fault and attack tolerant control - power systems
TRANSCRIPT
![Page 1: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/1.jpg)
Fault and Attack Tolerant Control - Power Systems
Ian A. Hiskens
University of Michigan
![Page 2: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/2.jpg)
Page 2
Current paradigm: preventive control.
N-1 criterion: operate so system can survive largest credible event.
Future: corrective control.
Use controllable resources to steer the system through (possibly unanticipated) events.
Our focus: cascade mitigation.
Assume the system is transiently (10 second timeframe) stable.
Exploit thermal inertia inherent in transmission line conductors.
Power systems background
5/28/2014
![Page 3: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/3.jpg)
Page 3
Use model predictive control (MPC) to: Control generation, electrical energy storage, wind-spill, FACTS,
load.
Subject to ramp-rate limits, physical limits.
Hierarchical control: Level 1: optimal power flow (with energy storage).
Level 2: MPC drives to set-points determined by Level 1.
Model: Linear formulation, currently use “DC power flow” for network
model.
Convex relaxation of quadratic losses, provably tight at optimal.
Control strategy
5/28/2014
![Page 4: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/4.jpg)
Page 4
IEEE RTS-96 system, double-line outage.
Test case
5/28/2014
![Page 5: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/5.jpg)
Page 5
Test case: max line temperatures
5/28/2014
Base-case: cascade outage, increasing temperatures.
MPC brings temperatures down below limits
AC/DC model inaccuracy causes some minor issues
![Page 6: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/6.jpg)
Page 6
Test case: max line power overloads
5/28/2014
Base-case: cascade outage, large overloads.
MPC manages overloads
AC/DC model is within 10%
![Page 7: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/7.jpg)
Page 7
Test case: aggregate storage injections
5/28/2014
Response to outage: reduce injections.
Returned to optimal set points.
Increase injections to reach SOC set-points.
![Page 8: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/8.jpg)
Page 8
Test case: aggregate load curtailment
5/28/2014
Response to outage: shed some load.
Load curtailment is only necessary initially
![Page 9: Fault and Attack Tolerant Control - Power Systems](https://reader031.vdocuments.mx/reader031/viewer/2022022311/6215b9e14ac5846662051a7d/html5/thumbnails/9.jpg)
Page 9
Test case: MPC cost
5/28/2014