emerson 543 restoration and cabinet repair

7/18/2019 Emerson 543 Restoration and Cabinet Repair

http://slidepdf.com/reader/full/emerson-543-restoration-and-cabinet-repair 1/11

Emerson Model 543 AC/DC Radio Set

by Donald Sentz

Fall/Winter 2011

My mom obtained this set for me in Alabama, sometime in the

early 1990’s, and shipped it to me. There was a horizontal break

in the Bakelite case on the right side, and duct tape residue.

The original speaker had been replaced with another one that was

not physically fastened to the chassis. It had one of its

original knobs but it was missing the shaft mate insert.

I found two other knobs in my junk boxes, one brown and one

black, that look OK. I repainted the grill and installed a

speaker soon after I got the set. I used “Whiteout” to refill

the Emerson logo on the enclosure. I did not replace any

internal parts except for the electrolytics. The dial

calibration was way off and the set would “motorboat” at the low

end of the dial. I put the set away, hoping to one day have time

to figure out what was wrong and fix it.

Right after I retired, in the summer of 2010, I performed a

thorough electrical restoration. I changed the speaker yet

again, installed all new capacitors and several new resistors.

The motorboating and dial calibration issues were due to the

I.F. alignment being way off. I realigned the set using my

Heathkit SG-8 signal generator and certain radio stations of



known frequency. Since Bakelite is tricky to repair I used a

single long strip of clear cellophane tape to temporarily

reinforce the break. The set works really great now. It easily

picks up KFBK 1530 in Sacramento at night, from our house on

west side of Los Angeles. Also KERN-1180 in Bakersfield usually

comes in at night pretty good.

Here is a photo detail of the

replacement speaker mounting. I

used the spool from a roll of

Teflon plumber’s tape. The

speaker magnet fits nicely inside

the hub of the spool after

stuffing the gap with a piece of

screen window weather-strip. I

used an Exacto knife to “drill”

the mounting holes in the soft

plastic spool flange. I used twoceramic standoffs to mount the

spool to the original speaker

bracket. Finally I installed a

stiff wire brace from the top of

the spool flange to the speaker

bracket.



Chassis View Showing New Parts Installed.

During the 2010 work I reverse engineered the circuit to produce

the complete schematic shown below and also on the last page of

this report.



January 7, 2012- I found and downloaded a scan of the Riders

schematic for this set (see next to last page of this report).

There are four minor differences between my set’s present wiring

and the Rider’s diagram;

My set came to me with a 39 ohm resistor installed for R11instead of the Riders’ 15 ohm 1 watt part. Also, there was

no series resistor R10 for my pilot light. It is possible

that the original pilot light may have been something other

than a #47, and a repairman may have modified the set for a

#47 pilot light.

During restoration I did not have the Riders diagram, and I

could not figure out why someone had apparently wired pin 4

of the 12SQ7 to the AVC line. This appeared to be a “do

nothing” connection. Most other sets I have studied tie pin

4 to the cathode, which is also “do nothing”. Absent

Rider’s, I chose to connect pin 4 of the 12SQ7 to pin 3(cathode).

I connected the new 250mmF RF bypass capacitor C13 to B-,

to be consistent with other sets. Rider’s shows it

connected to chassis. It should not matter which way it is

connected, since C19 connects any RF signals on B- to

chassis. My C19 is .22uF instead of the .02uF of Riders.

My set did not have capacitor C9. The original back cover

was missing from my set. I suspect that C9 may have been on

the original back cover, along with a pair of screw

terminals for the external antenna and ground connections.



July 26, 2013- Four days ago I finally attempted to repair the

break in the cabinet that I mentioned in the 1st paragraph of

this report.

I made an adjustable clamp using two wood lath strips, a pieceof cushioning foam, two pieces of #12 insulated copper wire, and

two machine screws and nuts. I placed the foam underneath the

top strip in order to distribute the compression force and

protect the top of the cabinet. I aligned the top and bottom

edges of the break while tightening the clamp. See Figure 1.

Figure 1: Cabinet Clamped, but the Front, Back and Side Tape

Strips not yet applied

I used #150 grit sandpaper to roughen up the inside of the

cabinet on both sides of the break. I used acetone to wipe the

inside of the cabinet on both sides of the break. I attached

strips of masking tape to the front and back edges of thecabinet at the break. These tape strips acted as “dams” to

prevent the liquid epoxy from flowing over the cabinet edges

before it cures. I also applied a strip of clear Scotch tape all

along the break, on the outside of the cabinet. The purpose of

this strip is to contain any epoxy that seeps into the seam of

the break.



For the repair operation I set the cabinet clamp onto two stacks

of books as shown in Figure 2 (I took this picture after the

repair operation, so the tape strips were already removed, and

also I had spread out a newspaper sheet to protect the books and

the table top).

Figure 2: Cabinet in Position for Repair Operation

I then used an old toothbrush to dab on a lamination of “Liquid

Wood” epoxy (Figure 3) layered with seven 3” x 2½” pieces of“Art Paper” that is black on one side and white on the other

side. The freshly mixed Liquid Wood is quite runny, so the tape

strip “dams” are very important to prevent it from flowing over

the cabinet sides.



Figure 3: Abatron LiquidWood Epoxy

I applied a total of seven paper layers, spreading epoxy between

each layer. I did not apply epoxy to the top side of the last

layer. See Figure 4 showing the repair after partial curing.

Figure 4: Partially Cured Repair

I removed the three tape strips about an hour after completing

the repair operation. If you don’t wait about an hour the epoxy

might flow over the edge, but if you wait too long the tapes

will stay glued to the cabinet. I used acetone to wipe some

epoxy residue off the outside of the cabinet along the seam of

the break. After one day of curing in position I placed the

cabinet over a 15 watt incandescent light bulb to heat up the

repaired area to about 120 degrees or so. This greatly speeds up

the curing process.

I removed the clamp and reassembled the set after about 10 hoursof elevated temperature cure, spread over three days. The repair

appears to be very rigid and strong. Figure 5 shows the set

after the repair.



Figure 5: Cabinet Repair Completed



THE END

emerson 543 restoration and cabinet repair

Documents