8/8/2019 Durafix Easyweld Flyer English

1/2

eldAluminium Welding, Brazing, and Soldering & Aluminium Repair3 IN 1 RODNow you can repair aluminium and zinc based parts such as this with out a welding machine.

. All you needisahandheld propanetype torch for smallpieces.

. Produtesasoundjoint that isstrongerthan the parentmetal.

. No flux is required.. Thereareno fumes.

. Low732F.working temperature. FEATURES:Iowcost. stronger than aluminium. noflux or fumes. Iowworking temperature

Aluminium Welding Instructions.. Clean area to be welded down to base.Brush the basewith stainlesssteel brush till shiny.Heat the areato beweldedl evenly.Asyou heat the basel rub the rod vigorously againstthe heated piece to be welded till rod flows.Neverapply heat directly to rod.

..

.ALWAYSWEARSAFETYGLASSES AND GLOVES

Do not useon magnesium.If you are unsure of the material, f ile off some metal and apply the torch. Magnesium like a flare.Duralux will not be held liable for any damages, injury or lossesdue to the misapplication of this product or any other reasonwhatsoever.NOW WELDING ALUMINUM ISAS EASYAS 1- 2 - 3HEAT RUB-IN

8/8/2019 Durafix Easyweld Flyer English

2/2

Vee the broken edges to about 45 degrees, cleanthe surface of any plating or scale back f rom edgesof the vee 1/8 of an inch.

Heat unt il it stars to flow. Turn flame parallel tosurface and with side of flame, hold at this heat.Heat welding rod to same temperature. Now withboth bases and welding rod at this temperature,touch rod to the break and rod will flow into vee,

thoroughly fusing the par ts.

Repeat operation until break is completely fil led. Besure to kick rod into weld to break down skinresistance as filler rod will lay on sur face and will

not fuse ifonly heat i sappl ied.

Brush surface to be repairedthoroughly under heat to break upsurface oxide.

Heat the joint hot enough for the rodto flow without the aid of the flame,thoroughly tinning the surface.

~~Wire brush thoroughly to break upsurface oxide and remove paint.

Heat. hot enough for the rod to flowwithout the aid of the flame. Tin theflat (not bevelled) side and attach atemporary support of carbon or

Durafix 3 in 1 RodThe most widely used rod on the market forWELDINGZINCBASEmetals - white - die cast-potmetal. Alloyed from pure virgin metals.Weldsmade with RODare clean and free fromslag. Produces a sound joint that isstrongerthan the parent metal. BRAZINGALUMINUMwithout the use offlux,sound and free from

porosity. SOLDERSGALVANIZEDalso used as aRUB-ONsolder. Use a slightly carburizing flame(excess of acetylene), with small tip for mostwork. MELTINGPOINT7320F.Durafix is used to: repair Kirksite dies, powertools, aluminium radiators, power mowercasting, propellers, lower units and boat hulls.

THOUSANDS OF OTHERUSES.

Brush Tinned surface under heat,thorougly fil ling the open pores.

Turn and tin bevelled side, building outthe blade slightly large than its originalsize.Grind damaged edges to a 45bevel. Pitch propeller to standards.

With sides thoroughly tinned, f low inenough rod to fil l the Vee.Besurefil ler fuses with the tinned surfacewithout melting the base metal.

Let cool, then grind properstandards. Results?...a well preparedwheel wi thout porosity for you tobalance and paint!

SpecificationsTensile Strength,lbs/sq. in 47,000Compression Strength,lbs/sq. in 60,000-75,00Shear Strength, Ibs/sq. in 34,OOOCharpy Impact Str,lbs/sq. in 4ft/lb to break 1/4"barHardness (Srinel!) 100DictilityGood GoodMelting Point """"""""""""""""""""""""""""""""""'" 732FSpecificGravity 6.7Density (lbs/cu. in.) 0.25Elongation (in 2") " 30/0Coefficient of LinearExpansion 15.4xl0-6/oFElectricalConductivity 24.9% of CuThermal Conductivity 0.24 cal/cu. cm/QC