7/22/2019 Gibbs cam 2009

1/375

SolidSurfacer

GibbsCAM 2009, v9.3rev 1.4, October 2009

7/22/2019 Gibbs cam 2009

2/375

7/22/2019 Gibbs cam 2009

3/375

Table of Contents

Table of Contents

INTRODUCTION 1

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INTERFACE 5

WorkSpace - Taskbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Palettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Main (Top Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Multiple Body Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Body Bag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Solids Context Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Body Bag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Profiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Display Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Faceting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Machining. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

MODELING 19Introduction to Modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

What is Modeling? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Primitives/Atomic Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Workspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Workgroups and Coordinate Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Boolean Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Recreate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Rebuilding Solids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Modeling Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Surface Modeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Plane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Revolve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Loft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Coons Patch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Sweep Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Sheet from Face. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Trim/Untrim Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Stitch Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7/22/2019 Gibbs cam 2009

4/375

Table of Contents

ii

Unstitch Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Untrim & Extend Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Solid Modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Create Solid Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Sphere . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Cuboid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Extrude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Revolve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Loft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Sweep Solid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Solidify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Advanced Solid Modeling Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Offset/Shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Blending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Unstitch Solid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Draft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Slice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Subtract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Intersect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Separate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Geometry Creation from Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Geometry from Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Know Your History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Body Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Body Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Modifying Recreating & Rebuilding Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Method 1: Create a New Solid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Method 2: Locally Edit an Existing Solid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Method 3: Replace/Swap and Rebuild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Method 4: History, Recreate and Rebuild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Tips and Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

ABOUT MACHINING SOLIDS 63

Introduction to 3-Axis Machining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Gen 3 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Compatibility With Earlier Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Surface Tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Machining Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Stock Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

CONTOUR & ROUGH MACHINING 69

Contouring Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71Using the Profiler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Roughing Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Material Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Machining preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Material Only Pockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

7/22/2019 Gibbs cam 2009

5/375

Table of Contents

ii

Optimizing Material Only for Solids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Solids Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Toolpath Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Toolpath Generation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Create 2D Toolpath. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Limitations of Create 2D Toolpath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Open Sides Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

SURFACING PROCESS 83

Common Surfacing Process Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Depths and Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Cutting Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Lace Cut Options Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Lace Cut Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Stepover Retract Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Toolpath Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Toolpath Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

2 Curve Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99Surface Flow Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Surface Flow Start Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Surface Flow Options Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Intersections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104Notes on Intersections Toolpath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

ADVANCED 3D MACHINING 107

About this Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109What is Different? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

The Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109Processes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Process Tiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Base Process and Dependent Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Toolpath Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Boundaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Facet Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Fixture bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Material Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Curve selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Automatic Fillet Surfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

The Task Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Surfaces Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Toolpath Cut Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Trim to Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Material & Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Basic Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Clearances, Cut Depth & Plunging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

7/22/2019 Gibbs cam 2009

6/375

Table of Contents

iv

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Depth of Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Plunging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Common Process Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Profile Smoothing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Cutting Strategy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Cutting Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Down/Up Mill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120Common Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120Pocketing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123N Curve Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126Curve Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128Contour. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130Constant Stepover Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131Flats Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Intersections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134Intersections - Rest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136Steep Shallow Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142

Toolpath Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144Tool Holder Gouge Checker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Options Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147Entry/Exit Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150

Entry Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151Exit Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152Entry/Exit Trimming Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153Retract Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154

Boundary Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154Boundary Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155Boundary Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156Stock Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

PLUNGE ROUGH PROCESS 161

What is A Plunge Rough Process? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164Controlling Where Plunge Rough Machines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

Uphill Cutting and Gouge Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168PullOffs with Stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Contouring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Guide Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170

MODELING EXERCISES 173

#1: Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175Creating The Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175

Part Set-Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175Lofted Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175Extruded Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177Profile Intersection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178Extracting a Body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178Making the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179

7/22/2019 Gibbs cam 2009

7/375

Table of Contents

v

Modifying the Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180Filleting Corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180Renaming a Body with the Properties Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Replacing a Body in the History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Rebuilding the Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

#2: Hot Punch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Part Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

Extruded Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1833 Profile Loft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Moving Geometry to a Workgroup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Selecting Alignment Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

#3: Teapot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186Opening an IGES File Directly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Controlling Import Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186Auto-Size the Workspace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Creating the Teapot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Revolving the Main Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Sweeping the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189Two Drive Curve Sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Combining the Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Creating a Variable Radius Blend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191Creating the Shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192Unstitching the Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Measuring the Teapot Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Deleting a Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Extracting the Shell from the History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194Slicing with a Plane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194Calculating the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195

#4: Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197Creating the Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

Part Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Aligning a CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Extruding the Slants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200Adding Intersection Blends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

Correcting A Design Flaw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202Recreating the Cross Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203Rebuilding the Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

#5: Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205Creating the Remote Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205

Re-positioning the Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206Applying the Draft Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207

Creating Shutoffs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Combining the Shutoffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209

Creating the Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210Extracting a Parting Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210Creating the Base with the Parting Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211

Creating the Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213Boolean Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

7/22/2019 Gibbs cam 2009

8/375

Table of Contents

vi

MACHINING EXERCISES 215

#1: The Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217The Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217Creating Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .218

#1: Roughing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .218#2-5: Lace Cuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

#6: 2 Curve Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224#7: Surface Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227#8: Edge Intersection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

#2: The Hot Punch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230Part Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

Document Control Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230Tool List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

Creating Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230#1: Contouring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230#2: Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232#3: Engraving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233

#3: Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

Part Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236The Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236Stock Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

Machining The Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238#1-3: Roughing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238#4: Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239#5: Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240#6: Lace Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240#7: Contour with the Profiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .241#8: Corner Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

#4: The Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244Part Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

Positioning the Part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244Tool List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

Machining the Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244#1: Face Mill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244Extracting the Cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245#2: Contour with Profiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246#3: Lace Cut on the Angled Face . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249#4: Roughing the Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250#5: Semi-Finishing the Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251#6: Finishing the Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253#7: The Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254

ADVANCED 3D EXERCISES 257

#1: The Mold Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259Part SetUp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259Roughing the Mold Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259

The Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259Operation 1: Roughing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260Ops 1 & 2: Roughing, Strategy A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263Ops 1 & 2: Roughing Strategy B - Rest Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264Ops 3 & 4: Roughing Strategy C - Bounding Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

7/22/2019 Gibbs cam 2009

9/375

Table of Contents

vi

Ops 5-7: Semi-Finishing Via Flats Cut, Strategy D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267#8-10: Refining Toolpath, Strategy A - Selected Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270#11-13: Refining Toolpath, Strategy B - Silhouette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

Finishing the Mold Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272#14: Finishing and Optimizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272Optimization, Step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274Optimization, Step 2A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

Optimization, Step 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275Optimization, Step 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276Optimization, Step 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278

#2: The Food Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279Part Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279Machining the Mold Core. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279

#1-4: Roughing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279#5-7: Roughing and Finishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283#8: Lace Cut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288#9: Lace Cut on the Long Walls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290#10: Lace Cut Toolpath Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291#11-14: Lace Cut - Radial with Up Machining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

#15: N-Curve Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295#3: The Mold Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

Part Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298Roughing the Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

#1: Roughing the Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298#2-3: Pocketing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303#4: Flats Cut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309#5: Semi-finishing, Using Constant Stepover Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310#6: Semi-finishing, Using Contour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311#7: Semi-finishing, Using Intersections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312#8: Finishing, Using Intersections-Rest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315#9: Finishing, Using Steep Shallow Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317

#10: Finishing, Using Intersections-Rest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318

QUICK EXERCISES 321

Building a Spherical Ellipse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323Step #1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323Step #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324Step #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324

Replace History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325Part Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325

Saved Processes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325Unstitching and Subtracting Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326

Machining the Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Loading Processes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328

Modifying the Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Importing the Changed Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Replacing the Model History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Redoing the Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

2D Contour. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330Model Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330

Solid Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330

7/22/2019 Gibbs cam 2009

10/375

Table of Contents

viii

Base and Stock Bodies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330Creating Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332

Tool List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332# 1-3, Contouring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332# 4, Surfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333

Advanced 3D, Using Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334#1: N-Curve Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334

#2: Curve Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338

APPENDIX 341

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343

PART PRINTS 347

INDEX 355

7/22/2019 Gibbs cam 2009

11/375

INTRODUCTION

7/22/2019 Gibbs cam 2009

12/375

7/22/2019 Gibbs cam 2009

13/375

Introduction

3

CHAPTER 1 : Introduction

ABOUT THIS MANUAL

SolidSurfacer allows users to def ine parts as solid and surface modeling techniques. This manual is composedof two types of sections: reference and tutorial. It is recommended that the user briefly review the referencematerial and then move on to the accompanying exercises.

There are three primary methods of using SolidSurfacer to create machining parts. The first method is bycreating solid models from part blueprints using the solid modeling functions contained in the GibbsCAMThere are many powerful modeling functions including adding, subtracting and intersecting solids, automaticchamfering and f illeting, and several methods for generating solid bodies from geometry.

Secondly, solid file formats generated by other CAD programs can be opened directly in GibbsCAM. Mostformats can be directly opened or imported by the system (some formats require the purchase of an additionaoption).

The final method is by importing 3D surface files. The system recognizes and imports many surface entitiesOnce a surface file is brought into the system it can be solidified, or can be kept as a surface model, andmachined.

Regardless of the method used to define the part, the final model can be machined using the 3D surfacingcapabilities. The standard Roughing and Contouring functions can be applied to solid bodies and surfacesThere is also a Surfacing function that provides several methods for generating 3-axis toolpaths to efficientlycut complex solid and surface part models.

Users should familiarize themselves with the basics of the system outlined in the Geometry Creation manualMill manual and Advanced CS manual before reviewing this manual. This manual assumes a level ofprof iciency with creating geometry, coordinate systems and basic machining.

DEFINITIONSThe terms and definitions provided below are used to describe objects and elements used by the system, andthroughout this manual. More information can be found in the Glossary.

Body: The term body is a generic term that refers to both solids and sheets. A solid body can be thought of asa bowling ball, while a sheet body is more like a balloon with an inf initely thin wall.

Face:A face is one surface of a solid or sheet. A Sheet face includes the positive and negative sides while a solidonly includes the positive side. Faces are surfaces that have knowledge of the surfaces that surround them. For

example, one side of a cube would be considered a face. Each face is bound by loops. A simple face is boundedby one loop.

Surface:A surface is either a face, group of faces (depending on how the surface was created) of a solid or sideof a sheet. Sheets have two surface sides and a solids have only one.

Solid:A solid is a body composed of faces and the area enclosed by the faces. Solids have volume. Solids bodiesare used as the building blocks in creating part models in GibbsCAM. Unlike sheets, solids only have a positiveside.

7/22/2019 Gibbs cam 2009

14/375

Introduction

4

Sheet:A sheet is an surface with two sides, positive and negative. A sheet has no volume or thicknessassociated with it.

Edge:An edge is a curve/line between two faces. An edge of a solid must have exactly two faces connected to it.Note that more than two faces at an edge produces an invalid solid. The edge of a sheet can have a single faceconnected to that.

Loop:A loop is a series of connected edges that outline a face.

Vertex:A vertex is an endpoint of an edge.

TEXT CONVENTIONSIn this and all other GibbsCAM manuals you will find a number of standards used in the text, known asconventions.

Screen text:Any text you see like this is referring to text you will see in GibbsCAM or on your monitor.Typically this is a button or text for a dialog.

Keystrokes: Words that appear like this refer to a keystroke or mouse action, such as right-click orCtrl+C.

Term:Words that you see in bold followed by a colon refer to a word or phrase used in GibbsCAM.

7/22/2019 Gibbs cam 2009

15/375

INTERFACE

7/22/2019 Gibbs cam 2009

16/375

7/22/2019 Gibbs cam 2009

17/375

Interface

7

CHAPTER 2 : InterfaceThis chapter describes interface items that are specific to the system when the SolidSurfacer option isinstalled. The Getting Started, Common Reference, Geometry Creation and Mill manuals contain descriptionsof standard system interface items including theWorkSpace - Taskbar, Palettes, Bodies, Solids Context MenusPreferences and Machining.

WORKSPACE - TASKBARThe Taskbar contains seven items that are part of the SolidSurfacer interface. For more detailed informationon these Taskbar items see the Interface section in the Getting Started manual.

Show Solids: This button will show and hide all bodies, including sheets.

Render/Wireframe: This item toggles through four states from only drawing the edges of bodies to renderingthe solid.

Indicate Sheet Side: Indicate the positive and negative sides of a sheet.

Face Selection: Enable/disable face selection mode.

Edge Selection: Enable/disable edge selection mode.

Profiler: Enable/disable the Profiler grid.

1. Show Solids

2. Render/Wireframe

3. Indicate Sheet Side

4. Face Selection

5. Edge Selection

6. Profiler

7. Pre-Selection Highlighting

Edges only Wireframe bodies Solids with edges Solid body only

Edges only Wireframe bodies Solid body only

7/22/2019 Gibbs cam 2009

18/375

Interface

8

Pre-Selection Highlighting: Pre-Selection Highlighting shows you which face your mouse is currently hoveringover, making face and edge selection easier.

PALETTESModeling is accomplished with palettes. Some of the palette buttons will open a dialog and some will take aspecific action. There are two ways of modeling in GibbsCAM, with the Surfacing Modeling palette or the

Solid Modeling palette. The palettes are accessed from the main (or top level) palette. For more detailedinformation about these items see the Getting Started manual and the Modeling section.

MAIN (TOP LEVEL)Three buttons in the Top level palette are part of the main functionality of SolidSurfacer. The Surface and SolidModeling palettes help to create and modify bodies and the Body Bag is an organizational container forbodies.

MODELINGSheet, or surface, modeling is done through theSurface Modeling palette. Surfaces may be extractedfrom faces or created from geometry. Booleans fromSolid Modeling palette are also used in sheetmodeling. For more information see page 25.

Solid modeling has three palettes, the main Solid Modeling palette and two sub-palettes. One for creatingsimple atomic bodies and another palette for more advanced modeling. For more information see page 31.

BODIESEach body (solid or sheet) contains a written history of how it was created and details about its physical anddisplay properties. Bodies can be hidden and placed in a container called a Body Bag. They may even berendered in wireframe and hidden.

Surface Modeling Solid Modeling Body Bag

7/22/2019 Gibbs cam 2009

19/375

Interface

9

HISTORYThe History list is accessed from the body context menu (seepage 12). It displays the creation tree for any selected body. All of thebodies and functions that were used to create the selected solid orsheet will appear in the History list, even if they are no longer activebodies. The system maintains the history of all bodies that arecreated. Imported models will not have an existing history (they are

essentially atomic bodies).

The History list allows the user to access any body that went into theconstruction of the selected solid. By giving the user access to thehistory of a model, changes can be made to an earlier step in the modeling process, allowing for changes toeasily be incorporated to the f inal model without having to start over from scratch.

All non-atomic bodies have histories which contain information on the parents. Parents is the term used todescribe the solids or sheets that were used to create the selected body. Solids may have one parent as in casesof rounding or slicing, or two parents as in the case of Boolean operations. Bodies removed from theWorkspace as the result of a Boolean operation are maintained in the History list. Bodies contained in theHistory list are considered dormant bodies, while bodies in the workspace and Body Bag are active. Operationssuch as rounding or any of the Boolean functions can be performed on active bodies only.

The History list is structured in a hierarchical format where the selected body is at the top and all other bodiesused to create it are found below in steps or branches. Double-clicking on the icon next to the name of a bodywill make that body active and bring it back into the workspace. In order to make modif ications to a bodycontained in the History list and have those changes incorporated into the existing history, Recreate must beused. Recreate and Rebuild are described in the next section. See page 54 for more information on the Historylist.

7/22/2019 Gibbs cam 2009

20/375

Interface

10

PROPERTIESThe Properties dialog is accessed from the body context menu (see page 12). It contains items that apply to theselected body. The user can change the name of the solid or sheet and enter a comment. The coordinatesystem that the selected solid or sheet was last modified in will be displayed at the top of the dialog.

Solids and sheets can be designated as Part, Fixture or Stock. Additionally there are the Fixture - Display Onlyand Stock - Display Only options. When solids and sheets are created, they will be designated as a Part bydefault unless the setting is changed in this dialog. Solids or sheets designated as a Fixture will be rendered inred and will be used as constraints when creating machining operations. Solids and sheets designated as Stockwill be rendered in dark blue and will be used as the initial stock condition when creating machiningoperations.

Using either of the display only items will display a body as a fixture or stock, and be used in rendering, butwill not be used in the toolpath generation calculation. When any stock or f ixture bodies are present thesystem may attempt to use 3D toolpath rather than 2D in some cases and having potentially hundreds offixture bodies to take into account when generating toolpath can seriously affect system performance. UsingDisplay Only stock and fixtures settings can greatly improve system performance, making this feature very

important for TMS.

This dialog also contains a Chord Height (See Faceting on page 16. for more information) for the faceting ofthe selected solid or sheet. Click the Apply button to change the chord height based on the value entered. Thisvalue will only be applied to the selected solid or sheet.

The Properties dialog can also be used to view bodies. When this dialog is open, different bodies can beselected and the contents of the Properties dialog will change to reflect the new body selected. Bodiescontained in the History list can be viewed in the Properties dialog by selecting the cube icon in the Historylist.

7/22/2019 Gibbs cam 2009

21/375

Interface

1

There is also a Physical Properties section which provides surface area calculations for solids and sheetsvolume calculations for bodies, and surface periphery calculations for sheets. Within the Physical Propertiessection is an Accuracy slide bar and a Calculate button. The Accuracy slide bar designates the amount oprocessing time and effort the system will allocate for the calculations. With the slide bar closer to thenegative end of the spectrum, the calculations will be less accurate and vice versa. It should be noted that allcalculations fall within a certain set range of accuracy regardless of the setting of the accuracy slide bar.

The percentage values do not directly correlate to the calculation, in that a 0% accuracy is still going toprovide a reasonably accurate calculation. The Accuracy setting affects the calculation processing time; asbodies become more complex, the calculation time increases. In those cases, it may be desirable to designate alower accuracy in order to speed up the process. The system will always provide the +/- accuracy tolerance sothat the user can determine whether the calculation is accurate enough for its purposes.

The following are conversion values for taking the volume in cubic inches (as is shown in the Propertiesdialog) to such measurements as ounces and liters.

1 cubic inch = 0.55409 oz.

1 oz. = 29.57353 ml

Multiple Body PropertiesThe Multiple Body Properties dialog

appears when more than one body isselected when the Show Properties ofSelected command is chosen. This dialoghelps to assign properties to many bodies atone time.

Add or change bodies in the dialog bychanging the selection. Quickly set allbodies in the dialog as a Part, Fixture, orStock type as well as their Chord Heightand a Comment. Apply To All must bepressed in order to apply the new settings

to all the bodies in the dialog.

Figure 1: Solid Properties measurements

7/22/2019 Gibbs cam 2009

22/375

Interface

12

BODY BAGThe Body Bag is used to store bodies during part creation in order to organize the Workspace. Double-click a body to move it from the workspace to the Body Bag. Bodies can also be moved with the Body

and Body Bag context menu. Items that are placed in the Body Bag are still considered active as long as theBody Bag is open they can be selected, modified, machined, etc. Bodies in the Body Bag are represented asicons which can be moved, resized and selected.

SOLIDS CONTEXT MENUSMenus accessed by right-clicking on certain items in the system are referred to as context menus. Thefollowing dialogs have context menus that are accessed by right-clicking on the title bars of the dialogs.

BODYThe body context menu is accessed by right-clicking on a body or history entry.

Recreate : The Recreate mode takes the selected body back to its creation action to be modified. The selectedbody is drawn in red and any changes made will permanently replace the selected body. To cancel Recreatemode, right-click a body and choose Exit Recreate or click the red body.

Rebuild : This reprocesses the History list and incorporates any changes made using Recreate, Swap or Replaceinto a new final part model. The Rebuild function is limited in that models cannot be rebuilt if the changesrequire a significant alteration to the topology. For example, if the change created any new edges, the finalmodel cannot be rebuilt.

Show History : The History list displays the creation process of the selected body. All bodies that were used tocreate the selected body will be displayed in the History list. Dormant bodies contained in the History list canbe brought back to the Workspace by double-clicking on the icon in the History list.

Figure 2: Resized Icons in the Body Bag

7/22/2019 Gibbs cam 2009

23/375

Interface

13

Clear History : This clears the history of the selected body, essentially turning the solid into an atomic bodyThis action is not undoable.

Show Properties : This command will open the Properties dialog for a solid or sheet. See Properties onpage 10 for more information.

Show Properties of Selected: This command will open the Properties or Multiple Body Properties window to

show the properties of all currently selected bodies.

Bag It/Un-Bag It : Bag It will place a selected body into the Body Bag. If the body is in the Body Bag, Un-Bag Ititem will place it in the workspace. This function does not work on multiple selections, see Body Bag onpage 15 for multiple selection functions.

Bag/Un-Bag Selected: This command will move all selected bodies into or out of the Body Bag.

Align Face To CS:When Face Selection is active you maychoose a face and align it to the current CS. Thiscommand is accessed by right-clicking on a face. Choosingthis command orients the part to the CS as if the following

steps were taken.

1. Create a new CS from the target CS, i.e. the CS youwant to align to.

2. Select a planar, cylindrical or complex face.

3. Select Align Plane Through & Move (right mousemenu choice) or Alt-click the Align CS button.For a cylinder use Align CS Normal & Move.

4. Apply the Modify CS (XYZ) command to the solid to assign it to the new CS.

5. Select the target CS.

6. Apply the Modify CS (HVD) command to the solid to assign it to the target CS and move it.

7. Delete new CS.

The following items for selecting and deselecting faces are only available when the system is in Face Selectionmode. These options are useful when multiple faces must be selected for modeling or machining functions,and frees the user from having to select one face at a time.

Tangent Faces : This will select/deselect the target face and all of the faces reachable by a tangency.

Faces Above : Neighboring faces will be selected/deselected if they have an upper boundary that lies above theupper boundary of the target face. Next it will branch out to the adjoining faces of the neighboring faces andrepeat the selection/deselection using the neighbors upper boundary as the condition (rather than the targetface). A special condition exists for flat faces that neighbor the target face. They will be selected/deselectedbased on the lower boundary of the target face.

Faces Below : Neighboring faces will be selected/deselected if they have an lower boundary that lies below thelower boundary of the target face. Next it will then use the adjoining faces boundary and repeat the selection/

7/22/2019 Gibbs cam 2009

24/375

Interface

14

deselection. However, adjoining flat faces will be selected/deselected based on the upper boundary of thetarget face.

Floor Faces : Selects/Deselects all floor faces connected to the target face. A floor face is approximately normalto the depth axis of the current CS; the approximation is set by the Floor/Wall Angle Tolerancevalue set in File> Preferences > Interface > Selection.

Wall Faces : The target face will be selected/deselected and any connected face that is parallel to the depth ofthe current CS. Angled walls that fall within the Floor/Wall Angle Tolerance value set in File > Preferences >Interface > Selection will also be selected.

3D Faces : This will select/deselect faces connected to the target face that are not defined as a floor or wall.Next it will branch out to the adjoining faces and select/deselect them using the same logic.

Transition Faces : This will select/deselect all transition faces connected to the target face. A transition face is asmooth blend that is connected to a wall and floor face.

Fillets : Thiswill select/deselect all constant radius fillet faces that are connected to the target face. The targetface will also become selected. The system will only select fillets that have the same constant radius as the

target face if the target face is a fillet).

EDGERight-click a selected edge to access options that affect edge selection. When an edge isdouble-clicked, the system tries to build a closed loop of edges starting with the selectededge. The 2D Chain and 3D Chain options affect how the system chooses the next edgeto be connected at each vertex.

2D Chain :When this option is selected, double-clicking an edge will attempt to select a loop of edges thatare planar to the current CS (or those closest to it), therefore resulting in a 2D loop. If there is more thanone possible choice for an edge at a vertex, the system chooses the one that is closest to the same direction.

3D Chain :When this option is selected, double-clicking an edge will attempt to select a loop of edges thatare normal to the current CS (or those closest to it), therefore resulting in a 3D loop.

HISTORYThe context menu, accessed from the title bar of the History list,contains the items Expand All and Collapse All. The Expand Allitem will expand the tree, displaying all branches which containthe bodies used to create the selected model. Collapse All willnot show any branches and only the selected model icon willappear at the top of the History list.

7/22/2019 Gibbs cam 2009

25/375

Interface

15

BODY BAGThe context menu contains the items Clean Up Body Bag, Resize All Icons, BagSelected, Un-Bag Selected, Snap to Grid, Select Body Bag, Select Workspace,Deselect Body Bag and Deselect Workspace. The Clean Up Body Bag item willreorganize the Body Bag icons so that all icons can be viewed and none overlap.The Resize All Icons item allows the user to modify the size of the Body Bagicons. This item is active when an icon is selected in the Body Bag. When this

item is selected, a box that can be dragged and resized will be drawn around theselected icon. All the icons in the Body Bag will be resized accordingly. The BagSelected item places any solids or sheets that are selected in the drawingwindow into the Body Bag. The Un-Bag Selected item will take any selectedBody Bag icons and place the solids/sheets back into the drawing window fromthe Body Bag. The Snap to Grid item can either be checked on or off. When on,Body Bag icons that are moved will snap to a grid for alignment. The Select/Deselect Body Bag items selects/deselects all the bodies in the Body Bag, and the Select/Deselect Workspace items selects/deselects all entities(including bodies and geometry) in the Workspace. These last few items are very useful when analyzingsurface files by providing a method for isolating problem areas.

PROFILERAccess the Prof ilers context menu by right-clicking on any visible part of the Profiler grid.

Profiler Depth : Select this option to access the Profiler Depth dialog. The Depthf ield shows the grids absolute depth; drag the grid while this dialog is open and the

field will update itself to reflect the current depth. The user may specify a newdepth by entering the value in the field and clicking Apply.

Select All Profiles : This option selects all profiles generated by the Profiler grid.Note that selected prof iles turn blue.

Select Faces From Selected Profiles : This option selects all faces that are tangent to the profiles generated bythe Profiler grid. When a profile has been selected for machining, this option will only select the faces that aretangent to the toolpath, or the portion of the prof ile between the start and end machining markers.

Select Faces Inside Selected Profiles: This option selects all faces that are contained fully within the boundary ofthe selected profile and that are not tangent to the profile. The depth of the face is not a factor, i.e. any face

within the boundary will be selected regardless of its depth.

PREFERENCES Display Tab on page 16

Faceting on page 16

7/22/2019 Gibbs cam 2009

26/375

Interface

16

DISPLAY TABSoftware preferences are accessed from the File > Preferences menu. The Preferences are discussed in detail inthe Common Reference Guide. This section has focused discussion on several items that pertain directly toSolidSurfacer. Several items found in the Display tab affect the graphic display of solids and sheets.

Wire Drawing: Solids and sheets can be displayed as renderedsolid objects or as wireframe drawings. The Render/Wireframe button in the Task Bar determines whether solidsand sheets will be rendered objects or wireframe drawings.This setting lets you determine whether the system displaysedges or facets of solids or sheets depending on the selectionmade in the Wire Drawing section.

Chord Height: The overall part chord height is entered in thehere. The chord height determines the faceting resolutionwhen solids and sheets are rendered. Click the Apply buttonto finalize the change to the faceting tolerance for selectedbodies, as well as setting the value for new bodies to becreated in the future. See the Faceting section for more information on how Chord Height is set and used.

FACETINGRendering is the process of displaying a picture of a model on the screen. When bodies are rendered, they arefaceted. Facets are small planar surfaces that compose the rendered model. The more facets drawn, the closerthe model resembles the actual mathematical model and the more time it takes for the system to render themodel. Faceting affects the quality of the rendered bodies. It also affects overall system performance and speed.The faceting chord height should be set at a value that balances the quality of the model with system

7/22/2019 Gibbs cam 2009

27/375

Interface

17

performance. The faceting tolerance has NO effect on machining tolerances, only on the rendered image onthe screen.The tolerance used for surface machining is set locally in the Process dialogs Solids tab > AdvancedSettings dialog and is labeled as the Cutting Tolerance and globally in the Document Control dialog as UseGlobal settings for Solids > Part Rough Tolerance. It is this specification which designates how closely thetoolpath will follow the surface.

The number of facets used to render a model is determined by the chord height. A chord is a straight line that

joins any two points on an arc or circle. The chord height is the distance from the chord to the arc or circle(Figure 3). The smaller the chord height, the closer the facet will be to the arc or circle, resulting in a betterrendered image of the solid or sheet (this is a 2D description of chord height; the system uses a 3D chordheight for the faceting of solids and sheets, but the general idea is the same).

The system uses a global faceting chord height which is applied to the entire part model. The global chord

height will be applied to all solids and sheets that are created or imported. The global chord height is enteredin the Display tab which is accessed from the File > Preferences menu. A number can be entered in the textbox or the slider can change the value by moving it left and right.

A different faceting chord height can be applied to individual solids and sheets. The Properties dialogaccessed by right-clicking on a solid or sheet, contains a chord height value which will only be used to facetthe selected solid or sheet. See Properties on page 10 for more information.

MACHININGSolidSurfacer has two machining processes, Surfacing and Advanced 3D. Both processes are for machiningsolids.

1. Chord Height

Figure 3: Chord Height

1. Surfacing

2. Advanced 3D

3. Plunge Rough

7/22/2019 Gibbs cam 2009

28/375

Interface

18

Surfacing: The Surfacing process creates 3Dtoolpath from solids and surfaces. For moreinformation see The Surfacing process isused to create full 3 Axis toolpaths.Combining the Surfacing process tile with atool tile will create a Surfacing process. Thesystem supports surfacing with flat, bullnose

and ball endmills. Solids or sheets must beselected as the cut shape for surfacingprocesses. The Surfacing dialog containsthree sub-windows, Surfs., Options, andToolpath which are accessed via tabs at thetop of the dialog. The specifications in eachof these dialogs change depending on thetype of toolpath selected for the process. Thesix surfacing options are Lace Cut, 2 CurveFlow, Surface Flow Cut, Intersection-Edges,Intersections-Faces, and Intersections-Auto.The items in this section that are not

described in this section are described in theMill or Advanced CS manuals. on page 85.

Advanced 3D: This is another process that creates 3D toolpath from solids and surfaces. Additionally, Advanced3D creates H.S.M. (High Speed Machining) compatible toolpath. For more information see the SurfacingProcess section.

7/22/2019 Gibbs cam 2009

29/375

MODELING

7/22/2019 Gibbs cam 2009

30/375

7/22/2019 Gibbs cam 2009

31/375

Modeling

2

CHAPTER 3 : Modeling Introduction to Modeling on page 21

Modeling Reference on page 25

Know Your History on page 54

Modifying Recreating & Rebuilding Bodies on page 55

Tips and Techniques on page 60

INTRODUCTION TO MODELING What is Modeling? on page 21

Solids on page 22

Sheets on page 22

Primitives/Atomic Solids on page 22

Workspace on page 23

Workgroups and Coordinate Systems on page 23

Boolean Operations on page 23

Recreate Mode on page 24

Rebuilding Solids on page 25

WHAT IS MODELING?Modeling is the process of def ining a parts shape and dimensions on a computer. Common types of modelinginclude geometric modeling (both 2D and 3D), solid modeling, and surface modeling.

Geometric modeling is the process of defining a model with simple geometric constructions such as pointslines, circles and splines. Geometry can be def ined in either two- or three-dimensional space.

Solid modeling is the process of defining a part as a solid object rather than as geometry or a collection ofsheets. The process begins with the creation of a simple solid known as an atomic or primitive body. Boolean

operations can then be performed on an atomic body to create a new, distinct body. Advanced techniquessuch as shelling, offsetting, blending, stitching/unstitching, and drafting may then be used to create the finapart model.

Surface modeling is the process of creating sheets as the foundation for a model. Boolean operations can alsobe performed on sheets. The surface creation tools are primarily intended to be used with surface f iles that areimported rather than for creating complete part models using surface modeling techniques. The use of solidmodeling tools is the recommended method for modeling a part.

7/22/2019 Gibbs cam 2009

32/375

Modeling

22

SOLIDSA solid is an object that has volume. Solids can either be single bodies (lumps) or a collection of bodies (multi-lump body). Solids can either be viewed as wireframe drawings or rendered objects; however, only the lattercan be selected to perform modeling functions.

Solids are rendered in grey; however, selecting a solid changes it to a yellow body. Solids may also be definedas stock (blue) or a fixture (red). Selecting a body will show if it is composed of lumps or if it is a multi-lump

body. Models containing lumps or multi-lump solids can be separated to create multiple bodies.

SHEETSSheets do not have any thickness or volume. A sheet has knowledge of the neighboring sheets that surroundit. Sheets may have either one face or several faces. Similar to solids, sheets may also be defined as a part,stock, or fixture.

When surface f iles are imported, each surface entity is brought in as a single sheet (unless the Solidify optionis chosen). These sheets can either be machined directly or modif ied as necessary to complete the part model.

PRIMITIVES/ATOMIC SOLIDSA primitive or atomic solid is a simple, non-divisible solida solid that is not built from other solids. Atomicsolids do not have a history (or branches). All solid models originate from at least one atomic solid. Examplesof an atomic solid include a sphere, a cube and a revolved/lofted/swept/extruded 2D shape.

Atomic solids are created using the options in the Create Solid palette which is accessed by clicking on theCreate Solid button in the Solid Modeling palette. The solidifying functions, which convert sheets to solids,are also contained in the Create Solid palette. Solidified sheets are considered atomic solids as they have nohistory associated with them.

Sphere:A ball shaped solid.

Cuboid:Any type of rectangular solid.

Extrude:A two dimensional closed shape extruded along the depth axis.

Revolve:A 2D shape, either open or closed, revolved around either the horizontal or vertical axis by a specifiednumber of degrees.

Loft: Lofted solids are created by selecting a series of closed shapes that will be blended together using selectedalignment points. Lofting is also referred to as skinning or blending.

Sweep: Swept solids are created by selecting base curve geometry and drive curve geometry. The base curveacts as the spine which determines the overall contour of the sweep and the drive curve(s) designate thelocation and shape of the solid.