fm2000a amplifier package user's manual · fm2000a user’s manual. i. 1–2. 1.1 your...
TRANSCRIPT
i
FM2000AAmplifier Package
User's Manual
©2005 Crown Broadcast, a division of International Radio and Electronics, Inc.25166 Leer Drive, Elkhart, Indiana, 46514-5425 U.S.A.
(574) 262-8900
ii
Revision ControlRevision Print Date
Initial Release (Rev. 0) 900415-1 November 1998
Second Printing 130319-1 November 1999
Third Printing April 2002
Important Notices©2005, Crown Broadcast, a division of International Radio and Electronics, Inc.
All rights reserved. No part of this publication may be reproduced, transmitted,transcribed, stored in a retrieval system, or translated into any language in anyform by any means without the written permission of Crown International, Inc.
Printed in U.S.A.
Crown attempts to provide information that is accurate, complete, and useful.Should you find inadequacies in the text, please send your comments to thefollowing address:
International Radio and Electronics25166 Leer Drive, P.O. Box 2000
Elkhart, Indiana, 46515-2000 U.S.A.
iii
ContentsContentsContentsContentsContentsSection 1—Getting Acquainted1.1 Your Amplifier Package ..................................................................................... 1-21.2 Amplifier Package Specifications ...................................................................... 1-31.3 Safety Considerations ....................................................................................... 1-41.3.1 Dangers ........................................................................................................ 1-41.3.2 Warnings ...................................................................................................... 1-41.3.3 Cautions ....................................................................................................... 1-4
Section 2—Installation2.1 Operating Environment .....................................................................................2–22.2 Tools Required ..................................................................................................2–22.3 Unpacking .........................................................................................................2–22.4 Preinstallation ...................................................................................................2–32.4.1 Power Amplifier Modules .............................................................................2–32.4.2 Hubble Twist Lock® Connector Wiring ........................................................2–42.5 Installation ........................................................................................................2–52.6 Remote I/O Connection .....................................................................................2–6
Section 3—Operation3.1 Initial Power-up Procedures..............................................................................3–23.2 Power Switches ................................................................................................3–43.2.1 AC Input Circuit Breaker ...............................................................................3–43.2.2 DC Power Switch ..........................................................................................3–53.2.3 Interlock Switch ............................................................................................3–53.3 Digital Multimeter .............................................................................................3–63.4 Fault Indicators .................................................................................................3–73.5 Fuse Indicators .................................................................................................3–8
Section 4—Principles of Operation4.1 PA2000 Power Amplifier ...................................................................................4–24.1.1 Power Modules ............................................................................................4–24.1.2 Power Combiner Board ................................................................................4–24.1.3 Backplane Assembly .....................................................................................4–34.1.3.1 Backplane DC Interconnect Board ........................................................4–34.1.3.2 Input Divider Board ...............................................................................4–34.1.3.3 Output Combiner Board ........................................................................4–34.1.4 Output Filter & Reflectometer .......................................................................4–34.1.5 Metering and Control Board .........................................................................4–44.1.6 DC Fuse and Power Distribution Board ........................................................4–44.1.7 Cooling Fans .................................................................................................4–4
iv
4.2 PS2000 Power Supply ...................................................................................... 4–54.2.1 AC Input Board ............................................................................................. 4–54.2.2 PFC (Power Factor Correcting) Switching Board .......................................... 4–54.2.3 DC Output Board .......................................................................................... 4–64.2.4 Cooling Fans ................................................................................................. 4–6
Section 5—Troubleshooting5.1 Troubleshooting Flow Chart Analysis ................................................................ 5–25.2.1 In Ref (Input Drive Reference) ...................................................................... 5–35.2.2 SWR (Standing Wave Ratio) ........................................................................ 5–35.2.3 ALC (Automatic Level Control) ..................................................................... 5–35.2.4 Power Out .................................................................................................... 5–35.2 Digital Multimeter Parameters .......................................................................... 5–35.2.5 PA Temp ....................................................................................................... 5–45.2.6 PA Voltage .................................................................................................... 5–45.2.7 Tot Current ................................................................................................... 5–45.2.8 PA1–8 ........................................................................................................... 5–45.3 Fault Indicators ................................................................................................. 5–55.3.1 Antenna ........................................................................................................ 5–55.3.2 RF Drive ........................................................................................................ 5–55.3.3 PA Temp ....................................................................................................... 5–55.3.3.1 Potential Causes for Non-functioning Cooling Fans .............................. 5–55.3.4 PA DC ........................................................................................................... 5–65.3.5 Multiple Indicators........................................................................................ 5–6
Section 6—Reference Drawings6.1 Views ................................................................................................................ 6–26.2 Diagrams and Schematics ................................................................................ 6–3
Section 7—Service and Support7.1 Service .............................................................................................................. 7–27.2 24–Hour Support .............................................................................................. 7–27.3 Spare Parts ....................................................................................................... 7–2
Glossary
Index
Getting Acquainted 1–1
IINFORMATION
Section 1—Getting Acquainted
This section provides a general description of the FM2000Apower amplifier system and introduces you to safety conventionsused within this document. Review this material before install-ing or operating the amplifier and power supply.
FM2000A User’s Manual
I
1–2
1.1 Your Amplifier Package
The FM2000A is a highly efficient amplifier package designed to set a new standardin FM transmitter design offering modularity, ease of use, and long-term reliabil-ity. The FM2000A package includes a PA2000 amplifier, PS2000 power supply, andan FM2K accessory pack.
The PA2000 broadband amplifier requires no tuning and typically provides 80% RFefficiency across the band. The PS2000 power supply is power factor corrected and90% efficient. Modern MOSFET technology ensures high AC to RF efficiency(better than 70% overall) and long-term reliability. The unmatched efficiency ofthis power amplifier significantly improves your bottom line by providing cooleroperation and lower power costs.
These modular units are uniquely designed to be lightweight and compact forconvenient shipping, and require only seven RU spaces for installation. Installa-tion is made simple with just three interconnections between the amplifier andpower supply. In addition, built-in digital metering and status indicator capabili-ties enable intuitive operation to further augment the user-friendly design.
Economic long-term reliability is ensured through our carefully engineered solid-state design. The PA2000 features four field-replaceable 500–watt power modules.
This power amplifier delivers 500 to over 2000 watts of RF power output. Use yourexisting exciter or purchase the FM2000T which includes our award-winningFM100 exciter for an unbeatable 2 kW transmitter package.
Illustration 1–1 FM2000A Amplifier Package
Fault
AntennaRF DrivePA TempPA DC
PA1PA2PA3PA4
PA5PA6PA7PA8
Power OutPA TempPA VoltageTot CurrentALC
SWRIn Ref
Metering
PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8
Fuses
®
®
Power
I
O
Getting Acquainted 1–3
1.2 Amplifier Package SpecificationsRF Power Output: 200 to 2200 watts continuous with controlled
power adjust, with remote controlled powercapability
RF Drive Requirement: 50-70 watts for full output
RF Output Impedance: 50 watts (unbalanced)
Maximum SWR: 1.7:1 (With power foldback at high SWR)
Frequency Range: 87–108 MHz
RF Harmonics/Spurious Products: Better than –80 dB
Asynchronous AM S/N Ratio: Better than 55 dB with 100% modulation @400 Hz, no de-emphasis, no FM modulation(typically > 60 dB)
Synchronous AM S/N Ratio: Better than 55 dB with 100% modulation @400 Hz, no de-emphasis, FM modula-tion = 75 kHz @ 400 Hz (typically > 60 dB)
Operating Environment:
Temperature Range: 0°–50°C at sea level
Humidity Range: 0–80% at 20°C, noncondensing
AC Power: 240 volts AC +10/-15%, 50–60 Hz
Power Consumption: 2800 watts at 2000 watts RF output typical
Power Factor: .96 typical
Overall Efficiency: 70% typical
RF Output Connector: 7/8 inch EIA flange, 7–16 inch DIN optional
Power Amplifier Chassis: 7 x 17.25 x 23 inches (17.78 x 43.82 x58.42 cm) exclusive of rack ears, butinclusive of connectors
Power Supply Chassis: 5.25 x 17.25 x 23 inches(13.34 x 43.82 x 58.42 cm)exclusive of rack ears
Weight: PA2000—57.5 pounds (26.1 kg)RF PA Modules —8 pounds (3.6 kg) eachPS2000—43 pounds (19.5 kg)
Note: System performance is specified using Crown BroadcastModel FM100 Exciter where applicable.
FM2000A User’s Manual
I
1–4
1.3 Safety Considerations
Crown Broadcast assumes the responsibility for providing you a safe product andsafety guidelines during its use. “Safety” means protection to all individuals whoinstall, operate, and service the transmitter as well as protection of the transmitteritself. To promote safety, we use standard hazard alert labeling on the product andin this manual. Follow the associated guidelines to avoid potential hazard.
1.3.1 DangersDANGER represents the most severe hazard alert. Extreme bodily harm or deathwill occur if DANGER guidelines are not followed.
1.3.2 WarningsWARNING represents hazards which could result in severe injury or death.
1.3.3 CautionsCAUTION indicates potential personal injury or equipment or property damage ifthe associated guidelines are not followed. Particular cautions in this text alsoindicate unauthorized radio-frequency operation.
Illustration 1–3 Sample Hazard Alert
Severe shock hazard!
Turn power off andwait approximately 1minute for capacitorsto discharge beforehandling them.
WARNINGType of Hazard
Pictorial Indicationof Hazard
Explanationof Hazard
2–1Installation
Section 2—Installation
This section provides important guidelines for installing yourpower amplifier and power supply. Review this information care-fully for proper installation.
®
2–2 FM2000A User’s Manual
2.1 Operating EnvironmentYou can install the FM2000A amplifier system in a standard 19–inch componentrack or on a suitable surface such as a bench or desk. In any case, the area shouldbe as clean and well-ventillated as possible. The power supply must be installeddirectly above or below the power amplifier (for the included dressed cables toreach their respective connectors).
2.2 Tools RequiredTo install the power supply and power amplifier, you will need the following tools:
Medium phillips screwdriver
Medium flat-blade screwdriver
Small flat-blade screwdriver
7/16–Inch wrench or nut driver
ESD (Electrostatic Discharge) protection grounding strap and/or mat.
2.3 UnpackingBefore handling any exposed printed circuit boards, ground yourself with anantistatic strap and/or mat.
The power amplifier, power supply, and two power amplifier modules are packedand shipped in individual boxes because of their modular nature. (The FM2Kaccessory kit is packed inside one of the two power amplifier module boxes.) Foradded protection, both the PA2000 amplifier and PS2000 supply are packed in aninner box and then placed inside an outer box with styrofoam protective corners inboth boxes. You will need to unpack a total of four boxes (plus two inner boxes).
Note: Save the boxes and packaging material that the individualunits are packed in should you need to return them for factoryservice.
CAUTIONPossible equipment damage!Guard against electrostatic dischargethrough electronic components.
2–3Installation
2.4 Preinstallation
2.4.1 Power Amplifier ModulesThe PA2000 incorporates four power amplifiers (two each in two modules). Due topossible damage during shipment, the power modules have been removed. Followthese steps to install the modules:
1. Remove the front panel of the PA2000 (four screws).
2. Taking ESD precautions (see page 2–2), unpack the power modules and placethem on your work area with the circuit sides up.
3. The warning labels on the front of the modules should all be positioned to thecenter of the chassis, also note the position of the connector on the modulesand in the chassis.
4. Insert the four power modules, using their slide rails, into the built in chan-nels of the right-side cavity and two (upside down) in the left cavity as shownbelow. Note that the connectors and warning labels are nearest the middlewall or partition of the PA2000.
Illustration 2–1 Power Amplifier Module
5. Be sure the modules are pushed in completely so that the connector makesproper contact.
6. Replace the front panel of the PA2000.
Illustration 2–2 Power Amplifier Module Placement
Middle Partition
Module B(amps 3 & 4)
Module D(amps 7 & 8)
Connector
Slide Rail
Warning Label
Module A(amps 1 & 2)
Module C(amps 5 & 6)
2–4 FM2000A User’s Manual
WARNING
2.4.2 Hubble Twist Lock® Connector Wiring
Prepare the wiring for the Hubble Twist-Lock® connector in the following mannerbefore connecting to your AC power source:
1. Use round cord with a diameter of 0.385–0.780 inches (10–20 mm), Type SJ12/3 – 10/3; Type S 16/3 – 10/3.
2. Select conductor size from your National Electrical Code®.
3. Slide the cover onto the cord. Remove insulation from cable and conductorsas shown in Illustration 2–3. Do not tin conductors.
5. Tighten terminal screws to 18 pound•inches (2.1 N•m) of torque.
6. Tighten assembly screws to 10 pound•inches (1.1 N•m) of torque.
7. Tighten cord clamp screws to 10 pound•inches (1.1 N•m) of torque.
Terminal
Green Hex Head Screw Equipment grounding conductor(green or green/yellow)
Conductor
Brass Screw Hot circuit conductor, 240 VAC(NOT white, NOT green)
Brass/Black Screw Hot circuit conductor, 240 VAC(NOT white, NOT green)
4. Loosen terminal screws. Insert conductors fully into proper terminals ac-cording to the table below. Take caution that there are no stray wire strands.
Illustration 2–3 Cover, Cable & Conductors
1 Inch(25 mm)
5/8 Inch(16 mm)
Possible Electric Shock Hazard!
Do not connect AC source until allother connections are made andinstallation is complete.
2–5Installation
2.5 Installation1. Mount the units in an appropriate 19–inch wide cabinet. The power supply
must be installed directly below the power amplifier for the included cablesto reach their respective connectors (see illustration 2–4 below).
Note: The PS2000 weighs approximately 43 pounds (19.5 kg); thePA2000, approximately 57.5 pounds (26.1). Use help to install.
2. Ensure that the PS2000 power switch is off, the circuit breakers of the 240VAC source on the back panel are off, and the AC connector is not plugged in.
3. Install the exciter source (such as a Crown Broadcast FM100) according to itsinstructions.
4. Connect the RF input cable from the exciter source to the N connector on theback of the PA2000.
5. Connect the RF output cable (from the antenna) to the 7/8 EIA or 7-16 DINconnector on the back of the PA2000.
6. Connect one end of the supplied control cable to the 9–pin D-sub connectoron the PA2000.
7. Connect the other end of the control cable to the 9–pin D-sub connector onthe PS2000.
Illustration 2–4 Rear Panel Connections
RF Input
Remote I/O
Control
RF Monitor(Optional Connection)
RF Output
Circuit Breakers
+ DC Input
DC Input
+ DC Output
DC Output
Air Intakes/Filters
FansPower
Control
OFF OFF
240 VAC IN
PA2000
PS2000
Ground Screws
Air Exhaust Vents
2–6 FM2000A User’s Manual
8. Using the supplied connector, tie together pins 6 and 7 of the Remote I/Oconnector. The amplifier will not operate without this connection or aremote switch on these pins. (See Section 2.6 for Remote I/O connection.)
9. If monitoring of the output signal is desired, connect the RF monitor cable tothe BNC connector on the PA2000.
10. Connect the DC input/output cables between the PA2000 and the PS2000 asillustrated (Illustration 2–4). The connector end with the ground lead con-nects to the PA2000. Be sure to attach the ground leads as indicated.
Note: The power lead shield is only grounded at the PA chassis.
11. Install the covers over the DC terminals of the PA2000 and the PS2000 usinghardware form the hardware kit (1/4–inch X 6–32 bolts with lock washers).
12. Connect to your AC power source by inserting the Hubble Twist-Lock connec-tor into the female Hubble connector on the PS2000 and turn to the rightuntil the connection locks.
2.6 Remote I/O ConnectionThe Remote I/O Connector on the back of the PA2000 allows remote control andmonitoring of Certain transmitter functions. There are three basic control func-tions—AC on/off, RF power level adjustment, and RF down/off.
The AC power on/off remote control function, available at pin 7 of the Remote I/OConnector, turns DC power to the PA on when the pin is grounded.
The RF power level adjustment remote control function has an internal maximumlimit set on the Metering and Control Board. The Local Power Adjust (R62) setsthe maximum limit of RF power output. The limit is set by placing the Remote/Local switch (SW5) in the LOCAL position and adjusting the Local Power Adjust toyour desired maximum limit (see illustrations 2–5 and 2–6). However, for anyremote operation to work, the Remote/Local slide switch must be in the REMOTEposition. Then the on-board remote RAISE and LOWER push buttons and anyexternal remote switches attached to pins 4 and 15 of the I/O Connector can adjust
LOCAL
MAXIMUM
+5V
LOCALPOWERADJUST
MINIMUM
REMOTE
TANSMITTERCONTROL
SW3RAISE
SW4LOWER
SW5
R62
Electro-ControlCircuit
REMOTERAISE POWER
Pin 4Remote I/O Conn.
REMOTELOWER POWER
Pin 15Remote I/O Conn.
Illustration 2–5 Local and Remote Functions
2–7Installation
For remote I/O (Input/Output) connection, connect your remote I/O cable fromyour remote control location to the 25–pin (female) D-sub connector on the backpanel of the PA2000. The I/O Connector on the power amplifier is described in thefollowing diagram:
Illustration 2–7 Remote I/O connector (back panel view)
Illustration 2–6 On-board Remote Power & Related Controls
Local/RemoteSlide Switch
On-board RemotePower Adjust
Buttons
Local Power AdjustPot
Another remote control function, available at pin 5 of the Remote I/O Connector,turns RF down/off. Connecting this pin to ground through a resistor allows theRF power output level of the amplifier to be reduced below the internal limit set bythe Local Power Adjust pot or the remote Raise/Lower settings. However, somedrive power, less than one watt, may still be present at the antenna. Depending onthe resistor used, this pin can serve as a control for optional low power operation.
The remaining remote functions are for monitoring the various parametersof the PA2000. They are either buffered metering outputs, direct reading, orlatched high/low indications. Further details of these functions are described inthe pin-out table on page 2–8.
Note: If Remote I/O controls are not used, tie pin 7 to pin 6 (GND.).
the level up to that limit and down to zero. When a specific output power level isset, the Metering and Control Board controls and maintains the setting to keep thepower constant. The location of the Local Power Adjust (R62), the on-board Raiseand Lower switches (SW3 & SW4), and the Local/Remote slide switch (SW5) areshown below.
25 14
13 1
The Remote I/O Connector Pinout Table on the next page summarizes the RemoteI/O pin connections.
2–8 FM2000A User’s Manual
Remote I/O Connector Pinout Table
Pin # Function
1 PA#8 Current Monitor (a buffered metering output with 1 V = 2 A)
2 PA#7 Current Monitor (a buffered metering output with 1 V = 2 A)
3 Ground
4 Remote RAISE Power (a momentary switch, on this pin, when held low willraise the power level 10 watts every 0.5 seconds)
5 Remote RF Power Control (a resistor to ground on this pin reduces RFpower output level below internal limits. See Section 2.6, page 2–7)
6 Ground
7 Remote AC Power On (a latching switch, on this pin, when held low will turnthe AC power supply on)
8 Fault Summary (the voltage from this pin goes to +5 V if any fault occurs anddrops below 2V when the fault goes away)
9 Ground
10 ALC (the voltage from this pin is a direct reading of automatic level controlvoltage, not buffered)
11 PA Temperature (a buffered metering output with 1 V = 20° C)
12 SWR (a buffered metering output with a calculated reading of standing waveratio in VDC)
13 RF Output Power (a buffered metering output with a calculated reading ofoutput power of 1 V = 1000 W)
14 Input Power Reference (a buffered metering output with a DC voltagerepresenting input power)
15 Remote LOWER Power (a momentary switch, on this pin, when held low willlower the power level 10 watts every 0.5 seconds)
16 PA#6 Current Monitor (a buffered metering output with 1 V = 2 A)
17 PA#5 Current Monitor (a buffered metering output with 1 V = 2 A)
18 Ground
19 PA#4 Current Monitor (a buffered metering output with 1 V = 2 A)
20 PA#3 Current Monitor (a buffered metering output with 1 V = 2 A)
21 Ground
22 PA#2 Current Monitor (a buffered metering output with 1 V = 2 A)
23 PA#1 Current Monitor (a buffered metering output with 1 V = 2 A)
24 PA Total Current Monitor (a buffered metering output with 1 V = 20 A)
25 PA Volts (a buffered metering output with 1 V = 10 V)
Note: PA = Power Amplifier
3–1Operation
Section 3—Operation
This section provides general operating parameters of yourpower amplifier system and a detailed description of the frontpanel display.
3–2 FM2000A User’s Manual
These steps summarize the operating procedures you should use for the initialoperation of the power amplifier and power supply of the FM2000A.
1. Ensure that the external remote control unit is properly connected (SeeSection 2.6 and the pin-out description table on page 2–8 for proper pinconfiguration). If not using a remote control unit, pin 7 must be tied toground pin 6.
2. Connect Antenna.
3. If using an external remote control, enable the power supply via the remoteI/O connector.
4. Turn on (set to up) the AC input circuit breaker located on the rear panel ofthe power supply (do not turn on the front panel power switch yet).
3.1 Initial Power-up Procedures
5. Turn on the exciter (a Crown FM100 or equivalent) and adjust its RF poweroutput level until the In Reference (In Ref) voltage, as indicated on the PA2000front panel Digital Multimeter, is between 0.8 and 1.2 volts. This is not a drivedependent amplifier; therefore drive must be at a constant level regardless ofmain output power.
Note: The unit will not operate until the exciter is active and produces sufficient drive.
Illustration 3–1 PS2000 Back Panel Functions
240 VAC IN
AC InputCircuit Breaker
Outputs toPA1000
Air Exhaust Vents
+ DC Output
DC Output
PS2000
FansPower
Control
OFF OFF
FanCircuit Breaker
3–3Operation
Illustration 3–3 PS2000 Front Panel Functions
7. Turn on the main power switch located on the front panel of the power supply.(The unit typically takes 30 seconds to power up.)
8. Check the PA2000 parameters with the Digital Multimeter for a current (TotCurrent) of 42 to 48 amps and a voltage (PA Voltage) of 32 to 36 volts. Ifparameters are within range, increase the Local Power Adjust to the maximumlevel of desired operation.
Note: The Local Power Adjust pot is unconventional (CW lowers power).
6. Before power-up, place the Local/Remote switch (located on the Metering &Control board behind the front panel) in the Local position and adjust theoutput power limit to the mid-level position using the Local Power Adjust,also on the Metering & Control board (see Illustration 3–2 below). The unit isnormally shipped with this setting. See Section 2.6 for setting up remoteoperation and using the on-board remote buttons and other controls.
Illustration 3–2 Local Power Adjust and Other Controls
®
Power
I
O
Power Switch
Air Intakes/Filters
Local/RemoteSlide Switch
On-board RemotePower Adjust
Buttons
Local Power AdjustPot
3–4 FM2000A User’s Manual
3.2.1 AC Input Circuit BreakerThe PS2000 supplies power to the PA2000 by converting single-phase 220/240 VACinto 50 VDC. The PS2000 is protected by a 20 A, double-pole circuit breakerlocated on the rear panel. This AC input circuit breaker must be in the “up”position (as shown below) for operation.
3.2 Power Switches
Illustration 3–4 AC Input Circuit Breaker
9. Place the Local/Remote switch (see Illustration 3–2) in the Remote positionand, using an external remote control unit connected to the Remote I/Oconnector or the on-board remote Raise/Lower buttons, adjust the PA2000 tothe maximum power set by the Local Power Adjust. (This prevents adjustingto higher than permitted power levels.)
10. Verify that the following conditions are present as indicated by the PA2000’sDigital Multimeter:
a. In Ref—Should read between 0.4 and 0.8 volts (0.5 nominal, dependentupon power input level).
b. SWR—Should read 1.05 to 1.5.c. ALC—Should read between 4.00 and 6.00 volts for 2.2 kW output (less
for lower output or danger conditions, i.e. high SWR).d. Power Out—Should read 2.20 for 2.2 kW output.e. PA Temp—Should read 35 to 50°C with ambient temperature of 25°C.
The remainder of this section describes the functions of the front and rear panelindicators and switches of the PA2000 and PS2000.
240 VAC IN
FansPower
Control
AC InputCircuit Breaker
ONON
3–5Operation
3.2.2 DC Power SwitchThe main on/off power switch located on the front panel of the power supplycontrols high voltage output. (The control circuit activates this voltage.)
Illustration 3–5 DC Power Switch
Illustration 3–6 Interlock Switch
Interlock Switch
®
Power
I
O
Power Switch
WWARNINGARNING Lethal voltages are still present on the AC Input Board !So, handle with care.
3.2.3 Interlock SwitchThis switch is located on the fan mounting bracket in the power supply. When thetop cover of the power supply is removed, the Interlock Switch interrupts the powersupply control circuit disabling the high and low voltage supplies.
3–6 FM2000A User’s Manual
3.3 Digital Multimeter
Illustration 3–7 Digital Multimeter
The 3–digit numeric display in the upper left corner of the front panel providesinformation on the amplifier’s operation. Use the “up” and “down” push-buttons toselect one of the following parameters as indicated by a green LED.
In Ref—Input reference is a relative voltage level used to determine input RFpower level. This varies between frequency of operation and input power level.
SWR—Direct reading of the antenna Standing-Wave Ratio (the ratio of the actualload impedance to the desired 50 ohm load impedance).
ALC—Automatic level control is DC gain control bias used to regulate PA supplyvoltage. With the PA power supply at full output voltage, ALC will read about 6.0volts. When the RF output is being regulated by the RF power control circuit, thisvoltage will be reduced, typically reading 5.0 to 6.0 volts. The ALC voltage will bereduced during PA DC overcurrent, SWR, or overtemperature conditions.
Power Out—Actually reads RF voltage squared, so the accuracy can be affected bySWR. Tolerance of ± 10% is normal. For exact set-up on site, an external powermeter is recommended.
PA Temp—Highest temperature of all individual RF power amplifier heatsinks indegrees C.
PA Voltage—Supply voltage of the RF power amplifier.
Tot Current—Sum total current of all individual RF power amplifiers in amperes.
PA1–8—Individual RF amplifier current reading in amperes.
Fault
AntennaRF DrivePA TempPA DC
PA1PA2PA3PA4
PA5PA6PA7PA8
Power OutPA TempPA VoltageTot CurrentALC
SWRIn Ref
Metering
PA1 PA2 PA3 PA4
®
Multimeter Metering Selection Buttons Metering Indicators
3–7Operation
3.4 Fault Indicators
Illustration 3–8 Fault Indicators
CAUTIONPossible equipment damage!
Do not exceed 80 watts of input drive.Damage to the PA2000 will result ifthis level is exceeded.
Faults are indicated by illuminated red LED’s when the following occurs:
Antenna—Load SWR exceeds 1.5:1. ALC voltage is reduced to limit the reflectedRF power.
RF Drive—Lack of or insufficient RF drive. If the RF drive fault LED is lit, inputdrive must be increased. To achieve full output power, 70–80 watts of input drive isrequired.
PA Temp—PA heatsink temperature is greater than 75°C (power foldback will beginat this point).
PA DC—Power supply current for the PA (power amplifier) is at the preset limit, orthere is a difference of more than 2.5 amps in current between the individual PAs.When this indicator is on ALC, the voltage is reduced automatically which holds thesupply current to the preset limit.
Fault
AntennaRF DrivePA TempPA DC
PA1PA2PA3PA4
PA5PA6PA7PA8
Power OutPA TempPA VoltageTot CurrentALC
SWRIn Ref
Metering
PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8
Fuses
®
Fault Indicators
3–8 FM2000A User’s Manual
3.5 Fuse Indicators
Illustration 3–9 Fuse Indicators
The PA2000 consists of four field-replacable power modules with two amplifiers ineach module. If a module fails, it may be replaced while the unit continues tooperate (at a reduction in output power).
Each of the paralleled amplifiers is protected by a 10 ampere fast-acting fuse.When a fuse opens, the indicator light next to it comes illuminates and built-inredundancy allows the unit to continue operation. The fuse can be replaced whilethe unit is operating. Fuses 1 and 2 represent amplifiers 1 and 2 on the top leftmodule. Fuses 3 and 4 represent amplifiers 3 and 4 on the top right module. Fuses5 and 6 represent amplifiers 5 and 6 on the lower left power module. Fuses 7 and 8represent amplifiers 7 and 8 on the lower right power module.
Fault
AntennaRF DrivePA TempPA DC
PA1PA2PA3PA4
PA5PA6PA7PA8
Power OutPA TempPA VoltageTot Current
PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8
Fuses
fi
Fuses and Indicators
4–1Principles of Operation
in questo mondo, erono due persone che abbiano
forse, uno si dice che non ha la dispozione do farlo. M
se diciamo che che non c'e nulla nel mondo reale di
ma scrivendo con la matita ci insegna a non parlare
in questo mondo, erono due persone che abbiano
forse, uno si dice che non ha la dispozione do farlo. M
se diciamo che che non c'e nulla nel mondo reale di
ma scrivendo con la matita ci insegna a non parlare
ma scrivendo con la matita ci insegna a non parlare
in questo mondo, erono due persone che abbiano
forse, uno si dice che non ha la dispozione do farlo. M
se diciamo che che non c'e nulla nel mondo reale di
ma scrivendo con la matita ci insegna a non parlare
ma scrivendo con la matita ci insegna a non parlare
in questo mondo, erono due persone che abbiano
forse, uno si dice che non ha la dispozione do farlo. M
se diciamo che che non c'e nulla nel mondo reale di
ma scrivendo con la matita ci insegna a non parlare
se diciamo che che non c'e nulla nel mondo reale di
ma scrivendo con la matita ci insegna a non parlare
Section 4—Principles of Operation
This section discusses the circuit principles upon which thepower amplifier and power supply function. This information isnot needed for day-to-day operation, but may be useful for ad-vanced users and service personnel.
in questo mondo,forse, uno si dicese diciamo che
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dice
se diciamo che
ma scrivendo con
se diciamo che
ma scrivendo con
4–2 FM2000A User’s Manual
IntroductionThe FM2000A is a solid state RF amplifier package designed to deliver 500 to 2000watts. The package consists of two separate, compact units—a power supply(PS2000) and a power amplifier (PA2000). In turn, these units consist of modularcomponents which provide for efficient operation as well as ease-of-service.
4.1 PA2000 Power AmplifierThe PA2000 power amplifier features adjustable output to deliver 500–2000 watts ofRF output power for broadcast transmission. The amplifier is broadband; no tuningis required. The design, however, ensures efficient operation. Typical RF efficiencyis 75% to 85% across the FM band.
4.1.1 Power ModulesThe primary components of the PA2000 are four, 500–watt power modules. Thesepower modules are mounted by stacking two in the left cavity and two in the rightcavity of the chassis.
The chassis of the power modules acts as a heat sink for the MOSFET amplifiers.There are two power amplifiers mounted to spacer plates on each of the heat sinks,for a total of eight power amplifiers in all. (The power amplifiers are the same asthose utilized in the Crown Broadcast 100, 250, 500, and 1000–watt transmitters.)
Power from the amplifiers is combined through a micro-strip combiner to convertfrom 50 Ω output impedance for each amplifier to an intermediate impedance andthen return to the 50 Ω output at the Low Pass Filter. This technology eliminatestuning and adjustments throughout the 88–108 FM band and enables each amplifierto equally share the power load. The power combiner is also designed to allow amodule to be disconnected from the combiner and removed without adverselyaffecting the impedance balance of the unit. With one module removed the imped-ance change allows the remaining modules to continue operation at approximatelythree-fourths of the full output power.
4.1.2 Power Combiner BoardThere are four Power Combiner Boards; one attached to each of the four heatsinksoverlapping the amplifiers. Each board takes the power from two amplifiers andcombines it through a parallel quarter-wave transmission line transformer network.The power is then summed in a common point junction on the Output CombinerBoard.
4–3Principles of Operation
4.1.3 Backplane AssemblyThe backplane assembly is located in the vertical center of the PA2000 behind thefour power modules. The Backplane Assembly is the common connection point forthe major sections of the transmitter. This assembly consists of the Input DividerBoard, Output Combiner Board, and a Backplane Interconnect Board.
4.1.3.1 Backplane DC Interconnect Board
This board is located nearest the metal inner brace of the chassis. It distributes DCpower to each of the four MOSFET amplifiers, provides the interconnections forcontrol of the power supply, and enables connection to the remote control inter-face. The Backplane/DC Interconnect Board contains interconnections from theControl and Metering Board to the DC Fuse and Power Distribution Board, as wellas power connections to the power amplifier modules.
4.1.3.2 Input Divider Board
The Input Divider Board is the middle board sandwiched between the Backplane DCInterconnect Board and the Output Combiner Board. It provides the power divisionand impedance transformation needed to supply proper drive to each of the eightamplifiers.
4.1.3.3 Output Combiner Board
The Output Combiner Board is located nearest the Output Filter It consists of amicro-strip transmission line that combines the output power from the four poweramplifier modules so that ultimately, all the power comes together at one commonpoint junction. Here the currents and voltages of all four power amplifier modulesare in phase and producing equal RF output power. From this common pointjunction, the Output Combiner Board uses a second quarter-wave transformer toconvert the output power to the 50–ohm impedance needed at the output of theunit.
4.1.4 Output Filter & ReflectometerThe Output Filter/Reflectometer is located behind the Backplane Assembly in thecenter of the PA2000. See the accompanying schematic in Section 6 for moreinformation.
The ninth-order, elliptic, low-pass filter attenuates harmonics generated in thepower amplifier. The capacitors for the filter are circuit board pads. The reflecto-meter uses printed circuit board traces for micro-strip transmission lines. Trans-mission line segments (with an impedance of about 100 ohms) on either side of a50–ohm conductor provide sample voltages representative of the square root offorward and reverse power. DC voltages, representative of forward and reflectedpower, go through a bulkhead Filter Board to the Backplane/DC InterconnectBoard, then to the Metering Board where they are processed for power control andmetering and for SWR metering and protection.
in questo mondo,forse, uno si dicese diciamo che
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dice
se diciamo che
ma scrivendo con
se diciamo che
ma scrivendo con
4–4 FM2000A User’s Manual
4.1.5 Metering and Control BoardThe Metering and Control Board is located above the upper left cavity. This boardsupplies readings of voltages and currents, and provides information on the opera-tion of the amplifier.
The Local Power Adjust pot sets the upper limit (maximum) of RF power output.The on-board RAISE and LOWER push buttons and any external remote control ofthe power level is activated within that limit by placing the Local/Remote slideswitch on the board into the Remote position. When a specific output power is set,the Metering and Control Board controls and maintains the setting keeping powerconstant. A long-life battery supplies power to retain the power setting after theamplifier is turned off.
This board also takes samples from the RF amplifier boards and PS1000 powersupply and processes all the data. It provides SWR readings from the Output Filterand folds back the amplifier power if the SWR exceeds safe operating limits. Protec-tion circuitry for overcurrent and overtemperature conditions is designed into thisboard as well, providing additional precaution against overheating. This board isfail-safe, like all the other circuit board components in the FM2000A and can beremoved for repair/replacement if necessary.
4.1.6 DC Fuse and Power Distribution BoardThis board is located above the right cavity over Power Modules A and B. The DCFuse and Power Distribution Board takes power direct from the power supplythrough one 80–amp power line, divides it into eight separate DC power lines, anddistributes it to the eight power amplifiers. Metering resistors in each of the eightpower lines monitor the current drawn by each of the eight amplifiers to ensureproper function for monitor and control of the unit.
4.1.7 Cooling FansThere are two cooling fans located in the back of the PA2000 powered by thePS2000. The fans operate at 24 volts and is rated at 235 cubic feet per minute.Cool air is drawn through the heatsinks where a flushing moves the air over the DCDistribution Fuse board, the Control and Metering Board, the Output Filter cir-cuits, and then out through the air vents on the side panels. If a fan fails, theamplifier will fold back power to prevent overheating.
4–5Principles of Operation
4.2 PS2000 Power SupplyThe PS2000 supplies power to the PA2000 by converting single-phase 240 VAC into 50 VDC. The PS2000 is protected by a 20 A double-pole circuit breaker.This highly efficient power supply utilizes switching technology and is power factorcorrected. The PS2000 consists of three printed circuit boards described below.
4.2.1 AC Input BoardThe AC Input Board is located on the left side of the PS2000. AC power from thecircuit breaker connects to the AC Input Board where it connects to a ±12 volt DCpower supply and three relays. The ±12 volts is used to close the three relays whenthe DC Power Switch on the front panel is switched on. In addition, the ±12 voltsare supplied to the PA2000 for use in the Control and Metering Board. The 240-volt AC input to the power supply is connected through a Hubble Twist Lockconnector on the back panel to a 20–amp circuit breaker mounted inside the backpanel.
When the power supply is turned on and enabled, the AC power comes throughtorroidal inductors which prevent harmonics and spurious products from feedingback into the AC power lines. The current flows from the inductors to a bridgerectifier that converts the current to DC Power, and from there to the PFC Switch-ing Board where the rectified DC is filtered. The filtered DC power is then fed fromthe PFC Switching Board through an 80–turn boost inductor and back to the PFCSwitching Board.
4.2.2 PFC (Power Factor Correcting) Switching BoardThe PFC Switching Board is located directly behind the cooling fans (front panel) inthe PS2000. This board takes the voltage from the Torroidal Boost Inductor andsends it to the Boost Switching Transistor. The switching transistor chops the DCinput power at a 25 kHz rate. The chopped voltage is then rectified, filtered, andsent as DC voltage to a set of four transistors which form a second switching stage.The second switching stage chops the DC voltage at a 22.5 kHz rate. This choppedDC power is fed through a blocking capacitor to a transformer on the DC OutputBoard. The second switching stage controls the amount of power sent to the DCOutput Board. This ensures that the transformer output voltage and current arecorrect for providing the selected RF output power to the amplifier.
in questo mondo,forse, uno si dicese diciamo che
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dice
se diciamo che
ma scrivendo con
se diciamo che
ma scrivendo con
4–6 FM2000A User’s Manual
4.2.3 DC Output BoardThe DC Output Board is located in the back of the unit directly behind the PFCSwitching Board. This board rectifies and filters the transformer output voltageonce again to produce the clean DC power required for the power modules. The DCOutput Board also provides the 24 volts that operate the cooling fans in both thePS2000 and the PA2000. There are two parallel paths from the DC Output Board,with half the power going through each set of output cables. These cables cometogether at the terminal in back of the unit providing the maximum output powerof 50 volts at 60 amperes.
4.2.4 Cooling FansThere are two cooling fans located in the front section of the PS2000. Their pri-mary function is to cool the semiconductors used in the switching and rectifyingprocess which are subject to high currents. The fans blow cool air through theheatsinks and out through the vents on the back and side panels of the PS2000.The fans have a dedicated circuit breaker located on the back panel of the powersupply.
5–1Troubleshooting
TROUBLETROUBLETROUBLE
Section 5—TroubleshootingThis section describes procedures for service personnel to diag-nose and troubleshoot potential fault conditions in the poweramplifier and power supply.
TROUBLETROUBLETROUBLE
5–2 FM2000A User’s Manual
5.1 Troubleshooting Flow Chart Analysis
Does your amplifier have output power?
Yes NoIs power
output at the proper level?
Yes No
See Section 3.1 Initial Power-up
procedures.
Do you have power now?
Yes No Is your exciter turned on?
Secure all connections to the
PS2000.
Ensure AC input circuit breaker is
flipped up
Ensure main power switch is
turned on.
Is exciter delivering sufficient RF drive?
(Check In Ref meter reading.)
Are there any fault
indicators?Yes No
Yes No
Antenna: See Section 5.3.1
RF Drive: See Section 5.3.2
PA Temp: See Section 5.3.3
PA DC: See Section 5.3.4
Yes No
See Section 3.1 Initial Power-up
procedures.
Call Support— See Section 8
Turn the exciter on.
5–3Troubleshooting
WWARNINGARNING
5.2 Digital Multimeter Parameters
The following procedures are general in nature; for in-depth service, and repair seethe Service & Support section of this manual.
If any abnormal readings are displayed for any of the following parameters on theDigital Multimeter, try troubleshooting in the following manner:
5.2.1 In Ref (Input Drive Reference)If this indication of drive level is not between 0.8 and 1.2 volts, then:
q Check the exciter to ensure proper power input level of 70–80 watts.
q Check RF input cable for secure connection.
5.2.2 SWR (Standing Wave Ratio)If the SWR is over 1.5:1, then look for:
q effects of inclement weather such as icing on the antenna and feed line.
q for moisture in the feedline.
q insecure antenna connections.
5.2.3 ALC (Automatic Level Control)If this indication is not between 4.00 and 6.00 volts for 2.2 kW output, then:
q Check for overheating (see PA Temp fault LED).
q Check for overcurrent (see PA DC fault LED).
q Check for high SWR (see Antenna fault LED).
5.2.4 Power OutThis reading is user adjustable, but for full output should read 2.20 for 2.2 kW.
q If lower than desired, check for proper input drive, and/or proper adjustmentof the Local Power Control (see section 3.1 #6).
Lethal voltages present!
Only technically qualifiedindividuals shoud attempttroubleshooting or serviceprocedures .
TROUBLETROUBLETROUBLE
5–4 FM2000A User’s Manual
5.2.5 PA TempThe meter should read between 35–50°C with an ambient temperature of 25°C. Iftemperature is 75°C or above, then check and do the following:
Ambient temperature higher than 50°C; reduce temperature.
Restricted air flow; remove any obstructions, clean dirty air filters by usingmild detergent and warm water.
Possible antenna mismatch; check for icing, moisture in the feedline, andsecure antenna connections.
Overcurrent: If PA DC fault indicator is flashing, monitor the current for aproper level—the total current and the current of individual Power Amps.
5.2.6 PA VoltageSupply voltage to the RF power amplifiers should be 50 V. If it is not check:
drive level to ensure proper power level input of 70–80 watts
for high SWR
for overcurrent; check PA DC fault indicator and if flashing, check current forproper levels (total and individual Power Amps)
for overtemperature; ambient temperature higher than 50°C; reduce tempera-ture. Check air flow; remove any obstructions and clean dirty air filters.
5.2.7 Tot CurrentIf total current reading is over 65 amperes, then check or do the following:
Reduce power output; check all fault indicators and troubleshoot accordingly.
If one or more of the 500–watt power modules has failed; replace.
High SWR; check for icing, moisture in the feedline, and secure antennaconnections.
5.2.8 PA1–8If there is 2.5 amps or more difference between the individual PA current readings(7 to 9 amps typical), then check the following:
Failed/faulty power module (reading directly correlates to failed power mod-ule); replace.
Blown individual power amplifier fuses 1–8; replace as indicated by red LED.
Reduced power output; check all fault indicators and troubleshoot accord-ingly.
5–5Troubleshooting
If one of the LED fault indicators is illuminated red, troubleshoot using the follow-ing suggestions:
5.3 Fault Indicators
5.3.1 AntennaAntenna mismatch.
Effects from inclement weather conditions such as icing.
Check for moisture in the feedline.
Secure antenna connections.
5.3.2 RF DriveDenotes lack of or insufficient drive level.
Ensure proper drive level of 70–80 watts input power.
Check RF input cable for secure connection.
5.3.3 PA TempTemperature has reached the internal preset limit for safe operation (75°C).
Ambient temperature higher than 50°C; reduce temperature.
Restricted air flow; remove any obstructions, clean dirty air filters by usingmild detergent and warm water.
Antenna mismatch; check for icing, moisture on the feedline, and secureantenna connections.
Overcurrent; check PA DC fault indicator, if flashing monitor current forproper levels (total and individual Power Amps).
Faulty DC Output Board; replace (see Section 7, Service & Support).
Faulty or non-functioning cooling fan; determine the cause for malfunctionin the following section.
5.3.3.1 Potential Causes for Non-functioning Cooling Fans
The PA2000 and the PS2000 have two cooling fans each. All fans are powered bythe same circuit of the PS2000. There are two potential causes for a non-function-ing fan or fans:
1. If a single fan does not operate, the fan is faulty and must be replaced. (SeeSection 7, Service & Support.)
2. If none of the fans operate, a blown circuit breaker, a short circuit in thePS2000, or a damaged winding on the main transformer of the DC OutputBoard (in the PS2000) is the cause. In this case, do one of the following:
TROUBLETROUBLETROUBLE
5–6 FM2000A User’s Manual
5.3.5 Multiple IndicatorsCall your Crown Broadcast service representative. See Section 7, Service andSupport, for contact information.
a. The circuit breaker is located on the rear panel of the power supply. If thebreaker has popped out, reset it by pushing it in. If the breaker continuesto trip, check for a short circuit.
b. Check each fan with a volt-ohm meter by disconnecting and testing it for ashort circuit. Replace the fan/fans as needed (see Section 7).
c. If none of the fans have short circuits, there is damage on the winding ofthe transformer. It will have to be replaced (see Section 7).
5.3.4 PA DCDiscrepancy in current between the individual amplifiers, or in total current.
There is a difference of current greater than 2.5 amps between any one of the4 individual amplifiers. This could occur as a result of a blown or faulty powermodule, or a blown fuse; replace as appropriate (see Section 7, Service &Support).
There is too much total current—power foldback will occur above maximumtotal amperage of 65 amps due to some malfunction. For antenna mismatchcheck for arcing and moisture. Also, check output power for proper current;the RF detection circuit could malfunction causing an overcurrent situation.
6–1Reference Drawings
Section 6—Reference Drawings
The illustrations in this section may be useful for makingadjustments, taking measurements, troubleshooting, orunderstanding the circuitry of your RF power amplifier andpower supply.
6–2 FM2000A User’s Manual
Illustration 6–2 Back View
Illustration 6–1 Front View
6.1 Views
Fault
AntennaRF DrivePA TempPA DC
PA1PA2PA3PA4
PA5PA6PA7PA8
Power OutPA TempPA VoltageTot CurrentALC
SWRIn Ref
Metering
PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8
Fuses
®
®
Power
I
O
RF Input
Remote I/O
Control
RF Monitor(Optional Connection)
RF Output
Circuit Breakers
+ DC Input
DC Input
+ DC Output
DC Output
Air Intakes/Filters
FansPower
Control
OFF OFF
240 VAC IN
PA2000
PS2000
Ground Screws
Air Exhaust Vents
6–3Reference Drawings
Illustration 6–3 FM2000A Block Diagram
6.2 Diagrams and Schematics
50-70 watt exciter(Crown FM100)
PA2000Power Amplifier
RF output
Control
PS2000Power Supply
RF Input
240 volts AC 50/60 Hz Input Power
Single Phase
DC output
DC input
Control
2 kW RFPower Output
I/OTo remote control andmonitoring equipment
6–4FM
2000A User’s Manual
Illustration 6–4 PS2000 Block Diagram
240 VACAC
CIRCUITBREAKER
AC INPUT
NEUTRAL
GROUND
ACINPUTCCA
POWERSWITCH
RECTIFIERPFC &
CONTROLCCA
DCOUTPUT
CCA
+ 0 to 50 VDC
RETURN
PS CONTROL9-PINDSUB
220 VDC
+/ 12 VDC
VOLTAGEBOOST
INDUCTOR
360 VDC
360 VDC
CONTROL
GND EARTH
GND CHASSIS
GND SIGNAL
GND FIELD SIGNAL
L1
T1
1
2 4
5
650-ohmREAR PANEL
From PFC Switcher Board
To DC OUTPUT BOARD
L100(FRONT PANEL)
NOTES :______________
1. ALL RESISTORS ARE IN OHMS,1/4W, 5% UNLESS OTHERWISESPECIFIED.
2. ALL CAPACITORS ARE INMICROFARADS UNLESSOTHERWISE SPECIFIED.
220-240VAC IN
REV
Q43521-6DWG. NO.
PROJ NO.SCALE: NONE
TITLE:
SIZE
BUNCONTROLLED
UNLESS OTHERWISE MARKED IN RED INK BY CM ASA CONTROLLED COPY, COPIES OF THESE DOCUMENTS INCLUDING ASSOCIATED ELECTRONICREPRODUCTIONS ARE FOR REFERENCE ONLY.
SCH, FM2K POWER SUPPLY AC INPUT
SHEET 10 OF 10
J103
THESE DRAWINGS AND SPECIFICATIONS ARE THEPROPERTY OF INTERNATIONAL RADIO ANDELECTRONICS CORP., AND SHALL NOT BEREPRODUCED, COPIED, OR USED AS THE BASISFOR THE MANUFACTURE OR SALE OF APPARATUSOR DEVICES WITHOUT PERMISSION.
-12V
-12V+12V +12V
POWER OFF/ON
+12V
-12V
C31.5UF/630V
HD3HEADER 5X2
1 23 45 67 89 10
CB1A15A
CB1B15A
J1
C1.0033250VAC
C2.0033
250VAC
K1RELAY 24V
K2RELAY 24V
D11N4004
D21N4004
SW1DC Power
SW2AC Power
R1PTC
D31N4004
D41N4004
C1122050V
VR1LM2586-ADJ
1 2 3 4 5
R91.10K
D52N5822
R1010.0K
C151.0
C161.0
C1422050V
C1322050V
L4330UH
L5330UH
C1247
20V
D62N5822
Q1IRFD9113
C10.001
R71K
R51K
U14N37N
Q2IRFD9113
R810K
HD2
12
R25 PTC
R35 PTC
K3RELAY 24V
R100.04 OHM
D1BDF01
-+
C91.5
630v
C7.0033
250VAC
C8.0033
250VAC
L2100UH
L3100UH
R45.63W
C6.47
250VAC
C5.0033
250VAC
C4.0033
250VAC
MOV1V217HA40
MOV2V271HA40
MOV3
V27
1HA
40
MOV4
V27
1HA
40
GND CHASSIS
GND SIGNAL
GND FIELD SIGNAL
15VDC
+-
(25KHZ)
(22.5KHZ)
25V
R58 for AC current foldback.
Install R58.
*
*
*
NOTES :______________
1. ALL RESISTORS ARE IN OHMS,1/4W, 1% UNLESS OTHERWISESPECIFIED.
2. ALL CAPACITORS ARE INMICROFARADS UNLESSOTHERWISE SPECIFIED.
T2 80t
5t
1
2
3
4
5
6
T2XFMRGATE
T3
1
2
3
4
5
6
T1XFMRGATE
4 1N5818
THESE DRAWINGS AND SPECIFICATIONS ARE THEPROPERTY OF INTERNATIONAL RADIO ANDELECTRONICS CORP., AND SHALL NO BEREPRODUCED, COPIED, OR USED AS THE BASISFOR THE MANUFACTURE OF DEVICES WITHOUTPERMISSION.
REVDWG. NO.
SHEET 10 0F 10
LUNCONTROLLED
UNLESS OTHERWISE MARKED IN RED INK BY CM ASA CONTROLLED COPY, COPIES OF THESEDOCUMENTS INCLUDING ASSOCIATED ELECTRONICREPRODUCTIONS ARE FOR REFERENCE ONLY. SCALE: NONE PROJ NO.
TITLE:
SIZE
C
103
SCH, FM2K PWR SUP PFC SWITCHER
Q43522-4
NOT ON PWB
D1HFA25TB60J3
IND1J4
IND2
J6XFMR2
J2
BRIDGE+
J1BRIDGE-
J5XFMR1
C46.001
C18.001
DS11N5818
Q1
2N5210
R10.04
3%15W
C13.01
C12.0039
C11.01
C101.0
C2010
C510
C61.0
C4.01
C15.00473KV
C44.0033
250VAC
HD1
1 2
DS31N5818
DS41N5818
C9.47
C8.047
U1LT1248
88
77
66
55
44
33
22
11
9 9
10 10
11 11
12 12
13 13
14 14
15 15
16 16
D101N4148
C491035V
C144.7
C1747
D41N4004
R334.7K
5%
C501.5
630VDC
C26470
C25470
C24470
C23470
VR17815CT
IN2
C1
OUT 3
C191000
D21N4004
R2315K
5%3W
R2415K
5%3W
DZ224V
R344.7K
5%
HD2
1 2
QF1IGBT, 600V 50A FAST
DL1LED
DS21N5822
QF4IGBT, 600V 50A FAST
QF5IGBT, 600V 50A FAST
C38.0016KV
C39.0016KV
C36.01
C35.0015
R624.7K
5%
DL2LED
DS141N5818
DS131N5818
DS121N5818
DS111N5818
U2UC3875
1010
99
88
77
66
55
44
33
22
11
11 11
12 12
13 13
14 14
15 15
16 16
17 17
18 18
19 19
20 20
C42.01
R164.3K
5% D31N4004
C404.7
400VDC
D61N4148
D81N4148
C371.0
D71N4148
D91N4148
R5120
1%
QF2IGBT, 600V 50A FAST
QF3IGBT, 600V 50A FAST
U34N37
B 6
C 5
E 4NC3K2A1
U44N37
B6
C5
E4 NC 3K 2A 1
HD3
123456
C2147
C43.01
C34330PF
C331.0
C41.01
C32.001
C45.001
DS7DS9
DS10DS8
C29.001
C3147
C30.01
C270.1
C280.1
R920K
R17OPEN
R222K
R2810K
R2910K
R2115K
R363.01K
R3775K
R356.81K
R453.01K
R141K
R2720.5KR20
20KR5522.1K
R5810K
R44.02K
R34.02K
R7100
R101K
R56100K
R57100K
R1275K 75K
R1910
R3110
R305.11K R39
75KR40
5.11K
R3810
R4810
R4710K
R4910K
R4410
R4310K
R4110K
R4210
R1810
R4610
R501K
R5233
5%2W
R5333
5%2W
R3222
5%3W
R15
330K5%
R114.3K
5%
R83005%
Q3
2N5087
HD4
12
HD5
12
HD6
12
DL3AMBER
C22.001
C47.001
C48.001Q2
2N5087
R593.32K
R544.99K
C1.001
C7.001
C2.001
C3.001
D5
OPE
NC16.0016KV
R21.50K
R5511K.5W
R6511K.5W
R25511K.5W
R26511K.5W
C51.001
D120 OHM
D110 OHM
R602.74K
L1JUMPER
DW
G.
NO
.R
EV
.20
0983
-SC
HC
1 2 3 4 7 8
A
B
C
D
E
F
1 2 3 4 6 7 8
A
B
C
E
F
5
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OFINTERNATIONAL RADIO AND ELECTRONICS CORP.AND ARE NOT TO BE REPRODUCED, COPIED OR USED AS THE BASISFOR THE MANUFACTURE OR SALE OF APPARATUS ORDEVICES WITHOUT PERMISSION. 1 1SHEET OFSCALE : NONE PROJ NO.FILENAME:
DWG . NO . REV.
C200983-SCH
TITLE:
UNCONTROLLEDUNLESS OTHERWISE MARKED IN RED INK BY CM AS ACONTROLLED COPY, COPIES OF THESE DOCUMENTSINCLUDING ASSOCIATED ELECTRONIC REPRODUCTIONSARE FOR REFERENCE ONLY.
APPROVALSDWNCHKCMPE
DISTRIBUTION
E . C . N. REV DESCRIPTIONAPPROVALS
PECHK CMDATE DWNREVISION HISTORY
65
SIZEB
B_L_SHT1_A.DOT REV. A
INTERNATIONAL RADIO AND ELECTRONICS CORP.25166 LEER DRIVE ELKHART, IN. 46514574-262-8900 WWW.IREC1.COM
IREC
DZ116V
L5150uH
+ C21220/35V
Vin1
ON/OFF5
FEEDBACK 4
OUT 2
GND3
U2
LM2596T-ADJ
D16
MUR420
2
31
84
U1A
LM358
1%
1%
R2018.7K
R211.0K
T1
C19
.0047
R1910
3W
D5
MBR3100
D6
MBR3100
D7
MBR3100
D8
MBR3100
C131
+ C14220/35V
+27V
C20470pF
D9
MUR130D10
MUR130
D1
BYV44-300
D2
BYV44-300
D11
MUR130D12
MUR130
D3
BYV44-300
D4
BYV44-300
D13MUR130
D14MUR130
L1
89 uH
L3
89 uH
+
C7.47/160V
R11K5W
D15
1N4004
1 23 45 67 89 10
HD1
HEADER 5X2
+C8.47/160V
R51K5W
R615K1/2W
C90.1
+12V
R1010K
R9
51K1%
1 2 3
HD3HEADER 3
R13100K
R7234K
C11220pF
1%
L2
89 uH
L4
89 uH
+C13300
+C43300
+C23300
+C53300
C31
C61
1234
J3
4 HEADER
1234
J4
4 HEADER
123456
HD2
HEADER 6
R25.11K1% R3
1M1%
R4
510K
C10
.1
R18
5.11K1%
C12.01 R8
10K1%
ALC
FAN +24VDC
FAN +24VDCFAN GND
R12
3.01K
R112.0K
1%
1%
CONTROL0-6VDC IN
(5V FOR 50V OUT)ALC
INT/EXT
LOCALCONTROL
R1410
3W
R1510
3W
C15.0047
C16.0047
R1610
3W
R1710
3W
C17.0047
C18.0047
TO RF PA'S50V 24A
TO RF PA'S50V 24A
1
J5
1
J6
1
J1
1
J2
TOFAN FUSE
NOTES:UNLESS OTHERWISE SPECIFIED:
1. ALL RESISTORS ARE IN OHMS, 1/4W, 5% TOL.
2. ALL CAPACITORS ARE IN MICROFARADS.
5
67 U1B
LM358SCH, POWER SUPPLY DC OUTPUT
533
DW 01/17/05
200983-SCH
DW 01/17/05
C REDRAWN ON IREC FORMAT, AND ADDED U2,D16,L5,C20-21,R20-21 01/17/05 DW DW
12
11
13,14
15,16,17,18
19,20
9,10
5,6,7,8
3,4
2
1
FAN +24VDC
6–8FM
2000A User’s Manual
Illustration 6–5 PA2000 Block Diagram
6–9Reference Drawings
PA2000 RF Input
RFOUTPUT
C247PF NP0 R4
10
FWD
REFL
C147PF NP0
C3.001
C6.01
C5.01
D11N6263
R720K
R520K
C4.001
D21N5263
R620K
R182
R820K
1 2 3 4 5
HD1
R282
R310
BNC 1
3. C1201-1209A,1217 are circuit board pads.
NOTES :______________
1. ALL RESISTORS ARE IN OHMS,1/4W, 5% UNLESS OTHERWISESPECIFIED.
2. ALL CAPACITORS ARE INMICROFARADS UNLESSOTHERWISE SPECIFIED.
RF InputReflectometer & Splitter
J0744-3m
RF INPUT(Back Panel)
Coa
xual
Cab
le C
onne
ctio
n
Coa
xual
Cab
le C
onne
ctio
n
RF IN
6–10 FM2000A User’s Manual
500 W Power Amp
RFI
NR
FOU
T
VPW
R
RFI
NR
FOU
T
VPW
R
DZ11
101N
4735
6.2V
R111
920
0 3W
R112
02.7
K
C112
10.0
1DI
SC
R111
25.6 2W
R111
35.6 2W
R110
115
K
R111
010
K
R111
724 3W
C113
80.0
68
C111
20.0
1C1
113
0.01
C111
40.0
1C1
115
0.01
R111
610
C111
627
PF
C111
0
0.01
C111
10.0
1
C112
20.0
1DI
SC
L112
250
NH
L112
150
NH
C112
560
PF
C112
30.0
1C1
124
0.01
PA O
UTPU
T BD
T112
1
T11S
R111
45.6 2W
R111
55.6 2W
PA IN
PUT
BD
Q110
1BL
F278
T111
1P
R111
110
KPO
T V
DZ11
101N
4735
6.2V
R111
920
0 3W
R112
02.7
K
C112
10.0
1DI
SC
R111
25.6 2W
R111
35.6 2W
R110
115
K
R111
010
K
R111
724 3W
C113
80.0
68
C111
20.0
1C1
113
0.01
C111
40.0
1C1
115
0.01
R111
610
C111
627
PF
C111
0
0.01
C111
10.0
1
C112
20.0
1DI
SC
L112
250
NH
L112
150
NH
C112
560
PF
C112
30.0
1C1
124
0.01
PA O
UTPU
T BD
T112
1
T11S
R111
45.6 2W
R111
55.6 2W
PA IN
PUT
BD
Q110
1BL
F278
T111
1P
R111
110
KPO
T V
L24
PA O
UT
PA O
UT
PA O
UT
L14
PA IN
PA IN
PA IN
C1 1.0
C2 1.0
L18
GN
D
GN
D
GN
D
PA IN
GN
D
AMPB
DC
PW
R
AMPB
DC
PW
R
AMPB
DC
PW
R
AMPA
DC
PW
R
AMPA
DC
PW
R
L28
GN
D
GN
D
GN
D
PA O
UT
GN
D
C5 1.0
C6
1.0
U1
LM35
DZ
TEM
PER
ATU
RE
SEN
SE
C3
1.0
C4 1.0
GN
D
GN
D
AMPA
DC
PW
R
GN
D
GN
D
TEM
P V+
TEM
P AM
P A&
B
NO
TES
:__
____
___
____
_
1. A
LL R
ESIS
TOR
S AR
E IN
OH
MS,
1/4W
, 5%
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
2. A
LL C
APAC
ITO
RS
ARE
INM
ICR
OFA
RAD
S U
NLE
SSO
THER
WIS
E SP
ECIF
IED
.
THES
E D
RAW
ING
S AN
D S
PEC
IFIC
ATIO
NS
ARE
THE
SHAL
L N
OT
BE R
EPR
OD
UC
ED, C
OPI
ED, O
R U
SED
AS T
HE
BASI
S FO
R T
HE
MAN
UFA
CTU
RE
OR
SAL
EO
F AP
PAR
ATU
S O
R D
EVIC
ES W
ITH
OU
T PE
RM
ISSI
ON
.
PRO
PER
TY O
F C
RO
WN
INTE
RN
ATIO
NAL
, IN
C. A
ND
GN
D
GN
D
GN
D
250W
RF
PWR
AM
P A
250W
RF
PWR
AM
P B
CR
OW
N IN
TER
NAT
ION
AL,
INC
.17
18 W
EST
MIS
HAW
AKA
RO
AD
FM20
00, 5
00W
RF
PW
R A
MP
CC
A
ELKH
ART,
IN. 4
6517
PHO
NE
(219
) 294
-800
0
REV
J074
6-8
b
6–11Reference Drawings
RF Output Combiner
6–12 FM2000A User’s Manual
RF OUTPUT FILTER & REFLECTOMETER
PA R
FO
UT
PU
T
C12
1147
PF
NP
0R
1212
10 0.50
W
C12
067.
1PF
C12
079.
3PF
C12
085.
13P
F
L120
394
.1N
HL1
204
87.5
NH
(195
MH
z)(1
76M
Hz)
(252
MH
z)
C12
09A
1PF
L120
577
.9N
H
RF
IN
C12
001.
35P
F
L120
290
.5N
H
(455
MH
z)
C12
0115
.4P
FC
1202
40.9
PF
L120
125
0NH
C12
01A
10P
F
C12
0338
.9P
FC
1204
37.7
PF
C12
0514
.1P
FC
1210
82P
F S
M
F W D
R E F L
C12
1247
PF
NP
0
C12
13.0
01
C12
15.0
1C
1214
.01
D12
011N
6263
R12
1610
0K
R12
151K
C12
16.0
01
D12
111N
5263
R12
181K
R12
1420
00.
5 W
R12
1710
0K
12
34
5
HD
1202
HE
AD
ER
5
R12
1610
0
14
3 3 3 3
LEN
GT
H
0.7"
0.6"
GU
AG
E
#17
#12
#12
#12
#12
0.6"
0.5"
0.7"
L120
1
L120
2
L120
3
L120
4
L120
5
I.D.
TU
RN
S
0.25
"
0.5"
0.5"
0.5"
0.43
75"
IND
UC
TOR
S
EX
AC
T C
OIL
LE
NG
TH
S A
RE
FA
CTO
RY-
SE
T.3.
C12
01-1
209A
,121
7 ar
e ci
rcui
t boa
rd p
ads.
NO
TE
S :
____
___
____
___
1. A
LL R
ES
ISTO
RS
AR
E IN
OH
MS
,1/
4W, 5
% U
NLE
SS
OT
HE
RW
ISE
SP
EC
IFIE
D.
2. A
LL C
APA
CIT
OR
S A
RE
INM
ICR
OFA
RA
DS
UN
LES
SO
TH
ER
WIS
E S
PE
CIF
IED
.J0
750-
0
RF
Out
put
Filt
er &
Ref
lect
omet
er
R12
1120
00.
50 W
R12
1310 0.
50 W
RF
MO
NIT
OR
1-10
PF
6–13 FM2000A User's Manual
in questo mondo,forse, uno si dicese diciamo che
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dicese diciamo che
ma scrivendo con
ma scrivendo conin questo mondo,forse, uno si dice
se diciamo che
ma scrivendo con
se diciamo che
ma scrivendo con
Backplane Distribution
Note: All bypass capacitors are 0.01 mf
6–14Reference Drawings
Ribbon Cables and Connectors
Ribbon Cables and Connectors
10mv per degree C.
(0.2VDC at 2000W)
SWR CAL
DENOM
NUMER
POWER CAL
SWR clamp @ <200W
(1.5:1)49.9K FOR 2:1
100uA/A
.5V/A
.5V/A
100uA/A
100uA/A
100uA/A
100uA/A
100uA/A
100uA/A
100uA/A
PA LIMIT
INPUT FWD
INPUT REV
OUTPUT FWD
OUTPUT REV
(0.1V at 1.00)
(.35VDC at 35 degrees)(.48V at 48 volts)(.5VDC at 50 amps)
.05V/A
.5V/A
.5V/A
.5V/A
.5V/A
.5V/A
.5V/A
1N4148
*
POWER RANGE
U1,3,5,6,8,24,25 U2,4,26,29 U27 U28
4
11
8
4
1,8
4,5
7
4(40mv/A)
(DETERMINED BY DIR. CPLR. SENSITIVITY.)
DIFFERENTIAL PA ERROR CURRENT SENSE.
R158 = OPEN: HIGHEST-LOWEST = 2.4 AMP.
R158 = 240K: HIGHEST-LOWEST = 1.2 AMP.
(LOWEST PAI)
(HIGHEST PAI)
1
2
3
4 72
7169
70
Metering Card Edge Connector
Viewed from front panel
NO PINNO PIN
NO PINNO PIN
NO PINNO PIN
NO PINNO PIN
(SPARE)
(SPARE)
(SPARE)
UNITSTENS100's
SWR
ALC19.99
19.99
199.9
199.9
F.S.
DECIMAL POINT
199.9
POWER SET
J2-12
(0.2VDC at 2000W)
PA1
PA2
PA3
PA4
PA6
PA7
19.99
19.99
19.99
19.99
19.99
19.99
19.99
19.99
19.99
SWRALC
PA DC VOLTSPA DC AMPS
19.9919.99
199.9199.9
199.9PA TEMPERATURE
19.99
PA1PA2PA3PA4PA5PA6PA7PA8
19.9919.9919.9919.9919.9919.9919.9919.99
(0.1V at 1.00)(0.6v at 6v)
(.35VDC at 35 degrees)(.48V at 48 volts)(.5VDC at 50 amps)
(1.999V reads "1999" FULL SCALE)
POWER OUT
PA TEMP
PA VOLTS
PA AMPS
19.99 PA8
19.99
KW OUT
DRIVE
19.99 DRIVE
U16-23U7,14U13
7
4
1
26
14
7
16
U15
8
16
7,8
MSB
LSB
U11,12U9,10
16
7 8
LOCAL ONLY
.5V PER AMP
.5V PER AMP
.5V PER AMP
.5V PER AMP
.5V PER AMP
.5V PER AMP
.5V PER AMP
.5V PER AMP
RF output power is limited by the lower of:
Front panel OUTPUT control.
Remote RAISE/LOWER step circuit, orRemote PWR CTRL analog input, or
NOTES :______________
1. ALL RESISTORS ARE IN OHMS,
2. ALL CAPACITORS ARE IN
PA5
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY
SHALL NOT BE REPRODUCED, COPIED, OR USEDAS THE BASIS FOR THE MANUFACTURE OR SALEOF APPARATUS OR DEVICES WITHOUT PERMISSION.
OF INTERNATIONAL RADIO & ELECTRONICS CORP. AND
SCALE NONE
DWG. NO.
Q43514-1005,006
SCH, FM2K CONTROL & METERING
PROJ NO. SHEET 16 OF 16
JREV
TITLE:
SIZE
DUNCONTROLLED
UNLESS OTHERWISE MARKED IN RED INK BY CM ASA CONTROLLED COPY, COPIES OF THESEDOCUMENTS INCLUDING ASSOCIATED ELECTRONICREPRODUCTIONS ARE FOR REFERENCE ONLY.
1/4W, 5% TOL.
MICROFARADS.
UNLESS OTHERWISESPECIFIED:
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
DS101ADS101BDS101CDS101D
5%
5%
5%
5%
5%
5% 5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
+
+
+
+
+
+
XDS101
NOTES:UNLESS OTHERWISE SPECIFIED:ALL RESISTORS ARE IN OHMS, 1/4W, 1% TOL.ALL CAPACITORS ARE IN MICROFARADS.
6.2V
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
GRN
6.2V
6.2V
6.2V
5%
5%
FOLDBACKCAL.
RF FWD MEM BATT
REM RF POWER
REM /PWR RAISE
RF REV
REM /PWR LOWER DP10DP100
REM SWR
DRIVE REV
DRIVE FWD
DPM INREM RF DRIVE
REM ALC
DPM REF
ALC
PATEMP 1-2FAULT SUM
+50V
PATEMP 3-4
REM PAVPAV SENSE SWR LAMP
REM PA TEMP
PATEMP 5-6
DRIVE LAMP
PATEMP 7-8+12V IN +12V
SH HI 1PATEMP LAMP
SH LO 1
PS /POWER ON RF FWDRF REV PADC LAMP
ALC DRIVE FWD -12V IN -12V-12V IN DRIVE REV SH HI 2GND REM RF POWER+12V IN REM SWRREM PA TEMP REM PAVREM ALC REM PAITFAULT SUM REM PAI1 SH LO 2REM /PWR ON REM PAI2REM PWR CTRL REM PAI3 DP10REM /PWR RAISE REM PAI4REM /PWR LOWER REM PAI5 DP100
REM PAI6REM RF DRIVE REM PAI7 SH HI 3GND REM PAI8
GND GNDGND GND SH LO 3
REM PAITGND SH LO 1
SH HI 1PATEMP 7-8 SH LO 2PATEMP 5-6 SH HI 2 SH HI 4PATEMP 1-2 SH LO 3TEMP V+ SH HI 3PATEMP 3-4 SH LO 4SH HI 4 SH LO 5SH HI 5 SH LO 6 SH LO 4SH HI 6 SH LO 7SH HI 7 SH LO 8SH HI 8 +50VPAV SENSE IN'LK 1MEM BATT IN'LK 2
SH HI 5
SH LO 5REM PAI1REM PAI2REM PAI3REM PAI4REM PAI5
SH HI 6 REM PAI6REM PAI7REM PAI8
SH LO 6
IN'LK 2PS /POWER ON
IN'LK 1REM /PWR ON SH HI 7
+12V IN TEMP V+ SH LO 7
GND
SH HI 8
SH LO 8
REM PWR CTRL
+5V
+12V
+12V
+12V
+12V
PA+5V
+12V
+12v
+5.00
+12V
+5.00
+12V
+12V+12V
+12V
PA+5V
PA+5V
PA+5V
+5V
+5V
+5V
+12V
PAV+6
+5.00
+5.00
+12V
+12V
+12V
-12V
-12V
-12V
-12V
-12V
-12V
PA-5V
-12V
-5V
-12V
-12V
-12V-12V
-12V
-12V
-12V
PA-5V
PA-5V
PA-5V
PAV-6
+5.00
-12V
-5V
-12V
+12V
+12V
+5V
-5V
-12V
+5V
PA-5V
PA+5V
-5V
+5.00
+5.00
+5V
-5V
VCC
VDD
VSS
VEE
-12V
+5V
+5V
+5V
+5V
+5V
+5V +5V
D261N4148
C33100PF
DZ11N753A
DZ21N753A
D241N5822
D25
1N5822
U28
REF02
IN2
TEMP3
TRIM5OUT 6
C8347/20V
C98.01
C101.001
U14C74HC132
9
108
U7B74HC14
3 4
U7C74HC14
5 6
U7A74HC14
1 2
U14D74HC132
12
1311
DS20
DS19
DS18
DS17
DS16
DS15
DS14
DS13
DS12
DS11
DS10
DS9
DS8
DS7
DS6
R201100
R202100
R203100
R204100
R205100
R206100
R207100
R208100
R209100
R210100
R216100
R215100
R214100
R213100
R212100
R211100
C62.001
R144100
R143100
R140100
R139100
R137100
C55.001
R136100
R134100
R133100
R131100
R130100
C47.001
R128100
R127100
R125100
R124100
R122100
R121100
U16AMC33282
2
31
84
U16BMC33282
6
57
U17AMC33282
2
31
84
U17BMC33282
6
57
U18AMC33282
2
31
84
U18BMC33282
6
57
U19AMC33282
2
31
84
U19BMC33282
6
57
C63.01
Q132N5087
Q122N5087
Q112N5087
Q102N5087
Q92N5087
Q82N5087
Q72N5087
Q62N5087
R1454.99K
R1414.99K
R1384.99K
R1354.99K
R1324.99K
R1294.99K
R12
64.
99K
R1234.99K
U25DTL074
+
-13
1214
U25CTL074
+
-9
108
U25BTL074
+
-6
57
U25ATL074
+
-2
31
411
U24DTL074
+
-13
1214
U24CTL074
+
-9
108
U24BTL074
+
-6
57
D44
D46
D47
D48
D49
D50
D51
D27
D28
D30
D31
D29
D32
D33
D34
R1564.3K
R15710K
R158OPEN
U8DTL074
+
-13
1214
U26AMC33282
2
31
84
U26BMC33282
6
57
R1461.0K
R14810K
C22100PF
R14720K
C75.001
C74.001
C76.001
C77.001
C78.001
C79.001
C80.001
C81.001
R168 100R167 100R166 100R165 100R164 100R163 100R162 100
R169 100
R154220K
C19.001
U5DTL074
+
-13
1214
U5CTL074
+
-9
108
C20.001
R4910K
R50470
R4710K
U5BTL074
+
-6
57
D91N4148
D81N4148
D71N4148
R4510K
D61N4148
R4310K
C14.001
U5ATL074
+
-2
31
411 C16
.001
R421K
R112220K
C13.001
R113220K
R441K
C15.001 C18
.001
R461K
R481K
U3DTL074
+
-13
1214
C70.001
R53100
R52100K
R108220K
C1.001
C2.001
R562K
R3100K
U1ATL074
+
-2
31
411
R410K
R11K
R121K
R109220K
C4.001
U1BTL074
+
-6
57
C5.001
R15510
R14100K
U1CTL074
+
-9
108
C10.001
R37100KC9
.001R110220K
R361K
R391K
R111220K
C11.001
U1DTL074
+
-13
1214
C12.001
R41100K
R4022.1K
R849.9K
U2BMC33282
6
57
D101N4148
R749.9K
R63.32K
D111N4148
C3.01
U2AMC33282
2
31
84
R1610K
U3ATL074
+
-2
31
411
R1910K
R17
10K
R2310K
R211K
U4AMC33282
2
31
84
C6.01 R20
3.32K
R2849.9K
R2510K
R2210K
R2410K
Q14
2N5210R26
100K
D51N4148
Q3LM394
11
22
33
44
8 8
7 7
6 6
5 5
Q4LM394
11
22
33
44
8 8
7 7
6 6
5 5
R3112.1K
U4BMC33282
6
57
C7.01
R273.32K
U3CTL074
+
- 9
108
U3BTL074
+
-6
57
C8.001
R3310K
R35100
R2910K
R305.11K
R101.15K
R910.0K
R11100
C340.1
R17410K
SW3RAISE
R17610K
R17351.1K U29A
74HC1321
23
U29D74HC132
12
1311
U29C74HC132
9
108
U29B74HC132
4
56
R17551.1K
C951.0
SW4LOWER
R1783.32K
D371N4148
D381N4148
R1771M
R610
U3174HCT193
A15
B1
C10
D9
UP5
DN4
LOAD11
CLR14
QA 3
QB 2
QC 6
QD 7
CO 12
BO 13 R1804.99KD53
1N4148
D521N4148
R1791M
R591K
D391N4004
R1834.99K
U33DTL074
+
-13
1214
U33BTL074
+
-6
57
D411N4148
C100.001
U33CTL074
+
-9
108
U33ATL074
+
-2
31
411
R1863.32K
D431N4148
C350.1
U9
74HC4051
X013
X114
X215
X312
X41
X55
X62
X74
INH6
A11
B10
C9
X 3
D131N4148
R6751.1K
R70100K
R6910K
C230.1
U8BTL074
+
-6
57
R68200K
C24.001
R72100
R71100
R7310K
U8ATL074
+
-2
31
411
U6BTL074
+
-6
57
R75100K R77
1MC260.1
C250.1
R6520K
R781K
R661M
R79 1K
R8010K
R81OPEN
U6CTL074
+
-9
108
R827.5K
R83121K
U6ATL074
+
-2
31
411
C27.001
R851M
R150OPEN
R149100K
R865.11K
U6DTL074
+
-13
1214
R18200K
D351N4148
D361N753A
C28.01
R88OPEN
C69.001
R741.15K
R9710K
C72.001U7E
74HC14
11 10
DS1RED
D141N4148
D151N4148
D161N4148
R89121K
R91121K
R93121K
R94100K
R92100K
R90100K
DS2RED
D191N4148
D201N4148
D181N4148
U7D74HC14
9 8
R96100K
R9556K
D171N4148
R98220K
DS4RED
DS3RED
U7F74HC14
13 12
R99510
R16156K
C370.1
R116220K
R1141K
SW2DOWN
U14A74HC132
1
23
C380.1
R117220K
U14B74HC132
4
56
R115511K
R1183.32K
SW1UP
D231N4148
R1031M
D221N4148
C320.1
C300.1
R101475K
C310.1
C360.1
R1052.49K
R10410K
R170510
R171510
RFC333UH
RFC433UH
DZ4ICTE-12
DZ5ICTE-12
VR1MC7805CT
IN2
C1
OUT 3
C911.0
C921.0
VR2LM79L05ACZ
IN2
C1
OUT 3
C871.0
U1174HC4051
X0 13
X1 14
X2 15
X3 12
X4 1
X5 5
X6 2
X7 4
INH 6
A 11
B 10
C 9
X3
U1274HC4051
X0 13
X1 14
X2 15
X3 12
X4 1
X5 5
X6 2
X7 4
INH 6
A 11
B 10
C 9
X3
RFC133UH
R15210K
U27
TSC4429
26
7
1 8
4 5
R5610K
U8CTL074
+
-9
108
R58100
R10610K
R1071.15K
C71.001
R5449.9K
D121N4148
Q1LM394
11
22
33
44
8 8
7 7
6 6
5 5
Q2LM394
11
22
33
44
8 8
7 7
6 6
5 5D1
1N6263
D21N6263
D31N6263
D41N6263
R151100
U10
74HC4051
X013
X114
X215
X312
X41
X55
X62
X74
INH6
A11
B10
C9
X 3
R1604.3K
C99.001
D421N4148
C104.001
SW5Switch
123
PL1
HDR 72
1 23 45 67 89 10
11 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 6465 6667 6869 7071 72
R142100
R200100
R159100K
R63510
R621K
C103.001
DZ31N753A
R102100K
R100100K
C6747/20V
C6847/20V
C17.001
C60.01
C57.01
C54.01
C51.01
C48.01
C45.01
C42.01
R60100
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
R1821K
R1811K
R219OPEN
R220OPEN
R221OPEN
C106.001
R218OPEN
D211N4148
C93 20pF
R120150
C61.001
R6410K
C59.001
R2171K
C50.001
C973300/16V
C102.001
C52.001
C6612063V
R8420K
C824720V
C41.001
C40.001
C43.001
R7624.9K
C391.0
R1322.1K
R5124.9K
C901.0
C891.0
R8750K
C105.001
R153220K
C56.001
U32DAC0800
B812
B711
B610
B59
B48
B37
B26
B15
VR+14
VR-15
IOUT 4
IOUT 2
COMP 16
VLC 1
U15
74HC193
A15
B1
C10
D9
UP5
DN4
LOAD11
CLR14
QA 3
QB 2
QC 6
QD 7
CO 12
BO 13
U3074HCT193
A15
B1
C10
D9
UP5
DN4
LOAD11
CLR14
QA 3
QB 2
QC 6
QD 7
CO 12
BO 13
R155OPEN
D401N4004
C53.001
C851.0
R222.1K
C46.001
C44.001
R17224.9K
C881.0
C64.01
R32510
C58.001
C941.0
R3822.1K
C21.001
C961.0
C291.0
R341.15K
C861.0
R571.15K
U13DISP-40
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
C841.0
R119150
C49.001
C731.0
R222OPEN
U24ATL074
+
-2
31
411
D45
R223OPEN
R2240
RFC2
10
C651/63V
R2260
R225OPEN
R227OPEN
6–16Reference Drawings
Notes:
7–1Service and Support
Section 7—Service and SupportWe understand that you may need various levels of support orthat the product could require servicing at some point in time.This section provides information for both of these scenarios.
7.1 Service The product warranty (see opposite page) outlines our responsibility for defective products. Before returning a product for repair or replacement (our choice), call our Customer Service department using the following telephone number:
(866) 262-8917 Our Customer Service Representative will give you further instructions regarding the return of your product. Use the original shipping carton or a new one obtained from Crown. Place shipping spacers between the slide-out power amplifier assembly and the back panel. Please fill out the Factory Service Instructions sheet (page 7–5) and include it with your re-turned product. 7.2 24–Hour Support In most instances, what you need to know about your product can be found in this manual. There are times when you may need more in-depth information or even emergency-type information. We provide 24–hour technical assistance on your product via a toll telephone call. For emergency help or detailed technical assistance, call
(866) 262-8917
You may be required to leave a message at this number but your call will be returned promptly from our on-call technician.
7.3 Spare Parts To obtain spare parts, call Crown Broadcast Service at the following number.
(866) 262-8917
You may also write to the following address:
International Radio & Electronics Corporation 25166 Leer Drive
Elkhart, Indiana, U.S.A. 46514-5425
FM User’s Manual 7-2
Service and support 7 – 3
Crown Broadcast Five Year Limited Product Warranty
SUMMARY OF WARRANTY Crown Broadcast, IREC warrants its broadcast products to the ORIGINAL PURCHASER of a NEW Crown Broadcast product, for a period of (6) years after shipment from Crown Broadcast. All products are warranted to be free of defects in materials and workmanship and meet or exeed all specifications published by Crown Broadcast. Product nameplate with serial number must be intact and not altered in any way. This warranty is non - transferable. This warranty in its entirety is the only warranty offered by Crown Broadcast. No other warranties, expressed or implied, will be enforceable.
EXCLUSIONS Crown Broadcast will not warranty the product due to misuse, accident, neglect and improper installation or operation. Proper installation included A/C line surge supression, lightning protection and proper grounding of the entire transmitter, and any other recommendations designated in the Instruction manual. This warranty does not extend to any other products other than those designed and manufactured by Crown Broadcast. This warranty does not cover any damage to any accessory such as loads, transmission line or antennas resulting from the use or failure of a Crown Broadcast transmitter. Warranty does not cover any loss of revenue resulting from any failure of a Crown Broadcast product, act of God, or natural disaster.
Procedure for Obtaining Warranty Service Crown Broadcast will repair or service, at our discretion, any product failure as a result of normal intended use. Warranty repair can only be performed at our plant facility in Elkhart, Indiana USA or at a factory authorized service depot. Expenses in remedying the defect will be borne by Crown Broadcast, including two-way ground transportation cost within the continental United States. Prior to returning any product or component to Crown Broadcast for warranty work or repair, a Return Authorization (RA) number must be obtained from the Crown Broadcast Customer Service Department. Product must be returned in the original factory pack or equivalent. Original factory pack materials may be obtained at a nominal charge by contacting Crown Broadcast Customer Service. Resolution of the defective product will be made within a reasonable time from the date of receipt of the defective product.
Warranty Alterations No person has the authority to enlarge, amend, or modify this warranty, in whole or in part. This warranty is not extended by the length of time for which the owner was deprived the use of the product. Repairs and replacement parts that are provided under the terms of this warranty shall carry only the unexpired portion of the warranty.
Product Design Changes Crown Broadcast reserves the right to change the design and manufacture of any product at any time without notice and without obligation to make corresponding changes in products previously manufactured.
Legal Remedies of Purchaser
This written warranty is given in lieu of any oral or implied warranties not covered herein. Crown Croadcast disclaims all implied warranties including any warranties of merchantability or fitness for a particular purpose.
Crown Broadcast 25166 Leer Drive
Elkhart, Indiana 46514-5425 Phone 574-262-8900 Fax 977-262-99P9 www.crownbroadcast.com
7–4 FM2000A User's Manual
Notes:
Factory Service Instructions
To obtain factory service, complete the bottom half of this page, include it with the unit, and ship to:
International Radio & Electronics Corporation 25166 Leer Drive
Elkhart, Indiana, U.S.A. 46514-5425
For units in warranty (within 5 years of purchase from any authorized Crown Dealer): We pay for ground UPS shipments from anywhere in the continental U.S. and Federal Express Second Day service from Hawaii and Alaska to the factory and back to you. Expedited service/shipment is available for an additional charge. You may forward your receipt for shipping charges which we will reimburse. We do not cover any charges for shipping outside the U.S. or any of the expenses involved in clearing customs. If you have any questions about your Crown Broadcast product, please contact Crown Broadcast Customer Service at:
Telephone: (866) 262-8917 or (866) 262-8972 Fax: (866) 262-8909
Name: Company: Shipping Address: Phone Number: Fax: Model: Serial Number: Purchase Date:
Nature of the Problem (Describe the conditions that existed when the problem occurred and what attempts were made to correct it.) Other equipment in your system: If warranty has expired, payment will be: Cash/Check VISA Mastercard
Please Quote before servicing
Card Number: Exp. Date: Signature: Return Shipment Preference if other than UPS Ground: Expedite Shipment Other
ENCLOSE WITH UNIT—DO NOT MAIL SEPARATELY
Service and Support 7-5
G–1Glossary
GlossaryThe following pages define terms and abbreviations usedthroughout this and other Crown Broadcast manuals.
A B C
G–2 FM2000A User's Manual
A B CAF Audio Frequency; the frequencies between 20 Hz
and 20 kHz in the electromagnetic spectrum.
ALC Automatic Level Control
AM Amplitude Modulation; the process of impressinginformation on a radio-frequency signal by varyingits amplitude.
bandwidth The range of frequencies available for signalling.
BCD Binary-Coded Decimal; a digital system that usesbinary codes to represent decimal digits.
BFO Beat Frequency Oscillator
BNC A bayonet locking connector for miniature coax;said to be short for Bayonet-Neill-Concelman.
broadband As used in the FM transmitter, refers to the entireaudio spectrum as opposed to the spectrum influ-enced by the pre-emphasis; also called "Wideband."
carrier A continuous signal which is modulated with asecond, information-carrying signal.
crosstalk In FM broadcasting, this term generally refers tothe interaction between the main (L+R) and thesubcarrier (L–R) signals as opposed to "separation"which generally refers to leakage between left (L)and right (R) channels.
density (program) A high average of modulation over time.
deviation The amount by which the carrier frequencychanges either side of the center frequency.
DIP Dual In-line Package; term used to describe an ICor socket that has two parallel rows of pins.
distortion The unwanted changes in signal wave shape thatoccur during transmission between two points.
DPM Digital Panel Meter
EPROM Erasable Programmable Read Only Memory
ESD Electrostatic Discharge; a discharge that ispotentially distructive to sensitive electroniccomponents.
G–3Glossary
exciter (1) A circuit that supplies the initial oscillatorused in the driver stage. (2) A transmitter con-figuration which excludes stereo generation andaudio processing.
FET Field-Effect Transistor
frequency synthesizer A circuit that generates precise frequency signalsby means of a single crystal oscillator in conjunc-tion with frequency dividers and multipliers.
FM Frequency Modulation; the process of impressinginformation on a radio signal by varying its fre-quency.
FSK Frequency Shift Keying; an FM technique forshifting the frequency of the main carrier at aMorse code rate. Used in the on-air identificationof frequencies.
gain reduction The process of reducing the gain of a given ampli-fier.
harmonics Undesirable energy at integral multiples of adesired, fundamental frequency.
HF High Frequency; Frequencies in the 3.0 to 30.0MHz range.
Highband Frequencies affected by the pre-emphasis.
IC Integrated Circuit
I/O Input/Output
LED Light-Emitting Diode
modulation The process by which a carrier is varied to repre-sent an information-carrying signal.
MOSFET Metal Oxide Semiconductor Field Effect Transistor;a voltage-controlled device with high input imped-ance due to its electrically isolated gate.
nearcast A transmission within a localized geographic area(ranging from a single room to a several kilome-ters).
PA Power Amplifier
G–4 FM2000A User's Manual
A B CPAI Power Amplifier Current
PAV Power Amplifier Voltage
pilot A 19–kHz signal used for stereo transmissions.
pre-emphasis The deliberate accentuation of the higher audiofrequencies; made possible by a high-pass filter.
processing The procedure and/or circuits used to modifyincoming audio (keeping its level around 75 kHzdeviation) to make it suitable for transmission.
receiver An option which adds incoming RF capability to anexisting transmitter. See also "Translator."
RF Radio Frequency; (1) A specific portion of theelectromagnetic spectrum between audio-fre-quency and the infrared portion. (2) A frequencyuseful for radio transmission (roughly 10 kHz and100,000 MHz).
SCA Subsidiary Communications Authorization; see"subcarrier."
S/N Signal to Noise
spurious products Unintended signals present on the transmissionoutput terminal.
stability A tolerance or measure of how well a component,circuit, or system maintains constant operatingconditions over a period of time.
stereo pilot See "pilot."
stereo separation The amount of left-channel information thatbleeds into the right channel (or vice versa).
subcarrier A carrier signal which operates at a lower fre-quency than the main carrier frequency and whichmodulates the main carrier.
suppression The process used to hold back or stop certainfrequencies.
G–5Glossary
SWR Standing-Wave Ratio; on a transmission line, theratio of the maximum voltage to the minimumvoltage or maximum current to the minimumcurrent; also the ratio of load impedance tointended (50 ohms) load impedance.
THD Total Harmonic Distortion
translator A transmitter designed to internally change anFM signal from one frequency to another forretransmission. Used in conjunction with terres-trial-fed networks.
satellator A transmitter equipped with an FSK ID option forrebroadcasting a satellite-fed signal.
UHF Ultra High Frequency; frequencies in the 300 to3000 MHz range.
VCO Voltage-Controlled Oscillator
VHF Very High Frequency; frequencies in the 30 to300 MHz range.
VSWR Voltage Standing-Wave Ratio; see "SWR."
Wideband See "broadband."
Index-1
Index
AAAAA
AC Input Board 4–5AC Power 1–3AC power 2–4ALC 3–4, 5–3Antenna 3–7
mismatch 5–5antenna 2–5
BBBBB
Backplane Assembly 4–3Backplane DC Interconnect Board 4–3Board Layouts 6–3
CCCCC
Circuit Breaker 3–4Combiner Board 4–2Connections 2–5Connectors
Hubble Twist Lock® 2–4Hubble Twist-Lock 2–6
connectors 2–5
DDDDD
DC Fuse and Power Distribution Board4–4
DC Output Board 4–6DC Power Switch 3–5Digital Multimeter 3–6, 5–3
EEEEE
Efficiency 1–3efficiency 1–2exciter 1–2
FFFFF
Fans 4–4, 4–6, 5–5Fault Indicators 3–7, 5–5Frequency Range 1–3Fuse Indicators 3–8
HHHHH
Humidity Range 1–3
IIIII
In Ref 3–4, 5–3Input Divider Board 4–3Installation 2–5Interlock Switch 3–5
LLLLL
labels 1–4
MMMMM
Metering and Control Board 4–4multimeter display 3–4
OOOOO
operation 3–2Output Combiner Board 4–3Output Filter & Reflectometer 4–3
PPPPP
PA DC 5–6PA Temp 3–4, 5–4PA Voltage 5–4parts
spares 7–2PFC (Power Factor Correcting)
Switching Board 4–5power adjust 3–3, 3–4Power Consumption 1–3Power Factor 1–3Power Module 4–2Power Out 3–4, 5–3Power Switch 3–4power switch 3–3Power-up 3–2
RRRRR
remote I/O 2–7repair
warranty 7–3RF Drive Requirement 1–3RF Harmonics 1–3
Index-2
RF Output Impedance 1–3RF output power 1–2RF Power Output 1–3RF power output 1–2RU spaces 1–2
SSSSS
S/N Ratio 1–3Safety 1–4Schematics 6–3service
warranty 7–3Service Instructions 7–5Spurious Products 1–3SWR 1–3, 3–4, 5–3
TTTTT
Tot Current 5–4transmitter package 1–2Troubleshooting Flow Chart 5–2
UUUUU
Unpacking 2–2
WWWWW
Warranty 7–3Weight 1–3