jet engine turbine

8/8/2019 Jet Engine Turbine

1/16

Physical MetallurgyDesign alloys for aircraft engine.


2/16

Introduction

When we design alloys for aircraft, we have to consider many kinds ofconditions. They depend on the part of aircraft. Our team choose engine alloys

for our topic and especially We choose turbine alloys. A turbine is a machine orengine which uses a stream of air, gas, water, or steam to turn a wheel andproduce power. Those three facts need to be regarded for turbine alloys. Firstly,the property of turbine alloy must have high strength and high-temperaturestrength, because it spins very rapidly. Secondly, the cost of material need to beregarded. Thirdly, the weight of material need to be regarded, because heavy

aircraft needs lots of fuel. We are going to consider those three factors.


3/16

Definition.

An aircraft engine is a propulsion system for an aircraft.Aircraft engines are almost always a type of lightweight internalcombustion engine.

Requirement for aircraft engine

reliable lightweight powerful

small and easily streamlined repairable fuel efficient


4/16

Problems of materials applied aircraft engine

1) Low room temperature ductility.2) Creep resistance and fracture toughness become lower as room

temperature ductility increases due to changing of microstructure.3) Above 800, there is the problem of oxidation resistance.

4) Shortage of datum.5) High cost to manufacture.

FYI : Changing of materials applied aircraft.

1) Wood.2) Aluminum alloy.3) Titanium alloy.4) Compo-site material.


5/16

Design alloys for aircraft engine.

1) Reliable2) Lightweight3) Powerful.4) Fuel efficient to give the aircraft the range the design requires.5) Capable of operating at sufficient altitude for the aircraft.6) Safety.7) Environmental consideration.8) Economical consideration.


6/16

Jet Engine

Google Research jet engine image

(http://www.free-online-private-pilot-ground-school.com/turbine-engines.html )


7/16

http://video.naver.com/2008111918405323069

http://blog.naver.com/dreamline20?Redirect=Log&logNo=130005560138&vid=0

Jet Engine Media player


8/16

1)Iron Alloys

1. Pure iron2. Carbon steelC, Mn, P, S, Ni, Cr, Mo

2) Aluminium Alloys

1. 99% Pure Aluminium2. Al - Cu (4.4%)3. Al - Cu (4.0%) - Mg(1-1.5%) - Si(0.5%) - Mn(0.5-1%)4. Duralumin + Mg(0.5%-1.5%)5. Al - Mn : It has good corrosion resistance.6. Al - Mn(1.2%) : It has high internal force.7. Al - Mg(2.5%)3) Magnesium Alloys

4) Titanium Alloys

Considerable Metal Element


9/16

Turbine - Temperature

Kim Mok-soon, High Temperature Metallic Materials, Inha, 2004


10/16

*NIMONIC alloy 75(Ni 80.0, Cr 19.5)

*NIMONIC alloy 80A(Ni 76.0, Cr 19.5, Ti 2.4, Al 1.4)

*NIMONIC alloy 90 / NIMOLOY alloy PK37(Ni 60.0, Cr 19.5, Co 16.5, Ti 2.5, Al 1.5)

Design new turbine alloys


11/16

NIMONIC alloy 90

(93%)

Ni 60 * 0.93 55.800

Cr 19.5 * 0.93 18.135

Co 16.5 * 0.93 15.345

Ti 2.5 * 0.93 2.325

Al 1.5 * 0.93 1.395

FeC (3%)

Fe 3 * 0.996 2.988

C 3 * 0.004 0.012

Mg (4%) Mg 4.000

*Jet Engine - Turbine


12/16


*Turbine - Structure


13/16


*Turbine - material


14/16

*Design A New Turbine Alloys For Aircraft

As We mentioned about this project, it's very hard to design new alloys,so We are going to design a new turbine alloy which is based on 93%of NIMONIC alloy 90. We choose that 7% of (FeC - Mg) alloy intothe NIMONIC alloy 90. FeC is cheap and it has high strength. Mg isvery light. That is why, they can cover their short points each others.Following table is a final ratio of new turbine alloy.


15/16

Conclusion

We tried to find out appropriate material of aircraft, and considered suchas high strength and high-temperature strength, cost of material and theweight of material. We tried to add (FeC - Mg) alloy into the NIMONICalloy 90. FeC is heavy but Mg is light. Mg has low hardness but FeC hashigh strength. In addition, both materials are cheaper than Ni (which is

main material of NIMONIC alloy 90).(Ni) U$/ton 8,810 (Mg) U$/ton 3,950( Base metal, Minor metal http://blog.naver.com/bizdsk?Redirect=Log&logNo=40056770901)

However, our knowledge is not enough to know about everything, and it'sa kind of assumption. The reason is why, it can't be used directly forreal aircraft. It must be verified by correct experiment. However, We

hope that this report is a new attempt of aircraft material experiment.


16/16

Thank You!!

By 1Group

jet engine turbine

Documents