informal document no.grb-47-4
DESCRIPTION
Informal document No.GRB-47-4 (47th GRB, 19-21 February 2008 Agenda item 3 (a) - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/1.jpg)
Informal document No.GRB-47-4 (47th GRB, 19-21 February 2008 Agenda item 3 (a)
CLEPA presentations supporting justifications of informal
documents GRB-47-2 and GRB-47-3, proposing
amendments to R51 and R59.
![Page 2: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/2.jpg)
1. Absorbing fibrous materials2. Noise reduction systems with
variable geometry3. New driving-by test of R51 in R594. Particularities for automatic
transmission5. Static noise test
Content
![Page 3: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/3.jpg)
1. Presentation on absorbing fibrous materials. Introduction of the concept of component design family. Influence of the various silencer characteristics on the fibrous material life expectancy.
![Page 4: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/4.jpg)
Current legislation
• Exhaust systems containing fibrous materials
• Wool retention should be demonstrated by:– Continuous road operation for 10.000 km– Conditioning on a engine bench– Conditioning by pulsation (2500 cycles)
![Page 5: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/5.jpg)
• Continuous road operation for 10.000 km• The vehicle should be representative of the type in
respect of which type approval is requested
• Conditioning on a engine bench / Conditioning by pulsation (2500 cycles)
• The engine should be of at least the same cylinder capacity and rated power maximum.
Current legislation
![Page 6: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/6.jpg)
Conditioning by pulsation on 1.6 litre petrol engine
0
50
100
150
200
250
300
350
400
450
500
550
600
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Time( seconds)
gas
tem
per
atu
re(°
C)
0
20
40
60
80
100
120
140
160
180
200
bac
kpre
ssu
re(m
bar
)
gastemp [Deg C] backpress [mbar]
Gas temperature about 540°C
Test data : Conditioning by pulsation
![Page 7: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/7.jpg)
Temperature resistance fibrous materials
• Fibrous materials used in exhaust systems may have different temperature resistance characteristics :
Type A 570°C
Type B 650°C
Type C 650°C
Type D 780°C
Type E 725°C
Type F 650°C
Type G 600°C
Limit of use
![Page 8: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/8.jpg)
Conditioning by pulsation
• The result of the test may depend on the type of the fibers used (e.g. basalt wool, E type wool, Biosil wool, etc)
![Page 9: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/9.jpg)
Conditioning by pulsation
• Further parameters which could influence the result of the test :– Binder material specifications– Average fiber dimensions (thickness, length)– Minimum bulk material packing density (kg/m³)
![Page 10: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/10.jpg)
Pulsation resistance fibrous materials• The exhaust gasses in contact with the
fibrous material have or have not a net gas flow through this material– Straight-through flow silencer
– Silencer with flow through the fibrous material
![Page 11: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/11.jpg)
Conditioning by pulsation
• The presence of a net gas flow through the fibrous materials may influence the test result.
![Page 12: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/12.jpg)
• Definition of the concept of a «component design family» based on the above mentioned relevant design characteristics.
°°°°°°°°°°°°°°°°°°°°°
Proposal
![Page 13: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/13.jpg)
2. Presentation on the concept of
« noise reduction systems with variable geometry »
with regards to the implications of ASEP within R59. This includes data on the potential effects of valves in exhaust systems.
![Page 14: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/14.jpg)
Valves in exhaust systems : general overview of possible acoustical efficiency improvements
Flow noise
Engine noise
Back pressure
Passive exhaust systems
Exhaust systems with a valve
Passive exhaust systems
Exhaust systems with a valve
![Page 15: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/15.jpg)
• Valve closed at low exhaust gas volume flow
• valve opens automatically at high exhaust gas volume flow
Example of a silencer equiped with an auto-actuated valve
![Page 16: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/16.jpg)
Example 1: FLOW NOISE REDUCTION(engine noise and backpressure unchanged)
6 dB
Valve opens here
Passive exhaust system
Exhaust system with a valve
![Page 17: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/17.jpg)
Example 2: ENGINE NOISE REDUCTION(flow noise and backpressure unchanged)
Valve opens here
Passive exhaust system
Exhaust system with a valve
![Page 18: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/18.jpg)
Example of an exhaust system equipped with an auto-actuated valve and with BY-PASS OF THE REAR SILENCER
Valve
by-passing the rear silencer
at high rpm’s
Catalytic
converters
Front silencer Rear silencer
![Page 19: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/19.jpg)
View on the measured prototype exhaust system
Valve
by-passing the rear silencer
at high rpm’s
Catalytic
converters
Front silencer Rear silencer
![Page 20: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/20.jpg)
Test results
by pass closed
by pass open
Switch point
![Page 21: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/21.jpg)
Test results
• Campbell diagram: colours indicate sound level
frequency [Hz]
Eng
ine
spee
d [r
pm]
by pass closed by pass open
frequency [Hz]
dB(A)
70
20
dB(A)
70
20
6000
1000
0 5000 0 5000
![Page 22: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/22.jpg)
Conclusions
• The examples clearly show that the technology of noise reduction systems with a variable geometry may have a very positive contribution to exhaust noise abatement.
• But, by inversing the valve commands in the example which was shown, a very negative result could also be achieved.
• CLEPA proposes that for replacement exhaust systems, containing components with variable geometry, the technical service may request to verify the acoustic noise reduction functionality by performing the ASEP tests.
![Page 23: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/23.jpg)
Conclusions
• A large number of passive replacement exhaust systems (fixed geometry) are currently under test. So far all test results have shown remarkable compliance with the ASEP requirements. These results will be shown during the meeting. The testing program continues and CLEPA will report on the conclusions in the ASEP working group.
°°°°°°°°°°°°°°°
![Page 24: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/24.jpg)
3. Recall of the presentation given by CLEPA on the application in R59 of the new driving by test method of R51.
![Page 25: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/25.jpg)
Conditions of measurement• Tyres
– The use of special noisy tyres is not allowed in the comparison test because of the potential acoustical masking effect on the exhaust noise. Only tyres in line with the legal requirements for in traffic use are acceptable for the comparison test.
• Environmental temperature– No limitation on the minimum environmental
temperature has been set. The influence of temperature on exhaust noise contribution being minimal.
![Page 26: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/26.jpg)
Conditions of measurement• Measurement accuracy
– The current R59 regulation results in some practical inconsistensies and confusions with regard to the measurement accuracy and rounding off practice to the nearest integer dB(A) value.
CLEPA proposes a simplified and uniform rule, taking into account the 1 dB(A) measurement inaccuracy.
• Test vehicle acceptability– A vehicle is acceptable as a test vehicle if it satifies the
requirements for COP. This rule will bring R59 in line with directive EC 70/157.
![Page 27: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/27.jpg)
Conclusion
• The new driving-by test method R51.03 and the current test method R51.02 show practically identical relevance when applied to the comparison test between OE and replacement parts in R59.
°°°°°°°°°°°°°°°°°°°°°°°°°°°°°
![Page 28: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/28.jpg)
4. Presentation about the particularities of automatic transmission for the drive-by test in R59.
![Page 29: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/29.jpg)
Automatic transmission• In Par. 3.1.2.1.4.2 of R51 concerning vehicles
with automatic transmission tested with non-locked gear ratios, it is indicated that it is permitted for the car manufacturers to establish and use electronic and/or mechanical devices to prevent a downshift. This is unpractical for replacement parts approval tests.The following results show that a comparison test allowing a downshift gives similar comparison results as a test without downshift.
![Page 30: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/30.jpg)
5. Justification for the CLEPA amendment proposal of the static noise test procedure in R51/R59.
![Page 31: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/31.jpg)
Static noise test
• The following graph illustrates the poor reproducebility of the current static noise test. This results in problems with in use compliance testing. A slightly modified testing procedure will prevent this inconsistency.
![Page 32: Informal document No.GRB-47-4](https://reader034.vdocuments.mx/reader034/viewer/2022051316/56814da4550346895dbaffae/html5/thumbnails/32.jpg)
70
72
74
76
78
80
82
84
86
88
90
70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
B2- Car measured type approval value
B3-
Mea
sure
d v
alu
e w
ith
OE
Sile
nce
r
STATIC NOISE OEM TYPE APPROVAL TESTS