Product Specifications OUTDOOR UNIT
POWER CONNS. — V/PH/HZ MIN. BRCH. CIR. AMPACITY BR. CIR. PROT. RTG. - MAX. (AMPS)
COMPRESSOR NO. USED - NO. SPEEDS VOLTS/PH/HZ R.L. AMPS - L.R. AMPS FACTORY INSTALLEDSTART COMPONENTS INSULATION/SOUND BLANKE TCOMPRESSOR HEAT
OUTDOOR FAN DIA. (IN.) - NO. USED TYPE DRIVE - NO. SPEEDS CFM @ 0.0 IN. W.G. NO. MOTORS - HP MOTOR SPEED R.P.M. VOLTS/PH/HZ F.L. AMPS
OUTDOOR COIL — TYPE ROWS - F.P.I. FACE AREA (SQ. FT.) REFRIGERANT
CONTROL
REFRIGERANT
LBS.
—
R-410
(O.D.
UNIT)
FACTORY
SUPPLIED
LINE
SIZE
- IN.
O.D.
GAS
LINE
SIZE
- IN.
O.D.
LIQ.
CHARGING
SPECIFICATION
DIMENSIONS
CRATED
(IN.)
WEIGHT
SHIPPING
(LBS.)
NET
(LBS.)
J4AC6060A1000AA
TAG:
_________________________________
5.0 Ton Split SystemAir Conditioner - 1 Phase J4AC6060A1000AA
S UBMITTAL
J4AC6060A1000AA208/230/1/60
29.950
SCROLL1 - 1
208/230/1/6021.8-127.1
NOPROPELLER23-5/8 - 1DIRECT-1
35501 - 1/31050
208/230/1/602.60
MICROCHANNEL1 - 2318.4
ORIFICE
6 LBS.
- 14 OZ.
YES7/83/8
W
X
H
X D30-1/5x38-63/64x30-1/5
225192
NONO
J4AC6060A1000AA
Model H W L LIQUID VALVE SIZE GAS VALVE SIZE
843 (33-3/16) 740 (29-1/8) 3/8 7/8
NOTE: All dimensions are in mm/inches.
740 (29-1/8)
SUCTION LINE CONNECTION
CONTROL WIRING 7/8” (22.2mm)
KNOCKOUT 1-11/32” (34.5mm)
LIQUID LINE CONNECTION
SERVICE FITTING
SERVICE FITTING
POWER WIRING SEE DETAIL A
DETAIL A
HOLE 1-3/32” (27.8mm)
NOTE: GRILL APPEARANCE MAY VARY.
SERVICE ACCESS ALLOW 24” CLEARANCE
AIR INLETS LOUVERED PANELS ALLOW 12” MINIMUM CLEARANCE
W
ACCESS VALVLEFOR LOW PRESSURENOTE: ONLY ADOPTED BY HEAT PUMP, CAN BE USED FOR MEASURING PRESSURE AFTER SWITCHOVER VALVE-SUCTION TO COMPRESSOR ORREFRIGERANT CHARGE.
See Table
ModeCooling
Liquid Pressrue at Small Service Value(psig)
F )oOutdoor Ambient Temperature(
16 SEER R410A AC Charge Chart 5 TON
426402378355331310288266246105428404380357333311289268248109431407382358334312290269250113433409384360335313291271252117435411386361336314292272253121438413388363338316294274255125440415390365340318296276257129443418392367342320298278259133446419393369344322300279260137448421395371346324302281262141450423397373348326304283264145451424398374350328306285266149453426400377353331308287267153455428401379356334311289269157457430403381358336314292271161458431404383361339317294273165
10510095908580757065
no crankcase heater is used. heat is used or five (5) minutes ifmust be checked and unit powered for one (1) hour if
crank case 4) The unit electrical installation
Installation must be complete with brazed joints and drier visually inspected.F.
3)°F to 100°
F. 2) Indoor temperature between 70
°65
conditions must be met:
1) Outdoor temperature above
In order to properly charge the system the following
Leave bottle closed until ready to charge Manual Charge Hookup
has been evacuated, add the total calculated charge.new system Installation. if the entire systemWith an accurate scale (+/- 1 oz.) adjust charge difference between that shown on the unit data plate and that calculated for the
1.2 oz. per foot±” .6 oz. per foot 1/2±” 3/8 .4 oz. per foot±” .2 oz. per foot 5/16±” 1/4
15 ft add the charge as indicated below:unit is sufficient for 15 feet of standard size interconnecting liquid line. For tube lengths over
otherwise, evacuate the entire system. The factory refrigerant charge in the outdoorFor a new installation, evacuation of interconnecting tubing and indoor coil is adequate;CHARGING BY WEIGHT
valves.PRESSURE changes, go back to step 2
otherwise remove test equipment and cover therecover charge to lower it. 6. After running unit for 10 minutes if the SUCTION LINE
PRESSURE to the TARGET LIQUID PRESSURE, add charge to raise the pressure or rows and columns. 5. Compare the measured LIQUID LINE
LINE PRESSURE falls between rows or columns then estimate the TARGET LIQUID PRESSURE between the or SUCTION PRESSURE and the OUTDOOR AMBIENT TEMPERATURE, if falls between rows or columns then estimate the TARGET LIQUID PRESSURE
PRESSURE. 4. Find the TARGET LIQUID PRESSURE at the intersection between the SUCTION LINE AMBIENT TEMPERATURE within 6 inches of coil.
3. Measure SUCTION LINEFollow these steps: 1. Run in cooling mode at least 10 minutes. 2. Measure OUTDOORCHARGING BY LIQUID PRESSURE
THIS SYSTEM MUST NOT BE CHARGED BY SUBCOOLING.THIS IS A CHARGING PROCEDURE TO PREVENT OVERCHARGING.
REFRIGERANT CHARGING CHART
Literature Order Numbe r SS-PRC007-EN
File Numbe r —
Supersede s SS-PRC007-EN 2/0 2
Stocking Locatio n PI Louisville & Webb/Mason Houston
has a policy of continuous product and product data improvement and it reserves the right to change design and specifications without notice.
MechanicalSpecification Options
General
Casing
Refrigerant Controls
Scroll Compressor
Condenser Coil
Optional accessories
Liquid line drier
—
The J4AC60 is fully charged from the factory. This unit is designed to operateat outdoor ambient temperatures as high as 115°F. Cooling capacities are matched with air handlers and furnace coils that are AHRI certified. The unit is certified to ETL. Exterior is designed for outdoor application.
Unit casing is constructed of heavy gauge, Galvanized steel and painted with a weather-resistant powder paint on all grilles, panels, pre-paint on all other panels. And had 500-hours salt spray tested.
Refrigeration system controls include condenserfan, compressor contactor.
Features include low vibration and noise.
The outdoor coil provides low airflow resistance and efficient heat transfer. The coil is protected on all four sides by grille panels.
It is used to filter out impurities and water in the system, ensures system clean and dry.
OXBOX