Fog Lights

Download Fog Lights

Post on 13-Oct-2014

24 views

Category:

Documents

2 download

Embed Size (px)

TRANSCRIPT

<p>www.collegehillshonda.comAccessory Application Publications No.</p> <p>INSTALLATION INSTRUCTIONSPARTS LIST Right fog light</p> <p>AII40362 FOG LIGHTS P/N 08V31-SNA-100D 2009 CIVIC 4-DOORIssue Date</p> <p>AUG 2008</p> <p>6</p> <p>Wire ties</p> <p>Left fog light</p> <p>Clip</p> <p>Switch harness</p> <p>2</p> <p>Self-tapping screws</p> <p>20 A Fuse (Some may not used.) Fog light harness Relay</p> <p>Sub harness Ground bolt</p> <p>Combination light switch 2 Spring nuts</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>08V31-SNA-1D00-91</p> <p>1 of 12</p> <p>www.collegehillshonda.comTOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm and 12 mm Sockets Blanket Diagonal cutters 5 mm Hex wrench Illustration of Fog Lights installed on the vehicleRELAY SWITCH HARNESS COMBINATION LIGHT SWITCH</p> <p>INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft codes for the audio system and navigation system (if equipped), then write down the radio presets. Disconnect the negative cable from the battery. Remove the front bulkhead cover (two expansion clips, three clips, and move the right and left fender trims inward).3 CLIPS (Pull straight up.) EXPANSION CLIPS</p> <p>2. 3.</p> <p>SUB HARNESS</p> <p>PANEL RIGHT FENDER TRIM RIGHT FOG LIGHT FOG LIGHT HARNESS LEFT FOG LIGHT 20 A FUSE851210AK</p> <p>FRONT BULKHEAD COVER</p> <p>LEFT FENDER TRIM</p> <p>5202062T</p> <p>2 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>www.collegehillshonda.com4. With the help of an assistant, remove the front bumper (four long clips, four center clips, two socket bolts, and two self-tapping screws). To prevent damage, set the front bumper on a blanket. 6. Install the spring nut onto the front bumper.FRONT BUMPER SPRING NUT SOCKET BOLTS FOG LIGHT COVER OPENING</p> <p>2 SELFTAPPING SCREWS LONG CLIPS CENTER CLIPS LONG CLIPS FRONT BUMPER850904AK</p> <p>SELF-TAPPING SCREW</p> <p>FRONT BUMPER LEFT FOG LIGHT850801AK</p> <p>7. 8. 9.</p> <p>Install the left fog light to the fog light cover opening, and secure it with the self-tapping screw. Repeat steps 5 through 7 on the other side. Route the fog light harness 2-pin connector between the lower grille and the front bumper from the right side through the left side.FRONT BUMPER</p> <p>5.</p> <p>Remove the left fog light cover (four pawls).</p> <p>FRONT BUMPER</p> <p>FOG LIGHT HARNESS 2-PIN CONNECTOR 4 PAWLS FOG LIGHT HARNESS 2-PIN/4-PIN CONNECTORS840301AK</p> <p>LEFT FOG LIGHT COVER</p> <p>FOG LIGHT HARNESS</p> <p>FRONT BUMPER</p> <p>LOWER GRILLE850802AK</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>3 of 12</p> <p>www.collegehillshonda.com10. Attach the clip on the fog light harness to each hole of the lower grille.FOG LIGHT HARNESS LOWER GRILLE FOG LIGHT HARNESS CLIP</p> <p>13. Plug the fog light harness 2-pin connector into the right fog light bulb.FOG LIGHT HARNESS 2-PIN CONNECTOR</p> <p>RIGHT FOG LIGHT BULB</p> <p>WIRE TIE</p> <p>FOG LIGHT HARNESS LOWER GRILLE LOWER GRILLE RIB</p> <p>850903AK</p> <p>14. Install the fog light harness clip onto the lower grille rib. 15. Remove three bolts from the washer resvoir tank.</p> <p>FOG LIGHT HARNESS CLIPS (Attach them to the hole on the lower grille.)</p> <p>850901AK</p> <p>11. Secure the fog light harness to the lower grille with one wire tie. 12. Plug the fog light harness 2-pin connector into the left fog light bulb.</p> <p>LEFT FOG LIGHT BULB</p> <p>3 BOLTS WASHER RESERVOIR TANK852101AK</p> <p>FOG LIGHT HARNESS 2-PIN CONNECTOR</p> <p>850902AK</p> <p>4 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>www.collegehillshonda.com16. Locate the 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the 1-pin connector. Plug the vehicle 1-pin connector you just freed into the sub harness 1-pin connector.SUB HARNESS 1-PIN CONNECTOR VEHICLE HARNESS</p> <p>17. Route the sub harness between the washer reservoir tank and vehicle panel as shown.PIPE</p> <p>SUB HARNESS</p> <p>BLUE TAPE (Remove.) VEHICLE PANEL</p> <p>VEHICLE 1-PIN CONNECTOR</p> <p>SUB HARNESS860601AK</p> <p>WASHER RESERVOIR TANK</p> <p>SUB HARNESS GROUND TERMINAL GROUND BOLT</p> <p>VEHICLE FRAME852910BK</p> <p>18. Secure the sub harness ground terminal to the vehicle frame using the ground bolt supplied. 19. Reinstall the washer reservoir tank. Check that the pipe is installed securely.</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>5 of 12</p> <p>www.collegehillshonda.com20. Secure the sub harness clip to the vehicle frame, and secure the sub harness to the vehicle harness using two wire ties.WIRE TIES SUB HARNESS VEHICLE FRAME</p> <p>23. If equipped, remove the drivers dashboard under cover by turning the knob counterclockwise, and releasing two clips and pin. Take care not to damage the clips.</p> <p>PIN</p> <p>DRIVERS DASHBOARD UNDER COVER CLIP SUB HARNESS 4-PIN CONNECTOR SUB HARNESS CLIP860602BK5202112T</p> <p>2 CLIPS KNOB</p> <p>21. Slide the clip onto the sub harness 4-pin connector, and secure it to the vehicle frame. 22. Plug the fog light harness 4-pin connector to the sub harness 4-pin connector, then reinstall the front bumper.SUB HARNESS 4-PIN CONNECTOR</p> <p>24. Remove the drivers dashboard lower cover (eight clips). Take care not to damage the clips.</p> <p>DRIVERS DASHBOARD LOWER COVER</p> <p>8 CLIPS5202121T</p> <p>FOG LIGHT HARNESS 4-PIN CONNECTOR FRONT BUMPER851201AK</p> <p>6 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>www.collegehillshonda.com25. Lower the tilt lever, and pull the steering wheel toward you. Insert a flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover.COLUMN UPPER COVER STEERING WHEEL (Pull toward you.) 2 RETAINING TABS</p> <p>27. Remove the column lower cover (two self-tapping screws and one screw).</p> <p>Push.</p> <p>COLUMN LOWER COVER</p> <p>HOOKS RETAINING TAB COLUMN LOWER COVER RETAINING TAB SCREW</p> <p>SELF-TAPPING SCREWS5308530T</p> <p>TILT LEVER FLAT-TIP SCREWDRIVER GUIDE5308521T</p> <p>28. Push the retaining tab from the vehicle white 34-pin connector, and raise the lock lever from connector. Remove the connector from the fuse box. Close the lock lever on the vehicle white 34-pin connector and remove the cover by sliding it from the connector.</p> <p>26. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (three retaining tabs). Pull up to remove the column upper cover (two hooks).</p> <p>WHITE 34-PIN CONNECTOR</p> <p>Push. Slide.</p> <p>FUSE BOX</p> <p>COVER Push. RETAINING TAB</p> <p>Push. VEHICLE WHITE 34-PIN CONNECTOR LOCK LEVER</p> <p>851202AK</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>7 of 12</p> <p>www.collegehillshonda.com29. Insert the two switch harness terminals into the white/red terminal and blue terminal of the vehicle white 34-pin connector.WHITE/RED TERMINAL LOCK LEVER RELAY BLUE TERMINAL Harness Side View VEHICLE WHITE 34-PIN CONNECTOR SWITCH HARNESS VEHICLE BRACKET STAY</p> <p>32. Plug the relay into the switch harness relay block, then slide the relay block onto the vehicle bracket stay.</p> <p>SWITCH HARNESS RELAY BLOCK</p> <p>SWITCH HARNESS TERMINALS</p> <p>SWITCH HARNESS5307170T</p> <p>30. Reinstall the vehicle white 34-pin connector. 31. Route the switch harness above the vehicle knee bolster.</p> <p>5307192T</p> <p>33. Locate the 1-pin connector blue-taped to the vehicle harness. Plug the switch harness 1-pin connector into the vehicle 1-pin connector.SWITCH HARNESS</p> <p>VEHICLE KNEE BOLSTER</p> <p>SWITCH HARNESS 1-PIN CONNECTOR</p> <p>SWITCH HARNESS</p> <p>VEHICLE 1-PIN CONNECTOR</p> <p>5307180T</p> <p>5307202T</p> <p>8 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>www.collegehillshonda.com34. Secure the switch harness to the vehicle harness and vehicle knee bolster with three wire ties in the areas shown. 38. Install the new combination light switch on the steering column using the two screws. Hold the case by hand, then install the new combination light switch to the steering column. Do not push on the lever when installing the case. Push in on the case and securely set the retaining tab into the tab hole.COMBINATION LIGHT SWITCH STEERING COLUMN VEHICLE 12-PIN CONNECTOR</p> <p>WIRE TIES</p> <p>VEHICLE KNEE BOLSTER VEHICLE HARNESS</p> <p>TAB HOLE SWITCH HARNESS WIRE TIE</p> <p>5307212T</p> <p>35. Lower the tilt lever and pull the steering wheel toward you.COMBINATION LIGHT SWITCH STEERING COLUMN VEHICLE 12-PIN CONNECTOR COMBINATION LIGHT SWITCH</p> <p>2 SCREWS (Reuse.) CASE RETAINING TAB LEVER851204AK</p> <p>39. Plug the vehicle 12-pin connector to the new switch. Replace the vehicle harness.</p> <p>TAB HOLE</p> <p>SCREWS CASE RETAINING TAB COMBINATION LIGHT SWITCH LEVER STEERING WHEEL</p> <p>851203AK</p> <p>36. Turn the steering wheel 90 counterclockwise. 37. Unplug the vehicle 12-pin connector from the combination light switch. Remove the two screws from the combination light switch. While pushing the retaining tab, slide the combination light switch out, and remove it from the steering column. Do not pull on the lever when removing the case. Do not damage the tab hole of the steering column.9 of 12</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>www.collegehillshonda.com40. Install the 20 A fuse into the fuse box in the location shown. If the fuse is already installed, it is not necessary to install the 20 A fuse. USE AND CARE How to Operate Fog Lights Turn the light switch to the low beam). position (headlights on</p> <p> Turn the fog light switch (indicator is on).</p> <p>FUSE BOX FUSE BOX HEADLIGHT SWITCH OFF Low FOG LIGHT SWITCH OFF High -</p> <p>20 A FUSE</p> <p>ON</p> <p>ON</p> <p>FUSE LOCATION 65307240T</p> <p>871716BK</p> <p>41. Check that all wire harnesses are routed properly and all connectors are plugged in. 42. Reinstall all removed parts. 43. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. 44. Enter the anti-theft codes for the audio system and the navigation system (if equipped), and reset the radio station presets. 45. Reset the clock on vehicles without navigation.</p> <p>NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Adjusting the Aim 1. Adjust the vertical aiming according to local laws and regulations. To adjust, turn the adjusting screw in or out until the correct angle is obtained.</p> <p>ADJUSTING SCREW</p> <p>To lower. To raise.</p> <p>851205AK</p> <p>2.</p> <p>Repeat on the right side.</p> <p>10 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>www.collegehillshonda.comBULB REPLACEMENT 1. Remove the self-tapping screw, and pull the fog light out toward you. 3. Remove the bulb from the fog light by turning it.FOG LIGHT</p> <p>SELFTAPPING SCREW</p> <p>BULB FOG LIGHT851206AK 851208AK</p> <p>2.</p> <p>Push in the retaining tab, and unplug the connector from the fog light.</p> <p>RETAINING TAB (Push.)</p> <p>CONNECTOR LEFT FOG LIGHT851207AK</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p> <p>AII 40362 (0808)</p> <p>11 of 12</p> <p>www.collegehillshonda.com4. Install a new bulb on the fog light by turning it clockwise until it stops. Take extreme care when replacing the fog light bulb to avoid damaging the lenses or finished surfaces of the body. Use only a Honda Genuine halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers.</p> <p>Turn the bulb until it stops.</p> <p>CONNECTOR</p> <p>FOG LIGHT</p> <p>NEW BULB851209AK</p> <p>5. 6. 7.</p> <p>Plug the connector to the bulb. Install the fog light in the reverse order of removal. Check that the bulb comes on properly. Adjust the aim as necessary.</p> <p>12 of 12</p> <p>AII 40362 (0808)</p> <p> 2008 American Honda Motor Co., Inc. All Rights Reserved.</p>