effect of process variables in abrasive flow machining · effect of process variables in abrasive...
TRANSCRIPT
International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 3, Issue 2, February 2013)
Effect of Process Variables in Abrasive Flow Machining
Jose Cherian1, Dr Jeoju M Issac
2
1Research Scholar, Karpagam University, Eachanari Post, Coimbatore-641021
2Professor, Department of Mechanical Engineering, MA College of Engineering Kothamangalam, Kerala, India.
Abstract: In abrasive flow machining (AFM), an abrasive
mixture and a polymer of special rheological properties is
forced through a restricting medium. This results the
abrasive mixture and the polymer to act as a self-forming tool
which precisely removes the material of the work piece and
improves the surface finish. It is capable of machining areas,
which are difficult to reach by conventional machining and
can be used to machine and improve surface finish of internal
parts of intrigue shapes. The work piece hardness, abrasive
size, abrasive hardness, extrusion pressure and properties of
carrier are the important process parameters that affect the
performance of AFM. The objective of the present paper is to
study the effect of process variables on surface finish and
material removal.
Keywords— Abrasive flow machining, Material removal, Silly Putty, soft materials, Surface finish.
I. INTRODUCTION
Manufacturing process demands approximately 15% of
the total manufacturing cost for finishing operations. When
the surface roughness value is less than one micron, the
cost of surface finishing operation again increases sharply.
AFM is developed as a method to improve the surface
finish of components have complicated irregular
shape/profile, rough internal surface, cavity and undercut. It
is also capable of improving the productivity and
performance of the components. AFM process has a greater
potential to deburr, radius, polish and remove recast layer
of components in a wide range of applications.
AFM was developed by Extrude Hone Corporation; USA in 1960s.The abrasion ability of abrasive media is governed by many factors, especially by grain size, abrasive concentration, extrusion pressure and hardness of work piece material. In order to analyze the influence of
such parameters and other AFM conditions upon material removal and surface finish many experimental investigations were conducted and formed models for the same [1-2].Experimental investigations [3-5] discuss the
effect of process parameters such as extrusion pressure, number of cycles, viscosity, abrasive concentration and grain size on the process performance parameters, such as surface finish and material removal during AFM.
Williams and Rajurkar [6] used the full factorial design
for experimentation and studied the effect of medium viscosity and extrusion pressure on material removal rate
and surface finish. Jain and Adsul [7] reported that initial
surface roughness and hardness of the work piece are important parameters affecting the material removal rate in
AFM. Loveless [8] studied the effect of viscosity of media
on surface finish. They found that viscosity is the only parameter which significantly affects the surface finish.
They found the relationship between initial surface finish and percentage improvement in surface finish is non-linear.
Singh and Shan [9] applied a magnetic field around the
work piece and observed that the presence of magnetic field significantly improves the surface finish and material
removal. This improvement is mainly due to the increased
concentration of abrasive at the machining surface. The objective of the present paper is to analyze the effect of
extrusion pressure, grain size, abrasive concentration on
material removal and surface finish.
II. PROCESS MODELLING AND OPTIMIZATION
Williams and Rajurkar [6] developed a stochastic model of AFM generated surfaces by Data Dependent systems (DDS) methodology. They have estimated the ratio of
surface roughness peak height (RZ) to the centerline
average surface roughness value (Ra) by DDS methodology and found to be between 1.4 and 2.2 micrometers for the AFM process. It was established in their research that AFM finished surface profiles possess two distinct wavelengths, a large wavelength, that corresponds to the main path of the abrasive while the small wavelength is associated with the cutting edges. Good agreement is found between the primary frequency ranges obtained in the DDS modeling and those derived from spectral analysis function. It is found that these frequency bands are related to different material removal modes in AFM. Consequently, the mechanism of material removal is considered to consist of ploughing responsible for the creation of characteristic flow lines and micro cutting. They proposed an expression for estimating the
abrasive grain wear and the number of active grains(Cd).
The estimated value of Cd can be used as a cutting life
criterion for abrasives. 554
International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 3, Issue 2, February 2013)
For small number of cycles, its value should remain
fairly stable but with more and more processing, the abrasive particles may fracture and thereby increasing the Cd value. The downturn of Cd value indicates that the medium has been absorbed too much abrasives and needs replacement. Jain et al.[10] also carried out simulation of finished surface profiles and material removed considering the interaction of abrasive grain with work piece material.
Rajeshwar et al.[11] proposed a mathematical simulation model to determine the characteristics of the medium flow during finishing and its experimental verification was carried out. This model was developed using constitutive equations of Maxwell model, considering the medium characteristics as non-Newtonian flow. They reported that a linear relationship exists between shear stress acting on the surface and the layer thickness of material removed.
III. EXPERIMENTAL AFM SET-UP
The fig.1 shows the abrasive flow machining set up. AFM works on the principle of back and forth flow of a compound against the work piece. This leads to the improvement in the surface finish of the work piece. The compound used here is an abrasive (SiC) mixed with silly putty. Work piece is placed inside the work holding device and the dynamometer is placed in between the two opposite piston cylinder arrangement. The surfaces and edges of the work piece are finished by the flowing medium across the work piece to be finished. The tooling, also called as fixture arrangement, holds the work piece in position and directs the abrasive medium to the appropriate areas of the work piece that is to be machined.
When extrusion pressure is applied to the medium by the
piston two types of forces are generated, axial and radial. A two component dynamometer is used to measure these forces. The medium used for experimentation is natural rubber.
IV. EXPERIMENTAL RESULTS.
It seems to indicate that for surface finish to improve the
extrusion pressure must be at a higher level. At lower level of extrusion pressure, low abrasive concentration level and smaller grain size, the surface finish value diminishes. Also low extrusion pressure and larger grains seem to provide uneven distribution of grains resulting in significant variation in the surface finish. The improved surface finish can be achieved only through an optimum combination of three parameters-extrusion pressure, grain mesh number and abrasive concentration.
TABLE I
Model term Effect estimate Sum of squares Percent contribution
A’ 9.820 192.865 8.45
B’ 12.65 320.298 14.03
C’ 24.787 1228.840 53.85
A’B’ 0.022 0.001 0.000043
A’C’ 1.672 5.595 0.245
B’C’ 16.037 514.403 22.54
A’B’C’ 3.157 19.94 0.873
The main effects of extrusion pressure (A’),grain mesh
number (B’) and abrasive concentration(C’) and their interaction on average percentage reduction in surface roughness are given in Table1.All the three factors must be kept high to maximize the average percentage reduction in surface roughness.
The interaction effects are shown in the Table1.The
interactions A’B’, A’C’ and B’C’ are plotted in fig2, fig3 and fig4. It is seen that figure2 and fig3 are almost parallel. Hence there is no interaction effect between A’&B’ and A’&C’.Their percentage contribution is also insignificant.
555
Fig 2
Fig 5
Fig 4
Fig 7
Ave
rage
pe
rce
nt
red
uct
ion
in R
a
Extrusion Pressure (A’)
Ave
rage
pe
rce
nt
red
uct
ion
in R
a
Ave
rage
pe
rce
nt
red
uct
ion
in R
a
Abrasive Concentration (C’)
Grain mesh number (B’)
International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 3, Issue 2, February 2013)
Larger interspacing between the grains will lead to
reduction in medium stiffness. These will cause high variability in percent reduction in Ra with larger grains. At high extrusion pressure and high grain mesh number more grains will be present in a unit area causing reduced interspacing and increased stiffness of the medium. The net result of these will be low variability in percent reduction in Ra. At Low abrasive concentration, less grain will come in contact with the work piece causing low variation in percent reduction Ra.
The figures 8 to 10 show the variance of interaction between A’B’ and A’C’ and B’C’. It is clear that A’ and B’ are highly interactive. Fig 9 shows the interaction effect of B’C’ on the variance of percent reduction in Ra.
4.1 Effect of Main Process Variables
Main effects plot for variance of percentage reduction in Ra are plotted in fig (5) to fig(7)
Main effect plots are given figure5,fig6 and fig 7. At low
grain mesh number, grains are big and less number of grains are accommodated in unit area.
V. RESULTS AND DISCUSSION
The average percent reduction in surface roughness can be increased by keeping the extrusion pressure, grain mesh number and Abrasive concentration at high levels, while the average force ratio is able to be increased by keeping extrusion pressure and abrasive concentration at a high level and grain mesh number at a low level.
556
Fig 3
Fig 6
Fig 10
International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 3, Issue 2, February 2013)
Also from experiments it is clear that when the force
ratio is maximum, the percentage reduction in surface roughness is also maximum. The correlation coefficient between average percent reduction in surface roughness and average force ratio are higher as compared to correlations of average percentage reduction in surface roughness with average axial and radial forces.
REFERENCES
[1] M.Barletta. 2005. A new technology in surface finishing: Fluidized
bed machining (FBM) of aluminum alloys. Journal of Materials processing Technology 173(2006) 157-165
[2] Jain R K, Jain V.K, Dixit P.M; Modeling of material removal and surface roughness in Abrasive flow machining. International journal of Machine tool and manufacture. 30(1999) 1903-1923.
[3] Rhoades L.J; “Abrasive flow machining with not-so-silly putty”, Metal Finishing, July, 1987,27-29
[4] Rhoades L.J;”Abrasive Flow Machining” Manufacturing
Engineering, Nov;1988 75-78 [5] Rhoades L.J”Abrasive flow machining A case study” Material
processing Technology,28,1991,107-116 [6] Williams R.E.and Rajurkar K.P. “Stochastic modeling and analysis
of Abrasive flow machining”, Transaction ASME, Journal of Engineering for Industry,114,1992,74-78
[7] Jain V.K; Adsul. S.G; “Experimental investigations into abrasive flow machining “International Journal of Machine tool and Manufacturing,40,2002,1003-1021
[8] Loveless T.R, Williams R.E and Rajurkar K.P;”A study of the effects of Abrasive Flow finishing on various machined surfaces. Journal Material processing technology, 47, 1994,133-151.
[9] Sing S.Shan H.S; Development of magneto abrasive flow machining
process, International Journal of Machine Tool and Manufacture,42,2002,953-959.
[10] Jain R.K; Jain V.K;Dixit P.M; Modeling of Material removal and surface finish in Abrasive Flow Machining, International journal of Machine Tool and Manufacture 39(1999),1903-1923.
[11] Rajeswar G;Kozak J;Rajurkar K.P; Modeling and computer simulation of media flow in abrasive flow machining process, Proceedings of the International Mechanical Engineering Congress and exposition Chicago,PED,68,(1994),pp.965-971.
557
Fig 8
Fig 9