edc manual
TRANSCRIPT
-
7/28/2019 Edc Manual
1/47
Electronic Devices and Circuits EEE
1
I CYCLE EXPERIMENTS
-
7/28/2019 Edc Manual
2/47
Electronic Devices and Circuits EEE
2
Symbolic representation of PN Junction Diode
Circuit Diagram:
Fig-1 Diode under forward bias condition
Fig-2 Diode under reverse bias condition
-
7/28/2019 Edc Manual
3/47
Electronic Devices and Circuits EEE
3
-No:
Date:
CHARACTERISTICS OF PN JUNCTION DIODE
Aim:
To study and plot volt-ampere characteristic of PN Junction Diode and determine its
Q-point and dynamic resistance.
Apparatus Required:
S. No Items Range Type Quantity
1 Diode IN4007 1
2 Regulated Power supply 0-30V Single 1
3 Ammeter 0-50mA MC 1
4 Voltmeter
(0-10)V
(0-1)V MC 1
5 Bread Board 1
6 Connecting Wires Single strand as req.
Formula used:Static Resistance, R=Vf/If
Dynamic Resistance, r =Vf/If
To find DC Load Line: E= (RfIf) +Vd
Theory:
Forward Bias Condition:
When positive terminal of the battery is connected to the P type and the negative
terminal to N type of the PN junction diode, the bias applied is known as forward bias.
Operation:
The applied potential with the external battery acts in opposition to the internal
potential barrier. The applied positive potential repels the holes in P type region so that the
holes move towards the junction and the applied negative potential repels the electrons in the
N type region and the electrons move towards the junction. Eventually, when the applied
potential is more than the internal barrier potential, the depletion region and internal potential
barrier disappear.
-
7/28/2019 Edc Manual
4/47
Electronic Devices and Circuits EEE
4
At the cut in voltage or threshold voltage (V r), the potential barrier is overcome and
the current through the junction starts to increase rapidly.
Model graph:
Tabulation:
Forward bias: Reverse bias:
S. No Voltage (Vf)
in volts
Current (If)
in mA
S.No Voltage (Vr)
in volts
Current (Ir)
in uA
-
7/28/2019 Edc Manual
5/47
Electronic Devices and Circuits EEE
5
Reverse bias condition:
When the negative terminal of the battery is connected to the P type and the positive
terminal to the N type of the PN junction diode, the bias applied is known as reverse bias.
Operation:
Under applied reverse bias, holes which form the majority carriers of the P side move
towards the negative terminal of the battery and electrons which forms the majority carriers
of the N side are attracted towards the positive terminal of the battery. Hence, the width of
the depletion region which is depleted of mobile charge carriers increases. Thus, the electric
field produced by applied reverse bias, is in the same direction as the electric field of the
potential barrier.
Therefore no current flows in the external circuit. Consequently, the minority carriers
will flows towards their majority carrier side gives rise to small reverse current. This current
is known as reverse saturation current, Io.
Once the electric field intensity increases beyond a critical level, the p-n junction
depletion zone breaks-down and current begins to flow, usually by either the Zener or
avalanche breakdownprocesses.
http://en.wikipedia.org/wiki/Zener_breakdownhttp://en.wikipedia.org/wiki/Avalanche_breakdownhttp://en.wikipedia.org/wiki/Avalanche_breakdownhttp://en.wikipedia.org/wiki/Zener_breakdown -
7/28/2019 Edc Manual
6/47
Electronic Devices and Circuits EEE
6
-
7/28/2019 Edc Manual
7/47
Electronic Devices and Circuits EEE
7
Procedure:
Forward bias:
Connections are made as per the circuit diagram fig-1. Input voltage is varied corresponding diode voltage and current readings are
tabulated.
V-I characteristic of diode under forward bias condition is plotted.Reverse bias:
Connections are made as per the circuit diagram fig-2. Input voltage is varied corresponding diode voltage and current readings are
tabulated. V-I characteristic of diode under reverse bias condition is plotted.
Viva Questions:
1. What is meant by PN junction diode?2. What is meant by barrier potential and threshold voltage?3. What are the different types of breakdown occur in diode?4. Give the expression for diode current equation and width of the depletion region.5. What are the classifications of semiconductor devices?6. What is meant by transient capacitance and diffusion capacitance?
Result:
-
7/28/2019 Edc Manual
8/47
Electronic Devices and Circuits EEE
8
Symbolic representation of Zener Diode
Circuit Diagram:
Under Forward Bias Condition:
Under Reverse Bias Condition:
-
7/28/2019 Edc Manual
9/47
Electronic Devices and Circuits EEE
9
Ex-No:
Date:
CHARACTERISTIC OF ZENER DIODE
Aim:
To study and plot volt-ampere characteristic of Zener Diode and find its dynamic
resistance.
Apparatus Required:
S. No Items Range Type Quantity1 Zener Diode Z 6V8 1
2 Regulated Power supply 0-30V Single 1
3 Ammeter 0-50mA MC 1
4 Voltmeter 0-10V MC 1
5 Bread Board 1
6 Connecting Wires Single strand as req.
Theory:
Zener diode is a special diode operating in the breakdown region of the ordinary
diode. This diode is heavily doped when compared to ordinary diode. It exhibits almost the
same properties, except the device is special in the reverse direction if the voltage is larger
than the breakdown voltage known as "Zener knee voltage" or "Zener voltage".
They are widely used to regulate the voltage across a circuit. When connected in
parallel with a variable voltage source so that it is reverse biased, a Zener diode conducts
when the voltage reaches the diode's reverse breakdown voltage.
http://en.wikipedia.org/wiki/Breakdown_voltagehttp://en.wikipedia.org/wiki/Breakdown_voltage -
7/28/2019 Edc Manual
10/47
Electronic Devices and Circuits EEE
10
Model Graph:
Tabulation:
Forward bias Condition:
S.No Voltage (Vf) in
volts
Current (If) in
mA
Reverse Bias Condition:
S.No Voltage (Vr) in
volts
Current (Ir) in mA
-
7/28/2019 Edc Manual
11/47
Electronic Devices and Circuits EEE
11
Procedure:
Forward Bias:
Connections are made as per the circuit diagram. Input voltage is varied corresponding diode voltage and current readings are
tabulated.
V-I characteristic of diode under forward bias condition is plotted. Find the dynamic resistance r =Vf/If
Reverse Bias:
Connections are made as per the circuit diagram. Input voltage is varied corresponding diode voltage and current readings are
tabulated.
V-I characteristic of diode under reverse bias condition is plotted. Find the dynamic resistance r = Vz/ Iz.
Result:
-
7/28/2019 Edc Manual
12/47
Electronic Devices and Circuits EEE
12
Circuit Diagram:
Half Wave Rectifier without Filter:
Half Wave Rectifier with Filter:
-
7/28/2019 Edc Manual
13/47
Electronic Devices and Circuits EEE
13
Ex. No.:
DATE:
SINGLE PHASE HALF WAVE RECTIFIER WITH AND WITHOUT FILTER
Aim:
To obtain DC signal from AC signal by using half wave rectifier without and with
filter and obtain ripple factor and Efficiency.
Materials Required:
S No Item Range Specification Qty
1. Diode IN4007 1
2. Transformer 230V/(09)V 1
3. CRO 030 MHz 1
4. Resistor 1k 1
5. Bread board 1
6. Ammeter 0-50mA MC 1
7. Voltmeter 0-30V MC 1
8. Connecting wires Single stand As req.
9. Capacitor 22 F 1
Theory:
In a HWR, the diode is forward biased only during the positive half cycle of the input
signal. The diode conducts and current flows through the load only for the positive half cycle
of input voltage. During the negative half cycle the diode is reversed biased and the diode
behaves as an open circuit. Hence there is no current flow through the load. The output DC
signal is the pulsating DC signal. By using the basic capacitive filter we can convert the
pulsating DC into pure DC signal.
When no filter circuit is present output voltage Vdc = Vm/
The RMS value of the secondary voltage of the transformer is V rms = Vm/2.
Formula Used:
The output DC power Pdc = VdcIdc
The output AC power Pac=VrmsIrms
Efficiency()= Pdc/ Pac
Form Factor(FF)= Vrms/Vdc
Ripple Factor = [(Vrms/ Vdc)21]1/2 or [(FF2-1)]1/2
Transformer Utilization ratio(TUF)= Pdc/VsIs
Where,Vs & Is are rms voltage and rms current of the transformer secondary respectively
-
7/28/2019 Edc Manual
14/47
Electronic Devices and Circuits EEE
14
Model Graph:
Input Wave Form:
Output Wave Form without Filter:
-
7/28/2019 Edc Manual
15/47
Electronic Devices and Circuits EEE
15
Procedure:
1. The circuit connections are given as per the circuit diagram.2. The supply voltage is switched on.3. The DC voltage and current are noted down.4. By using the CRO observe the wave forms.5. From the tabulated reading find the ripple factor and Efficiency
Viva Questions:
1. What is rectifier?2. Explain the following terms:
I. Ripple factorII. Peak Inverse Voltage
III. Average voltage and currentIV. Rectifier efficiencyV. Ripple voltage
3. What is the main disadvantage of HWR?4. What is called % regulation?
Result:
-
7/28/2019 Edc Manual
16/47
Electronic Devices and Circuits EEE
16
Output Wave Form with
Filter:
Tabulation:
Without filter:
Vm(V) Vrms(V) Vdc(V) Ripple factor Efficiency
With filter:
Vm(V) Vrms(V) Vdc (V) Ripple factor Efficiency
-
7/28/2019 Edc Manual
17/47
Electronic Devices and Circuits EEE
17
Circuit Diagram:
Full Wave Rectifier without Filter:
Center tap transformer
230V/(12V-0V-12V)
Full Wave Rectifier with Filter:
Center tap transformer
230V/(12V-0V-12V)
-
7/28/2019 Edc Manual
18/47
Electronic Devices and Circuits EEE
18
Ex. No.:
DATE:
SINGLE PHASE FULL WAVE RECTIFIER WITH AND WITHOUT FILTER
Aim:
To obtain DC signal from AC signal by using half wave rectifier without and with
filter and obtain ripple factor and Efficiency.
Materials Required:
S No Item Range Specification Qty
1. Diode IN4007 2
2. Transformer 230V/(09)V 1
3. CRO 030 MHz 1
4. Resistor 1k 1
5. Bread board 1
6. Ammeter 0-50mA MC 1
7. Voltmeter 0-30V MC 1
8. Connecting wires Single stand As req.
9. Capacitor 22 F 1
Theory:
In FWR, current flows through the load in the same direction for both the half cycles
of the input voltage. This can be achieved with two diodes working alternatively. During the
positive half cycle diodes D1 and D2 conducts and supplies current to the load. During the
negative half cycle diodes D3 and D4 will conducts and current flows through the load in the
same direction. Hence the output obtained as the full wave rectifier DC voltage. The output
DC signal is the pulsating DC signal. By using the basic capacitive filter we can convert the
pulsating DC into pure DC signal.
When no filter circuit is present output voltage Vdc = 2Vm/.
The RMS value of the secondary voltage of the transformer is Vrms = Vm/2.
Formula Used:
Ripple Factor = [(Vrms/ Vdc)21]1/2.
-
7/28/2019 Edc Manual
19/47
Electronic Devices and Circuits EEE
19
Model Graph:
Input Wave Form:
Output Wave Form without Filter:
-
7/28/2019 Edc Manual
20/47
Electronic Devices and Circuits EEE
20
Output Wave Form with Filter:
Tabulation:
Without filter:
Vm Vrms Vdc Ripple factor Efficiency
With filter:
Vm Vrms Vdc Ripple factor Efficiency
-
7/28/2019 Edc Manual
21/47
Electronic Devices and Circuits EEE
21
Procedure:
1. The circuit connections are given as per the circuit diagram.2. The supply voltage is switched on.3. The DC voltage and current are noted down.4. By using the CRO observe the wave forms.5. From the tabulated reading find the ripple factor and percentage regulation.
Viva Questions:
1. What are the various types of filters used in rectifier circuit?2. What is surge current?3. How the surge current can be eliminated?4. State the expression for ripple factor.5. Explain the effect of load resistance and filter capacitance on the load voltage.
Result:
-
7/28/2019 Edc Manual
22/47
Electronic Devices and Circuits EEE
22
Pin Configuration for BC 547 NPN TRANSISTOR
Circuit Diagram:
-
7/28/2019 Edc Manual
23/47
Electronic Devices and Circuits EEE
23
Ex-No:
Date:
CHARACTERISTIC OF TRANSISTOR IN CE CONFIGURATION
Aim:
To study and plot the input and output characteristics of bipolar junction transistor in
common emitter configuration and determine its hybrid parameters.
Apparatus Required:
Formula Used:
Input Resistance, hie= Vbe/ Ib at constant Vce
Reverse transfer ratio, hre= Vbe/ Vce at constant Ib
Output Conductance, hoe= Ic/ Vce at constant Ib
Forward Current Transfer Ratio, hfe= Ic / Ibat constant Vce
Theory:
A bipolar (junction) transistor (BJT) is a type of transistor. It is a three-terminaldevice constructed ofdopedsemiconductormaterial and may be used in amplifying or
switching applications.
S. No Items Range Type Quantity
1 Transistor BC107 1
2 Regulated Power Supply (0-30V) Dual 1
3 Resistor 1K 2
4 Ammeter (0-50mA) MC 2
5 Voltmeter (0-3V) MC 1
6 Voltmeter (0-30V) MC 17 Bread Board 1
8 Connecting wires single strand AS req.
http://en.wikipedia.org/wiki/Transistorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Transistor -
7/28/2019 Edc Manual
24/47
Electronic Devices and Circuits EEE
24
Model Graph:
Input Characteristic: Output Characteristics:
Tabulation:
Input Characteristic:
Output Characteristics:
S. NoIb= Ib= Ib=
Vce(V)
Ic(mA)
Vce(V)
Ic(mA)
Vce(V)
Ic(mA)
S. NoVce= Vce= Vce=
Vbe(V)
Ib(mA)
Vbe(V)
Ib(mA)
Vbe(V)
Ib(mA)
-
7/28/2019 Edc Manual
25/47
Electronic Devices and Circuits EEE
25
Although a small part of the transistor current is due to the flow ofmajority carriers,most of the transistor current is due to the flow of minority carriers and so BJTs are
classified as minority-carrier devices.
Forward-active (or simply, active): The emitterbase junction is forward biased andthe basecollector junction is reverse biased. Most bipolar transistors are designed to
afford the greatest common-emitter current gain, F, in forward-active mode. If this is
the case, the collectoremitter current is approximately proportional to the base
current, but many times larger, for small base current variations.
Reverse-active (or inverse-active or inverted): By reversing the biasing conditions ofthe forward-active region, a bipolar transistor goes into reverse-active mode. In this
mode, the emitter and collector regions switch roles. Because most BJTs are designed
to maximize current gain in forward-
Active mode, the F in inverted mode is several (23 for the ordinary germaniumtransistor) times smaller. This transistor mode is seldom used, usually being
considered only for failsafe conditions and some types of bipolar logic. The reverse
bias breakdown voltage to the base may be an order of magnitude lower in this region.
Saturation Region: With both junctions forward-biased, a BJT is in saturation modeand facilitates high current conduction from the emitter to the collector. This mode
corresponds to a logical "on", or a closed switch.
Cutoff Region: In cutoff, biasing conditions opposite of saturation (both junctionsreverse biased) are present. There is very little current flow, which corresponds to a
logical "off", or an open switch.
Active Region: In active region, the emitter base junction is forward bias and thecollector base junction is reverse bias.
Common Emitter Configuration: The input is connected between base and emitterwhile output is connected between collector and emitter. Emitter is common to both
input and output circuit.
Input Characteristic: The curve drawn between base current, (Ib) and base-emittervoltage (Vbe) and base current Ib at constant collector-emitter voltage (Vce).
Output Characteristic: It is the curve drawn between collector current Ic andcollector-emitter voltage Vce for a constant base current Ib.
http://en.wikipedia.org/wiki/Majority_carrierhttp://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Majority_carrier -
7/28/2019 Edc Manual
26/47
Electronic Devices and Circuits EEE
26
-
7/28/2019 Edc Manual
27/47
Electronic Devices and Circuits EEE
27
Procedure:
Input Characteristic:
Connections are made as per the circuit diagram. Keeping the collector-emitter voltage (Vce) constant varies the emitter-base voltage
(Vbe) and note down the base current (Ib).
Repeat the step2 for varies values of constant Vce and tabulate the readings. Now plot the graph for the tabulated values.Output Characteristic:
Connections are made as per the circuit diagram. Keeping the base current (Ib) constant vary collector-emitter voltage (Vce) tabulate
collector current (Ic).
Repeat the step 2 for varies values of constant Ib and tabulate the readings. Now plot the graph for the tabulated values.
Viva Questions:
1. What is Transistor?2. Explain the working of NPN transistor?3. What is reverse saturation current?4. What is meant by emitter efficiency?5. Give the hparameters of CE configuration?6. Explain the input and output characteristics of CE configuration.
Result:
-
7/28/2019 Edc Manual
28/47
Electronic Devices and Circuits EEE
28
Pin Configuration for BC 547 NPN TRANSISTOR
Circuit Diagram:
-
7/28/2019 Edc Manual
29/47
Electronic Devices and Circuits EEE
29
Ex-No:
Date:
CHARACTERISTIC OF TRANSISTOR IN CB CONFIGURATION
Aim:
To study and plot the input and output characteristics of bipolar junction transistor in
common base configuration.
Apparatus Required:
Formula Used:
(1) Input impedance hib= Veb/ Ie, with Vcbconstant
(2) Output conductance hob = Ic/ Vcb, with Ie constant
(3) Forward current gain hfb = Ic/ Ie , with Vcbconstant
(4) Reverse Voltage gain hrb
= Veb
/ Vcb
, with Ieconstant
Theory:
A bipolar (junction) transistor (BJT) is a type of transistor. It is a three-terminaldevice constructed ofdoped semiconductormaterial and may be used in amplifying or
switching applications.
S. No Items Range Type Quantity
1 Transistor BC107 1
2 Regulated Power Supply (0-30V) Dual 1
3 Resistor 1K 2
4 Ammeter (0-50mA) MC 2
5 Voltmeter (0-30V) MC 2
6 Bread Board 1
7 Connecting wires single stand AS req.
http://en.wikipedia.org/wiki/Transistorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Transistor -
7/28/2019 Edc Manual
30/47
Electronic Devices and Circuits EEE
30
Model Graph:
Input Characteristics: Output Characteristics:
Tabulation:
Input Characteristic:
S. NoVcb= Vcb= Vcb=
Veb(V)
Ie(mA)
Veb(V)
Ie(mA)
Veb(V)
Ie(mA)
Output Characteristics:
S. NoIe = Ie = Ie =
Vcb(V)
Ic(mA)
Vcb(V)
Ic(mA)
Vcb(V)
Ic
(mA)
-
7/28/2019 Edc Manual
31/47
Electronic Devices and Circuits EEE
31
Although a small part of the transistor current is due to the flow ofmajority carriers,most of the transistor current is due to the flow of minority carriers and so BJTs are
classified as minority-carrier devices.
Forward-active (or simply, active): The emitterbase junction is forward biased andthe basecollector junction is reverse biased. Most bipolar transistors are designed to
afford the greatest common-emitter current gain, F, in forward-active mode. If this is
the case, the collectoremitter current is approximately proportional to the base
current, but many times larger, for small base current variations.
Reverse-active (or inverse-active or inverted): By reversing the biasing conditions ofthe forward-active region, a bipolar transistor goes into reverse-active mode. In this
mode, the emitter and collector regions switch roles. Because most BJTs are designed
to maximize current gain in forward-active mode, the F in inverted mode is several
(23 for the ordinary germanium transistor) times smaller. This transistor mode is
seldom used, usually being considered only for failsafe conditions and some types of
bipolar logic. The reverse bias breakdown voltage to the base may be an order of
magnitude lower in this region.
Saturation Region: With both junctions forward-biased, a BJT is in saturation modeand facilitates high current conduction from the emitter to the collector. This mode
corresponds to a logical "on", or a closed switch.
Cutoff Region: In cutoff, biasing conditions opposite of saturation (both junctionsreverse biased) are present. There is very little current flow, which corresponds to a
logical "off", or an open switch.
Common Base Configuration: The input is connected between base and emitterwhile output is connected between collector and base. Base is common to both input
and output circuit.
Input Characteristic: The curve drawn between base current, (Ib) and base-emittervoltage (Vbe) and base current Ib at constant collector-base voltage (Vcb).
Output Characteristic: It is the curve drawn between collector current Ic andcollector-emitter voltage (Vce) for a constant base current (Ie).
http://en.wikipedia.org/wiki/Majority_carrierhttp://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Majority_carrier -
7/28/2019 Edc Manual
32/47
Electronic Devices and Circuits EEE
32
-
7/28/2019 Edc Manual
33/47
Electronic Devices and Circuits EEE
33
Procedure:
Input Characteristic:
Connections are made as per the circuit diagram. Keeping the collector-base voltage (Vcb) constant varies the emitter-base voltage
(Vbe) and note down the emitter current (Ie).
Repeat the step2 for varies values of constant Vcband tabulate the readings. Now plot the graph for the tabulated values.Output Characteristic:
Connections are made as per the circuit diagram. Keeping the emitter current (Ie) constant varies collector-base voltage (Vcb) tabulate
collector current (Ic).
Repeat the step 2 for varies values of constant Ie and tabulate the readings. Now plot the graph for the tabulated values.
Viva Questions:
1. What is base width modulation?2. Explain Transfer Resistance.3. Explain the construction of PNP transistor.4. Give the hparameters of CB configuration?5. Explain the input and output characteristics of CB configuration.
Result:
-
7/28/2019 Edc Manual
34/47
Electronic Devices and Circuits EEE
34
Pin Configuration for BC 547 NPN TRANSISTOR
Circuit Diagram:
-
7/28/2019 Edc Manual
35/47
Electronic Devices and Circuits EEE
35
EX.No:
Date:
CHARACTERISTICS OF COMMON COLLECTOR CONFIGURATION
AIM:
To determine the characteristics of BJT under Common collector configuration.
Apparatus required:
S.No. Apparatus required Range Quantity
1. RPS (0-30)V 22. Voltmeter (0-1)V 2
3. Ammeter (0-100)A 2
4. Resistance 10K 1
5. Transistor BC 107 1
6. Bread board 1
7. Connecting wires As required
Theory:
A bipolar (junction) transistor (BJT) is a type of transistor. It is a three-terminaldevice constructed ofdoped semiconductormaterial and may be used in amplifying or
switching applications.
Although a small part of the transistor current is due to the flow ofmajority carriers,most of the transistor current is due to the flow of minority carriers and so BJTs are
classified as minority-carrier devices.
Forward-active (or simply, active): The emitterbase junction is forward biased andthe basecollector junction is reverse biased. Most bipolar transistors are designed to
afford the greatest common-emitter current gain, F, in forward-active mode. If this is
the case, the collectoremitter current is approximately proportional to the base
current, but many times larger, for small base current variations.
http://en.wikipedia.org/wiki/Transistorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Majority_carrierhttp://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Proportionality_%28mathematics%29http://en.wikipedia.org/wiki/Minority_carrierhttp://en.wikipedia.org/wiki/Majority_carrierhttp://en.wikipedia.org/wiki/Electronic_amplifierhttp://en.wikipedia.org/wiki/Semiconductorhttp://en.wikipedia.org/wiki/Doping_%28Semiconductors%29http://en.wikipedia.org/wiki/Transistor -
7/28/2019 Edc Manual
36/47
Electronic Devices and Circuits EEE
36
MODEL GRAPH FOR CC CONFIGURATION:
INPUT CHARACTERISTICS
OUTPUT CHARACTERISTICS
Tabulation :
Input Characteristics:
S. NoVce= Vce= Vce=
Vbc(V)
Ib(mA)
Vbc(V)
Ib(mA)
Vbc(V)
Ib(mA)
Output Characteristics:
S. NoIb = Ib= Ib=
Vce(V)
Ie(mA)
Vce(V)
Ie(mA)
Vce(V)
Ie(mA)
-
7/28/2019 Edc Manual
37/47
Electronic Devices and Circuits EEE
37
Reverse-active (or inverse-active or inverted): By reversing the biasing conditions ofthe forward-active region, a bipolar transistor goes into reverse-active mode. In this
mode, the emitter and collector regions switch roles. Because most BJTs are designed
to maximize current gain in forward-active mode, the F in inverted mode is several
(23 for the ordinary germanium transistor) times smaller. This transistor mode is
seldom used, usually being considered only for failsafe conditions and some types of
bipolar logic. The reverse bias breakdown voltage to the base may be an order of
magnitude lower in this region.
Saturation Region: With both junctions forward-biased, a BJT is in saturation modeand facilitates high current conduction from the emitter to the collector. This mode
corresponds to a logical "on", or a closed switch.
Cutoff Region: In cutoff, biasing conditions opposite of saturation (both junctionsreverse biased) are present. There is very little current flow, which corresponds to a
logical "off", or an open switch.
Common Collector Configuration: The input is connected between base andcollector while output is connected between collector and emitter. Collector is
common to both input and output circuit.
Input Characteristic: The curve drawn between base current, (Ib) and base-collectorvoltage (Vbc) at constant collector-emitter voltage (Vce).
Output Characteristic: It is the curve drawn between emitter current Ie andcollector-emitter voltage (Vce) for a constant base current (Ie).
-
7/28/2019 Edc Manual
38/47
Electronic Devices and Circuits EEE
38
-
7/28/2019 Edc Manual
39/47
Electronic Devices and Circuits EEE
39
PROCEDURE:
Input characteristics:
1. Keeping the voltage across collector to emitter (Vce) as constant, tabulate the
values of base current for various values of base collector voltage (Vbc).
2. Repeat the same procedure for various values of Vce.
Output characteristics:
1. Keeping the base current as constant, tabulate the values of emitter current (Ie)
for various values of collector emitter voltage (Vce).
2. Repeat the same procedure for various constant values of base current (Ib).
Result:
-
7/28/2019 Edc Manual
40/47
Electronic Devices and Circuits EEE
40
Circuit Diagram:
Model Graph:
Tabulation:
S. No Frequency(Hz) Current(mA)
-
7/28/2019 Edc Manual
41/47
Electronic Devices and Circuits EEE
41
Ex-No:
Date:
FREQUENCY RESPONSE OF SERIES AND PARALLEL RESONANCE
Aim:
To obtain the frequency response of parallel and series resonance circuits.
Apparatus Required:
S. No Items Range Type Quantity
1 Function Generator (0-30MHz) 1
2 Ammeter (0-5)mA MC 1
3 Resistor 1K 14 Capacitor 0.07F 1
5 Inductor 50 mH 1
6 Bread Board 1
7 Connecting Wires Single stand as req.
Statement:
Resonance is defined as a phenomenon in which the applied voltage and
resulting current are in phase with each other. In other words, an ac circuit is said to bein resonance it exhibits unity power factor condition, which means the applied voltage
and resulting current are in phase.
In ac RLC series circuit under the condition of resonance, the inductive reactance
gets cancelled with capacitive reactance and the impedance of a ac circuit consists only
resistance.
Resonance is series circuits are referred as series resonance or simply
resonance.
Characteristic of series resonance:
Input impedance is purely resistive. Applied voltage and current are in phase. Circuit current is maximum. Input impedance is equal to resistance. Power factor is unity Resonance frequency, Fr = 1/(2LC).
-
7/28/2019 Edc Manual
42/47
Electronic Devices and Circuits EEE
42
Circuit Diagram for Parallel Resonance:
Model Graph:
Tabulation:
S.No Frequency(Hz) Voltage(volts)
-
7/28/2019 Edc Manual
43/47
Electronic Devices and Circuits EEE
43
Parallel resonant circuit:
Similar to a series ac circuit there can be a resonance in parallel circuit. When the
power factor of a parallel ac circuit is unity, ie the voltage and total current are in phase
at particular frequency then the parallel circuit is said to be at resonance occurs is calledresonant.
Procedure:
Series circuit:
Connections are made as per the circuit diagram. Switch on the function generator and set the sinusoidal input voltage of
2v in function generator.
Set the function generator to a low frequency of 500 Hz. Note the current and tabulate the readings. Increase the frequency in steps upto 7 kHz. Repeat the step and draw the graph between frequency Vs current.
Parallel circuit:
Connections are made as per the circuit diagram. Switch on the function generator and set sinusoidal input voltage of in
function generator.
Set the function generator to a low frequency of 500 Hz. Note the voltage and tabulate the readings. Increase the frequency in steps upto 10 kHz. Repeat the step and draw the graph between frequency Vs voltage.
Result:
-
7/28/2019 Edc Manual
44/47
Electronic Devices and Circuits EEE
44
CIRCUIT DIAGRAM:
HIGH PASS FILTER:
LOW PASS FILTER:
-
7/28/2019 Edc Manual
45/47
Electronic Devices and Circuits EEE
45
Ex.No:
Date :
REALISATION OF PASSIVE FILTERS
AIM:
To determine experimentally the frequency response of low pass and high pass filters and
note down the cut-off frequency
Apparatus Required:
THEORY:
HIGH PASS FILTER:
This filter allows only high frequency of AC voltage and rejects the low frequency
components at the output. We know that Xc
-
7/28/2019 Edc Manual
46/47
Electronic Devices and Circuits EEE
46
TABULATION:
HIGH PASS FILTER LOW PASS FILTER
MODEL GRAPH:
Input voltage
in Volts
Frequency
in hz
Output
voltage
in volts
Gain=
20log(Vo/Vin)
In db
Input voltage
in Volts
Frequency
in hz
Output
voltage
in volts
Gain=
20log(Vo/Vin)
In db
-
7/28/2019 Edc Manual
47/47
Electronic Devices and Circuits EEE
Procedure:
1. The connections are made as per the Circuit diagram2. Switch on the power supply and increase the input frequency in steps of 100HZ and
note down the corresponding output voltage in the voltmeter
3. Calculate the gain value4. Draw the Graph between frequency Vs gain
Result:
HIGH PASS FILTER:
Designed cut-off frequency.Hz
obtained cut-off frequency.Hz
LOW PASS FILTER:
Designed cut-off frequency.Hz
obtained cut-off frequency.Hz