geo pressure systems inc. downhole instrumentation … 3 purchase guide downhole gauges downhole...
TRANSCRIPT
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
OFFSHOREPLATFORM
HORIZONTALCOMPLETION
OBSERVATIONWELLS
FLUID LEVEL CONTROL
FOR DOWNHOLE PUMPS
SAGDHI-TEMP
INSTALLATIONSERVICES
GEO Pressure Systems Inc.
Downhole Instrumentation
Product Guide2015 –Edition 1
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
2015 Product Guide Index
Product IndexPurchase Guide 3
Hardware Selection Guide 6
Gauges 8
PCP System-01 4–20 mA Downhole Pressure Sensor (IECEx Certified) 9
PCP System-02 Digital Pressure and Temperature Sensor 11
Quartz System-02 Hybrid Quartz Permanent Downhole Pressure Gauge 14
Vibrating Wire System-02 250°C Piezometer with Easy Connect Cablehead System 17
Slimhole System-02 0.5” Downhole Pressure and Temperature Sensor 20
PCP System-03 Digital Pressure, Temperature, and Vibration Sensor 22
PCP System-07 Advanced Downhole Artificial Lift Monitoring System 25
PCP System 12 Advanced Downhole PCP Monitoring System 29
Downhole Bubble Tube Pressure Data Collection System 33
Gauge Carriers 45
Fortified Gauge Carrier for Artificial Lift 46
Welded Internal Sensing Downhole Instrumentation Carrier 48
Unibody Downhole Sensor Mandrel 50
Downhole Instrumentation Cables 52
150°C (302°F) Downhole Instrumentation Cable 53
200°C (392°F) Downhole Instrumentation Cable 55
285°C (545°F) Thermocouples 57
300°C (572°F) Four-Conductor Downhole Instrumentation Cable 61
Cable Protectors 63
Downhole Centralizer Clamp 64
Heavy-Duty Cable Protectors 65
Light-Duty Cable Protectors 67
Splices 69
4 mm (0.160”) Pressure-Testable Easy Connect Downhole Instrumentation Cable Splice (Patent Pending) 70
Pressure-Testable Easy Connect Downhole Instrumentation Cable Y Splice (Patent Pending) 72
Wellhead Pressure Control 74
Wellhead Feed-Through 75
Surface Electronics 77
G6 Downhole Gauge Controller 78
Generic Data Acquisition System 79
Generic Solar RTU Cabinet 80
Accessories 82
4–20 mA Surface Pressure Gauges 83
Downhole Instrumentation Installation Equipment 85
Page 3
Purchase Guide
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Purchase Guide
WHY GEO PSI?
A Purchase Decision Guideline
GEO PSI is incredibly passionate about downhole instrumentation. Our company is
carefully crafted to deliver successful results and provide our customers with exceptional
value. We are also 100% dedicated towards a future when it’s feasible that every wellbore
will have a permanent downhole gauge installation.
Our formula for success:
Deliverability
ReliableHardware
CompleteProduct Line
CustomerService InnovationInstallation
& Training
Knowledge
AccountabilityBest Value
Competitive pricing due to vertical integration & volume manufacturing
( D I V I D E D B Y )
Reliable HardwareReliable and proven hardware is the cornerstone to our success.
The founders of GEO PSI have been manufacturing and
installing downhole instrumentation for more than 20 years. Our
downhole sensors, instrumentation cables, cable protectors,
and surface electronics are designed, manufactured, quality
controlled and tested to withstand the test of time in challenging
wellbore conditions including: deep horizontal completions,
offshore jack-up rigs, high temperature, and aggressive artificial
lift deployments. That is why our corporate trademark is
RELIABILITY – JOB 1™.
KnowledgeWe know what we are talking about. The entire senior
management group has field experience and technical expertise.
We understand completions and are capable of providing expert
advice on how to successfully deploy various types of downhole
instrumentation systems. Our expertise includes Completion
Analysis, Instrumentation Requirement Assessment, Logistics,
Project Management, and Data Integration. We only recommend
solutions that we know will work.
Installation & TrainingIt’s not enough to just provide great hardware. GEO PSI
also owns Perm Services, a Canadian based downhole
instrumentation service company. Perm Services installs more
than 120 downhole instrumentation systems per year for various
Canadian energy companies. More importantly, Perm Services
provides our international customers and trading partners with
unparalleled field service and support options. Our solution
is truly turnkey. Unlike any other manufacturer, GEO PSI can
utilize Perm Services to install downhole instrumentation
systems in any country and/or provide training and support.
We offer complete installation equipment packages comprised
of pneumatic spoolers, specialty air tools, and hand tools
associated with installation services.
Page 4
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Purchase Guide
DeliverabilityEveryone wants a supplier that they can
count on. Many companies focus on running
lean or just in time inventory systems which
may be practical for many manufactured
products. GEO PSI has taken a completely
opposite approach, by being heavily invested
in finished goods inventory and a scalable
manufacturing process. We know the oil
patch. Our customers need us to provide
equipment for opportunities with short
notice and they need a company that can
fulfill the requirements of large tenders. It’s
not unusual for us to have several hundred
downhole sensors, 200,000+ feet of
instrumentation cable, and more than 5,000
cable protectors in stock. In 2014, GEO PSI
has manufactured more than 1,300 downhole
sensors and 2.1 million feet of downhole
instrumentation cable.
Customer ServiceWe understand your needs! Our manufacturing facility is staffed 7 days a week. There is always
someone on call to provide support and help when you need it.
InnovationGEO PSI invests heavily into research and development. Our engineering team has
brought forward several ideas that have improved downhole instrumentation reliability
and functionality. Some of them include:
» Easy Connect™ Cablehead System. The cablehead is a mechanical component
that connects the downhole gauge to the instrumentation cable. It has long
been the weak point and commonly known as the leading cause of system
failures. The engineers at GEO PSI have developed a patent pending cablehead
that simplifies makeup in the field and greatly reduces system failures.
» 0.160” Instrumentation Cable. GEO PSI invented a stainless steel downhole assembly
instrumentation cable with a 0.160” diameter with a wall thickness greater than most
0.25” cables. The unique form is excellent for suspended application and permits
exiting the wellbore out of a casing wing valve, saving the customer both time and
money. In addition, when encapsulated with plastic bumper material, the 0.160”
offers superior crush resistance, compared to most formats of 0.25” cable.
» Artificial Lift Gauge Mounting System. Many downhole instrumentation companies
struggle to successfully instrument high horsepower ESP and PC Pump systems.
GEO PSI has developed a simple and cost effective gauge carrier that absorbs
the vibration and shock, reducing the chance of premature system failure. The
GEO PSI gauge carrier is a non-welded design, ensuring that there is no
electrolysis which may cause premature holes in the production tubing.
One-Stop Manufacturing
Page 5
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for Success
INTERNATIONALGEO PRESSURE
INTERNATIONAL
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE
SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Complete Product LineGEO PSI has products and solutions that covers most of the market segments for
downhole instrumentation products.
DEPLOYMENT OPTIONSTubing Conveyed Systems Cemented In Systems
Suspended Systems Artificial Lift Systems
Multi Gauge Systems Hi Temperature Systems (500°C)
Deep Horizontal Systems High Pressure Systems
Intrinsically Safe Deployments
(Mining)
SENSOR TECHNOLOGIESPiezo-Resistive Sensors Analog 4-20 mA Sensors
Quartz Sensors Downhole Thermocouples
High Temp Piezometers Bubble Tube
OTHER ACCESSORIESQuartz Memory Tools Cable Protectors
Wireless EM Tools Installation Tools & Spoolers
Wireless Inclination Tool Centralizers
SURFACE SOLUTIONSSolar Panel Operated Systems SCADA / DCS Connectivity
Wireless Data Transmission VFD Integration
Vertical Integration and Reasonable PricingGEO PSI is the most vertically integrated downhole instrumentation
supplier in the world. We are the only company in the world that
makes all of the critical components required for a downhole
instrumentation system. We eliminate unnecessary middlemen and
pass savings onto our customers. Additionally, all overseas freight can
be consolidated.
AccountabilityAccountability means being responsible.
Responsibility is being in charge of delivering a satisfactory outcome.
For a company to be truly responsible for successful downhole
instrumentation installations, it must offer a complete solution. This
is where GEO PSI differs from any other downhole instrumentation
company.
Purchase Guide
Page 6
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Hardware Selection Guide Conventional Pressure and Temperature Permanent Downhole Gauge Systems
PUMP CONTROL LAND BASED SYSTEMS OFFSHORE MARKET
» Fluid level monitoring for pump control
» Reservoir presssure control for sand protection
» Production optimization
» Well performance
» Pump performance monitoring
» Reduced workovers
» Reservoir monitoring and drainage efficiency
» Increased production
» Increased ultimate reservoir recovery
» Interference testing
» Transient analysis
» History matching
» Reservoir monitoring and drainage efficiency
» Increased production
» Increased ultimate reservoir recovery
» Interference testing
» Transient analysis
» History matching
» Minimum acceptable standard is for the permanent downhole gauge run to be as long as the workover cycle of the downhole pump
» The system should be re-deployable
» System must be engineered to withstand downhole forces exerted by pumps
» O&G emphasize system reliability and data quality
» Reservoir pressures are typically medium to high
» Completions are complicated
» Permanent downhole gauge equipment must be engineered for performance
» O&G emphasize system reliability and data quality
» Reservoir pressures are typically medium to high
» Completions are complicated
» Permanent downhole gauge equipment must be engineered for performance
$ $$ $$$
PURPOSE OF PERMANENT GAUGE SYSTEM
RETURN ON EQUIPMENT INVESTMENT IS MEASURED BY
TYPICAL SYSTEM COST
Hardware Selection Guide
Page 7
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Hardware Selection Guide Conventional Pressure and Temperature Permanent Downhole Gauge Systems
» Dominiated by 4-20 mA equipment. Cost effective and does not require expensive surface interfaces. Gauge data interfaces directly with vfd’s, loggers, and plc equipment.
» Typically single or multi digital piezo resistive or quartz gauges. Reservoir temperatures may be higher. Emphasis is on transient analysis.
» Dominated by single or multi quartz gauges. Reservoir pressure and temperatures are often extreme. Pressure accuracy and low drift is of utmost importance.
» Simple & cost effective. Most gauges are set to measure annular pressure.
» Ranging from simple & cost effective to premium internal sensing unibody mandrel. May need to be field pressure testable.
» Premium internal sensing pressure testible unibody mandrels.
» Frequently mandrels require exotic threads.
» Bare stainless steel to encapsualted cable for additional shock protection, depending on completion and pump dynamics.
» Bare stainless steel to encapsualted cable for additional shock protection, depending on completion.
» Completions are usually horizontal. Encapsulated cable is required.
» Depending on completion, will range from banding, light duty collar protectors to heavy duty protectors.
» Light duty cable protectors for vertical completions or heavy duty carbon steel protectors for horizontal completions.
» Typically completions are horizontal. Heavy duty carbon steel or stainless steel protectors are utilized.
» Typical data accuracy: 0.16% fs
» Resolution: +/- 0.5 psi
» Drift: Less than 3 psi per year
» Typical data accuracy: > 0.05% fs
» Resolution: +/- 0.005 psi
» Drift: Less than 3 psi per year
» Typical data accuracy: > 0.015% fs
» Resolution: +/- 0.0006 psi
» Drift: Less than 0.02% per year.
TYPE OF GAUGE
DETAILS
GAUGE MANDREL
DOWNHOLE INSTRUMENTATION CABLE
CABLE PROTECTORS
PUMP CONTROL LAND BASED SYSTEMS OFFSHORE MARKET
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Gauges
Gauges
Page 9Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
PRODUCT DEVELOPMENT BACKGROUNDThe GEO PSI IECEx certified
4-20 mA pressure gauge is the first
cost effective solution designed for
measuring Real-Time Pump Intake
Pressure for Artificial Lift systems in
oil and gas wells. The gauge is able
withstand vibrational forces exerted
by high horsepower Progressive
Cavity and ESP Pumps.
The 4-20 mA gauge is engineered
to connect to metal armored cables
(TEC) and utilizes metal-to-metal
sealing techniques. The gauge
body is welded and requires no
elastomers. Ingress protection is
provided by a high pressure glass
feed-thru system and dielectric
grease chamber. The innovative
Easy Connect1 cablehead system
reduces installation errors and
improves system reliability.
» Reliable » Cost Effective » Easy to Install
(1) Patent pending
Permanent Downhole Gauge A cost-effective downhole sensor designed
to accurately measure real-time pump intake
pressure or fluid level.
FEATURES » Patent pending Easy Connect integrated pressure
testable cablehead design allows direct connection to downhole instrumentation cables using metal-to-metal sealing technology.
» Tough 316L stainless steel construction ensures that this tool can be deployed in hostile environments within the oil and gas industry.
» Leak proof design. No primarily elastomer seals. Gauge body components and sensor are welded design.
» Sensor uses a high-pressure feed-through that creates a hermetic seal, protecting its electronics in the event of a cable breach.
» Designed to endure vibration and shock associated with various artificial lift systems.
» Intrinsically safe when connected properly to surface power source.
» International Electro-technical Commission System for Certified Standards related to equipment for use in explosive atmospheres (IECEx Certified).
» No surface electronics required. The direct output of the sensor is 4–20 mA and can connect directly into SCADA, Distributed control system, Loggers, or most variable frequency drives.
PCP System-01 4–20 mA Downhole Pressure Sensor (IECEx Certified)
Certificate No: IECEx QPS 14.0010x
REAL TIME DATA APPLICATIONS » Pump Intake Pressure
Measurement
» Fluid Level Measurement
» Bottomhole Pressure
» Artificial Lift Optimization
» Hydrology
» Observation Wells
» Suspended Deployments
» Tubing Conveyed
Stainless Steel Armored and Encapsulated Downhole Instrumentation Cable (TEC)
Easy Connect Cablehead
Pressure Testable Design
Metal-to-Metal Primary & Secondary Sealing Section
PCP System-01 4–20 mA Downhole Pressure Sensor (IECEx Certified)
Page 10
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
IECEx Certified
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop ManufacturingSPECIFICATIONS & CERTIFICATIONS
Output 4-20 mA
Input voltage range 8-30 VDC
Available pressure ranges 50, 300, 500, 1000, 1500, 2000, 3000 psi
Proof pressure 6,000 psi
Temperature range -40°C to 105°C (-40°F to 221°F)
Accuracy ± 0.1% full scale error best straight line fit
Typical average error(¹) +/- 0.16% full scale
(5 point verification at 20°C)
Long Term Vibration Resiliency 8g at 100 Hz measured peak-to-peak(2)
Compatible TEC cables 0.160˝ / 4 mm single conductor
Construction material Stainless steel 316L
Outside diameter 0.95˝ / 24.13 mm
Length 7.75˝ / 196.85 mm measured from process connection to
top of pressure testable cablehead
Certifications IECEx Ex ia IIB T3 Ga(3) intrinsically safe
Tamb = -20°C to 105°C (-4°F to 221°F)
Applicable Standards IEC 60079-0: 2007-10
IEC 60079-11: 2006
(1) Average error is calculated from a sample batch of 100 units. All errors are expressed as a positive value to
calculate the average. Maximum allowable single error is ± 0.5% absolute full-scale. (2) 14-day bench test. (3) Proof
of certification is available at www.IECEX.com. (4) 3,000 psi model is not IECEx certified.
ORDERING INFORMATION
Pressure Rating Product Number
50 psi 101505
200 psi 101503
300 psi 101504
500 psi 101417
1,000 psi 101418
1,500 psi 100128
2,000 psi 101419
3,000 psi(4) 100126
Cablehead rebuild kit 101468
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
PCP System-01 4–20 mA Downhole Pressure Sensor (IECEx Certified)
Certificate No: IECEx QPS 14.0010x
One-Stop Manufacturing
Page 11Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
PCP System-02Digital Pressure and Temperature Sensor for Permanent Downhole Monitoring
High-Quality Digital Data with Reliable Performance
ARTIFICIAL LIFT OPTIMIZATION AND HIGH-QUALITY BOTTOMHOLE DATA FOR RESERVOIR ENGINEERINGFOR ARTIFICIAL LIFT SYSTEMS AND OBSERVATION WELLS THAT REQUIRE PREMIUM DATA QUALITY
» Patent pending integrated Easy Connect pressure testable cablehead design allows direct connection to downhole instrumentation cable using metal-to-metal sealing technology.
» Constructed out of 316L stainless steel or Inconel 718.
» Sensor uses a high-pressure glass feed-through that creates a hermetic seal, protecting it in the event of a cable breach.
» Fully welded construction ensures maximum protection against gas and fluid invasion.
» Multi-gauge. Up to 8 gauges can be connected to a single downhole tubing encapsulated cable (TEC).
» Serial numbers are transmitted to the surface ensuring the correctly calibration profiles are being utilized.
PRODUCT SUMMARY » Provides a reliable means of collecting high-quality,
real-time downhole pressure and temperature data.
» Direct and simple hookup to pump controllers, loggers, supervisory control and data acquisition (SCADA) systems, programmable logic controllers (PLCs), and variable speed drives (VSDs).
» Eliminates the need for expensive proprietary surface equipment.
QUALITY ASSURANCE » Each gauge is tested to International
Electro-technical Commission (IEC) 801-4 standards for electrical fast transient/burst up to 4,000 volts, which may suppress damage from lightning strikes.
» ISO certified manufacturing.
Easy Connect cablehead1
(1) Patent pending
Pressure-testable design
Metal-to-metal primary and secondary sealing section
Applications• Reservoir analysis
(transient-pressure analysis)
• Fluid level control
(pump intake pressure)
• VSD control
• Artificial lift optimization
• Multi-zone observation wells
PCP System-02 Digital Pressure and Temperature Sensor
Page 12
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
PCP System-02Digital Pressure and Temperature Sensor for Permanent Downhole Monitoring
One-Stop Manufacturing
G6 Downhole Gauge Controller » Decodes downhole telemetry and converts
both, pressure and temperature data to
4-20 mA and/or RS485 Modbus protocol.
Full downhole gauge diagnostic information
can be transmitted through RS485.
» Class 1, Div 2 (Group C&D) certified.
» Compatible with any PLC, VFD, or Surface Logger,
Memory Module, Display, Satellite, SCADA,
Radio Telemetry available on the market.
» DIN rail mounting bracket is available.
» Very low power consumption ensures
maximum performance for Solar Power
Installation in Remote Locations.
» Includes SCADA resettable limit counter and watch
dog timers. Under voltage detection for solar.
Controls power to radio. Optional status lights.
» Multi-gauge. 1 to 8 quartz and/or piezoresistive
sensors can be controlled by a single G6.
G6 Downhole Telemetry Decoder
Page 13
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
TECHNICAL SPECIFICATIONS Sensor type Piezoresistive
Signal output RS485 or 4–20 mA
Input voltage 9–24 VDC
Downhole telemetry Digital Phase Shift-Key
Pressure accuracy ± 0.05% full scale
Pressure accuracy measured
in psi for 1,000 psi sensor
± 0.5 psi
Pressure resolution 0.0003% full scale
Pressure drift < 3 psi per year
Temperature rating 150°C (302°F)
Temperature accuracy ± 0.5°C
Temperature resolution 0.01ºC at 1 Second
Outside diameter 0.875” / 2.222 cm
Overall length 8.10” / 20.57 cm (including cablehead)
Construction material SS 316L or Inconel 718
Real-time sample rate 10 times per sec or slower
Long term vibration resiliency 8g at 120 Hz
(equivalent to 150 horse power PCP)
Available pressure ranges 300 psi*
1,000 psi *
1,500 psi
3,000 psi
5,000 psi
6,000 psi*
10,000 psi
15,000 psi*
Meets or exceeds the
following standards
IEC 801-4
*Special order only. Dimensions of tool may change.
PCP System-02Digital Pressure and Temperature Sensor for Permanent Downhole Monitoring
ORDERING INFORMATION
Product Part Number
300 psi 100772
1,500 psi 100426
3,000 psi 100562
5,000 psi 100697
10,000 psi 100815
15,000 psi 101731
Cablehead rebuild kit 101468
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
G6 100299
Multi-gauge G6 101950
DIN rail bracket 101293
Wireless G6 100954
Option Inconel body available
upon request
One-Stop Manufacturing
Page 14Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
The absolute best resolution, accuracy for pressure and temperature.Downhole pressure temperature sensor,
temperature equipped with a “Quartzdyne”
transducer; the defecto standard for downhole
precision pressure equipment.
» GEO PSI only utilizes Quartzdyne pressure transducers equipped with HYBRID sensor circuitry.
» Quartzdyne’s hybrid circuits, techniques, equipment, and dedication to excellence delivers,on average, a product that increases circuit life dramatically compared to surface mount technologies.
» Hybrid circuits are ideal for high temperature,
rugged conditions, and long life applications.
PRODUCT SUMMARY » When data quality and system reliability
matter the most, GEO PSI’s continuous downhole quartz tool is the best choice!
» 100% Metal to Metal seals; no primary elastomers.
» Hermetically sealed through E-Beam and Ultra-High Vacuum TIG welding contruction process.
» Inconel 718 material is available for corrosive conditions.
» Patent pending integrated dual sealing Easy Connect cablehead system. Permits rig floor pressure test.
» Multi-gauge. Up to 8 gauges can be connected to a single tubular encapsulated cable (TEC).
» Serial numbers are transmitted to the surface ensuring the correctly calibration profiles are being utilized.
TECHNICAL SPECIFICATIONSOutput PSK Telemetry
Input voltage range 8-30 VDC
Current Less than 20mA
Pressure range 10K psi to 20K psi
(68,950 to 137,895 kpa)
Pressure accuracy ± 0.015% full scale
Pressure resolution >0.006 (psi)/second
Pressure repeatability >0.01% full scale
Pressure drift 0.02% (full scale)/year
Temperature range -40°C (-40°F) to +150°C (302°F)
Temperature accuracy ±0.15°C
Temperature resolution 0.005°C/second
Temperature repeatability ±0.01°C
Temperature drift <0.1°C per year
Construction material SS316L or Inconel 718
Length 21”
Outside diameter 0.875” (22.225 mm)
Sample intervals Every 0.10 seconds or slower
Surface communications Modbus RS485 and
4-20 mA output
Example of Hybrid Circuit
Quartz System-02Continuous Downhole Quartz Pressure Temperature Sensor
Applications• The ideal solution when
resolution and pressure
accuracy matters the most.
• Interference testing.
• Reservoir evaluation.
• Multi-gauge
observation wells.
Quartz System-02 Hybrid Quartz Permanent Downhole Pressure Gauge
Page 15
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
» Chamber is purged, greatly reducing long term deterioration of surface mount board
» Hermetically sealed high pressure glass feed-thru
» E-Beam welding
Quartz System-02Continuous Downhole Quartz Pressure Temperature Sensor
» Integrated field pressure test port
» Metal-to-metal seals
» Front and back ferrules
One-Stop Manufacturing
Only 21” long lncluding cable head
21 inches long
Pressure test port
Dual sealing cablehead
Page 16
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for Success
INTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
G6 Downhole Gauge Controller » Decodes downhole telemetry and converts both,
pressure and temperature data to 4-20 mA and/or RS485 Modbus protocol. Full downhole gauge diagnostic information can be transmitted through RS485.
» Class 1, Div 2 (Group C&D) certified.
» Compatible with any PLC, VFD, or Surface Logger, Memory Module, Display, Satellite, SCADA, Radio Telemetry available on the market.
» DIN rail mounting bracket is available.
» Very low power consumption ensures maximum performance for Solar Power Installation in Remote Locations.
» Includes SCADA resettable limit counter and watch dog timers. Under voltage detection for solar. Controls power to radio. Optional status lights.
» Multi-gauge. 1 to 8 quartz and/or piezoresistive sensors can be controlled by a single G6.
G6 Downhole Telemetry Decoder
Quartz System-02Continuous Downhole Quartz Pressure Temperature Sensor
ORDERING INFORMATION
Pressure Material 4 mm (0.160”) TEC 6.35 mm (0.25”) TEC
10,000 psi SS 316L 100113 101788
10,000 psi Inconel 101791 101789
16,000 psi SS 316L 100114 100115
16,000 psi Inconel 100116 100112
20,000 psi Inconel PLEASE CALL PLEASE CALL
Cablehead rebuild kit 101468
Gauge test kit with process connection 101082
Basic gauge cablehead test kit 101553
G6 100299
Multi-gauge G6 101950
DIN rail bracket 101293
Wireless G6 100954
One-Stop Manufacturing
Page 17Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Vibrating Wire System-02250°C Piezometer (Vibrating Wire) with Easy Connect Cablehead System
250°C high-temperature piezometer with pressure and temperature measurement for SAGD
observation wells. With GEO PSI’s exclusive patent pending Easy Connect cablehead system and
4 mm extreme high-temperature instrumentation cable.
PRODUCT DESCRIPTION » Designed for high-temperature
applications such as SAGD,
EOR and geothermal wells.
» GEO PSI 4 mm/0.160”
stainless steel instrumentation
cable is MICA free and
rated to 285°C/545°F
» The dual-barrier Easy Connect
cablehead system greatly
reduces the chance of installer
error. A pressure-test can be
performed before deployment.
» GEO PSI is unparalleled
in product quality and
customer service.
High Temperature PerformanceGeokon’s 4500HT series high-temperature piezometers and pressure
transducers are designed for monitoring downhole pressures and
temperatures in oil recovery systems and geothermal applications.
These sensors are capable of operation under extreme conditions and at
temperatures up to 250°C/482°F. In thermal recovery applications (SAGD
or CSS), they can provide accurate, real-time, continuous monitoring of
pressures in production and injection wells, thereby optimizing the recovery
rate and reducing the costs of the steam injection process. In geothermal
and observational applications, they offer a means for in situ and continuous
monitoring of pressure and temperature over extended periods of time.
Dual sealing metal-to-metal
Pressure testable cablehead
Vibrating Wire System-02 250°C Piezometer with Easy Connect Cablehead System
Page 18
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
TECHNICAL SPECIFICATIONS
Pressure ranges 700 kPa
1, 2, 3, 5, 7.5, 10, 25, 50, 100, 150 MPa
Over pressure limit 2 x rated pressure
Resolution 0.025% full scale
Accuracy ± 0.1% full scale
Linearity < 0.5% full scale
Temperature range 0°C to +250°C (32°F to 482 °F)
Diaphragm displacement < 0.0001 cm³ at full scale
Length x diameter 14.83” (376 mm) x 0.875” (22.25 mm) for 7.5 MPa and less
16” (406 mm) x 1.000” (25.4 mm) for 10 MPa and higher
Process connection ½”—13UNC female
Vibrating Wire System-02250°C Piezometer (Vibrating Wire) with Easy Connect Cablehead System
1
2
3
4
EASY CONNECT1 ADVANTAGECablehead failure is the number one cause for
permanent downhole gauge failures. GEO PSI has
created an innovative system that greatly improves
cablehead success.
1. Plug and play. The factory brazes a high-temperature,
four-pin male connector to the instrumentation
cable, which fits inside a matching female socket.
2. Metal-to-metal sealing front and back ferrules are
attached and secured in place with a hex nut.
3. A secondary cablehead is attached, which has an
additional set of metal-to-metal sealing ferrules.
4. Pressure test port allows GEO PSI to conduct
a pressure test on the primary connection.(1) Patent pending.
Page 19
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Vibrating Wire System-02250°C Piezometer (Vibrating Wire) with Easy Connect Cablehead System
ORDERING INFORMATION
Product Part Number
700 kPa / 100 psi 100783
1,000 kPa / 150 psi 100784
2,000 kPa / 300 psi 100785
3,000 kPa / 450 psi 100786
5,000 kPa / 750 psi 100787
7,500 kPa / 1,100 psi 100788
10,000 kPa / 1,500 psi 100789
25,000 kPa / 3,700 psi PLEASE CALL
50,000 kPa / 7,400 psi PLEASE CALL
100,000 kPa / 14,800 psi PLEASE CALL
140,000 kPa / 20,000 psi PLEASE CALL
Cablehead rebuild kit 101468
One-Stop Manufacturing
Page 20Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Artificial Lift Optimization & High Quality Bottomhole Data for Reservoir EngineeringProvides a reliable means of collecting high quality real-time downhole
pressure and temperature. Direct and simple hook up to pump
controllers, loggers, SCADA, PLC’s and variable speed drives.
Eliminates the need for expensive proprietary surface equipment.
FEATURES » Patent pending Easy Connect cablehead system allows for
metal-to-metal connection to downhole cable.
» Constructed out of 316L Stainless Steel or Inconel 718.
» Sensor utilizes a high pressure glass feed-thru that creates a hermetic seal to protect the sensor in the event of a cable breach.
» Fully welded construction ensures maximum protection against gas and fluid invasion.
» Multi-gauge telemetry with up to eight sensors can be installed on a single cable.
» Frequency based bottomhole transmission of serial number ensures calibration cannot be mixed.
Each gauge is tested to
International Electro-technical
Commission (IEC) 801-4
standards for electrical fast
transient/burst up to 4,000 volts,
which may suppress damage
from lightning strikes.
Slimhole System-020.5” Downhole Pressure and Temperature Sensor
Easy Connect! Cablehead
Width: 0.5”
Length: 8.25”
(1) Patent pending
Applications• Slim hole completion
• Coil tubing
• Reservoir Analysis (Pressure
Transient Analysis)
• Fluid Level Control (Pump Intake
Pressure)
• VFD Control
• Artificial lift optimization
• Multi gauge observation wells
Slimhole System-02 0.5” Downhole Pressure and Temperature Sensor
Page 21
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
ORDERING INFORMATION
Product Part Number
1,000 psi 101554
3,000 psi 101555
6.000 psi 101556
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
G6 100299
Multi-gauge G6 101950
DIN rail bracket 101293
Wireless G6 100954
Optional Inconel body available
upon request
Slimhole System-020.5” Downhole Pressure and Temperature Sensor
TECHNICAL SPECIFICATIONSSensor type Piezoresistive
Signal output RS485 or 4-20 mA
Input voltage 9-24V DC
Downhole telemetry Digital Phase Shift Key
Pressure accuracy ± 0.05% full scale
Pressure accuracy measured in psi
for 1,000 psi sensor
± 0.5 psi
Pressure resolution 0.0003% full scale
Pressure drift < 3 psi per year
Temperature rating 150°C
Temperature accuracy ± 0.5°C
Temperature resolution 0.01ºC at 1 Second
Outside diameter 0.5” / 12.7 mm
Overall length 8.25” / 209.55 mm (including cablehead)
Construction material SS 316L
Real time sample rate 10 times per second and slower
Available pressure ranges 1,000 psi
6,000 psi
3,000 psi
Meets or exceeds the following
standards
IEC 801-4
One-Stop Manufacturing
Page 22Last Revised: 150828
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
PCP System-03Digital Pressure, Temperature, and Vibration Sensor for Permanent Downhole Monitoring
ARTIFICIAL LIFT OPTIMIZATIONFOR ARTIFICIAL LIFT SYSTEMS THAT REQUIRE PREMIUM DATA QUALITY
FEATURES » Patent pending integrated Easy Connect cablehead design
allows direct connection to downhole instrumentation cables using metal-to-metal sealing technology.
» Dual-barrier cablehead system permits rig floor pressure testing.
» Constructed out of 316L stainless steel or Inconel 718.
» Sensor uses a high-pressure glass feed-through that creates a hermetic seal, protecting it in the event of a cable breach.
» Fully welded construction ensures maximum protection against gas and fluid invasion.
PRODUCT SUMMARY » Provides a reliable means of collecting high-quality, real-time
downhole pressure, temperature, and frequency-based downhole pump vibration data. Vibration data sample speed is quick enough to generate a Fourier transform plots with vibration data from 0 to 600 hertz.
» Direct and simple hookup to pump controllers, loggers, supervisory control and data acquisition (SCADA) systems, programmable logic controllers (PLCs), and variable speed drives (VSDs).
» Eliminates the need for expensive proprietary surface equipment.
QUALITY ASSURANCE » Each gauge is tested to International
Electro-technical Commission (IEC) 801-4 standards for electrical fast transient/burst up to 4,000 volts, which may suppress damage from lightning strikes.
» ISO certified manufacturing.
Easy Connect cablehead1
Pressure testable design
Metal-to-metal primary and secondary sealing section
x + z vibration
High-Quality Digital Data with Reliable Performance
Applications• Artificial lift optimization
• Downhole vibration harmonics
• Fourier transform analysis
• Reservoir analysis
(pressure-transient analysis)
• Fluid level control
(pump intake pressure)
• VSD control
(1) Patent pending
PCP System-03 Digital Pressure, Temperature, and Vibration Sensor
Page 23
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
PCP System-03Digital Pressure, Temperature, and Vibration Sensor for Permanent Downhole Monitoring
G6 Downhole Gauge Controller » Decodes downhole telemetry and converts
both, pressure and temperature data to
4-20 mA and/or RS485 Modbus protocol.
Full downhole gauge diagnostic information
can be transmitted through RS485.
» Class 1, Div 2 (Group C&D) certified.
» Compatible with any PLC, VFD, or Surface Logger,
Memory Module, Display, Satellite, SCADA,
Radio Telemetry available on the market.
» DIN rail mounting bracket is available.
» Very low power consumption ensures
maximum performance for Solar Power
Installation in Remote Locations.
» Includes SCADA resettable limit counter and watch
dog timers. Under voltage detection for solar.
Controls power to radio. Optional status lights.
G6 Downhole Telemetry Decoder
The purpose of this gauge is to provide energy companies with an understanding of downhole vibration harmonics with the goal of increasing artificial lift longevity and reducing workovers.
Fourier transform plot at 100 RPM (PCP completion)X Vibration Z Vibration
Page 24
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
One-Stop Manufacturing
TECHNICAL SPECIFICATIONSSensor type Piezoresistive
Signal output RS485 or 4–20 mA
Input voltage 9–24 VDC
Downhole telemetry Digital Phase Shift Key (PSK)
Pressure accuracy ± 0.05% full scale
Pressure accuracy measured
in psi for 1,000 psi sensor
± 0.5 psi
Pressure resolution 0.0003% full scale
Pressure drift < 3 psi per year
Temperature rating 150°C / 302°F
Temperature accuracy ± 0.5°C
Temperature resolution 0.01°C at 1 sec
Outside diameter 0.875” / 22.225 mm
Overall length 8.10” / 205.74 mm (including cablehead)
Construction material SS 316L or Inconel 718
Real-time sample rate 1 sample per second or less
1,300 vibration samples per second(1)
Vibration sensor range ± 8 g
Vibration resolution ± 0.002 g
Available pressure ranges 300 psi* 1,500 psi 5,000 psi 10,000 psi
1,000 psi* 3,000 psi 6,000 psi* 15,000 psi*
Meets or exceeds the
following standards
IEC 801-4
* Special order only. Dimensions of tool may change. (1) Call GEO PSI for additional details.
PCP System-03Digital Pressure, Temperature, and Vibration Sensor for Permanent Downhole Monitoring
ORDERING INFORMATION
Product Part Number
300 psi PLEASE CALL
1,000 psi PLEASE CALL
1,500 psi 101585
3,000 psi 100951
5,000 psi PLEASE CALL
6,000 psi PLEASE CALL
10,000 psi PLEASE CALL
15,000 psi PLEASE CALL
Cablehead rebuild kit 101468
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
G6 100299
DIN rail bracket 101293
Wireless G6 100954
Optional Inconel body available
upon request
One-Stop Manufacturing
Page 25Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
PCP System-07 Advanced Downhole Artificial Lift Monitoring System
The PCP-07 exemplifies GEO PSI’s relentless commitment to downhole reliability
and development of downhole instrumentation features that help our customers
increase production and reduce workovers.
GEO PSI gauges have a mechanical engineering advantage that improves long-term performance
and data quality while simplifying the installation process.
GAUGE SYSTEM MEASUREMENTS DATA APPLICATION
Pump intake pressure and temperature
Monitoring wellbore fluid level. Can be used to prevent pumping-off and to reduce sanding-off. Useful for preventing gas production through the stator. Reservoir engineers can perform transient pressure analyses.
Pump discharge pressure Real-time operator access to downhole pump performance and stator/rotor deterioration. Can be used for emergency shutdown to preserve PCP pump life.
Pump discharge temperature
Monitoring elastomer wear. An increase to pump discharge temperature provides insight into elastomer issues.
X and Z vibration Early observation of abnormal pump performance caused by mechanical failure, gas, or solid production through the tubing.
7-in-1 Measurements
1. Pump intake pressure
2. Pump intake temperature
3. Pump discharge pressure
4. Pump discharge temperature
5. X vibration
6. Z vibration
7. Surface casing pressure
PCP System-07 Advanced Downhole Artificial Lift Monitoring System
Page 26
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
PCP System-07 Advanced Downhole Artificial Lift Monitoring System
Easy Connect CableheadVibration Sensor Electronics Section
Pressure-Testable Cablehead
Intake Pressure Sensor
Metal-to-Metal Autoclave
Sealing
Features Advantages BenefitsHigh Quality Bottomhole Data Improved accuracy and resolution results in
better insightRESULTS
Designed for aggressive PC Pumps Able to withstand high vibration RELIABILITY
Easy Connect Pressure Testable Cablehead System1
Tool can be pressure tested on the rig floor before being deployed downhole
RELIABILITY
100% Metal-to-Metal Sealing System Leak proof and safe from fluid invasion RELIABILITY
Hermetically sealed E-Beam Weld Construction
Improved pressure integrity RELIABILITY
Field Testable discharge pressure mandrel port
Gauge carrier is pressure testable before deployment
RELIABILITY
Fast Telemetry 1/2 second sampling rate
Important factor for vibration, torsion, and downhole speed accuracy
RESULTS
316L Stainless Steel Body Corrosion Resistant and suitable for moderate H2S and CO2
RELIABILITY
GEO PSI exclusive shock mount vibration dampening technology
Protects the electronics and extends tool operational life
RELIABILITY
Compact, Easy to Use Surface Interface
Simple to use touchscreen interface. Easily connects to SCADA & VSD’s.
RESULTS
ISO 9001:2008, ISO 14000:2004, OHSAS 18001:2007 Certification
Improved quality, service, and on time delivery. Right the first time!
RESULTS
(1) Patent pending
Discharge Pressure Sensor
Page 27
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Optional GEO PSI Data Acquisition SystemsThe most important aspect of downhole monitoring is integrating data into
our customer’s network and control systems.
AT GEO PSI WE BELIEVE IN USER-FRIENDLY TECHNOLOGICAL SOLUTIONSOur cabinet has a color touchscreen logger that is intuitive and easy to
operate. Furthermore we can connect easily to any SCADA, DCS, or
Variable Speed Drive through RS485, RS232, Ethernet, and other available
systems. Our data acquisition system is expandable and can easily connect
to virtually any other surface instrumentation. Examples include pressure
gauges, flow meters, actuators, and tank storage level equipment.
We focus on delivering practical and reliable solutions with excellent workmanship.
All GEO PSI cabinets are CSA/UL Approved for either hazardous or general
purpose locations.
Outside View of NEMA 4X Cabinet
Inside View of Cabinet Color Touchscreen Logger
KEY FEATURES: » 12” x 16” small, compact, and
elegant enclosure
» 3.5” color touchscreen display
» Intuitive interface with on-screen instruction manual
» 32 GB onboard memory
» RS485, RS232, and Ethernet outputs
» Expandable for additional surface instrumentation inputs
» Safe operating temperature of -50°C to +75°C (-58°F to 167°F)
» CSA/UL-approved enclosure
OTHER CAPABILITIES » Topography analysis
» SCADA radio programming
» Factory acceptance testing
» Intrusion alert notification
PCP System-07 Advanced Downhole Artificial Lift Monitoring System
Page 28
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
TECHNICAL SPECIFICATIONS
Output Phase Shift-Key (PSK) telemetry with
embedded frequency encoding
Input voltage range 9-24 Volts DC
Available pressure
ranges
300 psi* 1,000 psi* 1,500 psi
3,000 psi 5,000 psi 6,000 psi*
10,000 psi
Temperature rating 150°C/302°F
Pressure accuracy ± 0.05% Full Scale
Pressure resolution 0.01 PSI
Temperature accuracy ±1°C
Vibration sensors and
resolution data
36 g range
0.034 g resolution
Dimensions Length 14 7/8” (200.02 mm) x Width 2 1/8” (53.975 mm) x
Depth 7/8” (22.225 mm)
Transducer type Piezoresistive
Mechanical body Stainless steel 316
Process connections Female autoclave
Sample speed Two samples per second for pressure and temperature
* Special order only
PCP System-07 Advanced Downhole Artificial Lift Monitoring System
ORDERING INFORMATION
Product Part Number
300 psi PLEASE CALL
1,000 psi PLEASE CALL
1,500 psi PLEASE CALL
3,000 psi PLEASE CALL
5,000 psi 102001
6,000 psi 101999
10,000 psi 101998
Cablehead rebuild kit
(3 required)
101468
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
G6 100299
DIN rail bracket 101293
Wireless G6 100954
Optional Inconel body available.
Different calibration ranges for intake and
discharge pressure is available.
One-Stop Manufacturing
Page 29Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
PCP System-12 Advanced Downhole PCP Monitoring System
The PCP-12 exemplifies GEO PSI’s relentless commitment to downhole reliability
and development of downhole instrumentation features that help our customers
increase production and reduce workovers
GEO PSI gauges have a mechanical engineering advantage that improves long-term performance
and data quality while simplifying the installation process.
GAUGE SYSTEM MEASUREMENTS DATA APPLICATION
Pump intake pressure and temperature
Monitoring wellbore fluid level. Can be used to prevent pumping-off and to reduce sanding-off. Useful for preventing gas production through the stator. Reservoir engineers can perform transient pressure analyses.
Pump discharge pressure Real-time operator access to downhole pressure performance and stator/rotor deterioration. Can be used for emergency shutdown to preserve PCP pump life.
Pump discharge temperature
Monitoring elastomer wear. An increase to pump discharge temperature provides insight into elastomer issues.
X and Z vibration Early observation of abnormal pump performance caused by mechanical failure, gas, or solid production through the tubing.
12-in-1 Measurements
1. Pump intake pressure
2. Pump intake temperature
3. Pump discharge pressure
4. Pump discharge temperature
5. X vibration
6. Z vibration
7. Downhole rod speed
8. Surface rod speed
9. Downhole rod torsion
10. Rotor positioning
11. Surface casing pressure
12. Accumulated pump rotation count
PCP System 12 Advanced Downhole PCP Monitoring System
Page 30
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
PCP System-12 Advanced Downhole PCP Monitoring System
Easy Connect CableheadVibration Sensor Electronics Section
Pressure-Testable Cablehead
Intake Pressure Sensor
Metal-to-Metal Autoclave
Sealing
Features Advantages BenefitsHigh Quality Bottomhole Data Improved accuracy and resolution results in
better insightRESULTS
Designed for aggressive PC Pumps Able to withstand high vibration RELIABILITY
Easy Connect Pressure Testable Cablehead System1
Tool can be pressure tested on the rig floor before being deployed downhole
RELIABILITY
100% Metal-to-Metal Sealing System Leak proof and safe from fluid invasion RELIABILITY
Hermetically sealed E-Beam Weld Construction
Improved pressure integrity RELIABILITY
Field Testable discharge pressure mandrel port
Gauge carrier is pressure testable before deployment
RELIABILITY
Fast Telemetry 1/2 second sampling rate
Important factor for vibration, torsion, and downhole speed accuracy
RESULTS
316L Stainless Steel Body Corrosion Resistant and suitable for moderate H2S and CO2
RELIABILITY
GEO PSI exclusive shock mount vibration dampening technology
Protects the electronics and extends tool operational life
RELIABILITY
Compact, Easy to Use Surface Interface
Simple to use touchscreen interface. Easily connects to SCADA & VSD’s.
RESULTS
ISO 9001:2008, ISO 14000:2004, OHSAS 18001:2007 Certification
Improved quality, service, and on time delivery. Right the first time!
RESULTS
(1) Patent pending.
Discharge Pressure Sensor
Page 31
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
GEO PSI Data Acquisition SystemsThe most important aspect of downhole monitoring is integrating data into
our customers’ network and control systems.
AT GEO PSI WE BELIEVE IN USER-FRIENDLY TECHNOLOGICAL SOLUTIONSGEO PSI’s cabinet has a color touchscreen logger that is intuitive and easy
to operate. Furthermore, we can connect easily to any SCADA system,
Distributed Control System (DSC), or VSD through RS485, RS232, Ethernet,
and other available systems. Our data acquisition system is expandable
and can easily connect to virtually any surface instrumentation, including
pressure gauges, flow meters, actuators, and tank storage-level equipment.
All of GEO PSI cabinets are CSA/UL approved for either hazardous or
general-purpose locations.
GEO PSI focuses on delivering practical and reliable solutions with excellent workmanship.
Outside View of NEMA 4X Cabinet
Inside View of Cabinet Color Touchscreen Logger
KEY FEATURES: » 12” x 16” small, compact, and
elegant enclosure
» 3.5” color touchscreen display
» Intuitive interface with on-screen instruction manual
» 32 GB onboard memory
» RS485, RS232, Ethernet outputs
» Expandable for additional surface instrumentation inputs
» Safe operating temperature of -50°C to +75°C (122°F to 167°F)
» CSA/UL-approved enclosure
OTHER CAPABILITIES » Topography analysis
» SCADA radio programming
» Factory acceptance testing
» Intrusion alert notification
PCP System-12 Advanced Downhole PCP Monitoring System
Page 32
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
TECHNICAL SPECIFICATIONSOutput Phase Shift-Key (PSK) telemetry with
embedded frequency encoding
Input voltage range 9-24 Volts DC
Available pressure ranges 300 psi* 1,000 psi* 1,500 psi
3,000 psi 5,000 psi 6,000 psi*
10,000 psi
Temperature rating 150°C/302°F
Pressure accuracy ± 0.05% Full Scale
Pressure resolution 0.01 PSI
Temperature accuracy ±1°C
Vibration sensors and
resolution data
36 g range
0.034 g resolution
Dimensions Length 14 7/8” (200.02 mm) x Width 2 1/8” (53.975 mm) x
Depth 7/8” (22.225 mm)
Transducer type Piezoresistive
Magnometer 24-bit resolution
Mechanical body Stainless steel 316
Process connections Female autoclave
Sample speed Two samples per second for pressure and temperature
Up to 1,200 rpm for downhole and surface rod
rotation speed
* Special order only
PCP System-12 Advanced Downhole PCP Monitoring System
ORDERING INFORMATION
Product Part Number
300 psi PLEASE CALL
1,000 psi PLEASE CALL
1,500 psi PLEASE CALL
3,000 psi 101805
5,000 psi PLEASE CALL
6,000 psi 101624
Cablehead rebuild kit
(3 required)
100468
Gauge test kit with
process connection
101082
Basic gauge
cablehead test kit
101553
G6 100299
DIN rail bracket 101293
Wireless G6 100954
Optional Inconel body available upon
request
Different calibration ranges for intake and
discharge pressure is available.
One-Stop Manufacturing
Page 33
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Downhole Bubble Tube Pressure Data Collection System with Distributed Downhole Temperature Data via Thermocouple Technology
WORKS FOR TEMPERATURES UP TO 1,150°C / 2,102°F
Downhole Bubble Tube Pressure Data Collection System
Page 34
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Bubble Tube Pressure Collection Theory
The primary advantages of bubble tube pressure collection systems are system reliability and cost-effectivenessThe concept is very simple. An automated system controls pressurized inert gas such as nitrogen or helium, which
is injected down a capillary tube into a pressure chamber or fluid into the wellbore causing a purge. An automated
solenoid valve is then closed. The reservoir pressure fights back, compressing the inert gas column in the capillary
tube. A high-end piezo-resistive transducer measures the compressed pressure at surface and the GEO PSI logger
makes an accurate downhole calculation of the reservoir pressure.
CHAMBER CONDITION PRIOR TO PURGE
GEO PSI actively installs bubble tube systems in the Canadian steam-assisted gravity drainage (SAGD) environment
with a 100% success track record (as of July 2006).
SURFACE PRESSUREMONITORING EQUIPMENT
SURFACE WELLBOREGAS PRESSURE
WELLBORE HYDROSTATICFLUID PRESSURE
COMPRESSED GAS PRESSURE IN SYSTEM TO MONITOR BOTTOMHOLE
PRESSURE
INER
T PU
RGE
GAS
SU
PPLY
SOLENOID VALVE AND TRANSDUCER
DOWNHOLE
Page 35
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
AFTER THE GAS HAS EQUALIZED WITH THE BHP, GAS INJECTION IS STOPPED.
Bubble tube systems are very low maintenance. GEO
PSI engineers each solution so that the inert gas
supply only needs recharging every 1 to 3 months.
In some cases, supplied natural gas can be substituted
for nitrogen or helium.
Although bubble tube technology has been used for
BHP calculations for more than 75 years, its overall
reliability and cost-effectiveness has kept it relevant
to this day. Currently, bubble tube technology is
commonly deployed in SAGD, high-temperature
offshore fields in Southeast Asia, geo-thermal energy
completions, and enhanced oil recovery systems using
steam floods across the world.
Pressure Performance Statistics » Accuracy ± 0.15% full scale (standard)
» Resolution 16-bit Analog to Digital (A–D) processing
» Drift < 0.1% full scale per year
Bubble Tube Pressure Collection Theory
SURFACE PRESSUREMONITORING EQUIPMENT
SURFACE WELLBOREGAS PRESSURE
WELLBORE HYDROSTATICFLUID PRESSURE
COMPRESSED GAS PRESSURE IN SYSTEM
TO MONITOR BHP
INER
T PU
RGE
GAS
SU
PPLY
SOLENOID VALVEAND TRANSDUCER
DOWNHOLE
Page 36
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
GEO PSI goes above and beyond the status
quo to engineer innovative products that deliver
reliabiabily and highly durable instumentation to
our customers. This is accomplished by placing
a considerable portion of our R&D budget and
engineering time towards high-temperature
downhold instrumentation solutions.
A distinct advantage that GEO PSI has over our
competition is that we manufacture our own
downhole instrumentation cable, commonly
referred to as tubular encapsualted cable
(TEC). TEC is the most common package for
downhole instrumentation and is manufactured
by a cold-formed tube mill.
The TEC manufacturing process begins with
a stainless steel strip, which is continuously
formed into a tube through a progressive
series of rollers. The thermocouple conductors
are injected into the tube. After welding, the
tube is further reduced until it reaches the
final diameter. Product quality is automatically
and manually monitored during the entire
manufacturing process.
Using Thermocouples for Downhole Temperature Measurement
GEO PSI tube mill
Rollers forming tube
Inventory at our Calgary location
Inventory of Thermocouple Instrumentation CableFor temperatures greater than 300°C/572°F, we
use mineral insulated cables (MICA).
Page 37
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Breakthrough—Improved Reliability for Downhole ThermocouplesGEO PSI has developed an exclusive manufacturing
process that has greatly increased thermocouple
reliability for use in downhole SAGD applications. This
has been accomplished by strategically eliminating the
weak points of conventional thermocouple systems.
Thermocouples are extremely sensitive to corrosion, and
it’s extremely difficult to consistently make corrosion-
proof joints. Most downhole thermocouple systems rely
on silver brazing to attach thermocouples to a stainless
steel instrumentation line.
GEO PSI has invented a manufacturing process
that hermetically seals thermocouples inside the
instrumentation line, effectively protecting them from
oxidation and other forms of contamination.
Redundancy. GEO PSI installs a redundant
thermocouple at each measurement point. This
is beneficial for result verification. Alternatively,
thermocouple sensors can be spaced apart inside
the same cable for measuring temperature at different
well depths.
Pump-Down System Advantage. Because GEO PSI’s
thermocouples are not externally attached, there is no
change to the outside diameter of the instrumentation
cable. This is beneficial when deploying pump-down
bundles in coiled tubing deployments because more
measurement points can fit in smaller-diameter coiled
tubing strings.
Filler/Safe-Handling Section. Thermocouples are
typically installed in bundles or attached to strength
membrane for pump-down purposes. To avoid damage
from handling or banding, GEO PSI has developed a
1–2 m (4–6 ft) safe handling section at the end of our
instrumentation cable, greatly reducing wear and tear
while pulling instrumentation bundles through
coiled tubing.
Mineral Insulated Cable Assembly (MICA)-Free
Cables. While MICA insulation offers excellent
temperature ratings, it is susceptible to moisture
wicking and can be difficult to use in the field, especially
when creating reliable surface terminations. Excessive
humidity can lead to sensor failures, and MICA insulation
is difficult to strip and terminate. GEO PSI thermocouple
systems use a special form of perflouorokoxy (PFA) as
insulation, which has a safe operating temperature of
nearly 300°C/572°F. It’s extremely easy to work with in
the field. No soft leads are required at the termination,
making our solution more cost-effective and quicker
to deploy.
Improved Tensile Strength and Crush Resistance.
GEO PSI downhole thermocouples have an outside
diameter of 4 mm (0.160”) with a wall thickness of
0.762 mm (0.030”). Other downhole thermocouples
have an outside diameter of 3.175 mm (0.125”) with only
0.584 mm (0.023”) wall thickness. GEO PSI cables have
the advantage of greater tensile strength and
crush resistance.
Downhole Thermocouple Success 300°C/572°F
Splice-Free DesignGEO PSI thermocouple cables can be manufactured up to 5,000 m / 16,404 ft in length
Page 38
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
TYPE K DUAL THERMOCOUPLE SPECIFICATIONSTemperature range: -40°C to 285°C (-40°F to 545°F)
Temperature Accuracy: < ±2.2°C (35.96°F)
Repeatability: < ±0.1°C (32.18°F), depending on logger
Stability: Excellent
Resolution: 16-bit analog digital
Time Constant: 1 sec
Construction material: Stainless steel 316L
Size/Dimensions: Thermocouple housing (0.015 mm (3/8”) outside diameter; 0.108 mm (2 3/4”) length)
Vibration: Excellent
Shock: Excellent
Pressure rating: 10,000 psi
TUBE WIRE SPECIFICATIONSVALUE
Metal jacket Material Stainless steel 316L
Outside diameter 4 mm/0.160”(1)
Wall thickness 0.76 mm/0.030”
Surface finish Hardness 34.8 HRC @ RHC(2)
Seam Gas tungsten arc weld
Weld quality Eddy inspection (3)
Insulation Material PFA
Diameter 2.46 mm/0.097”
Long Term Operating Temperature 285°C/545°F
Short Term Maximum Temperature(4) 300°C/572°F
Color Red & Yellow
Core Alumel x 2 (RED INSULATION)
Chromel x 2 (YELLOW INSULATION)
4 x 24 AWG stranded(5)
Conductor DC resistance
Return Loop (Red + Yellow)
1,532 Ω/1,000 ft at 20°C/68°F
Armor DC resistance 22.5 Ω/1,000 ft
Operating voltage 1 VDC
Mechanical Weight 0.051 lb/ft
External pressure rating 20,000 psi
Breaking tension 2,140 lbs
Yield tension 1,300 lbs
Crush 33,450 lbf over 1”
Yield tension 1,300 lbs
Crush 33,450 lbf over 1”
NOTES: (1) Reference Specification: ASTM A636, (2) HRC/RHC: Rockwell Hardness measured in C-Scale, (3) Reference Specification: ASTM E426. (4) Cannot exceed 300°C. Please call GEO PSI for more information. (5) American Wire Gauge.
PRODUCT SUMMARYFour-Wire Thermocouple sensors
provide the most robust and reliable
solution for high temperature
measurement in SAGD reservoirs.
285°C/545°F 4 mm/0.157” outside diameter four-conductor cable with Swagelok fitting and dual TYPE K thermocouples.
285°C/545°F Dual Thermocouple Downhole Instrumentation Cable
APPLICATIONS• Single point and
distributed temperature
monitoring
• Coiled Tubing
Instrumentation Bundles
SERVICES AVAILABLE• Technical support
• Installation and setup
• Maintenance
5840m to End Lot No 45456a5asAD-001 5840m to End 5840m to End Lot No 45456a5asAD-001 5840m to End 5840m to End Lot No 45456a5asAD-001 5840m to End
Page 39
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Surface Solutions
GEO PSI designs and manufactures surface solutions that are SAFE, Certified, Reliable, Easy-to-Use, Easy-to-Service, and Integrate into SCADA or DCS Control Systems.INTELLIGENT MODULAR DESIGN—Each cabinet is
fit for purpose and manufactured in quantity to reduce
end costs to customers. Interchangeable spare units
are available for rapid field repairs. The function of each
cabinet is clearly labeled and can be configured to
accommodate various installation scenarios.
SAFE—All units are CSA-approved for either general-
purpose areas or hazardous environments. Only National
Electrical Manufacturers Association (NEMA) 4-certified
enclosures are used.
The thermocouple input box is
typically installed approximately
3m from the wellhead and
attached to a cement pole or
cable tray. Analog signals are
converted to digital RS485
near the source. With this
design, we create a convenient
disconnect point, making
pull and re-run operations
smoother and more efficient.Toe purge box Heel purge box
Wellsite thermocouple input boxDownhole data programmable logic
controller (PLC) bubble tube controller SCADA/DCS interface box
Page 40
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Heel or Toe Purge Boxes
KEY FEATURES » CSA certified for general-purpose or hazardous areas
» Compatible with nitrogen, helium, or supplied gas
» Automatic PLC-controlled purge with three manual command purge options—Local Push Button, PLC Touchscreen, or Remote RS485 Register Command
» Nominally closed solenoid safe for hazardous area deployment
» Nitrogen/supplied gas filter with sticker advising of service maintenance date
» High-end piezoresistive surface pressure gauge.
» Includes wiring label diagram.
WORKMANSHIP DETAIL » All wiring has ferrules. All terminals are labeled
and cross identified with the wiring diagram.
» Factory acceptance testing is conducted before field deployment.
» Only high-quality compression ferrule fittings are used.
CSA general-purpose nitrogen model pictured
Page 41
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
KEY FEATURES » CSA certified for general-
purpose or hazardous areas
» Bubble tube control system and thermocouple quarterbacked by a readily available colour touchscreen Horner PLC
» Intuitive local control menus
» All inputs in 16-bit A–D resolution
» Expandable—Single PLC can control up to 120 analog inputs and multiple bubble tube control systems
» PLC cold rated to -50°C / 122°F
» 32 GB onboard historical data memory
» Optional battery backup system available
» Easy to integrate into SCADA and DCS environments via RS485, RS232, wireless radios, cell modems, fibre optics, or TCP/IP
WORKMANSHIP DETAIL » Factory acceptance testing
is conducted before field deployment.
» Spare fuses and an instruction manual are included.
» System offers complete turnkey integration with customer control systems.
» We include 24x7x365 support.
Surface Electronics Data Acquisition Box
HMI display of Surface Logger
All inputs are clearly labelled.
Page 42
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
» CSA approval sticker for general-purpose or hazardous area approval
» Scaleable amount of 16-bit analog isolated channel thermocouple input cards
» Receives power and communicates data to the surface unit via 14/4 Teck cable
The thermocouple input box is typically installed approximately
3 m from the wellhead and attached to a cement pole or cable
tray. Analog signals are converted to digital RS485 near the
source. Enough spare downhole thermocouple cable length is
left over for pull and re-run services. This creates a convenient
disconnect point, making well intervention more efficient.
Wellside Thermocouple Input Box
» Thermocouple terminations with metal ferrule sealing system. Quick disconnect system.
» Explosion-proof Teck cable gland
Page 43
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Field Installation Pictures
High-Temperature Surface Pack Off 350°C/662°F Well
Touchscreen Display for Distributed Temperature Display
Typical Wellhead Feed-Through Assembly for Bubble Tube and Thermocouple with Conax™ Split-Seal Graphite Seals
Downhole Pressure and Distributed Temperature Surface Electronic Equipment
Nitrogen Rack350°C/662°F SAGD Well with Bottomhole Bubble Tube Pressure Collection System and Coil-Deployed Thermocouple Bundle
Instrumentation Bundle Wellhead Exit Suspended Thermocouple Bundle
Page 44
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150828
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Downhole Bubble Tube Pressure Data Collection System with Distributed Downhole Temperature Data via Thermocouple Technology
ORDERING INFORMATION
Product Part Number
Downhole Type-K
thermocouple
100646
Thermocouple
cabinet
100900
Purge box 100552
Electronic cabinet 100811
One-Stop Manufacturing
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Gauge Carriers
Gauge Carriers
Page 46Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Fortified Gauge Carrier for Artificial Lift
Strong Enough For Horizontal Wells and Offshore Applications
PRODUCT SUMMARY » Easy to use clamping system securely attaches pressure sensor to tubing.
» The mounting system utilizes high strength channels that shield cables and sensor and ensure that they cannot move past the tubing collar. The clamps are secured by tapered pins.
» Provides superior protection to prevent damage during well installation.
» System is re-usable.
» Field installation is made quicker and simpler by utilizing air driven hydraulic installation tools to compress the clamp and drive the taper pins in place.
Sensor is
protected by
carbon steel shield
Sensor is secure
and can not move
up or down
Proprietary dampening system reduces shock, vibration, and G-forces exerted from downhole pump
Fortified Gauge Carrier for Artificial Lift
Page 47
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Fortified Gauge Carrier for Artificial Lift
ORDERING INFORMATION
Product Part Number
2 3/8” EUE Tubing Sensor
Mounting System
100695
2 7/8” EUE Tubing
Mounting Sensor
100694
3 1/2” EUE Tubing Sensor
Mounting System
100871
Replacement Tapered Pins 101032
Specialized Clamp Compressions
Tool & Hammer Pin
100302
Air Driven Hydraulic Clamp Setting
Tool and Hammer
PLEASE CALL
Other sizes are available.
Please call GEO PSI for more information.
One-Stop Manufacturing
Page 48Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Welded Internal Sensing Downhole Instrumentation Carrier
Cost-Effective Solution for Internal Sensing Applications
Minimal impact to drift
» Comes with 3’– 6’ Pup Assembly Matched to the Tubing String
» Pressure Testable Design
» Welded Internal Sensing Pocket. A metallurgy study is done beforehand to prevent electrolysis.
» OD of pocket is 1.006”
» A protective shroud or fins can be used to protect the gauge
High Pressure (HiP) metal-to-metal sealing technology. The gauge seal is pressure rated to 25,000 psi.
FEATURES
Welded Internal Sensing Downhole Instrumentation Carrier
Page 49
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Welded Internal Sensing Downhole Instrumentation Carrier
ORDERING INFORMATIONWelded internal sensing downhole instrumentation carrier is a custom product.
Please call for ordering infomation.
STEP 1 | Select tubular size
STEP 2 | Select material
STEP 3 | Select threat type
STEP 4 | Casing size and weight
and grade
STEP 5 | Call GEO PSI
One-Stop Manufacturing
Page 50Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Unibody Downhole Sensor Mandrel
GEO PSI’s unibody gauge mandrel is
designed to provide maximum protection for
the downhole sensor without compromising
strength or drift in the tubing string.
RECOMMENDED APPLICATION Ideal for wells that are highly deviated or horizontal. Also
ideal for high-pressure applications.
KEY FEATURES » Unibody design
» Full drift inside diameter
» Same material grade, burst, and tensile strength and corrosion resistance properties as the tubing string
» Metal-to-metal seals
» Pressure-testable design
» Autoclave connection
Illustration Thread Type
API EUE
Atlas Bradford FLS-4S
Atlas Bradford HD-L
Atlas Bradford RTS-6
Atlas Bradford RTS-8
Atlas Bradford SB-8
Atlas Bradford ST-L
Atlas Bradford TC-4S
Atlas Bradford TC-II
BTC
BTCL
Hydril Series 500—Type 503
Hydril Series 500—Type 511
Hydril Series 500—Type 553
Hydril Series 500—Type 553
Hydril Series 500—Type 563
Kawasaki Steel Premium Fox
Kawasaki Steel Bear
VAM—New VAM
VAM ACE Modified
VAM ACE XS_XS C
VAM ACE
VAM FJL
VAM PRO
VAM TOP HT
VAM TOP
PREMIUM-QUALITY SENSOR MANDREL TUBULAR THREAD
Premium Unibody Quality Sensor Mandrel
ADVANTAGES • Compact design. Easy and
straightforward installation.
• GEO PSI provides carriers that are
manufactured with a blank core.
Threading is applied to match the
characteristics of the tubing string.
• Pressure testable design.
Unibody Downhole Sensor Mandrel
Page 51
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Unibody Downhole Sensor Mandrel
One-Stop Manufacturing
TUBULAR SIZE CHARACTERISTICS RATING
2 3/8” / 60.31 mm
Material
L80, 4140
INCONEL 718
CR13
Maximum tensile 102,990 lbs
Maximum burst 14,970 psi
Maximum collapse 15,280 psi
Tubing weight 5.95 lb/ft
Minimum inside diameter 1.876" / 47.650 mm
Maximum outside diameter 3.84" / 97.536 mm
2 7/8” / 73.03 mm
Material
L80, 4140
INCONEL 718
CR13
Maximum tensile 105,570 lbs
Maximum burst 10,570 psi
Maximum collapse 11,160 psi
Tubing weight 6.50 lb/ft
Minimum inside diameter 2.441" / 62.001 mm
Maximum outside diameter 4.50" / 114.3 mm
3 1/2” / 88.9 mm
Material
L80, 4140
INCONEL 718
CR13
Maximum tensile 159,090 lbs
Maximum burst 10,160 psi
Maximum collapse 10,530 psi
Tubing weight 9.30 lb/ft
Minimum inside diameter 2.992" / 75.996 mm
Maximum outside diameter 5.16" / 131.064 mm
4 1/2” / 114.3 mm
Material
L80, 4140
INCONEL 718
CR13
Maximum tensile 208,730 lbs
Maximum burst 8,430 psi
Maximum collapse 7,500 psi
Tubing weight 12.75 lb/ft
Minimum inside diameter 3.958" / 100.533 mm
Maximum outside diameter 5.98" / 151.892 mm
Available Casing Unibody Mandrel Sizes
5 1/2” 7” 8 5/8” 9 5/8”
Internal sensing gauge connection.
High-pressure fitting metal-to-metal sealing. Pressure testable.
Protective shroud covers downhole gauge.
Ordering InstructionsSTEP 1 | Select tubular size
STEP 2 | Select material
STEP 3 | Casing size and weight or
bore hole size
STEP 4 | Call GEO PSI
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Downhole Instrumentation Cables
Downhole Instrumentation Cables
Page 53Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
4 mm (0.160”) Diameter. 150°C (302°F) Temperature Rated. GEO PSI manufactures various cold-formed, tungsten-inert-gas-welded stainless steel downhole
instrumentation cables. Bare and encapsulated cables are marked with depth, manufacturing lot
number, and other product information. Products can be manufactured to custom lengths and ship
on heat-treated, certified wooden pallets and reels. Metal reels are also available.
PRODUCT SUMMARY GEO PSI proudly manufactures products that meet or exceed the rigorous American Society for Testing and
Materials (ASTM) A632 and ASTM E426 standards for stainless steel tubing.
4 mm (0.160”) downhole instrumentation cable (also known as tubular encapsulated cable [TEC] is the ideal
combination of strength and flexibility. The 0.762 mm (0.030”) stainless steel wall thickness is stronger than most
6.35 mm (0.250”) TEC cables, which have wall thicknesses of 0.711 mm (0.028”) or 0.889 mm (0.035”). The
4 mm (0.160”) form is flexible enough to easily exit any standard wellhead, flowline, or casing wing valve.
150°C (302°F) Downhole Instrumentation Cable
Illustrated: Round encapsulated
Illustrated: Square encapsulated
Illustrated: Bare cable
APPLICATIONS• Wellbore-suspended
• Surface read out
• Drop spools
• e-Slickline
• Pulled through coiled tubing
• Attached to tubing
• Cemented behind casing
150°C (302°F) Downhole Instrumentation Cable
Page 54
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
150°C (302°F) Downhole Instrumentation Cable
One-Stop Manufacturing
TECHNICAL SPECIFICATIONSMetal jacket Material Stainless steel 316L
Outside diameter (1) 4 mm/0.1575”
Wall thickness 0.76 mm/0.030”
Surface finish Hardness 34.8 HRC at RHC(2)
Seam Gas tungsten arc weld
Weld quality (3) Eddy inspection
Insulation Material Tefzel black
Operating temperature 150°C/302°F
Conductor Core Stranded bare copper 19 strands of 30 AWG(4)
Size 18 AWG
Diameter 1.168 mm/0.046”
Electrical Conductor DC resistance 6.1 Ω/1,000 ft
Armor DC resistance 22.5 Ω/1,000 ft
Capacitance 0.046 μF/1,000 ft
Inductance 146 μH/1,000 ft
Test rating (megohmmeter) 200 G Ω/1,000 m at 500 V
Operating voltage 32 VDC(5)
Mechanical Weight (bare) 0.051 lb/ft
Weight (encapsulated) 0.09 lb/ft
Breaking tension 2,140 lbs
Safe operating tension 1,300 lbs
Encapsulation (optional)
Material Polypropylene
Color Yellow
Size 11 mm x 11 mm/0.433” x 0.433” square or round
NOTES: (1) Reference specification: ASTM A636; tolerance 0.1575” – 0.1605”. (2) Rockwell Hardness Scale measured in c-scale. (3) Reference specification: ASTM E426. (4) American wire gauge. (5) Higher voltage rated product available upon request.
ORDERING INFORMATION
Product Part Number
150°C bare 100182
150°C encapsulated 100221
Wooden Reel (48” x 18” x 30”) 100383
Wooden Reel (40” x 10” x 32”) 100204
Wooden Reel (48” x 29” x 36”) 101750
Steel Reel (48” x 24” x 30”) 101086
Steel Reel (50” x 32” x 30”) 101087
Steel Reel (56” x 32” x 30”) 100219
Heat Treated Certified Pallet 100384
Protective End Caps 100094
Tube Wire Preparation Kit 101993
Gold Connector Pins 100289
Capacitance and Resistance Meter
101992
¼” MNPT Bored Through 4mm Compression Fitting
100092
½” MNPT Bored Through 4mm Compression Fitting
101035
Spare Front and Back Ferrules 4mm
100093
Splice 4mm to 4mm 100528
Splice 4mm to ¼” 101878
Y Splice 4mm 100530
One-Stop Manufacturing
Page 55Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
200°C (392°F) Downhole Instrumentation Cable
4 mm (0.1575”) Diameter. 200°C (392°F) Temperature Rated.
GEO PSI manufactures various cold-formed, tungsten-inert-gas-welded stainless
steel downhole instrumentation cables. Bare and encapsulated cables are marked
with depth, manufacturing lot number, and other product information.
Our products can be manufactured to custom lengths and ship on heat-treated,
certified wooden pallets and reels. Metal reels are also available.
PRODUCT SUMMARYGEO PSI proudly manufactures products that meet or exceed the rigorous American Society for
Testing and Materials (ASTM) A632 and ASTM E426 standards for stainless steel tubing.
Our 4 mm (0.160”) downhole instrumentation cable (also known as tubular encapsulated cable
(TEC) is the ideal combination of strength and flexibility. The 0.762 mm (0.030”) stainless steel
wall thickness is stronger than most 6.35 mm (0.250”) TEC cables, which have wall thicknesses
of 0.711mm (0.028”) or 0.889 mm (0.035”). The 4.064 mm (0.160”) form is flexible enough
to easily exit any standard wellhead, flowline, or casing wing valve.
APPLICATIONS• Wellbore-suspended
• Surface read out
• Drop spools
• e-Slickline
• Pulled through coiled tubing
• Attached to tubing
• Cemented behind casing
Illustrated: SS 316L Bare
200°C (392°F) Downhole Instrumentation Cable
Page 56
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
200°C (392°F) Downhole Instrumentation Cable
TECHNICAL SPECIFICATIONSMetal jacket Material Stainless steel 316L
Outside diameter 4 mm/0.1575”(1)
Wall thickness 0.76 mm/0.030”
Surface finish Hardness 34.8 HRC at RHC(2)
Seam Gas tungsten arc weld
Weld quality(3) Eddy inspection
Insulation Material Tefzel red
Operating temperature 200°C/392°F
Conductor Core Tinned Copper 19 strands of 30 AWG(4)
Size 18 AWG
Diameter 0.046”/1.168 mm
Electrical Conductor DC resistance 6.1 Ω/1,000 ft (304.8 m)
Armor DC resistance 22.5 Ω/1,000 ft (304.8 m)
Capacitance 0.046 μF/1,000 ft (304.8 m)
Inductance 146 μH/1,000 ft (304.8 m)
Test rating (megohmmeter) 200 G Ω/1,000 m at 500 V
Operating voltage 32 VDC(5)
Mechanical Weight (bare) 0.051 lb/ft
Weight (encapsulated) 0.09 lb/ft
Breaking tension 2,140 lbs/971 kg
Safe Operating tension 1,300 lbs/590 kg
NOTES: (1) Reference specification: ASTM A636; tolerance 0.1575”–0.1605”. (2) Rockwell hardness scale measured in c-scale. (3) Reference specification: ASTM E426. (4) American wire gauge. (5) Higher voltage rating available upon request.
One-Stop Manufacturing
ORDERING INFORMATION
Product Part Number
200°C bare 101542
Wooden Reel (48” x 18” x 30”) 100383
Wooden Reel (40” x 10” x 32”) 100204
Wooden Reel (48” x 29” x 36”) 101750
Steel Reel (48” x 24” x 30”) 101086
Steel Reel (50” x 32” x 30”) 101087
Steel Reel (56” x 32” x 30”) 100219
Heat Treated Certified Pallet
100384
Protective End Caps 100094
Tube Wire Preparation Kit 101993
Gold Connector Pins 100289
Capacitance and Resistance Meter
101992
¼” MNPT Bored Through 4mm Compression Fitting
100092
½” MNPT Bored Through 4mm Compression Fitting
101035
Spare Front and Back Ferrules 4mm
100093
Splice 4mm to 4mm 100528
Splice 4mm to ¼” 101878
Y Splice 4mm 100530
Page 57
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
PRODUCT SUMMARYType K thermocouple sensors provide the most robust and reliable solution for
temperature measurement in high-temperature reservoirs. Compared to fiber optic
solutions, thermocouples are more cost-effective—and they do not suffer the effect of
hydrogen darkening.
Illustrated: 285°C/545°F 4 mm/0.160” outside diameter four-conductor cable with swagelok fitting and Type K thermocouple.
TYPE K FOUR-WIRE THERMOCOUPLE SPECIFICATIONS Temperature range -40°C to 285°C
(300ºC for short term)
Temperature accuracy <+/- 2.2°C
Temperature measurement points 2 (Redundant or Spaced Apart)
Repeatability < ±0.1°C
Depending on logger
Stability Excellent
Resolution Depending on logger input
Time constant 1 sec
Construction material Stainless steel 316L
Vibration Excellent
Shock Excellent
285°C (545°F) Type K Thermocouples
285°C/545°F Four-Conductor Thermocouple Downhole Instrumentation Cable
Applications• Single-point and
distributed temperature monitoring
• Coiled tubing instrumentation bundles
• SAGD/Geothermal
Services Available• Technical support
• Installation and training
• Maintenance
285°C (545°F) Thermocouples
Page 58Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
285°C (545°F) Type K Thermocouples
Using Thermocouples for Downhole Temperature MeasurementBREAKTHROUGH—IMPROVED RELIABILITY FOR DOWNHOLE THERMOCOUPLESGEO PSI takes pride in being a dynamic, innovative company. We
never accept the status quo. A considerable portion of our R&D budget
and engineering time is targeted towards developing innovative high-
temperature downhole instrumentation cable solutions.
We have developed an exclusive manufacturing process that has greatly
increased the reliability of thermocouples for use in downhole steam-
assisted gravity drainage (SAGD), enhanced oil recovery (EOR), geothermal,
and other high-temperature applications by eliminating many of the weak
points of conventional thermocouple systems.
Tubular encapsulated cable (TEC) is the preferred package for downhole
instrumentation, including thermocouples, and is manufactured by a cold-
forming tube mill.
The manufacturing process begins with stainless steel strip that is
continuously formed into a tube through a progressive series of rollers. The
thermocouple conductors are injected into the tube just before the tube is
welded together using tungsten inert gas welding. After the weld, the tube
is reduced again until it reaches the
final diameter.
Product quality is automatically
and manually monitored during the
entire manufacturing process. The
tube’s welded seam is monitored
by an eddy current tester, and the
diameter of the finished product is
measured and recorded by a 3D
profilometer. Every cable is
manually inspected before customer
shipment.
Close Up Of Rollers Forming Tube
Ready-to-ship warehouse inventory
GEO PSI Tube Mill
Ready to DeliverOur thermocouple instrumentation cable is:
• Manufactured to custom lengths
• Produced with a quick turnaround
• Available in lengths up to 4,000 m
Page 59
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
285°C (545°F) Type K Thermocouples
How Do We Make a Better Downhole Thermocouple Cable?Thermocouples are extremely sensitive to corrosion.
Most downhole thermocouple systems rely on silver
brazing to attach thermocouples to a stainless
steel instrumentation line. It’s extremely difficult to
consistently make corrosion-proof joints.
GEO PSI has invented a manufacturing process
at our tube mill manufacturing facility in Calgary,
Canada that results in the thermocouples being
hermetically sealed inside the instrumentation line,
which protects them from oxidation and other forms
of contamination.
Redundancy and Distributed Spacing. GEO PSI can
install a redundant thermocouple sensor at each
measurement point. This is beneficial for backup
purposes and result verification. Alternatively,
thermocouples can be spaced apart for distributed
temperature measurement.
Pump Down System Advantage. Because GEO PSI’s
thermocouples are not externally attached, there is no
change to the outside diameter of the instrumentation
cable. This is convenient when deploying pump down
bundles in coiled tubing deployments. We can fit more
measurement points in smaller-diameter, coiled
tubing strings.
Filler/Safe-Handling Section. Thermocouples are
typically installed in bundles or attached to strength
membrane for pump down purposes. To avoid damage
from handling or banding, GEO PSI has developed a
1- to 2-m or 4- to 6-ft safe handling section at the end of
our instrumentation cable, greatly reducing any wear or
tear while pulling instrumentation bundles through
coiled tubing.
MICA-Free Cables. While MICA insulation offers
excellent temperature ratings, it is susceptible to
moisture wicking and can be difficult to use in the field,
especially when creating reliable surface terminations.
Excess humidity can lead to sensor failures, and
MICA insulation is difficult to strip and terminate. In
addition, poor brazing technique on MICA cables cause
attenuation, resulting in early failures or inaccurate
temperature readings.
GEO PSI thermocouple systems use a special form of
perflouorokoxy (PFA) as insulation, which has a safe
operating temperature of nearly °C. It’s extremely easy
to work with in the field. No soft leads are required at the
termination, making our solution more cost-effective and
quicker to deploy.
Improved Tensile Strength and Crush Resistance. Our
thermocouple cable sheath is slightly larger than
3.175 mm (0.125”). Our 4.064 mm cable (0.160”) is
based on Slickline sizing, and our stainless steel wall
thickness is 0.762 mm (0.030”), compared to 0.584 mm
(0.023”). And, our tensile operating strength and crush
resistance is more than 50% better than 3.175 mm
(0.125”) downhole instrumentation lines.
Thermocouple measurement points can be redundant or spaced apart inside the same TEC.
Ideal Applications• SAGD
• EOR
• Geothermal
• Coiled tubing deployed instrumentation
Page 60
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
ORDERING INFORMATION
Product Part Number
285°C Thermocouple Cable 100646
Wooden Reel (48” x 18” x 30”)
100383
Wooden Reel (48” x 29” x 36”)
101750
Heat Treated Certified Pallet
100384
Protective End Caps 100094
¼” MNPT Bored Through 4mm Compression Fitting
100092
½” MNPT Bored Through 4mm Compression Fitting
101035
Spare Front and Back Ferrules 4mm
100093
One-Stop Manufacturing
285°C (545°F) Type K Thermocouples
TECHNICAL SPECIFICATIONSMetal
jacket
Material Stainless steel 316L
Outside diameter 4 mm/0.160” (1)
Wall thickness 0.76 mm/0.030”
Surface
finish
Hardness 34.8 HRC at RHC (2)
Seam Gas tungsten arc weld
Weld quality (3) Eddy inspection
Insulation Material PFA
Diameter 2.413 mm/0.095”
Long Term Operating Temperature 285°C/545°F
Short Term Maximum Temperature 300°C/572°F (4)
Color Red and Yellow
Core Alumel x 2 (RED INSULATION)
Chromel x 2 (YELLOW INSULATION)
4 x 24 AWG stranded
Conductor DC resistance
Return Loop (Red + Yellow)
1,532 Ω/1,000 ft at 20°C
Armor DC resistance 22.5 Ω/1,000 ft
Operating voltage 1 VDC
Mechanical Weight 0.051 lb/ft
Breaking tension 2,140 lbs
Yield tension 1,300 lbs
Crush 33,450 lbf over 1”
Yield tension 1,300 lbs
NOTES: (1) Reference specification: American Society for Testing and Materials (ASTM) A636. (2) Rockwell scale hardness measured in c-scale. (3) Reference specification: ASTM E426. (4) Cannot exceed 300°C. Call GEO PSI for additional information.
Page 61Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
4 CONDUCTOR DOWNHOLE INSTRUMENTATION CABLETemperature range -40°C to 300°C / -40°F to 572°F
Stability Excellent
Construction material Stainless steel 316L
Vibration Excellent
Shock Excellent
300°C (572°F) Downhole Instrumentation Cable
Stainless Steel Armor with Four Insulated ConductorsGeo Pressure Systems Inc. (GEO PSI) manufactures various cold-formed, tungsten-inert-gas-
welded stainless steel downhole instrumentation cables. Bare and encapsulated cables are
marked with depth, manufacturing lot number, and other product information. Our products
can be manufactured to custom lengths and ship on heat-treated, certified wooden pallets
and reels. Metal reels are also available.
APPLICATIONS• Permanent Downhole
Monitoring
• Piezometers and
Strain Gauges
• SAGD & Geothermal
• Hydrology
• e-Slickline /
Digital Slickline
QUALITY ASSURANCEOur products meet or exceed the
rigorous American Society for
Testing and Materials (ASTM) A632
and ASTM E426 standards for
stainless steel tubing.
PRODUCT SUMMARYGEO PSI’s innovative multi-conductor tubular
encapsulated cable (TEC) ideal for permanent downhole
gauge installations, e-Slickline, and coiled tubing
deployed instrumentation. This cable combines strength
and flexibility, making it the go-to solution for many
downhole applications using piezometers and other
instruments that are high-temperature rated or require
multiple conductors.
Illustrated: 150°C / 302°F encapsulated stainless steel cable.
Illustrated: 300˚C / 572˚F bare stainless cable.
300°C (572°F) Four-Conductor Downhole Instrumentation Cable
Page 62
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
300°C (572°F) Downhole Instrumentation Cable
TECHNICAL SPECIFICATIONSMetal jacket Material Stainless steel 316L
Outside Diameter 4 mm / 0.160” 1
Wall Thickness 0.76 mm / 0.030”
Surface finish Hardness 34.8 HRC at RHC2
Seam Gas tungsten arc weld Weld Quality Eddy inspection 3
Insulation Material PFA Diameter 2.413 mm/0.095”Maximum
Operating
Temperature 4
300°C / 572°F
Color Black, White, Blue, Red
Core Tinned Copper 4 x 24 AWG 5 stranded Electrical Voltage Rating 500 V
Conductor DC
Resistance
24 Ω per 1,000 ft @ 68°F
7.874 Ω per 100m @ 20°CArmor DC
Resistance
22.5 Ω per 1,000 ft @ 68°F
7.382 Ω per 100m @ 68°FCapacitance 6 » Single conductor to armor
31.5pF per foot
» Single conductor to
opposite conductor
13 pF per foot
» Single conductor to
adjacent conductor
16 pF per foot
» Pair to pair 31 or 41pF
per foot (depending on
position)
» All conductors shorted
together to armor 77pF
per foot
Inductance 6 » Loop with adjacent
conductors pairs
0.13 uH per foot
» Loop with opposite
conductors pairs
0.05 uH per footMechanical Weight 0.051 lb/ft (bare cable)
Breaking Tension 2,140 lbs / 971 kgYield Tension 1,300 lbs / 590 kg
Optional External
Encapsulation
11 mm (0.433”)
square or round
Maximum temperature rating 150°C / 302°F
NOTES: (1) Reference specification: ASTM A636. (2) HRC/RHC: Rockwell Hardness measured in C-Scale. (3) Reference
specification: ASTM E426. (4) Cannot exceed 300°C (5) American Wire Gauge. (6) Measured with Hewlett Packard 4192A.
ORDERING INFORMATION
Product Part Number
300°C Quad Conductor Bare
100440
150°C Quad Conductor Encapsulated
101547
Wooden Reel (48” x 18” x 30”)
100383
Wooden Reel (40” x 10” x 32”)
100204
Wooden Reel (48” x 29” x 36”)
101750
Steel Reel (48” x 24” x 30”)
101086
Steel Reel (50” x 32” x 30”)
101087
Steel Reel (56” x 32” x 30”)
100219
Heat Treated Certified Wood Pallet
100384
Protective End Caps 100094
Tube Wire Preparation Kit 101993
¼” MNPT Bored Through 4mm Compression Fitting
100092
½” MNPT Bored Through 4mm Compression Fitting
101035
Spare Front and Back Ferrules 4mm
100093
Splice 4mm (Four Conductor to Four Conductor)
100529
One-Stop Manufacturing
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Cable Protectors
Cable Protectors
Page 64
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
IECEx Certified
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Downhole Centralizer Clamp
Cost Effective SolutionGEO PSI’s Downhole Centralization Clamp provides a simple,
cost-effective solution for centralizing and protecting downhole
instrumentation in a tubing string.
FEATURES » Manufactured from high-carbon, corrosion-resistant steel
» Easy to install
» Secured by taper pins
» Multiple centralizers can be utilized depending on wellbore conditions
APPLICATIONS » Great protection against tubing oscillation from downhole fluid pumps
» Very effective for high-output ESP and PC pump completions
» Effective for severe dog legs and horizontal installations
ORDERING INFORMATIONSeveral Hundred options are available
Contact GEO PSI with the following information:
» Tubing size and thread connection type
» Tubing weight
» Casing size and thread connection type
» Casing weight
Downhole Centralizer Clamp
Page 65Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Heavy-Duty Cable Protectors
Reliable and Easy To InstallGEO PSI’s heavy-duty cable protectors provide the most protection for
downhole instrumentation cable in severe conditions.
RECOMMENDED APPLICATIONIdeal for wells that are highly deviated or horizontal.
Also ideal for protecting against oscillation in high
capacity ESP and PC Pumps.
KEY CONSIDERATIONS » Mild-corrosion-resistant, high-carbon steel
» Available for any size of tubing or casing
» Superior strength
» Superior protection
» Customizable for gas lift mandrels and subsurface safety values
» Mid-joint and over-the-collar design available
BEWARE OF IMITATORSMany knock clamps are tack
welded, but GEO PSI’s clamps
are spot welded.
Difference Between Spot Welding and Tack Welding
• Tack welding is a preliminary process in any welding project and takes place before spot welding
• Tack welding ensures that parts to be welded finally through spot welding are held securely and properly aligned, spot welding finally joins the parts together.
GEO PSI cable protectors are of the highest quality
Heavy-Duty Cable Protectors
Page 66
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Heavy-Duty Cable Protectors
ORDERING INFORMATION
Thousands of solutions are available to accomodate any type of tubing or casing.
Contact GEO PSI with the following information:
Tubing Protectors Casing Protectors
» Tubing size
» Tubing Weight
» Connection type
» Type and number of
instrumentation cables
» Casing size
» Casing weight
» Connection type
» Casing size
» Connection type
» Weight
» Type and number of
instrumentation cables
» Bore hole size
Mechanical and power tools are available for sell or rent.
One-Stop Manufacturing
GEO PSI technician on rig floor
Page 67Last Revised: 150827
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Protects cable at each collar joint.
Light-Duty Cable Protectors
Cable ProtectorsECONOMICAL AND EASY TO INSTALL GEO PSI’s light-duty cable protectors prevent damage to tube wire
instrumentation cable in vertical to slightly deviated completions.
RECOMMENDED APPLICATIONLight-duty cable protectors are recommended for situations where banding
alone is not suitable. They are ideal for wells that are vertical or have less
than 30° deviation.
GEO PSI keeps a large inventory of light-duty downhole cable protectors
in stock at all times. The protectors are designed to work with both bare or
encapsulated TEC cables.
TUBULAR SIZE RUNNING OPEN-DIAMETER PART NUMBER
2 3/8” EUE 3.829” / 97.2566 mm 100320
2 7/8” EUE 4.449” / 113.0046 mm 100320
3 1/2” EUE 5.148” / 130.7592 mm 100320
4 1/2” EUE 6.388” / 162.2552 mm 101472
Cross-section view of cable protection.
Light-Duty Cable Protectors
Page 68
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Light-Duty Cable Protectors
One-Stop Manufacturing
More meat where it matters. This part of the clamp may catch a casing collar—where protection matters the most.
THE COMPETITION
The GEO PSI clamp has 50% more material than other cable protectors, making it considerably stronger. 12 AWG (American Wire Gauge) carbon steel.
Zinc Coating—Rust Resistant
Banding is applied on top of the instrumentation cable, not underneath it, making our clamp more secure and time efficient on the rig floor.
GEO PSI
The GEO PSI Advantage
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Splices
Splices
Page 70Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
4 mm (0.160”) Pressure-Testable Easy Connect Downhole Instrumentation Cable Splice
Our premium pressure-testable splice with Easy Connect advantage.
Splice Assembly: Easy and quick to make-up—Reliable performance
PRODUCT FEATURES » Design allows direct connection to armoured
cables using metal-to-metal seals.
» Tough 316L stainless steel construction ensures that this splice can be deployed in hostile environments within the oil and gas industry.
» Pressure testable design reduces failures.
» Effective and reliable solution for joining 4 mm/0.160” or ¼” (6.35mm) without compromising reliability
» Complete metal-to-metal sealing system
EASY CONNECT ADVANTAGECablehead failure is the number one cause for permanent downhole gauge
failures. GEO PSI has created an innovative system(1) that greatly improves
cablehead success.
1. Plug and play.
2. Metal-to-metal sealing front and back ferrules are attached and secured in place with a hex nut.
3. A secondary cablehead is attached, which has an additional set of metal-to-metal sealing ferrules.
4. Pressure test port allows GEO PSI to conduct a pressure test on the primary and secondary connection.
(1) Patent pending.
4 mm (0.160”) Pressure-Testable Easy Connect Downhole Instrumentation Cable Splice (Patent Pending)
Metal-to-Metal Sealing
Metal-to-Metal Sealing
Pressure Test Port
Isolated Glass Feed-Through
Isolated Glass Feed-Through
Pressure Test Port
APPLICATIONS• Packer feed-thru
• Repairing damaged lines
• Combining lengths
of cable
• Mate different
sizes of TEC
1
2
3
4
4 mm (0.160”) Pressure-Testable Easy Connect Downhole Instrumentation Cable Splice (Patent Pending)
Page 71
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
4 mm (0.160”) Pressure-Testable Easy Connect Downhole Instrumentation Cable Splice (Patent Pending)
TECHNICAL SPECIFICATIONS
Proof pressure 137,895 kpa (20,000 psi)
Compatible TEC cables 4 mm (0.160”) and 6.35 mm (0.25”)
Construction material Stainless steel 316L
Outside diameter 12.7 mm (0.875”)
Length 269.875 mm (10.625”)
ORDERING INFORMATION
Product Part Number
4 mm to 4 mm (0.160”) Single conductor
100528
4 mm to 0.25” Single conductor
101878
4 mm to 4 mm Four conductor
100529
0.25” to 0.25” Single Conductor
101543
4mm/0.160” splice field installation toolkit (optional)
PLEASE CALL
Cablehead rebuild kit (2 required)
101468
One-Stop Manufacturing
Page 72Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Pressure-Testable Easy Connect Downhole Instrumentation Cable Y Splice (Patent pending)
PRODUCT SUMMARY » Complete metal-to-metal sealing system
with multiple sealing points
» Up to right downhole sensors can be attached to a single line
» Stainless steel 316 or Inconel 718 construction
EASY CONNECT ADVANTAGECablehead failure is the number one cause for
permanent downhole gauge failures. GEO PSI has
created an innovative system(1) that greatly
improves cablehead success.
1. Plug and play.
2. Metal-to-metal sealing front and back ferrules are attached and secured in place with a hex nut.
3. A secondary cablehead is attached, which has an additional set of metal-to-metal sealing ferrules.
4. Pressure test port allows GEO PSI to conduct a pressure test on the primary and secondary connection.
(1) Patent pending.
Y-SPLICE ASSEMBLY. RELIABLE, EASY AND FAST TO SET-UP.
Pressure-Testable Easy Connect Downhole Instrumentation Cable Y-Splice
Easy connect cablehead
Pressure-testable secondary cablehead
Pressure-testable secondary cablehead
Isolated glass feed-through
Isolated glass feed-through
Pressure-testable secondary cablehead
1
2
3
4
ADVANTAGES• Allows multiple gauges to
be connected to a single
instrumentation cable
• Features metal-to-metal
seals and tough 316L
stainless steel construction
Easy connect cablehead
Pressure-Testable Easy Connect Downhole Instrumentation Cable Y Splice (Patent Pending)
Page 73
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for Success
INTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
TECHNICAL SPECIFICATIONSProof pressure 137,895 kpa (20,000 psi)
Compatible TEC cables 4 mm (0.160˝), and 6.35 mm (0.25”)
Construction material Stainless steel 316L or Inconel 718
Outside diameter 22.2 mm (7⁄8”)
Length 36.2 cm (14 ¼”)
Width 5.4 cm mm (2 1⁄8”) including hex nuts
ORDERING INFORMATION
Product Part Number
6.35 mm (0.25”) TEC
Inconel
101949
4 mm (0.160”) TEC
Stainless Steel 316L
100530
6.35 mm (0.25”) TEC
Stainless Steel 316L
100528
4 mm (0.160”)
4-conductor 4-to-4-to-1
100493
4 mm (0.160”)
4-conductor 4-to-1-to-1
100532
Cablehead rebuilt kit
(3 required)
101468
Pressure-Testable Easy Connect Downhole Instrumentation Cable Y Splice (Patent pending)
One-Stop Manufacturing
GEO PSI loading bays.
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Wellhead Pressure Control
Wellhead Pressure Control
Page 75Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
ENGINEERED WITH SAFETY IN MINDSafety should never be compromised when exiting
instrumentation cable from the wellbore, especially
in the presence of surface gas pressure. Only a
metal-to-metal sealing system can adequately isolate
stainless steel instrumentation cable from the outside
environment. Furthermore, a high-pressure glass
feed-through, secondary barrier, isolates any pressure
from travelling through the conductor in the event of a
downhole cable breach.
A preventive safety bleed-off is furnished for
authorized operators or technicians servicing the
wellhead.
Flexible Design The wellhead feed-through system is modular and can
be configured to exit through a wellhead NPT port,
casing vent, or designated flow line.
KEY COMPONENTS » Hermetically sealed glass feed-through system
» Stainless steel 316L body
» Metal-to-metal sealing system for downhole instrumentation cable
» CSA/UL-approved Appleton junction box
» ½” NPT connection port
» Hazardous area approved Teck cable gland for CSA metal-shielded surface cable
Wellhead Feed-Through
Certified version available
Wellhead Feed-Through
Safety Bleed-Off
Certification Tag*
Hazardous Area Cable Gland
Armoured Surface TECK Cable
NPT Connection and Metal-to-Metal Sealing Technology
High-Pressure Glass
Electrical feed-through prevents gas and fluids from migrating to surface electronics. Optional certified version available.
CSA/UL Approved Junction Box
*Only for GEO PSI IECEx approved sensors
Wellhead Feed-Through
Page 76
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for Success
INTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
ORDERING INFORMATION
Product Part Number
Single conductor
wellhead feed-through
100370
Four conductor wellhead
feed-through
101039
2” Casing bowl assembly
(3,000 psi wellhead)
100878
2” Casing bowl assembly
(5,000 psi wellhead)
101399
14/2 armoured surface
cable (CSA/UL)
100389
14/4 armoured surface
cable (CSA/UL)
100747
CSA/UL junction box
2 x ½” FNPT
100367
½” explosion-proof
TECK gland
100362
½” non-hazardous area
TECK gland
100390
Back nut lug
ground bushing
100944
Please call GEO PSI regarding
certified versions.
Other customer configurations
are available.
One-Stop Manufacturing
Wellhead Feed-Through
Pictured: GEO PSI instrumentation cable feed-through casing bowl assembly
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Surface Electronics
Surface Electronics
Page 78
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150605
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
G6 Downhole Gauge Controller
One-Stop Manufacturing
ORDERING INFORMATION
Model Part Number
G6 100299
Multi-gauge G6 101950
DIN rail bracket 101293
Wireless G6 100954
One-Stop Manufacturing
G6 Downhole Gauge Controller » Decodes downhole telemetry and converts both,
pressure and temperature data to 4-20 mA and/or RS485 Modbus protocol. Full downhole gauge diagnostic information can be transmitted through RS485.
» Class 1, Div 2 (Group C&D) certified.
» Compatible with any PLC, VFD, or Surface Logger, Memory Module, Display, Satellite, SCADA, Radio Telemetry available on the market.
» DIN rail mounting bracket is available.
» Very low power consumption ensures maximum performance for Solar Power Installation in Remote Locations.
» Includes SCADA resettable limit counter and watch dog timers. Under voltage detection for solar. Controls power to radio. Optional status lights.
» Multi-gauge. 1 to 8 quartz and/or piezoresistive sensors can be controlled by a single G6.
G6 Downhole Telemetry Decoder
G6 mini cabinet
G6 Downhole Gauge Controller
Page 79
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150827
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Generic Data Acquisition System
The most important aspect of downhole monitoring is integrating data into our customers’ network and control systems.AT GEO PSI WE BELIEVE IN USER-FRIENDLY TECHNOLOGICAL SOLUTIONSGEO PSI’s cabinet has a color touchscreen logger that is intuitive and easy to operate.
Furthermore, we can connect easily to any SCADA system, Distributed Control System
(DSC), or VSD through RS485, RS232, Ethernet, and other available systems. Our
data acquisition system is expandable and can easily connect to virtually any surface
instrumentation, including pressure gauges, flow meters, actuators, and tank storage-level
equipment. All of GEO PSI cabinets are CSA/UL approved for either hazardous or general-
purpose locations.
GEO PSI focuses on delivering practical and reliable solutions with excellent workmanship.
Outside View of NEMA 4X Cabinet
KEY FEATURES: » Small, compact, and elegant enclosures
» Color touchscreen display available
» Intuitive interface with on-screen instruction manual
» Up to 32 GB onboard memory
» RS485, RS232, Ethernet outputs
» Expandable for additional surface instrumentation inputs
» Safe operating temperature of -50°C to +75°C (-58°F to 167°F)
» CSA/UL-approved enclosure
» NEMA 3 or 4
OTHER CAPABILITIES » Topography analysis
» SCADA radio programming
» Factory acceptance testing
» Intrusion alert notification
» Custom PLC programming
Inside View of Cabinet Color Touchscreen Logger
Generic Data Acquisition System
Page 80Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Generic Solar RTU Cabinet and G6 Digital Downhole Gauge Controller
Geo Pressure Systems Inc.
(GEO PSI) is the leader for
Remote Terminal Unit (RTU)
cabinet assembly. We focus
on delivering practicality and
reliability through excellent
workmanship and component
selection.
All GEO PSI cabinets
are CSA Approved for
hazardous location or general
purpose location. Our back
pan design is spacious
and accommodating for
future expansion and field
troubleshooting.
STAND / CABINET FEATURESNorthern solar packages Solar power system
offers 20–660 W of solar energy from panels
mounted on a field-adjustable telescopic pole.
NEMA Type 3 or 4X certified cabinets. All
systems are earth-grounded to the cast iron
wellhead wherever possible.
Heavy-duty steel frame stand. The stand
is mountable on 5’x5’ rig mat or other skid
structure and includes an innovative pop-up
antenna mast unit. It is able to withstand wind
gusts > 100 km/hr (60 mph)
NEMA 3 battery chest. The typical battery
reserve is 336 hours without sunlight/charge.
BACK PAN FEATURESRTU wire diagram. A color-coded wire diagram
is attached to the inside of the cabinet door.
Wire labels. All wires are labelled in accordance
with the wiring diagram.
Terminal Labels. All terminals are numbered in
accordance to wiring diagram.
Spare fuses and a field instruction manual
are included.
Wire ferrules. All wire ends have crimp ferrules
to ensure a positive and repeatable connection.
Remote Terminal Unit Cabinet Assembly
SERVICES• Topography analysis
• Supervisory control and data
acquisition (SCADA) radio
programming
• Factory
acceptance testing
• Intrusion alert notification
• PLC programming
For extreme high-temperature environments, a shade bonnet is affixed to the cabinet structure.
Generic Solar RTU Cabinet
Page 81
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Generic Solar RTU Cabinet and G6 Digital Downhole Gauge Controller
G6 DOWNHOLE TELEMETRY DECODER » Hermetically sealed surface box decodes downhole
telemetry and converts both pressure and temperature data to 4–20 mA or RS 485 Modbus protocol.
» Compatible with any programmable logic controller, variable frequency drive, surface logger, memory module, display, satellite, SCADA system, or radio telemetry available on the market.
» DIN rail mounting bracket is available.
» Very low power consumption ensures maximum performance for solar power installation in remote locations.
» Includes SCADA retestable counter and watchdog timer.
» Up to 8 gauges can be controlled with one G6.
GEO PSI DATA LOGGER FEATURES (XL4E) » 3.5” color touchscreen with multilanguage instruction set
» Dedicated Ethernet Port and RS 485 and RS 232 modes
» Compatible with any SCADA, fiber optic, or distributed control system
» 32 GB micro SD memory card
» Field data downloadable through removable thumbdrive in a csv file
» Downhole data sample rate of 0.2 sec or slower
» Programmable digital inputs/outputs
» Expandable architecture
» Safe operating temperature of -50°C to +70°C (-58°F to +158°F)
» Class 1, Division 2 CSA certification
Please call for details and options
CSA Approved - CLASS 1 Div 2
GEO PSI XL4e Touchscreen Data Logger
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Last Revised: 150901
The Future is Real Time™
GEOPSI.com
Accessories
Accessories
Page 83Last Revised: 150506
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
4–20 mA Surface Pressure Gauges
Rosemount is the leader for 4–20 mA pressure accuracy and
temperature stability.
More than 75 temperature calibration reference points.
Solution for monitoring surface pressures
High Accuracy. Intrinsically Safe. – Class1, Div1 Approved.
CERTIFIED SENSOR/TRANSMITTER SPECIFICATIONSOutput 4-20 mA
Input voltage range 12 – 24 VDC
Pressure range 500 psi to 4,000 psi, depending on
model
Pressure accuracy ± 0.075% Full Scale
Pressure drift < 0.1% per year
Temperature range -40°C to +150°C (-40°F to 302°F)
depending on model
Construction material Stainless steel 316L diaphragm
Meets or exceeds the following
standards
UL 1203; ATEX Intrinsically Safe; CSA;
UL; FM Explosion-Proof for Class 1,
Division 1 when connected properly;
Australia SAA Intrinsic Safe
Cost Effective, 4-20 mA – Class 1 Div 1 Approved.
COST-EFFECTIVE SENSOR/TRANSMITTER SPECIFICATIONSOutput 4-20 mA
Input voltage range 12 – 24 VDC
Pressure Range 1,000 psi to 3,000 psi
depending on model
Pressure Accuracy ± 0.5% Full Scale
Pressure Drift < 0.2% per year
Temperature Range -40°C to +105°C (-40°F to 221°F)
depending on model
Construction material Stainless steel 316L diaphragm
4–20 mA Surface Pressure Gauges
Page 84
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for Success
INTERNATIONALGEO PRESSURE INTERNATIONAL
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150506
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
ORDERING INFORMATION
Product Part Number
Rosemount Surface
Pressure Gauges
PLEASE
CALL
300 psi 100597
1,000 psi 100560
3,000 psi 101320
5,000 psi 101152
One-Stop Manufacturing
4–20 mA Surface Pressure Gauges
Page 85Last Revised: 150604
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
The Future is Real Time™
GEOPSI.com
One-Stop Manufacturing
Source the
Complete System from GEO PSI
Reliability Value Cost
Downhole Instrumentation Installation Equipment
Continuous Data Acquisition. 4x4 All-Terrain Truck.
Pneumatic Bander
Cannon Clamp Tools
RIG AIR & HYDRAULIC OPERATED BACK PRESSURE SPOOLER » Directional control valve
» Integrated lift points
» Integrated air pressure (cable tension) regulator, drip oiler, and water trap
» Integrated 25’ retractable air line (auxiliary output for air tools or air gun)
» Integrated 50’ air line for connection to rig air supply
» Integrated draw-works caliper brake
» Integrated storage compartment (for included four-point lifting sling)
» Included continuous data collection ring (electrical commutator) for logging signal while deploying system in wellbore
» Quick-release arbor shaft, self-adjusting drive arms, and quick-release follower nut
» Designed to accommodate spools from 24–60” diameter and overall width from 15–36”
» 2.5” solid Parkerized steel axle C/W heavy-duty Babbitt bearings
Integrated calper brake
Directional flow control valve
Integrated retractable air reel
Integrated storage for 4-point sling
Electronic communicator with swivvle
Downhole Instrumentation Installation Equipment
Page 86
Reliability Job 1™
Kno
wle
dg
eabl
e Su
ppor
t * Vertic
al Integration * Deliverability * Acco
untability
Be Positioned for SuccessINTERNATIONALGEO PRESSURE SYSTEMS INTERNATIONAL INC.
Braemar Court, Deighton Road St. Michael BB14017 Barbados
E [email protected] P +1.246.228.3814 F +1.246.434.4779
USA & CANADAGEO PRESSURE SYSTEMS INC.
Unit 17, 47 Aero Drive NE Calgary, AB T2E 8Z9 Canada
E [email protected] P +1.403.453.1300 F +1.403.730.5569
Last Revised: 150604
The Future is Real Time™
GEOPSI.com
Downhole
GaugesDow
nhole Cables (TEC)
Cable Protectors
Wellhead
Pressure ControlSurface
ElectronicsAccessories
One-Stop Manufacturing
Downhole Instrumentation Installation Equipment
ORDERING INFORMATIONPlease call for details
One-Stop Manufacturing
PROFESSIONAL TOOL PACKAGE » GEO PSI offers a full line of professional installation tools proven to
withstand the harsh environment of the rig floor. Some of these tools
are specialty tools designed in house by experienced field engineers.
Tools are shipped in a heavy-duty steel tool box for easy transport
to the rig site. Practicality, knowledge, and high-quality equipment
is our recipe for success. GEO PSI is constantly looking for ways
to reduce input costs and pass our savings on to the customer.
» Some of the main tools included in the equipment package are a back-
pressure spooling unit, pneumatic strapping tool, hydraulic clamping
tool, heavy-duty banding cart with integrated brake, and a variety of
specialized hand tools.
Our professional tool
package includes
all of the tools
necessary to complete
a standard tubing
deployed system.
Features• With more than 20 years of
continuous pressure monitoring
experience, GEO PSI can design
customized installation equipment
packages suitable for deployment
in any environment.
• Products can be certified.