eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 1

EFFICIENT POWER CONVERSIONG

D

SHAL

Maximum Ratings

PARAMETER VALUE UNIT

VDS

Drain-to-Source Voltage (Continuous) 30V

Drain-to-Source Voltage (up to 10,000 5 ms pulses at 150°C) 36

ID

Continuous (TA = 25°C, RθJA = 6°C/W) 90A

Pulsed (25°C, TPULSE = 300 µs) 590

VGS

Gate-to-Source Voltage 6V

Gate-to-Source Voltage -4

TJ Operating Temperature -40 to 150°C

TSTG Storage Temperature -40 to 150

Thermal Characteristics

PARAMETER TYP UNIT

RθJC Thermal Resistance, Junction-to-Case 0.4

°C/W RθJB Thermal Resistance, Junction-to-Board 1.1

RθJA Thermal Resistance, Junction-to-Ambient (Note 1) 42Note 1: RθJA is determined with the device mounted on one square inch of copper pad, single layer 2 oz copper on FR4 board.See https://epc-co.com/epc/documents/product-training/Appnote_Thermal_Performance_of_eGaN_FETs.pdf for details.

All measurements were done with substrate connected to source.

Static Characteristics (TJ = 25°C unless otherwise stated)

PARAMETER TEST CONDITIONS MIN TYP MAX UNITBVDSS Drain-to-Source Voltage VGS = 0 V, ID = 1.3 mA 30 V

IDSS Drain-Source Leakage VGS = 0 V, VDS = 24 V 0.1 1 mA

IGSSGate-to-Source Forward Leakage VGS = 5 V 1 9 mA

Gate-to-Source Reverse Leakage VGS = -4 V 0.1 1 mA

VGS(TH) Gate Threshold Voltage VDS = VGS, ID = 20 mA 0.8 1.4 2.5 V

RDS(on) Drain-Source On Resistance VGS = 5 V, ID = 40 A 1.15 1.45 mΩ

VSD Source-Drain Forward Voltage IS = 0.5 A, VGS = 0 V 1.5 V

EPC2023 – Enhancement Mode Power Transistor

VDS , 30 VRDS(on) , 1.45 mΩID , 90 A

EPC2023 eGaN® FETs are supplied only inpassivated die form with solder bumps. Die Size: 6.05 mm x 2.3 mm

Applications: • High Frequency DC-DC Conversion • Point-of-Load (POL) Converters • Motor Drive • Industrial Automation

Gallium Nitride’s exceptionally high electron mobility and low temperature coefficient allows very low RDS(on), while its lateral device structure and majority carrier diode provide exceptionally low QG and zero QRR. The end result is a device that can handle tasks where very high switching frequency, and low on-time are beneficial as well as those where on-state losses dominate.

eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 2

Dynamic Characteristics (TJ = 25°C unless otherwise stated)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

CISS Input Capacitance

VDS = 15 V, VGS = 0 V

2150 2600

pF

COSS Output Capacitance 1530 2300

CRSS Reverse Transfer Capacitance 100

COSS(ER) Effective Output Capacitance, Energy Related (Note 2)VDS = 0 to 15 V, VGS = 0 V

1850

COSS(TR) Effective Output Capacitance, Time Related (Note 3) 2020

RG Gate Resistance 0.3 Ω

QG Total Gate Charge VDS = 15 V, VGS = 5 V, ID = 40 A 19 25

nC

QGS Gate-to-Source Charge

VDS = 15 V, ID = 40 A

5.7

QGD Gate-to-Drain Charge 3.2

QG(TH) Gate Charge at Threshold 4

QOSS Output Charge VDS = 15 V, VGS = 0 V 30 45

QRR Source-Drain Recovery Charge 0All measurements were done with substrate connected to source.Note 2: COSS(ER) is a fixed capacitance that gives the same stored energy as COSS while VDS is rising from 0 to 50% BVDSS. Note 3: COSS(TR) is a fixed capacitance that gives the same charging time as COSS while VDS is rising from 0 to 50% BVDSS.

500

400

300

200

100

00 0.5 1.0 1.5 2.0 2.5 3.0

I D –

Dra

in Cu

rrent

(A)

Figure 1: Typical Output Characteristics at 25°C

VDS – Drain-to-Source Voltage (V)

VGS = 5 VVGS = 4 VVGS = 3 VVGS = 2 V

I D –

Dra

in Cu

rrent

(A)

VGS – Gate-to-Source Voltage (V) 1.00.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

Figure 2: Transfer Characteristics

500

400

300

200

100

0

25˚C125˚C

VDS = 3 V

25˚C125˚C

VDS = 3 V

4

3

2

1

02.5 3.0 3.5 4.0 4.5 5.0

R DS(o

n) –

Dra

in-to

-Sou

rce R

esist

ance

(mΩ)

VGS – Gate-to-Source Voltage (V)

Figure 3: RDS(on) vs. VGS for Various Drain Currents

ID = 20 AID = 40 AID = 60 AID = 80 A

2.5 3.0 3.5 4.0 4.5 5.0

Figure 4: RDS(on) vs. VGS for Various Temperatures

R DS(

on) –

Dra

in-to

-Sou

rce R

esist

ance

(mΩ

)

VGS – Gate-to-Source Voltage (V)

25˚C125˚C

VDS = 3 V

25˚C125˚C

ID = 40 A

4

3

2

1

0

eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 3

All measurements were done with substrate shortened to source.

Capa

citan

ce (p

F)

0 5 10 15 3020 25

Figure 5a: Capacitance (Linear Scale)

VDS – Drain-to-Source Voltage (V)

4000

3000

2000

1000

0

COSS = CGD + CSD

CISS = CGD + CGS

CRSS = CGD

Capa

citan

ce (p

F)

1000

100

100 5 10 15 2520 30

Figure 5b: Capacitance (Log Scale)

VDS – Drain-to-Source Voltage (V)

COSS = CGD + CSD

CISS = CGD + CGS

CRSS = CGD

Figure 6: Output Charge and COSS Stored Energy

Q OSS

– O

utpu

t Cha

rge (

nC)

E OSS

– C O

SS St

ored

Ener

gy (μ

J)50

40

30

20

10

0

1.0

0.8

0.6

0.4

0.2

0.00 15 20 25 3010 5

VDS – Drain to Source Voltage (V) 0 5 10 15 20

Figure 7: Gate Charge

V GS

– Ga

te-to

-Sou

rce V

olta

ge (V

)

QG – Gate Charge (nC)

ID = 40 AVDS = 15 V

5

4

3

2

1

0

0.50 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

I SD –

Sour

ce-to

-Dra

in Cu

rrent

(A)

VSD – Source-to-Drain Voltage (V)

Figure 8: Reverse Drain-Source Characteristics

500

400

300

200

100

0

25˚C125˚C

VGS = 0 V

Figure 9: Normalized On-State Resistance vs. Temperature

Norm

alize

d On

-Sta

te R

esist

ance

RDS

(on)

2.0

1.8

1.6

1.4

1.2

1.0

0.80 25 50 75 100 125 150

TJ – Junction Temperature (°C)

ID = 40 AVGS = 5 V

eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 4

Figure 12: Transient Thermal Response Curves

Figure 10: Normalized Threshold Voltage vs. Temperature

Norm

alize

d Th

resh

old

Volta

ge

1.40

1.30

1.20

1.10

1.00

0.90

0.80

0.70

0.600 25 50 75 100 125 150

TJ – Junction Temperature (°C)

ID = 20 mA

0.1

1

10

100

1000

0.1 1 10 100

I D – D

rain

Curre

nt (A

)

VDS - Drain-Source Voltage (V)

Limited by RDS(on)

Pulse Width

1 ms

100 µs

Figure 11: Safe Operating Area

tp, Rectangular Pulse Duration, seconds

Z θJB

, Nor

mal

ized T

herm

al Im

peda

nce

0.5

0.050.02

Single Pulse

0.01

0.1

Duty Cycle:

Junction-to-Board

Notes:Duty Factor: D = t1/t2

Peak TJ = PDM x ZθJB x RθJB + TB

PDM

t1

t2

10-5 10-4 10-3 10-2 10-1 1 10+1

1

0.1

0.01

0.001

0.0001

0.5

0.050.02

Single Pulse

0.01

0.1

Duty Cycle:

0.2

tp, Rectangular Pulse Duration, seconds

Z θJC

, Nor

mal

ized T

herm

al Im

peda

nce

0.5

Junction-to-Case

Notes:Duty Factor: D = t1/t2

Peak TJ = PDM x ZθJC x RθJC + TC

PDM

t1

t2

10-6 10-5 10-4 10-3 10-2 10-1 1

1

0.1

0.01

0.001

0.0001

eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 5

DIE MARKINGS

DIE OUTLINESolder Bump View

Side View (685

)

Seating plane

(785

)

100 ±

20

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29

A

f

d X30

B

gX4e

c

X30

X28

Pad 1 is Gate;Pads 2 ,5, 6, 9, 10, 13, 14, 17, 18, 21, 22, 25, 26, 29 are Source;Pads 3, 4, 7, 8, 11, 12, 15, 16, 19, 20, 23, 24, 27, 28 are Drain;

Pad 30 is Substrate.*

*Substrate pin should be connected to Source

DIM

Micrometers

MIN Nominal MAX

A 6020 6050 6080B 2270 2300 2330c 2047 2050 2053d 717 720 723e 210 225 240f 195 200 205g 400 400 400

YYYY2023

ZZZZ

TAPE AND REEL CONFIGURATION8 mm pitch, 12 mm wide tape on 7” reel

7” inch reel Dieorientationdot

Gatesolder bump isunder thiscorner

Die is placed into pocketsolder bump side down(face side down)

Loaded Tape Feed Direction

a

d e

f g

h

c b

Part Number

Laser Markings

Part #Marking Line 1

Lot_Date CodeMarking Line 2

Lot_Date CodeMarking Line 3

EPC2023 2023 YYYY ZZZZ

DIM Dimension (mm)EPC2023 (Note 1) Target MIN MAX

a 12.00 11.90 12.30b 1.75 1.65 1.85c (Note 2) 5.50 5.45 5.55d 4.00 3.90 4.10e 8.00 7.90 8.10f (Note 2) 2.00 1.95 2.05g 1.50 1.50 1.60h 1.50 1.50 1.75

Note 1: MSL 1 (moisture sensitivity level 1) classified according to IPC/JEDEC industry standard.

Note 2: Pocket position is relative to the sprocket hole measured as true position of the pocket, not the pocket hole.

2023

YYYY

ZZZZ Die orientation dot

Gate Pad bump isunder this corner

eGaN® FET DATASHEET EPC2023

EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2020 | | 6

RECOMMENDEDLAND PATTERN (units in µm)

RECOMMENDEDSTENCIL DRAWING (units in µm)

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29

6050

18070

0X3

0

2300

400

2030

X30

X28

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

6050

400X34

2300

1330

2050

720

200X35

R601 3 5 7 9 11 13 15 17 19 21 23 25 27 29

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

Information subject to change without notice.

Revised June, 2020

Recommended stencil should be 4 mil (100 µm) thick, must be laser cut, openings per drawing.

Intended for use with SAC305 Type 3 solder, reference 88.5% metals content.

Additional assembly resources available at https://epc-co.com/epc/DesignSupport/ AssemblyBasics.aspx

Efficient Power Conversion Corporation (EPC) reserves the right to make changes without further notice to any products herein to improve reliability, function or design. EPC does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others.

eGaN® is a registered trademark of Efficient Power Conversion Corporation.EPC Patent Listing: epc-co.com/epc/AboutEPC/Patents.aspx

Land pattern is solder mask definedSolder mask opening is 180 µmIt is recommended to have on-Cu trace PCB vias

Pad 1 is Gate;Pads 2, 5, 6, 9,10,13,14, 17, 18, 21, 22, 25, 26, 29 are Source;Pads 3, 4, 7, 8, 11, 12, 15, 16, 19, 20, 23, 24, 27, 28 are Drain;

Pad 30 is Substrate.*

*Substrate pin should be connected to Source