kistler anayzer

Upload: sidaks6869

Post on 03-Jun-2018

215 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/12/2019 kistler anayzer

    1/4

    Der Miniatur-Ladungsverstrker Typ 5039A hatdie Aufgabe, das Ladungssignal piezoelektri-scher Sensoren in ein proportionales Span-nungssignal umzusetzen.Das Gert ist in einem robusten Metallgehusegemss Schutzart IP-65 untergebracht und frindustriellen Einsatz konzipiert.Der Typ 5039A ist ein einkanaliger Ladungs-verstrker mit zwei ferngesteuert-umschaltba-ren Messbereichen. Ausser einem Ausgang frdie Abnahme des Momentanwertes ist einzweiter Ausgang fr den gespeicherten Spit-zenwert vorhanden.

    Lamplificateur de charge miniaturis type5039A convertit les signaux de charges lec-triques provenant de capteurs pizolectriquesen des tensions proportionnelles.Linstrument est incorpor dans un botier m-tallique robuste conforme la classe de pro-tection IP-65 et conu pour lusage industriel.Le type 5039A est un amplificateur de charge un canal avec deux gammes de mesurecommutables par tlcommande. Outre unesortie pour la valeur momentane, unedeuxime sortie est disponible pour la valeurde crte mmorise.

    The miniature charge amplifier Type 5039Aconverts the electrical charge signals yieldedby piezoelectric sensors into proportional volt-ages.The instrument is integrated into a ruggedmetal housing according to degree of protec-tion IP-65 and conceived for industrial use.The Type 5039A is a one-channel chargeamplifier with two through remote controlswitchable measuring ranges. Besides the out-put for the instant value, another output for thestored peak value is available.

    Technische Daten Donnes techniques Technical Data

    Miniatur-LadungsverstrkerAmplificateur de charge miniaturisMiniature Charge Amplifier

    1 ... 4

    5039A...

    Ladungsverstrker Amplificateur de charge Charge amplifier Messbereich Range I Gamme de mesure Range I Measuring range Range I pC min. 5'000

    pC max. 50'000abgeglichen auf 5039A1xx rgle sur 5039A1xx adjusted to 5039A1xx pC 50'000

    5039A2xx 5039A2xx 5039A2xx pC 20'0005039A3xx 5039A3xx 5039A3xx pC gemss Bestellung / selon

    commande / according to order

    Messbereich Range II Gamme de mesure Range II Measuring range Range IIVerhltnis 5039Ax1x Rapport 5039Ax1x Ratio 5039Ax1x 10Range I / Range II 5039Ax2x Range I / Range II 5039Ax2x Range I / Range II 5039Ax2x 4

    5039Ax3x 5039Ax3x 5039Ax3x 2Drift Drive Drift pC/s 50zwischen Sensor-Low und entre Sensor-Low et between Sensor-Low andAusgangs-/Speise-GND GND Sortie/Alimentation Output/Supply GND(0 ... 500 Hz) (0 ... 500 Hz) (0 ... 500 Hz)

    Grsstes Eingangssignal Signal d'entre max. Largest input signalohne Beschdigung sans causer de dommage causing no damage

    Spannung Tension Voltage V 10Ladung Charge Charge pC 150'000

    Ferngesteuert-umschaltbare MessbereicheGammes de mesure commutables par tlcommande

    Measuring ranges switchable through remote control Spitzenspeicher-Schaltung mit separatem Ausgang

    Mmoire de crtes avec sortie sparePeak memory circuit with separate output

    Unterdrckung von Strspannungenzwischen Eingangs- und Ausgangsmasse bis 4 VSuppression d'interfrences entre la masse lectroniqued'entre et de sortie jusqu' 4 VSuppression of interferences betweeninput and output ground up to 4 V

    -konformConforme au Conforming to

    * In all Kistler documents, the decimal sign is a comma on the line (ISO 31-0:1992).

    1 g = 9,80665 m s 2; 1 m s 2 = 0,1019... g ; 1 inch = 25,4 mm; 1 Nm = 0,73756... lbft; 1 g = 0,03527... oz

    Kistler Instrumente AG, CH-8408 Winterthur, Switzerland, Tel. (052) 224 11 11 Kistler Instrument Corp., Amherst, NY 14228-2171, USA, Phone (716) 691-5100

    Measure & Analyze MCA

    0 0 0 - 3

    0 3 m - 1

    1 . 0

    1

    ( D B 1 1

    . 5 0 3 9 m

    )

  • 8/12/2019 kistler anayzer

    2/4

    2

    Instant-Ausgang (Output) Sortie Instant (Output) Instant Output Fehler Erreur Error % 1Nullpunktfehler (Reset) Erreur du zro (Reset) Zero point error (Reset) mV 11Ausgangsstrom Courant de sortie Output current mA max. 5Ausgangswiderstand Impdance de sortie Output impedance 10Frequenzbereich Gamme de frquence Frequency limit

    Abfall 5 % Chute 5 % Drop 5 % kHz 0 ... >6Abfall 3 dB Chute 3 dB Drop 3 dB kHz 0 ... 17

    Strsignal Signal d'interfrence Interference signalbei kleiner Eingangskapazitt pour petite capacit d'entre for small input capacitance(0,1 Hz ... 1 MHz) (0,1 Hz ... 1 MHz) (0,1 Hz ... 1 MHz) mVpp

  • 8/12/2019 kistler anayzer

    3/4

    BeschreibungDer Miniatur-Ladungsverstrker Typ 5039Aenthlt im Eingang einen kapazitativ gegen-gekoppelten Verstrker in Hybridbauweise mitextrem hoher Eingangsimpedanz.Durch eine Differenz-Eingangsschaltung blei-ben Gleichtaktsignale bis 4 V zwischen Sen-sor-Low und Ausgangs- bzw. Speisungs-Ground ohne strenden Einfluss; diese beidenPunkte der Schaltung sind nur ber R/C-Ele-mente miteinander verbunden. Eine weitereR/C-Kombination befindet sich zwischen Aus-gangs- bzw. Speisungs- Ground und derGehusemasse. Dadurch werden Strungendurch ein floatendes Gehuse vermieden.Momentanes Ausgangssignal ( Output) und ge-speicherter Spitzenwert (Output Peak) knnenan getrennten Anschlssen gleichzeitig abge-nommen werden. Das Zurcksetzen des Spit-zenwertes geschieht gleichzeitig mit demReset des Ladungsverstrker-Einganges.Die Ansteuerung der Eingnge Operate undRangeII erfolgt galvanisch getrennt berOptokoppler.Zur Speisung des Types 5039A gengt eineunstabilisierte Gleichspannung von 18 ... 36 V.Strombedarf ca. 30 mA.

    AnwendungDer Miniatur-Ladungsverstrker Typ 5039Akann dank seiner robusten und stossfestenBauweise im industriellen Bereich mit allenArten piezoelektrischer Messwertsensoren ver-wendet werden.Seine Ausgangssignale knnen z.B. an indu-strielle Steuerungen weitergeleitet und verar-beitet werden.Das dichte Gehuse, der stossfeste Aufbau

    und die einfache Stromversorgung ermgli-chen den Einsatz an Produktionsmaschinen, inFahrzeugen und in vielen anderen Bereichen.

    DescriptionDans ltage dentre, lamplificateur de chargeminiaturis type 5039A possde un amplifica-teur hybride contre-raction avec une imp-dance dentre extrmement leve.Grce un circuit dentre diffrentiateur, dessignaux en mode commun jusqu 4 V entreSensor Low et Ground Sortie resp. Alimentationrestent sans effet; ces deux points du circuit nesont connects que par des lments R/C.Une autre combinaison R/C se trouve entreGround Sortie/Alimentation et la masse dubotier. Ceci vite toutes interfrences dues un botier flottant.

    Le signal de sortie momentan ( Output) et lavaleur de crte mmorise (Output Peak) sontsimultanment disponibles des connecteursspares. La remise zro de la valeur decrte seffectue simultanment avec le Reset de lentre de lamplificateur de charge.Les entres Operate et RangeII sont asserviespar coupleurs opto-lectroniques (isolation lec-trique).Une tension c.c. non-stabilise de 18 ... 36 Vsuffit pour alimenter le type 5039A. Le courantncessaire est denv. 30 mA.

    ApplicationLamplificateur de charge miniaturis type5039A peut tre utilis grce sa construc-tion robuste et rsistante aux chocs dans lin-dustrie avec toutes sortes de capteurs pizo-lectriques.Les signaux de sortie peuvent p.ex. tre bran-chs sur des commandes industrielles et trai-ts ultrieurement.Le botier tanche, la construction rsistante

    aux chocs et lalimentation simple permettentdutiliser cet amplificateur sur des machines deproduction automobile et dans bien dautresdomaines.

    DescriptionThe miniature charge amplifier has a hybridnegative feedback amplifier with extremelyhigh input impedance in its input stage.

    Thanks to a differential input circuit common-

    mode signals up to 4 V between Sensor Low and Output resp. Supply Ground remain effect-less; both of these circuit points are only con-nected through R/C elements. A further R/Ccombination is wired between Output resp.Supply Ground and the ground of the housing.This avoids interferences due to a floatinghousing.

    Instant output signal ( Output) and stored peakvalue (Output Peak) are simultaneously availa-ble at separate connectors. The reset of thepeak value occurs simultaneously with theReset of the charge amplifier input.

    The inputs Operate and RangeII are controlledthrough optocouplers (electrical isolation).

    An unstabilized DC voltage of 18 ... 36 V suf-fices for the Type 5039A. Required currentapprox. 30 mA.

    ApplicationThe miniature charge amplifier Type 5039A canbe used thanks to its rugged and shock-proofconstruction in industrial applications with allkinds of piezoelectric sensors connected.

    The output signals can for instance be wired toindustrial controls and then be processed.

    The tight housing, the shock-proof constructionand the unstabilized power supply allow to usethe charge amplifier in manufacturing machi-nes, in vehicles and for many other applica-tions.

    3

    Kistler Instrumente AG, CH-8408 Winterthur, Switzerland, Tel. (052) 224 11 11 Kistler Instrument Corp., Amherst, NY 14228-2171, USA, Phone (716) 691-5100

    (Option: Output 420 mA)

    0 0 0 - 3

    0 3 m - 1

    1 . 0

    1

    ( D B 1 1

    . 5 0 3 9 m

    )

  • 8/12/2019 kistler anayzer

    4/4

    Ordering Code

    Scope of delivery Connector 8-pole

    DIN 45326 Type 1500A57

    Accessories Coupling

    BNC neg. TNC pos. Type 1709

    The above order designation can besupplemented by modification: Y36 currentoutput 420 mA instead of output Peak.

    4

    Bestellbezeichnung

    Lieferumfang Stecker 8-polig

    DIN 45326 Typ 1500A57

    Zubehr bergangskupplung

    BNC neg. TNC pos. Typ 1709

    Obige Bestellbezeichnung kann durchModifikation ergnzt sein: Y36 Stromausgang4-20 mA anstelle Output Peak.

    Dsignation de commande

    Etendue de la fourniture Connecteur 8 ples

    DIN 45326 Typ 1500A57

    Accessoires Coupleur

    BNC ng. TNC pos. Type 1709

    La rfrence de commande ci-dessus peuttre complte par la modification suivante:Y36 sortie de courant 4-20 mA la placede output Peak.

    Miniatur- Amplificateur de charge Miniature 5039A v v vLadungsverstrker miniaturis Charge Amplifier

    Range I (kalibriert) Range I (talonne) Range I (calibrated)

    50'000 pC 50'000 pC 50'000 pC 120'000 pC 20'000 pC 20'000 pC 2gemss Bestellung selon commande according to order 3

    Range I / Range II Range I / Range II Range I / Range II

    10 10 10 14 4 4 22 2 2 3

    Charge Input Charge Input Charge Input

    TNC neg. (fr IP-65) TNC ng. (pour IP-65) TNC neg. (for IP-65) 1BNC neg. BNC ng. BNC neg. 2

    Abmessungen / Dimensions / Dimensions

    Kontaktbelegung im SteckerAffectation des broches de fichesPin assignement in the connector

    0 0 0 - 3

    0 3 m - 1

    1 . 0

    1

    ( D B 1 1

    . 5 0 3 9 m

    )