50

63

50

63

DD1

d

Ap

L

43°

* On request

MILLING

240



1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250

2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220

3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200

6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200

4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180

5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150

8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140

10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130

10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120

11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100

11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880

14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220

14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190

14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100

14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990

12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190

13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130

15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200

15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180

16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160

17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180

17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150

18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130

31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332

33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555

37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440

38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.3 0.22 660

38 50 HRc 0.4 0.8 0.12 0.26 40 70 00.9 0.21 555

38 55 HRc 0.4 0.4 0.12 0.22 40 60 00.6 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

ODMT 0504 ZZTR – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

241



1 125 HB 0.5 4.0 0.22 0.54 190 330 22.5 0.39 2250

2 190 HB 0.5 4.0 0.22 0.54 190 300 22.5 0.39 2220

3 250 HB 0.5 4.0 0.22 0.54 190 250 22.5 0.39 2200

6 180 HB 0.5 4.0 0.18 0.43 150 240 22.5 0.34 2200

4,6 230 HB 0.5 4.0 0.18 0.43 150 210 22.5 0.34 1180

5,7 280 HB 0.5 4.0 0.18 0.37 130 190 22.5 0.31 1150

8 350 HB 0.5 4.0 0.18 0.37 130 170 22.5 0.31 1140

10 220 HB 0.5 2.9 0.14 0.37 90 150 11.9 0.31 1130

10 280 HB 0.5 2.9 0.14 0.37 90 130 11.9 0.31 1120

11 320 HB 0.5 2.9 0.14 0.31 60 110 11.9 0.27 1100

11 350 HB 0.5 2.9 0.14 0.31 60 90 11.9 0.27 880

14 180 HB 0.5 4.0 0.18 0.37 190 250 22.5 0.31 2220

14 240 HB 0.5 4.0 0.14 0.34 160 210 22.5 0.31 1190

14 290 HB 0.5 2.9 0.14 0.31 70 130 11.9 0.27 1100

14 310 HB 0.5 2.9 0.14 0.31 70 120 11.9 0.27 990

12 200 HB 0.5 4.0 0.18 0.37 150 210 22.5 0.31 1190

13 42 HRc 0.5 2.9 0.18 0.34 90 150 11.9 0.27 1130

15 150 HB 0.5 4.0 0.22 0.54 150 240 22.5 0.39 2200

15 200 HB 0.5 4.0 0.22 0.54 150 220 22.5 0.39 1180

16 250 HB 0.5 4.0 0.22 0.54 150 190 22.5 0.39 1160

17,19 150 HB 0.5 4.0 0.18 0.48 100 200 22.5 0.34 1180

17,19 200 HB 0.5 4.0 0.18 0.48 100 180 22.5 0.34 1150

18,20 250 HB 0.5 4.0 0.18 0.48 100 150 22.5 0.34 1130

31,32 Incoloy 800 240 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 332

33 Inconel 700 250 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 330

34 Stellite 21 350 HB 0.5 2.9 0.14 0.31 25 45 11.9 0.27 330

36 TiAl6V4 - 0.5 2.9 0.14 0.34 40 65 11.9 0.31 555

37 T40 - 0.5 2.9 0.14 0.31 30 55 11.9 0.27 440

38 45 HRc 0.4 1.4 0.12 0.31 40 80 11.3 0.24 660

38 50 HRc 0.4 1.1 0.12 0.27 40 70 00.9 0.22 555

38 55 HRc 0.4 0.9 0.12 0.24 40 60 00.6 0.20 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.0 0.22 0.54 200 400 22.5 0.43 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

ODMT 060508 TN – LT 30 | LT 3000


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

242

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


O D M W


s

15°135°

m

l

Ø d

Fixing,Chipbreaker


M00004510.80 Right5.566.58ODMW 060508 TN LT 30



M00034000.80 Right5.566.58ODMW 060508 TN LT 3000



Shell Mill for ODMW 060508 TN

Screw:Key:

M2002733M2000603

Cutter Designation

LT 820 M-D-D080/5*

LT 820 M-D-D063/5*

LT 820 M-D-D160/9*

LT 820 M-D-D100/6*

LT 820 M-D-D125/7*

Catalog Nr.

M2000711

M2003837

M2000714

M2000712

M2000713

D

90

63

170

110

135

z

5

5

9

6

7

Ap

3.5

3.5

3.5

3.5

3.5

D1

80

53

160

100

125

d

27

22

40

32

40

L

50

50

63

50

63

* On request

MILLING

243


ODMW

ODMW 060508 TN – LT 30 | LT 3000


1 125 HB 0.5 4.0 0.22 0.58 190 330 33.0 0.41 2250

2 190 HB 0.5 4.0 0.22 0.58 190 300 33.0 0.41 2220

3 250 HB 0.5 4.0 0.22 0.58 190 250 33.0 0.41 2200

6 180 HB 0.5 4.0 0.18 0.45 150 240 33.0 0.36 2200

4,6 230 HB 0.5 4.0 0.18 0.45 150 210 33.0 0.36 1180

5,7 280 HB 0.5 4.0 0.18 0.40 130 190 33.0 0.32 1150

8 350 HB 0.5 4.0 0.18 0.40 130 170 33.0 0.32 1140

10 220 HB 0.5 2.9 0.14 0.40 90 150 22.3 0.32 1130

10 280 HB 0.5 2.9 0.14 0.40 90 130 22.3 0.32 1120

11 320 HB 0.5 2.9 0.14 0.32 60 110 22.3 0.29 1100

11 350 HB 0.5 2.9 0.14 0.32 60 90 22.3 0.29 880

15 150 HB 0.5 4.0 0.22 0.58 150 240 33.0 0.41 2200

15 200 HB 0.5 4.0 0.22 0.58 150 220 33.0 0.41 1180

16 250 HB 0.5 4.0 0.22 0.58 150 190 33.0 0.41 1160

17,19 150 HB 0.5 4.0 0.18 0.50 100 200 33.0 0.36 1180

17,19 200 HB 0.5 4.0 0.18 0.50 100 180 33.0 0.36 1150

18,20 250 HB 0.5 4.0 0.18 0.50 100 150 33.0 0.36 1130

38 45 HRc 0.4 1.4 0.12 0.32 40 80 11.1 0.25 660

38 50 HRc 0.4 1.1 0.12 0.29 40 70 00.9 0.23 555

38 55 HRc 0.4 0.9 0.12 0.25 40 60 00.7 0.22 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

244

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


O F E R


25°135°

m

l

Ø d

Fixing,Chipbreaker

s


M00000330.80 Right4.767.43OFER 070405 TN LT 30

Catalog Nr.Insert Designation Directions rl


M00034010.80 Right4.767.43OFER 070405 TN LT 3000



MILLING

245

Cutters

Shell Mill for OFER 070405 TN

Screw:Key:

M2000606M2000609

Cutter Designation

LT 880 M-W-D080/5*

LT 880 M-W-D063/4*

LT 880 M-D-D160/10*

LT 880 M-W-D100/6*

LT 880 M-W-D125/8*

Catalog Nr.

M2000510

M2000508

M2000513

M2000511

M2000512

D

90

73

170

110

135

z

5

4

10

6

8

Ap

5

5

5

5

5

D1

80

63

160

100

125

d

27

22

40

32

40

L

50

40

63

50

63

DD1

d

Ap

L

43°

* On request OFER

MILLING

246



1 125 HB 0.5 4.5 0.22 0.51 190 330 33.0 0.37 2250

2 190 HB 0.5 4.5 0.22 0.51 190 300 33.0 0.37 2220

3 250 HB 0.5 4.5 0.22 0.51 190 250 33.0 0.37 2200

6 180 HB 0.5 4.5 0.18 0.40 150 240 33.0 0.32 2200

4,6 230 HB 0.5 4.5 0.18 0.40 150 210 33.0 0.32 1180

5,7 280 HB 0.5 4.5 0.18 0.35 130 190 33.0 0.29 1150

8 350 HB 0.5 4.5 0.18 0.35 130 170 33.0 0.29 1140

10 220 HB 0.5 3.2 0.14 0.35 90 150 22.2 0.29 1130

10 280 HB 0.5 3.2 0.14 0.35 90 130 22.2 0.29 1120

11 320 HB 0.5 3.2 0.14 0.29 60 110 22.2 0.26 1100

11 350 HB 0.5 3.2 0.14 0.29 60 90 22.2 0.26 880

14 180 HB 0.5 4.5 0.18 0.35 190 250 33.0 0.29 2220

14 240 HB 0.5 4.5 0.14 0.32 160 210 33.0 0.29 1190

14 290 HB 0.5 3.2 0.14 0.29 70 130 22.2 0.26 1100

14 310 HB 0.5 3.2 0.14 0.29 70 120 22.2 0.26 990

12 200 HB 0.5 4.5 0.18 0.35 150 210 33.0 0.29 1190

13 42 HRc 0.5 3.2 0.18 0.32 90 150 22.2 0.26 1130

15 150 HB 0.5 4.5 0.22 0.51 150 240 33.0 0.37 2200

15 200 HB 0.5 4.5 0.22 0.51 150 220 33.0 0.37 1180

16 250 HB 0.5 4.5 0.22 0.51 150 190 33.0 0.37 1160

17,19 150 HB 0.5 4.5 0.18 0.45 100 200 33.0 0.32 1180

17,19 200 HB 0.5 4.5 0.18 0.45 100 180 33.0 0.32 1150

18,20 250 HB 0.5 4.5 0.18 0.45 100 150 33.0 0.32 1130

31,32 Incoloy 800 240 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 332

33 Inconel 700 250 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330

34 Stellite 21 350 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330

36 TiAl6V4 - 0.5 3.2 0.14 0.32 40 65 22.2 0.29 555

37 T40 - 0.5 3.2 0.14 0.29 30 55 22.2 0.26 440

38 45 HRc 0.4 1.6 0.12 0.29 40 80 11.5 0.22 660

38 50 HRc 0.4 1.3 0.12 0.26 40 70 11.1 0.21 555

38 55 HRc 0.4 1.0 0.12 0.22 40 60 00.7 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.5 0.22 0.51 200 400 33.0 0.40 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

OFER 070405 TN – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

247

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


O F M T


25°135°

m

l

Ø d

s

Fixing,Chipbreakers ± 0.13

For l = 05, d ± 0.08 m ± 0.13For l = 07, d ± 0.10 m ± 0.15


M0000592

M0000034

M0000591

0.50

0.80

Right

Right0.021

Right

4.76

4.76

4.00

17.97

13.30

12.70

OFMT 070405 TN LT 30

OFMT 050405 TR LT 30

OFMT 05T305 TN LT 30



M0002222

M0002220

M0002221

0.50

0.80

Neutral

0.50 Right

Neutral

4.76

4.76

4.00

7.44

5.51

5.26

OFMT 070405 TN LT 3000

OFMT 050405 TR LT 3000

OFMT 05T305 TN LT 3000



OFMT

MILLING

248

Cutters

Shell Mill for OFMT 05T305 TN

Screw:Key:

M2000597M2000602

Cutter Designation

LT 800 M-W-D040/3

LT 800 M-W-D080/6

LT 800 M-W-D125/8

LT 800 M-W-D050/4

LT 800 M-W-D063/5

LT 800 M-W-D100/7

Catalog Nr.

M2000502

M2000505

M2000507

M2000503

M2000504

M2000506

D

47

87

132

57

70

107

z

3

6

8

4

5

7

Ap

3

3

3

3

3

3

D1

40

80

125

50

63

100

d

16

27

40

22

22

32

L

40

50

63

40

40

50

D

D1

d

Ap

L

43°

Shell Mill for OFMT 050405 TR

Screw:Key:

M2000597M2000602

Cutter Designation

LT 805 M-W-D040/3*

LT 805 M-W-D080/6*

LT 805 M-W-D125/8*

LT 805 M-W-D050/4*

LT 805 M-W-D063/5*

LT 805 M-W-D100/7*

Catalog Nr.

M2001603

M2001607

M2001609

M2001604

M2001605

M2001608

D

47

87

132

57

70

107

z

3

6

8

4

5

7

Ap

3

3

3

3

3

3

D1

40

80

125

50

63

100

d

16

27

40

22

22

32

L

40

50

63

40

40

50

* On request

Shell Mill for OFMT 070405 TN

Screw:Key:

M2002733M2000603

Cutter Designation

LT 810 M-D-D100/7*

LT 810 M-D-D080/6*

LT 810 M-D-D125/8*

Catalog Nr.

M2000708

M2000707

M2000709

D

112

92

137

z

7

6

8

Ap

4.5

4.5

4.5

D1

100

80

125

d

32

27

40

L

50

50

63

* On request

MILLING

249



1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250

2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220

3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200

6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200

4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180

5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150

8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140

10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130

10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120

11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100

11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880

14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220

14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190

14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100

14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990

12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190

13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130

15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200

15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180

16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160

17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180

17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150

18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130

31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332

33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555

37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440

38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.1 0.22 660

38 50 HRc 0.4 1.0 0.12 0.26 40 70 00.9 0.21 555

38 55 HRc 0.4 0.8 0.12 0.22 40 60 00.6 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

OFMT 05T305 TN – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

250


OFMT 050405 TR – LT 30 | LT 3000


1 125 HB 0.5 3.5 0.22 0.51 190 330 22.5 0.37 2250

2 190 HB 0.5 3.5 0.22 0.51 190 300 22.5 0.37 2220

3 250 HB 0.5 3.5 0.22 0.51 190 250 22.5 0.37 2200

6 180 HB 0.5 3.5 0.18 0.40 150 240 22.5 0.32 2200

4,6 230 HB 0.5 3.5 0.18 0.40 150 210 22.5 0.32 1180

5,7 280 HB 0.5 3.5 0.18 0.35 130 190 22.5 0.29 1150

8 350 HB 0.5 3.5 0.18 0.35 130 170 22.5 0.29 1140

10 220 HB 0.5 2.5 0.14 0.35 90 150 11.9 0.29 1130

10 280 HB 0.5 2.5 0.14 0.35 90 130 11.9 0.29 1120

11 320 HB 0.5 2.5 0.14 0.29 60 110 11.9 0.26 1100

11 350 HB 0.5 2.5 0.14 0.29 60 90 11.9 0.26 880

14 180 HB 0.5 3.5 0.18 0.35 190 250 22.5 0.29 2220

14 240 HB 0.5 3.5 0.14 0.32 160 210 22.5 0.29 1190

14 290 HB 0.5 2.5 0.14 0.29 70 130 11.9 0.26 1100

14 310 HB 0.5 2.5 0.14 0.29 70 120 11.9 0.26 990

12 200 HB 0.5 3.5 0.18 0.35 150 210 22.5 0.29 1190

13 42 HRc 0.5 2.5 0.18 0.32 90 150 11.9 0.26 1130

15 150 HB 0.5 3.5 0.22 0.51 150 240 22.5 0.37 2200

15 200 HB 0.5 3.5 0.22 0.51 150 220 22.5 0.37 1180

16 250 HB 0.5 3.5 0.22 0.51 150 190 22.5 0.37 1160

17,19 150 HB 0.5 3.5 0.18 0.45 100 200 22.5 0.32 1180

17,19 200 HB 0.5 3.5 0.18 0.45 100 180 22.5 0.32 1150

18,20 250 HB 0.5 3.5 0.18 0.45 100 150 22.5 0.32 1130

31,32 Incoloy 800 240 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 332

33 Inconel 700 250 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

34 Stellite 21 350 HB 0.5 2.5 0.14 0.29 25 45 11.9 0.26 330

36 TiAl6V4 - 0.5 2.5 0.14 0.32 40 65 11.9 0.29 555

37 T40 - 0.5 2.5 0.14 0.29 30 55 11.9 0.26 440

38 45 HRc 0.4 1.3 0.12 0.29 40 80 11.1 0.22 660

38 50 HRc 0.4 1.0 0.12 0.26 40 70 00.9 0.21 555

38 55 HRc 0.4 0.8 0.12 0.22 40 60 00.6 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.5 0.22 0.51 200 400 22.5 0.40 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

251


OFMT 070405 TN – LT 30 | LT 3000


1 125 HB 0.5 4.5 0.22 0.51 190 330 33.0 0.37 2250

2 190 HB 0.5 4.5 0.22 0.51 190 300 33.0 0.37 2220

3 250 HB 0.5 4.5 0.22 0.51 190 250 33.0 0.37 2200

6 180 HB 0.5 4.5 0.18 0.40 150 240 33.0 0.32 2200

4,6 230 HB 0.5 4.5 0.18 0.40 150 210 33.0 0.32 1180

5,7 280 HB 0.5 4.5 0.18 0.35 130 190 33.0 0.29 1150

8 350 HB 0.5 4.5 0.18 0.35 130 170 33.0 0.29 1140

10 220 HB 0.5 3.2 0.14 0.35 90 150 22.2 0.29 1130

10 280 HB 0.5 3.2 0.14 0.35 90 130 22.2 0.29 1120

11 320 HB 0.5 3.2 0.14 0.29 60 110 22.2 0.26 1100

11 350 HB 0.5 3.2 0.14 0.29 60 90 22.2 0.26 880

14 180 HB 0.5 4.5 0.18 0.35 190 250 33.0 0.29 2220

14 240 HB 0.5 4.5 0.14 0.32 160 210 33.0 0.29 1190

14 290 HB 0.5 3.2 0.14 0.29 70 130 22.2 0.26 1100

14 310 HB 0.5 3.2 0.14 0.29 70 120 22.2 0.26 990

12 200 HB 0.5 4.5 0.18 0.35 150 210 33.0 0.29 1190

13 42 HRc 0.5 3.2 0.18 0.32 90 150 22.2 0.26 1130

15 150 HB 0.5 4.5 0.22 0.51 150 240 33.0 0.37 2200

15 200 HB 0.5 4.5 0.22 0.51 150 220 33.0 0.37 1180

16 250 HB 0.5 4.5 0.22 0.51 150 190 33.0 0.37 1160

17,19 150 HB 0.5 4.5 0.18 0.45 100 200 33.0 0.32 1180

17,19 200 HB 0.5 4.5 0.18 0.45 100 180 33.0 0.32 1150

18,20 250 HB 0.5 4.5 0.18 0.45 100 150 33.0 0.32 1130

31,32 Incoloy 800 240 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 332

33 Inconel 700 250 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330

34 Stellite 21 350 HB 0.5 3.2 0.14 0.29 25 45 22.2 0.26 330

36 TiAl6V4 - 0.5 3.2 0.14 0.32 40 65 22.2 0.29 555

37 T40 - 0.5 3.2 0.14 0.29 30 55 22.2 0.26 440

38 45 HRc 0.4 1.6 0.12 0.29 40 80 11.3 0.22 660

38 50 HRc 0.4 1.3 0.12 0.26 40 70 00.9 0.21 555

38 55 HRc 0.4 1.0 0.12 0.22 40 60 00.7 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.5 0.22 0.51 200 400 33.0 0.40 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

252

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


0°


Shape

135°

Tolerance

m

l

Ø d

s

s ± 0.13For l = 05, d ± 0.08 m ± 0.13For l = 07, d ± 0.10 m ± 0.15

s


M00022110.80 Neutral5.808.36ONKX 0806-45 LT 3000



MILLING

MILLING

253

Cutters

Shell Mill for ONKX 0806-45°

Screw:Key:

M2000599M2000603

Cutter Designation

LT 987 M-W-D080/6

LT 987 M-D-D160/10 1

LT 987 M-D-D250/14* 1

LT 987 M-W-D063/5

LT 987 M-W-D125/8

LT 987 M-W-D100/7

LT 987 M-D-D200/12* 1

Catalog Nr.

M2003632

M2003635

M2003637

M2003631

M2003634

M2003633

M2003636

D

92.7

172.7

262.7

75.7

137.7

112.7

212.7

z

6

10

14

5

8

7

12

Ap

5

5

5

5

5

5

5

D1

80

160

250

63

125

100

200

d

27

40

60

22

40

32

60

L

50

63

63

50

63

50

63

DD1

d

Ap

L

43°

* On requestONKX

1 Accessories available for coolant:M2003635: M2004024M2003636: M2001847M2003637: M2001847

MILLING

254



1 125 HB 0.5 4.0 0.16 0.58 190 330 33.0 0.46 2250

2 190 HB 0.5 4.0 0.16 0.58 190 300 33.0 0.46 2220

3 250 HB 0.5 4.0 0.16 0.58 190 250 33.0 0.46 2200

6 180 HB 0.5 4.0 0.14 0.50 150 240 33.0 0.40 2200

4,6 230 HB 0.5 4.0 0.14 0.50 150 210 33.0 0.40 1180

5,7 280 HB 0.5 4.0 0.14 0.44 130 190 33.0 0.36 1150

8 350 HB 0.5 4.0 0.14 0.44 130 170 33.0 0.36 1140

10 220 HB 0.5 4.0 0.11 0.44 90 150 33.0 0.36 1130

10 280 HB 0.5 4.0 0.11 0.44 90 130 33.0 0.36 1120

11 320 HB 0.5 4.0 0.11 0.36 60 110 33.0 0.32 1100

11 350 HB 0.5 4.0 0.11 0.36 60 90 33.0 0.32 880

14 180 HB 0.5 1.5 0.14 0.44 190 250 11.2 0.34 2220

14 240 HB 0.5 1.5 0.11 0.40 160 210 11.2 0.34 1190

14 290 HB 0.5 1.5 0.11 0.36 70 130 11.2 0.30 1100

14 310 HB 0.5 1.5 0.11 0.36 70 120 11.2 0.30 990

12 200 HB 0.5 1.5 0.14 0.44 150 210 11.2 0.34 1190

13 42 HRc 0.5 1.5 0.14 0.40 90 150 11.2 0.30 1130

15 150 HB 0.5 4.0 0.17 0.58 150 240 44.0 0.46 2200

15 200 HB 0.5 4.0 0.17 0.58 150 220 44.0 0.46 1180

16 250 HB 0.5 4.0 0.17 0.58 150 190 44.0 0.46 1160

17,19 150 HB 0.5 4.0 0.14 0.52 100 200 44.0 0.40 1180

17,19 200 HB 0.5 4.0 0.14 0.52 100 180 44.0 0.40 1150

18,20 250 HB 0.5 4.0 0.14 0.52 100 150 44.0 0.40 1130

31,32 Incoloy 800 240 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 332

33 Inconel 700 250 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 330

34 Stellite 21 350 HB 0.5 1.5 0.11 0.36 25 45 11.2 0.30 330

36 TiAl6V4 - 0.5 1.5 0.11 0.40 40 65 11.2 0.34 555

37 T40 - 0.5 1.5 0.11 0.36 30 55 11.2 0.30 440

38 45 HRc 0.4 3.0 0.10 0.36 40 80 22.0 0.28 660

38 50 HRc 0.4 3.0 0.10 0.32 40 70 11.0 0.26 555

38 55 HRc 0.4 1.5 0.10 0.28 40 60 00.5 0.24 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.5 0.17 0.60 200 400 11.5 0.50 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

ONKX 0806-45 – LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

255

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


Ø d

Shape Clearance Angle Fixing, Chipbreaker

Tolerance

15°

s

s ± 0.13For l = 06/08/10, d ± 0.05For l = 12, d ± 0.08

l

R D M T

Copying

Surfacing

SlottingPocket MillingHelical Interpolation

M0000039

M0001876

M0000038

M0001875

M0000037

M0001882

M0000035

M0001881

Neutral-

Neutral-

Neutral-

Neutral-

Neutral-

Neutral-

Neutral-

Neutral-

4.76

3.97

3.97

3.18

3.18

2.38

2.38

4.76

12

12

10

10

8

7

6

16

RDMT 1204 M0 LT 30

RDMT 12T3 M0 LT 30

RDMT 10T3 M0 LT 30

RDMT 1003 M0 LT 30

RDMT 0803 M0 LT 30

RDMT 0702 M0 LT 30

RDMT 0602 M0 LT 30

RDMT 1604 M0 LT 30


LT 30 Multi-MatTM General Usage – StandardRDMT

256

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


R D M T

M0002226

M0002227

M0002225

M0002224

M0003405

M0003404

M0003403

M0003407

Neutral

Neutral

Neutral

Neutral

Neutral

Neutral

Neutral

-

-

-

-

-

-

-

- Neutral

4.76

3.97

3.97

3.18

3.18

2.38

2.38

4.76

12

12

10

10

8

7

6

16

RDMT 1204 M0 LT 3000

RDMT 12T3 M0 LT 3000

RDMT 10T3 M0 LT 3000

RDMT 1003 M0 LT 3000

RDMT 0803 M0 LT 3000

RDMT 0702 M0 LT 3000

RDMT 0602 M0 LT 3000

RDMT 1604 M0 LT 3000



Copying SurfacingPocket-MillingHelical Interpolation

MILLING

257

Cutters

End Mill for RDMT 0602 M0



End Mill for RDMT 10T3 M0

Screw:Key:

M2001416M2002912

Screw:Key:

M2004402M2000601

Screw:Key:

M2001416M2002912

Screw:Key:

M2000597M2000602

Cutter Designation

Cutter Designation

Cutter Designation

Cutter Designation

LT 060 WL-W-D016/2

LT 080 WL-W-D020/2

LT 070 WL-W D025/4

LT 100 WL-W D032/3

LT 060 WL-W-D012/2

LT 080 WL-W-D016/2

LT 060 WL-W-D020/3

LT 080 WL-W-D025/3

LT 060 WL-W-D025/3

LT 080 WL-W-D032/3

Catalog Nr.

Catalog Nr.

Catalog Nr.

Catalog Nr.

M2000676

M2000679

M2003339

M2000685

M2003321

M2003322

M2000677

M2000680

M2000678

M2000681

D

D

D

D

16

20

25

32

12

16

20

25

25

32

z

z

z

z

2

2

4

3

2

2

3

3

3

3

Ap

Ap

Ap

Ap

3

4

3.5

5

3

4

3

4

3

4

D1

D1

D1

D1

10

12

18

22

6

8

14

17

19

24

d

d

d

d

L

L

L

L

L1

L1

L1

L1

16

16

25

32

16

16

150

180

180

180

25

42

60

80

150

150

25

25

20

20

180

180

60

60

25

25

180

180

80

80

α Ramp°

α Ramp°

α Ramp°

α Ramp°

6

6

4

5

7

12

LT 070 WL-W D020/3 M200333720 33.513 20 180 60 4.5

LT 100 WL-W D025/3 M200068425 3515 25 180 60 8

4.5

4.5

LT 070 WL-W-D016/2 M200333616 23.59 16 150 25 6

LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12

4

4

DD1

L1

Ap

L

d

MILLING

258

Cutters


Shell Mill for RDMT 1204 M0

Shell Mill for RDMT 1604 M0

Screw:Key:

M2000597M2000602

Screw:Key:

M2000597M2000602

Screw:Key:

M2000599M2000603

Cutter Designation

Cutter Designation

Cutter Designation

LT 120 M-W-D063/5

LT 160 M-W-D080/6

LT 120 M-W-D100/7

LT 160 M-W-D125/8

Catalog Nr.

Catalog Nr.

Catalog Nr.

M2000689

M2003333

M2000688

M2003335

D

D

D

63

80

100

125

z

z

z

5

6

7

8

Ap

Ap

Ap

6

6

6

6

D1

D1

D1

51

64

88

109

d

d

d

L

L

L

L1

22

27

40

40

40

50

50

63

α Ramp°

α Ramp°

α Ramp°

3.5

2.5

1.5

1

LT 120 WL-W-D040/4 M200068740 4628 32 170 110 7

LT 120 M-W-D050/4

LT 160 M-W-D063/5

M2001780

M2003332

50

63

4

5

6

6

38

47

22

22

40

50

5

3.5

LT 120 M-W-D080/6

LT 160 M-W-D100/7

M2000690

M2003334

80

100

6

7

6

6

68

84

27

32

50

50

2.5

2

LT 120 WL-W-D032/3 M200332332 3620 32 170 60 5

LT 120 M-W-D040/4

LT 160 M-W-D050/4

M2000691

M2003331

40

50

4

4

6

6

28

34

16

22

40

50

7

5

DD1

L1

Ap

L

d

D

D1

Ap

L

d

MILLING

259


RDMT 0602 M0 – LT 30 | LT 3000


1 125 HB 0.5 1.5 0.18 0.48 190 330 00.8 0.29 2250

2 190 HB 0.5 1.5 0.18 0.48 190 300 00.8 0.29 2220

3 250 HB 0.5 1.5 0.18 0.48 190 250 00.8 0.29 2200

6 180 HB 0.5 1.5 0.15 0.38 150 240 00.8 0.25 2200

4,6 230 HB 0.5 1.5 0.15 0.38 150 210 00.8 0.25 1180

5,7 280 HB 0.5 1.5 0.15 0.33 130 190 00.8 0.23 1150

8 350 HB 0.5 1.5 0.15 0.33 130 170 00.8 0.23 1140

10 220 HB 0.5 1.1 0.12 0.33 90 150 00.6 0.23 1130

10 280 HB 0.5 1.1 0.12 0.33 90 130 00.6 0.23 1120

11 320 HB 0.5 1.1 0.12 0.27 60 110 00.6 0.20 1100

11 350 HB 0.5 1.1 0.12 0.27 60 90 00.6 0.20 880

14 180 HB 0.5 1.5 0.15 0.38 190 250 00.8 0.25 2220

14 240 HB 0.5 1.5 0.12 0.33 160 210 00.8 0.25 1190

14 290 HB 0.5 1.2 0.12 0.27 70 130 00.6 0.20 1100

14 310 HB 0.5 1.2 0.12 0.27 70 120 00.6 0.20 990

12 200 HB 0.5 1.5 0.15 0.38 150 210 00.8 0.25 1190

13 42 HRc 0.5 1.2 0.15 0.30 90 150 00.6 0.20 1130

15 150 HB 0.5 1.5 0.18 0.48 150 240 00.8 0.29 2200

15 200 HB 0.5 1.5 0.18 0.48 150 220 00.8 0.29 1180

16 250 HB 0.5 1.5 0.18 0.48 150 190 00.8 0.29 1160

17,19 150 HB 0.5 1.5 0.15 0.42 100 200 00.8 0.25 1180

17,19 200 HB 0.5 1.5 0.15 0.42 100 180 00.8 0.25 1150

18,20 250 HB 0.5 1.5 0.15 0.42 100 150 00.8 0.25 1130

31,32 Incoloy 800 240 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 332

33 Inconel 700 250 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 330

34 Stellite 21 350 HB 0.5 1.2 0.12 0.27 25 45 00.6 0.20 330

36 TiAl6V4 - 0.5 1.2 0.12 0.30 40 65 00.6 0.23 555

37 T40 - 0.5 1.2 0.12 0.27 30 55 00.6 0.20 440

38 45 HRc 0.3 0.6 0.10 0.27 40 80 00.4 0.18 660

38 50 HRc 0.3 0.4 0.10 0.24 40 70 00.3 0.16 555

38 55 HRc 0.3 0.4 0.10 0.21 40 60 00.3 0.15 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.5 0.18 0.48 200 400 00.8 0.31 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

260



1 125 HB 0.5 1.8 0.18 0.54 190 330 00.8 0.32 2250

2 190 HB 0.5 1.8 0.18 0.54 190 300 00.8 0.32 2220

3 250 HB 0.5 1.8 0.18 0.54 190 250 00.8 0.32 2200

6 180 HB 0.5 1.8 0.15 0.43 150 240 00.8 0.28 2200

4,6 230 HB 0.5 1.8 0.15 0.43 150 210 00.8 0.28 1180

5,7 280 HB 0.5 1.8 0.15 0.37 130 190 00.8 0.25 1150

8 350 HB 0.5 1.8 0.15 0.37 130 170 00.8 0.25 1140

10 220 HB 0.5 1.3 0.12 0.37 90 150 00.6 0.25 1130

10 280 HB 0.5 1.3 0.12 0.37 90 130 00.6 0.25 1120

11 320 HB 0.5 1.3 0.12 0.31 60 110 00.6 0.22 1100

11 350 HB 0.5 1.3 0.12 0.31 60 90 00.6 0.22 880

14 180 HB 0.5 1.8 0.15 0.43 190 250 00.8 0.28 2220

14 240 HB 0.5 1.8 0.12 0.37 160 210 00.8 0.28 1190

14 290 HB 0.5 1.4 0.12 0.31 70 130 00.6 0.22 1100

14 310 HB 0.5 1.4 0.12 0.31 70 120 00.6 0.22 990

12 200 HB 0.5 1.8 0.15 0.43 150 210 00.8 0.28 1190

13 42 HRc 0.5 1.4 0.15 0.34 90 150 00.6 0.22 1130

15 150 HB 0.5 1.8 0.18 0.54 150 240 00.8 0.32 2200

15 200 HB 0.5 1.8 0.18 0.54 150 220 00.8 0.32 1180

16 250 HB 0.5 1.8 0.18 0.54 150 190 00.8 0.32 1160

17,19 150 HB 0.5 1.8 0.15 0.48 100 200 00.8 0.28 1180

17,19 200 HB 0.5 1.8 0.15 0.48 100 180 00.8 0.28 1150

18,20 250 HB 0.5 1.8 0.15 0.48 100 150 00.8 0.28 1130

31,32 Incoloy 800 240 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 332

33 Inconel 700 250 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 330

34 Stellite 21 350 HB 0.5 1.4 0.12 0.31 25 45 00.6 0.22 330

36 TiAl6V4 - 0.5 1.4 0.12 0.34 40 65 00.6 0.25 555

37 T40 - 0.5 1.4 0.12 0.31 30 55 00.6 0.22 440

38 45 HRc 0.3 0.7 0.10 0.31 40 80 00.4 0.20 660

38 50 HRc 0.3 0.5 0.10 0.27 40 70 00.3 0.18 555

38 55 HRc 0.3 0.5 0.10 0.24 40 60 00.3 0.17 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 1.8 0.18 0.54 200 400 00.8 0.35 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

RDMT 0702 M0 – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

261


RDMT 0803 M0 – LT 30 | LT 3000


1 125 HB 0.5 2.0 0.18 0.58 190 330 00.8 0.35 2250

2 190 HB 0.5 2.0 0.18 0.58 190 300 00.8 0.35 2220

3 250 HB 0.5 2.0 0.18 0.58 190 250 00.8 0.35 2200

6 180 HB 0.5 2.0 0.15 0.45 150 240 00.8 0.30 2200

4,6 230 HB 0.5 2.0 0.15 0.45 150 210 00.8 0.30 1180

5,7 280 HB 0.5 2.0 0.15 0.40 130 190 00.8 0.27 1150

8 350 HB 0.5 2.0 0.15 0.40 130 170 00.8 0.27 1140

10 220 HB 0.5 1.4 0.12 0.40 90 150 00.6 0.27 1130

10 280 HB 0.5 1.4 0.12 0.40 90 130 00.6 0.27 1120

11 320 HB 0.5 1.4 0.12 0.32 60 110 00.6 0.24 1100

11 350 HB 0.5 1.4 0.12 0.32 60 90 00.6 0.24 880

14 180 HB 0.5 2.0 0.15 0.45 190 250 00.8 0.30 2220

14 240 HB 0.5 2.0 0.12 0.40 160 210 00.8 0.30 1190

14 290 HB 0.5 1.5 0.12 0.32 70 130 00.6 0.24 1100

14 310 HB 0.5 1.5 0.12 0.32 70 120 00.6 0.24 990

12 200 HB 0.5 2.0 0.15 0.45 150 210 00.8 0.30 1190

13 42 HRc 0.5 1.5 0.15 0.36 90 150 00.6 0.24 1130

15 150 HB 0.5 2.0 0.18 0.58 150 240 00.8 0.35 2200

15 200 HB 0.5 2.0 0.18 0.58 150 220 00.8 0.35 1180

16 250 HB 0.5 2.0 0.18 0.58 150 190 00.8 0.35 1160

17,19 150 HB 0.5 2.0 0.15 0.50 100 200 00.8 0.30 1180

17,19 200 HB 0.5 2.0 0.15 0.50 100 180 00.8 0.30 1150

18,20 250 HB 0.5 2.0 0.15 0.50 100 150 00.8 0.30 1130

31,32 Incoloy 800 240 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 332

33 Inconel 700 250 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 330

34 Stellite 21 350 HB 0.5 1.5 0.12 0.32 25 45 00.6 0.24 330

36 TiAl6V4 - 0.5 1.5 0.12 0.36 40 65 00.6 0.27 555

37 T40 - 0.5 1.5 0.12 0.32 30 55 00.6 0.24 440

38 45 HRc 0.3 0.7 0.10 0.32 40 80 00.4 0.21 660

38 50 HRc 0.3 0.6 0.10 0.29 40 70 00.3 0.20 555

38 55 HRc 0.3 0.5 0.10 0.25 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.0 0.18 0.58 200 400 00.8 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

262



1 125 HB 0.5 2.5 0.18 0.64 190 330 11.0 0.35 2250

2 190 HB 0.5 2.5 0.18 0.64 190 300 11.0 0.35 2220

3 250 HB 0.5 2.5 0.18 0.64 190 250 11.0 0.35 2200

6 180 HB 0.5 2.5 0.15 0.50 150 240 11.0 0.30 2200

4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1180

5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.0 0.27 1150

8 350 HB 0.5 2.5 0.15 0.44 130 170 11.0 0.27 1140

10 220 HB 0.5 1.8 0.12 0.44 90 150 00.8 0.27 1130

10 280 HB 0.5 1.8 0.12 0.44 90 130 00.8 0.27 1120

11 320 HB 0.5 1.8 0.12 0.36 60 110 00.8 0.24 1100

11 350 HB 0.5 1.8 0.12 0.36 60 90 00.8 0.24 880

14 180 HB 0.5 2.5 0.15 0.50 190 250 11.0 0.30 2220

14 240 HB 0.5 2.5 0.12 0.44 160 210 11.0 0.30 1190

14 290 HB 0.5 2.0 0.12 0.36 70 130 00.8 0.24 1100

14 310 HB 0.5 2.0 0.12 0.36 70 120 00.8 0.24 990

12 200 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1190

13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.8 0.24 1130

15 150 HB 0.5 2.5 0.18 0.64 150 240 11.0 0.35 2200

15 200 HB 0.5 2.5 0.18 0.64 150 220 11.0 0.35 1180

16 250 HB 0.5 2.5 0.18 0.64 150 190 11.0 0.35 1160

17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.0 0.30 1180

17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.0 0.30 1150

18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 332

33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330

34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330

36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.8 0.27 555

37 T40 - 0.5 2.0 0.12 0.36 30 55 00.8 0.24 440

38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.5 0.21 660

38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.4 0.20 555

38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.0 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

RDMT 10T3 M0 – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

263


RDMT 1003 M0 – LT 30 | LT 3000


1 125 HB 0.5 2.5 0.18 0.64 190 330 11.0 0.35 2250

2 190 HB 0.5 2.5 0.18 0.64 190 300 11.0 0.35 2220

3 250 HB 0.5 2.5 0.18 0.64 190 250 11.0 0.35 2200

6 180 HB 0.5 2.5 0.15 0.50 150 240 11.0 0.30 2200

4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1180

5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.0 0.27 1150

8 350 HB 0.5 2.5 0.15 0.44 130 170 11.0 0.27 1140

10 220 HB 0.5 1.8 0.12 0.44 90 150 00.8 0.27 1130

10 280 HB 0.5 1.8 0.12 0.44 90 130 00.8 0.27 1120

11 320 HB 0.5 1.8 0.12 0.36 60 110 00.8 0.24 1100

11 350 HB 0.5 1.8 0.12 0.36 60 90 00.8 0.24 880

14 180 HB 0.5 2.5 0.15 0.50 190 250 11.0 0.30 2220

14 240 HB 0.5 2.5 0.12 0.44 160 210 11.0 0.30 1190

14 290 HB 0.5 2.0 0.12 0.36 70 130 00.8 0.24 1100

14 310 HB 0.5 2.0 0.12 0.36 70 120 00.8 0.24 990

12 200 HB 0.5 2.5 0.15 0.50 150 210 11.0 0.30 1190

13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.8 0.24 1130

15 150 HB 0.5 2.5 0.18 0.64 150 240 11.0 0.35 2200

15 200 HB 0.5 2.5 0.18 0.64 150 220 11.0 0.35 1180

16 250 HB 0.5 2.5 0.18 0.64 150 190 11.0 0.35 1160

17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.0 0.30 1180

17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.0 0.30 1150

18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 332

33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330

34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.8 0.24 330

36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.8 0.27 555

37 T40 - 0.5 2.0 0.12 0.36 30 55 00.8 0.24 440

38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.5 0.21 660

38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.4 0.20 555

38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.0 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

264


RDMT 12T3 M0 – LT 30 | LT 3000


1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250

2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220

3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200

6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200

4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180

5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150

8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140

10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130

10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120

11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100

11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880

14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220

14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190

14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100

14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990

12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190

13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130

15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200

15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180

16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160

17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180

17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150

18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130

31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332

33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555

37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440

38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660

38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555

38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 11.3 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

265


RDMT 1204 M0 – LT 30 | LT 3000


1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250

2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220

3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200

6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200

4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180

5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150

8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140

10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130

10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120

11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100

11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880

14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220

14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190

14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100

14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990

12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190

13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130

15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200

15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180

16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160

17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180

17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150

18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130

31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332

33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555

37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440

38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660

38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555

38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 11.3 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

266



1 125 HB 0.5 4.0 0.25 1.00 190 330 22.0 0.35 2250

2 190 HB 0.5 4.0 0.25 1.00 190 300 22.0 0.35 2220

3 250 HB 0.5 4.0 0.25 1.00 190 250 22.0 0.35 2200

6 180 HB 0.5 4.0 0.21 0.78 150 240 22.0 0.30 2200

4,6 230 HB 0.5 4.0 0.21 0.78 150 210 22.0 0.30 1180

5,7 280 HB 0.5 4.0 0.21 0.69 130 190 22.0 0.27 1150

8 350 HB 0.5 4.0 0.21 0.69 130 170 22.0 0.27 1140

10 220 HB 0.5 2.9 0.17 0.69 90 150 11.5 0.27 1130

10 280 HB 0.5 2.9 0.17 0.69 90 130 11.5 0.27 1120

11 320 HB 0.5 2.9 0.17 0.56 60 110 11.5 0.24 1100

11 350 HB 0.5 2.9 0.17 0.56 60 90 11.5 0.24 880

14 180 HB 0.5 4.0 0.21 0.78 190 250 22.0 0.30 2220

14 240 HB 0.5 4.0 0.17 0.69 160 210 22.0 0.30 1190

14 290 HB 0.5 3.1 0.17 0.56 70 130 11.5 0.24 1100

14 310 HB 0.5 3.1 0.17 0.56 70 120 11.5 0.24 990

12 200 HB 0.5 4.0 0.21 0.78 150 210 22.0 0.30 1190

13 42 HRc 0.5 3.1 0.21 0.63 90 150 11.5 0.24 1130

15 150 HB 0.5 4.0 0.25 1.00 150 240 22.0 0.35 2200

15 200 HB 0.5 4.0 0.25 1.00 150 220 22.0 0.35 1180

16 250 HB 0.5 4.0 0.25 1.00 150 190 22.0 0.35 1160

17,19 150 HB 0.5 4.0 0.21 0.88 100 200 22.0 0.30 1180

17,19 200 HB 0.5 4.0 0.21 0.88 100 180 22.0 0.30 1150

18,20 250 HB 0.5 4.0 0.21 0.88 100 150 22.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 332

33 Inconel 700 250 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 330

34 Stellite 21 350 HB 0.5 3.1 0.17 0.56 25 45 11.5 0.24 330

36 TiAl6V4 - 0.5 3.1 0.17 0.63 40 65 11.5 0.27 555

37 T40 - 0.5 3.1 0.17 0.56 30 55 11.5 0.24 440

38 45 HRc 0.4 1.4 0.14 0.56 40 80 11.0 0.21 660

38 50 HRc 0.4 1.1 0.14 0.50 40 70 00.8 0.20 555

38 55 HRc 0.4 1.0 0.14 0.44 40 60 00.5 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 4.0 0.25 1.00 200 400 22.0 0.38 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

RDMT 1604 M0 – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

267

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


R D M Ws

Shape Clearance Angle Toleranced ± 0.05s ± 0.13

15°

Fixing,Chipbreaker

Ø dl

Copying SurfacingPocket MillingHelical Interpolation

Shap

M0001551

M0001550

-

-

Neutral

Neutral

4.76

3.97

12

10

RDMW 1204 M0 LT 30

RDMW 10T3 M0 LT 30



M0003408

M0002228

-

-

Neutral

Neutral

4.76

3.97

12

10

RDMW 1204 M0 LT 3000

RDMW 10T3 M0 LT 3000



RDMW

MILLING

268

Cutters

End Mill for RDMW 10T3 M0

Screw:Key:

M2000597M2000602

Cutter Designation

LT 100 WL-W D032/3

Catalog Nr.

M2000685

D

32

z

3

Ap

5

D1

22

d L L1

32 180 80

α Ramp°

5

LT 100 WL-W D025/3 M200068425 3515 25 180 60 8

LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12

DD1

L1

Ap

L

d

Shell Mill for RDMW 1204 M0

Screw:Key:

M2000597M2000602

Cutter Designation

LT 120 M-W-D063/5

LT 120 M-W-D100/7

Catalog Nr.

M2000689

M2000688

D

63

100

z

5

7

Ap

6

6

D1

51

88

d L

22

40

40

50

α Ramp°

3.5

1.5

LT 120 M-W-D050/4 M200178050 4638 22 40 5

LT 120 M-W-D080/6 M200069080 6668 27 50 2.5

LT 120 M-W-D040/4 M200069140 4628 16 40 7

D

D1

Ap

L

d

MILLING

269


RDMW 10T3 M0 – LT 30 | LT 3000


1 125 HB 0.5 2.5 0.18 0.70 190 330 11.0 0.39 2250

2 190 HB 0.5 2.5 0.18 0.70 190 300 11.0 0.39 2220

3 250 HB 0.5 2.5 0.18 0.70 190 250 11.0 0.39 2200

6 180 HB 0.5 2.5 0.15 0.55 150 240 11.0 0.34 2200

4,6 230 HB 0.5 2.5 0.15 0.55 150 210 11.0 0.34 1180

5,7 280 HB 0.5 2.5 0.15 0.48 130 190 11.0 0.31 1150

8 350 HB 0.5 2.5 0.15 0.48 130 170 11.0 0.31 1140

10 220 HB 0.5 1.8 0.12 0.48 90 150 00.8 0.31 1130

10 280 HB 0.5 1.8 0.12 0.48 90 130 00.8 0.31 1120

11 320 HB 0.5 1.8 0.12 0.40 60 110 00.8 0.27 1100

11 350 HB 0.5 1.8 0.12 0.40 60 90 00.8 0.27 880

15 150 HB 0.5 2.5 0.18 0.70 150 240 11.0 0.39 2200

15 200 HB 0.5 2.5 0.18 0.70 150 220 11.0 0.39 1180

16 250 HB 0.5 2.5 0.18 0.70 150 190 11.0 0.39 1160

17,19 150 HB 0.5 2.5 0.15 0.62 100 200 11.0 0.34 1180

17,19 200 HB 0.5 2.5 0.15 0.62 100 180 11.0 0.34 1150

18,20 250 HB 0.5 2.5 0.15 0.62 100 150 11.0 0.34 1130

38 45 HRc 0.3 0.9 0.10 0.40 40 80 00.5 0.24 660

38 50 HRc 0.3 0.7 0.10 0.35 40 70 00.4 0.22 555

38 55 HRc 0.3 0.6 0.10 0.31 40 60 00.3 0.20 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

MILLING

270


RDMW 1204 M0 – LT 30 | LT 3000


1 125 HB 0.5 2.5 0.18 0.70 190 330 11.0 00.39 2250

2 190 HB 0.5 2.5 0.18 0.70 190 300 11.0 00.39 2220

3 250 HB 0.5 2.5 0.18 0.70 190 250 11.0 00.39 2200

6 180 HB 0.5 2.5 0.15 0.55 150 240 11.0 00.34 2200

4,6 230 HB 0.5 2.5 0.15 0.55 150 210 11.0 00.34 1180

5,7 280 HB 0.5 2.5 0.15 0.48 130 190 11.0 00.31 1150

8 350 HB 0.5 2.5 0.15 0.48 130 170 11.0 00.31 1140

10 220 HB 0.5 1.8 0.12 0.48 90 150 00.8 00.31 1130

10 280 HB 0.5 1.8 0.12 0.48 90 130 00.8 00.31 1120

11 320 HB 0.5 1.8 0.12 0.40 60 110 00.8 00.27 1100

11 350 HB 0.5 1.8 0.12 0.40 60 90 00.8 00.27 880

15 150 HB 0.5 2.5 0.18 0.70 150 240 11.0 00.39 2200

15 200 HB 0.5 2.5 0.18 0.70 150 220 11.0 00.39 1180

16 250 HB 0.5 2.5 0.18 0.70 150 190 11.0 00.39 1160

17,19 150 HB 0.5 2.5 0.15 0.62 100 200 11.0 00.34 1180

17,19 200 HB 0.5 2.5 0.15 0.62 100 180 11.0 00.34 1150

18,20 250 HB 0.5 2.5 0.15 0.62 100 150 11.0 00.34 1130

38 45 HRc 0.3 0.9 0.10 0.40 40 80 00.5 00.24 660

38 50 HRc 0.3 0.7 0.10 0.35 40 70 00.4 00.22 555

38 55 HRc 0.3 0.6 0.10 0.31 40 60 00.3 00.20 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

271

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


R D M Xs

Shape Clearance Angle Toleranced ± 0.05s ± 0.13

15°

Fixing,Chipbreaker

Ø dl

Copying SurfacingPocket MillingHelical Interpolation

Shape

M0001553

M0001552

-

-

Neutral

Neutral

4.76

3.97

12

10

RDMX 1204 M0 LT 30

RDMX 10T3 M0 LT 30



M0003410

M0003409

-

-

Neutral

Neutral

4.76

3.97

12

10

RDMX 1204 M0 LT 3000

RDMX 10T3 M0 LT 3000



RDMX

MILLING

272

Cutters

End Mill for RDMX 10T3 M0

Screw:Key:

M2000597M2000602

Cutter Designation

LT 100 WL-W D032/3

Catalog Nr.

M2000685

D

32

z

3

Ap

5

D1

22

d L L1

32 180 80

α Ramp°

5

LT 100 WL-W D025/3 M200068425 3515 25 180 60 8

LT 100 WL-W-D020/2 M200068320 2510 20 180 80 12

Shell Mill for RDMX 1204 M0

Screw:Key:

M2000597M2000602

Cutter Designation

LT 120 M-W-D063/5

LT 120 M-W-D100/7

Catalog Nr.

M2000689

M2000688

D

63

100

z

5

7

Ap

6

6

D1

51

88

d L

22

40

40

50

α Ramp°

3.5

1.5

LT 120 M-W-D050/4 M200178050 4638 22 40 5

LT 120 M-W-D080/6 M200069080 6668 27 50 2.5

LT 120 M-W-D040/4 M200069140 4628 16 40 7

DD1

L1

Ap

L

d

D

D1

Ap

L

d

MILLING

273


RDMX 10T3 M0 – LT 30 | LT 3000


1 125 HB 0.5 2.5 0.18 0.64 190 330 11.000 0.345 2250

2 190 HB 0.5 2.5 0.18 0.64 190 300 11.000 0.345 2220

3 250 HB 0.5 2.5 0.18 0.64 190 250 11.000 0.345 2200

6 180 HB 0.5 2.5 0.15 0.50 150 240 11.000 0.300 2200

4,6 230 HB 0.5 2.5 0.15 0.50 150 210 11.000 0.300 1180

5,7 280 HB 0.5 2.5 0.15 0.44 130 190 11.000 0.270 1150

8 350 HB 0.5 2.5 0.15 0.44 130 170 11.000 0.270 1140

10 220 HB 0.5 1.8 0.12 0.44 90 150 00.750 0.270 1130

10 280 HB 0.5 1.8 0.12 0.44 90 130 00.750 0.270 1120

11 320 HB 0.5 1.8 0.12 0.36 60 110 00.750 0.240 1100

11 350 HB 0.5 1.8 0.12 0.36 60 90 00.750 0.240 880

14 180 HB 0.5 2.5 0.15 0.50 190 250 11.000 0.300 2220

14 240 HB 0.5 2.5 0.12 0.44 160 210 11.000 0.300 1190

14 290 HB 0.5 2.0 0.12 0.36 70 130 00.750 0.240 1100

14 310 HB 0.5 2.0 0.12 0.36 70 120 00.750 0.240 990

12 200 HB 0.5 2.5 0.15 0.50 150 210 11.000 0.300 1190

13 42 HRc 0.5 2.0 0.15 0.40 90 150 00.750 0.240 1130

15 150 HB 0.5 2.5 0.18 0.64 150 240 11.000 0.345 2200

15 200 HB 0.5 2.5 0.18 0.64 150 220 11.000 0.345 1180

16 250 HB 0.5 2.5 0.18 0.64 150 190 11.000 0.345 1160

17,19 150 HB 0.5 2.5 0.15 0.56 100 200 11.000 0.300 1180

17,19 200 HB 0.5 2.5 0.15 0.56 100 180 11.000 0.300 1150

18,20 250 HB 0.5 2.5 0.15 0.56 100 150 11.000 0.300 1130

31,32 Incoloy 800 240 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 332

33 Inconel 700 250 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 330

34 Stellite 21 350 HB 0.5 2.0 0.12 0.36 25 45 00.750 0.240 330

36 TiAl6V4 - 0.5 2.0 0.12 0.40 40 65 00.750 0.270 555

37 T40 - 0.5 2.0 0.12 0.36 30 55 00.750 0.240 440

38 45 HRc 0.3 0.9 0.10 0.36 40 80 00.500 0.210 660

38 50 HRc 0.3 0.7 0.10 0.32 40 70 00.375 0.195 555

38 55 HRc 0.3 0.6 0.10 0.28 40 60 00.250 0.180 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 2.5 0.18 0.64 200 400 11.000 0.375 280

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

1C35, Ck45, 1020, 1045, 1060, 28Mn6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

2

X100CrMo13, 440C,

G-X260NiCr42 11

4304, 316,

X5CrNi18-9

5

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

274


RDMX 1204 M0 – LT 30 | LT 3000


1 125 HB 0.5 3.0 0.25 0.74 190 330 11.3 0.35 2250

2 190 HB 0.5 3.0 0.25 0.74 190 300 11.3 0.35 2220

3 250 HB 0.5 3.0 0.25 0.74 190 250 11.3 0.35 2200

6 180 HB 0.5 3.0 0.21 0.58 150 240 11.3 0.30 2200

4,6 230 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1180

5,7 280 HB 0.5 3.0 0.21 0.51 130 190 11.3 0.27 1150

8 350 HB 0.5 3.0 0.21 0.51 130 170 11.3 0.27 1140

10 220 HB 0.5 2.2 0.17 0.51 90 150 11.0 0.27 1130

10 280 HB 0.5 2.2 0.17 0.51 90 130 11.0 0.27 1120

11 320 HB 0.5 2.2 0.17 0.41 60 110 11.0 0.24 1100

11 350 HB 0.5 2.2 0.17 0.41 60 90 11.0 0.24 880

14 180 HB 0.5 3.0 0.21 0.58 190 250 11.3 0.30 2220

14 240 HB 0.5 3.0 0.17 0.51 160 210 11.3 0.30 1190

14 290 HB 0.5 2.4 0.17 0.41 70 130 11.0 0.24 1100

14 310 HB 0.5 2.4 0.17 0.41 70 120 11.0 0.24 990

12 200 HB 0.5 3.0 0.21 0.58 150 210 11.3 0.30 1190

13 42 HRc 0.5 2.4 0.21 0.46 90 150 11.0 0.24 1130

15 150 HB 0.5 3.0 0.25 0.74 150 240 11.3 0.35 2200

15 200 HB 0.5 3.0 0.25 0.74 150 220 11.3 0.35 1180

16 250 HB 0.5 3.0 0.25 0.74 150 190 11.3 0.35 1160

17,19 150 HB 0.5 3.0 0.21 0.64 100 200 11.3 0.30 1180

17,19 200 HB 0.5 3.0 0.21 0.64 100 180 11.3 0.30 1150

18,20 250 HB 0.5 3.0 0.21 0.64 100 150 11.3 0.30 1130

31,32 Incoloy 800 240 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 332

33 Inconel 700 250 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

34 Stellite 21 350 HB 0.5 2.4 0.17 0.41 25 45 11.0 0.24 330

36 TiAl6V4 - 0.5 2.4 0.17 0.46 40 65 11.0 0.27 555

37 T40 - 0.5 2.4 0.17 0.41 30 55 11.0 0.24 440

38 45 HRc 0.3 1.1 0.14 0.41 40 80 00.7 0.21 660

38 50 HRc 0.3 0.9 0.14 0.37 40 70 00.5 0.20 555

38 55 HRc 0.3 0.8 0.14 0.32 40 60 00.3 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 3.0 0.25 0.74 200 400 1.3 0.38 280

GG20, GG40, EN-GJL-250,

No30B

X100CrMo13, 440C,

G-X260NiCr42 11

8GGG40, GGG70,

50005

9

10

7

C35, Ck45, 1020, 1045, 1060, 28Mn6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

2

1














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

275

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S D K T


Toleranced ± 0.08m ± 0.013s ± 0.025

90°l

mØ d

15°

s


M0000171- Neutral4.7612.70SDKT 1204 AETN LT 30



M0003411- Neutral4.7612.70SDKT 1204 AETN LT 3000



SDKT

MILLING

276

Cutters

Shell Mill for SDKT 1204 AETN

Screw:Key:

M2000598M2000603

Cutter Designation

LT 670 M-W-D063/5*

LT 670 M-W-D050/4*

LT 670 M-W-D125/7*

LT 670 M-W-D080/6*

LT 670 M-W-D100/6*

LT 670 M-W-D160/8*

Catalog Nr.

M2000555

M2000553

M2000558

M2000556

M2000557

M2000559

D

76

63

138

93

113

173

z

5

4

7

6

6

8

Ap

6

6

6

6

6

6

D1

63

50

125

80

100

160

d

22

22

40

27

32

40

L

48

48

63

50

50

63

DD1

d

Ap

L

45°

* On request

MILLING

277



1 125 HB 0.5 7.0 0.18 0.53 190 330 33.0 0.39 2250

2 190 HB 0.5 7.0 0.18 0.53 190 300 33.0 0.39 2220

3 250 HB 0.5 7.0 0.18 0.53 190 250 33.0 0.39 2200

6 180 HB 0.5 7.0 0.15 0.41 150 240 33.0 0.34 2200

4,6 230 HB 0.5 7.0 0.15 0.41 150 210 33.0 0.34 1180

5,7 280 HB 0.5 7.0 0.15 0.36 130 190 33.0 0.31 1150

8 350 HB 0.5 7.0 0.15 0.36 130 170 33.0 0.31 1140

10 220 HB 0.5 5.0 0.12 0.36 90 150 22.3 0.31 1130

10 280 HB 0.5 5.0 0.12 0.36 90 130 22.3 0.31 1120

11 320 HB 0.5 5.0 0.12 0.30 60 110 22.3 0.27 1100

11 350 HB 0.5 5.0 0.12 0.30 60 90 22.3 0.27 880

14 180 HB 0.5 7.0 0.15 0.36 190 250 33.0 0.31 2220

14 240 HB 0.5 7.0 0.12 0.33 160 210 33.0 0.31 1190

14 290 HB 0.5 5.0 0.12 0.30 70 130 22.3 0.27 1100

14 310 HB 0.5 5.0 0.12 0.30 70 120 22.3 0.27 990

12 200 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.31 1190

13 42 HRc 0.5 5.0 0.15 0.30 90 150 22.3 0.27 1130

15 150 HB 0.5 7.0 0.18 0.53 150 240 33.0 0.39 2200

15 200 HB 0.5 7.0 0.18 0.53 150 220 33.0 0.39 1180

16 250 HB 0.5 7.0 0.18 0.53 150 190 33.0 0.39 1160

17,19 150 HB 0.5 7.0 0.15 0.46 100 200 33.0 0.34 1180

17,19 200 HB 0.5 7.0 0.15 0.46 100 180 33.0 0.34 1150

18,20 250 HB 0.5 7.0 0.15 0.46 100 150 33.0 0.34 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.30 25 45 22.3 0.27 330

36 TiAl6V4 - 0.5 5.0 0.12 0.33 40 65 22.3 0.31 555

37 T40 - 0.5 5.0 0.12 0.30 30 55 22.3 0.27 440

38 45 HRc 0.5 2.5 0.10 0.30 40 80 11.5 0.24 660

38 50 HRc 0.5 1.8 0.10 0.26 40 70 11.1 0.22 555

38 55 HRc 0.5 1.5 0.10 0.23 40 60 00.8 0.20 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.53 200 400 33.0 0.43 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

SDKT 1204 AETN – LT 30 | LT 3000


GroupMaterial

ExemplesHardness


Parameters















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

278

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC



90°l

mØ d

15°

Fixing,Chipbreaker

ss

Copying Pocket MillingPlunging

Surfacing

Helical Interpolation

M00034122.00 Right4.769.52SDKX 0904-HF LT 3000

M00034132.50 Right5.5612.70SDKX 1205-HF LT 3000

Insert Designation Catalog Nr.Directions R prog.l


Ramping Down

MILLING

279

Cutters

End Mill for SDKX 0904 HF

Shell Mill for SDKX 0904 HF

Screw Coupling for SDKX 0904 HF

Screw:Key:

M2001420M2000602

Screw:Key:

M2001420M2000602

Screw:Key:

M2001420M2000602

Cutter Designation

Cutter Designation

Cutter Designation

LT 902 W-W-D025/2

LT 902 M-W-D042/5

LT 902 S-W-D032/3

LT 902 WL-W-D025/2

LT 902 M-W-D040/5

LT 902 S-W-D025/2

LT 902 WL-W-D032/3

LT 902 M-W-D050/6

LT 902 S-W-D035/4

LT 902 M-W-D063/6*

LT 902 W-W-D032/3

LT 902 M-W-D052/6

LT 902 M-W-D066/6*

Catalog Nr.

Catalog Nr.

Catalog Nr.

M2003351

M2003342

M2003348

M2003350

M2003341

M2003347

M2003352

M2003343

M2003349

M2003345

M2003353

M2003344

M2003346

D

D

D

25

42

32

25

40

25

32

50

35

63

32

52

66

z

z

z

2

5

3

2

5

2

3

6

4

6

3

6

6

Ap

Ap

Ap

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

1.5

D1

D1

D1

9.6

26.6

16.6

9.6

24.6

9.6

16.6

34.6

19.6

47.6

16.6

36.6

50.6

d

d

d

L

L

L1

L1

25

16

M16

25

16

M12

120

40

35

60

200

40

35

60

32

22

M16

22

200

40

35

40

60

32

22

22

120

40

40

60

α Ramp°

α Ramp°

α Ramp°

3.5

0.8

2.0

3.5

0.8

3.5

2.0

0.7

1.5

0.6

2.0

0.7

0.6

d

L1

DD1

Ap

D

D1

d

Ap

L

D1

d

Ap

L1

DD1

SDKX

*On request

MILLING

280

Cutters

End Mill for SDKX 1205 HF

Shell Mill for SDKX 1205 HF

Screw Coupling for SDKX 1205 HF

Screw:Key:

M2000597M2000602

Screw:Key:

M2000597M2000602

Screw:Key:

M2000597M2000602

Cutter Designation

Cutter Designation

Cutter Designation

LT 903 W-W-D032/2

LT 903 M-W-D050/5

LT 903 S-W-D035/2

LT 903 S-W-D042/4*

*On request

LT 903 WL-W-D032/2

LT 903 M-W-D050/4

LT 903 S-W-D032/2

LT 903 M-W-D052/5

LT 903 S-W-D040/4

LT 903 M-W-D063/6

LT 903 M-W-D063/5

LT 903 M-W-D066/6

LT 903 M-W-D080/8

Catalog Nr.

Catalog Nr.

Catalog Nr.

M2003366

M2003357

M2003364

M2003356

M2003365

M2003661

M2003362

M2003358

M2003354

M2003360

M2003662

M2003361

M2003452

D

D

D

32

50

35

42

32

50

32

52

40

63

63

66

80

z

z

z

2

5

2

4

2

4

2

5

4

6

5

6

8

Ap

Ap

Ap

2

2

2

2

2

2

2

2

2

2

2

2

2

D1

D1

D1

11

29

14

21

11

29

11

31

19

42

42

45

59

d

d

d

L

L

L1

L1

32

22

M16

M16

32

22

M16

200

40

35

35

60

200

40

35

60

22

M16

22

40

35

40

22

22

27

40

40

50

α Ramp°

α Ramp°

α Ramp°

2.0

0.8

1.5

0.8

2.0

0.8

2.0

0.8

0.8

0.6

0.6

0.6

0.4

d

L1

DD1

Ap

D

D1

d

Ap

L

D1

d

Ap

L1

DD1

MILLING

281


SDKX 0904 HF – LT 3000














Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

1 125 HB 0.3 1.5 0.30 1.50 190 330 1.0 1.20 250

2 190 HB 0.3 1.5 0.30 1.50 190 300 1.0 1.20 220

3 250 HB 0.3 1.5 0.30 1.50 190 250 1.0 1.20 200

4,6 230 HB 0.3 1.2 0.30 1.36 150 210 0.8 1.00 180

5,7 280 HB 0.3 1.2 0.30 1.36 130 190 0.8 0.90 150

6 180 HB 0.3 1.2 0.30 1.36 150 240 0.8 1.00 200

8 350 HB 0.3 1.2 0.30 1.36 130 170 0.8 0.90 140

10 220 HB 0.3 1.2 0.30 1.20 90 150 0.7 0.80 130

280 HB 0.3 1.1 0.30 1.20 90 130 0.7 0.80 120

320 HB 0.3 1.0 0.30 1.20 60 110 0.7 0.70 100

350 HB 0.3 1.0 0.30 1.20 60 90 0.7 0.70 80

180 HB 0.3 1.3 0.30 0.76 190 250 0.8 0.50 220

240 HB 0.3 1.3 0.30 0.76 160 210 0.8 0.50 190

290 HB 0.3 1.1 0.30 0.46 70 130 0.7 0.30 100

310 HB 0.3 1.1 0.30 0.46 70 120 0.7 0.30 90

12 200 HB 0.3 1.2 0.30 0.52 150 210 0.8 0.40 190

13 42 HRc 0.3 1.0 0.30 0.46 90 150 0.7 0.30 130

150 HB 0.3 1.5 0.30 2.26 150 240 1.2 1.20 200

200 HB 0.3 1.5 0.30 1.50 150 220 1.2 1.20 180

16 250 HB 0.3 1.5 0.30 1.50 150 190 1.2 1.20 160

150 HB 0.3 1.5 0.30 1.36 100 200 1.2 1.00 180

200 HB 0.3 1.5 0.30 1.36 100 180 1.2 1.00 150

18,20 250 HB 0.3 1.5 0.30 1.36 100 150 1.2 1.00 130

31,32 Incoloy 800 240 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 32

33 Inconel 700 250 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 30

34 Stellite 21 350 HB 0.3 1.4 0.30 0.60 30 50 0.8 0.30 30

37 T40 - 0.3 1.5 0.30 0.52 30 60 0.8 0.30 40

36 TiAI6V4 - 0.3 1.4 0.30 0.52 40 70 0.8 0.30 55

45 HRc 0.3 0.6 0.30 0.90 40 80 0.6 0.50 60

50 HRc 0.3 0.5 0.30 0.76 40 70 0.5 0.50 55

55 HRc 0.3 0.5 0.30 0.60 40 60 0.4 0.40 50

40 Ni-Hard 2 400 HB 0.3 0.5 0.30 0.60 40 80 0.4 0.50 50

41 G-X300CrMo15 55 HRc 0.3 0.5 0.30 0.60 30 60 0.4 0.40 40

12 25 AlSi12 130 HB 0.3 1.5 0.30 0.76 200 400 1.5 0.70 280

11

38

17,19

15

14

X100CrMo13, 440C, G-

X260NiCr42

14

11

8GGG40, GGG70,

50005

9

10

6410, X6Cr17, 17-4

PH, 430

7GG20, GG40, EN-GJL-250, N030B

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

3X40CrM0V5, H13, M42, D3, S6-5-2,

12Ni19

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

MILLING

282


SDKX 1205-HF – LT 30 | LT 3000


1 125 HB 0.3 2.0 0.30 3.00 190 330 11.2 22.00 2250

2 190 HB 0.3 2.0 0.30 3.00 190 300 11.2 22.00 2220

3 250 HB 0.3 2.0 0.30 3.00 190 250 11.2 22.00 2200

6 180 HB 0.3 1.6 0.30 2.80 150 240 00.9 11.80 2200

4,6 230 HB 0.3 1.6 0.30 2.80 150 210 00.9 11.80 1180

5,7 280 HB 0.3 1.6 0.30 2.80 130 190 00.9 11.60 1150

8 350 HB 0.3 1.6 0.30 2.50 130 170 00.9 11.60 1140

10 220 HB 0.3 1.6 0.30 2.50 90 150 00.7 11.40 1130

10 280 HB 0.3 1.3 0.30 2.20 90 130 00.7 11.40 1120

11 320 HB 0.3 1.1 0.30 2.00 60 110 00.7 11.20 1100

11 350 HB 0.3 1.1 0.30 1.80 60 90 00.7 11.20 880

14 180 HB 0.3 1.5 0.30 1.10 190 250 00.9 00.90 2220

14 240 HB 0.3 1.5 0.30 1.10 160 210 00.9 00.90 1190

14 290 HB 0.3 1.2 0.30 0.70 70 130 00.8 00.60 1100

14 310 HB 0.3 1.2 0.30 0.70 70 120 00.8 00.60 990

12 200 HB 0.3 1.5 0.30 0.80 150 210 00.9 00.70 1190

13 42 HRc 0.3 1.1 0.30 0.70 90 150 00.8 00.60 1130

15 150 HB 0.3 2.0 0.30 3.00 150 240 11.5 22.00 2200

15 200 HB 0.3 2.0 0.30 3.00 150 220 11.5 22.00 1180

16 250 HB 0.3 2.0 0.30 3.00 150 190 11.5 22.00 1160

17,19 150 HB 0.3 2.0 0.30 2.50 100 200 11.5 11.90 1180

17,19 200 HB 0.3 2.0 0.30 2.50 100 180 11.5 11.90 1150

18,20 250 HB 0.3 2.0 0.30 2.50 100 150 11.5 11.90 1130

31,32 Incoloy 800 240 HB 0.3 1.8 0.30 0.70 25 45 11.0 00.60 332

33 Inconel 700 250 HB 0.3 1.8 0.30 0.60 25 45 11.0 00.60 330

34 Stellite 21 350 HB 0.3 1.8 0.30 0.60 25 45 11.0 00.60 330

36 TiAl6V4 - 0.3 1.8 0.30 0.70 40 65 11.0 00.60 555

37 T40 - 0.3 2.0 0.30 0.60 30 55 11.0 00.60 440

38 45 HRc 0.3 0.8 0.30 1.40 40 80 00.6 11.00 660

38 50 HRc 0.3 0.7 0.30 1.20 40 70 00.5 00.90 555

38 55 HRc 0.3 0.6 0.30 1.00 40 60 00.4 00.80 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 2.0 0.30 1.20 200 400 2.0 1.00 280

GG20, GG40, EN-GJL-250,

No30B

X100CrMo13, 440C,

G-X260NiCr42 11

8GGG40, GGG70,

50005

9

10

7

C35, Ck45, 1020, 1045, 1060, 28Mn6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

2

1














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

283

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S E K N


90°l

mØ d

20°

Fixing,Chipbreaker

s

s ± 0.025For l = 12, d ± 0.08For l = 15, d ± 0.10

m ± 0.013


90°

M0000450

M0000042

M0000041

-

-

-

Neutral

Neutral

Neutral

4.76

4.76

3.18

15.88

12.7

12.7

SEKN 1504 AFTN LT 30





SEKN

MILLING

284

Cutters

Shell Mill for SEKN 1203 AFTN

Screw:Key:

M2000608M2000609

Cutter Designation

LT 550 M-D-D063/5*

LT 550 M-D-D050/4*

LT 550 M-D-D125/7*

LT 550 M-D-D200/10*

LT 550 M-D-D080/6*

LT 550 M-D-D100/6*

LT 550 M-D-D160/7*

LT 550 M-D-D250/13*

Catalog Nr.

M2000564

M2000563

M2000567

M2000569

M2000565

M2000566

M2000568

M2000570

D

76

63

138

213

93

113

173

263

z

5

4

7

10

6

6

7

13

Ap

6

6

6

6

6

6

6

6

D1

63

50

125

200

80

100

160

250

d

22

22

40

60

27

32

40

60

L

48

48

63

63

50

50

63

63

DD1

d

Ap

L

45°

* On request

MILLING

285


SEKN 1203 AFTN – LT 30


1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

286



1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8















Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

287




1 125 HB 0.5 9.0 0.18 0.50 190 330 44.0 0.37 2250

2 190 HB 0.5 9.0 0.18 0.50 190 300 44.0 0.37 2220

3 250 HB 0.5 9.0 0.18 0.50 190 250 44.0 0.37 2200

6 180 HB 0.5 9.0 0.15 0.39 150 240 44.0 0.32 2200

4,6 230 HB 0.5 9.0 0.15 0.39 150 210 44.0 0.32 1180

5,7 280 HB 0.5 9.0 0.15 0.34 130 190 44.0 0.29 1150

8 350 HB 0.5 9.0 0.15 0.34 130 170 44.0 0.29 1140

10 220 HB 0.5 6.4 0.12 0.34 90 150 33.0 0.29 1130

10 280 HB 0.5 6.4 0.12 0.34 90 130 33.0 0.29 1120

11 320 HB 0.5 6.4 0.12 0.28 60 110 33.0 0.26 1100

11 350 HB 0.5 6.4 0.12 0.28 60 90 33.0 0.26 880

14 180 HB 0.5 9.0 0.15 0.34 190 250 44.0 0.29 2220

14 240 HB 0.5 9.0 0.12 0.31 160 210 44.0 0.29 1190

14 290 HB 0.5 6.4 0.12 0.28 70 130 33.0 0.26 1100

14 310 HB 0.5 6.4 0.12 0.28 70 120 33.0 0.26 990

12 200 HB 0.5 9.0 0.15 0.34 150 210 44.0 0.29 1190

13 42 HRc 0.5 6.4 0.15 0.28 90 150 33.0 0.26 1130

15 150 HB 0.5 9.0 0.18 0.50 150 240 44.0 0.37 2200

15 200 HB 0.5 9.0 0.18 0.50 150 220 44.0 0.37 1180

16 250 HB 0.5 9.0 0.18 0.50 150 190 44.0 0.37 1160

17,19 150 HB 0.5 9.0 0.15 0.43 100 200 44.0 0.32 1180

17,19 200 HB 0.5 9.0 0.15 0.43 100 180 44.0 0.32 1150

18,20 250 HB 0.5 9.0 0.15 0.43 100 150 44.0 0.32 1130

31,32 Incoloy 800 240 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 332

33 Inconel 700 250 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 330

34 Stellite 21 350 HB 0.5 6.4 0.12 0.28 25 45 33.0 0.26 330

36 TiAl6V4 - 0.5 6.4 0.12 0.31 40 65 33.0 0.29 555

37 T40 - 0.5 6.4 0.12 0.28 30 55 33.0 0.26 440

38 45 HRc 0.5 3.2 0.10 0.28 40 80 22.0 0.22 660

38 50 HRc 0.5 1.9 0.10 0.25 40 70 11.5 0.21 555

38 55 HRc 0.5 1.6 0.10 0.22 40 60 11.0 0.19 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.18 0.50 200 400 44.0 0.40 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

288

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S E K R

Shape Clearance Angle Insert TypeClamping,

Chipbreaker

s

Toleranced ± 0.08m ± 0.013s ± 0.025

90°l

mØ d

20°


M0000044

M0000043

-

-

Neutral

Neutral

4.76

3.18

12.7

12.7

SEKR 1204 AFTN LT 30

SEKR 1203 AFTN LT 30



MILLING

289

Cutters

Shell Mill for SEKR 1203 AFTN

Screw:Key:

M2000608M2000609

Cutter Designation

LT 550 M-D-D063/5*

LT 550 M-D-D050/4*

LT 550 M-D-D125/7*

LT 550 M-D-D200/10*

LT 550 M-D-D080/6*

LT 550 M-D-D100/6*

LT 550 M-D-D160/7*

LT 550 M-D-D250/13*

Catalog Nr.

M2000564

M2000563

M2000567

M2000569

M2000565

M2000566

M2000568

M2000570

D

76

63

138

213

93

113

173

263

z

5

4

7

10

6

6

7

13

Ap

6

6

6

6

6

6

6

6

D1

63

50

125

200

80

100

160

250

d

22

22

40

60

27

32

40

60

L

48

48

63

63

50

50

63

63

DD1

d

Ap

L

45°

* On request

SEKR

MILLING

290



1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

SEKR 1203 AFTN – LT 30














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

291


SEKR 1204 AFTN – LT 30


1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

292

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S E K T


90°l

mØ d

20°

Fixing,Chipbreaker

s


MILLING

M0000045

M0000455

0.85

1.20

Neutral

Neutral

4.76

3.97

12.70

13.40

SEKT 1204 AFTN LT 30

SEKT 12T3 AGSN LT 30



M0002230

M0002231

0.85

1.20

Neutral

Neutral

4.76

3.97

12.70

13.40

SEKT 1204 AFTN LT 3000

SEKT 12T3 AGSN LT 3000



MILLING

293

Cutters

Shell Mill for SEKT 1204 AFTN

Screw:Key:

M2000599M2000603

Cutter Designation

LT 600 M-W-D050/4

LT 600 M-W-D040/3

LT 600 M-W-D100/6

LT 600 M-D-D160/8

LT 600 M-W-D063/5

LT 600 M-W-D080/6

LT 600 M-W-D125/7

Catalog Nr.

M2000547

M2000546

M2000550

M2000552

M2000548

M2000549

M2000551

D

63

53

113

173

76

93

138

z

4

3

6

8

5

6

7

Ap

6

6

6

6

6

6

6

D1

50

40

100

160

63

80

125

d

22

16

32

40

22

27

40

L

48

40

50

63

48

50

63

Shell Mill for SEKT 12T3 AGSN

Screw:Key:

M2001418M2000602

Cutter Designation

LT 610 M-W-D050/4

LT 610 M-W-D040/3

LT 610 M-W-D100/6

LT 610 M-D-D160/8

LT 610 M-W-D063/5

LT 610 M-W-D080/6

LT 610 M-W-D125/7

Catalog Nr.

M2001382

M2001431

M2001432

M2001434

M2001383

M2001384

M2001433

D

63

53

113

173

76

93

138

z

4

3

6

8

5

6

7

Ap

6

6

6

6

6

6

6

D1

50

40

100

160

63

80

125

d

22

16

32

40

22

27

40

L

48

40

50

63

48

50

63

DD1

d

Ap

L

45°

SEKT

MILLING

294



1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

SEKT 1204 AFTN – LT 30 | LT 3000














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

295



1 125 HB 0.5 7.0 0.18 0.46 190 330 33.0 0.34 2250

2 190 HB 0.5 7.0 0.18 0.46 190 300 33.0 0.34 2220

3 250 HB 0.5 7.0 0.18 0.46 190 250 33.0 0.34 2200

6 180 HB 0.5 7.0 0.15 0.36 150 240 33.0 0.30 2200

4,6 230 HB 0.5 7.0 0.15 0.36 150 210 33.0 0.30 1180

5,7 280 HB 0.5 7.0 0.15 0.32 130 190 33.0 0.27 1150

8 350 HB 0.5 7.0 0.15 0.32 130 170 33.0 0.27 1140

10 220 HB 0.5 5.0 0.12 0.32 90 150 22.3 0.27 1130

10 280 HB 0.5 5.0 0.12 0.32 90 130 22.3 0.27 1120

11 320 HB 0.5 5.0 0.12 0.26 60 110 22.3 0.24 1100

11 350 HB 0.5 5.0 0.12 0.26 60 90 22.3 0.24 880

14 180 HB 0.5 7.0 0.15 0.32 190 250 33.0 0.27 2220

14 240 HB 0.5 7.0 0.12 0.29 160 210 33.0 0.27 1190

14 290 HB 0.5 5.0 0.12 0.26 70 130 22.3 0.24 1100

14 310 HB 0.5 5.0 0.12 0.26 70 120 22.3 0.24 990

12 200 HB 0.5 7.0 0.15 0.32 150 210 33.0 0.27 1190

13 42 HRc 0.5 5.0 0.15 0.26 90 150 22.3 0.24 1130

15 150 HB 0.5 7.0 0.18 0.46 150 240 33.0 0.34 2200

15 200 HB 0.5 7.0 0.18 0.46 150 220 33.0 0.34 1180

16 250 HB 0.5 7.0 0.18 0.46 150 190 33.0 0.34 1160

17,19 150 HB 0.5 7.0 0.15 0.41 100 200 33.0 0.30 1180

17,19 200 HB 0.5 7.0 0.15 0.41 100 180 33.0 0.30 1150

18,20 250 HB 0.5 7.0 0.15 0.41 100 150 33.0 0.30 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.26 25 45 22.3 0.24 330

36 TiAl6V4 - 0.5 5.0 0.12 0.29 40 65 22.3 0.27 555

37 T40 - 0.5 5.0 0.12 0.26 30 55 22.3 0.24 440

38 45 HRc 0.5 2.5 0.10 0.26 40 80 11.5 0.21 660

38 50 HRc 0.5 1.8 0.10 0.23 40 70 11.1 0.19 555

38 55 HRc 0.5 1.5 0.10 0.20 40 60 00.8 0.18 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.46 200 400 33.0 0.37 280

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

SEKT 12T3 AGSN – LT 30 | LT 3000


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

296

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S N K X


90° 0°

Clearance Angle

l

mØ d

Fixing,Chipbreaker

ss


M0003415

M0002237

0.85

0.80

Neutral

Neutral

6.20

7.70

12.70

16.70

SNKX 1205-45 LT 3000

SNKX 1607-45 LT 3000



MILLING

297

Cutters

Shell Mill for SNKX 1205-45°

Screw:Key:

M2003295M2003296

Cutter Designation

LT 946 M-W-D063/6

LT 946 M-W-D100/8

LT 946 M-W-D160/12

LT 946 M-W-D050/4

LT 946 M-W-D080/7

LT 946 M-W-D125/10

Catalog Nr.

M2003224

M2003226

M2003228

M2003223

M2003225

M2003227

D

77

114

174

64

94

139

z

6

8

12

4

7

10

Ap

6

6

6

6

6

6

D1

63

100

160

50

80

125

d

22

32

40

22

27

40

L

48

50

63

48

50

63

DD1

d

Ap

L

45°

Shell Mill for SNKX 1607-45°

Screw:Key:

M2002733M2000603

Cutter Designation

LT 947 M-W-D063/5

LT 947 M-W-D100/7

LT 947 M-W-D200/12*

LT 947 M-W-D050/4

LT 947 M-W-D080/6

LT 947 M-W-D160/10

LT 947 M-W-D125/8

LT 947 M-W-D250/14*

Catalog Nr.

M2002201

M2002203

M2003671

M2002200

M2002202

M2003670

M2002204

M2003672

D

82

119

69

99

144

219

179

269

z

5

7

4

6

8

12

10

14

Ap

7

7

7

7

7

7

7

7

D1

63

100

50

80

125

200

160

250

d

22

32

22

27

40

60

40

60

L

50

63

50

50

63

63

63

63SNKX 45

* On request

MILLING

298


SNKX 1205-45° – LT 3000


1 125 HB 0.5 5.0 0.16 0.34 190 330 33.0 0.30 2250

2 190 HB 0.5 5.0 0.16 0.34 190 300 33.0 0.30 2220

3 250 HB 0.5 5.0 0.16 0.34 190 250 33.0 0.30 2200

6 180 HB 0.5 5.0 0.14 0.28 150 240 33.0 0.26 2200

4,6 230 HB 0.5 5.0 0.14 0.28 150 210 33.0 0.26 1180

5,7 280 HB 0.5 5.0 0.14 0.26 130 190 33.0 0.24 1150

8 350 HB 0.5 5.0 0.14 0.26 130 170 33.0 0.24 1140

10 220 HB 0.5 5.0 0.11 0.28 90 150 33.0 0.26 1130

10 280 HB 0.5 5.0 0.11 0.28 90 130 33.0 0.26 1120

11 320 HB 0.5 5.0 0.11 0.24 60 110 33.0 0.22 1100

11 350 HB 0.5 5.0 0.11 0.24 60 90 33.0 0.22 880

14 180 HB 0.5 5.0 0.14 0.30 190 250 33.0 0.26 2220

14 240 HB 0.5 5.0 0.11 0.30 160 210 33.0 0.26 1190

14 290 HB 0.5 4.0 0.11 0.25 70 130 22.5 0.22 1100

14 310 HB 0.5 4.0 0.11 0.25 70 120 22.5 0.22 990

12 200 HB 0.5 5.0 0.14 0.30 150 210 33.0 0.26 1190

13 42 HRc 0.5 4.0 0.14 0.25 90 150 33.0 0.22 1130

15 150 HB 0.5 5.0 0.17 0.34 150 240 33.0 0.30 2200

15 200 HB 0.5 5.0 0.17 0.34 150 220 33.0 0.30 1180

16 250 HB 0.5 5.0 0.17 0.34 150 190 33.0 0.30 1160

17,19 150 HB 0.5 5.0 0.14 0.30 100 200 33.0 0.27 1180

17,19 200 HB 0.5 5.0 0.14 0.30 100 180 33.0 0.27 1150

18,20 250 HB 0.5 5.0 0.14 0.30 100 150 33.0 0.27 1130

31,32 Incoloy 800 240 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 332

33 Inconel 700 250 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 330

34 Stellite 21 350 HB 0.5 4.0 0.11 0.20 25 45 22.5 0.18 330

36 TiAl6V4 - 0.5 4.0 0.11 0.25 40 65 22.5 0.23 555

37 T40 - 0.5 4.0 0.11 0.23 30 55 22.5 0.20 440

38 45 HRc 0.4 2.0 0.10 0.22 40 80 11.3 0.18 660

38 50 HRc 0.4 2.0 0.10 0.20 40 70 11.3 0.16 555

38 55 HRc 0.4 1.0 0.10 0.18 40 60 11.0 0.15 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 5.0 0.17 0.36 200 400 33.0 0.30 280

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500



Low alloyed 2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

299


SNKX 1607-45° – LT 3000


1 125 HB 0.5 6.5 0.16 0.58 190 330 44.0 0.46 2250

2 190 HB 0.5 6.5 0.16 0.58 190 300 44.0 0.46 2220

3 250 HB 0.5 6.5 0.16 0.58 190 250 44.0 0.46 2200

6 180 HB 0.5 6.5 0.14 0.50 150 240 44.0 0.40 2200

4,6 230 HB 0.5 6.5 0.14 0.50 150 210 44.0 0.40 1180

5,7 280 HB 0.5 6.5 0.14 0.44 130 190 44.0 0.36 1150

8 350 HB 0.5 6.5 0.14 0.44 130 170 44.0 0.36 1140

10 220 HB 0.5 6.5 0.11 0.44 90 150 33.0 0.36 1130

10 280 HB 0.5 6.5 0.11 0.44 90 130 33.0 0.36 1120

11 320 HB 0.5 6.5 0.11 0.36 60 110 33.0 0.32 1100

11 350 HB 0.5 6.5 0.11 0.36 60 90 33.0 0.32 880

14 180 HB 0.5 6.5 0.14 0.44 190 250 44.0 0.34 2220

14 240 HB 0.5 6.5 0.11 0.40 160 210 44.0 0.34 1190

14 290 HB 0.5 5.0 0.11 0.36 70 130 33.0 0.30 1100

14 310 HB 0.5 5.0 0.11 0.36 70 120 33.0 0.30 990

12 200 HB 0.5 6.5 0.14 0.44 150 210 44.0 0.34 1190

13 42 HRc 0.5 5.0 0.14 0.40 90 150 33.0 0.30 1130

15 150 HB 0.5 6.5 0.17 0.58 150 240 44.0 0.46 2200

15 200 HB 0.5 6.5 0.17 0.58 150 220 44.0 0.46 1180

16 250 HB 0.5 6.5 0.17 0.58 150 190 44.0 0.46 1160

17,19 150 HB 0.5 6.5 0.14 0.52 100 200 44.0 0.40 1180

17,19 200 HB 0.5 6.5 0.14 0.52 100 180 44.0 0.40 1150

18,20 250 HB 0.5 6.5 0.14 0.52 100 150 44.0 0.40 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 332

33 Inconel 700 250 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 330

34 Stellite 21 350 HB 0.5 5.0 0.11 0.36 25 45 33.0 0.30 330

36 TiAl6V4 - 0.5 5.0 0.11 0.40 40 65 33.0 0.34 555

37 T40 - 0.5 5.0 0.11 0.36 30 55 33.0 0.30 440

38 45 HRc 0.4 3.0 0.10 0.36 40 80 22.0 0.28 660

38 50 HRc 0.4 3.0 0.10 0.32 40 70 11.5 0.26 555

38 55 HRc 0.4 1.5 0.10 0.28 40 60 11.0 0.24 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 6.5 0.17 0.60 200 400 44.0 0.50 280

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500



Low alloyed 2


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

300

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S N K X


90° 0°

Clearance Angle

l

mØ d

Fixing,Chipbreaker

ss

Copying

Surfacing

Pocket MillingHelical Interpolation

M00021154.20 Right3.719.67SNKX 09T3-HF LT 30



M00022364.20 Right3.719.67SNKX 09T3-HF LT 3000



Ramping Down

MILLING

301

Cutters

d

LL1

DD1

Ap

End Mill for SNKX 09T3-HF

Shell Mill for SNKX 09T3-HF

Screw Coupling for SNKX 09T3-HF

Screw:Key:

M2002101M2002911

Screw:Key:

M2002101M2002911

Screw:Key:

M2002101M2002911

Cutter Designation

Cutter Designation

Cutter Designation

LT 900 M-W-D042/5

LT 900 S-W-D032/4

LT 900 M-W-D040/5

LT 900 S-W-D025/3

LT 900 M-W-D050/6

LT 900 S-W-D035/4

LT 900 M-W-D063/6

LT 900 M-W-D052/6

LT 900 M-W-D066/6

Catalog Nr.

Catalog Nr.

Catalog Nr.

M2002122

M2002129

M2002121

M2002128

M2002123

M2002130

M2002125

M2002124

M2002127

D

D

D

42

32

40

25

50

35

63

52

66

z

z

z

5

4

5

3

6

4

6

6

6

Ap

Ap

Ap

1

1

1

1

1

1

1

1

1

D1

D1

D1

30.5

20.5

28.5

13.5

38.5

23.5

51.5

40.5

54.5

d

d

d

L

L

L1

L1

16

M16

16

M12

40

35

40

35

22

M16

22

40

35

40

22

22

40

40

α Ramp°

α Ramp°

α Ramp°

LT 900 W-W-D032/4 M200211932 4120.5 32 120 60 2.0

LT 900 WL-W-D032/3 M200212032 3120.5 32 200 60 2.0

3.2

2.0

LT 900 W-W-D025/3 M200211825 3113.5 25 120 60 3.5

LT 900 WL-W-D025/2 M200211725 2113.5 25 200 60 3.5

3.5

3.5

2.5

1.5

1.8

2.2

1.7

D

D1

d

Ap

L

d

L

ApL1

DD1

SNKX hf

MILLING

302


SNKX 09T3-HF – LT 30 | LT 3000


1 125 HB 0.1 1.0 0.27 2.10 190 330 00.6 1.10 2250

2 190 HB 0.1 1.0 0.27 1.95 190 300 00.6 1.10 2220

3 250 HB 0.1 1.0 0.27 1.50 190 250 00.6 1.10 2200

6 180 HB 0.1 1.0 0.25 1.95 150 240 00.5 1.00 2200

4,6 230 HB 0.1 1.0 0.25 1.70 150 210 00.5 1.00 1180

5,7 280 HB 0.1 1.0 0.23 1.60 130 190 00.5 0.90 1150

8 350 HB 0.1 1.0 0.23 1.50 130 170 00.5 0.90 1140

10 220 HB 0.1 1.0 0.20 1.70 90 150 00.5 0.90 1130

10 280 HB 0.1 1.0 0.20 1.60 90 130 00.5 0.90 1120

11 320 HB 0.1 0.8 0.20 1.50 60 110 00.4 0.80 1100

11 350 HB 0.1 0.8 0.20 1.40 60 90 00.4 0.80 880

15 150 HB 0.1 1.0 0.20 2.40 150 240 00.6 1.10 2200

15 200 HB 0.1 1.0 0.20 2.40 150 220 00.6 1.10 1180

16 250 HB 0.1 1.0 0.20 2.40 150 190 00.6 1.10 1160

17,19 150 HB 0.1 1.0 0.20 1.80 100 200 00.5 1.00 1180

17,19 200 HB 0.1 1.0 0.20 1.80 100 180 00.5 1.00 1150

18,20 250 HB 0.1 1.0 0.20 1.80 100 150 00.5 1.00 1130

38 45 HRc 0.1 0.6 0.16 1.10 40 80 00.4 0.70 660

38 50 HRc 0.1 0.5 0.16 1.00 40 70 00.3 0.65 555

38 55 HRc 0.1 0.4 0.16 0.90 40 60 00.3 0.60 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020,

1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

303

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S P K Ns

Shape Tolerance

90°

Clearance Angle

l

mØ d

11°

Fixing,Chipbreakerm ± 0.013 s ± 0.025

For l = 12, d ± 0.08For l = 15, d ± 0.10

Surfacing

90°

M0001673

M0000047

M0000046

1.60

1.20

1.20

Right

Right

Right

4.76

4.76

3.21

15.88

12.7

12.7

SPKN 1504 EDTR LT 30





SPKN

MILLING

304

Cutters

Screw:Key: M2000609

M2000606

Shell Mill for SPKN 1203 EDTR

Cutter Designation

LT 750 M-D-D080/5*

LT 750 M-D-D063/4*

LT 750 M-D-D160/10*

LT 750 M-D-D250/14*

LT 750 M-D-D100/7*

LT 750 M-D-D125/8*

LT 750 M-D-D200/12*

Catalog Nr.

M2000572

M2000571

M2000576

M2000578

M2000574

M2000575

M2000577

D

86

69

166

256

106

131

206

z

5

4

10

14

7

8

12

Ap

9

9

9

9

9

9

9

D1

80

63

160

250

100

125

200

d

27

22

40

63

32

40

63

L

50

40

63

63

50

63

63

DD1

d

Ap

L

75°

* On request

MILLING

305


SPKN 1203 EDTR – LT 30


1 125 HB 0.5 7.0 0.18 0.43 190 330 33.0 0.30 2250

2 190 HB 0.5 7.0 0.18 0.43 190 300 33.0 0.30 2220

3 250 HB 0.5 7.0 0.18 0.43 190 250 33.0 0.30 2200

6 180 HB 0.5 7.0 0.15 0.34 150 240 33.0 0.26 2200

4,6 230 HB 0.5 7.0 0.15 0.34 150 210 33.0 0.26 1180

5,7 280 HB 0.5 7.0 0.15 0.30 130 190 33.0 0.23 1150

8 350 HB 0.5 7.0 0.15 0.30 130 170 33.0 0.23 1140

10 220 HB 0.5 5.0 0.12 0.30 90 150 22.3 0.23 1130

10 280 HB 0.5 5.0 0.12 0.30 90 130 22.3 0.23 1120

11 320 HB 0.5 5.0 0.12 0.24 60 110 22.3 0.21 1100

11 350 HB 0.5 5.0 0.12 0.24 60 90 22.3 0.21 880

15 150 HB 0.5 7.0 0.18 0.43 150 240 33.0 0.30 2200

15 200 HB 0.5 7.0 0.18 0.43 150 220 33.0 0.30 1180

16 250 HB 0.5 7.0 0.18 0.43 150 190 33.0 0.30 1160

17,19 150 HB 0.5 7.0 0.15 0.38 100 200 33.0 0.26 1180

17,19 200 HB 0.5 7.0 0.15 0.38 100 180 33.0 0.26 1150

18,20 250 HB 0.5 7.0 0.15 0.38 100 150 33.0 0.26 1130

38 45 HRc 0.5 2.5 0.10 0.24 40 80 11.5 0.18 660

38 50 HRc 0.5 1.8 0.10 0.22 40 70 11.1 0.17 555

38 55 HRc 0.5 1.5 0.10 0.19 40 60 00.8 0.16 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

MILLING

306




1 125 HB 0.5 7.0 0.18 0.43 190 330 33.0 0.30 2250

2 190 HB 0.5 7.0 0.18 0.43 190 300 33.0 0.30 2220

3 250 HB 0.5 7.0 0.18 0.43 190 250 33.0 0.30 2200

6 180 HB 0.5 7.0 0.15 0.34 150 240 33.0 0.26 2200

4,6 230 HB 0.5 7.0 0.15 0.34 150 210 33.0 0.26 1180

5,7 280 HB 0.5 7.0 0.15 0.30 130 190 33.0 0.23 1150

8 350 HB 0.5 7.0 0.15 0.30 130 170 33.0 0.23 1140

10 220 HB 0.5 5.0 0.12 0.30 90 150 22.3 0.23 1130

10 280 HB 0.5 5.0 0.12 0.30 90 130 22.3 0.23 1120

11 320 HB 0.5 5.0 0.12 0.24 60 110 22.3 0.21 1100

11 350 HB 0.5 5.0 0.12 0.24 60 90 22.3 0.21 880

15 150 HB 0.5 7.0 0.18 0.43 150 240 33.0 0.30 2200

15 200 HB 0.5 7.0 0.18 0.43 150 220 33.0 0.30 1180

16 250 HB 0.5 7.0 0.18 0.43 150 190 33.0 0.30 1160

17,19 150 HB 0.5 7.0 0.15 0.38 100 200 33.0 0.26 1180

17,19 200 HB 0.5 7.0 0.15 0.38 100 180 33.0 0.26 1150

18,20 250 HB 0.5 7.0 0.15 0.38 100 150 33.0 0.26 1130

38 45 HRc 0.5 2.5 0.10 0.24 40 80 11.5 0.18 660

38 50 HRc 0.5 1.8 0.10 0.22 40 70 11.1 0.17 555

38 55 HRc 0.5 1.5 0.10 0.19 40 60 00.8 0.16 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

MILLING

307




1 125 HB 0.5 9.0 0.18 0.43 190 330 44.0 0.30 2250

2 190 HB 0.5 9.0 0.18 0.43 190 300 44.0 0.30 2220

3 250 HB 0.5 9.0 0.18 0.43 190 250 44.0 0.30 2200

6 180 HB 0.5 9.0 0.15 0.34 150 240 44.0 0.26 2200

4,6 230 HB 0.5 9.0 0.15 0.34 150 210 44.0 0.26 1180

5,7 280 HB 0.5 9.0 0.15 0.30 130 190 44.0 0.23 1150

8 350 HB 0.5 9.0 0.15 0.30 130 170 44.0 0.23 1140

10 220 HB 0.5 6.5 0.12 0.30 90 150 33.0 0.23 1130

10 280 HB 0.5 6.5 0.12 0.30 90 130 33.0 0.23 1120

11 320 HB 0.5 6.5 0.12 0.24 60 110 33.0 0.21 1100

11 350 HB 0.5 6.5 0.12 0.24 60 90 33.0 0.21 880

15 150 HB 0.5 9.0 0.18 0.43 150 240 44.0 0.30 2200

15 200 HB 0.5 9.0 0.18 0.43 150 220 44.0 0.30 1180

16 250 HB 0.5 9.0 0.18 0.43 150 190 44.0 0.30 1160

17,19 150 HB 0.5 9.0 0.15 0.38 100 200 44.0 0.26 1180

17,19 200 HB 0.5 9.0 0.15 0.38 100 180 44.0 0.26 1150

18,20 250 HB 0.5 9.0 0.15 0.38 100 150 44.0 0.26 1130

38 45 HRc 0.5 3.2 0.10 0.24 40 80 22.0 0.18 660

38 50 HRc 0.5 2.3 0.10 0.22 40 70 11.5 0.17 555

38 55 HRc 0.5 1.9 0.10 0.19 40 60 11.0 0.16 550



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

308

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S P K R


90°

Clearance Angle

l

mØ d

11°

Fixing,Chipbreaker

s

Surfacing

MILLING

90°

M0000049

M0000048

1.20

1.20

Right

Right

4.76

3.21

12.70

12.70

SPKR 1204 EDTR LT 30

SPKR 1203 EDTR LT 30



MILLING

309

Cutters

Shell Mill for SPKR 1203 EDTR

Cutter Designation

LT 750 M-D-D080/5*

LT 750 M-D-D063/4*

LT 750 M-D-D160/10*

LT 750 M-D-D250/14*

LT 750 M-D-D100/7*

LT 750 M-D-D125/8*

LT 750 M-D-D200/12*

Catalog Nr.

M2000572

M2000571

M2000576

M2000578

M2000574

M2000575

M2000577

D

86

69

166

256

106

131

206

z

5

4

10

14

7

8

12

Ap

9

9

9

9

9

9

9

D1

80

63

160

250

100

125

200

d

27

22

40

63

32

40

63

L

50

40

63

63

50

63

63

DD1

d

Ap

L

75°

* On request

SPKR

Screw:Key:

M2000606M2000609

MILLING

310


SPKR 1203 EDTR – LT 30


1 125 HB 0.5 7.0 0.18 0.38 190 330 33.0 0.26 2250

2 190 HB 0.5 7.0 0.18 0.38 190 300 33.0 0.26 2220

3 250 HB 0.5 7.0 0.18 0.38 190 250 33.0 0.26 2200

6 180 HB 0.5 7.0 0.15 0.30 150 240 33.0 0.23 2200

4,6 230 HB 0.5 7.0 0.15 0.30 150 210 33.0 0.23 1180

5,7 280 HB 0.5 7.0 0.15 0.26 130 190 33.0 0.21 1150

8 350 HB 0.5 7.0 0.15 0.26 130 170 33.0 0.21 1140

10 220 HB 0.5 5.0 0.12 0.26 90 150 22.3 0.21 1130

10 280 HB 0.5 5.0 0.12 0.26 90 130 22.3 0.21 1120

11 320 HB 0.5 5.0 0.12 0.22 60 110 22.3 0.18 1100

11 350 HB 0.5 5.0 0.12 0.22 60 90 22.3 0.18 880

14 180 HB 0.5 7.0 0.15 0.26 190 250 33.0 0.21 2220

14 240 HB 0.5 7.0 0.12 0.24 160 210 33.0 0.21 1190

14 290 HB 0.5 5.0 0.12 0.22 70 130 22.3 0.18 1100

14 310 HB 0.5 5.0 0.12 0.22 70 120 22.3 0.18 990

12 200 HB 0.5 7.0 0.15 0.26 150 210 33.0 0.21 1190

13 42 HRc 0.5 5.0 0.15 0.22 90 150 22.3 0.18 1130

15 150 HB 0.5 7.0 0.18 0.38 150 240 33.0 0.26 2200

15 200 HB 0.5 7.0 0.18 0.38 150 220 33.0 0.26 1180

16 250 HB 0.5 7.0 0.18 0.38 150 190 33.0 0.26 1160

17,19 150 HB 0.5 7.0 0.15 0.34 100 200 33.0 0.23 1180

17,19 200 HB 0.5 7.0 0.15 0.34 100 180 33.0 0.23 1150

18,20 250 HB 0.5 7.0 0.15 0.34 100 150 33.0 0.23 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330

36 TiAl6V4 - 0.5 5.0 0.12 0.24 40 65 22.3 0.21 555

37 T40 - 0.5 5.0 0.12 0.22 30 55 22.3 0.18 440

38 45 HRc 0.5 2.5 0.10 0.22 40 80 11.5 0.16 660

38 50 HRc 0.5 1.8 0.10 0.19 40 70 11.1 0.15 555

38 55 HRc 0.5 1.5 0.10 0.17 40 60 00.8 0.14 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.38 200 400 33.0 0.29 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

311


SPKR 1204 EDTR – LT 30


1 125 HB 0.5 7.0 0.18 0.38 190 330 33.0 0.26 2250

2 190 HB 0.5 7.0 0.18 0.38 190 300 33.0 0.26 2220

3 250 HB 0.5 7.0 0.18 0.38 190 250 33.0 0.26 2200

6 180 HB 0.5 7.0 0.15 0.30 150 240 33.0 0.23 2200

4,6 230 HB 0.5 7.0 0.15 0.30 150 210 33.0 0.23 1180

5,7 280 HB 0.5 7.0 0.15 0.26 130 190 33.0 0.21 1150

8 350 HB 0.5 7.0 0.15 0.26 130 170 33.0 0.21 1140

10 220 HB 0.5 5.0 0.12 0.26 90 150 22.3 0.21 1130

10 280 HB 0.5 5.0 0.12 0.26 90 130 22.3 0.21 1120

11 320 HB 0.5 5.0 0.12 0.22 60 110 22.3 0.18 1100

11 350 HB 0.5 5.0 0.12 0.22 60 90 22.3 0.18 880

14 180 HB 0.5 7.0 0.15 0.26 190 250 33.0 0.21 2220

14 240 HB 0.5 7.0 0.12 0.24 160 210 33.0 0.21 1190

14 290 HB 0.5 5.0 0.12 0.22 70 130 22.3 0.18 1100

14 310 HB 0.5 5.0 0.12 0.22 70 120 22.3 0.18 990

12 200 HB 0.5 7.0 0.15 0.26 150 210 33.0 0.21 1190

13 42 HRc 0.5 5.0 0.15 0.22 90 150 22.3 0.18 1130

15 150 HB 0.5 7.0 0.18 0.38 150 240 33.0 0.26 2200

15 200 HB 0.5 7.0 0.18 0.38 150 220 33.0 0.26 1180

16 250 HB 0.5 7.0 0.18 0.38 150 190 33.0 0.26 1160

17,19 150 HB 0.5 7.0 0.15 0.34 100 200 33.0 0.23 1180

17,19 200 HB 0.5 7.0 0.15 0.34 100 180 33.0 0.23 1150

18,20 250 HB 0.5 7.0 0.15 0.34 100 150 33.0 0.23 1130

31,32 Incoloy 800 240 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 332

33 Inconel 700 250 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330

34 Stellite 21 350 HB 0.5 5.0 0.12 0.22 25 45 22.3 0.18 330

36 TiAl6V4 - 0.5 5.0 0.12 0.24 40 65 22.3 0.21 555

37 T40 - 0.5 5.0 0.12 0.22 30 55 22.3 0.18 440

38 45 HRc 0.5 2.5 0.10 0.22 40 80 11.5 0.16 660

38 50 HRc 0.5 1.8 0.10 0.19 40 70 11.1 0.15 555

38 55 HRc 0.5 1.5 0.10 0.17 40 60 00.8 0.14 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 7.0 0.18 0.38 200 400 33.0 0.29 280

X100CrMo13, 440C,

G-X260NiCr42 Steel

11

GGG40, GGG70, 50005

Fe, Ni & Co based

9

Ti based 10


No30B


42CrMo4, St50, Ck60, 4140, 4340,

100Cr6



X5CrNi18-9


S31500



Low alloyed 2


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

312

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S P M T


90°

Clearance Angle

l

mØ d

11°

Fixing,Chipbreaker

s


MILLING

M00030630.80 Neutral3.719.53SPMT 09T308 TN LT 30

M00031050.80 Neutral4.8012.70SPMT 120408 TN LT 30


M00012260.80 Neutral3.9713.29SPMT 12T308 LT 30



M00034170.80 Neutral3.719.53SPMT 09T308 TN LT 3000



M00034200.80 Neutral3.9713.29SPMT 12T308 LT 3000



MILLING

313


SPMT 060304 TN – LT 30 | LT 3000

SPMT


1 125 HB 0.3 6.0 0.06 0.12 190 330 22.4 0.10 2250

2 190 HB 0.3 6.0 0.06 0.10 190 300 22.4 0.08 2220

3 250 HB 0.3 6.0 0.06 0.10 190 250 22.4 0.08 2200

6 180 HB 0.3 6.0 0.06 0.12 150 240 22.4 0.10 2200

4,6 230 HB 0.3 6.0 0.06 0.10 150 210 22.4 0.08 1180

5,7 280 HB 0.3 6.0 0.05 0.10 130 190 22.4 0.08 1150

8 350 HB 0.3 6.0 0.05 0.10 130 170 22.4 0.08 1140

10 220 HB 0.3 4.3 0.06 0.08 90 150 11.8 0.07 1130

10 280 HB 0.3 4.3 0.05 0.10 90 130 11.8 0.08 1120

11 320 HB 0.3 4.3 0.05 0.08 60 110 11.8 0.06 1100

11 350 HB 0.3 4.3 0.05 0.08 60 90 11.8 0.06 880

14 180 HB 0.3 6.0 0.06 0.08 190 250 22.4 0.07 2220

14 240 HB 0.3 6.0 0.05 0.08 160 210 22.4 0.07 1190

14 290 HB 0.3 4.3 0.05 0.08 70 130 11.8 0.07 1100

14 310 HB 0.3 4.3 0.05 0.07 70 120 11.8 0.06 990

12 200 HB 0.3 6.0 0.05 0.08 150 210 22.4 0.07 1190

13 42 HRc 0.3 4.3 0.05 0.07 90 150 11.8 0.06 1130

15 150 HB 0.3 6.0 0.05 0.14 150 240 22.4 0.12 2200

15 200 HB 0.3 6.0 0.05 0.12 150 220 22.4 0.10 1180

16 250 HB 0.3 6.0 0.05 0.12 150 190 22.4 0.10 1160

17,19 150 HB 0.3 6.0 0.05 0.14 100 200 22.4 0.12 1180

17,19 200 HB 0.3 6.0 0.05 0.12 100 180 22.4 0.10 1150

18,20 250 HB 0.3 6.0 0.05 0.12 100 150 22.4 0.10 1130

31,32 Incoloy 800 240 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 332

33 Inconel 700 250 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 330

34 Stellite 21 350 HB 0.3 4.3 0.04 0.08 25 45 11.8 0.06 330

36 TiAl6V4 - 0.3 4.3 0.04 0.08 40 65 11.8 0.06 555

37 T40 - 0.3 4.3 0.04 0.08 30 55 11.8 0.06 440

38 45 HRc 0.3 2.1 0.04 0.10 40 80 11.2 0.08 660

38 50 HRc 0.3 1.3 0.04 0.08 40 70 00.9 0.06 555

38 55 HRc 0.3 0.9 0.04 0.06 40 60 00.6 0.05 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.3 6.0 0.08 0.14 200 400 2.4 0.12 280

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

314


SPMT 09T308 TN – LT 30 | LT 3000


1 125 HB 0.5 9.0 0.07 0.17 190 330 22.4 0.15 2250

2 190 HB 0.5 9.0 0.06 0.15 190 300 22.4 0.13 2220

3 250 HB 0.5 9.0 0.06 0.15 190 250 22.4 0.13 2200

6 180 HB 0.5 9.0 0.07 0.17 150 240 22.4 0.15 2200

4,6 230 HB 0.5 9.0 0.06 0.15 150 210 22.4 0.13 1180

5,7 280 HB 0.5 9.0 0.05 0.13 130 190 22.4 0.11 1150

8 350 HB 0.5 9.0 0.05 0.13 130 170 22.4 0.11 1140

10 220 HB 0.5 6.5 0.07 0.15 90 150 11.8 0.13 1130

10 280 HB 0.5 6.5 0.05 0.13 90 130 11.8 0.11 1120

11 320 HB 0.5 6.5 0.05 0.10 60 110 11.8 0.08 1100

11 350 HB 0.5 6.5 0.05 0.10 60 90 11.8 0.08 880

14 180 HB 0.5 9.0 0.07 0.12 190 250 22.4 0.10 2220

14 240 HB 0.5 9.0 0.05 0.10 160 210 22.4 0.08 1190

14 290 HB 0.5 6.5 0.05 0.10 70 130 11.8 0.08 1100

14 310 HB 0.5 6.5 0.05 0.08 70 120 11.8 0.07 990

12 200 HB 0.5 9.0 0.05 0.08 150 210 22.4 0.07 1190

13 42 HRc 0.5 6.5 0.05 0.08 90 150 11.8 0.07 1130

15 150 HB 0.5 9.0 0.06 0.22 150 240 22.4 0.18 2200

15 200 HB 0.5 9.0 0.06 0.22 150 220 22.4 0.18 1180

16 250 HB 0.5 9.0 0.06 0.20 150 190 22.4 0.16 1160

17,19 150 HB 0.5 9.0 0.06 0.22 100 200 22.4 0.18 1180

17,19 200 HB 0.5 9.0 0.05 0.22 100 180 22.4 0.18 1150

18,20 250 HB 0.5 9.0 0.05 0.20 100 150 22.4 0.16 1130

31,32 Incoloy 800 240 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 332

33 Inconel 700 250 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 330

34 Stellite 21 350 HB 0.5 6.5 0.04 0.12 25 45 11.8 0.10 330

36 TiAl6V4 - 0.5 6.5 0.04 0.12 40 65 11.8 0.10 555

37 T40 - 0.5 6.5 0.04 0.12 30 55 11.8 0.10 440

38 45 HRc 0.5 3.2 0.04 0.12 40 80 11.2 0.10 660

38 50 HRc 0.5 1.9 0.04 0.10 40 70 00.9 0.08 555

38 55 HRc 0.5 1.3 0.04 0.08 40 60 00.6 0.06 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.08 0.16 200 400 2.4 0.13 280

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

315


SPMT 120408 TN – LT 30 | LT 3000


1 125 HB 0.5 9.0 0.13 0.29 190 330 33.0 0.18 2250

2 190 HB 0.5 9.0 0.13 0.29 190 300 33.0 0.18 2220

3 250 HB 0.5 9.0 0.13 0.29 190 250 33.0 0.18 2200

6 180 HB 0.5 9.0 0.11 0.23 150 240 33.0 0.16 2200

4,6 230 HB 0.5 9.0 0.11 0.23 150 210 33.0 0.16 1180

5,7 280 HB 0.5 9.0 0.11 0.20 130 190 33.0 0.14 1150

8 350 HB 0.5 9.0 0.11 0.20 130 170 33.0 0.14 1140

10 220 HB 0.5 6.5 0.08 0.20 90 150 22.3 0.14 1130

10 280 HB 0.5 6.5 0.08 0.20 90 130 22.3 0.14 1120

11 320 HB 0.5 6.5 0.08 0.16 60 110 22.3 0.13 1100

11 350 HB 0.5 6.5 0.08 0.16 60 90 22.3 0.13 880

14 180 HB 0.5 9.0 0.11 0.23 190 250 33.0 0.16 2220

14 240 HB 0.5 9.0 0.08 0.20 160 210 33.0 0.16 1190

14 290 HB 0.5 6.5 0.08 0.16 70 130 22.3 0.13 1100

14 310 HB 0.5 6.5 0.08 0.16 70 120 22.3 0.13 990

12 200 HB 0.5 9.0 0.11 0.23 150 210 33.0 0.16 1190

13 42 HRc 0.5 6.5 0.11 0.18 90 150 22.3 0.13 1130

15 150 HB 0.5 9.0 0.13 0.29 150 240 33.0 0.18 2200

15 200 HB 0.5 9.0 0.13 0.29 150 220 33.0 0.18 1180

16 250 HB 0.5 9.0 0.13 0.29 150 190 33.0 0.18 1160

17,19 150 HB 0.5 9.0 0.11 0.25 100 200 33.0 0.16 1180

17,19 200 HB 0.5 9.0 0.11 0.25 100 180 33.0 0.16 1150

18,20 250 HB 0.5 9.0 0.11 0.25 100 150 33.0 0.16 1130

31,32 Incoloy 800 240 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 332

33 Inconel 700 250 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 330

34 Stellite 21 350 HB 0.5 6.5 0.08 0.16 25 45 22.3 0.13 330

36 TiAl6V4 - 0.5 6.5 0.08 0.18 40 65 22.3 0.14 555

37 T40 - 0.5 6.5 0.08 0.16 30 55 22.3 0.13 440

38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.5 0.11 660

38 50 HRc 0.5 1.9 0.07 0.14 40 70 11.1 0.10 555

38 55 HRc 0.5 1.0 0.07 0.13 40 60 00.8 0.10 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.29 200 400 3.0 0.20 280

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

316


SPMT 12T308 – LT 30 | LT 3000


1 125 HB 0.5 9.0 0.13 0.29 190 330 33.0 00.18 2250

2 190 HB 0.5 9.0 0.13 0.29 190 300 33.0 00.18 2220

3 250 HB 0.5 9.0 0.13 0.29 190 250 33.0 00.18 2200

6 180 HB 0.5 9.0 0.11 0.23 150 240 33.0 00.16 2200

4,6 230 HB 0.5 9.0 0.11 0.23 150 210 33.0 00.16 1180

5,7 280 HB 0.5 9.0 0.11 0.20 130 190 33.0 00.14 1150

8 350 HB 0.5 9.0 0.11 0.20 130 170 33.0 00.14 1140

10 220 HB 0.5 6.5 0.08 0.20 90 150 22.3 00.14 1130

10 280 HB 0.5 6.5 0.08 0.20 90 130 22.3 00.14 1120

11 320 HB 0.5 6.5 0.08 0.16 60 110 22.3 00.13 1100

11 350 HB 0.5 6.5 0.08 0.16 60 90 22.3 00.13 880

14 180 HB 0.5 9.0 0.11 0.23 190 250 33.0 00.16 2220

14 240 HB 0.5 9.0 0.08 0.20 160 210 33.0 00.16 1190

14 290 HB 0.5 6.5 0.08 0.16 70 130 22.3 00.13 1100

14 310 HB 0.5 6.5 0.08 0.16 70 120 22.3 00.13 990

12 200 HB 0.5 9.0 0.11 0.23 150 210 33.0 00.16 1190

13 42 HRc 0.5 6.5 0.11 0.18 90 150 22.3 00.13 1130

15 150 HB 0.5 9.0 0.13 0.29 150 240 33.0 00.18 2200

15 200 HB 0.5 9.0 0.13 0.29 150 220 33.0 00.18 1180

16 250 HB 0.5 9.0 0.13 0.29 150 190 33.0 00.18 1160

17,19 150 HB 0.5 9.0 0.11 0.25 100 200 33.0 00.16 1180

17,19 200 HB 0.5 9.0 0.11 0.25 100 180 33.0 00.16 1150

18,20 250 HB 0.5 9.0 0.11 0.25 100 150 33.0 00.16 1130

31,32 Incoloy 800 240 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 332

33 Inconel 700 250 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 330

34 Stellite 21 350 HB 0.5 6.5 0.08 0.16 25 45 22.3 00.13 330

36 TiAl6V4 - 0.5 6.5 0.08 0.18 40 65 22.3 00.14 555

37 T40 - 0.5 6.5 0.08 0.16 30 55 22.3 00.13 440

38 45 HRc 0.5 3.2 0.07 0.16 40 80 11.5 00.11 660

38 50 HRc 0.5 1.9 0.07 0.14 40 70 11.1 00.10 555

38 55 HRc 0.5 1.0 0.07 0.13 40 60 00.8 00.10 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 9.0 0.13 0.29 200 400 3.0 0.20 280

1C35, Ck45, 1020,

1045, 1060, 28Mn6

242CrMo4, St50,

Ck60, 4140, 4340, 100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316, X5CrNi18-

9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

317

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S P U Ns


90°

Clearance Angle

l

mØ d

11°

Fixing,Chipbreaker


90°

M00000500.80 Neutral3.1812.7SPUN 120308 LT 30



SPUN

MILLING

318


SPUN 120308 – LT 30


1 125 HB 0.5 7.0 0.18 0.37 190 330 33.0 00.26 2250

2 190 HB 0.5 7.0 0.18 0.37 190 300 33.0 00.26 2220

3 250 HB 0.5 7.0 0.18 0.37 190 250 33.0 00.26 2200

6 180 HB 0.5 7.0 0.15 0.29 150 240 33.0 00.23 2200

4,6 230 HB 0.5 7.0 0.15 0.29 150 210 33.0 00.23 1180

5,7 280 HB 0.5 7.0 0.15 0.25 130 190 33.0 00.21 1150

8 350 HB 0.5 7.0 0.15 0.25 130 170 33.0 00.21 1140

10 220 HB 0.5 5.0 0.12 0.25 90 150 22.3 00.21 1130

10 280 HB 0.5 5.0 0.12 0.25 90 130 22.3 00.21 1120

11 320 HB 0.5 5.0 0.12 0.21 60 110 22.3 00.18 1100

11 350 HB 0.5 5.0 0.12 0.21 60 90 22.3 00.18 880

15 150 HB 0.5 7.0 0.18 0.37 150 240 33.0 00.26 2200

15 200 HB 0.5 7.0 0.18 0.37 150 220 33.0 00.26 1180

16 250 HB 0.5 7.0 0.18 0.37 150 190 33.0 00.26 1160

17,19 150 HB 0.5 7.0 0.15 0.32 100 200 33.0 00.23 1180

17,19 200 HB 0.5 7.0 0.15 0.32 100 180 33.0 00.23 1150

18,20 250 HB 0.5 7.0 0.15 0.32 100 150 33.0 00.23 1130

38 45 HRc 0.5 2.5 0.10 0.21 40 80 11.5 00.16 660

38 50 HRc 0.5 1.8 0.10 0.18 40 70 11.1 00.15 555

38 55 HRc 0.5 1.5 0.10 0.16 40 60 00.8 00.14 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

319

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


T P K N


11°

Fixing,Chipbreaker

60°

m ± 0.013 s ± 0.025For l = 16, d ± 0.05For l = 22, d ± 0.08

sl

mØ d


11°60°

M0000052

M0000051

1.20

1.20

Right

Right

4.76

3.18

19.92

14.52

TPKN 2204 PDTR LT 30

TPKN 1603 PDTR LT 30



TPKN

MILLING

320

Cutters

Shell Mill for TPKN 1603 PDTR

Cutter Designation

LT 310 M-D-D080/5*

LT 310 M-D-D063/4*

LT 310 M-D-D100/6*

LT 310 M-D-D125/6*

Catalog Nr.

M2000700

M2000699

M2000701

M2000702

D

80

63

100

125

z

5

4

6

6

Ap

13

13

13

13

d

27

22

32

40

L

50

50

50

63

D

d

Ap

L

90°

Shell Mill for TPKN 2204 PDTR

Cutter Designation

LT 320 M-D-D100/5*

LT 320 M-D-D080/4*

LT 320 M-D-D125/6*

LT 320 M-D-D160/7*

Catalog Nr.

M2000704

M2000703

M2000705

M2000706

D

100

80

125

160

z

5

4

6

7

Ap

18

18

18

18

d

32

27

40

40

L

50

50

63

63

* On request

* On request

Screw:Key:

M2002952M2000609

Screw:Key:

M2002951M2000609

MILLING

321


TPKN 1603 PDTR – LT 30


1 125 HB 0.5 12.0 0.14 0.27 190 330 33.0 0.20 2250

2 190 HB 0.5 12.0 0.14 0.27 190 300 33.0 0.20 2220

3 250 HB 0.5 12.0 0.14 0.27 190 250 33.0 0.20 2200

6 180 HB 0.5 12.0 0.12 0.21 150 240 33.0 0.17 2200

4,6 230 HB 0.5 12.0 0.12 0.21 150 210 33.0 0.17 1180

5,7 280 HB 0.5 12.0 0.12 0.19 130 190 33.0 0.15 1150

8 350 HB 0.5 12.0 0.12 0.19 130 170 33.0 0.15 1140

10 220 HB 0.5 8.6 0.10 0.19 90 150 22.3 0.15 1130

10 280 HB 0.5 8.6 0.10 0.19 90 130 22.3 0.15 1120

11 320 HB 0.5 8.6 0.10 0.15 60 110 22.3 0.14 1100

11 350 HB 0.5 8.6 0.10 0.15 60 90 22.3 0.14 880

15 150 HB 0.5 12.0 0.14 0.27 150 240 33.0 0.20 2200

15 200 HB 0.5 12.0 0.14 0.27 150 220 33.0 0.20 1180

16 250 HB 0.5 12.0 0.14 0.27 150 190 33.0 0.20 1160

17,19 150 HB 0.5 12.0 0.12 0.24 100 200 33.0 0.17 1180

17,19 200 HB 0.5 12.0 0.12 0.24 100 180 33.0 0.17 1150

18,20 250 HB 0.5 12.0 0.12 0.24 100 150 33.0 0.17 1130

38 45 HRc 0.5 4.3 0.08 0.15 40 80 11.5 0.12 660

38 50 HRc 0.5 3.0 0.08 0.14 40 70 11.1 0.11 555

38 55 HRc 0.5 2.6 0.08 0.12 40 60 00.8 0.10 550



1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

MILLING

322


TPKN 2204 PDTR – LT 30


1 125 HB 0.5 18.0 0.16 0.27 190 330 44.0 00.19 2250

2 190 HB 0.5 18.0 0.16 0.27 190 300 44.0 00.19 2220

3 250 HB 0.5 18.0 0.16 0.27 190 250 44.0 00.19 2200

6 180 HB 0.5 18.0 0.14 0.21 150 240 44.0 00.17 2200

4,6 230 HB 0.5 18.0 0.14 0.21 150 210 44.0 00.17 1180

5,7 280 HB 0.5 18.0 0.14 0.19 130 190 44.0 00.15 1150

8 350 HB 0.5 18.0 0.14 0.19 130 170 44.0 00.15 1140

10 220 HB 0.5 12.9 0.11 0.19 90 150 33.0 00.15 1130

10 280 HB 0.5 12.9 0.11 0.19 90 130 33.0 00.15 1120

11 320 HB 0.5 12.9 0.11 0.15 60 110 33.0 00.13 1100

11 350 HB 0.5 12.9 0.11 0.15 60 90 33.0 00.13 880

15 150 HB 0.5 18.0 0.16 0.27 150 240 44.0 00.19 2200

15 200 HB 0.5 18.0 0.16 0.27 150 220 44.0 00.19 1180

16 250 HB 0.5 18.0 0.16 0.27 150 190 44.0 00.19 1160

17,19 150 HB 0.5 18.0 0.14 0.24 100 200 44.0 00.17 1180

17,19 200 HB 0.5 18.0 0.14 0.24 100 180 44.0 00.17 1150

18,20 250 HB 0.5 18.0 0.14 0.24 100 150 44.0 00.17 1130

38 45 HRc 0.5 6.4 0.09 0.15 40 80 22.0 00.12 660

38 50 HRc 0.5 4.5 0.09 0.14 40 70 11.5 00.11 555

38 55 HRc 0.5 3.9 0.09 0.12 40 60 11.0 00.10 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

323

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


T P K R


11°

Fixing,Chipbreaker

s

60°

m ± 0.013 s ± 0.025For l = 16, d ± 0.05For l = 22, d ± 0.08

l

mØ d


1160°



M0000983

M0000053

1.20

1.20

Right

Right

4.76

3.18

19.92

14.52

TPKR 2204 PDTR LT 30

TPKR 1603 PDTR LT 30

TPKR

MILLING

324

Cutters

Shell Mill for TPKR 1603 PDTR

Cutter Designation

LT 310 M-D-D080/5*

LT 310 M-D-D063/4*

LT 310 M-D-D100/6*

LT 310 M-D-D125/6*

Catalog Nr.

M2000700

M2000699

M2000701

M2000702

D

80

63

100

125

z

5

4

6

6

Ap

13

13

13

13

d

27

22

32

40

L

50

50

50

63

D

d

Ap

L

90°

D

d

9

Shell Mill for TPKR 2204 PDTR

Cutter Designation

LT 320 M-D-D100/5*

LT 320 M-D-D080/4*

LT 320 M-D-D125/6*

LT 320 M-D-D160/7*

Catalog Nr.

M2000704

M2000703

M2000705

M2000706

D

100

80

125

160

z

5

4

6

7

Ap

18

18

18

18

d

32

27

40

40

L

50

50

63

63

* On request

* On request

Screw:Key:

M2002952M2000609

Screw:Key:

M2002951M2000609

MILLING

325


TPKR 1603 PDTR – LT 30


1 125 HB 0.5 12.0 0.13 0.22 190 330 33.0 0.17 2250

2 190 HB 0.5 12.0 0.13 0.22 190 300 33.0 0.17 2220

3 250 HB 0.5 12.0 0.13 0.22 190 250 33.0 0.17 2200

6 180 HB 0.5 12.0 0.11 0.18 150 240 33.0 0.15 2200

4,6 230 HB 0.5 12.0 0.11 0.18 150 210 33.0 0.15 1180

5,7 280 HB 0.5 12.0 0.11 0.15 130 190 33.0 0.13 1150

8 350 HB 0.5 12.0 0.11 0.15 130 170 33.0 0.13 1140

10 220 HB 0.5 8.6 0.08 0.15 90 150 22.3 0.13 1130

10 280 HB 0.5 8.6 0.08 0.15 90 130 22.3 0.13 1120

11 320 HB 0.5 8.6 0.08 0.13 60 110 22.3 0.12 1100

11 350 HB 0.5 8.6 0.08 0.13 60 90 22.3 0.12 880

14 180 HB 0.5 12.0 0.11 0.15 190 250 33.0 0.13 2220

14 240 HB 0.5 12.0 0.08 0.14 160 210 33.0 0.13 1190

14 290 HB 0.5 8.6 0.08 0.13 70 130 22.3 0.12 1100

14 310 HB 0.5 8.6 0.08 0.13 70 120 22.3 0.12 990

12 200 HB 0.5 12.0 0.11 0.15 150 210 33.0 0.13 1190

13 42 HRc 0.5 8.6 0.11 0.13 90 150 22.3 0.12 1130

15 150 HB 0.5 12.0 0.13 0.22 150 240 33.0 0.17 2200

15 200 HB 0.5 12.0 0.13 0.22 150 220 33.0 0.17 1180

16 250 HB 0.5 12.0 0.13 0.22 150 190 33.0 0.17 1160

17,19 150 HB 0.5 12.0 0.11 0.20 100 200 33.0 0.15 1180

17,19 200 HB 0.5 12.0 0.11 0.20 100 180 33.0 0.15 1150

18,20 250 HB 0.5 12.0 0.11 0.20 100 150 33.0 0.15 1130

31,32 Incoloy 800 240 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 332

33 Inconel 700 250 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 330

34 Stellite 21 350 HB 0.5 8.6 0.08 0.13 25 45 22.3 0.12 330

36 TiAl6V4 - 0.5 8.6 0.08 0.14 40 65 22.3 0.13 555

37 T40 - 0.5 8.6 0.08 0.13 30 55 22.3 0.12 440

38 45 HRc 0.5 4.3 0.07 0.13 40 80 11.5 0.10 660

38 50 HRc 0.5 3.0 0.07 0.11 40 70 11.1 0.09 555

38 55 HRc 0.5 2.6 0.07 0.10 40 60 00.8 0.09 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 12.0 0.13 0.22 200 400 3.0 0.18 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8


GroupMaterial

ExemplesHardness


Parameters















Non-alloyed

Stee

l Low alloyed

High Alloyed

Stai

nles

s St

eel High Alloyed

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co based

Ti based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

MILLING

326


TPKR 2204 PDTR – LT 30


1 125 HB 0.5 18.0 0.13 0.22 190 330 44.0 00.17 2250

2 190 HB 0.5 18.0 0.13 0.22 190 300 44.0 00.17 2220

3 250 HB 0.5 18.0 0.13 0.22 190 250 44.0 00.17 2200

6 180 HB 0.5 18.0 0.11 0.18 150 240 44.0 00.15 2200

4,6 230 HB 0.5 18.0 0.11 0.18 150 210 44.0 00.15 1180

5,7 280 HB 0.5 18.0 0.11 0.15 130 190 44.0 00.13 1150

8 350 HB 0.5 18.0 0.11 0.15 130 170 44.0 00.13 1140

10 220 HB 0.5 12.9 0.08 0.15 90 150 33.0 00.13 1130

10 280 HB 0.5 12.9 0.08 0.15 90 130 33.0 00.13 1120

11 320 HB 0.5 12.9 0.08 0.13 60 110 33.0 00.12 1100

11 350 HB 0.5 12.9 0.08 0.13 60 90 33.0 00.12 880

14 180 HB 0.5 18.0 0.11 0.15 190 250 44.0 00.13 2220

14 240 HB 0.5 18.0 0.08 0.14 160 210 44.0 00.13 1190

14 290 HB 0.5 12.9 0.08 0.13 70 130 33.0 00.12 1100

14 310 HB 0.5 12.9 0.08 0.13 70 120 33.0 00.12 990

12 200 HB 0.5 18.0 0.11 0.15 150 210 44.0 00.13 1190

13 42 HRc 0.5 12.9 0.11 0.13 90 150 33.0 00.12 1130

15 150 HB 0.5 18.0 0.13 0.22 150 240 44.0 00.17 2200

15 200 HB 0.5 18.0 0.13 0.22 150 220 44.0 00.17 1180

16 250 HB 0.5 18.0 0.13 0.22 150 190 44.0 00.17 1160

17,19 150 HB 0.5 18.0 0.11 0.20 100 200 44.0 00.15 1180

17,19 200 HB 0.5 18.0 0.11 0.20 100 180 44.0 00.15 1150

18,20 250 HB 0.5 18.0 0.11 0.20 100 150 44.0 00.15 1130

31,32 Incoloy 800 240 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 332

33 Inconel 700 250 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 330

34 Stellite 21 350 HB 0.5 12.9 0.08 0.13 25 45 33.0 00.12 330

36 TiAl6V4 - 0.5 12.9 0.08 0.14 40 65 33.0 00.13 555

37 T40 - 0.5 12.9 0.08 0.13 30 55 33.0 00.12 440

38 45 HRc 0.5 6.4 0.07 0.13 40 80 22.0 00.10 660

38 50 HRc 0.5 4.5 0.07 0.11 40 70 11.5 00.09 555

38 55 HRc 0.5 3.9 0.07 0.10 40 60 11.0 00.09 550



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.5 18.0 0.13 0.22 200 400 4.0 0.18 280

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

327

MILLING

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


T P U N

Shape Clearance Angled ± 0.08m ± 0.13s ± 0.13

Tolerance

11°

sl

mØ d

Fixing,Chipbreaker

60°


11°60°

M00000540.80 Right3.1813.49TPUN 160308 LT 30



TPUN

MILLING

328

Cutters

Shell Mill for TPUN1603 PDTR

Cutter Designation

LT 310 M-D-D100/6*

LT 310 M-D-D125/6*

Catalog Nr.

M2000700

M2000699

M2000701

M2000702

LT 310 M-D-D080/5*

LT 310 M-D-D063/4*

D

80

63

100

125

z

5

4

6

6

Ap

13

13

13

13

d

27

22

32

40

L

50

50

50

63

D

d

Ap

L

90°

* On request Screw:Key:

M2002951M2000609

MILLING

329


TPUN 160308 NN PDTR – LT 30


1 125 HB 0.5 12.0 0.14 0.27 190 330 33.0 0.20 2250

2 190 HB 0.5 12.0 0.14 0.27 190 300 33.0 0.20 2220

3 250 HB 0.5 12.0 0.14 0.27 190 250 33.0 0.20 2200

6 180 HB 0.5 12.0 0.12 0.21 150 240 33.0 0.17 2200

4,6 230 HB 0.5 12.0 0.12 0.21 150 210 33.0 0.17 1180

5,7 280 HB 0.5 12.0 0.12 0.19 130 190 33.0 0.15 1150

8 350 HB 0.5 12.0 0.12 0.19 130 170 33.0 0.15 1140

10 220 HB 0.5 8.6 0.10 0.19 90 150 22.3 0.15 1130

10 280 HB 0.5 8.6 0.10 0.19 90 130 22.3 0.15 1120

11 320 HB 0.5 8.6 0.10 0.15 60 110 22.3 0.14 1100

11 350 HB 0.5 8.6 0.10 0.15 60 90 22.3 0.14 880

15 150 HB 0.5 12.0 0.14 0.27 150 240 33.0 0.20 2200

15 200 HB 0.5 12.0 0.14 0.27 150 220 33.0 0.20 1180

16 250 HB 0.5 12.0 0.14 0.27 150 190 33.0 0.20 1160

17,19 150 HB 0.5 12.0 0.12 0.24 100 200 33.0 0.17 1180

17,19 200 HB 0.5 12.0 0.12 0.24 100 180 33.0 0.17 1150

18,20 250 HB 0.5 12.0 0.12 0.24 100 150 33.0 0.17 1130

38 45 HRc 0.5 4.3 0.08 0.15 40 80 11.5 0.12 660

38 50 HRc 0.5 3.0 0.08 0.14 40 70 11.1 0.11 555

38 55 HRc 0.5 2.6 0.08 0.12 40 60 00.8 0.10 550



X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

8

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2














Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

ALU-MILLING

330

ALU-MILLING

331


LT 05ALU-MILLING

APGT

ALU-MILLING

332

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


A P G T11°


l

d ± 0.025m ± 0.025s ± 0.13

Ø d

s

m

Tolerance

Shoulder Mill SurfacingSlotting

M0003089

M0001010

0.40

0.80

Right

Right

3.52

4.89

10.80

16.40

APGT 100304 PDER-ALU LT05

APGT 160408 PDER-ALU LT05


LT 05

ALU-MILLING

333


APGT 100304 PDER-ALU – LT 05

APGT 160408 PDER-ALU – LT 05


Si < 4 % 60 HB 0.3 9.0 0.12 0.20 400 1200 33.0 0.14 5500

4% < Si < 8 % 100 HB 0.3 9.0 0.10 0.18 250 600 33.0 0.14 4400

Copper Alloys 14 26,27,28 CuZn30 100 HB 0.3 9.0 0.10 0.18 100 800 33.0 0.14 3300

29 Fiber Plastics - 0.3 9.0 0.12 0.20 80 500 33.0 0.12 2200

30 Hard Rubber - 0.3 9.0 0.12 0.20 80 300 33.0 0.12 1150

- Graphite - 0.3 9.0 0.12 0.20 100 200 33.0 0.12 1150

36 Ti 1 - 0.3 5.0 0.08 0.20 35 60 22.0 0.12 445

37 TiAl 6 V4 - 0.3 5.0 0.08 0.15 28 45 22.0 0.12 335

15

10

1321, 22 23, 24


Si < 4 % 60 HB 0.5 15.0 0.15 0.32 400 1200 44.0 0.16 5500

4% < Si < 8 % 100 HB 0.5 15.0 0.13 0.29 250 600 44.0 0.16 4400

Copper Alloys 14 26,27,28 CuZn30 100 HB 0.5 15.0 0.13 0.29 100 800 44.0 0.16 3300

29 Fiber Plastics - 0.5 15.0 0.15 0.32 80 500 44.0 0.14 2200

30 Hard Rubber - 0.5 15.0 0.15 0.32 80 300 44.0 0.14 1150

- Graphite - 0.5 15.0 0.15 0.32 100 200 44.0 0.14 1150

36 Ti 1 - 0.5 15.0 0.10 0.32 35 60 44.0 0.14 445

37 TiAl 6 V4 - 0.5 15.0 0.10 0.24 28 45 44.0 0.14 335

15

10

1321, 22 23, 24














H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic














H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

ALU-MILLING

334

FProductivity

1, 2, 3, 46, 7, 8, 1110, 125, 9

NoNoYesYesCoolant

Stainless Steel

VC


S E G T

Shape Clearance Angles

d ± 0.025m ± 0.025s ± 0.13

90° 20°l

mØ d

Fixing,Chipbreaker

Tolerance

Surfacing

ALU-MILLING

90°

M00010080.84 Neutral4.7912.70SEGT 1204 AFEN-ALU LT05


LT 05

Chamfering

ALU-MILLING

335


SEGT 1204 AFEN-ALU – LT 05


Si < 4 % 60 HB 0.3 9.0 0.12 0.35 400 1200 33.0 0.25 5500

4% < Si < 8 % 100 HB 0.3 9.0 0.10 0.35 250 600 33.0 0.25 4400

Cooper Alloys 14 26,27,28 CuZn30 100 HB 0.3 9.0 0.10 0.35 100 800 33.0 0.25 3300

29 Fiber Plastics - 0.3 9.0 0.12 0.35 80 500 33.0 0.20 2200

30 Hard Rubber - 0.3 9.0 0.12 0.35 80 300 33.0 0.20 1150

- Graphite - 0.3 9.0 0.12 0.35 100 200 33.0 0.20 1150

36 Ti 1 - 0.3 5.0 0.08 0.35 35 60 22.0 0.20 445

37 TiAl 6 V4 - 0.3 5.0 0.08 0.28 28 45 22.0 0.20 335

1321, 22 23, 24

15

10

SEGT














H.T.

A

Ti Based Alloys

NF

Al (<8%Si)

Copper Alloys

Non-Metallic

336

DRILLING

337

DRILLING

LT 30DRILLING

SPMG

338

DRILLING

S P M Gl


11°

Tolerance d ± 0.05m ± 0.08s ± 0.13

90° Ø dm

Fixing,Chipbreaker

s

M3003882

M3002914

M3003883

M3002913

M3002915

0.40

0.80

0.80

0.40

0.80

Neutral

Neutral

Neutral

Neutral

Neutral

2.38

3.97

4.76

2.38

4.76

5.0

7.94

11.50

6.0

9.80

SPMG 050204 NN LT 30

SPMG 07T308 NN LT 30






339

DRILLING

108

110

113

113

115

115

119

121

32

34

36

36

38

38

40

42

M2003247

M2003248

M2003695

M2003249

M2003696

M2003250

M2003251

M2003252

124

127

131

131

134

134

139

142

48

51

54

54

57

57

60

63

M2003266

M2003267

M2003700

M2003268

M2003701

M2003269

M2003270

M2003271

94

L

L

L

94

96

96

99

99

26

L1

L1

L1

26

28

28

30

30

M2003704

Catalog Nr

Catalog Nr

Catalog Nr

M2003705

M2003706

M2003707

M2003708

M2003709

2xD

2xD

2xD

107 39 M2003718

L

L

L

L1

L1

L1

Catalog Nr

Catalog Nr

Catalog Nr

107 39 M2003719

110 42 M2003720

110 42 M2003721

114 45 M2003722

114 45 M2003723

3xD

3xD

3xD

123

131

134

137

139

141

141

44

46

48

50

52

54

54

M2003253

M2003255

M2003256

M2003257

M2003258

M2003698

M2003259

145

154

158

162

165

168

168

66

69

72

75

78

81

81

M2003272

M2003273

M2003274

M2003275

M2003276

M2003702

M2003277

LT DR160 S06-_D 16.0 25

LT DR170 S06-_D 17.0 25

LT DR175 S06-_D 17.5 25

LT DR180 S06-_D 18.0 25

LT DR185 S06-_D 18.5 25

LT DR190 S06-_D 19.0 25

LT DR200 S06-_D 20.0 25

LT DR210 S06-_D 21.0 25

Insert SPMG 060204

LT DR125 S05-_D

Drill Body Designation



LT DR130 S05-_D

LT DR135 S05-_D

LT DR140 S05-_D

LT DR145 S05-_D

LT DR150 S05-_D

12.5

D

D

D

13.0

13.5

14.0

14.5

15.0

20

d

d

d

20

20

20

20

20

Insert SPMG 050204 **

LT DR220 S07-_D

LT DR230 S07-_D

LT DR240 S07-_D

LT DR250 S07-_D

LT DR260 S07-_D

LT DR265 S07-_D

LT DR270 S07-_D

22.0

23.0

24.0

25.0

26.0

26.5

27.0

25

32

32

32

32

32

32

Insert SPMG 07T308

Screw: M2003824

Screw: M2003823

Screw: M2003820

** 4D for SPMG 050204 and 110408 also available on request

D

L1

L

d D

L1

340

DRILLING

Drill Body Designation D d

Insert SPMG 110408 **

LT DR350 S11-_D

LT DR360 S11-_D

LT DR370 S11-_D

LT DR380 S11-_D

LT DR390 S11-_D

LT DR400 S11-_D

LT DR410 S11-_D

LT DR340 S11-_D

35.0

36.0

37.0

38.0

39.0

40.0

41.0

34.0

40

40

40

40

40

40

40

40

L L1 Catalog Nr

174

177

180

183

185

188

191

171

70

72

74

76

78

80

82

68

M2003711

M2003712

M2003713

M2003714

M2003715

M2003716

M2003717

M2003710

L L1 Catalog Nr

209

213

217

221

224

228

232

105

108

111

114

117

120

123

M2003725

M2003726

M2003727

M2003728

M2003729

M2003730

M2003731

205 102 M2003724

Drill Body Designation D d L L1 Catalog Nr

2xD

2xD*

L L1 Catalog Nr

3xD

3xD

LT DR280 S09-_D

LT DR290 S09-_D

LT DR295 S09-_D

LT DR300 S09-_D

LT DR310 S09-_D

LT DR320 S09-_D

LT DR330 S09-_D

28.0

29.0

29.5

30.0

31.0

32.0

33.0

32

32

32

32

32

32

32

144

146

151

151

154

156

159

56

58

60

60

62

64

66

M2003260

M2003261

M2003699

M2003262

M2003263

M2003264

M2003265

172

175

181

181

185

188

192

84

87

90

90

93

96

99

M2003278

M2003280

M2003703

M2003281

M2003282

M2003283

M2003284

Insert SPMG 090408

Screw: M2003821

* Available on request** 4D for SPMG 050204 and 110408 also available on request

D

L1

L

d D

L1

Screw: M2003822

341

DRILLINGMachining Conditions

SPMG 050204 NN – LT 30


1 125 HB 0.04 0.09 180 270 00.07 225

2 190 HB 0.04 0.09 180 230 00.07 205

3 250 HB 0.04 0.09 180 200 00.07 190

6 180 HB 0.04 0.09 120 230 00.07 175

4,6 230 HB 0.04 0.09 120 190 00.05 155

5,7 280 HB 0.04 0.09 100 170 00.04 135

8 350 HB 0.04 0.09 100 150 00.04 125

10 220 HB 0.05 0.09 70 170 00.07 120

10 280 HB 0.05 0.09 70 150 00.07 110

11 320 HB 0.05 0.08 60 130 00.07 95

11 350 HB 0.05 0.08 60 100 00.07 80

14 180 HB 0.04 0.09 170 230 00.06 200

14 240 HB 0.05 0.09 120 210 00.07 165

14 290 HB 0.05 0.08 70 120 00.07 95

14 310 HB 0.05 0.08 70 120 00.07 95

12 200 HB 0.05 0.08 100 150 00.07 125

13 42 HRc 0.04 0.07 60 100 00.05 80

15 150 HB 0.07 0.09 150 230 00.08 190

15 200 HB 0.07 0.09 150 210 00.08 180

16 250 HB 0.07 0.09 150 170 00.08 160

17,19 150 HB 0.07 0.09 120 200 00.08 160

17,19 200 HB 0.07 0.09 120 170 00.08 145

18,20 250 HB 0.07 0.09 120 150 00.08 135

31,32 Incoloy 800 240 HB 0.04 0.07 25 35 00.05 30

33 Inconel 700 250 HB 0.04 0.07 25 35 00.05 30

34 Stellite 21 350 HB 0.04 0.07 23 35 00.07 29

36 TiAl6V4 - 0.04 0.07 35 60 00.05 48

37 T40 - 0.04 0.07 28 40 00.05 34

38 45 HRc 0.04 0.07 50 90 00.05 70

38 50 HRc 0.04 0.07 40 70 00.05 55

38 55 HRc 0.04 0.07 30 60 00.05 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.09 200 400 00.07 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

342

DRILLING

342


SPMG 060204 NN – LT 30


1 125 HB 0.04 0.09 180 270 00.07 225

2 190 HB 0.04 0.09 180 230 00.07 205

3 250 HB 0.04 0.09 180 200 00.07 190

6 180 HB 0.04 0.09 120 230 00.07 175

4,6 230 HB 0.04 0.09 120 190 00.07 155

5,7 280 HB 0.04 0.09 100 170 00.06 135

8 350 HB 0.04 0.09 100 150 00.06 125

10 220 HB 0.05 0.09 70 170 00.07 120

10 280 HB 0.05 0.09 70 150 00.07 110

11 320 HB 0.05 0.08 60 130 00.07 95

11 350 HB 0.05 0.08 60 100 00.07 80

14 180 HB 0.04 0.09 170 230 00.06 200

14 240 HB 0.05 0.09 120 210 00.07 165

14 290 HB 0.05 0.08 70 120 00.07 95

14 310 HB 0.05 0.08 70 120 00.07 95

12 200 HB 0.05 0.08 100 150 00.07 125

13 42 HRc 0.04 0.07 60 100 00.05 80

15 150 HB 0.07 0.10 150 230 00.09 190

15 200 HB 0.07 0.10 150 210 00.09 180

16 250 HB 0.07 0.10 150 170 00.09 160

17,19 150 HB 0.07 0.10 120 200 00.09 160

17,19 200 HB 0.07 0.10 120 170 00.09 145

18,20 250 HB 0.07 0.10 120 150 00.09 135

31,32 Incoloy 800 240 HB 0.04 0.07 25 35 00.05 30

33 Inconel 700 250 HB 0.04 0.07 25 35 00.05 30

34 Stellite 21 350 HB 0.04 0.07 23 35 00.05 29

36 TiAl6V4 - 0.04 0.07 35 60 00.05 45

37 T40 - 0.04 0.07 28 40 00.05 34

38 45 HRc 0.04 0.07 50 90 00.05 70

38 50 HRc 0.04 0.07 40 70 00.05 55

38 55 HRc 0.04 0.07 30 60 00.05 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.04 0.09 200 400 00.07 300

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

343


SPMG 07T308 NN – LT 30


1 125 HB 0.05 0.10 180 270 00.08 225

2 190 HB 0.05 0.10 180 230 00.08 205

3 250 HB 0.05 0.10 180 200 00.08 190

6 180 HB 0.05 0.10 120 230 00.08 175

4,6 230 HB 0.05 0.10 120 190 00.08 155

5,7 280 HB 0.05 0.10 100 170 00.07 135

8 350 HB 0.05 0.10 100 150 00.07 125

10 220 HB 0.07 0.10 70 170 00.09 120

10 280 HB 0.07 0.10 70 150 00.09 110

11 320 HB 0.07 0.09 60 130 00.08 95

11 350 HB 0.07 0.09 60 100 00.08 80

14 180 HB 0.05 0.10 170 230 00.07 200

14 240 HB 0.07 0.10 120 210 00.08 165

14 290 HB 0.07 0.09 70 120 00.08 95

14 310 HB 0.07 0.09 70 120 00.08 95

12 200 HB 0.07 0.09 100 150 00.08 125

13 42 HRc 0.05 0.08 60 100 00.07 80

15 150 HB 0.10 0.11 150 230 00.11 190

15 200 HB 0.10 0.11 150 210 00.11 180

16 250 HB 0.10 0.11 150 170 00.11 160

17,19 150 HB 0.10 0.11 120 200 00.11 160

17,19 200 HB 0.10 0.11 120 170 00.11 145

18,20 250 HB 0.10 0.11 120 150 00.11 135

31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30

33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30

34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29

36 TiAl6V4 - 0.05 0.08 35 60 00.07 45

37 T40 - 0.05 0.08 28 40 00.07 34

38 45 HRc 0.05 0.08 50 90 00.07 70

38 50 HRc 0.05 0.08 40 70 00.07 55

38 55 HRc 0.05 0.08 30 60 00.07 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 200 400 00.08 300

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

344

DRILLING

344


SPMG 090408 NN – LT 30


1 125 HB 0.06 0.11 180 270 00.09 225

2 190 HB 0.06 0.11 180 230 00.09 205

3 250 HB 0.06 0.11 180 200 00.09 190

6 180 HB 0.06 0.11 120 230 00.09 175

4,6 230 HB 0.06 0.11 120 190 00.09 155

5,7 280 HB 0.06 0.11 100 170 00.08 135

8 350 HB 0.06 0.11 100 150 00.08 125

10 220 HB 0.09 0.11 70 170 00.10 120

10 280 HB 0.09 0.11 70 150 00.10 110

11 320 HB 0.09 0.10 60 130 00.09 95

11 350 HB 0.09 0.10 60 100 00.09 80

14 180 HB 0.06 0.11 170 230 00.08 200

14 240 HB 0.09 0.11 120 210 00.10 165

14 290 HB 0.09 0.10 70 120 00.09 95

14 310 HB 0.09 0.10 70 120 00.09 95

12 200 HB 0.09 0.10 100 150 00.09 125

13 42 HRc 0.06 0.09 60 100 00.08 80

15 150 HB 0.10 0.12 150 230 00.11 190

15 200 HB 0.10 0.12 150 210 00.11 180

16 250 HB 0.10 0.12 150 170 00.11 160

17,19 150 HB 0.10 0.12 120 200 00.11 160

17,19 200 HB 0.10 0.12 120 170 00.11 145

18,20 250 HB 0.10 0.12 120 150 00.11 135

31,32 Incoloy 800 240 HB 0.06 0.09 25 35 00.08 30

33 Inconel 700 250 HB 0.06 0.09 25 35 00.08 30

34 Stellite 21 350 HB 0.06 0.09 23 35 00.08 29

36 TiAl6V4 - 0.06 0.09 35 60 00.08 45

37 T40 - 0.06 0.09 28 40 00.08 34

38 45 HRc 0.06 0.09 50 90 00.08 70

38 50 HRc 0.06 0.09 40 70 00.08 55

38 55 HRc 0.06 0.09 30 60 00.08 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

345


SPMG 110408 NN – LT 30


1 125 HB 0.08 0.14 180 270 00.11 225

2 190 HB 0.08 0.14 180 230 00.11 205

3 250 HB 0.08 0.14 180 200 00.11 190

6 180 HB 0.07 0.14 120 230 00.11 175

4,6 230 HB 0.07 0.14 120 190 00.07 155

5,7 280 HB 0.07 0.14 100 170 00.07 135

8 350 HB 0.07 0.12 100 150 00.07 125

10 220 HB 0.07 0.12 70 170 00.10 120

10 280 HB 0.07 0.12 70 150 00.10 110

11 320 HB 0.07 0.11 60 130 00.09 95

11 350 HB 0.07 0.10 60 100 00.08 80

14 180 HB 0.06 0.11 170 230 00.08 200

14 240 HB 0.09 0.11 120 210 00.10 165

14 290 HB 0.06 0.10 70 120 00.08 95

14 310 HB 0.06 0.09 70 120 00.08 95

12 200 HB 0.09 0.10 100 150 00.09 125

13 42 HRc 0.06 0.09 60 100 00.08 80

15 150 HB 0.10 0.15 150 230 00.13 190

15 200 HB 0.10 0.15 150 210 00.13 180

16 250 HB 0.10 0.15 150 170 00.13 160

17,19 150 HB 0.10 0.15 120 200 00.13 160

17,19 200 HB 0.10 0.14 120 170 00.12 145

18,20 250 HB 0.10 0.14 120 150 00.12 135

31,32 Incoloy 800 240 HB 0.06 0.10 25 35 00.08 30

33 Inconel 700 250 HB 0.06 0.10 25 35 00.08 30

34 Stellite 21 350 HB 0.06 0.10 23 35 00.10 29

36 TiAl6V4 - 0.06 0.09 35 60 00.08 48

37 T40 - 0.06 0.09 28 40 00.08 34

38 45 HRc 0.06 0.09 50 90 00.08 70

38 50 HRc 0.06 0.09 40 70 00.08 55

38 55 HRc 0.06 0.09 30 60 00.08 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

346

DRILLING

W C M X


80° m

l

Ø d7°

Fixing,Chipbreaker

s ± 0.13For l = 04/05/06, d ± 0.05 m ± 0.08For l = 08, d ± 0.08 m ± 0.13

s

M3001122

M3000953

M3001121

M3000954

0.80

0.80

0.80

1.20

Neutral

Neutral

Neutral

Neutral

2.38

3.97

3.18

4.76

4.00

6.00

5.00

8.00

WCMX 040208 NN LT 30

WCMX 06T308 NN LT 30





347


WCMX

WCMX 040208 NN – LT 30


1 125 HB 0.05 0.10 180 270 00.08 225

2 190 HB 0.05 0.10 180 230 00.08 205

3 250 HB 0.05 0.10 180 200 00.08 190

6 180 HB 0.05 0.10 120 230 00.08 175

4,6 230 HB 0.05 0.10 120 190 00.08 155

5,7 280 HB 0.05 0.10 100 170 00.07 135

8 350 HB 0.05 0.10 100 150 00.07 125

10 220 HB 0.07 0.10 70 170 00.09 120

10 280 HB 0.07 0.10 70 150 00.09 110

11 320 HB 0.07 0.09 60 130 00.08 95

11 350 HB 0.07 0.09 60 100 00.08 80

14 180 HB 0.05 0.10 170 230 00.07 200

14 240 HB 0.07 0.10 120 210 00.08 165

14 290 HB 0.07 0.09 70 120 00.08 95

14 310 HB 0.07 0.09 70 120 00.08 95

12 200 HB 0.07 0.09 100 150 00.08 125

13 42 HRc 0.05 0.08 60 100 00.07 80

15 150 HB 0.09 0.11 150 230 00.10 190

15 200 HB 0.09 0.11 150 210 00.10 180

16 250 HB 0.09 0.11 150 170 00.10 160

17,19 150 HB 0.09 0.11 120 200 00.10 160

17,19 200 HB 0.09 0.11 120 170 00.10 145

18,20 250 HB 0.09 0.11 120 150 00.10 135

31,32 Incoloy 800 240 HB 0.05 0.08 25 35 00.07 30

33 Inconel 700 250 HB 0.05 0.08 25 35 00.07 30

34 Stellite 21 350 HB 0.05 0.08 23 35 00.07 29

36 TiAl6V4 - 0.05 0.08 35 60 00.07 45

37 T40 - 0.05 0.08 28 40 00.07 34

38 45 HRc 0.05 0.08 50 90 00.07 70

38 50 HRc 0.05 0.08 40 70 00.07 55

38 55 HRc 0.05 0.08 30 60 00.07 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.05 0.10 200 400 00.08 300

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

348

DRILLING

348


WCMX 050308 NN – LT 30


1 125 HB 0.06 0.11 180 270 00.09 225

2 190 HB 0.06 0.11 180 230 00.09 205

3 250 HB 0.06 0.11 180 200 00.09 190

6 180 HB 0.06 0.11 120 230 00.09 175

4,6 230 HB 0.06 0.11 120 190 00.09 155

5,7 280 HB 0.06 0.11 100 170 00.08 135

8 350 HB 0.06 0.11 100 150 00.08 125

10 220 HB 0.09 0.11 70 170 00.10 120

10 280 HB 0.09 0.11 70 150 00.10 110

11 320 HB 0.09 0.10 60 130 00.09 95

11 350 HB 0.09 0.10 60 100 00.09 80

14 180 HB 0.06 0.11 170 230 00.08 200

14 240 HB 0.09 0.11 120 210 00.10 165

14 290 HB 0.09 0.10 70 120 00.09 95

14 310 HB 0.09 0.10 70 120 00.09 95

12 200 HB 0.09 0.10 100 150 00.09 125

13 42 HRc 0.06 0.09 60 100 00.08 80

15 150 HB 0.09 0.12 150 230 00.11 190

15 200 HB 0.09 0.12 150 210 00.11 180

16 250 HB 0.09 0.12 150 170 00.11 160

17,19 150 HB 0.09 0.12 120 200 00.11 160

17,19 200 HB 0.09 0.12 120 170 00.11 145

18,20 250 HB 0.09 0.12 120 150 00.11 135

31,32 Incoloy 800 240 HB 0.06 0.09 25 35 00.08 30

33 Inconel 700 250 HB 0.06 0.09 25 35 00.08 30

34 Stellite 21 350 HB 0.06 0.09 23 35 00.08 29

36 TiAl6V4 - 0.06 0.09 35 60 00.08 45

37 T40 - 0.06 0.09 28 40 00.08 34

38 45 HRc 0.06 0.09 50 90 00.08 70

38 50 HRc 0.06 0.09 40 70 00.08 55

38 55 HRc 0.06 0.09 30 60 00.08 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.06 0.11 200 400 00.09 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

349


WCMX 06T308 NN – LT 30


1 125 HB 0.06 0.12 180 270 00.09 225

2 190 HB 0.06 0.12 180 230 00.09 205

3 250 HB 0.06 0.12 180 200 00.09 190

6 180 HB 0.06 0.12 120 230 00.09 175

4,6 230 HB 0.06 0.12 120 190 00.09 155

5,7 280 HB 0.06 0.12 100 170 00.09 135

8 350 HB 0.06 0.12 100 150 00.09 125

10 220 HB 0.08 0.12 70 170 00.10 120

10 280 HB 0.08 0.12 70 150 00.10 110

11 320 HB 0.08 0.11 60 130 00.09 95

11 350 HB 0.08 0.11 60 100 00.09 80

14 180 HB 0.06 0.12 170 230 00.09 200

14 240 HB 0.08 0.12 120 210 00.10 165

14 290 HB 0.08 0.11 70 120 00.09 95

14 310 HB 0.08 0.11 70 120 00.09 95

12 200 HB 0.08 0.11 100 150 00.09 125

13 42 HRc 0.06 0.10 60 100 00.08 80

15 150 HB 0.09 0.13 150 230 00.11 190

15 200 HB 0.09 0.13 150 210 00.11 180

16 250 HB 0.09 0.13 150 170 00.11 160

17,19 150 HB 0.09 0.13 120 200 00.11 160

17,19 200 HB 0.09 0.13 120 170 00.11 145

18,20 250 HB 0.09 0.13 120 150 00.11 135

31,32 Incoloy 800 240 HB 0.06 0.10 25 35 00.08 30

33 Inconel 700 250 HB 0.06 0.10 25 35 00.08 30

34 Stellite 21 350 HB 0.06 0.10 23 35 00.08 29

36 TiAl6V4 - 0.06 0.10 35 60 00.08 45

37 T40 - 0.06 0.10 28 40 00.08 34

38 45 HRc 0.06 0.10 50 90 00.08 70

38 50 HRc 0.06 0.10 40 70 00.08 55

38 55 HRc 0.06 0.10 30 60 00.08 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.10 0.12 200 400 00.11 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

350

DRILLING

350


WCMX 080412 NN – LT 30


1 125 HB 0.06 0.16 180 270 00.11 225

2 190 HB 0.06 0.16 180 230 00.11 205

3 250 HB 0.06 0.16 180 200 00.11 190

6 180 HB 0.06 0.16 120 230 00.11 175

4,6 230 HB 0.06 0.16 120 190 00.11 155

5,7 280 HB 0.06 0.15 100 170 00.11 135

8 350 HB 0.06 0.15 100 150 00.11 125

10 220 HB 0.09 0.16 70 170 00.13 120

10 280 HB 0.09 0.16 70 150 00.13 110

11 320 HB 0.09 0.14 60 130 00.11 95

11 350 HB 0.09 0.14 60 100 00.11 80

14 180 HB 0.06 0.15 170 230 00.11 200

14 240 HB 0.09 0.15 120 210 00.12 165

14 290 HB 0.09 0.14 70 120 00.11 95

14 310 HB 0.09 0.14 70 120 00.11 95

12 200 HB 0.09 0.14 100 150 00.11 125

13 42 HRc 0.06 0.13 60 100 00.09 80

15 150 HB 0.10 0.18 150 230 00.14 190

15 200 HB 0.10 0.18 150 210 00.14 180

16 250 HB 0.10 0.18 150 170 00.14 160

17,19 150 HB 0.10 0.18 120 200 00.14 160

17,19 200 HB 0.10 0.18 120 170 00.14 145

18,20 250 HB 0.10 0.18 120 150 00.14 135

31,32 Incoloy 800 240 HB 0.06 0.13 25 35 00.09 30

33 Inconel 700 250 HB 0.06 0.13 25 35 00.09 30

34 Stellite 21 350 HB 0.06 0.13 23 35 00.09 29

36 TiAl6V4 - 0.06 0.13 35 60 00.09 45

37 T40 - 0.06 0.13 28 40 00.09 34

38 45 HRc 0.06 0.13 50 90 00.09 70

38 50 HRc 0.06 0.13 40 70 00.09 55

38 55 HRc 0.06 0.13 30 60 00.09 45



NF Al (>8%Si) 12 25 AlSi12 130 HB 0.10 0.16 200 400 00.13 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8




Vc [m/min]





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

351

THREAD MILLING

THREAD MILLING

THREADMILLING

352

THREAD MILLING

TMC03012L5 0.35 ISO TH400001M1.6x0.35 0.35 39 5.1 3 1.20 3

TMC06015L6 0.4 ISO TH400019M2.0x0.4 0.40 39 6.1 3 1.54 3

TMC06019L7 0.45 ISO TH400016M2.5x0.45 0.45 39 7.6 4 1.96 3

TMC06024L9 0. 5 ISO TH400013M3.0x0.5 0.50 51 9.3 4 2.40 3

TMC06031L12 0.7 ISO TH400004M4.0x0.7 0.70 51 12.4 6 3.15 3

TMC06040L15 0.8 ISO TH400010M5.0x0.8 0.80 57 15.6 6 4.00 3

TMC06047L19 1.0 ISO TH400007M6.0x1.0 1.00 57 19.0 6 4.75 3

TMC06059L24 1.25 ISO TH400022M8.0x1.25 1.25 57 24.3 6 5.95 3

TMC08079L31 1.5 ISO TH400025M10x1.5 1.50 63 31.0 8 7.90 3

Thread Size Pitchmm Catalog Nr.L L1 D1 D2 N° of

FlutesDesignation

ISO METRIC Internal Miniature Tools

Thread Length - Up to 3D D = Nominal Thread Size

60°

1/8P

1/4PUNNUT

UNSCREW

ISO 965-1:1999-11DIN 13: 2005-08

L1L

D2 D1

TH4000520-80UNF- 80 39 3.9 3 1.18 3TMC03011L3 80UN

TH4000401-72UNF- 72 39 5.8 3 1.44 3TMC03014L5 72UN

TH4000343-56UNF2-56UNC 56 39 6.8 3 1.66 3TMC03016L6 56UN

TH400028-4-40UNC 40 51 8.1 6 2.12 3TMC06021L8 40UN

TH4000556-40UNF5-40UNC 40 51 9.8 6 2.46 3TMC06024L9 40UN

TH400031-6-32UNC 32 51 10.7 6 2.57 3TMC06025L10 32UN

TH40003710-32UNF8-32UNC 32 57 12.7 6 3.22 3TMC06032L12 32UN

TH4000431/4-28UNF- 28 57 19.3 6 5.20 3TMC06052L19 28 UN

TH4000495/16-24UNF- 24 63 24.2 8 6.65 3TMC08066L24 24 UN

Fine UNFCoarse UNC PitchTPI Catalog Nr.L L1 D1 D2 N° of

FlutesDesignation

UN Internal Miniature Tools

TH4000467/16-20UNF1/4-20UNC 20 19.4 6 4.85 3TMC06048L19 20UN 57

353

THREAD MILLING

min max

1 125 HB 80 130

2 190 HB 70 110

3 250 HB 60 100

6 180 HB 70 110

4,6 230 HB 70 110

5,7 280 HB 60 100

8 350 HB 50 80

10 220 HB 70 110

10 280 HB 60 100

11 320 HB 50 80

11 350 HB 50 70

14 180 HB 70 110

14 240 HB 60 90

14 290 HB 60 80

14 310 HB 60 80

12 200 HB 70 90

13 42 HRc 60 80

15 150 HB 60 110

15 200 HB 70 110

16 250 HB 60 90

17,19 150 HB 60 110

17,19 200 HB 60 90

18,20 250 HB 60 90

31,32 Incoloy 800 240 HB 40 60

33 Inconel 700 250 HB 30 50

34 Stellite 21 350 HB 20 40

36 TiAl6V4 - 40 70

37 T40 - 25 50

38 45 HRc 30 50

38 50 HRc 25 50

38 55 HRc 25 40

Chilled Cast Iron 40 Ni-Hard 2 400 HB 25 40

White Cast Iron 41 G-X300CrMo15 55 HRc 25 40

NF Al (>8%Si) 12 25 AlSi12 130 HB 80 300

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

4304, 316,

X5CrNi18-9

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

X100CrMo13, 440C,

G-X260NiCr4211

GGG40, GGG70, 50005

9

10

7 GG20, GG40, EN-GJL-250,

No30B

8



Vc [m/min]

min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

Feed (mm/tooth) per cutting dia

1.5-3.0 3.0-5.0 5.0-7.0 7.0-9.0 9.0-11

354

SOLID END MILL

355

SOLID END MILL

SOLID ENDMILLSSOLID CARBIDEEND MILLS LT 4000

SOLIDENDMILL

356

SOLID END MILL

2 fl

30°

L2

L1

D2 D1

L2

L1

D2 D1

Designation D1 Catalog Nr.L2D2 L1

E90 Z2 D01.0(03) L03.0(038) LT 4000 1.0 3 38 3.0 M5003520

E90 Z2 D01.5(03) L05.0(038) LT 4000 1.5 3 38 5.0 M5003537

E90 Z2 D02.0(03) L06.0(038) LT 4000 2.0 3 38 6.0 M5003538

E90 Z2 D02.5(03) L07.0(038) LT 4000 2.5 3 38 7.0 M5003539

E90 Z2 D03.0(03) L09.0(038) LT 4000 3.0 3 38 9.0 M5003540

E90 Z2 D04.0(04) L14.0(050) LT 4000 4.0 4 50 14.0 M5003541

E90 Z2 D05.0(05) L16.0(050) LT 4000 5.0 5 50 16.0 M5003542

E90 Z2 D06.0(06) L20.0(063) LT 4000 6.0 6 63 20.0 M5003543

E90 Z2 D08.0(08) L20.0(063) LT 4000 8.0 8 63 20.0 M5003544

E90 Z2 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003545

E90 Z2 D12.0(12) L26.0(075) LT 4000 12.0 12 75 26.0 M5003546

90° 2 Flutes

357

SOLID END MILLMachining Conditions

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.024 0.030 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.011 0.016 0.025 0.030 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.011 0.016 0.025 0.030 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.007 0.009 0.014 0.020 0.024 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.007 0.009 0.014 0.020 0.024 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.010 0.015 0.021 0.026 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.010 0.015 0.021 0.026 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.007 0.008 0.011 0.016 0.020 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.007 0.008 0.011 0.016 0.020 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.007 0.008 0.012 0.017 0.022 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.007 0.008 0.012 0.017 0.022 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.006 0.006 0.009 0.013 0.017 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.014 0.020 0.029 0.036 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.010 0.012 0.017 0.025 0.031 90 130

31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 30 50

33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 25 45

34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.006 0.007 0.010 0.014 0.018 20 50

36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.006 0.007 0.010 0.015 0.018 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.006 0.007 0.010 0.015 0.018 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.004 0.005 0.007 0.011 0.013 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.004 0.005 0.007 0.011 0.013 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.003 0.004 0.005 0.008 0.010 30 50

NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 0.1xØ 0.011 0.013 0.018 0.027 0.033 160 250

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316, X5CrNi18-

9

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

E90° Z2 Ø 1 - 5 – LT 4000


Material Examples Hardness

profiling slotting fz[mm/tooth] Vc [m/min]

ap ae ap Ø 1.0 Ø 2.0 Ø3.0 Ø4.0 Ø5.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

358

SOLID END MILL Machining Conditions

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130

31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 30 50

33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 25 45

34 Stellite 21 350 HB 1.5xØ 0.3xØ 1.0xØ 0.023 0.031 0.037 0.044 20 50

36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 0.1xØ 0.042 0.058 0.069 0.081 160 250

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316, X5CrNi18-

9

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

E90° Z2 Ø 6, 8, 10, 12 – LT 4000


Material Examples Hardness profiling slotting fz[mm/tooth] Vc [m/min]

ap ae ap Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

359

SOLID END MILL

3 fl

40°

L2

L1

D2 D1


E90 Z3 D03.0(06) L08.0(050) LT 4000 3.0 6 50 8.0 M5003548

E90 Z3 D04.0(06) L11.0(050) LT 4000 4.0 6 50 11.0 M5003549

E90 Z3 D05.0(06) L13.0(050) LT 4000 5.0 6 50 13.0 M5003550

E90 Z3 D06.0(06) L16.0(050) LT 4000 6.0 6 50 16.0 M5003551

E90 Z3 D08.0(08) L20.0(060) LT 4000 8.0 8 60 20.0 M5003552

E90 Z3 D10.0(10) L25.0(072) LT 4000 10.0 10 72 25.0 M5003553

E90 Z3 D12.0(12) L30.0(075) LT 4000 12.0 12 75 30.0 M5003554

90° 3 Flutes

v


360

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.015 0.021 0.026 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.015 0.021 0.026 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.016 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.016 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130

31,32 Incoloy 800 240 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 30 50

33 Inconel 700 250 HB 1.5xØ 0.3xØ 1.0xØ 0.010 0.014 0.018 25 45

34 Stellite 21 350 HB 1.5xØ 0.2xØ 1.0xØ 0.010 0.014 0.018 20 50

36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.007 0.011 0.013 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.007 0.011 0.013 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.006 0.009 0.012 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.006 0.009 0.012 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.006 0.008 0.010 30 50

NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5 x Ø 1.0 x Ø 0.018 0.027 0.033 160 250

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

2

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

8

X100CrMo13, 440C,

G-X260NiCr42 11

9

10

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

E90° Z3 Ø 3 - 5 – LT 4000




ap ae ap Ø 3.0 Ø 4.0 Ø5.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


361

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.054 0.065 0.076 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.054 0.065 0.076 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.034 0.046 0.055 0.065 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.034 0.046 0.055 0.065 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.028 0.033 0.039 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.020 0.028 0.033 0.039 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.017 0.023 0.028 0.032 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.017 0.023 0.028 0.032 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.015 0.020 0.024 0.028 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.015 0.020 0.024 0.028 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50



NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5 x Ø 1.0 x Ø 0.042 0.058 0.069 0.081 160 250

8

X100CrMo13, 440C,

G-X260NiCr42 11

9

10

GGG40, GGG70, 50005

7 GG20, GG40, EN-GJL-250,

No30B

5X2CrNiN23-4,

S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

2

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

E90° Z3 Ø 6, 8, 10, 12 – LT 4000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


Material Ex mples Hardness




362

SOLID END MILL

L2

L1

D2 D1

L2

L1

D2 D138°- 41°

4 fl

unequal

variable


90° 4 Flutes

E90 Z4 D03.0(06) L08.0(050) LT 4000 3.0 6 50 8.0 M5003572

E90 Z4 D04.0(06) L11.0(050) LT 4000 4.0 6 50 11.0 M5003573

E90 Z4 D05.0(06) L13.0(050) LT 4000 5.0 6 50 13.0 M5003574

E90 Z4 D06.0(06) L16.0(050) LT 4000 6.0 6 50 16.0 M5003575

E90 Z4 D08.0(08) L20.0(060) LT 4000 8.0 8 60 20.0 M5003576

E90 Z4 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003577

E90 Z4 D12.0(12) L26.0(075) LT 4000 12.0 12 75 26.0 M5003578

E90 Z4 D16.0(16) L38.0(100) LT 4000 16.0 16 100 38.0 M5003579

E90 Z4 D01.0(04) L04.0(050) LT 4000 1.0 4 50 4.0 M5003555

E90 Z4 D01.5(04) L05.0(050) LT 4000 1.5 4 50 5.0 M5003569

E90 Z4 D01.0(04) L05.0(050) LT 4000 1.5 4 50 5.0 M5003569

E90 Z4 D01.5(04) L07.5(050) LT 4000 1.5 4 50 7.5 M5003556

E90 Z4 D02.5(04) L12.5(050) LT 4000 2.5 4 50 12 .5 M5003558

E90 Z4 D02.0(04) L08.0(050) LT 4000 2.0 4 50 8.0 M5003557

E90 Z4 D02.0(04) L06.0(050) LT 4000 2.0 4 50 6.0 M5003570

E90 Z4 D02.5(04) L08.0(050) LT 4000 2.5 4 50 8.0 M5003571

363

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50



NF Al (>8%Si) 12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

E90° Z4 Ø 3 - 5 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


364

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50




X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

E90° Z4 Ø 6, 8, 10, 12 – LT 4000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)






365

SOLID END MILL

unequal

L2

L1

D2 D1

R38°- 41°

4 fl

variable

90° 4 Flutes with RadiusProduct Designation D1 D2 L1 L2 R Catalog Nr.

E90 Z4 D03.0(06) L08.0(050)R0.5 LT 4000 3.0 6 50 8.0 0.5 M5003614

E90 Z4 D04.0(06) L11.0(050)R0.5 LT 4000 4.0 6 50 11.0 0.5 M5003615

E90 Z4 D05.0(06) L13.0(050)R0.5 LT 4000 5.0 6 50 13.0 0.5 M5003616

E90 Z4 D06.0(06) L16.0(050)R0.5 LT 4000 6.0 6 50 16.0 0.5 M5003617

E90 Z4 D08.0(08) L20.0(060)R0.5 LT 4000 8.0 8 60 20.0 0.5 M5003618

E90 Z4 D10.0(10) L22.0(072)R0.5 LT 4000 10.0 10 72 22.0 0.5 M5003619

E90 Z4 D12.0(12) L26.0(075)R0.5 LT 4000 12.0 12 75 26.0 0.5 M5003620

E90 Z4 D03.0(06) L08.0(050)R1.0 LT 4000 3.0 6 50 08.0 1.0 M5003623

E90 Z4 D04.0(06) L11.0(050)R1.0 LT 4000 4.0 6 50 11.0 1.0 M5003624

E90 Z4 D05.0(06) L13.0(050)R1.0 LT 4000 5.0 6 50 13.0 1.0 M5003625

E90 Z4 D06.0(06) L16.0(050)R1.0 LT 4000 6.0 6 50 16.0 1.0 M5003626

E90 Z4 D08.0(08) L20.0(060)R1.0 LT 4000 8.0 8 60 20.0 1.0 M5003627

E90 Z4 D10.0(10) L22.0(072)R1.0 LT 4000 10.0 10 72 22.0 1.0 M5003628

E90 Z4 D12.0(12) L26.0(075)R1.0 LT 4000 12.0 12 75 26.0 1.0 M5003629

E90 Z4 D06.0(06) L16.0(050)R2.0 LT 4000 6.0 6 50 16.0 2.0 M5003632

E90 Z4 D08.0(08) L20.0(060)R2.0 LT 4000 8.0 8 60 20.0 2.0 M5003633

E90 Z4 D10.0(10) L22.0(072)R2.0 LT 4000 10.0 10 72 22.0 2.0 M5003634

E90 Z4 D12.0(12) L26.0(075)R2.0 LT 4000 12.0 12 75 26.0 2.0 M5003635

Product Designation D1 D2 L1 L2 R Catalog Nr.

E90 Z4 D08.0(08) L32.0(090)R0.5 LT 4000 8.0 8 90 32.0 0.5 M5003638

E90 Z4 D10.0(10) L40.0(100)R0.5 LT 4000 10.0 10 100 40.0 0.5 M5003639

E90 Z4 D12.0(12) L48.0(110)R0.5 LT 4000 12.0 12 110 48.0 0.5 M5003640

90° 4 Flutes with Radius, Long

366


1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50

40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 35 55

41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50

12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

2

X2CrNiN23-4, S31500

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

E90° Z4 with Radius 0.5, Ø 3 - 5 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

367


1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55

41 G-X300CrMo15 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

2

X2CrNiN23-4, S31500

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

E90° Z4 with Radius 0.5, Ø 6, 8, 10, 12 – LT 4000

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)





368


1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.024 0.030 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.016 0.025 0.030 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.014 0.020 0.024 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.015 0.021 0.026 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.011 0.016 0.020 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.012 0.017 0.022 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.009 0.013 0.017 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.020 0.029 0.036 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.025 0.031 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.010 0.015 0.018 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.007 0.011 0.013 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 30 50

40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.005 0.008 0.010 35 55


12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.018 0.027 0.033 160 250

2

X2CrNiN23-4, S31500

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

E90° Z4 with Radius 1.0, Ø 3 - 5 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

369


1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55


12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250

2

X2CrNiN23-4, S31500

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)





370


1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.039 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.032 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.033 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.025 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.028 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.021 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.047 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.040 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.023 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.017 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 30 50

40 Ni-Hard 2 400 HB 1.5xØ 0.2xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55


12 25 AlSi12 130 HB 1.5xØ 0.5xØ 1.0xØ 0.042 0.058 0.069 0.081 160 250

2

X2CrNiN23-4, S31500

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42



Material Examples Hardness profiling slotting fz[mm/tooth] Vc [m/min]


Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

371


1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 150 200

2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 140 190

3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 120 160

6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.044 0.053 0.062 120 180

4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.044 0.053 0.062 90 130

5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 80 120

8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 60 90

10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 70 130

10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.035 0.042 0.049 65 110

11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.025 0.030 0.035 60 90

11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.025 0.030 0.035 50 80

14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.039 0.045 80 120

14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.039 0.045 70 115

14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.025 0.030 0.035 60 100

14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.025 0.030 0.035 60 90

12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.029 0.033 50 90

13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.024 0.029 0.033 30 55

15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 140 200

15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 150 190

16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.047 0.056 0.066 120 160

17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 130 180

17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 110 150

18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.045 0.053 0.063 90 130




36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.020 0.024 0.028 30 60

37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.020 0.024 0.028 40 70

38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.017 0.021 0.024 40 60

38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.017 0.021 0.024 35 55

38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.015 0.018 0.021 30 50

40 Ni-Hard 2 400 HB 3.0xØ 0.10xØ 0.1xØ 0.015 0.018 0.021 35 55


12 25 AlSi12 130 HB 3.0xØ 0.25xØ 1.0xØ 0.050 0.059 0.070 160 250

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

10

8

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3

X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

E90° Z4 with Radius 0.5 Long, Ø 8, 10, 12 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)

372

SOLID END MILL

L2

L1

D2 D1

4 fl

unequal

38°-41°

variable

E90 Z4 D03.0(06) L12.0(050) LT 4000 3.0 6 50 12.0 M5003559 E90 Z4 D04.0(06) L16.0(055) LT 4000 4.0 6 55 16.0 M5003560

E90 Z4 D05.0(06) L20.0(060) LT 4000 5.0 6 60 20.0 M5003561 E90 Z4 D06.0(06) L24.0(065) LT 4000 6.0 6 65 24.0 M5003562

E90 Z4 D08.0(08) L32.0(090) LT 4000 8.0 8 90 32.0 M5003563 E90 Z4 D10.0(10) L40.0(100) LT 4000 10.0 10 100 40.0 M5003564

E90 Z4 D12.0(12) L48.0(110) LT 4000 12.0 12 110 48.0 M5003565

E90 Z4 D16.0(16) L64.0(160) LT 4000 16.0 16 160 64.0 M5003566

Product Designation D1 Catalog Nr.L2D2 L1

90° 4 Flutes, Long

373

SOLID END MILL

1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 150 200

2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 140 190

3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 120 160

6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.008 0.010 0.014 0.020 0.025 120 180

4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.008 0.010 0.014 0.020 0.025 90 130

5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 80 120

8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 60 90

10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 70 130

10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.007 0.008 0.011 0.016 0.020 65 110

11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.005 0.006 0.008 0.011 0.014 60 90

11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.005 0.006 0.008 0.011 0.014 50 80

14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.006 0.007 0.010 0.015 0.019 80 120

14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.007 0.010 0.015 0.019 70 115

14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.006 0.008 0.011 0.014 60 100

14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.006 0.008 0.011 0.014 60 90

12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.005 0.005 0.008 0.011 0.014 50 90

13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.005 0.005 0.008 0.011 0.014 30 55

15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 140 200

15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 150 190

16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.011 0.015 0.022 0.027 120 160

17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 130 180

17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 110 150

18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.009 0.010 0.014 0.021 0.026 90 130

31,32 Incoloy 800 240 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 30 50

33 Inconel 700 250 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 25 45

34 Stellite 21 350 HB 3.0xØ 0.10xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 20 50

36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 30 60

37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.004 0.004 0.006 0.009 0.011 40 70

38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.004 0.006 0.008 0.010 40 60

38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.004 0.006 0.008 0.010 35 55

38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.003 0.003 0.005 0.007 0.009 30 50

NF AAl (>8%Si) 12 25 AlSi12 130 HB 3.0xØ 0.25xØ 1.0xØ 0.010 0.011 0.016 0.023 0.029 160 250

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Steel

11

GGG40, GGG70, 50005

HTA

Fe, Ni & Co based

9

Ti based

Cast

Iron


No30B

Malleable & Nodular

10

8

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6Stee

l

Non-alloyed

Low alloyed

High alloyed 3

Stai

nles

s St

eel

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500



X5CrNi18-9

Duplex

E90° Z4 Long Ø 1 - 5 – LT 4000




ap ae ap Ø 1.0 Ø 2.0 Ø3.0 Ø4.0 Ø5.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


374

SOLID END MILL

1 125 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 150 200

2 190 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 140 190

3 250 HB 3.0xØ 0.25xØ 1.0xØ 0.036 0.050 0.059 0.070 120 160

6 180 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.044 0.053 0.062 120 180

4,6 230 HB 3.0xØ 0.25xØ 1.0xØ 0.032 0.044 0.053 0.062 90 130

5,7 280 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 80 120

8 350 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 60 90

10 220 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 70 130

10 280 HB 3.0xØ 0.25xØ 0.7xØ 0.026 0.035 0.042 0.049 65 110

11 320 HB 3.0xØ 0.25xØ 0.5xØ 0.018 0.025 0.030 0.035 60 90

11 350 HB 3.0xØ 0.25xØ 0.5xØ 0.018 0.025 0.030 0.035 50 80

14 180 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.032 0.039 0.045 80 120

14 240 HB 3.0xØ 0.25xØ 1.0xØ 0.024 0.032 0.039 0.045 70 115

14 290 HB 3.0xØ 0.25xØ 1.0xØ 0.018 0.025 0.030 0.035 60 100

14 310 HB 3.0xØ 0.25xØ 1.0xØ 0.018 0.025 0.030 0.035 60 90

12 200 HB 3.0xØ 0.25xØ 1.0xØ 0.017 0.024 0.029 0.033 50 90

13 42 HRc 3.0xØ 0.25xØ 1.0xØ 0.017 0.024 0.029 0.033 30 55

15 150 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 140 200

15 200 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 150 190

16 250 HB 3.0xØ 0.25xØ 1.0xØ 0.035 0.047 0.056 0.066 120 160

17,19 150 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 130 180

17,19 200 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 110 150

18,20 250 HB 3.0xØ 0.25xØ 1.0xØ 0.033 0.045 0.053 0.063 90 130




36 TiAl6V4 - 3.0xØ 0.25xØ 1.0xØ 0.015 0.020 0.024 0.028 30 60

37 T40 - 3.0xØ 0.25xØ 1.0xØ 0.015 0.020 0.024 0.028 40 70

38 45 HRc 3.0xØ 0.10xØ 0.1xØ 0.013 0.017 0.021 0.024 40 60

38 50 HRc 3.0xØ 0.10xØ 0.1xØ 0.013 0.017 0.021 0.024 35 55

38 55 HRc 3.0xØ 0.10xØ 0.1xØ 0.011 0.015 0.018 0.021 30 50




X100CrMo13, 440C,

G-X260NiCr42 11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

3X40CrMoV5,

H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

E90° Z4 Long Ø 6, 8, 10, 12 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


375

SOLID END MILL

45°

4 fl

L2

L1

D2 D1

L2

L1

D2 D1

ERO Z3 D04.0(06) L11.0(057) LT 4000 4.0 6 57 11.0 M5003607

ERO Z4 D05.0(06) L13.0(057) LT 4000 5.0 6 57 13.0 M5003608

ERO Z4 D06.0(06) L13.0(057) LT 4000 6.0 6 57 13.0 M5003609 ERO Z4 D08.0(08) L19.0(063) LT 4000 8.0 8 63 19.0 M5003610

ERO Z4 D10.0(10) L22.0(072) LT 4000 10.0 10 72 22.0 M5003611 ERO Z4 D12.0(12) L26.0(083) LT 4000 12.0 12 83 26.0 M5003612

Product Designation

Product Designation

D1

D1

Catalog Nr.

Catalog Nr.

L2

L2

D2

D2

L1

L1

90° 3 Flutes, Rougher

90° 4 Flutes, Rougher

376

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.024 0.030 0.040 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.030 0.039 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.030 0.039 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.020 0.024 0.032 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.020 0.024 0.032 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.026 0.033 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.021 0.026 0.033 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.016 0.020 0.025 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.016 0.020 0.025 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.022 0.028 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.017 0.022 0.028 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.013 0.017 0.021 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.036 0.047 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.025 0.031 0.040 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.015 0.018 0.023 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.015 0.018 0.023 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.011 0.013 0.017 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.011 0.013 0.017 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.008 0.010 0.013 30 50




11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

ERO Z4 Ø 4, 5, 6 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


377

SOLID END MILL

1 125 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 150 200

2 190 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 140 190

3 250 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.065 0.077 120 160

6 180 HB 1.5xØ 0.5xØ 1.0xØ 0.053 0.063 0.074 120 180

4,6 230 HB 1.5xØ 0.5xØ 1.0xØ 0.053 0.063 0.074 90 130

5,7 280 HB 1.5xØ 0.5xØ 0.7xØ 0.043 0.052 0.062 80 120

8 350 HB 1.5xØ 0.5xØ 0.7xØ 0.043 0.052 0.062 60 90

10 220 HB 1.5xØ 0.5xØ 1.0xØ 0.046 0.055 0.064 70 130

10 280 HB 1.5xØ 0.5xØ 1.0xØ 0.046 0.055 0.064 65 110

11 320 HB 1.5xØ 0.5xØ 0.6xØ 0.035 0.041 0.049 60 90

11 350 HB 1.5xØ 0.5xØ 0.6xØ 0.035 0.041 0.049 50 80

14 180 HB 1.5xØ 0.5xØ 1.0xØ 0.038 0.045 0.053 80 120

14 240 HB 1.5xØ 0.5xØ 1.0xØ 0.038 0.045 0.053 70 115

14 290 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 60 100

14 310 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 60 90

12 200 HB 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 50 90

13 42 HRc 1.5xØ 0.5xØ 1.0xØ 0.029 0.035 0.040 30 55

15 150 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 140 200

15 200 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 150 190

16 250 HB 1.5xØ 0.5xØ 1.0xØ 0.064 0.076 0.089 120 160

17,19 150 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 130 180

17,19 200 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 110 150

18,20 250 HB 1.5xØ 0.5xØ 1.0xØ 0.055 0.066 0.077 90 130




36 TiAl6V4 - 1.5xØ 0.5xØ 1.0xØ 0.032 0.038 0.045 30 60

37 T40 - 1.5xØ 0.5xØ 1.0xØ 0.032 0.038 0.045 40 70

38 45 HRc 1.5xØ 0.3xØ 0.2xØ 0.023 0.028 0.032 40 60

38 50 HRc 1.5xØ 0.3xØ 0.2xØ 0.023 0.028 0.032 35 55

38 55 HRc 1.5xØ 0.2xØ 0.1xØ 0.017 0.021 0.024 30 50




11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

1C35, Ck45, 1020, 1045, 1060, 28Mn6

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

2

X2CrNiN23-4, S31500

3

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

ERO Z4 Ø 8, 10, 12 – LT 4000





Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


378

SOLID END MILL

L2

L1

D2 D1

R

L2

L1

D2 D1

R

2 fl

30°

EBN Z2 D01.0(03) L03.0(038) R0.50 LT 4000 1.0 3 38 3.0 0.50 M5003587

EBN Z2 D01.5(03) L05.0(038) R0.75 LT 4000 1.5 3 38 5.0 0.75 M5003588 EBN Z2 D02.0(03) L06.0(038) R1.00 LT 4000 2.0 3 38 6.0 1.0 0 M5003589

EBN Z2 D02.5(03) L07.0(038) R1.25 LT 4000 2.5 3 38 7.0 1.25 M5003590 EBN Z2 D03.0(03) L09.0(038) R1.50 LT 4000 3.0 3 38 9.0 1.50 M5003591




Product Designation D1 Catalog Nr.L2 RD2 L1

Ball Nose, 2 Flutes

379

SOLID END MILL

1 125 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 150 200

2 190 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 140 190

3 250 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 120 160

6 180 HB 0.25xØ 0.7xØ 0.033 0.042 0.061 0.075 0.099 120 180

4,6 230 HB 0.25xØ 0.7xØ 0.033 0.042 0.061 0.075 0.099 90 130

5,7 280 HB 0.25xØ 0.7xØ 0.028 0.036 0.052 0.064 0.084 80 120

8 350 HB 0.25xØ 0.7xØ 0.028 0.036 0.052 0.064 0.084 60 90

10 220 HB 0.25xØ 0.7xØ 0.028 0.036 0.051 0.063 0.083 70 130

10 280 HB 0.25xØ 0.7xØ 0.028 0.036 0.051 0.063 0.083 65 110

11 320 HB 0.25xØ 0.7xØ 0.021 0.027 0.039 0.048 0.063 60 90

11 350 HB 0.25xØ 0.7xØ 0.021 0.027 0.039 0.048 0.063 50 80

14 180 HB 0.25xØ 0.7xØ 0.023 0.029 0.042 0.052 0.068 80 120

14 240 HB 0.25xØ 0.7xØ 0.023 0.029 0.042 0.052 0.068 70 115

14 290 HB 0.25xØ 0.7xØ 0.018 0.023 0.033 0.040 0.053 60 100

14 310 HB 0.25xØ 0.7xØ 0.018 0.023 0.033 0.040 0.053 60 90

12 200 HB 0.25xØ 0.7xØ 0.024 0.031 0.044 0.054 0.071 50 90

13 42 HRc 0.25xØ 0.7xØ 0.024 0.031 0.044 0.054 0.071 30 55

15 150 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 140 200

15 200 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 150 190

16 250 HB 0.25xØ 0.7xØ 0.039 0.050 0.072 0.088 0.116 120 160

17,19 150 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 130 180

17,19 200 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 110 150

18,20 250 HB 0.25xØ 0.7xØ 0.033 0.043 0.062 0.076 0.100 90 130

31,32 Incoloy 800 240 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 30 50

33 Inconel 700 250 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 25 45

34 Stellite 21 350 HB 0.25xØ 0.6xØ 0.022 0.029 0.042 0.051 0.067 20 50

36 TiAl6V4 - 0.25xØ 0.7xØ 0.019 0.025 0.036 0.044 0.058 30 60

37 T40 - 0.25xØ 0.7xØ 0.019 0.025 0.036 0.044 0.058 40 70

38 45 HRc 0.25xØ 0.6xØ 0.014 0.018 0.026 0.032 0.042 40 60

38 50 HRc 0.25xØ 0.6xØ 0.014 0.018 0.026 0.032 0.042 35 55

38 55 HRc 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 0.25xØ 0.3xØ 0.011 0.014 0.020 0.024 0.032 30 50

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.25xØ 0.7xØ 0.035 0.045 0.065 0.080 0.105 160 250

3

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

EBN Z2 Ø 1 - 5 – LT 4000



contouring fz[mm/tooth] Vc [m/min]

ap ae Ø1.0 Ø2.0 Ø 3.0 Ø 4.0 Ø 5.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


380

SOLID END MILL

1 125 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 150 200

2 190 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 140 190

3 250 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 120 160

6 180 HB 0.25xØ 0.7xØ 0.094 0.108 0.118 0.132 120 180

4,6 230 HB 0.25xØ 0.7xØ 0.094 0.108 0.118 0.132 90 130

5,7 280 HB 0.25xØ 0.7xØ 0.080 0.092 0.100 0.112 80 120

8 350 HB 0.25xØ 0.7xØ 0.080 0.092 0.100 0.112 60 90

10 220 HB 0.25xØ 0.7xØ 0.079 0.091 0.099 0.111 70 130

10 280 HB 0.25xØ 0.7xØ 0.079 0.091 0.099 0.111 65 110

11 320 HB 0.25xØ 0.7xØ 0.060 0.069 0.075 0.084 60 90

11 350 HB 0.25xØ 0.7xØ 0.060 0.069 0.075 0.084 50 80

14 180 HB 0.25xØ 0.7xØ 0.065 0.075 0.081 0.091 80 120

14 240 HB 0.25xØ 0.7xØ 0.065 0.075 0.081 0.091 70 115

14 290 HB 0.25xØ 0.7xØ 0.050 0.058 0.063 0.070 60 100

14 310 HB 0.25xØ 0.7xØ 0.050 0.058 0.063 0.070 60 90

12 200 HB 0.25xØ 0.7xØ 0.068 0.078 0.085 0.095 50 90

13 42 HRc 0.25xØ 0.7xØ 0.068 0.078 0.085 0.095 30 55

15 150 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 140 200

15 200 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 150 190

16 250 HB 0.25xØ 0.7xØ 0.110 0.127 0.138 0.154 120 160

17,19 150 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 130 180

17,19 200 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 110 150

18,20 250 HB 0.25xØ 0.7xØ 0.095 0.109 0.119 0.133 90 130

31,32 Incoloy 800 240 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 30 50

33 Inconel 700 250 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 25 45

34 Stellite 21 350 HB 0.25xØ 0.6xØ 0.064 0.074 0.080 0.090 20 50

36 TiAl6V4 - 0.25xØ 0.7xØ 0.055 0.063 0.069 0.077 30 60

37 T40 - 0.25xØ 0.7xØ 0.055 0.063 0.069 0.077 40 70

38 45 HRc 0.25xØ 0.6xØ 0.040 0.046 0.050 0.056 40 60

38 50 HRc 0.25xØ 0.6xØ 0.040 0.046 0.050 0.056 35 55

38 55 HRc 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 0.25xØ 0.3xØ 0.030 0.035 0.038 0.042 30 50

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.25xØ 0.7xØ 0.100 0.115 0.125 0.140 160 250

3

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

5

1C35, Ck45, 1020, 1045, 1060, 28Mn6

2

X2CrNiN23-4, S31500

6 410, X6Cr17, 17-4 PH, 430

4304, 316,

X5CrNi18-9

11

GGG40, GGG70, 50005

9

7 GG20, GG40, EN-GJL-250,

No30B

10

8

X100CrMo13, 440C,

G-X260NiCr42

EBN Z2 Ø 6, 8, 10, 12 – LT 4000




ap ae Ø 6.0 Ø 8.0 Ø 10.0 Ø 12.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Stai

nles

s St

eel Austenitic

Duplex


Cast

Iron

Grey

Malleable & Nodular

High

Tem

p. A

lloys

Fe, Ni & Co Based

Ti Based

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron

NF Al (>8%Si)


381

SOLID END MILL

L2

L1

D2 D1

R

0°

4 fl

EHF Z4 D03.0(06) L02.0(070) R0.37 LT 4000 3.0 6 70 2.0 M5003600

EHF Z4 D04.0(06) L02.0(070) R0.47 LT 4000 4.0 6 70 2.0 M5003601 EHF Z4 D05.0(06) L02.5(070) R0.60 LT 4000 5.0 6 70 2.5 M5003602

EHF Z4 D06.0(06) L03.0(070) R0.73 LT 4000 6.0 6 70 3.0 M5003603 EHF Z4 D08.0(08) L04.0(080) R0.98 LT 4000 8.0 8 80 4.0 M5003604

EHF Z4 D10.0(10) L05.0(090) R1.23 LT 4000 10.0 10 90 5.0 M5003605

EHF Z4 D12.0(12) L06.0(100) R1.65 LT 4000 12.0 12 100 6.0 M5003606

Product Designation D1 Catalog Nr.L2D2 L1

High Feed, 4 Flutes

382

SOLID END MILL

1 125 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 150 200

2 190 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 140 190

3 250 HB 0.025xØ 0.5xØ 0.140 0.200 0.240 120 160

6 180 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 120 180

4,6 230 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 90 130

5,7 280 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 80 120

8 350 HB 0.025xØ 0.5xØ 0.132 0.188 0.226 60 90

10 220 HB 0.025xØ 0.5xØ 0.111 0.158 0.190 70 130

10 280 HB 0.025xØ 0.5xØ 0.111 0.158 0.190 65 110

11 320 HB 0.025xØ 0.5xØ 0.084 0.120 0.144 60 90

11 350 HB 0.025xØ 0.5xØ 0.084 0.120 0.144 50 80

15 150 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 140 200

15 200 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 150 190

16 250 HB 0.025xØ 0.5xØ 0.154 0.220 0.264 120 160

17,19 150 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 130 180

17,19 200 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 110 150

18,20 250 HB 0.025xØ 0.5xØ 0.133 0.190 0.228 90 130

38 45 HRc 0.025xØ 0.5xØ 0.070 0.100 0.120 40 60

38 50 HRc 0.025xØ 0.5xØ 0.070 0.100 0.120 35 55

38 55 HRc 0.025xØ 0.3xØ 0.056 0.080 0.096 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.025xØ 0.3xØ 0.056 0.080 0.096 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 0.025xØ 0.3xØ 0.056 0.080 0.096 30 50

X100CrMo13, 440C,

G-X260NiCr42

Hard

ened

Steel

11

GGG40, GGG70, 50005

Cast

Iron


No30B


1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

High alloyed 3

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

2

EHF Z4 Ø 3 - 5 – LT 4000

1 125 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 150 200

2 190 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 140 190

3 250 HB 0.025xØ 0.5xØ 0.260 0.340 0.400 0.450 120 160

6 180 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 120 180

4,6 230 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 90 130

5,7 280 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 80 120

8 350 HB 0.025xØ 0.5xØ 0.244 0.320 0.376 0.423 60 90

10 220 HB 0.025xØ 0.5xØ 0.205 0.269 0.316 0.356 70 130

10 280 HB 0.025xØ 0.5xØ 0.205 0.269 0.316 0.356 65 110

11 320 HB 0.025xØ 0.5xØ 0.156 0.204 0.240 0.270 60 90

11 350 HB 0.025xØ 0.5xØ 0.156 0.204 0.240 0.270 50 80

15 150 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 140 200

15 200 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 150 190

16 250 HB 0.025xØ 0.5xØ 0.286 0.374 0.440 0.495 120 160

17,19 150 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 130 180

17,19 200 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 110 150

18,20 250 HB 0.025xØ 0.5xØ 0.247 0.323 0.380 0.428 90 130

38 45 HRc 0.025xØ 0.5xØ 0.130 0.170 0.200 0.225 40 60

38 50 HRc 0.025xØ 0.5xØ 0.130 0.170 0.200 0.225 35 55

38 55 HRc 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 30 50

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 35 55

White Cast Iron 41 G-X300CrMo15 55 HRc 0.025xØ 0.3xØ 0.104 0.136 0.160 0.180 30 50

X100CrMo13, 440C,

G-X260NiCr42

Har

dene

d Steel

11

GGG40, GGG70, 50005

Cas

t Iro

n


No30B


1C35, Ck45, 1020, 1045, 1060, 28Mn6

St

eel

Non-alloyed

Low alloyed

High alloyed 3

42CrMo4, St50, Ck60, 4140, 4340,

100Cr6

X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

2

EHF Z4 Ø 6, 8,10,12 – LT 4000




ap ae Ø 3.0 Ø 4.0 Ø 5.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron




ap ae Ø 6.0 Ø 8.0 Ø10.0 Ø12.0 min max

Non Alloyed

Stee

l Low Alloyed

High Alloyed

Cast

Iron

Grey

Malleable & Nodular

Hard

ened

Mat

.

Steel

Chilled Cast Iron

White Cast Iron


383

MATERIALS REFERENCE LIST

Material Reference List

384


385


386


387


388


lamina catalog 2016 en 06feb2017 - dallagottcdallagottc.com/.../2017/02/catalogo-lamina-2016.pdf ·...

Documents