energy flows and balances. units of measure btu – amount of energy required to heat one pound of...
TRANSCRIPT
![Page 1: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/1.jpg)
Energy Flows and Balances
![Page 2: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/2.jpg)
Units of Measure
BTU – amount of energy required to heat one pound of water, one degree Fahrenheit
Calorie – amount of energy required to heat 1 ml water 1 degree Celsius
![Page 3: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/3.jpg)
Energy Balances and Conversion
The form of the available energy is often not the form that is the most useful so it is common to have to convert one form of energy to another.
Water in lake – turbine – electricity – light and heat
Bio-mass – combustion – steam - generator - electricity
Wind – windmill – generator - electricity
Conversion always less than 100% efficient
![Page 4: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/4.jpg)
Since energy “flows” can use the same concepts as materials balance to analyze
Rate ofEnergy
accumulated
Rate of Energy
In
Rate ofEnergy
Out
Rate of Energy
Generated= - +
At Steady-State
0
Rate ofEnergy
In
Rate ofEnergy
Out
Rate of EnergyWasted
= -
Efficiency:
Useful energy Out
Energy InX 100
![Page 5: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/5.jpg)
Bomb Calorimeter
![Page 6: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/6.jpg)
Calorimeter Example
A calorimeter holds 4 liters of water. When a 10 gram sample of a waste-derived fuel is combusted the result is a 12.5o C rise in temperature. What is the energy value of the fuel?
Energy In = Energy Out
(The idea behind a calorimeter is that no energy is wasted. It is all captured in the device.)
Energy Out = 12.5o C x 4 L x 103 ml/L x 1 g/ml
= 50 x 103(0C). G, or calories
= 50 x 103 calories x 4.18 (J/cal) = 209 x 103 J
Energy In = 209 x 103 J
Energy Value of the Fuel = (209 x 103 J/g)/ (10 g) = 20,900 J/g
![Page 7: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/7.jpg)
Heat Energy
HeatEnergy
Mass ofMaterial
Absolute TemperatureOf the Material
= X
This is only true when the heat capacity of the material is independent of temperature. In particular when a phase change occurs this is not true. (Water to Steam)
Energy Balance at Steady-State with two inflows
0 = Heat Energy In - Heat Energy Out + 0
0 = [T1Q1 + T2Q2] - T3Q3
T3 = [T1Q1 + T2Q2] / Q3
Also: Q3 = Q1 + Q2
![Page 8: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/8.jpg)
Example
A coal-fired power plant discharges 3 m3/sec of cooling water at 80o C into a river that has a flow of 15 m3/sec and a temperature of 20o C. What will the temperature of the river be immediately downstream of the discharge?
T3 = [T1Q1 + T2Q2] / Q3
= [(80 + 273)(3) + (20 +273)(15)] / (3 + 15)
= 303oK = 30o C
![Page 9: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/9.jpg)
Energy Sources and Availability
Non-Renewable Sources
Nuclear PowerCoal, Peat, and Similar ProductsOilNatural Gas
Renewable Sources
Hydropower from RiversHydropower from TidesWood and Other Bio-massSolar PowerRefuse and other WastesWind
![Page 10: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/10.jpg)
What responsibility do we have to future generations?
![Page 11: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/11.jpg)
Energy Equivalence
Arithmetic Energy Equivalence – based on energy amounts only
Conversion Energy Equivalence – takes into account the energy loss in conversion
For ExampleIf gasoline has an energy value of 20,000 BTU/lb and refuse-derived fuel has an energy value of 5,000 BTU/lb, the arithmetic energy equivalence is:
20,000/5,000 = 4 lb refuse / 1 lb gasoline
It has been estimated that 50% of the energy in refuse derived fuel is required for processing, therefore, the actual net energy in the refuse is 2,500 BTU/lb. So:
Conversion energy equivalence = 20,000 / 2,500 = 8 lb refuse / 1 lb gasoline
![Page 12: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/12.jpg)
Electric Power Production
Present power plans are less than 40% efficient
![Page 13: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/13.jpg)
Simplified:
Heat Engine
Energy Balance
Rate ofEnergy
accumulated
Rate of Energy
In
Rate ofUseful
Energy Out
Rate of Wasted
Energy Out= - -
0, S.S.
0 = Qo - QU - QW
Efficiency (%) = QU/Qo
![Page 14: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/14.jpg)
The most efficient engine possible is called a Carnot Engine. Its efficiency is calculated as:
EC(%) = (T1 – To)/T1 x 100
Where: T1 = absolute temperature of the boilerT2 = absolute temperature of the cooling water
Since this is the best possible:
(QU/Qo) < (T1 – To)/T1
Typical conditions for a power plant are: T1 = 600 + 273 = 873, and T0 = 20 + 273 = 293
EC = (873 – 293) / 873 = 66%
Because real power plants have many other types of energy losses (heat in stack gases, evaporation, friction) their actual efficiency is about 40%. This figure is confirmed by operational data.
![Page 15: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/15.jpg)
Where does all of this energy go?
All of it is dissipated in some way into the environment
60% of the energy content of the fuel that comes into the plant is released to the environment as heat
15% stack gases, 45% cooling water
Thermal pollution
![Page 16: Energy Flows and Balances. Units of Measure BTU – amount of energy required to heat one pound of water, one degree Fahrenheit Calorie – amount of energy](https://reader035.vdocuments.mx/reader035/viewer/2022070406/56649de95503460f94ae392e/html5/thumbnails/16.jpg)
Cooling this water before discharge is a significant problem
Cooling towers such as these can add up to 250% to the cost of a nuclear power plant
Why is it better to allow this heat to be discharged to the atmosphere rather than to a water body?
What else could you do with this heat?