graphic communicationhomework design and technology department page 1 10 mm = 1 m 100 mm = 10 m use...
TRANSCRIPT
Page 1
Graphic Communication Homework
Design and Technology Department
10 mm = 1 m100 mm = 10 m
Use the scale given above to obtain the following information. Write your answers in your jotter.
1.the height to the eaves.2.the height to the ridge.3.the height to the door. 4.the dimensions of window A. (length x height)5.the dimensions of window B. (length x height)6.the dimensions of window C. (length x height)7.the length of the house.You can use either your rule to measure the sizes or
you could use a pair of compasses to lift the sizes.
Homework Task 1 Unit 1 - Measurement
Page 2
Graphic Communication Homework
Design and Technology Department
The diagram above shows a toy road roller drawn actual size. Measure and record the following dimensions in your jotter:
1. diameter of front roller.2. diameter of flywheel.3. diameter of back wheel.4. height of top of canopy from the ground. 5. length of canopy.6. distance between centre of flywheel and the
centre of the back wheel. 7. height to top of funnel from the ground.
Homework Task 2 Unit 1 - Measurement
Page 3
Graphic Communication Homework
Design and Technology Department
Homework Task 3Unit 2 - Isometric Sketching
Complete this work on Isometric Grid paper. Draw the rectangular block shown opposite. The dimensions are:Length - 9 squaresBreadth - 4 squaresHeight - 5 squares
Homework Task 4Unit 2 - Isometric Sketching
Complete this work on Isometric Grid paper. Draw the rectangular block shown opposite. The dimensions are:Length - 9 squaresBreadth - 4 squaresHeight - 5 squares
Page 4
Graphic Communication Homework
Design and Technology Department
Homework Task 5Unit 2 - Isometric Sketching
Complete this work on Isometric Grid paper. Draw the rectangular block shown opposite. The dimensions are:Length - 9 squaresBreadth - 4 squaresHeight - 5 squares
Page 5
Graphic Communication Homework
Design and Technology Department
Homework Task 6Unit 3 - Isometric Drawing
1. Name the piece of drawing equipment shown below:
2. Name the piece of drawing equipment shown below and the angle used to draw an isometric.
3. What are the 3 main dimensions used in isometric drawing.
a) L _ _ _ _ _ b) B _ _ _ _ _ _ c) H _ _ _ _ _
Page 6
Graphic Communication Homework
Design and Technology Department
Homework Task 7Unit 4 – Introduction to Orthographic Projection
1. What is orthographic projection?
2. What is 3rd Angle Projection?
3. Make a sketch of the symbol which shows that a drawing has been produced in 3rd Angle Projection.
4. Sketch the orthographic projection shown below and then name each of the 3 views.
Page 7
Graphic Communication Homework
Design and Technology Department
Homework Task 8Unit 4 – Introduction to Orthographic Projection
1. In your jotter write down the code letter of the objects shown below. Study each one and imagine you are looking in the direction of the arrow. Look at the views in the bottom half of the page and match each view to one of the lettered objects you have listed.
Page 9
Graphic Communication Homework
Design and Technology Department
Homework Task 9Unit 5 - Orthographic Sketching
Draw the four views of the coloured block in the direction of the arrows. Use the squares in your jotters as a guide for measuring and drawing.
Leave 3 squares between each view.
Homework Task 10Unit 5 - Orthographic Sketching
Draw the four views of the coloured block in the direction of the arrows. Use the squares in your jotters as a guide for measuring and drawing.
Leave 3 squares between each view.
PLA
NELEVATIONEND
ELEVATION
PLA
NP
LAN
ELEVATION
ELEVATIONEND
ELEVATION
END
ELEVATION
PLA
NP
LAN
ELEVATION
ELEVATIONEND
ELEVATION
END
ELEVATION
Page 10
Graphic Communication Homework
Design and Technology Department
Homework Task 11Unit 5 - Orthographic Sketching
Draw the four views of the coloured block in the direction of the arrows. Use the squares in your jotters as a guide for measuring and drawing.
Leave 3 squares between each view.
PLA
NP
LAN
ELEVATION
ELEVATIONEND
ELEVATION
END
ELEVATION
Page 11
Graphic Communication Homework
Design and Technology Department
Homework Task 12Unit 6 – Orthographic Drawing
• Draw a line which would indicate a Centre Line on an Orthographic drawing.
• Draw a line which would indicate a Hidden Line on an Orthographic drawing.
3. Where on an Orthographic drawing would a Continuous Thin Line be used?
4. Where on an Orthographic drawing would a Continuous Thick Line be used?
5. Where would the following type of line be used?
Page 12
Graphic Communication Homework
Design and Technology Department
Homework Task 13Trace the symbols shown below into your jotters and add the correct colour from the descriptions below.
WARNING Risk of Danger
MANDATORY Must Do
FIRE-FIGHTING Fire Equipment Location
SAFE CONDITION The Safe Way
PROHIBITION Do Not Do
Yellow Triangle/Black BorderYellow most easily seen even in poor light. Black provides a striking contrast.
Red Square/RectangleRed is associated with fire.
White Circle/ Red Border/ Red Cross BarRed is associated with danger.
Blue CircleEasily seenGood contrast with white.
Green Square/RectangleGreen is associated with safety.
Page 13
Graphic Communication Homework
Design and Technology Department
Homework Task 14
Symbol TypesProhibition Sign Safe Condition SignWarning Sign Mandatory Sign
Name the types of symbols shown below and what information they are giving. Use the symbol types above and the possible meanings given below to assist.
1. 2. 3.
4. 5. 6.
7. 8.
Caution toxic hazard, Remove glasses, No smoking, Caution risk of fire, Eye protection must be worn, Smoking in this area only.Caution risk of explosion, Emergency stop, Caution laser beam, Pedestrians prohibited, People crossing, Caution risk of electric shock.
Page 14
Graphic Communication Homework
Design and Technology Department
Homework Task 15
• Copy or trace the colour wheel above.
• Fill in the missing colours
Yellow
Blue Red
Green Orange
Yellow Yellow Orange
Orange
Red Orange
Red Violet
Violet
Red
Blue Green
Gre
en
Yellow G
reen
Blue
Blue Violet
Violet
Page 15
Graphic Communication Homework
Design and Technology Department
Homework Task 16
• List the three primary colours
• List the tree secondary colours
• What colour is described as a hot, bold colour?
• What colour is described as a cool, serene colour?
• Green is the most _________ of all the colours.
• White is assossiated with _________.
• What colour is described as rich and regal?
Page 16
Graphic Communication Homework
Design and Technology Department
Homework Task 17
Look at the following chart:
• Who buys the most sweets in the month?• Who spends the most on fashion?• How much do boys spend on sports per month?• How much do girls spend on music per month?• How much do the boys spend per month?• How much do the girls spend per month?
Page 17
Graphic Communication Homework
Design and Technology Department
Homework Task 17
Study the pictograph below:
• What type of vehicle uses the motorway most each day?• How many motorbikes use the motorway?• How may trucks use the motorway?• Why do you think this type of graphical chart is easy to read?