William H. Graff, American TCB
Updates for Test Reporting
GSM Duty Factor
Test Report and supporting documentation should clearly support GPRS capabilities of the device. Please include information regarding both the GPRS classes (e.g. class 10 and class A).
Test with maximum power for both body-worn and head positions as applicable.
Currently the FCC has been asking on most GSM applications to verify if the GPRS capability will work while the device is transmitting in voice mode.
CDMA 2000 / W-CDMA
The FCC has requested all TCBs to consult with them before any attempt to approve CDMA 2000 is attempted.
FCC is considering whether or not to consider CDMA 2000 a “new technology” and therefore subject to approval exclusively by the Commission
Layards
Devices with Neck worn lanyards or that are intended to be next to the body should be tested with 0 gap and body tissue liquid. Both Front and Back should be tested.
An eyelet on the device does not necessitate use of neck lanyards. Instructions to the user should clearly support the correct uses.
Layards
An eyelet on the device does not necessitate use of neck lanyards. Instructions to the user should clearly support the correct uses and accessories provided.
If the manufacturer provides a neck lanyard with the device (in the box), or suggests to the user that this device is intended for lanyards, then it should be tested with 0cm gap.
Tablet Devices
Tablet device screen sizes range 8-14” and weights range 2-8 lbs.
Tablet Type Devices
Smaller devices may qualify for handheld-only operations, but filing must include strong justification for such – contact TCB or FCC for guidance if needed.
Generally unless a strong justification can be made, portable may be assumed.
Tablet Type Devices
Consumer tablet PCs are expected to have lap-held use positions per [IDB RFx 7) d) ii)]*.
* - Excert from Mobile and Portable Device RF Exposure Equipment Authorization Procedures Released March 18, 2004 which states:
For undefined or unclear device usage positions, where existing or standardized test procedures are not applicable, SAR should be evaluated according to the normal operating configurations which are intended for the device.
SAR Test Documentation
Important test setup details affecting SAR should be provided in SAR Test Documentation:
Belt clip and air gap thickness.
SAR Test Documentation
• PCMCIA card distance to phantom for laptop and PDA testing.
P1528 device reference lines
for held to ear testing.
USB Style Dongles
• “Direct-connected” USB (without integral cable) differs from most PCMCIA in that port alignment may be horizontal (H), vertical (V), and 180 degrees H or V, with respect to a notebook computer host
USB Style Dongles
• Grantee is responsible for SAR compliance in all
such intended use positions.• 1-host SAR testing is accepted for many Part 15
and some licensed-service USB-dongle transmitters.
• 3-host SAR test results have been filed for some licensed-service devices
• IDB/KDB Mar04 webpost RFx Procedures 7)b), 7)c) are applicable
802.11 WLAN Devices
The FCC has spent considerable amount of time reviewing these devices and experimenting with many aspects of the SAR testing. The FCC has been seriously thinking about proposing many changes to the SAR procedures used for testing for these types of devices.
Remember that these are proposals, are subject to change, and may or may not be implemented.
802.11 WLAN Devices
Proposed Changes Include the following. Note that these are proposed changes and should not be considered final until formally released by the FCC:
1. Default channels use for test may be different than simply Low, Mid and High and will depend on power measurements of channels near the Low and High channels. This is due to the variance of bandedge channels seed in some devices where the bandedge channels have reduced power.
Proposed F
uture G
uidelines Only
802.11 WLAN Devices
2.) Certain modulations may be considered required for default testing, but others may still need to be required depending on certain set power levels.
For example, 802.11g is only required to be tested if the average power is 0.25 dB > than the 802.11b power for the same channel
Proposed F
uture G
uidelines Only
802.11 WLAN Devices
3.) Higher data rates usually have lower average output. Higher data rates should be tested only when the average output is 0.25 dB > that at the lowest data rate for the default “a-b/g mode” test channels
Proposed F
uture G
uidelines Only
802.11 WLAN Devices
4.) Turbo modes (proprietary modes) typically operate at higher data rates requiring higher order modulations & lower average power. Turbo, half & quarter rate channels should be tested at the lowest data rate used in each proprietary mode when the average output is greater than that on the closest default “a-b/g mode” channels.
Proposed F
uture G
uidelines Only
802.11 WLAN Devices
5.) Switched Diversity Issue.
The SAR of each antenna should be measured independently on the highest output channel in each “a-b/g mode”.
Other channels should be tested only when the SAR vary by > 25% for the two antennas on highest output channel or > 1.2 W/kg.
Proposed F
uture G
uidelines Only
802.11 WLAN Devices
6.) MIMO Type Devices.
FCC is developing Procedures. These are likely to involve simultaneous TX conditions and
Proposed F
uture G
uidelines Only
5 GHz SAR
The FCC has expressed that review of SAR for devices in the 3 – 6 GHz range will hopefully be released to TCB’s soon. However exact dates have not been released.
PCMCIA Cards
For PCMCIA Cards with antennas external to
the host device, the FCC is considering possible changes to their current testing requirements.
1) The 3 host policy that is typically required in certain situations may change for depending on certain acceptable margins to ensure compliance for variations among typical laptops.
Proposed F
uture G
uidelines Only
PCMCIA Cards
2) The FCC is also considering test methods
with use an extender card instead of a typical laptop computers and compare these measurements to those made in a typical host.
Proposed F
uture G
uidelines Only
Proposed Changes
The FCC also expects that any new procedures required for SAR measurements will likely also have a transition period associated with them. This is subject to be determined depending on the future release of information from the FCC.
FCC/TCB Training Bulletins
HAC for cellphones is mandatory on for 25% of a carrier’s product line
HAC test procedure already exists.
TCBs are able to review HAC soon.
FCC/TCB Training Bulletins
5GHz SAR not yet released to TCBs.
Notice will come in the form of a R&O
Training material is in preperation
FCC/TCB Training bulletins
SAR testing for WiFi products is being further refined.
More emphasis on test software used inside WiFi transmitter and defining it’s characteristics.
FCC will require more documentation of software, especially on/off transmitter timing characteristics.
FCC/TCB Training Bulletins
No agreement yet on DFS testing for 802.11a. Testing with NTIA / FCC on proposed new procedure has been scheduled for November.
FCC hopes to get revised DFS Test Procedure to TCBs before end of year.
FCC/TCB Training Bulletins
Field Programmability to add DFS to existing 802.11a radios prohibited unless radio is Certified as a SDR.
Factory programmability allowed using the Class II change procedure.
FCC/TCB Training Bulletins
DFS products must go to FCC
SDR products must go to FCC
***A DFS testing exclusion exists for client equipment which is under the control of a Certified access point.
***Ad-Hoc mode for clients prohibited
FCC/TCB Training Bulletins
FCC has provided further guidance on MIMO and steered array antennas.
Specific guidance is offered from FCC on Pout measurements, RF Exposure calculations, radiated Restricted Band measurements.
FCC/TCB Training Bulletins
FCC will now allow Class II changes for RF category “Portable” to “Mobile” to be handled by TCBs.
FCC/TCB Training Bulletins
GPS repeaters are not permitted in USA. GPS spectrum is carefully protected. No Part 15 Intentional Radiators are permitted.
Reference: See 15.205