industra-coat epoxy & urethane kit · industra-coat epoxy & urethane kit application...

Toll-Free: (877) 738-7325 9042 Cotter StreetLocal: (614) 754-4777 Green Meadows Commerce CenterFax: (614) 754-4778 Lewis Center, OH 43035Emergency: (800) 424-9300 Email: [email protected] www.vseal.com

Industra-Coat Epoxy & Urethane KitApplication Outline & Tips

PREPARATIONSubstrate should be very clean, dry with little to no hydrostatic pressure, neutral to slightly alkaline, and have a surface profile equivalent to a 200-300 grit sand/grind. Recommended application temperature is 70 degrees F (see cure schedule for details).

STEP 1: INDUSTRA-COAT 3015 EPOXY PRIMERMix Industra-Coat 3015 Part A and Industra-Coat 3015 Part B at a mix ratio of 4 Parts A to 1 Part B. Stir thoroughly with a jiffy mixer at a slow speed to avoid air entrapment. Pot life is approximately 60 minutes under normal conditions.Roll on Industra-Coat 3015 with a 1/4” or 3/8” nap roller. Adhesive and epoxy roller covers are recommended for best results. Coating should be applied at 5-7 mils wet thickness (1 mil = 1/1000th of an inch). Coverage rate at 6 mils wet thickness is 267 ft.2 per gallon.

Wait 8-12 hours for Industra-Coat 3015 Epoxy Primer to be print free and walkable. Generally, no longer than 24-48 hours should pass between coating applications to maintain chemical bond.(If more than 24-48 hours passes between coatings, sanding/grinding with 200-300 grit may be necessary to achieve mechanical bond in place of chemical bond)

STEP 2: INDUSTRA-COAT 3321 URETHANE TOPCOAT (*or Industra-Coat 3322 Low VOC substitute)Mix Industra-Coat 3321 Part A and Industra-Coat 3321 Part B at a mix ratio of 2 Parts A to 1 Part B. Stir thoroughly with a jiffy mixer at a slow speed to avoid air entrapment. Pot life is 2-4 hours under normal conditions.Roll on Industra-Coat 3321 with a 1/4” or 3/8” nap roller. Adhesive and epoxy roller covers are recommended for best results. Coating should be applied at 3-5 mils wet thickness (1 mil = 1/1000th of an inch). Coverage rate is 320-500 ft.2 per gallon at 3-5 mils wet thickness.

WALKABLE: 14-24 HoursFULL CURE: 3-5 Days

V-SEAL Concrete Sealers (877) 738-7325 ~ [email protected]

IINNDDUUSSTTRRAA--CCOOAATT ##33001155 WWAATTEERR BBAASSEEDD EEPPOOXXYY PPRRIIMMEERR

PRODUCT DESCRIPTION: Industra-Coat #3015 is a two component water based epoxy coating that exhibits excellent characteristics that rival solvent based products. #3015 has

superb chemical resistance, abrasion resistance, and substrate penetration.

RECOMMENDED FOR: Recommended for priming or coating concrete, wood or masonry. This product can withstand exposure to many common solvents and chemicals.

SOLIDS BY WEIGHT: Mixed = 53% (colors); 45% (clear); (+, - 2%)

SOLIDS BY VOLUME:

Mixed = 41% (colors); 36% (clear); (+, - 2%)

VOLATILE ORGANIC CONTENT: Colors = 1.01 pounds per gallon (mixed)

Clear = 1.0 pounds per gallon (mixed)

STANDARD COLORS:

Off white, light gray, medium gray, tile red, beige, and amber clear.

NOTE: The clear (gardner 11) is not water clear and is not suitable for

topcoating over previously color coated floors. The clear is suitable as

a primer or concrete sealer only.

RECOMMENDED FILM THICKNESS: 5 -7 mils per coat wet thickness (yields 2-3 mils dry)

COVERAGE PER GALLON: 229 to 320 square feet @ 5-7 mils wet thickness

PACKAGING INFORMATION 2 gallon and 5 gallon kits (volume approx.)

MIX RATIO: Colors= 8.55# part A (.80 gallons, approximate) to 1.75# part B (.20

gallons, approximate)

Clear= 6.55# part A (.80 gallons, approximate) to 1.90# part B (.20

gallons, approximate)

SHELF LIFE:

1 year in unopened containers

FINISH CHARACTERISTICS: Satin gloss (40-80 at 60 degrees @ Erichsen glossmeter)

ABRASION RESISTANCE: Taber adrasor CS-17 calibrase wheel with 1000 gram total load and

500 cycles = 54 mg loss

IMPACT RESISTANCE:

Gardner Impact, direct = 50 in.lb. (passed)

FLEXIBILITY: No cracks on a 1/8” mandrel

ADHESION:

425 psi @ elcometer (concrete failure, no delamination)

VISCOSITY: Mixed = 900-1200 cps (colors); 400-900 cps (clear) (typical)

DOT CLASSIFICATIONS: Not regulated

CURE SCHEDULE: (70F) pot life – 1 gallon volume …………………...…..... 1.0 – 1.5 hours

tack free (dry to touch)………………………..………… 5-8 hours

recoat or topcoat.....…………………………………..... 7-10 hours

light foot traffic...……………………………...……....16-24 hours

full cure (heavy traffic)... ………………………………....2-7 days

APPLICATION TEMPERATURE: 55-90 degrees F with relative humidity below 75%

CHEMICAL RESISTANCE: REAGENT RATING

acetic acid 5% B

xylene B

mek A

gasoline B

10% sodium hydroxide C

50% sodium hydroxide B

10% sulfuric B

10% hrdochloric acid B

20% nitric acid A

ethylene glycol C Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term

splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive chemical resistance information is available through your sales representative.

PRIMER: None required.

TOPCOAT: Optional – Many products are suitable as topcoats including multiple

coats of this product. For added chemical resistance, color stability or

UV stability, topcoat with a suitable urethane.

LIMITATIONS: * Color or gloss may be affected by humidity, low temperatures,

chemical exposure or sodium vapor lighting.

* May yellow in the presence of UV light without proper topcoat.

* For best results use a 1/4” or 3/8” nap roller.

* Slab on grade requires moisture barrier.

* Substrate temperature must be 5°F above dew point.

* All new concrete must be cured for at least 30 days

*Product color will vary from batch to batch. Use only product from

the same batch for an entire job.

* Improper mixing or too thick of an application may result in product

failure.

* Light or bright colors (white, safety colors etc.) may require multiple

coats or a topcoat to achieve a satisfactory hide, depending on the

substrate.

* Physical properties listed on this technical data sheet are typical

values and not specifications.

* See reverse side for limitations of our liability and warranty.

* See reverse side for application instructions.


MIXING AND APPLICATION INSTRUCTIONS (#3015) 1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous

storage should be between 60 and 90 degree F. Keep from freezing.

2) SURFACE PREPARATION: Surface preparation will vary according to the type of complete system to be applied. For a one or two

coat thin build system (3-10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved.

For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign

contaminants and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the

concrete has an appropriate vapor barrier. This can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges.

If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate does not show signs of eventual hydrostatic pressure

problems that may later cause disbanding. However, this product can be applied to a damp floor as long as there are not standing puddles.

It is advised to conduct a small test to verify adhesion prior to full application.

3) PRODUCT MIXING: This product comes pre-packaged by weight. Kits should be mixed in their entirety. If partial kits are to be

used, refer to the front of this technical data for proper weight mix ratios. After the two parts are combined, mixes well with slow speed

mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. This product is an emulsion product and

should be mixed well before using.

4) PRODUCT APPLICATION: The mixed material can be applied by brush, roller or HVLP sprayer. Maintain temperatures within the

recommended ranges during the application and curing process. Apply material with relative humidity within the parameters shown on

the technical data. When the end of the pot life has been reached, you will find that the material becomes hard to apply and will actually

tend to roll back up onto the roller. Do not try to continue application when the coating has reached this step. Applications made at

different times with differing environmental conditions, may show slight variations in gloss.

5) RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that all of the solvents and water

have evaporated from the coating during the curing process. The information on the front side are reliable guidelines to follow.

However, it is best to test the coating before recoating or topcoating. This can be done by pressing on the coating with your thumb to

verify that no fingerprint impression is left. If no impression is created, then the recoat or topcoat can be started. Always remember that

colder temperatures will require more cure time for the product before recoating or topcoating can commence. Before recoating or

topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). If a blush is present, it

must be removed prior to topcoating or recoating. A standard type detergent cleaner can be used to remove any blush. Many epoxy

overlays and coatings as well as urethanes are compatible for use as a topcoat for this product as well as multiple coats of this product.

6) CLEANUP: Use PM solvent

7) FLOOR CLEANING: Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing

your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.

8) RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical

data under full cure). It is best to let the floor remain dry for the full cure cycle. READ ALL INSTRUCTIONS PRIOR TO APPLICATION. Always test a small area prior to application to evaluate appearance and to determine suitability of this product for the intended purposes. Application questions or technical information contact (877) 738-7325 or [email protected].

IMPORTANT NOTICE: When properly applied INDUSTRA-COAT products conform with surface coefficient of friction (traction) standards: OSHA >.5, ADA and

ATBCB levels of >.6 level and >.8 ramps. Anti-skit grit may be added to increase traction (see below). Due to wide variations in surface conditions, IT IS SOLELY THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF EACH FINISHED SURFACE. ANTI-SKID GRIT: Mix in anti-skid grit of up to 60 mesh at a rate of up to 15% by volume as required to conform to relevant traction standards. Continuously stir to

maintain uniform application. IT IS SOLELY THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF EACH FINISHED SURFACE.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND

LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of

our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your

own tests to determine the suitability of our product for your particular purpose. Listed physical properties are typical and should not be construed as

specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH

IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR

PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY

IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no

liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our

product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or

other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other

liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE

USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

mailto:[email protected]


IINNDDUUSSTTRRAA--CCOOAATT ##33332211 HHIIGGHH PPEERRFFOORRMMAANNCCEE UURREETTHHAANNEE

PRODUCT DESCRIPTION: Industra-Coat #3321 is a two component polyester/aliphatic polyurethane floor sealer that exhibits excellent characteristics for abrasion resistance,

chemical resistance, flexibility, weathering and UV stability.

RECOMMENDED FOR: Recommended for auto service centers, warehouses, computer rooms, laboratories, aircraft hangers, cafeterias, exterior tanks, indoor or outdoor service

and chemical exposure areas.

SOLIDS BY WEIGHT: Mixed= 60% (colors); 56% (clear) (+,-2%)

SOLIDS BY VOLUME:

Mixed= 53% (colors); 53% (clear) (+,-2%)

VOLATILE ORGANIC CONTENT: Less than 3.8 pounds per gallon

STANDARD COLORS: White, off white, light gray, medium gray, tile red, beige, and clear

RECOMMENDED FILM THICKNESS: 3-5 mils per coat wet thickness (yields 2-3 mils dry)


PACKAGING INFORMATION 3 gallon and 15 gallon kits 3 gal kit= 2 gallons part A (10.5#/gal-

colors) or (8.75#/gal-clear) and 1 gallon part B (8.5#/gal.) (weights and

volumes approximate)

MIX RATIO: 2 parts A to 1 part B by volume

SHELF LIFE: 1 year

FINISH CHARACTERISTICS: High gloss (>80 at 60 degrees @ Erichsen glossmeter)

ABRASION RESISTANCE: Taber abrasor CS-17 calibrase wheel with 1000 gram total load and

500 cycles = 20.0 mg loss

IMPACT RESISTANCE: Gardner Impact, direct & reverse = 160 in. lb. (passed)


ADHESION: 360 psi @ elcometer (concrete failure, no delamination)

VISCOSITY: Mixed = 200-400 cps (typical, most colors)

DOT CLASSIFICATIONS: Part A “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII”

Part B “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII”

HARDNESS: Shore D = 72

CURE SCHEDULE: (70°F) pot life – 1 1/2 gallons volume ...…..………………………….... 2-5

hours

tack free (dry to touch)…………...…………………………...…2-4

hours

recoat or topcoat.....…………….………..…………………....... 4-8

hours

light foot traffic...………………………………………..……14-24

hours

full cure (heavy traffic)... …………………..……………...…....3-5

days

APPLICATION TEMPERATURE: 45-90 degrees F

CHEMICAL RESISTANCE: REAGENT RATING acetic acid 5% C

xylene E mek B

methyl alcohol B

gasoline D 10% sodium hydroxide E

50% sodium hydroxide D

10% sulfuric D 10% hydrochloric acid D

20% nitric acid C ethylene glycol D

Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term

splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive chemical resistance information is available through your sales representative.

TOPCOAT: None recommended

LIMITATIONS: *Colors or gloss may be affected by high humidity, low temperatures,

chemical exposure, or exposure to lighting such as sodium vapor lights.

*For best results use a high quality 3/8” nap roller.

*Slab on grade requires moisture barrier.

*Substrate temperature must be 5°F above dew point.

*All new concrete must be cured for at least 30 days.

*Physical properties are typical values and not specifications

*Light or bright colors (white, safety yellow, etc.) may require multiple

coats or a suitable color coordinated primer to achieve a satisfactory

hide.

*Tire contact may cause staining and discoloration (generally new

tires).

*Colors may vary from batch to batch, therefore, use only product from

the same batch for an entire job.

*See reverse side for application instructions.

*See reverse side for limitations of our liability and warranty.


MIXING AND APPLICATION INSTRUCTIONS (#3321) 1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous

storage should be between 60 and 90 degree F.



For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign


concrete is dry; this can be done by placing a 4’ X 4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the

substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good

method to determine if any hydrostatic pressure problems exist that may later cause disbonding.

3) PRODUCT MIXING: This product has a two to one mix ratio by volume- merely mix two gallons of part A with 1 gallon of part B.

After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed

and streak free. Avoid whipping air into the coating. Improper mixing may result in product failure.

4) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. Maintain temperatures within the recommended

ranges during the application and curing process. Properly prime the substrate. It is best to maintain a wet edge to avoid roller marks.

Direct sunlight or high temperatures may cause visible roller marking during application. Too thick of an application may result in

solvent entrapment and product failure.

5) RECOAT OR TOPCOATING: Multiple coats of this product are acceptable. If you opt to recoat this product, you must first be sure

that all of the solvents have evaporated from the coating during the curing process. The information on the front side are reliable

guidelines to follow. However, it is best to test the coating before recoating or topcoating. This can be done by pressing on the coating

with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat can be started. Always

remember that colder temperatures will require more cure time for the product before recoating can commence. Before recoating or

topcoating, check the coating to insure no contaminants exist. If a blush or contaminants are present on a previous coat, remove with a

standard detergent cleaner. When recoating this product with subsequent coats of the urethane, it is advisable to apply the recoat before

24 hour passes. Also, it is advisable to degloss the previous coat to insure a trouble free bond.

6) CLEANUP: Use ketone solvents




data under full cure). It is best to let the floor remain dry for the full cure cycle.

READ ALL INSTRUCTIONS PRIOR TO APPLICATION. Always test a small area prior to application to evaluate appearance and to determine suitability of this

product for the intended purposes. Application questions or technical information contact (877) 738-7325 or [email protected].

IMPORTANT NOTICE: When properly applied INDUSTRA-COAT products conform with surface coefficient of friction (traction) standards: OSHA >.5, ADA and ATBCB levels of >.6 level and >.8 ramps. Anti-skit grit may be added to increase traction (see below). Due to wide variations in surface conditions, IT IS SOLELY

THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF EACH FINISHED SURFACE. ANTI-SKID GRIT: Mix in anti-skid grit of up to 60 mesh at a rate of up to 15% by volume as required to conform to relevant traction standards. Continuously stir to maintain uniform application. IT IS SOLELY THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF

EACH FINISHED SURFACE.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND

LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge.

Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the

suitability of our product for your particular purpose. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE,

EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN

FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT

SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT

INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of

our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not

purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other

liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE

MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.



IINNDDUUSSTTRRAA--CCOOAATT ##33332222 HHIIGGHH PPEERRFFOORRMMAANNCCEE ((VVOOCC CCOOMMPPLLIIAANNTT)) UURREETTHHAANNEE

PRODUCT DESCRIPTION:

Industra-Coat #3322 is a two component polyester/aliphatic polyurethane coating that exhibits excellent characteristics for abrasion

resistance, chemical resistance, flexibility, weathering, and UV stability. This product meets the VOC requirements for the newly enacted

VOC laws of New York, Pennsylvania, New Jersey, and other states as an industrial maintenance coating.

RECOMMENDED FOR: Recommended for auto service centers, warehouses, computer rooms, laboratories, aircraft hangers,

cafeterias, exterior tanks, indoor or outdoor service and chemical exposures areas.

SOLIDS BY WEIGHT: Mixed= 73% (colors); 64% (clear) (+/- 2%)

SOLIDS BY VOLUME: Mixed= 70% (colors); 60% (clear) (+/- 2%)

VOLATILE ORGANIC CONTENT: VOC content is less than 2.8 pounds per gallon (mixed)

STANDARD COLORS: white, off white, light gray, medium gray, tile red, beige, and clear.

RECOMMENDED FILM THICKNESS: 3-5 mils per coat wet thickness (yields 2-3 mils dry)


PACKAGING INFORMATION: 3 gallon and 15 gallon kits. 3 gal kit = 2 gallons part A (weight varies

by color) and 1 gallon part B (8.5#) (weights and volumes

approximate)

MIX RATIO: 2 parts A to 1 part B by volume (approximate)

SHELF LIFE: 1 year in unopened containers

FINISH CHARACTERISTICS: high-gloss (>70 at 60 degrees @ Erichsen glossmeter)

IMPACT RESISTANCE: Gardner Impact, direct & reverse=160 in lb (passed)

ABRASION RESISTANCE: Taber abrasor CS-17 calibrase wheel with 1000 gram total load and

500 cycles= 22.0 mg loss

ADHESION: 350 psi @ elcometer (concrete failure, no delamination)

VISCOSITY: Mixed= 200-600 cps (typical)

DOT CLASSIFICATIONS: Part A “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII”

Part B “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII”

HARDNESS: Shore D= 62


CURE SCHEDULE: (70°F) pot life – (1 1/2 gallon volume)……………........………...…..2-4 hours

tack free (dry to touch)………………...……...………………3-5 hours

recoat or topcoat.....…………….……......................................5-9 hours

light foot traffic...…………………………..……............…14-24 hours

full cure (heavy traffic)... ………………….…………...….......3-5 days

APPLICATION TEMPERATURE: 45-90 degrees F.

CHEMICAL RESISTANCE: REAGENT RATING acetic acid 5% B

xylene D

mek A methyl alcohol B

gasoline D

10% sodium hydroxide E 50% sodium hydroxide D

10% sulfuric D

10% hydrochloric acid C 20% nitric acid B

ethylene glycol D

Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive

chemical resistance information is available through your sales representative.

PRIMER: Recommend 3143/3144, 3154VOC or 3015

TOPCOAT: None recommended.

LIMITATIONS: *Colors or clarity for clear may be affected by high humidity, low

temperatures, or chemical exposure.

*For best results use a high quality 3/8” nap roller.

*Slab on grade requires moisture barrier.

*Substrate temperature must be 5°F above dew point.

*All new concrete must be cured for at least 30 days.

*Light or bright colors (white, safety yellow, etc.) may require

multiple coats or a suitable color coordinated primer to achieve a

satisfactory hide.

*Colors may vary from batch to batch, therefore, use only product

from the same batch for an entire job.

*Tire contact may cause discoloration or staining.

*Physical properties are typical values and not specifications.

*See reverse side for application instructions.

*See reverse side for limitations of our liability and warranty.


MIXING AND APPLICATION INSTRUCTIONS (#3322)

1) PRODUCT STORAGE: Store product in an area as to bring the material to normal room temperature before using. Continuous

storage should be between 60 and 90 degrees F.



For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast) All dirt, oil, dust, foreign


concrete is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the

substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good

method to determine if any hydrostatic pressure problems exist that may later cause disbonding.

3) PRODUCT MIXING: This product has a two to one mix ratio by volume- merely mix two gallons of part A with 1 gallon part B.

After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed

and streak free. Avoid whipping air into the coating. Improper mixing may result in product failure.

4) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. Maintain temperatures within the recommended

ranges during the application and curing process. Properly prime the substrate. It is best to maintain a wet edge to avoid roller marks.

Direct sunlight or high temperatures may cause visible roller marking during application. Too thick of an application may result in

product failure. Exposure to certain types of lighting such as sodium vapor lights may cause the product to discolor.

5) RECOAT OR TOPCOATING: Multiple coats of this product are acceptable. If you opt to recoat this product, you must first be sure

that all of the solvents have evaporated from the coating during the curing process. The information on the front side are reliable

guidelines to follow. However, it is best to test the coating before recoating or topcoating. This can be done by pressing on the coating

with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat can be started. Always

remember that colder temperatures will require more cure time for the product before recoating can commence. Before recoating or

topcoating, check the coating to insure no contaminants exist. If a blush or contaminants are present on a previous coat, remove with a

standard detergent cleaner. When recoating this product with subsequent coats of the urethane, it is advisable to apply the recoat before

24 hours passes. Also, it is advisable to degloss the previous coat to insure a trouble free bond.

6) CLEANUP: Use ketone solvents




data under full cure). It is best to let the floor remain dry for the full cure cycle.

READ ALL INSTRUCTIONS PRIOR TO APPLICATION. Always test a small area prior to application to evaluate appearance and to determine suitability of this

product for the intended purposes. Application questions or technical information contact (877) 738-7325 or [email protected]. IMPORTANT NOTICE: When properly applied INDUSTRA-COAT products conform with surface coefficient of friction (traction) standards: OSHA >.5, ADA and

ATBCB levels of >.6 level and >.8 ramps. Anti-skit grit may be added to increase traction (see below). Due to wide variations in surface conditions, IT IS SOLELY

THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF EACH FINISHED SURFACE. ANTI-SKID GRIT: Mix in anti-skid grit of up to 60 mesh at a rate of up to 15% by volume as required to conform to relevant traction standards. Continuously stir to

maintain uniform application. IT IS SOLELY THE OBLIGATION OF THE APPLICATOR TO TEST SURFACE COEFFICIENT OF FRICTION (TRACTION) OF

EACH FINISHED SURFACE.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of

our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make

your own tests to determine the suitability of our product for you particular purpose. Listed physical properties are typical and should not be construed as

specifications. NO WARRANTY IS MADE, EXPRESSED, OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON

WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED,

THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO

WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We

shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the

replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not

purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or

assume any other liability on our behalf with any sales of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL

INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY

HARM.


Actual colors may vary from colors shown. Coatings also available in Clear, White, & Black.

Special colors and Safety colors available upon request. Colors may vary from batch to batch and product to product.

Flooring Color Chart - Epoxy Coatings Color Selections

Light Blue

Blue

Tan Brown

Fazor Tan

Green

Light GrayMedium Gray

Dark Gray

Off White

BeigeTile Red

Traffic Yellow

Charcoal Gray

SE Camel

Safety Yellow

System #1 System #2 System #3 System #4

System #5 System #6A System #7 System #8A

System #9 System #10 System #11 System #12

System #13

YOU CAN ALSO CREATE YOUR OWN CUSTOM BLENDS! COLORS SHOWN HERE ARE COMPUTER GENERATED AND MAY VARY GREATLY FROM ACTUAL COLORS PLEASE CONTACT YOUR SALES REPRESENTATIVE FOR PHYSICAL SAMPLES.

System #1 25 Red, 25 White, 25 Gray, 25 Black

System #2 50 Blue, 25 Gray, 25 White, 25 Black

System #3 25 Black, 25 White, 25 Gray, 25 Tan

System #4 25 Orange, 25 White, 25 Tan, 25 Beige

System #5 50 White, 50 Gray, 25 Black

System #6A 30 Cocoa Brown, 30 Tan (607), 20 White, 10 Beige

System #7 50 Orange, 25 Black, 25 White

System #8A 80 Beige, 20 Tan (602), 10 Black

System #9 75 White, 25 Blue, 25 Black, 25 Gray

System #10 50 Black, 50 Blue

System #11 25 Beige, 25 White, 25 Green

System# 12 50 Black, 50 White

System #13 25 Green, 25 Black, 25 White, 25 Gray

CREATE YOUR OWN CUSTOM BLENDS!

industra-coat epoxy & urethane kit · industra-coat epoxy & urethane kit application...

Documents