government of himachal pradesh...
TRANSCRIPT
GOVERNMENT OF HIMACHAL PRADESH DEPARTMENT OF AGRICULTURE
OPERATIONAL GUIDELINES
FOR
IMPLEMENTATION
OF
PT. DEEN DAYAL KISAN BAGWAN SAMRIDHI
YOJNA
(FUNDED BY – NABARD RIDF – XIV)
PART –I (2010-11)
(PRODUCTION OF CASH CROPS THROUGH
ADOPTION OF PRECISION FARMING
PRACTICES IN POLY-HOUSES) IN
HIMACHAL PRADESH
INDEX Sr. No Items Page No.
1. Introduction 1 to 17 2. Rationale of the Project and Objectives. 3. Project Components 4. Project Areas, Beneficiaries and how to apply. 5. Role and Responsibility of Project Implementing Agency. 6. Role and Responsibility of District Nodal Officer. 7. General. 8. Monitoring and Evaluation. 9. Facilitation to the farmers. 10. Expected Outcome. 11. Annexure 1. 1. Annexure-
A Performa for maintaining beneficiary wise record 18 to 19
2. Annexure-I
Application Form for the assistance under Pt. Deen Dayal Kisan Bagwan Samridhi Yojna (Part –I)
20 to 24
3. Annexure-II
Format to be filled in by the PIA for submission to DNO for obtaining Administrative Approval of the project proposal.
25 to 26
4. Annexure-II-a
Authorization for the C/O Poly –House / Installation of Micro-Irrigation Systems / Creation of Water Source.
27 to 29
5. Annexure-II-b
Undertaking to be given by the beneficiary in the shape of affidavit to be attested by the First Class Magistrate /Notary (After receiving the sanction from DNO).
30 to 31
6. Annexure-III
Specifications for Installation of Micro-Irrigation Systems under Protected Covered area, Approved rates per Sqm covered area and Unit Costs.
32 to 33
7. Annexure-IV
Specifications of Poly –House Structures and Model-wise approved per Sqm covered area and Unit Costs.
34to 66
8. Specifications for extra- models of poly- houses structures and model –wise Approved rates per Sqm covered area along with detail of authorized companies
67 to 68
9. Drawing of various Models of Poly-houses. 69 to 110 10. Specifications for providing and Supplying of
cladding materials, Approved rates per Sqm. and list of authorized suppliers.
111 to 114
11. Specifications of G.I. Pipes 115 to 116 12. Annexure-
VI Agreement between farmer and Eligible firm / company (Service Providers) for c/o Poly-House and installation of Micro-Irrigation Systems.
117 to 118
13. Annexure NABARD Sanction including terms and conditions 119 to 126
- VII 14. Annexure-
VIII Terms and conditions to be followed/ observed by the companies shortlisted on the basis of the technical and financial bids to act as service providers for the construction of Poly –Houses and Installation of Micro-Irrigation systems i.e. Part A and Part –B
127 to 129
15. Annexure-IX
List of Companies empanelled as service providers for the year 2010-11
130 to 131
Operational guidelines of Part-I Project
1. INTRODUCTION: There is a great variation in agro-climatic conditions in the Pradesh. These
ranges from sub-humid sub tropical to dry temperate. Due to these climatic variations, varieties
of crops are grown during different periods of the year. Majority of cash crops mainly vegetables
grown in the Pradesh are exported and consumed by the neighbouring states of plains. There is
lot of demand for off season vegetables grown in the Pradesh and also there is a great export
potential.
Holdings in the Pradesh are small and the availability of main input i.e.
water is also critical owing to unevenly distribution of rainfall. During recent past, vegetable
growers in the Pradesh have suffered heavy losses due to excessive incidence of biotic and
abiotic components of the environment. In areas, which experience very heavy rainfall,
hailstorm, high velocity winds, frequent dry spells mainly due to changed patterns of weather,
vegetable growers had no choice but to leave cultivation of sensitive, inputs intensive although
highly remunerative cash crops. Also due to extreme climatic conditions, such as long winter
season, excessive heat, snow etc. in different parts of the Pradesh, farmers grow only one crop
with low levels of productivity. Inspite of all these constraints and limitations, the State has made
remarkable progress in diversifying area from traditional food grains to high value vegetable
crops which fetch high income to the farmers. Annually about 10 lakh tonne vegetables are
produced and marketed within and outside the State. There is great potential to diversify area
through development and creation of water potential and its economic use. There is also urgent
need to create infra-structure like protected cultivation, marketing and value addition at farm
level.
Vegetables in general and green leafy vegetables in particular provide
essential minerals, vitamins and thus form vital component of human diet. Also there is more
demand for safe and quality farm fresh products.
In view of physiography, soil types, variability in climate, latitudes and
need of the farmers and consumers, a project on “Production of Cash Crops through Adoption
of Precision Farming Practices” was posed for NABAD loan funding under RIDF-XIV. The
same has been approved for Rs.15,491.62 lac.(Annexure-VII). The project period is four years
starting from 2008-09. Project components include construction of location specific models of
poly houses with micro irrigation facility. For this, 80% project assistance is being provided to
the farmers. Also for creation for water sources individually and collectively by a group of
farmers, 50% subsidy is being provided. With the adoption of green house/poly house
technology, farmers are growing high value cash crops like capsicum, tomato, cucumber, leafy
vegetables etc. The productivity of crops is 4 to 10 times higher and quality of produce is better.
The incidence of pests and diseases is very low with better management. The cost of production
has reduced considerably and the production is of better quality. During 2009-10, 5 lac. sq. m.
area has been brought under protective cultivation of vegetables and farmers have started
growing crops successfully. During the year 2010-11, it is envisaged to bring 9.40 lac. sq.m. area
under protected cultivation of vegetables.
The operational guidelines for Phase-I i.e. Poly Houses were issued in January,
2009 which was amended from time to time.
Taking into consideration the response of the farming community, the guidelines
have been revised and formulated so that the objectives set under the project are achieved in full.
Project assistance has been enhanced to the BPL farming families to 90% of the project cost only
for the construction of poly houses with bamboo. Some new models have also been introduced
so that farmers can derive better benefits per unit area per unit time. It is impressed upon the
project implementing agencies that cluster approach be followed and project benefits must flow
to the needy and deserving sections of the farming community i.e. small and marginal farmers.
They should get preference over other farmers. They need to be more proactive so as to achieve
the project targets timely and effectively. It is also expected that District Nodal Officers, the
Project Implementing Agencies at block level and Service Providers must formulate plans block-
wise so that project activities could be implemented smoothly in a time bound manner. The
operational guidelines have been prepared for guidance of the farmers, PIA’s and service
providers. Therefore, with complete coordination amongst the project managers, implementers,
farmers, service providers etc. the cherished goals and objectives enshrined under the project
would be achieved and the project benefits would flow to the farmers and their socio-economic
condition would improve.
2. Rationale of the Project and Objectives: With the advancement of science and technology it is possible to get assured
income by growing cash crops under protected condition. But, by and large small and marginal
farmers are resource poor and are socio-economically weak. With a view to increase socio-
economic conditions of small and marginal farmers and provide gainful employment to rural
youths and local artisans and other workers etc. project on production of cash crops through
adoption of precision farming practices (poly house and micro irrigation alongwith water source
augmentation structures) shall be implemented. The project shall be implemented in all the
Districts keeping in view the potential and target set for each district. Project components include
creation of need based infrastructure and are expected to fulfill following objectives;
- Higher productivity and better quality of produce.
- Cultivation of cash crops under protective cover will provide safeguard against
adverse weather and will enhance life span of crops.
- To get higher productivity on sustainable basis through adoption of precision farming
practices like precision planting/seeding, fertigation, micro-irrigation, weed
management, pest and disease management etc.
- Efficient inputs use and reduction in cost of production.
- Conservation of scarce resource i.e. water.
- Easy to adopt organic farming practices which are eco friendly and availability of safe
food products with full traceability.
- Farmers can advance/delay and segregate production of cash crops as per market
demand.
- Safeguard against impact of biotic and abiotic stresses.
3. Project Components (2008-09 to 2011-12) Sr.No. Component Nos. Covered area 1 Poly Houses Framed structure 16500 Nos. 14,70,200 mt2 2 Micro Irrigation (Sprinkler/Drip System
Poly Houses as per feasibility) 12,320 Nos. 14,22,000 mt2
3 Farm Tanks with poly houses as per feasibility
1700 Nos. 4,95,00,000 mt3
4 Shallow well, Shallow tube well, Deep tube well, small lift, medium lifts, pumping machinery 1 HP with poly houses as per feasibility.
950 Nos. -
5 Total cost of civil works 14546.13 lac. 6 Farmers Sensitization, contingency etc. 945.49 lac. Total Project Cost. 15491.62 lac. Up to March, 2010, about 5 lac. sq. mt. area has already been covered. 4. Project areas, beneficiaries and how to apply: Project shall be implemented for the benefit of farming community in all the
Districts of the Pradesh. District-wise targets have been fixed with regard to different project
components. However, with in district, cluster approach shall be adopted as far as possible and
preferential areas would be those which are having production constraints like heavy rainfall,
hailing , frost, high velocity winds and extreme climatic conditions like long and severe winters
etc. Among farmers, small and marginal farmers shall get preference over other farmers.
Beneficiaries:
1. Farming families directly dependent on agriculture, preference to SF/MF.
2. Unemployed educated youths having farm land shall also get priority.
3. Other farmers who are innovative and are following practices like organic farming,
INM, IPM etc.
4. Farmers of the areas having production constraints such as hailstorm, water stress,
very high rainfall, frost, severe winters etc.
All components of the projects are linked to poly house framed structures and
therefore, assistance for the construction and execution of project components like micro-
irrigation, water source development etc. shall be available on the basis of technical feasibility
report only to those farmers who avail assistance for poly house construction. Farmers who
have already constructed poly houses in areas of 1000 sq.m. or more covered area shall not be
eligible for assistance under this project,.
How to apply:
To avail project assistance, farmers shall apply to the District Nodal Officer i.e.
Deputy Director of Agriculture who is the project sanctioning authority in the district through
project implementing agency (PIA) in the development block i.e. Subject Matter Specialist on
prescribed application form (Annexure-I) duly supported with revenue record i.e. Jamabandi of
land where he wants to construct poly house structure/ water source. The PIA (Subject Matter
Specialist) shall give his report to DNO on prescribed proforma Annexure-II. Farmers shall have
to give an undertakings in the shape of an affidavit (Annexure-II(b) and will also undertake the
following:
1. That he will utilize and maintain the infrastructure created by availing project
assistance for a period of minimum 5 years.
2. That he shall use the covered area under poly house mainly for vegetable cultivation.
3. That he has not availed any financial assistance from any other department/source for
the same infrastructure to be created under this project. However, he shall be eligible
to avail assistance up to 1,000 /1008 sq. mt. total covered area.
4. That he will deposit his share i.e. 20% of cost of construction of poly house and
installation of micro irrigation system inside poly house to the service provider
(company) at the time of signing of agreement.
That in the event of departure from the above undertakings, he will be liable
to refund the whole or part of the project assistance availed to the Department of
Agriculture.
The affidavit would be on a judicial paper and must be attested by the 1st
Class Magistrate/Notary.
Farmers are at liberty to undertake construction of poly house framed
structures and installation of other related infrastructure himself or through
firm/company approved as service provider by the Govt. The list of approved
companies for construction of poly houses/MI system is enclosed as per Annexure-
V. But, the construction material to be used for the construction of poly houses and
installation of other related infrastructure i.e. Irrigation system, water storage tank,
lift etc. should be as per the specifications approved and provided in the document
enclosed at Annexure-IV. For the guidance of the farmers, models appropriate for
different areas have been approved. Also specification of construction material i.e.
G.I. pipes, poly film and micro irrigation systems have been prescribed and approved.
Farmers will not be eligible for assistance if the structures are not constructed as per
approved designs and with material of approved specifications. Project assistance
shall be released to the beneficiary after the full completion of project components
sanctioned and after verification by the Block level project implementation agency. In
view of above, it would be appropriate if farmers avail credit from any bank for a
small duration (3-5 months) in case he/she does not have adequate financial
resources. The assistance would be released to the beneficiary through PIA in case
he creates infrastructure himself without availing bank loan. In case farmer will avail
loan in that case, project assistance shall be released to the bank so as to adjust the
loan component of the bank. However, when poly-houses structures are constructed
and M.I. Systems are installed through empanelled companies. In that case, payments
can be released by DNOs directly after obtaining necessary completion and
satisfactory reports from PIAs and farmers. For that authorization to release payment
to companies be obtained from the farmers. The department or the approved firm as
the case may be shall assist the farmers in the preparation of projects to avail credit
facility from the banks. In case, farmer desire to get the infrastructure constructed
from approved empanelled company in that case, farmer will have to sign an
agreement with company. The prescribed agreement form is enclosed as per
Annexure VI.
• The document containing specifications of construction material to be used in the poly
houses and MI system is being provided separately (As per Annexure-IV).
5. Role and Responsibility of Project Implementing Agency: Subject Matter Specialist working in the Development Blocks will be the PIA’s.
They will be assisted by a core team comprising of ADO, JE, AEO (Graduate/Post graduate). He
and his core team shall be responsible for the following:
1. After receipt of the application on prescribed form from the beneficiary, the same
shall be entered in a register and a Sr. No. and date of receipt shall be assigned to
that application.
2. He and his team will visit the site to verify the feasibility within 10 days from the
receipt of application and will finalize the site and model of poly house on merit based
on parameters like aspect, direction and orientation etc. In case, some site
development is required, then the farmers will be guided accordingly and he farmer is
required to provide well leveled field/site for the construction of poly house to the
empanelled company at the time of signing of agreement.
3. Will recommend/reject the application after inspection of site. In case the site is found
suitable, the PIA will record details as per Annexure-II columns and will forward the
same to the project sanctioning authority for administrative approval alongwith
estimate of poly houses structure, micro-irrigation and water sources etc. as the case
may be within 5 days after inspection. To obtain Administrative/financial sanctions,
the indicative estimates provided separately can also be considered for which
estimates have already been provided..
4. Will exercised 100% test check during different phases of the execution of the project
components. However, it is mandatory for PIA and his core team to undertake the
following:
- Verification of developed site before signing the agreement or initiation of
construction work after the receipt of sanction from DNO.
- To witness the signing of agreement between farmers and company.
- Verification and certification of construction material dumped at the site for
construction of poly house and installation of MI system.
- Preparation of estimate of water source with photograph.
- Test check before putting up foundation of poly house structure ( recording of
measurements)
- Test check with in 3 days after the complete construction of poly house and related
infra-structure.
- Submission of all bill vouchers within 5 days after completion of construction work to
the DNO.
5. Identification of rural artisan/masons/farmers for training in green house construction and
green house technology in University/institutions.
6. In case, the poly house and related infrastructure is to be constructed by the farmer
himself by following the specification given by the Department, in that case,
facilitation for preparing estimate shall be provided by the Department through its soil
conservation/engineering staff.
7. If the farmers want to avail credit, necessary facilitation shall be provided by the PIA
for formulation of project.
8. PIA will ensure that farmer willing to avail assistance under the project must get
training in the selected institution before or during construction period of poly house.
9. He and his team will be responsible for quality control of construction, use of
specified construction material and for timely construction of structure to ensure
timely utility by the beneficiary. In case of any delay at farmer or company level, he
will report the same to the DNO.
10. Shall be responsible for preparation and submission of claims of project assistance
alongwith photograph of poly house with farmers, bankers as the case may be to the
project sanctioning authority i.e. DNO. The project assistance be recommended on
approved cost or only on actual cost basis, whichever is less.
11. Will guide and educate farmers about proper utilization of poly houses i.e. package of
recommendations on selection of crop, production and protection, fertigation, grading,
packaging etc.
12. Will submit project completion reports on the prescribed format to the District Nodal
Officer timely after inspection or joint inspection in case of bank loan where bank
loan was availed.
13. Submission of progress reports and reimbursement claims to the District Nodal
Officer every month on prescribed format.
14. Facilitation for signing of the agreement as per Annexure-VI between the farmer and
service provider (form/company) for construction of green house and installation of
MI systems inside poly houses. He alongwith one local person will sign the
agreement as witnesses.
15. Shall issue work order to the beneficiary to start work within 7 days after the receipt
of administrative approval from DNO, for the project components to be executed by
the Department i.e. 6sq.m poly tunnels and poly houses to be constructed by the
farmers by using local material (Bamboo ).
16. Will ensure that farmer must hand over a bank draft of required amount ( 20% )as
beneficiary share to the company at the time of signing of agreement with that
company.
17. PIA will have to maintain beneficiary-wise record as per Performa” A”.
5. Role and Responsibility of District Nodal Officer:
For smooth and effective implementation of project, Deputy Director of 10 Districts
and District Agriculture Officer of Lauahl & Spiti and Kinnaur and APO, Kaza will be Nodal
Officers for the Districts. DDA’s will be assisted by a core team comprising of District
Agriculture Officer, Sub Divisional Soil Conservation Officer and ADO Headquarter in 10
Districts. In Tribal areas the team would be DAO/APO, ADO, J.E.
1. The core team will delineate areas in district having production problem due to frost,
hail, high rainfall and long and severe winters so as to give priority to the farmers of
these areas for availing project assistance, so that they can start growing cash crops
under protective cover.
2. The DNO’s will convene a one day meeting-cum-workshop involving all the
stakeholders i.e. PIA’s and his core team, district level and sub division level officers,
DE of the Zone, FAC members. KVK Scientists etc.. During workshop, a
presentation be made on operational guidelines, physical and financial targets fixed
for the district for 2010-2011. Targets be fixed block-wise on the basis of
information generated by the core team of district as per item No.1 and targets be
fixed for the blocks component wise. Role and responsibilities of each member of
core team at district and block be discussed and outlined. The proceedings of
workshop/meeting are sent to the Directorate immediately. Training calendar of
officials/farmers/masons be prepared in consultation with KVK Scientists. A
monitoring team involving DE and KVK Scientists be formed. A team to oversee and
coordinate production of vegetables by the poly house farmers be constituted.
3. Will organize awareness campaign at focal points and educate farmers about the
project details. During the awareness campaigns, the willing farmers be provided the
prescribed application forms and necessary guidance as to how they can avail project
assistance.
4. District level core team and block level core teams shall also get training in
University/KVK as per calendar and module of training course to be finalized by the
SAU. Besides, training shall also be arranged in University for rural artisans/masons.
5. (a) D.N.O. shall issue administrative approval after scrutiny of the cases within 10
days from the date of receipt of cases from PIA’s with a copy to the concerned bank,
in case of Bank Loan.
(b) The DNO shall issue authorization letter in favour of the beneficiary for the
construction of poly houses/installation of micro irrigation systems/creation of water
source as per recommendations of PIA on the prescribed authorization letter given at
Annexure-II (a). This format shall be applicable, when agreement for development
of infra-structure is to be signed by the farmer with service provider. The works to be
executed departmentally (6 sqm) and water resource development, the sanction is to
be issued in favour of PIA.
6. DNO shall sanction the projects and project assistance as per the final assessment and
recommendation received from the PIA within 20 days from receipt of such request.
Completion period of each sub-project should not be more than 90 days from the date
of signing of agreement between the farmer and the empanelled company. However,
date of Administrative Approval shall be reckoned as the date for counting of period
of completion of sub-project being executed by the farmers themselves or
departmentally. In case, companies fail to complete the construction/ installation work
within the stipulated time period in that case DNO will initiate action against the
company by getting the beneficiary share refunded with 20% interest from the date of
signing of agreement. In case company does not repay the deposited amount with
interest then the same shall be recovered from the bank guarantee given by the
company. Also, in case farmer do not complete the work within stipulated period in
self cases, then sanction accorded is liable to be cancelled.
7. DNO will send copies of sanction letters to the executing company (service provider)
and to the Bank in case of loanee farmers.
8. DNO and his core team will exercise at least 25% test check.
9. DNO will release project assistance through PIA in the shape of cheque /bank draft
for non loanee farmers, whereas, in case of loanee farmers, the project assistance shall
be released through the concerned bank under intimation to PIA. The project
assistance can also be released to the company directly, but after obtaining consent
and satisfaction report from PIA/ farmers. However, DNO will ensure that the
payments should be released within 10 days of the receipt of bills from the PIA.
10. After the completion of sub projects, D.N.O. will submit the PCR’s to the Directorate
within 15 days for further submission to the NABARD.
11. DNO will prepare and submit model wise and size-wise reimbursement claims also.
12. DNO will maintain beneficiary –wise record on Performa “A” and will put the same
on departmental web site.
7. Generals:
Pragmatic and participatory approach with complete transparency would determine the
success of the project. Facilitation with regard to technical know how on all aspects of poly house
technology would be provided to the farmers so that they can utilize project assistance for
creation of infrastructure for protected cultivation of high value cash crops and increased quality
production for enhanced farm increase. This will provide self employment opportunities to the
rural youths in their farms.
7(a) Project Assistance:-
Rates per sq. meter and unit cost has been approved for different models of poly houses.
Similarly unit cost of micro irrigation systems to be installed in the covered area has also been
worked out. 80% project assistance is available to the beneficiaries for the construction of poly
houses and installation of micro irrigation in covered area under this project. Cost per sq. meter
of different models of poly houses and micro- irrigation systems are given at Annexure-IV. The
remaining cost shall be borne by the farmers through his own sources or by bank credit. The
project assistance shall be released after completion of the project/sub-projects. Farmers can also
avail credit for initial investment which shall be adjusted after receipt of project assistance from
the Department. Also, project assistance to the extent of 50% of the approved cost or actual cost
whichever is less is available for the creation and augmentation of water sources. Component-
wise maximum project assistance which individual farmer can avail is given below:
For Poly houses:
Ø For Bamboo poly houses project assistance @ 90% of cost is available to BPL farming
families. One farmer can avail assistance for one structure having 135 sq.m. covered area
and maximum four such structures. Project assistance up 60 sq. m. covered area can be
availed by one farmer in case of poly tunnel of 6 sq.m. (Model A-3) for nursery raising.
In case of low tunnels of 120 sq.m. and 192 sq.m. covered area assistance for only one
tunnel of suitable model as per site is allowed. These tunnels are suitable for raising
vegetable nurseries on commercial scale.
Ø One farmer can avail maximum assistance up to 1000 sq.m. covered area in case he
prefers poly house of 40 sq.m. (Model B1 to B4) and also other models (Edke Type
models A standard 20,40,60,80,100,120,134 and 140 Sq.m.). He can also avail assistance
in combination with other G.I. models but assistance would be allowed only for total of
1000 sq.m. covered area.
Ø For model 3C (C1 to C8), wherein covered are is 40 sq.m. and 100 sq.m., one farmer can
avail assistance for total covered area up to 1000/1008 sq.m. Area up to 1000 sq.m. can be
with 40 sq.m. and 100 sq.m. poly houses and in combination with other models but the
total covered area will remain 1000 /1008/1014 sq.m.
Ø For models (C9 to C12) (D1 to D4), D-AL (DAL1 to DAL 4), the covered area is 250
sq.m. One farmer can avail assistance for total covered area of 1000/1008/1014 sq.m.
(4X250 sq.m.) or in combination with other models.
Ø For other models of C & D specifications with covered area of 504 sq.m. and 1008 sq.m.,
the assistance would be allowed only for upto 1008 sq.m. covered area.
Ø For snow bound areas model Z (Z1 and Z2) are recommended. The maximum covered
area is 40 sq.m. One farmer can avail assistance for 400 sq.m. covered area (10X40 sq.m.)
However, C1 to C4 and AC-1 to AC-4 can also be allowed as replacement of Z model as
per choice of the farmers. But the assistance would be allowed for maximum of 400 sq.m.
covered area.
Ø Farmers are at liberty to choose any combination of models provided in the project, but
the assistance would be available for maximum 1008 sq.m. covered area. Project
assistance for approved models having covered area more or less than the area mentioned
above would be provided as the size of structure would depend upon location/site. Where
poly-house has not been constructed with standard length and width due to peculiar field
/site conditions, the approved per sqm rate of that particular model (Technology ) will be
considered for evaluation. For models up to 250 Sqm., the provision of double door will
be optional for which the cost of double door shall be borne by the farmers and shall not
be part of project assistance. However, in case of poly houses having covered area of
500/504/544 Sq. m. and covered areas of 1000/1008 Sq. m. , the provision of double
doors will be part of the total covered area and that area shall be considered for project
assistance along with covered area of main structure. The area eligible for assistance on
account of Annexe Door shall not be more than 6 Sq.m. in all the cases. Thus covered
area eligible for assistance would be 506/510/550/1006 and 1014 Sq.m. for different
models of 500/504/544/1000/1008 Sq. m. respectively. In all the cases, inside
measurements of constructed poly –house will be measured for calculation of covered
area.
Ø In case there is variation to the extent of 10 % or less in actual covered area as compared
to the original sanction, then there is no need to revise the sanction. However, the farmer
will be paid for total covered area. In case due to site specific situation, the variation is
more than 10% , then revised sanction is required to be issues.
For Micro Irrigation:
Unit cost for different covered areas under sprinklers and drip with fogger systems
has been approved and the same is enclosed as per Annexure-III. The project assistance @
80% of unit cost is available to the farmers.
For Water shortage and Augmentation of Water Source:
Farmers can avail assistance for one storage structure as per suitability and
requirement. However, it is expected that water source would be available with majority of
the farmers therefore, the number of such structure is not at par with the poly house
structures. As per estimates prepared on the basis of analyzed rates, the maximum limit of
assistance has been worked out and the same is given below:
Ø 50 % assistance with maximum limit of Rs. 22,000/- per tank with poly lining and brick
lining having 50 cum. capacity.
Ø 50 % assistance with maximum limit of Rs. 21,000/- for stone masonry tank of 9 cum.
Capacity.
Ø 50 % assistance with maximum limit of Rs. 42,500/- for RCC tanks of 20 cum. Capacity.
Ø 50 % assistance with maximum limit of Rs. 70,000/- for RCC tanks of 50 cum. Capacity.
Ø 50% assistance for shallow wells of appropriate depth and diameter (minimum depth 8
mtrs and diameter 2 mtrs.) with maximum limit of Rs.55,000/-.
Ø 50% assistance for shallow bore well and deep bore wells with minimum depth 35 mtrs.
and 70 mtrs. with minimum dia 125 mm and 200 mm. respectively. Maximum limit of
assistance for shallow bore well and deep bore well would be Rs.1.0 lac and 2.5 lac.
respectively. The depth of bore wells can be more than 35 meters and 70 meters but the
project assistance would remain the same. Both M.S. Pipe and P.V.C. Pipes for bore well
assembly can be used. Indicative estimates of all possible drilling methods have been
prepared and already provided while evaluating these structures; expenditure on SOP and
Pump House can also be considered. The expenditure on pumping machinery can also be
included hence forth as provision of pumping machinery in the project document is less.
Demand for construction of bore wells is more, therefore in view of more demand
assistance for bore wells will only be allowed on community basis, i.e. for more than two
farmers and not to individual farmer. Minimum command area under one bore well would
be 1000 sqm covered area and the created water potential should also be used for
providing irrigation in the open fields also i.e. both the projects (Part –I & II) can be
dovetailed. In future ,no bore well will be sanctioned where covered area under poly-
houses is less than 1000 sq.m..
Ø 50% assistance is available for lifting water with electric motor of 3 HP and 7.5 HP i.e.
low and medium lift with maximum assistance upto Rs.50,000 and Rs.1,50,000
respectively. Low lift will be considered up to 3 H.P and medium lift will be considered
above 3 HP. Where pumping machinery of more than 7.5H.P. is required, the same is also
allowed but subject to maximum level of assistance which would remain Rs. 1,50,000/-.
For lifts electric operated pumping machinery as well as Diesel operated pumping
machinery is allowed. This will also be available for group of farmers.
Ø 50% assistance is available for pumping machinery of 1.0 HP with maximum limit of
Rs.3133/-
8. Monitoring and Evaluation:
Concurrent and post project monitoring and evaluation of project is very
important. This would help in bringing about need based modifications in the operational
modalities of the project and would provide guidance with regard to facilitation required for the
success of the project both to the beneficiaries and implementing department. It would be done
by the;
- State level committee constituted for the smooth implementation of the project.
- By the funding agency i.e. NABARD.
- State level project implementation unit, D.N.O. and PIA.
- By an independent agency having sufficient experience and knowledge of the subject,
if need arises.
9. Facilitation to the Farmers:
- Poly house models suitable for different agro-climate conditions have been prepared
and would be provided to them..
- Complete designs of different models with specifications have been prepared and
shall be made available to them to decide appropriate models they would like to
construct.
- Specifications of construction material for the longevity and sustainability of
structures have been approved and accordingly cost of construction has been worked
out.
- For the installation of micro-irrigation systems, specifications of different components
have been prepared and shall be provided.
- To determine amount of assistance for different components of the project, estimates
of different components have been approved and firms/companies eligible to act as
service providers have been empanelled as per list attached at Annexure-V.
- For sensitization, capacity building of extension officers/ farmers, about green house
technology, State Agriculture University, Krishi Vigyan Kendra, NGO’s etc. would
be involved.
- Site specific Cost estimates of all the components of the project shall be prepared by
the experts of the department, if the project is to be executed by the farmers himself
without the help of service providers empanelled for the purpose.
- For obtaining bank loan, facilitation shall by provided by the Department for
preparation of cases.
- For the construction of green houses with local material, local artisans will be
imparted need based training in the Agriculture University through the D.N.O.
- Research and development support shall be provided by the Universities during the
project implementation and post project period.
- Farmers shall be provided prescribed form to enter into agreement with eligible
firm/company for the construction of poly houses and execution of micro irrigation
system.
10. Expected Outcome:
- 4 to 10 times higher productivity of cash crops especially vegetables.
- Gainful employment to 6,000 families/ educated youths.
- Capacity building and employment to more than 1,000 local artisans.
- Higher income and change in socio-economic status of small and marginal farmers.
- Projection against unfavorable weather and climatic factors.
- Saving of monitory inputs through adoption of precision farming techniques.
- Protection of environment due to lesser use of hazardous chemicals.
Note: These guidelines are subject to modifications as per felt needs.
Annexure-A Performa for maintaining beneficiary wise record under Pt. Deen Dayal Kisan Bagwan Samridhi Yojna Part –I & Part -II (A separate page in register is to be allocated for each farmer/ beneficiary on financial year basis)
Sr. No.
Particulars of Farmer/ Beneficiary
1. Name of the farmer with complete address and telephone number.
2. Date of Receipt of Application
3. Date of field verification
4. Date of A.A.
5. Date of issue of authorization letter
6. Date of Receipt of Bills
7. Date of Disbursement
8. Date of submission of P.C.R.
9. Area under Project Proposal
1. Poly house model with area coverage
M.I. Systems Area Cost Assistance 80% Under system
a) i) Type of M.I. System and Area under covered conditions.
ii) Name of the Company executing the component.
b) i) Type of M.I. System and Area under opened conditions.
ii) Name of the Company executing the component.
2. Water Source Augmentation i) Type of Tank, size and capacity. Cost
Assistance 50% ii) Shallow Bore well /shallow
well/Deep Tube well / small and medium lift (Discharge ) ( (Specify on individual basis or
cluster basis)
Cost Assistance 50%
3. Pumping units specify (HP, Head , Discharge )
Cost Assistance 50%
10. Total cost of the scheme components
11. Total assistance to the beneficiary (I + ii+ iii)
12. Any other detail
Ikfjf’k"V&d
lsok esa
mi d`f"k funs’kd @ ftyk d`f"k vf/kdkjh@
lgk;d ifj;kstuk vf/kdkjh]-----------------------------
-------------------------------ftyk---------------------fg0 iz0 A
fo"k; % iafMr nhu n;ky fdlku ckxoku le`f) ;kstuk ds
vUrZxr lgk;rk gsrq izkFkZuk i= A
Jheku th]
eSa----------------------------------------------------------------------liq=@liq=h@iRuh Jh---------------------
------------------------------------------------------------xkao--------------------------------------------------------------------Mkd?kj------------------
--------------------------------------------------------------------------------------rglhy-----------------------------------------------ftyk----------
-------------------------------------------------------------------------fgekpy izzns’k dk LFkkbZ fuoklh gwWa A esjh fdlku ikl
cqd ds vuqlkj--------------------------------------------eydh;r Hkweh gS ftlesa ls --------------------------Hkwfe Qly dks
mxkus ds fy, mi;qDr gS A eSa mijksDr ;kstuk ds vUrZxr miyC/k forh; lgk;rk }kjk ikWyh gkÅl
¿gfjr x`gÀ ;kstuk dk fuekZ.k djuk pkgrk gwWa A flapkbZ gsrq esjs ikl lk/ku miyC/k gS@ugha gS A
vr% eSa blds fy, Hkh vko’;d lgk;rk pkgrk gwWa@ugha pkgrk gwWa A eSa vius ifjokj ,ao lEcfU/kr
fooj.k fuEu izdkj ls ns jgk gwWa A
1- iwjk irk
nwjHkk"k u0
2- ifjokj ds dqy lnL; uke vk;q ’kS{kf.kd ;ksX;rk
iq:"k
fL=;ka
cPps
3- D;k izkFkhZ vuqlwfpr tkfr@ vuqlwfpr
tutkfr ls lEcU/k j[krk gS gka@ ugha
4- ifjokj ds lnL; tks ljdkjh ,ao xSj
ljdkjh ukSdjh dj jgs gSa A
5 D;k izkFkhZ xjhch js[kk ds uhps ¿ ch-ih-
,yÀls lEcU/k j[krk gS gka@ ugha
6- dqy Hkwfe ¿fdlku ikl cqd ds vuqlkj À
dÀ flafpr {ks=
[kÀ vflafpr {ks=
7- ikuh dk L=ksr
8- [ksr@[ksrksa dk dqy {ks=Qy tgka
ikWyhgkÅl dk fuekZ.k fd;k tk,xk
¿[kljk u0 lfgrÀ
9- i'kq/ku
1-
2-
3-
4-
10- Qlyksa dk mxkus esa eq[; leL;k,sa A
1- vksykof̀"V
1- vf/kd o"kkZ
2- dksgjk
3- cQZ fxjus ds dkj.k
5-vU; ¿iFkjhyh] ikuh [kMk gksus dh leL;k bR;kfnÀ
11- ;kstuk ds vUrZxr forh; lgk;rk fuEu 1] 2] 3] enksa ds
ckjs esa gka@uka Li"V djsa A
1-ikWyh gkÅl fuekZ.k gsrq
¿dÀ D;k Loa; djokuk pkgrs gSa] gka@ugha A
¿[kÀ ;fn ugh arks dEiuh dk uke o irk A
2- lw{ke flapkbZ lqfo/kk gsrq
¿dÀ fLizadyj
¿[kÀ Vid
¿xÀ dEiuh dk uke o irk A
3- VSad] dqavk] cksj oSy] iEi ;wfuV ds fuekZ.k vFkok ty
mBkÅ ;kstuk ds fy, A
12- cSad ls _.k ysuk pkgrk gwWa ;k ugha A ;fn gka rks cSad dk
uke] iwjk irk
Åij nh xbZ lwpuk iw.kZ :i ls Bhd gS rFkk eSa ;kstuk esa fn, x, fn’kk funsZ’k
ds vuqlkj dk;Z djus ds fy, rS;kj gwWa A vr% eSa vkils vuqjks/k djrk gwWa fd eq>s dzekad 11 ds
vUrZxr n’kkZ;s x, enksa gsrw foRrh; lgk;rk dh Lohdf̀r iznku dh tk;s A eSausa dEiuh@dEifu;ksa dk
pquko dzekd 11 ds vUrxZr enksa ds fuekZ.k gsrq Loa; fd;k gS] ftldh lwfp foHkkx us iznku dh gS
A eSaus foHkkx ls fofHkUu lkefxz;ksa dh LiSlhfQds’ku dk fooj.k tks ikSyh gkÅl fuekZ.k ds mi;ksx
esa yk;h tk;saxh Hkh izkIr dj fy;k gS vkSj foHkkfx; MhtkbZu rFkk LiSlhfQds’ku ds vuqlkj gh ;k
rks Loa; ;k foHkkx }kjk lwfp o) dEifu;ksa }kjk dke d:axk@djokÅaxk A
Hkonh;
fdlku ds gLrk{kj---------------------------
iwjk irk--------------------------------------------
VsyhQksu@eksckbZy u0----------------- Annexure-II
Format to be filled in by the PIA for submission to District Nodal Officer for obtaining Administrative Approval of the project proposal.
1. Date of receipt of Application
2. Date of spot inspection
3. Category of farmers (SF/MF/Other from SC/ST/Gen./BPL)
4. Feasibility report.
Poly Houses A. a) Khasra No. and Size of field where
farmers intend to construct poly houses
b) Size of Poly-house
c) Executing Agency
Ø Self
Ø Firm/Company with Name & Contact No.
e) Estimated Cost (as per A above)
f) Amount of assistance.
g) Amount of Beneficiary Share
B. Micro-Irrigation System
(a)Sprinkler (b)Drip & Fogger Name & contact No of firm
(i)Executing Agency
(ii) Area to be covered in (Sq.m).
Estimated cost of covered area, with system to be installed as per B(a&b)
(i)Amount of Project Assistance (ii) Amount of Beneficiary Share
5. (A) Feasibility & requirement of water potential as per specifications given in project document/operational guidelines. (i)Water storage structure (specify capacity in cum or liter/sec.)
Ø Poly & Brick Lined Ø Stone Masonry Ø R.C.C.
(ii) Shallow Well
(iii) Bore Well Lifts (small or medium) (Total Head, Discharge & H.P. of Pumping System)
5.(B). Estimate of the sources to be created as per 5A (i)Amount of assistance.
5.(C). Requirement of pumping unit in case of shallow and Bore wells (specify purpose & type of pumping unit) (i)Cost (ii) Amount of assistance
6. Recommendation of PIA to DNO for Administrative Approval. Total estimated cost of Poly-House
structure /Micro-irrigation.
a) Eligible cost (i) Project share (ii) Beneficiary share 7 (A) Mode of payment of project assistance
Ø Directly to the beneficiary ( as per guidelines)
Ø Through bank ( to be specified ) in case Beneficiary willing to avail credit facility (Full Name & Address of Bank)
7(B) Beneficiary would contribute his share as per procedure given in the guidelines.
1. Certified that above details are based on spot inspection and information furnished by the
beneficiary. 2. Certified that the undertaking from beneficiary shall be obtained on affidavit as per
guidelines Annexure-II (b) after the issue of administrative approval and before the issue of work order/ after the issuance of authorization based on above from Sr. No. 1 to 7.
Submitted to the DDA- Cum- District Nodal Officer for favour of perusal
and further necessary action along with necessary estimates and documents.
SMS cum PIA , Dev. Block____________ Distt.________
Annexure:_II(a) To Shri___________________________ S/O Shri________________________ Resident of village________________
P.O.___________Tehsil____________ Distt.___________________H.P. Subject : Authorization for construction of Poly-House/ installation of Micro
Irrigation system/creation of water source. Sir, Please refer to your application dated_______________________________and recommendations of PIA received vide letter No._________________________ dated_______________. You are hereby authorized to undertake the followings as per specifications given in the guidelines issued by the Govt. vide letter No._____________________________ dated_________________.
1. Construction of Poly –house Model (___________________________) having covered
area (______________Sq.M.)with an estimated cost of Rs.
____________________(Rupees__________________________________________)
only through Company /Service Provider M/S
_______________________________________________________empanelled for this
purpose vide letter No. ________________________________________Dated;_______.
2. Construction of Micro-Irrigation System inside covered area
(_______________________Sq.m.) with an estimated cost of
Rs._____________________
(Rupees______________________________________________________) only through
company/service provider M/S
_____________________________________________________ empanelled for this
purpose vide letter No._________________________dated_____________
3. For the construction of Tank/Well/Bore well/lift (capacity)/ pumping unit having
capacity______
__________________________cu.m /LPS with an estimated cost of
Rs._____________________
(Rupees____________________________________________) only as per estimated
cost prepared and submitted by PIA after spot inspection.
The above authorization is subject to the following terms and conditions:
1. Eligibility of assistance for (1) and (2) components would be 80% and for component it would be 50% subject to actual evaluation and measurement done by the PIA or his authorized representative.
2. For any deviation from the given/ approved specifications with regard to constructions material and design etc. you will be liable for the same and the same may lead to forfeiture of assistance available under the scheme .
3. 10% variation in the sanctioned covered area is allowed depending upon the site for which revised sanction is not required. In case, likely deviation is more than 10%, then revised sanction be obtained before starting the construction work.
4. Before undertaking constructions work, you have to submit an affidavit on the prescribed form at Annexure II b
5. Before assigning work to the company/service provider, you will sign an agreement with the company/service provider and will comply with the agreed terms and conditions especially with regard to remittance of payments on the prescribed form annexed in the guidelines . (At annexure -VI).
6. You will have to provide well levelled field /site for construction of Poly House and related infra-structure.
7. You will have to carry the material at your own cost from motorable pucca/ katchha road head to the actual site.
8. Facilitation of stay arrangements for the staff/workers of the company is required to be provided.
9. You will have to deposit 20% of the total cost of construction with the Company in the shape of bank draft at the time of signing of agreement.
10. You will have to make arrangement for electricity and water at the site. 11. You will have to make payments to the companies for optional and additional items, if
desired by you.
District Nodal Officer cum Deputy Director of Agriculture, Distt.________________.H.P
Copy forwarded to:
1. The PIA cum SMS Development Block _________Distt._____H.P.
2. The Manager,___________________________________Branch_________________
P.O.___________________Tehsil____________________Distt.____________________
H.P.
3. The Company /Service Provider selected by the farmer to execute project component /
components.
4. District Lead Bank Manager____________________Distt.___________.H.P. for
information and necessary action at his end please.
District Nodal Officer cum
Deputy Director of Agriculture,
Distt.________________.H.P.
Annexure –II(b)
Undertaking to be given by the beneficiary in the shape of affidavit to be attested by
the 1st class Magistrate/ Notary (After receiving the sanction from DNO.)
I/We_______________________________________________________
S/O_______________________________________________R/O__________________
_______
hereby undertake the following.
1. That I have received approval for the Construction of Poly –House (--------Sq. m. ),
Micro-Irrigation system (___________________Sq. m.) and for the creation of water
source i.e. tank/bore well/well/lift/pumping unit and I am eligible to receive project
Assistance amounting to Rs._______________________after the creation of
infrastructure mentioned above.
2. That I will sign agreement with service provider within 15 days from the receipt of
authorization and in case the construction is to be done by me then will complete the
construction within 90 days,
3. That I will utilize and maintain the infrastructure created through project assistance
for a period of minimum five years.
4. That I will use the Poly –house for raising vegetables mainly.
5. That I have not availed any assistance for the creation of same infrastructure as
approved as per Sr. No. 1 above.
6. That the contents of my application submitted to the Agriculture Department for
sanction of project assistance under Pandit Deen Dayal Kisan Bagwan Samridhi
Yojna- Part -I are correct and no part of it is wrong and nothing has been concealed
there from.
7. That I will part with my share (20%) for the installation of infrastructure (Poly –
House or Micro irrigation or both) at the time of signing of agreement against
sanctioned amount of these components which have been approved vide letter
No.__________________________________dated
__________________________by the Distt. Nodal Officer (Dy. Director of
Agriculture /Distt. Agriculture Officer and Assistant Project Officer ) as per terms
and conditions laid down for the operationalization of the scheme.
8. That I will provide well leveled field /site for the construction of this infra-structure
before signing of the agreement.
9. That I will bear the carriage charges of construction material from the pucca or
Katchha road head to the site.
10. That I will make arrangement for electricity and water etc .at the site.
11. That I will facilitate for making stay arrangements of the labour who will be involved
in the erection of these structures.
12. That I will bear the expenditure for extra fixtures and optional items.
I further undertake that in the event of departure from the above terms and
conditions from Sr. No. 1 to 12, I shall be liable to refund the whole or part of the project
assistance as the case be to the project sanctioning authority i.e. Distt. Nodal Officer,
Distt._______________________H.P.
Deponent
Verification.
I the above named deponent do hereby solemnly admit and verify that the
contents of the above affidavit are true and correct and no part of it is false and nothing material
has been concealed there from.
Verified at__________________on this ____________________day
of_______________2009.
Deponent
Note: To be attested by 1st class Magistrate / Notary.
Annexure-III
Specifications for Installation of Micro-Irrigation Systems under Protected Cover Area ,Approved Rates per Sq.m.Covered Area and Unit Costs
Sr. No.
Micro-Irrigation
System (Model -
Wise)
Description Covered Area For
Unit
Approved Rate per Sqm Covered Area (Rs.)
Approved Cost per Unit Rs.
1 2 3 4 5 A) SPECIFICATIONS FOR
SPRINKLERS:-Indicative requirements of sprinkler components will include (PVC/ HDPE pipe 32mm,40mm ,50mm,63mm of suitable pressure ratings), (Double effect 1" air release valve), (Lateral 16mm LLDPE),( Control valve (Ball) 32mm, 40mm, 50mm, 63mm ), ( 1"Disc filter 130micron (3 -7 m3 / hr. ), (1,1/4" 130 micron 12 m3/ hr 1,1/2" 130 micron 12m3 / hr.), ( 25 m3 /hr.Media sand filter with back flush assembly 10m3/ hr. ), ( Micro sprinkler with up side down configuration with anti drain at spacing of 4 x 4 meters with discharge of 105lph at 25-30 meter head)( 2.50 Kg / Cm 2 to 3.00 Kg /Cm 2),
1 (40sqm) Sprinkler System for 40 Sqm covered area. 40 103.00 4120.00 2 (100Sqm ) Sprinkler System for 100 Sqm covered area. 100 61.50 6150.00 3 ( 250 Sqm) Sprinkler System for 250 Sqm covered area. 250 33.50 8375.00 4 (2x
250Sqm) Sprinkler system for 2X250 Sqm covered area. 500 22.00 11000.00
5 (500Sqm) Sprinkler System for 500 Sqm covered area. 500 22.00 11000.00 6 (1000Sqm) Sprinkler System for1000 Sqm covered area. 1000 19.50 19500.00
B) SPECIFICATIONS FOR DRIP + FOGGERS :-Indicative requirement of drip + fogger system components will consist of PVC/ HDPE pipes of suitable dia & pressure rating, Air release valve 1”, Laterals 16mm LLDPE, Drip lines Integral or inbuilt 16mm x 20/30cm , 1.30LPH / 2 to 2.40 LPH(Class-II)depending upon soil texture (light, medium and heavey soils), 0.9mm thick, PP flow control valve 16mm, PP control valve (Ball) of suitable size, Disc filters 130 micron , Media /Sand filter with back flush assembly 103/hr, By pass assembly 1” x 1”, 2"x 1.5" or 1.5" x1.5" , Ventury ¾ " with flow meter and flow regulator, Fogger (with cross and anti drains valve at spacing of 3.00 x 3.00 meter with discharge of 28 LPH at 35m ), pressure gauge (Glycerin filled), misc. fittings and accessories etc.
1 (40sqm) Drip fogger system for 40 Sqm covered area. 40 240.00 9600.00
2 (100Sqm ) Drip fogger system for 100 Sqm. Covered area. 100 144.00 14400.00
3 ( 250 Sqm) Drip fogger system for 250 Sqm. covered area. 250 99.00 24750.00
4 (2x 250Sqm)
Drip fogger system for 2X250 Sqm covered area. 500 89.00 44500.00 5 (500Sqm) Drip fogger system for 500 Sqm covered area. 500 95.00 47500.00 6 (1000Sqm) Drip fogger system for 1000 Sqm covered area. 1000 80.00 80000.00
Note:- 1) The farmer will provide required quantity of qulity water in a storage structure at one corner of the Poly -House at a reasonable distance of 10 to 20 meters.The assistance of 50% is available for water storage structure and augmentation of water source up to a limited no. as in number of cases,the use of such type of existing structure will be ensured.
2)The farmer will also provide suitable pumping units of required capacity for which water source development and augmentation is available.Assistance for small pumping units up to limited number is also available up to 50% with a maximum ceiling of Rs. 3133/- only.
Annexure-IV
Specifications of Poly-House Structures and Model -wise Approved per Sqm Covered area and Unit Costs.
Sr. No.
Model Model -wise Description of Specifications of Construction material and Dimensions of Poly Houses
Unit Size in
Sqm.
Approved Rate Per
Sq m Covered
Area
Approved Cost
per Unit
1 A - (III) (6 Sqm)
C/o Very Low Cost tunnel Poly House with G.I. Pipe (A-Class ) frame 15mm diameter confirming to IS. Code 1239 and zinc coating as per IS Code 4736. Frame structure as per approved standard Drawing & design (Annexure -A &B)
6 Sqm
525 (Shall be executed department
aly) 3150
Specifications and Dimensions: Length 4.00 mtr. ( Spans at 1.00m each ), Breadth 1.50 mtr. Center height 1.00 mtr. (Semi circular). Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e.G.I. profile etc. or with aluminium strip fixed with G.I. nuts and bolts.
1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life ( Two years ), the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200micron . The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
2 C (40 Sqm)
Low Cost Modified Side ventilation Poly house (As per standard Design & Drawing)( Annexure -A & B ) Approved with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different diameters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia and 2 mm thick ( for horizontal & Arc), 25 mm dia and 2.65 mm thick (for Column) including earth work in foundation &C.C. 1:3:6 for encasing column pipe ,Processing, fabrication and erection with all fitting and accessories
Specifications and Dimensions Length : 10.00 mtr. ( Spans at 1.00m each ), Breadth : 4.00 mtr. Side /Center height : 2.00/4.00 mtr. (Semi circular type).
Sub Structure: Column: 25 mm dia G.I. Pipe. Top Arc with tie beam: 15mm G.I. Pipe King Posts, Struts & Ties:15mm G.I. Pipe
Door and End Frame: One door size 1mx2m made from 1.25″x1.25″M.S. square pipe (duly painted) with poly sheet . End frames fabricated of G.I.Pipes of respective dia as mentioned in the drawings. All parts of M.S. Square pipe should have red oxide priming coat followed by brush painting ( two coats ).
Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. G.I. Profile etc. 1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3)U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. It should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on two sides from top of side prop to 1.50m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried to minimum depth of 30 cm in the ground on the lower side to prevent migration of insects - Pest and seepage of water from outside etc.
Insect Nets: U.V proof insect net of 20 to 40 mesh is to be provided in the side walls, wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect . The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation & ii) All Round Ventilation. iii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers.Increased side / central height, Fan & Pad system. iv) Side height of ventilation can be increased. v) Height of fixed sheet from ground level can be decreased up to 0.75 mtr. Farmers can get these optional features installed / created but, extra cost if any will be paid and met by the farmers.
C1& C2 a) Without Shade net with UV. Film having specifications mentioned under Sr. No.2( Item no. 1&2) 40
Sqm 1080.00 43200
-do- b) Without Shade net with UV. Film having specifications mentioned under Sr. No.2 (Item no 1,2& 3). 40
Sqm 1085.00 43400
C3& C4 c) With U.V. Shade net 50% shading effect exterior / interior fitted with UV film having specifications mentioned under Sr. No.2 ( Item no. 1&2).
40 Sqm 1100.00 44000
-do- d) With U.V. Shade net 50% shadin g effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 2(Item no 1,2& 3).
40 Sqm 1140.00 45600
3 AC (40 Sqm)
Low Cost Modified Side ventilation Poly house (As per standard Design & Drawing Approved (Annexure -A& B) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia and 2 mm thick for purlin, ridge, insect net and roll up system, 32mm dia 2.65 mm thick for vertical posts ( Column) and horizontal beam , 25 mm dia and 2.65 mm thick (for Arc and , wind tie , front and back support) including earth work in foundation &C.C. 1:3:6 for encasing column pipe ,Processing, fabrication and erection with all fitting and accessories
Specifications and Dimensions Length : 10.00 mtr. ( Spans at 2.00m each ), Breadth : 4.00 mtr. Side /Center height : 2.00/4.00 mtr. (Semi-circular type ).
Of Sub Structure: Stanchions/ props : 32mm G.I. Pipe Top Arc with tie beam: 25mm G.I. Pipe King Posts, Ridge , Purlin & Ties:15mm G.I. Pipe Of Door and End Frame: One door size 1mx2m made from 1.25″x1.25″M.S. square pipe (duly painted) with poly sheet . End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawing. All parts of M.S. Square Pipes should have red oxide priming coat followed by brush painting ( two coats )s. Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. G.I. Profile etc. 1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3)U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. It should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Side Ventilation :Side ventilation roll up system provided on two sides from top of side prop to 1.00m downward and is designed to open from bottom to top with manually operated mechanism. From ground level to 1.00m height is to be provided a strip of U.V. poly sheet in order to prevent drafts in and around the ground area. Sheet shall be buried to minimum depth of 30 cm. in the ground on the lower side to prevent insect - Pest migration and entry of water from outside. Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls, wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior shading is recommended which can be removed as and when required and Shade nets which provide 50% shading effect and nets should be U.V. stabilized. The shade nets can also be fixed in side poly houses for workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation & ii) All Round Ventilation. iii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers.Increased side / central height, Fan & Pad system. iv) Side height of ventilation can be increased. v) Height of fixed sheet from ground level can be decreased up to 0.75 mtr. For these options ,extra cost if any, is to be born by the farmers.
AC1& AC2
a) Without Shade net with UV. Film having specifications mentioned under Sr. No.3( Item no. 1&2) 40
Sqm 1080.00 43200 -do- b) Without Shade net with UV. Film having specifications
mentioned under Sr. No.3 (Item no 1,2& 3). 40 Sqm 1085.00 43400
AC3 & AC4
c) With U.V. Shade net 50% shading effect exterior / interior fitted with UV film having specifications mentioned under Sr. No.3 ( Item no. 1&2). 40
Sqm 1100.00 44000 -do- d) With U.V. Shade net 50% shading effect exterior / interior
fitted with UV. Film having specifications mentioned under Sr. No. 3(Item no 1,2& 3). 40
Sqm 1140.00 45600 4 C (105
Sqm) Low Cost Modified Side ventilation Poly house (As per standard Design & Drawing Approved ( Annexure -A& B) ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia and 2 mm thick ( for Roll up),20 mm dia and 2.35 thick (for Horizontal in front and back , Ridge, insect net, king post and Ties), 25 mm dia 2.65 mm thick (for Bracing & trusses and Extra support front and Back), 32 mm dia 2.65 thick (for Column) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including G.I. profile, Spring, Molding, Processing fabrication and erection with all fitting and accessories.
Specifications & Dimensions Length: 15.00 mtr. ( Spans at 2.50m each ), Breadth: 7.00 mtr. Side /Center height : 2.50/4.00 mtr. (Semi circular type ).
Of Sub Structure:
Stanchions/ props : 32mm G.I. Pipe Top Arc with tie beam, : 25mm G.I. Pipe King Post, Struts& Ties : 20mm G.I. Pipe Of Door and End Frame: One door size 1mx2m made from 1.25″x1.25″ M.S. square pipe duly painted with poly sheet . End frames fabricated of G.I. pipes of respective dia as mentioned in the drawing. Square duly painted first with red oxide priming coat and then brush painting ( two coats )on all M.S. parts.
Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. G.I. Profile etc. 1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company are liable to replace the same. 2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3)U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. It should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation : Side ventilation roll up system provided on two sides from top of side prop to 1.50m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried to minimum depth of 30 cm in the ground on the lower side to prevent migration of insect - Pest and seepage of water from outside etc. Insect Nets: U.V Stabilized insect net of 20 to 40 mesh as per agro- climatic conditions is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent of entry of insects inside the poly house. Shade Nets: Fixed type exterior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect . The shade nets can also be fixed in side poly houses for better and easy workability and as per choice of farmers, with manual folding aznd spreading facility. Optional:- i) Top Ventilation & ii) All Round Ventilation. iii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers.Increased side / central height, Fan & Pad system. iv) Side height of ventilation can be increased. v) Height of fixed sheet from ground level can be decreased up to 0.75 mtr. vi) Annex Door. For these options ,extra cost if any, is to be born by the farmers.
C5 & C6 a) Without Shade net with UV. Film having specifications mentioned under Sr. No. 4( Item no 1&2). 105
Sqm 880.00 92400 -do- b) Without Shade net with UV. Film having specifications
mentioned under Sr. No. 4 ( Item no 1,2& 3). 105 Sqm 890.00 93450
C7 & C8 c) With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No.4 (Item no 1&2). 105
Sqm 930.00 97650 -do- d) With U.V. Shade net 50% shading effect exterior / interior fitted
with UV. Film having specifications mentioned under Sr. No. 4 ( Item no 1,2& 3.) 105
Sqm 935.00 98175 5 C (250
Sqm) Medium Cost Medium Technology Side ventilation Poly house (As per approved standard Design & Drawing , Annexure -A & B) ) G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia 2 mm thick ( for Roll up),20mm dia and 2.35mm( for Strut & Ties, Purlin, Insect net and Front & Back), 25 mm dia ,2.65 mm thick (for Horizontal beam , Extra support in front and back ,Ridge &Hoop), 40 mm dia 2.90 mm thick (for Column & King Post) including earth work in foundation & C.C. 1:3:6 for encasing column pipes including Aluminium profile etc. Molding, Processing, fabrication and erection with all fittings and accessories
SpecificationS & Dimensions Length : 25.00 mtr. ( Spans at 2.50m each ), Breadth : 10.00 mtr. Side /Center height : 2.50/4.00 mtr. (Semi circular type ).
Of Sub Structure: Stanchions/ props : 40mm G.I. Pipe Top Arc with tie beam: 25mm G.I.Pipe Struts & Ties : 20mm G.I.Pipe Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made from 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricatedof G.I. Pipes of respective dia as mentioned in the drawings. All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex. Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. aluminium Profile only. 1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.. 3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation :Side ventilation roll up system provided on two sides from top of side prop to 1.50 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc. .
Insect Nets: U.V stabilized insect net of 20 to 40 mesh as per agro -climatic conditions is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house.
Shade Nets: Fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect . The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation & ii) All Round Ventilation. iii) Annex double door. iv) Side /Central height 2.50/4.50m v) Side /Central height 3.00/5.00m. vi) Fan & Pad system. vii) Arrangement for movable exterior/interior rolling type shading. viii) Side height of ventilation can be increased. ix) Height of fixed sheet from ground level can be decreased up to 0.75 mtr. as per choice of farmers and for these extra cost if any is to be born by the farmers.
C9& C10 a)Without Shade net with UV. Film having specifications mentioned under Sr. No. 5 ( Item no 1&2 ).
250 Sqm 755.00 188750
-do- b)Without Shade net with UV. Film having specifications mentioned under Sr. No. 5 (Item no 1,2& 3).
250 Sqm 760.00 190000
C11& C12
c)With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 5( Item no 1&2).
250 Sqm 780.00 195000
-do- d) With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 5( Item no 1,2 & 3).
250 Sqm 788.00 197000
6 C 504Sqm Chi-AL
Medium Cost Modified Side ventilation Poly house (As per Approved standard Design & Drawing , Annexure -A & B) ) G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia 2 mm thick ( for Roll up,), 25 mm dia ,2.65 mm thick (for Purlin, Strut & Ties), 40 mm dia 2.90 mm thick (for King Post, Horizontal Beam& Hoops), 50 mm dia 2.9 mm thick (for Vertical Post) including earth work in foundation & C.C. 1:3:6 for encasing column pipes including Aluminum profile etc. Molding, Processing, fabrication and erection with all other fittings and accessories.
Specifications and Dimensions : Length: 24.00 mtr. ( Spans at 4.00 m each ), Breadth: 21.00 mtr. (Spans at 5.25 m each ), Side /Center height: 2.70/4.50 mtr. (Semi circular type). Gutter height 2.70 m, Ridge height 4.50 m. Of Sub Structure: Stanchions/ props : 50mm G.I. Pipe Top Arc with tie beam: 40mm G.I. Pipe Struts & Ties : 25mm G.I. Pipe Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings . . All part s of M.S. Square pipe should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex. Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc. Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter.
1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.. 3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Ventilation: All round Ventilation roll up system provided on four sides from top of side prop to 1.70 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc.. Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided with all side walls and top ventilation openings, wherever applicable as per opening space/vents and tightly fitted to be provided with natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation. ii)Side Gutters for Roof Top water harvesting. iii) Gutter height & Ridge height 3.00 m / 5.00 m.
iv) Fan pad system for cooling. v)Adjustment in side & top ventilation space. vi) Aluminum doors with U.V. films or carbonate sheets etc. vii) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
viii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers and for this extra cost if any is to be born by the farmers.
ix) Height of fixed sheet from ground level can be decreased up to 0.75 mtr.
CHi-AL1, CHi- AL2
Without Shade net with UV. Film having specifications mentioned under Sr. No.6 (Item no 1,2 & 3).
504 + 6 Sqm 735.00 374850
CHi- AL3, CHi- AL4
With U.V. Shade net 50% shading effect exterior/ interior fitted with UV. Film having specifications mentioned under Sr. No. 6 ( Item no 1, 2, &3). 504 +
6 Sqm 760.00 387600 7 D (250
Sqm) Medium Cost Medium technology Side and Top ventilation Poly house (As per Approved standard Design & Drawing , Annexure -A & B) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia 2 mm thick ( for Roll up), 20 mm dia, 2.35 mm thick (for Strut & Ties, purlin), 25 mm dia, 2.65 mm thick (for Horizontal, Ridge &Hoop & Short chord), 40 mm dia, 2.90 mm thick (for Column & King Post), 32 mm dia, 2.65 mm thick (for Long chord) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Alluminium Profile etc., Molding, Processing, fabrication and erection with all fittings and accessories
SpecificationS & Dimensions Length : 25.00 m. ( Spans at 2.50 m, each ), Breadth : 10.00 m. Side /Center height : 2.50/4.00+1 m top ventilation . (Semi circular type ). Of Sub Structure: Stanchions/ props : 40mm G.I. Pipe Top Arc with tie beam: 25mm G.I.Pipe Struts, Ties & Purlins : 20mm G.I.Pipe Of Door and End Frame: One door size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings . All M.S Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminium Profile only.
1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required .
3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation : Side ventilation roll up system provided on two sides from top of side prop to 1.50 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent mgration of insects - Pest and seepage of water from outside etc.. Top Ventilation : Top ventilation rollup system is to be provided with opening of 1.00meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top . Top open space /vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter the poly house. Insect Nets: U.V stabilized insect net of 20 to 40 mesh as per agro climatic conditions is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house.
Shade Nets: Removable fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should ve with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation up to 1.50meters & ii) All Round Ventilation . iv) Side /Central height 2.50/4.50m+1.00m top ventilation.
v) Side /Central height 3.00/5.00m +1.00m top ventilation.
vi) Arrangement for movable exterior/interior rolling type shading. vii) Side height of ventilation can be increased. viii) Height of fixed sheet from ground level can be decreased up to 0.75 mtr. ix) Annex double door. Farmers can got these optional features installed created .but exrtra cost if any will be paid / met by the farmers.
D1& D2 a)Without Shade net with UV. Film having specifications mentioned under Sr. No. 7 ( Item no 1&2). 250
Sqm 735.00 183750 -do- b) Without Shade net with UV. Film having specifications
mentioned under Sr. No. 7 (Item no 1,2 & 3). 250 Sqm 745.00 186250
D3 & D4
c) With U.V. Shade net 50% shading effect exterior/ interior fitted with UV. Film having specifications mentioned under Sr. No. 7 (Item no 1&2 ). 250
Sqm 770.00 192500 -do- d) With U.V. Shade net 50% shading effect exterior/ interior
fitted with UV. Film having specifications mentioned under Sr. No. 7 (Item no 1,2 & 3). 250
Sqm 775.00 193750 8 D-Hi
126 Sqm
Medium Cost Modified Side and Top ventilation Poly house (As per Approved standard Design & Drawing , Annexure -A& B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20mm dia and 2.35mm thick ( For vent ), 25 mm dia, 2.65 mm thick ( for Strut & Ties ,Purlin, Front and Back Support , Insect net), 32mm dia, 2.65 mm thick (for Top Vent and wind bracing & long beam ) , 40mm & 2.90mm thick ( For Semi Circular Arc , Ridge & Horizontal short Beam ), 50 mm dia, 2.90 mm thick (for Stanchion / Prop & King post) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories
Specifications and Dimensions Length : 12.00 m. ( Spans at 4.00 m each ), Breadth: 10.50 m. ( Spans at 5.25 m each ), Side / Center height: 3.20 / 4.60 +1 m top ventilation., Ridge height 5.60 m. Of Sub Structure: Stanchions/ props : 50 mm G.I. Pipe. Top Arc & Short beam: 40 mm G.I. Pipe.
Long Beam : 32 mm dia Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: One door size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I.Pipes of respective dias as mentioned in the drawings . All parts of M.S. should have duly painted first red oxide priming coat followed by brush painting (two coats) .
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2) The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on two sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.20 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest migration and seepage of water from outside etc. Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V satblized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior/ interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 4.00 m. iv) Fan pad system for cooling.
v) Adjustment in side & top ventilation space. vi) Height of fixd sheet from ground level can be decreased up to 0.75 mtr. vii) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
viii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmer can got these optional features installed / created , but extra cost if any will be paid / met by the farmers.
D-Hi- 1 Without Shade net with UV. Film having specifications mentioned under Sr. No. 8 (Item no. 1, 2 & 3). 126
Sqm 761.00 95886 D-Hi-2 With U.V. Shade net 50% shading effects interior / exterior
fitted with UV. Film having specifications mentioned under Sr. No. 8 (Item no 1, 2 & 3). 126
Sqm 781.00 98406 9 AD-Hi-
AL 252 Sqm
Medium Cost Modified Side and Top ventilation Poly house As per Approved standard Design & Drawing,( Annexure -A & B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20mm dia and 2.35mm thick (for purlin & along the insectnet, front & Back Support & vent Tie ), 25 mm dia, 2.65 mm thick ( for Strut & Ties , 32mm dia, 2.65 mm thick (for Top Vent and wind bracing & long beam ) , 40mm & 2.90mm thick ( For Semi Circular Arc , Ridge & Horizontal short Beam ), 50 mm dia, 2.90 mm thick (for Stanchion / Prop & King post) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories
Specifications and Dimensions Length : 12.00 m. ( Spans at 4.00 m each ), Breadth: 10.50 m. ( Spans at 5.25 m each ), Side / Center height: 3.20 / 4.60 +1 m top ventilation., Ridge height 5.60 m. Of Sub Structure: Stanchions/ props : 50 mm G.I. Pipe. Top Arc & Short beam: 40 mm G.I. Pipe. Long Beam : 32 mm dia Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: 1 No. door 1 m x 2 m made of 1.25″x 1.25″ M.S. square pipe (duly painted) with poly sheet.End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings . All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3) U.V. stabilized film should block U.V. Radiations below 380 nanometerof PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on two sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.20 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to to prevent migration of insects - Pest and seepage of water from outside etc.. Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V stablized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside of poly house. Shade Nets: Fixed type exterior/ interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 4.00 m. iv) Fan pad system for cooling. v) Adjustment in side & top ventilation space. vi) Height of fixd sheet from ground level can be decreased up to 0.75 mtr. vii) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
viii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers. ix) Annex double door. Farmers can got the optional features installed / created , but extra cost if any, will be paid / met by the farmers.
AD-Hi-Al 1
Without Shade net with UV. Film having specifications mentioned under Sr. No. 9 (Item no. 1, 2 & 3). 252
Sqm 760.00 191520 AD-Hi-
Al 2 With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 9(Item no 1, 2 & 3).
252 Sqm 800.00 201600
10 D-Hi-AL 504
Sqm
Medium Cost Modified Side and Top ventilation Poly house (As per Approved standard Design & Drawing , Annexure -A & B) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20mm dia and 2.35mm thick ( For vent ties, Purlin, Front & Back Support & Insectnet), 25 mm dia, 2.65 mm thick ( for Strut & Ties ), 32mm dia, 2.65 mm thick (for Top Vent and wind bracing & long beam ) , 40mm & 2.90mm thick ( For Semi Circular Arc , Ridge & Horizontal short Beam ), 50 mm dia, 2.90 mm thick (for Stanchion / Prop & King post) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories
Specifications and Dimensions Length : 24.00 m. ( Spans at 4.00 m each ), Breadth: 21.00 m. ( Spans at 5.25 m each ), Side / Center height: 3.20 / 4.60 +1 m top ventilation. Gutter height 3.20 m, Ridge height 5.60 m.
Of Sub Structure: Stanchions/ props : 50 mm G.I. Pipe. Top Arc & Short beam: 40 mm G.I. Pipe. Long Beam : 32 mm dia Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings. All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc. Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter. 1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380 nanometerof PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.20 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc. Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior/ interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 4.00 m. iv) Fan pad system for cooling. v) Adjustment in side & top ventilation space. vi) Height of fixed sheet from ground level can be decreased up to 0.75 mtr.
vi) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability. Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any, will be paid /met by the farmers.
D-Hi-Al 1 , D-
Hi-Al 2
Without Shade net with UV. Film having specifications mentioned under Sr. No.10(Item no. 1, 2 & 3). 504 +
6 Sqm 760.00 387600 D-Hi-Al 3 , D-
Hi-Al 4
With U.V. Shade net 50% sahding effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 10 (Item no 1, 2 & 3).
504 + 6 Sqm 788.00 401880
11 D-Hi-AL 504
Sqm (Hockey Type )
Medium Cost Modified Side and Top ventilation Poly house (Hockey Type as per Approved standard Design & Drawing ( Annexure A& B) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20 mm & 2.35mm thick ( For vent), 25 mm dia 2.65 mm thick ( for Sturt and Ties , Horizontal Beam, Purlin & Ridge), 50 mm dia, 2.90 mm thick (for Center Prop & Out side hockey Post, Semi-Circular Arcs ), 80 mm dia 3.25 mm thick (for main Side Vert. post), including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories.
Specification s and Dimensions : Length : 24.00 m. ( Span 6 Nos.4.00 m each ), Breadth: 21.00 m. ( Side Span 2 Nos. 2.50 m each, & 2 Nos. 8.00
m each ).
Side / Center height: 3.00 / 4.95 +1 m top ventilation. Gutter height 3.00 m, Ridge height 5.95 m.
Of Sub Structure: Stanchions/ props: 50 & 80 mm G.I. Pipe. Top Arc: 50 mm G.I. Pipe. Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: Two number Annex doors (1no.
Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings . All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter.
1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380 nanometer PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc..
Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house.
Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house .
Shade Nets: Fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 3.50 m. iv) Fan pad system for cooling. v) Adjustment in side & top ventilation space as per farmers choice.
vi) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
vii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any , will be paid / met by the farmers .
D-Hi-Al 5 , D-
Hi-Al 6
Without Shade net with UV. Film having specifications mentioned under Sr. No. 11 (Item no. 1, 2 & 3). 504 +
6 Sqm 761.00 388110 D-Hi-Al 7 , D-Hi-
Al 8
With U.V. Shade net 50% shading efect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 11 (Item no 1, 2 & 3).
504 + 6 Sqm 788.00 401880
12 D-Hi-AL 544
Sqm Hockey
Type
Medium Cost Modified Side and Top ventilation Poly house (Hockey Type as per standard ApprovedDesign & Drawing, Annexure -A & B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up of vent.), 20 mm dia 2.35 mm thick (for Top vent tie), 25 mm dia 2.65 mm thick ( for Strut & ties, Purlin, Insect net ), 40 mm dia, 2.90 mm thick (for Semi Circular Hoop & corridor), 50 mm dia, 2.90 mm thick (for Horizontal beam), 65 mm dia 3.25 mm thick (for vert. Post), including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories.
Specifications and Dimensions: Length : 28.00 m. ( Span 2 Nos. 2.00 m, 6 Nos. 4.00 m),
Breadth: 20.00 m. (Span 2 Nos. 2.00 m, 2 Nos. 4.00 m & 1 No. 8.00 m), Side / Center height: 3.00 / 5.00 +1 m top ventilation. Gutter height 4.50 m, Ridge height 6.00 m.
of Sub Structure: Stanchions/ props: 50 & 65 mm G.I. Pipe. Top Arc: 40 mm G.I. Pipe. Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dias as mentioned in the drawings . All the M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex. Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter. 1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to to prevent migration of insects - Pest and seepage of water from outside etc..
Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 top 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior / interior shading nets are is recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Fan pad system for cooling. iv) Side height 3.50 m. v) Adjustment in side & top ventilation space. vi)Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
vii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any, will be paid /met by the farmers.
D-Hi-Al 9 , D-Hi-
Al.10
Without Shade net with UV. Film having specifications mentioned under Sr. No. 12 (Item no. 1, 2 & 3).
544 + 6 Sqm 761.00 418550
D-Hi-Al11,
D-Hi-Al 12
With U.V. Shade net 50% effect exterior/ interior fitted with UV. Film having specifications mentioned under Sr. No. 12 (Item no 1, 2 & 3). 544 +
6 Sqm 775.00 426250 13 D-Hi-
AL 1008 Sqm
Medium Cost Modified Side and Top ventilation Poly house (As per Approved standard Design & Drawing , Annexure A& B) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20mm dia and 2.35mm thick ( For vent, Ties, Purlin, Front & Back Support & Insectnet), 25 mm dia, 2.65 mm thick ( for Strut & Ties), 32mm dia, 2.65 mm thick (for Top Vent and wind bracing & long beam ) , 40mm & 2.90mm thick ( For Semi Circular Arc , Ridge & Horizontal short Beam ), 50 mm dia, 2.90 mm thick (for Stanchion / Prop & King post) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories
Specifications and Dimensions : Length : 32.00 m. ( Spans at 4.00 m each ), Breadth: 31.50 m. ( Spans at 5.25 m each ), Side / Center height: 3.20 / 4.60 +1 m top ventilation. Gutter height 3.20 m, Ridge height 5.60 m.
Of Sub Structure: Stanchions/ props : 50 mm G.I. Pipe. Top Arc & Short beam: 40 mm G.I. Pipe. Long Beam : 32 mm dia Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dias as mentioned in the drawings.All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc. Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter. 1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard toprescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380 nanometerof PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.20 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc. Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house.
Shade Nets: Fixed type exterior/ interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 4.00 m. iv) Fan pad system for cooling. v) Adjustment in side & top ventilation space. vi) Height of fixed sheet from ground level can be decreased up to 0.75 mtr.
vi) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability. Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , bu textra cost if any , will be paid /met by the farmers.
AD-Hi-Al 13
Without Shade net with UV. Film having specifications mentioned under Sr. No. 13 (Item no. 1, 2 & 3). 1008 +
6 Sqm 761.00 771654 AD-Hi-Al 14
With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 13(Item no 1, 2 & 3).
1008 + 6 Sqm 785.00 795990
14 D-Hi-AL
1000 Sqm
Medium Cost Modified Side and Top ventilation Poly house (Hockey Type as per Approved standard Design & Drawing , Annexure -A &B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up of vent.), 20 mm dia 2.35 mm thick (for Top vent tie.), 25 mm dia 2.65 mm thick ( for Strut & Ties), 40 mm dia, 2.90 mm thick (for Semi Circular Hoop & corridor), 50 mm dia, 2.90 mm thick (for Horizontal beam), 65 mm dia 3.25 mm thick (for vert. Post), including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories.
Specifications and Dimensions Length : 36.00 m. ( Span 2 Nos. 2.00 m, 2Nos. 4.00 m, 3 Nos. 8.00 m), Breadth: 28.00 m. (Span 2 Nos. 2.00 m, 6 Nos. 4.00 m
Side / Center height: 3.00 / 5.00 +1 m top ventilation. Gutter height 4.50 m, Ridge height 6.00 m.
Of Sub Structure: Stanchions/ props: 50 & 65 mm G.I. Pipe. Top Arc: 40 mm G.I. Pipe. Roll up System: 15 mm dia G.I. Pipe.
Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dias as mentioned in the drawings. All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats). (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter.
1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc..
Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 top 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house.
Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house.
Shade Nets: Fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting.
iii) Fan pad system for cooling. iv) Side height 3.50 m. v) Adjustment in side & top ventilation space.
vi)Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
vii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any, will be paid / met by the farmers.
D-Hi-Al
- 15 Without Shade net with UV. Film having specifications mentioned under Sr. No.14(Item no. 1, 2 & 3). 1000 +
6 Sqm 761.00 765566 D-Hi-Al
- 16 With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No. 14 (Item no 1, 2 & 3). 1000 +
6 Sqm 780.00 784680 15 D-Hi-
AL 1000 Sqm
Hockey Type Saw
Tooth
Medium Cost Modified Side and Top ventilation Poly house (Hockey Type as per Approved standard Design & Drawing, Annexure A & B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up of vent.), 20 mm dia 2.35 mm thick (for Top vent tie.), 25 mm dia 2.65 mm thick ( for Strut & Ties, Purlin, & Insectnet), 40 mm dia, 2.90 mm thick (for Semi Circular Hoop & corridor, & Long beam), 50 mm dia, 2.90 mm thick (for Horizontal Short beam), 65 mm dia 3.25 mm thick (for vert. Post Center three row) 80 mm dia (for Side Vert.Post), including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories.
Specifications and Dimensions : Length : 36.00 m. ( Span 2 Nos. 2.00 m, 8Nos. 4.00 m),
Breadth: 28.00 m. (Span 2 Nos. 2.00 m, 4Nos. 6.00 m
Side / Center height: 4.50 +(2.10 m for 2 No. top ventilation & 1 No. Ventilation 0.60 m.) Gutter height 4.50 m , Ridge height 6.50 m. &
Of Sub Structure: Stanchions/ props: 80 & 65 mm G.I. Pipe. Top Arc / corridor: 40 mm G.I. Pipe. Roll up System: 15 mm dia G.I. Pipe.
Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I. Pipes of respective dias as mentioned in the drawings . All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with
suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2
Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter.
1) Poly film should have a minimum warrantee of 2 years with
regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2) The minimum thickness of the poly film will be 200 micron. The
poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard toprescribed specifications are also required.
3) U.V. stabilized film should block U.V. Radiations below 380
nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Side Ventilation: Side ventilation roll up system provided on four
sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc..
Top Ventilation: Top ventilation roll-up system is to be provided
with opening of 2.10 &0.60 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 top 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house.
Insect Nets: U.V stabilized insect net of 20 to 40 mesh is to be
provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house.
Shade Nets: Fixed type exterior / interior U.V. shading nets are
recommended which can be removed as and when required and Shade nets should be with 50% shading effect .The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility.
Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Fan pad system for cooling. iv) Side height 3.50 m. v) Adjustment in side & top ventilation space. vi)Any other fixtures as per requirement of the farmer without
disturbing the over all structural stability.
vii) Arrangement for movable exterior/interior rolling type shading
as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any, will be paid /met by the farmers.
D-Hi-Al
17 Without Shade net with UV. Film having specifications mentioned under Sr. No. 15(Item no. 1, 2 & 3). 1000 +
6 Sqm 761.00 765566 D-Hi-Al
18 With U.V. Shade net 50% shading effect exterior / interior fitted with UV. Film having specifications mentioned under Sr. No.15(Item no 1, 2 & 3). 1000 +
6 Sqm 788.00 792728 16 D-Hi-Al
1008 Sqm
Hockey
Medium Cost Modified Side and Top ventilation Poly house (Hockey Type as per Approved standard Design & Drawing , Annexure -A & B ) with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 15 mm dia, 2 mm thick ( for Roll up .), 20 mm & 2.35mm thick ( For vent), 25 mm dia 2.65 mm thick ( for Sturt and Ties , Horizontal Beam, Purlin & Ridge), 50 mm dia, 2.90 mm thick (for Center Prop & Out side hockey Post, Semi-Circular Arcs ), 80 mm dia 3.25 mm thick (for main Side Vert. post), including earth work in foundation & C.C. 1:3:6 for encasing column pipe including Aluminum Profile etc., Molding, Processing fabrication and erection with all fittings and accessories.
Specifications and Dimensions : Length : 36.00 m. ( Span 2 Nos.2.00 m each + 4Nos. 8 m),
Breadth: 28.00 m. ( Span 7 Nos. 4.00m each ). Side / Center height: 3.00 / 4.95 +1 m top ventilation. Gutter height 3.00 m, Ridge height 5.95 m.
Of Sub Structure: Stanchions/ props: 50 & 80 mm G.I. Pipe. Top Arc: 50 mm G.I. Pipe. Roll up System: 15 mm dia G.I. Pipe. Of Door and End Frame: Two number Annex doors (1no. Sliding inside & 1no.fixed with hinges out side) size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet. End frames fabricated of G.I.Pipes of respective dia as mentioned in the drawings. All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) . (Annex Size: 2 m x 3 m) both Doors are to be installed with annex.
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. Aluminum profile etc.
Of Gutter: i) 0.8 mm thick P.G.I. Sheet to be supported by 2 Nos. G.I. Pipe 20 mm dia at Bottom. or ii) 2.0 mm thick P.G.I. Sheet Gutter. 1) Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same. 2) The minimum thickness of the poly film will be 200 micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required. 3) U.V. stabilized film should block U.V. Radiations below 380 nanometer PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc. Side Ventilation: Side ventilation roll up system provided on four sides from top of side prop to 2.00 m downward and is designed to open from bottom to top using hand operated mechanism. From ground level to 1.00 m height is to be provided with a strip of U.V. Sheet in order to prevent drafts in and around the ground area. Sheet shall be buried in the ground on the lower side up to minimum depth of 40 cm to prevent migration of insects - Pest and seepage of water from outside etc.. Top Ventilation: Top ventilation roll-up system is to be provided with opening of 1.00 meter which is to be operated by hand operated mechanism and designed to be operated from bottom to top. Top open space / vent is to be covered with 20 to 40 mesh U.V. stabilized insect net. The vent hoop should be sufficiently extended so that rain water/ rain showers do not enter in the poly house. Insect Nets: U.V stablized insect net of 20 to 40 mesh is to be provided in the side walls and top vents , wherever applicable as per opening space/vents and tightly fitted to provide natural ventilation and to prevent entry of insects inside the poly house. Shade Nets: Fixed type exterior / interior U.V. shading nets are recommended which can be removed as and when required and Shade nets should be with 50% shading effect and nets should be U.V. stabilized.The shade nets can also be fixed inside poly houses for better and easy workability and as per choice of farmers, with manual folding & spreading facility. Optional:- i) Top Ventilation up to 1.50 m height. ii) Side Gutter for Roof Top water harvesting. iii) Side height 3.50 m. iv) Fan pad system for cooling. v) Adjustment in side & top ventilation space as per farmers choice.
vi) Any other fixtures as per requirement of the farmer without disturbing the over all structural stability.
vii) Arrangement for movable exterior/interior rolling type shading as per choice of farmers . Farmers can got these optional features installed / created , but extra cost if any, will be paid / met by the farmers.
D-Hi-Al - 19
Without Shade net with UV. Film having specifications mentioned under Sr. No.16 (Item no. 1, 2 & 3). 1008 +
6 Sqm 761.00 771654 D-Hi-Al
- 20 With U.V. Shade net 50% shading effect exterior/ interior fitted with UV. Film having specifications mentioned under Sr. No. 16(Item no 1, 2 & 3). 1008 +
6 Sqm 788.00 799032 17 Z (40
Sqm) Low technology Special Model Poly house for Snow Bound Area Without Shade net with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 25 mm dia 2.65 mm thick (for Horizontal), 40 mm dia, 2.90 mm thick (for Column) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including G.I. Profile etc., Molding, Processing ,fabrication and erection with all fittings and accessories. The top surface is to be fixed with G.I. Wire mesh 150x150mm size, 4mm thick G.I. Wire conforming to IS 2721-2003, galvanizing heavy coated with zinc as per IS. 4826-1968 or IS 12753.
Specifications and Dimensions Length : 10.00 m. ( Spans at 2.00m each ),
Breadth : 4.00 m.
Side height : 2.75m on higher side and 1.75m on shorter side
Of Sub Structure: Stanchions/ props : 40mm G.I. Pipe
Horizontal purlin etc. 25mm
G.I.Pipe Of Door and End Frame:
One door size 1mx2m made of 1.25″x1.25″ M.S. square pipe (duly painted) with poly sheet . End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings . All M.S. Parts should have Square pipes duly painted first red oxide priming coat followed by brush painting (two coats ).
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. G.I. Profile etc.
1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3)U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Optional:- i) Side height 2.50/1.50m.
ii) Lower side and Short side supported with brick masonry 0.50m
height.
iii)All sides with G.I. Wire mesh for protection from wild and domestic animals.
Farmers can got these optional features installed / created , but extra cost if any, will be paid / met by the farmers.
Z1 Without Shade net with UV. Film having specifications mentioned under Sr. No. 17 (Item no 1,2 & 3). 40
Sqm 1050.00 42000 18 Z3(40
Sqm) Medium technology Special Model Poly house for Snow Bound Area Without Shade net with G.I. Pipe (A Class) Hot galvanized ISI 1239 marked of different dia meters and Galvanization as per IS-Code 4736 Size varying from 32 mm dia ,2.65 mm thick (for Horizontal), 40 mm dia, 2.90 mm thick (for Column) including earth work in foundation & C.C. 1:3:6 for encasing column pipe including G.I. Profile etc., Molding, Processing ,fabrication and erection with all fittings and accessories.
Specifications and Dimensions Length : 10.00 m. ( Spans at 2.00m each ), Breadth : 4.00 m. Side /Centre height : 1.50/3.50m Of Sub Structure: Stanchions/ props : 40mm G.I. Pipe Horizontal purlin etc. 25mm G.I.Pipe Top Gothic Arc with tie beam: 32mm G.I.Pipe Struts& Ties : 25mm G.I.Pipe Of Door and End Frame: One door size 1mx2m made from 1.25″x1.25″ M.S. square pipe duly painted with poly sheet . End frames fabricated of G.I. Pipes of respective dia as mentioned in the drawings. All M.S. Parts should have duly painted first red oxide priming coat followed by brush painting (two coats) .
Of Cladding Material / U.V. Poly Films: Covering with suitable U.V. stabilized poly sheet, the sheet is to be attached to the structure for quick removal and fixing i.e. G.I. Profile etc.
1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same.
2)The minimum thickness of the poly film will be 200micron. The poly film should have ISO certification and conform to ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to prescribed specifications are also required.
3)U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.
Optional:- i) Side height 2.00/4.50m. ii) Ventilation of appropriate sizes and roll up type side ventilation with hand operated mechanization .
ii) All side supported with brick masonry 0.50m height.
iii)All sides with G.I. Wire mesh for protection from wild and domestic animals.
Farmers can got these optional features installed / created , but extra cost if any, will be paid / met by the farmers.
Z3 Without Shade net with UV. Film having specifications mentioned
under Sr. No. 18 (Item no 1,2 & 3). 40
Sqm 1050.00 42000 19 Consruction of Poly house :
Percentage hike for the construction of poly house structures of (All Models) in trible areas to meet out the higher construction cost due to enhanced labour rates and carriage of material etc.
%age
20% above the basic rates
Specifications For Extra Models of Poly- Houses Structures and Model -wise Approved Rate per Sqm Covered area. Sr. No. Description Covered Area
(Sqm) Approved Rates (Rs.)
1 2 3 41 Specifiaction of Tunnels of Disfferent Sizes ( T2) Length ;- 15.00m x 8 m ,
Spacining between Polls -3.0m , Side height - 1 to 1.50m , Centre Height:- 3.50 to 4.00m and made of coated pipe of 40& 32mm dia having thickness 1.80mm , Covering Material _ Tunnels will be covered 140 GSM Woven Fabric from PIC PLAST LTD. ISRAEL. on two side along with 40mesh insect net will be provided 120 500
2 Specifiaction of Tunnels of Disfferent Sizes ( T3) Length ;- 24.00m x 8 m , Spacining between Polls -3.0m , Side height - 1 to 1.50m , Centre Height:- 3.50 to 4.00m and made of coated pipe of 32mm dia having thickness 1.80mm , Covering Material _ Tunnels will be covered 140 GSM Woven Fabric from PIC PLAST LTD. ISRAEL. on two side along with 40mesh insect net will be provided
192 445
3 (Edke -Type Model A standard) Low Cost Modified side ventilation EDKE-Type Polyhouse approved 15mm dia and 1.5-1.7 mmthick G.I. Pipes for foundation processing, fabrication and erection with all fittings and accessories or prefabricated kits of complete material set.
20,40,60,80,100,120,134& 140
340+ VAT and Service Tax
Length up to 28.0m (Span at 4.00m each)
Breadth =5.00m
Side /Central Height :-2.10/3.60m(Saw Tooth Type)
Column : Twin Bamboo joined bolts and bonded by 4 feet long and 15mm dia G.I. Pipe in conc.
Arcs, Ties, Beams( Bamboo)
4 (Edke -Type Model B Cascaded) Low Cost Modified side ventilation EDKE-Type Polyhouse approved 15mm dia and 1.5-1.7 mmthick G.I. Pipes for foundation processing, fabrication and erection with all fittings and accessories or prefabricated kits of complete material set. This model is for terraced land on slopes.
20,40,60,80,100,120,134& 140
362+ VAT and Service Tax
Length up to 28.0m (Span at 4.00m each)
Breadth =5.00m
Side and Central Height :-2.10m in casacaded type slopes.
Column : Twin Bamboo joined bolts and bonded by 4 feet long and 15mm dia G.I. Pipe in conc.
Arcs, Ties, Beams( Bamboo)
For extra - Models, the following companies are empannelled for the construction Work
a) For Models at Sr.No. 1&2
1 M/S Classic Agri Con Panchkulla Haryana. 2 M/S Complete Green House Soution Pvt. Ltd.
Panchkulla Haryana
3 M/S Green Tech Agr. Sec. Pvt. Ltd. Ner Chowk Mandi.
b) For Bamboo Models Poly -Houses
1 M/S Thousand Petals , Poly Housees Pvt. Ltd. 8/86, Dashabhuja Apts, Rambaug Colont, Paud Road , Kothrud, Pune 411038
Annexure-IV
Specifications for Providing & Supply of Cladding Materials , Approved Rates per Sqm. Sr.No. Specification of Cladding Material Unit Approved
Rate per Sqm. (Rs.)
1 2 3 4 1 Supply of Cladding Material / U.V. Poly Films:
1)Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same and the minimum thickness of the poly film will be 200micron . The poly film should have ISO certification and ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to given specifications are also required.Samples measuring 6 x6 cms depicting specifications of U.V. Films are also required with the offer. The firms /companies are also required to quote brand name and specifications of U.V.Films which they intend to use incuding U.V.Sheet number etc.
Supply of Cladding Material / U.V. Films (a)1 &2 (Sq m) 37.00
2 Supply of Cladding Material / U.V. Poly Films:Poly film should have a minimum warrantee of 2 years with regard to U.V. stabilization and should have more than 70% transmittance during the first two years and not less than 65% during the entire life of the poly films. In the event of spoilage / degradations prior to the agreed productive life, the firm/ company is liable to replace the same and the minimum thickness of the poly film will be 200micron . The poly films should have ISO certification and ISI specifications. Test reports of approved test houses or test report from manufacturer with regard to given specifications are also required . U.V. stabilized film should block U.V. radiations below 380 nanometer of PAR Light. Poly film should have good thermic effect more than 60%. Films should have properties like anti-drip, anti- fog, anti-dust, light diffusion capacity above 50% etc.Samples measuring 6x 6 cms depicting specifications of U.V.Films are also required with the offer. The firms/ companies are also required to quote brand name and specifications of U.V.Films which they intend to use including U.V. sheet numbers etc.
Supply of Cladding Material / U.V. Films (b )1,2&3 Sqm 42.00
3 a) Supply of U.V. Stabilized multilayered x-laminated sheet as per IS 14611:1998 Specifications (For Pond Lining and Sub -surface dyke ) Samples measuring 6 x6 cms depicting specifications of U.V. Films are also required with the offer. The firms /companies are also required to quote brand name and specifications of U.V.Films which they intend to use incuding U.V.Sheet number etc.
120 GSM Sqm 46.50 150 GSM Sqm 60.00 200 GSM Sqm 81.10 250GSM Sqm 94.00 300GSM Sqm. 116.00 400GSM Sqm 140.00 500 GSM Sqm 205.00
b)Woven /Extruded GEO Membrane 120GSM Sqm 48.00 150 GSM Sqm 65.00 200 GSM Sqm 78.00 250GSM Sqm 98.00 400GSM Sqm 160.00 500 GSM Sqm 198.00
c) WOVEN GEO-Textiles 120GSM Sqm 65.00
150GSM Sqm 76.00 200 GSM Sqm 102.00 250GSM Sqm 124.00 400GSM Sqm 209.00 500 GSM Sqm 255.00
4 Any other special films with complete specifications 1) IS 2508 - 500 micron , 2) IS 15351- 500 micron
Sqm 120.00
Sqm 130.00 Mulching film Black 25-200 micron Kg. 250.00 Trough Sheet B/W Kg. 250.00 Green House Gutter lining sheet Kg. 250.00 Soil Soalrization film Kg. 225.00 Low tunnel sheet 100 micron Sq.Mtr. 25.00 Mulch MoT/ Weed Control mat 80 GSM Sq.Mtr. 35.00 Woven Laminated UV Sheet for Green House Applications 1) 150GSM Anti Dust , Anti Fog, Diffused Sq.Mtr. 48.00 2) 160GSM Anti Dust , Anti Fog Diffused Sq.Mtr. 54.00 3)172 GSM Anti Dust , Anti Fog, Thermic Diffused ,AV. Anti Sulpher (Optional) Sq.Mtr. 65.00
5 For poly film, having 1 and 2 specifications with added advantage of partial diffusion of light( 20 to 25% diffusion) and thermicity 45 to 50 %
Sq.Mtrs 40.00
List of Authorised suppliers for different type of Cladding Material
A) Poly -Films with specifications 1&2 1 M/S Shivalik Agro- Engineers Near DAV School , Kather ,
Bye Pass Road ,Solan
2 M/S Classic Agri Con Panchkulla Haryana. 3 M/S Complete Green House Soution Pvt. Ltd. Panchkulla
Haryana
4 M/S Green Tech Agr. Sec. Pvt. Ltd. Ner Chowk Mandi. 5 M/S Jain Irrigation System Ltd. Sundernagar, Mandi.
6 M/S Phuar Agrotech, Todapur, New Delhi. 7 M/S Finolex Plasson India Ltd. Ursa Taluka Maval, Pune. 8 M/S Vij Brothers, Hoshiarpur (Pb). 9 M/S Sheel Bio Tech Ltd. Greater Kailash, New Delhi. 10 M/S Churrah Valley Fruit & Veg. Copt. Bhanjraru, Chamba
11 M/S Rajdeep Agr. Products New Delhi. 12 M/S Thakur Brothers , Bilaspur 13 M/S Swati Store Wel Pvt. Parwanoo. B) UV Film with Specifications 1,2 & 3 As above 1 to 13 at Sr. No. A C) UV Stabilized multilayered x-laminated sheet as
per IS 14611:1998 Specifications (For Pond Lining and Sub -surface dyke ) for 120,150,200,250,300, 400& 500 GSM sheet
1 M/S Surya Structurals Solan. D) Woven /Extruded GEO Membrane and WOVEN
GEO-Textiles (For pond lining and subsurface dykes) 1 M/S Shivalik Agro- Engineers Near DAV School , Kather ,
Bye Pass Road ,Solan 2 M/S Green Tech Agr. Sec. Pvt. Ltd. Ner Chowk Mandi.
3 M/S Phuar Agrotech, Todapur, New Delhi. E) Any other special films with complete
specifications 1) IS 2508 - 500 micron , 2) IS 15351- 500 micron
Part -A i) IS 2508 - 500 micron , ii) IS 15351- 500 micron 1 M/S Finolex Plasson India Ltd. Ursa Taluka Maval, Pune.
Part -B Mulching film Black 25-200 micron Trough Sheet B/W Green House Gutter lining sheet Soil Soalrization film Low tunnel sheet 100 micron
Mulch MoT/ Weed Control mat 80 GSM Woven Laminated UV Sheet for Green House
Applications
1) 150GSM Anti Dust , Anti Fog, Diffused 2) 160GSM Anti Dust , Anti Fog Diffused 3)172 GSM Anti Dust , Anti Fog, Thermic Diffused ,AV.
Anti Sulpher (Optional)
For poly film, having 1 and 2 specifications with added advantage of partial diffusion of light( 20 to 25% diffusion) and thermicity 45 to 50 %
1 Shivalik Agro-Engineers Near DAV School , Kather Bye Pass Road, Solan
Annexure-IV
SPECIFICATIONS OF G.I. PIPES. Pipes Conforming to Indian Standards. (A) Mild Steel Tubes, Tubulars and Other wrought Steel Fittings – Part –I, MILD STEEL
TUBES (from IS – 1239).
Galvanising :- Galvanises with the Zinc coating conforming to IS Code : 4736 .(Hot Dip zinc coatings on steel tubes. The above standard gives due consideration to international standards and has derived the
assistance for BS – 1387. Steel tubes and tubulars suitable for screwing to B.S – 21 pipe threads. The scope of this standard covers the requirement for butt welded and seamless, screwed and socketed and plain end mild steel tubes.
The pipe under this standard are designated by their nominal bore and are further classified
as ‘Light’, ‘Medium’, and ‘Heavy’ depending upon their wall thickness. Ordinarily all the three categories of pipes may be used for conveying gas and water. Only Medium and Heavy pipes are recommended for carrying steam. Sockets of these tubes are designated by respective nominal bore of the pipe.
Manufacturing Process: Tubes are made from tested quality of steel manufactured by any approved process (a) Hot Finished Seamless (HFS), (b) Electric Resistance Welded (ERW), (c) High Frequency Induction Welded (HFIW), and (d) Hot Finished Welded (HFW). Tubes manufactured by manual welding are covered by this standard. Light, Medium and Heavy tubes and all sockets shall be either welded or seamless. Medium and heavy tubes shall be manufactured from mild steel by the open hearth, electric or basic oxygen process. All electric welded tubes and sockets (Medium and Heavy) class shall be normalised. Tensile Strength: The tensile strength of strips cut from selected tubes shall be at least 320 MPa. Chemical Composition: The ladle analysis of steel for tubes and sockets used for steam services shall not show sulphur and phosphorus in amount exceeding 0.050 percent each. When pipes are used for water and gas purposes these contents shall not exceed 0.060 percent each. Tolerance: The manufacturing tolerance to the following extent is permissible on pipes and sockets: Butt Welded: Light tubes – 8 percent + not limited. Medium and Heavy tubes: - 10 percent + not limited.
Seamless tubes: - 12.5 percent + not limited. Weights:
(1) Single tube Light – 8 percent + 10 percent.
(2) Single tube Medium and Heavy – 8 percent + 10 percent.
(3) Form quantities per Load of 10 tonnes Min. (Light Series) ± 5 percent.
(4) The quantity per load of 10 tonnes Min. (Medium & Heavy series) ± 7.5 percent. Note: For the purpose of minimum weighment of 10 tonnes lot, the weighment may be done in
convenient lots at the option of the manufacturer. TABLE 87 Dimension and Nominal Weights of Black steel Tubes (LIGHT) IS – 1239. N.B.
mm
O.D. Thickness
mm
Weight of Black Tube Calculated nominal wt. of Galvanised Tubes.
Max
mm
Min
mm
Plain end
Kg/m
Screwed and Socketed
Kg/m
Plain end
Kg/m
Screwed and Socketed
Kg/m 15 20 25 32 40 50 65 80
100
21.4 26.9 33.8 42.5 48.4 60.2 76.0 88.7
113.90
21.0 26.4 33.2 41.9 47.0 59.6 75.2 87.9 113.0
2.00 2.35 2.65 2.65 2.90 2.90 3.25 3.25 3.65
0.952 1.41 2.01 2.58 3.25 4.11 5.80 6.81 9.89
0.961 1.42 2.03 2.61 3.29 4.18 5.90 6.98 10.20
1.02 1.49 2.11 2.71 3.39 4.29 6.04 7.06
10.21
1.03 1.50 2.13 2.74 3.43 4.36 6.11 7.29 10.51
Annexure-VI
AGREEMENT BETWEEN FARMER AND THE COMPANY (SERVICE PROVIDER) FOR THE CONSTRUCTION OF POLY HOUSES AND INSTALLATION OF MICRO
IRRIGATION SYSTEM (On judicial paper to be attested by 1st Class Magistrate/Notary)
This agreement made this __________________ day of ________
between Sh. /Smt._________________________________ R/O __________________
__________________________ (hereinafter called the company (Service provider) or the
second party. (The agreement will be signed by proprietor of the firm/company or authorised
representative duly authorised by the firm or company)
The parties hereby agreed to undertake the following:
1. The farmers or first party will provide well levelled land to the firm/company for the
construction of poly house and also provide water source for the installation and
opertionalisation of micro irrigation system preferably within 20 meter radius of the
constructed poly house. The first party will bear the head load carriage from Katchha
/pucca road head to the actual site of poly house.
2. The first party will select the model and design of poly house of his choice from the
approved models and designs and will provide cheque/draft to the company equal to
20% of the cost as beneficiary share at the time of signing of agreement.
3. The first party will get the infrastructure installed from second party of total cost of
construction of poly house/poly houses and MI system or any one component as per
status of empanelment of the company in accordance with the approved model,
design, specification and rate.
4. The second party approved by the Govt. will arrange specified construction material
and will execute the work to the best satisfaction of first party within 90 days from the
date of signing of the agreement.
5. The second party will get the construction material inspected by the PIA or his
authorised representative and will get the inspection/verification certificate.
6. In case of default/deviation from the agreed terms and conditions, the parties
concerned will be liable for the following:
(a) Loss accrued to the first party by way of non construction of structure/ installation
of irrigation system within 90 days, second party will be liable to refund the entire
amount with 20% interest from the date of deposit of this amount. In case there is
any construction defect or non specified construction material is used, then second
party would remove the defect and replace the material at his own cost.
(b) First party shall have to sign an agreement with the service provider of his choice
within 15 days from the receipt of sanction from DNO.
(c) The execution of civil works will be decided mutually by both the parties.
In witness whereof the said ___________________ and
______________________ have hereto respectively signed this agreement on the day year
first hereinabove written.
Signature Witness 1.__________________________(PIA or his representative) Farmer (First party) 2.__________________________(Local person) Company (Service Provider)
Annexure-VIII Terms and conditions to be followed/observed by the companies short listed on the basis of technical and financial bids to act as Service Providers for the constructions of Poly Houses and Installation of micro irrigation systems i.e. Part-A and Part-B under Pt. Deen Dayal Kisan Bagwan Samridhi Yojna
1. That the company will execute Part-A or Part-B or Part-A+ Part-B of the project as
per approved designs for different models of Poly-houses ,Micro-Irrigation systems
and specifications prescribed for construction material on the rates approved by the
Govt.
2. The approved rates shall be applicable for one year in the first instance and the period
can be extended depending upon the need and requirement or till the new rates are
finalized. Copy of approved designs of different models and sizes alongwith
specifications of construction material and approved rates per sqm. are enclosed as
per Annexure ‘A’. Approved rates per sq.m. for installation of M.I systems inside
Poly houses are enclosed as per Annexure-B.
3. The approved rates are inclusive of all taxes but are exclusive of cost of development
of site.
4. The approved rates are for planning, designing alongwith providing, fixing and
installation of systems as per project targets.
5. The infrastructure to be constructed / installed on behalf of the farmers by the
company will be under warranty for 2 years and therefore any damage to the installed
system/structure, due to defective construction will be rectified/ corrected by the
company free of cost.
6. The company will provide after sale service facilities at focal points in all the districts
where they are working. The department will not ensure any work volume to the
company. However in view of spirit of the project, the project benefits must flow to
the farming community evenly through out the State. To ensure this, department can
fix minimum targets to the company with respect to hard areas including backward
Panchayats and tribal pockets.
7. The company will have to exhibit counter samples of essential components in the
office outlets in each districts/focal points so that DNO’s/PIA’s/farmers can verify the
quality of components to be used for installation of the systems or used in the
installed infra-structure.
8. The empanelment fee of Rs.25000/- for each component i.e. Part A for installation of
Poly –house or Part –B for installation of MI systems inside poly houses and Rs.
50000/- for installation of both components (Part A+ Part B ) is non refundable is
required to be deposited before empanelment of the companies and the same shall be
used by the department for training, exposure and promotion of precision farming
practices and for transfer of relevant technological interventions.
9. The company shall have to complete the construction of poly house structures in all
respects within 90 days from the day when agreement is signed with the farmer. For
the installation of MI system inside the poly house ,the time limit is 30 days from the
date of completion of poly house structure in all respects. The agreement for the
installation of MI system would be signed simultaneously i.e. for Part-A and Part-B.
It is mandatory that farmers will deposit his contribution i.e. 20% at the time of
signing of agreement for both the components. For delay in construction, the
company would be liable to refund the entire amount taken from the farmer with
20% interest per annum and the interest shall be charged from the date of signing of
the agreement.
10. The company will bear the carriage charges upto road head pucca and kachha as the
rates approved are inclusive of these charges. However, any head load beyond road
head shall be borne by the beneficiaries.
11. Fan Pad System has not been provided for any model of poly house. However, it is
open to the beneficiaries to install the same at his own cost. Also other facilities like
light arrangements, temperature and humidity recording devices can be installed by
the beneficiary at his own expenses. All other optional items mentioned in the
drawing of models can be installed for which the expenditure is to be borne by the
farmer or as per mutual agreement of farmer with service provider.
12. The cost of pumping unit has not been included in the rates approved for the
installation of micro irrigation system. Therefore, the cost of pumping units shall be
borne by the beneficiaries.
13. The constructed poly house structure and installed micro irrigation system will be
inspected by the designated officers of the department or by the third party as the case
may be for different parameters like quality, workability and sustainability.
14. The companies are not only required to install infrastructure in a time bound manner
but it has to be workable, smooth and safe for UV film and construction should be to
the best satisfaction of beneficiary /PIA.
15. Project assistance would be released to the beneficiary after completion and joint
inspection conducted by the Department and the bankers in case bank loan is availed.
The bank draft shall be handed over to the company through the farmer by the PIA
after their full satisfaction. The payment can be released after the completion of even
single component i.e. poly house or MI.
16. Before actual execution, the company and the beneficiary shall have to sign a legally
valid contract as per agreement form Annexure-VI of the operational guidelines.
17. No billing is allowed from outside the state so the companies will have to obtain the
necessary TIN No. within 15 days from the date of empanelment.
18. The company is being empanelled provisionally and decision for regular empanelment
will be taken after two months from this date and the same shall depend upon
fulfillment of terms and conditions provided in the technical and financial bids at Sr.
No. 1 to 9 and 1 to 24 respectively . In the event of non fulfillment of agreed terms
and conditions, the company is liable to be de-empanelled.
19. Any departure from the agreed terms and conditions stipulated in the technical and
financial bids and enlisted above from 1 to 18 shall tantamount to recovery of the
amount equal to default with interest and the same can be changed to the bank
guarantee of Rs.5 lac. For repeated violation of agreed terms and conditions, the
company would be liable for de-empanelment or black listing as the case may be.
However, before de-empanelment or blacklisting, the matter shall be referred to the
Govt.
The operational guidelines of the scheme are available on the website of the Department of Agriculture i.e. www.hpagriculture.com.
Annexure-IX List of companies who have been empanelled as Service Providers under
Pt. Deen Dayal Kisan Bagwan Samridhi Yojna Part-I for the year 2010-11 (a) Poly houses: S.No. Name and Address of the
Company Contact/ Fax No. E-mail Remarks
A. Construction of Poly houses (Part-A): 1. M/s Shashanka Agro Tech Pvt.
Ltd., Harihar SinghRoad, Mora Badi, Ranchi – 834008
0651-6453746, -2552224(Fax),
Part-A
2 M/s Bhoomi Agro Tech, Opp. H.P. State Co-operative Bank V & P.O. Kandraur, Teh. & Distt. Bilaspur, H.P.
092184-05541 Bhoomi agrotech@ gmail.com
Part-A
3. M/S Nikhil Green House Huts Development & Hi Tech Agro Engineers Kansa Chowk-Mandi,H.P.
01905-310722 Mobile-93188-87504
- Part-A
4. Sai Engineering Foundation, Sai Bhawan,Sector-4, New Shimla-171009
0177-2670349, -2671268
Fax-2672915
Part-A
5. M/S Him Green Agro, 11-C,Industrial Area, Shoghi, Distt.Shimla-173219 (H.P.)
94810-51905, Fax-0177-2811213
Part-A
6. M/S Sai Steel Co and Company,V&P.O.Didhwin Tikker,Teh and Distt. Hamirpur
94180-90947 01972-255073
- Part-A
7. Sheel Biotech Ltd, RZ-2705/30,Sheel House,Main Jagdamba Road,Tuglakabad Ext.N Delhi-19
011-2994440, Fax: 011-2993450
Part-A
8. M/S Vijay RemediesLimited, VillageBhuranwala, Baddiroad, Barotiwala, Distt.Solan,H.P.
01792-255196,255382 Fax:0172-5057261
- Part-A
9. M/S Joshi Enterprises,Naya
Bazar,Theog,Distt.Shimla-1 Tel:01783-238051,
94180-38051 - Part-A
10. M/S Green Tech Agri. Sector Pvt.
Ltd.Corp.Off: Lunapani(Ner chowk) P.O.Nagchala, Distt. Mandi,H.P.
Tel:01905-242201, 94180-10744
Part-A
11. M/S Saveer Bio Tech Limited, Rgd.Off:1442,Wazir Nagar,Kotla Mubarakpur,New Delhi,-110003
Tel:01124622869,24647046Fax:011-
24620211,24643326
[email protected] Part-A
12. M/S Surya Structurals,Bye Pass Road,Kather-Solan-173212
Mobile-94180-74390 Telefax:01792-222707
Part-A
13. M/S Swati Indutries,Near Tel: 01792-221307, justashwani@gmai Part-A
Saproon Post Office, Saproon, Solan-173211 H.P.
Fax: 01792-220765 Mobile-94184-07788
l.com
14. M/S Phuar Agro Tech,WZ-75,Todapur,New Delhi-110012
Tel:093126-40985,098183-70496
Fax:011-25844180
Part-A
15. M/S FloriTech India, H/O:17B,DGBR,KarolBagh,New Delhi-110005
Tel:011-25727031(Telefax)
Mobile:09811042265
Part-A
16. M/S Thakur Brothers,Green House Consultants,Village-Kothi,P.O.Chandpur,Tehsil and Distt. Bilaspur,H.P.174004
Tel:01978-243581, 94180-58657,98173-
24081
Part-A
17. M/SRajdeep Agri.-Products Pvt.Ltd. 3279/1,Ranjit Nagar,New Delhi-110008
011-25847771, 25847772, Tele Fax-
011-25487773
Part-A
18. M/S Thousand Petals, Poly houses Pvt. Ltd;8/86,Dashbhuja Apartments,Ram Baug Colony, Paud Road,Kothrud, Pune -38
Tel:098231-20381, Mr.Rajesh Edke-097350-36760
Fax:020-25440659
- For Bamboo Models Only
19. M/s Himalayan Flora,Vilayat Cottage,Tutikandi,Shimla-4
Tel:98166-19355 - Part-A
20. M/S CompleteGreen Mouse Solutions Pvt.Ltd.Polt No.D-11,Focal Point,Chanalon,Kurali, District Mohali,Punjab.
Tel:0160-6499254 Fax:0160-2641479
- Part-A
21. M/S Churah Valley ,Fruits,Vegetables and Flowers Growers Society,Bjanjraru, Distt. Chamba,H.P.
Tel:01896-227064 - Part-A
22. M/S Techno Green,9-A,IndustrialArea,Bilaspur,H.P.
Tel:01978-221043(Fax)
- Part-A
23. M/S H.P.Agro Industries Corporation Limited,Ground Floor,Nigam Vihar Complex, Shimla-2
Tel:0177-2623811, Fax-2632811,
2623792
- Part-A
24. M/S Ira Industries, Regd. Off: V& PO-Basal (Chambaghat), Tehsil and District Solan, H.P.-173213
Tel:94180-00303, 94188-78303
- Part-A
25. M/S A-Three Agro tech Pvt. Ltd., 503, Modi heights, Opp. AIR, Ratu Road, Ranchi, Jharkhand-834001
Tel Fax: 0651-228912 [email protected]
Part-A
26. M/S Vij Brothers, Phagwara Road, Hoshiarpur-146001
Tel: 01882-222831 Mob. 98146-67272
Part-A
B. Installation of MI System {inside Poly houses} (Part-B):
1. M/S Harvell Irrigation Pvt. Ltd., SCO 110-111, Sector 8-C, Madhya Marg, Chandigarh-160018
Tel:0172-2788104, 2781947
Fax-2545102
Part-B
2. M/S Harvell Agua India Pvt. Ltd., 301304,Meghdoot,94, Nehru Place, New Delhi-110019
Tel:011-26485365, -26413370
Fax-26464849
Part-B
3. M/S Parixit Industries Ltd.,202,Gupta Arcade,IInd Floor,Plot No.4&5,LSC Sherestha Vihar-Delhi-110092
09910885218 [email protected]
Part-B
4. M/s EPC Industries Ltd, H-109,MIDC Ambad,Nashik-422010-Maharashtra
Tel:0253-2381081,238241
Fax-0253-2382975
[email protected] Part-B
5. M/S Swati Storewell Pvt.Ltd.,44.45,Industrial Area,Sector-1,Parwanoo-173220
Tel:01792-232570,232683
Fax-01792-232770
- Part-B
6. M/S Netafim Irrgations IndiaPvt.Ltd.,Regd.Off:26870,Manjusar,Savli,Distt.Vadodara
097250-14798/79/80,Fax-
0266-7264600
NETAFIM.CO.IN Part-B
7. M/S Shivalik Agro Engineers , Near DAV School,Kather Bye Pass Road,Solan-173213
Tel:01792-221861, 98160-75144,Fax-
01792221859
Part-B
C. Construction of Polyhouses & Installation of MI System(inside Polyhouses) Part A & B: S.No. Name and Address of the
Company Contact/ Fax No. E-mail Remarks
1. M/S Finolex Plasson Industries Ltd.,Plot No.399,Urse,Taluka Maval,Distt. Pune-410506
Tel:02114-237045-46, Fax- 02114-237044
Part-A&B
2. M/S Jain Irrigations Limited
Rgd.Off:Jain Plastic Park,P.O.Box:72,NH No.6,Jalgaon-425001
Tel:0257-2558011 Fax:0257-2258111
[email protected] Part- A&B