Download - TL- WR340G user manual.pdf

TL-WR340G/TL-WR340GD User Guide 54M Wireless Router

Rev: 1.0.2

1910010064

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark

of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

TECHNOLOGIES CO., LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO., LTD.

All rights reserved.

II

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. • Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause

undesired operation.

FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

III

National Restrictions 2400.0-2483.5 MHz

Country Restriction Reason/remark

Bulgaria General authorization required for outdoor use and

public service

France

Outdoor use limited to 10

mW e.i.r.p. within the band

2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band

has been ongoing in recent years to allow current relaxed

regulation. Full implementation planned 2012

Italy If used outside of own premises, general authorization is

required

Luxembourg None General authorization required for network and service

supply(not for spectrum)

Norway Implemented This subsection does not apply for the geographical area

within a radius of 20 km from the centre of Ny-Ålesund

Russian

Federation

Only for indoor applications

Note：It’s not used outdoors in France.

IV

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 54M Wireless Router

Model No.: TL-WR340G

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC

The above product is in conformity with the following standards or other normative documents: ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.6.1:2005 ETSI EN 301 489-17 V1.2.1:2002 EN 61000-3-2:2006 EN 61000-3-3:1995+A1:2001 EN60950-1:2006 EN50371:2002


The above product is in conformity with the following standards or other normative documents EN 55022:2006 EN 55024:1998+A1:2001+A2:2003 EN 61000-3-2:2006 EN 61000-3-3:1995+A1:2001+A2:2005


The above product is in conformity with the following standards or other normative documents EN60950-1:2006

Person is responsible for marking this declaration:

Zhao Jianjun Director of International Business

TP-LINK TECHNOLOGIES CO., LTD. South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,

Shenzhen, P. R. China

Package contents

The following contents should be found in your box:

One TL-WR340G/TL-WR340GD 54Mbps Wireless Router

One AC power Adapter for TL-WR340G/TL-WR340GD 54Mbps Wireless Router

Quick Installation Guide

One Resource CD for TL-WR340G/TL-WR340GD 54Mbps Wireless Router, including:

• This Guide

• Other Helpful Information

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.

Conventions

The Router or TL-WR340G/TL-WR340GD, or device mentioned in this User guide stands for

TD-WR340G/TL-WR340GD 54M Wireless Router without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may

differ from the actual situation.

You can set the parameters according to your demand.

Note: The two devices of TL-WR340G and TL-WR340GD are shared with this User Guide, we use TL-WR340G for example.

The differences between them are:

TL-WR340G router with an fixed antenna;

TL-WR340GD router with a detachable antenna.

II

CONTENTS

Chapter 1. Introduction ........................................................................................ 1

1.1 Product Overview...................................................................................................... 1

1.2 Main Features ........................................................................................................... 1

Chapter 2. Hardware Installation ......................................................................... 3

2.1 The Front Panel ........................................................................................................ 3

2.2 The Back Panel ......................................................................................................... 4

2.3 System Requirements ............................................................................................... 4

2.4 Installation Environment Requirements..................................................................... 5

2.5 Connecting the Device .............................................................................................. 5

2.6 Configure PC............................................................................................................. 6

Chapter 3. Software Configuration.................................................................... 10

3.1 Login ....................................................................................................................... 10

3.2 Status ...................................................................................................................... 10

3.3 Quick Setup............................................................................................................. 11

3.4 Network ................................................................................................................... 12

3.4.1 LAN.................................................................................................................................12 3.4.2 WAN ...............................................................................................................................12 3.4.3 MAC Clone .....................................................................................................................23

3.5 Wireless .................................................................................................................. 24

3.5.1 Wireless Settings............................................................................................................24 3.5.2 MAC Filtering..................................................................................................................28 3.5.3 Wireless Statistics ..........................................................................................................30

3.6 DHCP ...................................................................................................................... 31

3.6.1 DHCP Settings ...............................................................................................................31 3.6.2 DHCP Clients List...........................................................................................................32 3.6.3 Address Reservation ......................................................................................................33

3.7 Forwarding .............................................................................................................. 34

3.7.1 Virtual Servers................................................................................................................34 3.7.2 Port Triggering................................................................................................................35 3.7.3 DMZ................................................................................................................................37 3.7.4 UPnP ..............................................................................................................................38

3.8 Security ................................................................................................................... 39

3.8.1 Firewall ...........................................................................................................................39 3.8.2 IP Address Filtering ........................................................................................................40

III

3.8.3 Domain Filtering .............................................................................................................41 3.8.4 MAC Filtering..................................................................................................................43 3.8.5 Remote Management.....................................................................................................44 3.8.6 Advanced Security .........................................................................................................45

3.9 IP & MAC Binding Setting ....................................................................................... 47

3.9.1 Binding Setting ...............................................................................................................47 3.9.2 ARP List..........................................................................................................................49

3.10 Routing.................................................................................................................... 49

3.11 DDNS ...................................................................................................................... 51

3.11.1 Dyndns.org DDNS..........................................................................................................51 3.11.2 Oray.net DDNS ..............................................................................................................51 3.11.3 Comexe.cn DDNS..........................................................................................................52

3.12 System Tools .......................................................................................................... 53

3.12.1 Time................................................................................................................................54 3.12.2 Firmware.........................................................................................................................55 3.12.3 Factory Defaults .............................................................................................................55 3.12.4 Backup and Restore.......................................................................................................56 3.12.5 Reboot ............................................................................................................................56 3.12.6 Password........................................................................................................................57 3.12.7 Log..................................................................................................................................58 3.12.8 Statistics .........................................................................................................................58

Appendix A: Glossary............................................................................................ 60

Appendix B: Specifications ................................................................................... 61

Appendix C: FAQ.................................................................................................... 62

IV

TL-WR340G/TL-WR340GD 54M Wireless Router User Guide

1

Chapter 1. Introduction Thank you for choosing the TL-WR340G/TL-WR340GD 54Mbps Wireless Router.

1.1 Product Overview

Thank you for choosing the TL-WR340G/TL-WR340GD 54Mbps Wireless Router. This router

provides dedicated solution for Small Office/Home Office (SOHO) networks. With your network all

connected, your local wired or wireless network can share Internet access, files and fun for

multiple PCs through one ISP account. In addition, this device supports Bridge mode which can

make two APs communicate with each other wirelessly.

It is an easy Web-based setup for installation and management. Even though you may not be

familiar with the router, this guide will make configuring the router easy. Before installing the

router, please look through this guide to know all the router’s functions.

1.2 Main Features

Complies with IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u standards.

1 10/100M Auto-Negotiation RJ45 WAN port, 4 10/100M Auto-Negotiation RJ45 LAN ports,

supporting Auto MDI/MDIX.

Shares data and Internet access for users, supporting PPPoE, Dynamic IP, Static IP, L2TP,

PPTP, BigPond Cable Internet access.

Ignores Ping packets from WAN or LAN ports.

Connecting Internet on demand and disconnecting from the Internet when idle for PPPoE.

Built-in NAT and DHCP server supporting static IP address distributing.

Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC address

filtering.

Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.

Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control

List).

Supports Flow Statistics.

Supports firmware upgrade.

Supports Web management.

Supports Virtual Server, Special Application and DMZ host.

Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through.

Supports ICMP-FLOOD, UDP-FLOOD, and TCP-SYN-FLOOD filter.

Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps data transfer rates.


2

Supports connecting/disconnecting from the Internet on a specified time of day.

Supports access control, parents and network administrators can establish restricted access

policies based on time of day for children or staff.


Chapter 2. Hardware Installation

2.1 The Front Panel

Figure 2-1

The Router’s LEDs are located on the front panel (View from left to right).

LED Explanation:

Name Status Indication

Off No Power PWR

On Power on

Off The Router has an error

On The Router is initializing SYS

Flashing The Router is working properly

Off The Wireless function is disabled WLAN

Flashing The Wireless function is enabled

Off There is no device linked to the corresponding port

On There are devices linked to the corresponding ports but no data

transmitted or received. WAN/1-4 (LAN)

Flashing Sending or receiving data over corresponding port

3


4

2.2 The Back Panel

Figure 2-2

The following parts are located on the rear panel (View from left to right).

Antenna: Used for wireless operation and data transmit.

Reset Button: There are two ways to reset the Router's factory defaults. With the router

powered on, use a pin to press and hold the Reset button until the SYS LED becomes

quick-flash from slow-flash (about 5 seconds), and then release the button and wait the router

to reboot to its factory default settings, or restore the default setting from “Management -

Settings - Restore Default “of the Router's Web-based Utility.

WAN: RJ45 WAN port for connecting the router to a cable/DSL Modem, or Ethernet.

1, 2, 3, 4 (LAN): Through these ports, you can connect the Router to your PCs and the other

Ethernet network devices.

Power: The Power plug is where you will connect the power adapter.

2.3 System Requirements

Broadband Internet Access Service (DSL/Cable/Ethernet)

One DSL/Cable Modem that has an RJ45 connector (you do not need it if you connect the router to the Ethernet)


5

Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45 connectors

TCP/IP protocol must be installed on each PC

Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later

2.4 Installation Environment Requirements

The Product should not be located where it will be exposed to moisture or excessive heat.

Place the Router in a location where it can be connected to the various devices as well as to

a power source.

Make sure the cables and power cord are placed safely out of the way so they do not create a

tripping hazard.

Designed to go up to 100 meters indoors and up to 300 meters outdoors for wireless

connection.

The Router can be placed on a shelf or desktop.

2.5 Connecting the Device

Before installing the Router, please make sure your broadband service provided by your ISP is

available. If there is any problem, please contact with your ISP. After that, please install the

Router according to the following steps. Don't forget to pull out the power plug and keep your

hands dry.

1. Locate an optimum location for the Router. The best place is usually near the center of the area in which your PC will be wirelessly connected. The place had better accord with the Installation Environment Requirements.

2. Adjust the direction of the antenna. Normally, upright is a good direction.

3. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the router, shown

in Figure 2-3. (If you have the wireless NIC and want to use wireless function, you can skip

this step.)

4. Connect the DSL/Cable Modem to the WAN port on the router, shown in Figure 2-3.

5. Connect the AC power adapter to the AC power socket on the router, and the other end into

an electrical outlet. The router will start to work automatically.

6. Power on your PC and Cable/DSL Modem.


6

Figure 2-3 Hardware Installation of the Router

2.6 Configure PC

Your PC needs a network adapter. You may directly connect your adapter to the Router, or you

may connect your adapter to a Hub/Switch, and then connect the Hub/Switch to the Router.

Follow the instructions below to configure a computer running Windows XP to be a DHCP client.

1. From the Start menu on your desktop, go to Settings, and then click on Network Connections.


7

Figure 2-4

2. In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties.

Figure 2-5

3. In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet Protocol (TCP/IP) under “This connection uses the following items:” by clicking on it once.


8

Click on the Properties button.

Figure 2-6

4. Select “Obtain an IP address automatically” by clicking the radio-button. Click OK

Figure 2-7

Configure the IP address manually

1. Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.*

(* is any value between 2 to 254, Subnet mask is 255.255.255.0, Gateway is 192.168.1.1,

DNS address is the value provided by ISP).


9

Now, you can run the Ping command in the command prompt to verify the network

connection between your PC and the Router. The following example is in Windows XP

Operating System.

2. Open a command prompt, From the Start menu on your desktop, select run tab, type

cmd in the field, and type ping 192.168.1.1 on the screen that appears, and then press

Enter.

If the result displayed is similar to that shown in Figure below, the connection between your PC

and the Router has been established.

Figure 2-8

If the result displayed is similar to that shown in figure below, it means that your PC has not

connected to the Router.

Figure 2-9

Please check it following these steps:

Note: If the connection between your PC and the Router is correct?

The LEDs of LAN port which you link to on the devicer and LEDs on your PC's adapter should be lit.

If the TCP/IP configuration for your PC is correct?

If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1.


10

Chapter 3. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation, For

advanced users, if you want to know more about this device and make use of its functions

adequately, you need to read this chapter and configure advanced settings though the

Web-based Utility.

3.1 Login

After your successful login, you can configure and manage the device. There are main menus on

the left of the web-based utility. Submenus will be available after you click one of the main menus.

On the right of the web-based utility, there are the detailed explanations and instructions for the

corresponding page. To apply any settings you have altered on the page, please click the Save button.

3.2 Status

The Status page displays the router's current status and configuration. All information is

read-only.

LAN This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask.

Wireless This field displays basic information or status for wireless function, including Wireless Radio, SSID, Channel, Mode, Wireless MAC address, and IP address.

WAN These parameters apply to the WAN port of the router, including MAC address, IP address, Subnet Mask, Default Gateway, DNS server and WAN connection type. If PPPoE is chosen

as the WAN connection type, the Disconnect button will be shown here while you are accessing

the Internet. You can also cut the connection by clicking the button. If you have not connected to

the Internet, just click Connect to establish the connection.

Traffic Statistics This field displays the router's traffic statistics.

System Up Time The total up time of the router from when it was switched on or reset.


11

Figure 3-1 Router Status

3.3 Quick Setup

Please refer to Quick Installation Guide


12

3.4 Network

Figure 3-2 the Network menu

There are three submenus under the Network menu (shown in Figure 3-2): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. The

detailed explanations for each submenu are provided below.

3.4.1 LAN

You can configure the IP parameters of LAN on this page.

Figure 3-3 LAN

MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.

IP Address - Enter the IP address of your router in dotted-decimal notation (factory default: 192.168.1.1).

Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask.

Note: If you change the IP Address of LAN, you must use the new IP Address to login the router.

If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will not take effect, until they are re-configured.

If the new LAN IP Address you set is not in the same subnet, the Virtual Server and DMZ Host will change accordingly at the same time.

3.4.2 WAN

You can configure the WAN port parameters on this page.

First, please choose the WAN Connection Type (Dynamic IP/Static IP/PPPoE/802.1X + Dynamic

IP/802.1X + Static IP/Big Pond Cable/L2TP/PPTP) for Internet. The default type is Dynamic IP. If

you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and

a password, please select the type of your ISP provided (PPPoE/BigPond/L2TP/PPTP). If you


13

are not sure which connection type you use currently, please contact your ISP to obtain the

correct information.

1. If you choose Dynamic IP, the router will automatically get IP parameters from your ISP.

You can see the page as follows (Figure 3-4):

Figure 3-4 WAN – Dynamic IP

This page displays the WAN IP parameters assigned dynamically by your ISP, including IP

address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP

parameters from your ISP. Click the Release button to release the IP parameters.

MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks

is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and

should not be done unless you are sure it is necessary for your ISP connection.

If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter

the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will

be assigned dynamically from your ISP.

Note: If you get address and find error when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.

Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast

applications. If you cannot get the IP Address normally, you can choose this option. (This is

rarely required.)


14

2. If you choose Static IP, you should have fixed IP Parameters specified by your ISP. The

Static IP settings page will appear, shown in Figure 3-5:

Figure 3-5 WAN - Static IP

You should type the following parameters into the spaces provided:

IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.

Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.

Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP.

MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet

networks is 1500 Bytes. For some ISPs you may need to modify the MTU. But this is rarely

required, and should not be done unless you are sure it is necessary for your ISP

connection.

Primary DNS - (Optional) Enter the DNS address in dotted-decimal notation provided by your ISP.

Secondary DNS - (Optional) Type another DNS address in dotted-decimal notation provided by your ISP if provided.

3. If you choose PPPoE, you should enter the following parameters (Figure 3-6):


15

Figure 3-6 WAN - PPPoE

User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.

Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. Caution: Sometimes the connection cannot be disconnected although you specify a time to

Max Idle Time, since some applications is visiting the Internet continually in the background.

Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button.

Time-based Connecting - You can configure the router to make it connect or disconnect based on time. Enter the start time in HH:MM format for connecting and end time in HH:MM format for disconnecting in the Period of Time fields.

Note: Only when you have configured the system time on System Tools -> Time page, will the Time-based Connecting function can take effect.

Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect from the Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number time in minutes that you wish to have the Internet connecting last unless a new link is requested.


16

Caution:Sometimes the connection cannot be disconnected although you specify a time to

Max Idle Time, since some applications are visiting the Internet continually in the background.

Click the Connect button to connect immediately. Click the Disconnect button to disconnect

immediately.

Click the Advanced Settings button to set up the advanced option, the page shown in Figure

3-7 will then appear:

Figure 3-7 PPPoE Advanced Settings

Packet MTU - The default MTU size is 1480 bytes, which value is usually fine. For some ISPs, you need modify the MTU. This should not be done unless you are sure it is necessary for your ISP.

Service Name/AC Name - The service name and AC (Access Concentrator) name, these should not be configured unless you are sure it is necessary for your ISP.

ISP Specified IP Address - If you know that your ISP does not automatically transmit your IP address to the router during login, click “Use the IP Address specified by ISP” check box and enter the IP Address in dotted-decimal notation, which your ISP provided.

Detect Online Interval - The default value is 0, you can input the value between 0 and 120. The router will detect Access Concentrator online at every interval between seconds. If the value is 0, it means, do not detect.

DNS IP address - If you know that your ISP does not automatically transmit DNS addresses to the router during login, click “Use the following DNS servers” checkbox and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well.

Click the Save button to save your settings.

4. If you choose 802.1X + Dynamic IP, you should enter the follow parameters(Figure 3-8) :


17

Figure 3-8 802.1X + Dynamic IP Settings

User Name - Enter the user name for 802.1X authentication provided by your ISP

Password - Enter the password for 802.1X authentication provided by your ISP.

Click Login to start 802.1X authentication.

Click Logout to end 802.1X authentication.

Host Name - This field is required to be filled by some service provider.

5. If you choose 802.1X + Static IP, you should enter the follow parameters(Figure 3-9) :


18

Figure 3-9 802.1X + Static IP Settings

User Name - Enter the user name for 802.1X authentication provided by your ISP Password - Enter the password for 802.1X authentication provided by your ISP.

Click Login to start 802.1X authentication.

Click Logout to end 802.1X authentication.

IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP. Default Gateway - (Optional) Enter the default gateway IP address in dotted-decimal

notation provided by your ISP.

6. If you choose Big Pond Cable, you should enter the following parameters (Figure 3-10):


19

Figure 3-10 Big Pond Settings


Auth Server - Enter the authenticating server IP address or host name. Auth Domain - Type in the domain suffix server name based on your location. Eg,

NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.au

Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. Caution: Sometimes the connection cannot be disconnected although you specify a time to

Max Idle Time, since some applications are visiting the Internet continually in the

background.


Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as


20

soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested.

Caution: Sometimes the connection cannot be disconnected although you specify a time to



immediately.

7. If you choose L2TP, you should enter the following parameters (Figure 3-11):

Figure 3-11 L2TP Settings


Dynamic IP/ Static IP – Choose either as you are given by your ISP.


immediately.

Connect on Demand - You can configure the router to disconnect from your Internet


21

connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. Caution: Sometimes the connection cannot be disconnected although you specify a time to



Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested.



8. If you choose PPTP, you should enter the following parameters (Figure 3-12):


22

Figure 3-12 PPTP Settings


Dynamic IP/ Static IP – Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name.

If you choose static IP and enter the domain name, you should also enter the DNS assigned

by your ISP. And click the Save button.


immediately.

Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates.


23


Max Idle Time, since some applications are visiting the Internet continually in the

background.


Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested.



3.4.3 MAC Clone

You can configure the MAC address of the WAN port on this page, Figure 3-13:

Figure 3-13 MAC Address Clone

Some ISPs require that you register the MAC Address of your adapter, which is connected to your

cable/DSL Modem or Ethernet during installation. Changes are rarely needed here.

WAN MAC Address - This field displays the current MAC address of the WAN port, which is

used for the WAN port. If your ISP requires that you register the MAC address, please enter

the correct MAC address into this field. The format for the MAC Address is

XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).

Your PC's MAC Address - This field displays the MAC address of the PC that is managing

the router. If the MAC address is required, you can click the Clone MAC Address button

and this MAC address will fill in the WAN MAC Address field.

Click Restore Factory MAC to restore the MAC address of WAN port to the factory default

value.

Click the Save button to save your settings.

Note: Only the PC on your LAN can use the MAC Address Clone feature.

If you click the Save button, the router will prompt you to reboot.


24

3.5 Wireless

Figure 3-14 Wireless menu

There are three submenus under the Wireless menu (shown in Figure 3-14): Wireless Settings,

MAC Filtering and Wireless Statistics. Click any of them, and you will be able to configure the

corresponding function. The detailed explanations for each submenu are provided below.

3.5.1 Wireless Settings

The basic settings for the wireless network are set on this page, Figure 3-15:

Figure 3-15 Wireless Settings


25

SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all

wireless devices in your network. The default SSID is TP-LINK, but it is recommended

strongly that you change your networks name (SSID) to a different value. This value is

case-sensitive. For example, TP-LINK is NOT the same as tp-link.

Region - Select your region from the pull-down list. This field specifies the region where the

wireless function of the router can be used. It may be illegal to use the wireless function of

the router in a region other than one of those specified in this field. If your country or region

is not listed, please contact your local government agency for assistance.

The default region is United States. When you select your local region from the pull-down list,

Click the Save button, then the Note Dialog appears. Click OK.

Figure 3-16 Note Dialog

Note: Limited by local law regulations, version for North America does not have region selection option.

Channel - This field determines which operating frequency will be used. It is not necessary

to change the wireless channel unless you notice interference problems with another nearby

access point.

Mode - Select the desired wireless mode. The options are:

• 54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can connect to the router.

• 11Mbps (802.11b) - Only 802.11b wireless stations can connect to the router.

Note: The default is "54Mbps (802.11g)", which allows both 802.11g and 802.11b wireless stations to connect to the router.

Enable Wireless Router Radio - The wireless radio of this Router can be enabled or

disabled to allow wireless stations access. If enabled, wireless stations will be able to

access the router. Otherwise, wireless stations will not be able to access.

Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the Wireless

Router SSID will broadcast its name (SSID) on the air.

Enable Bridges – If you select the Enable Bridges checkbox, you can input MAC address

of other APs to communicate with them wirelessly in Bridge mode.

• MAC of AP (1-6): Input the MAC address of the AP which you want to communicate

with. There are six entries can be configured.


26

The APs can communicate with each other in Bridge mode unless they know each other’s

MAC address. For example, if the router whose MAC address is 00-13-56-A8-9E-1A wants

to communicate with an AP whose MAC address is 00-13-56-A8-9E-1B in Bridge mode, you

should do as following:

1. Select Enable Bridges and input 00-13-56-A8-9E-1B as following screen shown.

2. Access the AP's Web-based utility and configure the AP under Bridge mode, then input

00-13-56-A8-9E-1A in corresponding Blank.

Enable Wireless Security – The wireless security function can be enabled or disabled. If

disabled, the wireless stations will be able to connect the router without encryption. It is

recommended strongly that you choose this option to encrypt your wireless network. The

encryption settings are described below.

Security Type - You can select one of the following authentication types:

• WEP - Select WEP authentication type based on 802.11 authentications. • WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type based on pre-shared

passphrase. • WPA /WPA2 - Select WPA/WPA2 authentication type based on Radius Server.

Security Options - You can select one of the following Security options:

• When you select WEP for authentication type you can select the following authentication options:

• Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station request.

• Shared Key - Select 802.11 Shared Key authentication. • Open System - Select 802.11 Open System authentication. • When you select WPA-PSK/WPA2-PSK for authentication type you can select

Automatic, WPA –PSK or WPA2-PSK as authentication options. • When you select WPA/WPA2 as an authentication type you can select Automatic

WPA or WPA2 as authentication option. WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Code Format

stands for any combination of keyboard characters in the specified length. Hexadecimal

format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified

length.


27

WEP Key settings - Select which of the four keys will be used and enter the matching WEP

key information for your network in the selected key radio button. These values must be

identical on all wireless stations in your network.

Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit) for encryption.

"Disabled" means the WEP key entry is invalid.

• For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f,

A-F, zero key is not permitted) or 5 ASCII characters.

• For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9,

a-f, A-F, zero key is not permitted) or 13 ASCII characters.

• For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9,

a-f, A-F, zero key is not permitted) or 16 ASCII characters.

Encryption - When you select WPA-PSK/WPA2-PSK or WPA/WPA2 for Security Type you can select Automatic, TKIP or AES as Encryptions.

Figure 3-17 WPA-PSK/WPA2-PSK

WPA-PSK/WPA2-PSK Passphrase - You can enter a WPA or WPA2 passphrase between

8 and 63 characters long.

Group Key Update Period - Specify the group key update interval in seconds. The value

can be either 0 seconds or from 30 seconds and up, 1-29 seconds are not usable figures.

Enter 0 to disable the update.

Figure 3-18 WPA/WPA2

Radius Server IP - Enter the IP address of the Radius Server


28

Radius Port - Enter the port number that the radius service used. Radius Password - Enter the password for the Radius Server.

Be sure to click the Save button to save your settings on this page.

Note: The router will reboot automatically after you click save.

3.5.2 MAC Filtering

The Wireless MAC Filtering for wireless networks are set on this page, Figure 3-19:

Figure 3-19 Wireless MAC address Filtering

The Wireless MAC Address Filtering feature allows you to control wireless stations accessing the

router, which depend on the station's MAC addresses.

MAC Address - The wireless station's MAC address that you want to access.

Status - The status of this entry either Enabled or Disabled.

Privilege - Select the privileges for this entry. You may select one of the following Allow / Deny / 64-bit / 128-bit / 152-bit.

Description - A simple description of the wireless station.

WEP Key - Specify a unique WEP key (in Hexadecimal format) to access the router.

To set up an entry, follow these instructions:

First, you must decide whether the unspecified wireless stations can access the router or not. If

you desire that the unspecified wireless stations can access the router, please select the radio

button Allow the stations not specified by any enabled entries in the list to access,

otherwise, select the radio button Deny the stations not specified by any enabled entries in the list to access.

To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 3-18:


29

Figure 3-20 Add or Modify Wireless MAC Address Filtering entry

To add or modify a MAC Address Filtering entry, follow these instructions:

1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B.

2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A.

3. Privilege - Select the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit. 4. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any

combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. For example: 2F34D20BE2.

5. Status - Select Enabled or Disabled for this entry on the Status pull-down list. 6. Click the Save button to save this entry.

Note: When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled.

To modify or delete an existing entry:

1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete.

2. Modify the information.

3. Click the Save button.

Click the Enable All button to make all entries enabled

Click the Disabled All button to make all entries disabled.

Click the Delete All button to delete all entries

Click the Next button to go to the next page and click the Previous button to return to the

previous page.

For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be

able to access the router. The wireless station B with MAC address 00-0A-EB- 00-07-5F not be able

to access the router, and the wireless station C with MAC address 00-0A-EB-00-07-8A be able to

access the router when its WEP key is 2F34D20BE2E 54B326C5476586A, while all other wireless

stations cannot access the router, you should configure the Wireless MAC Address Filtering list


30

by following these steps:

1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list

to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC

Address field, enter wireless station A in the Description field, select Allow in the Privilege pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return button.

5. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-5F in the MAC Address field, enter wireless station B in the Description field, select Deny in the Privilege pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return button.

6. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-8A in the MAC Address field, enter wireless station C in the Description field, select 128-bit in the Privilege pull-down list, enter 2F34D20BE2E54B326C5476586A in the WEP Key field and select Enabled in the Status pull-down list. Click the Save and the Return button. The filtering rules that configured should be similar to the following list:

Note: If you select the radio button Allow the stations not specified by any enabled entries in the list to access for Filtering Rules, the wireless station B will still not be able to access the router, however, other wireless stations that are not in the list will be able to access the router.

If you enable the function and select the Deny the stations not specified by any enabled entries in the list to access for Filtering Rules, and there are not any enable entries in the list, thus, no wireless stations can access the router.

3.5.3 Wireless Statistics

This page shows MAC Address, Current Status, Received Packets and Sent Packets for each

connected wireless station.

Figure 3-21 The router attached wireless stations

MAC Address - The connected wireless station's MAC address


31

Current Status - The connected wireless station's running status, one of STA-AUTH /

STA-ASSOC / AP-UP / WPA / WPA-PSK /WPA2/WPA2-PSK/None

Received Packets - Packets received by the station

Sent Packets - Packets sent by the station

You cannot change any of the values on this page. To update this page and to show the current

connected wireless stations, click on the Refresh button.

If the numbers of connected wireless stations go beyond one page, click the Next button to go to

the next page and click the Previous button to return the previous page.

Note: This page will be refreshed automatically every 5 seconds.

3.6 DHCP

Figure 3-22 The DHCP menu

There are three submenus under the DHCP menu (shown in Figure 3-22): DHCP Settings,

DHCP Clients List and Address Reservation. Click any of them, and you will be able to

configure the corresponding function. The detailed explanations for each submenu are provided

below.

3.6.1 DHCP Settings

The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which

provides the TCP/IP configuration for all the PC(s) that are connected to the router on the LAN.

The DHCP Server can be configured on the page (shown in Figure 3-23):

Figure 3-23 DHCP Settings

DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must


32

have another DHCP server within your network or else you must manually configure the computer.

Start IP Address - This field specifies the first of the addresses in the IP address pool. 192.168.1.100 is the default start address.

End IP Address - This field specifies the last of the addresses in the IP address pool. 192.168.1.199 is the default end address.

Address Lease Time - The Address Lease Time is the amount of time in which a network user will be allowed connection to the router with their current dynamic IP Address. Enter the amount of time, in minutes. The user will be "leased" this dynamic IP Address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the router, default value is 192.168.1.1

Default Domain - (Optional.) Input the domain name of your network. Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your

ISP. Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP

provides two DNS servers.

Note: To use the DHCP server function of the router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. This function will take effect until the router reboots.

3.6.2 DHCP Clients List

This page shows Client Name, MAC Address, Assigned IP, and Lease Time for each DHCP

Client attached to the router (Figure 3-24):

Figure 3-24 DHCP Clients List

Index - The index of the DHCP Client

Client Name - The name of the DHCP client

MAC Address - The MAC address of the DHCP client

Assigned IP - The IP address that the router has allocated to the DHCP client.

Lease Time - The time of the DHCP client leased. Before the time is up, DHCP client will

request to renew the lease automatically.

You cannot change any of the values on this page. To update this page and to show the current

attached devices, click on the Refresh button.


33

3.6.3 Address Reservation

When you specify a reserved IP address for a PC on the LAN, that PC will always receive the

same IP address each time when it accesses the DHCP server. Reserved IP addresses should

be assigned to servers that require permanent IP settings. This page is used for address

reservation (shown in Figure 3-25).

Figure 3-25 Address Reservation

MAC Address - The MAC address of the PC of which you want to reserve IP address.

Assigned IP Address - The IP address of the router reserved.


To Reserve IP addresses:

1. Click the Add New button. (Pop-up Figure 3-26) 2. Enter the MAC address (The format for the MAC Address is XX-XX-XX-XX-XX-XX.) and IP

address in dotted-decimal notation of the computer you wish to add. 3. Click the Save button when finished.

Figure 3-26 Add or Modify an Address Reservation Entry








34


Click the Next button to go to the next page and Click the Previous button to return the previous

Note: The function won't take effect until the router reboots.

3.7 Forwarding

Figure 3-27 The Forwarding menu

There are four submenus under the Forwarding menu (shown in Figure 3-27): Virtual Servers,

Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the


3.7.1 Virtual Servers

Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and

FTP. A virtual server is defined as a service port, and all requests from the Internet to this service

port will be redirected to the computer specified by the server IP. Any PC that was used for a

virtual server must have a static or reserved IP Address because its IP Address may change

when using the DHCP function. You can set up virtual servers on this page, shown in Figure

3-28:

Figure 3-28 Virtual Servers

Service Port - The numbers of External Ports. You can type a service port or a range of service ports (the format is XXX – YYY, XXX is the start port, YYY is the end port).

IP Address - The IP Address of the PC providing the service application. Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols

supported by the router). Status - The status of this entry either Enabled or Disabled.

To setup a virtual server entry:

1. Click the Add New button. (pop-up Figure 3-29) 2. Select the service you want to use from the Common Service Port list. If the Common


35

Service Port list does not have the service that you want to use, type the number of the service port or service port range in the Service Port box.

3. Type the IP Address of the computer in the Server IP Address box. 4. Select the protocol used for this application, either TCP or UDP, or All. 5. Select the Enable checkbox to enable the virtual server. 6. Click the Save button.

Figure 3-29 Add or Modify a Virtual Server Entry

Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and enter the same IP Address for that computer or server.








Click the Next button to go to the next page and Click the Previous button to return the previous

page.

Note: If you set the virtual server of service port as 80, you must set the Web management port on Security –> Remote Management page to be any value except 80 such as 8080. Or else there will be a conflict to disable the virtual server.

3.7.2 Port Triggering

Some applications require multiple connections, like Internet games, video conferencing, Internet

calling and so on. These applications cannot work with a pure NAT router. Port Triggering is

used for some of these applications that can work with an NAT router. You can set up Port

Triggering on this page shown in Figure 3-30:


36

Figure 3-30 Port Triggering

Once configured, operation is as follows:

1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field.

2. The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host.

3. When necessary the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field.

Trigger Port - The port for outgoing traffic. An outgoing connection using this port will "Trigger" this rule.

Trigger Protocol - The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router).

Incoming Ports Range - The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port section). Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085, 3010-3030.

Incoming Protocol - The protocol used for Incoming Ports Range, either TCP or UDP, or ALL (all protocols supported by the router).


To add a new rule, enter the following data on the Port Triggering screen.

1. Click the Add New button. (pop-up Figure 3-31) 2. Enter a port number used by the application when it generates an outgoing request. 3. Select the protocol used for Trigger Port from the pull-down list, either TCP, UDP, or All. 4. Enter the range of port numbers used by the remote system when it responds to the PC's

request. 5. Select the protocol used for Incoming Ports Range from the pull-down list, either TCP or

UDP, or All. 6. Select the Enable checkbox to enable. 7. Click the Save button to save the new rule.


37

Figure 3-31 Add or Modify a Triggering Entry

There are many popular applications in the Popular Application list. You can select it, and the

application will fill in the Trigger Port, incoming Ports Range boxes and select the Enable

checkbox. It has the same effect as adding a new rule.








Note: When the trigger connection is released, the according opening ports will be closed.

Each rule allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused.

Incoming Port Range cannot overlap each other.

3.7.3 DMZ

The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose

service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the

same time. Any PC whose port is being forwarded must have its DHCP client function disabled

and should have a new static IP Address assigned to it because its IP Address may change when

using the DHCP function. You can set up DMZ host on this page shown in figure 5-29:


38

Figure 3-32 DMZ

To assign a computer or server to be a DMZ server:

1. Click the Enable radio button 2. Enter the local host IP Address in the DMZ Host IP Address field

Note: After you set the DMZ host, the firewall related to the host will not work.

3.7.4 UPnP

The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to

access the local host resources or devices as needed. UPnP devices can be automatically

discovered by the UPnP service application on the LAN. You can configure UPnP on this page

that shown in Figure 3-33:

Figure 3-33 UPnP Settings

Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable

button. As allowing this may present a risk to security, this feature is disabled by default.

Current UPnP Settings List - This table displays the current UPnP information.

• App Description – The description provided by the application in the UPnP request

• External Port - External port, which the router opened for the application.

• Protocol – Shows which type of protocol is opened.

• Internal Port - Internal port, which the router opened for local host.

• IP Address - The UPnP device that is currently accessing the router.

• Status - Either Enabled or Disabled, “Enabled” means that port is still active. Otherwise,

the port is inactive.

Click Refresh to update the Current UPnP Settings List.


39

3.8 Security

Figure 3-34 The Security menu

There are six submenus under the Security menu (shown in Figure 3-34): Firewall, IP Address Filtering, Domain Filtering, MAC Filtering, Remote Management and Advanced Security. Click any of them, and you will be able to configure the corresponding function. The detailed

explanations for each submenu are provided below.

3.8.1 Firewall

Using the Firewall page (shown in Figure 3-35), you can turn the general firewall switch on or off.

The default setting for the switch is off. If the general firewall switch is off, even if IP Address

Filtering, DNS Filtering and MAC Filtering are enabled, their settings are ineffective.

Figure 3-35 Firewall Settings

Enable Firewall - the general firewall switch is on or off. Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two

default filtering rules of IP Address Filtering, either Allow or Deny passing through the router. Enable Domain Filtering - set Domain Filtering is enabled or disabled.


40

Enable MAC Filtering - set MAC Address Filtering is enabled or disabled. You can select the default filtering rules of MAC Address Filtering, either Allow or Deny accessing the router.

3.8.2 IP Address Filtering

The IP address Filtering feature allows you to control Internet Access by specific users on your

LAN based on their IP addresses. The IP address filtering is set on this page, Figure 3-36:

Figure 3-36 IP address Filtering

To disable the IP Address Filtering feature, keep the default setting, Disabled. To set up an IP

Address Filtering entry, click Enable Firewall and Enable IP Address Filtering on the Firewall

page, and click the Add New… button. The page "Add or Modify an IP Address Filtering entry"

will appear shown in Figure 3-37:

Figure 3-37 Add or Modify an IP Address Filtering Entry

To create or modify an IP Address Filtering entry, please follow these instructions:

1. Effective Time - Enter a range of time in HHMM format, which point to the range time for the entry to take effect. For example, 0803 - 1705, the entry will take effect from 08:03 to 17:05.

2. LAN IP Address - Enter a LAN IP Address or a range of LAN IP addresses in the field, in dotted-decimal notation format. For example, 192.168.1.20 - 192.168.1.30. Keep the field


41

open, which means all LAN IP Addresses have been put into the field. 3. LAN Port - Enter a LAN Port or a range of LAN ports in the field. For example, 1030 - 2000.

Keep the field open, which means all LAN ports have been put into the field. 4. WAN IP Address - Enter a WAN IP Address or a range of WAN IP Addresses in the field, in

dotted-decimal notation format. For example, 61.145.238.6 – 61.145.238.47. Keep the field open, which means all WAN IP Addresses have been put into the field.

5. WAN Port - Enter a WAN Port or a range of WAN Ports in the field. For example, 25 – 110. Keep the field open, which means all WAN Ports have been put into the field.

6. Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols supported by the router).

7. Action - Select either Allow or Deny through the router. 8. Status - Select Enabled or Disabled for this entry on the Status pull-down list. 9. Click the Save button to save this entry. To modify or delete an existing entry:







You can change the entry’s order as desired. Fore entries are before hind entries. Enter the ID

number in the first box you want to move and another ID number in second box you want to move

to, and then click the Move button to change the entry’s order.

Click the Next button to the next page and click the Previous button to return to the previous

page.

For example: If you desire to block E-mail received and sent by the IP Address 192.168.1.7 on

your local network, and to make the PC with IP Address 192.168.1.8 unable to visit the website of

IP Address 202.96.134.12, while other PC(s) have no limit you should specify the following IP

address filtering list:

3.8.3 Domain Filtering

The Domain Filtering page (shown in Figure 3-38) allows you to control access to certain websites

on the Internet by specifying their domains or key words.


42

Figure 3-38 Domain Filtering

Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable

Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, click

the Add New… button. The page "Add or Modify a Domain Filtering entry " will appear, shown

in Figure 3-39:

Figure 3-39 Add or Modify a Domain Filtering entry

To add or modify a Domain Filtering entry, follow these instructions:

1. Effective Time - Enter a range of time in HHMM format specifying the time for the entry to take effect. For example, if you enter: 0803 - 1705, than the entry will take effect from 08:03 to 17:05.

2. Domain Name - Type the domain or key word as desired in the field. A blank in the domain field means all websites on the Internet. For example: www.xxyy.com.cn, .net.

3. Status - Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry.





Click the Enabled All button to make all entries enabled.


http://www.xxyy.com.cn/


43


Click the Next button to go to the next page and the Previous button to return to the previous

page.

For example: if you want to block the PC(s) on your LAN to access websites www.xxyy.com.cn,

www.aabbcc.com and websites with .net in the end on the Internet while no limit for other

websites, you should specify the following Domain filtering list:

3.8.4 MAC Filtering

Like the IP Address Filtering page, the MAC Address Filtering page (shown in Figure 3-40) allows

you to control access to the Internet by users on your local network based on their MAC Address.

Figure 3-40 MAC address Filtering

Before setting up MAC Filtering entries, you must ensure that Enable Firewall and Enable MAC

Filtering have been selected on the Firewall page. To Add a MAC Address filtering entry, clicking

the Add New… button. The page "Add or Modify a MAC Address Filtering entry" will appear,

shown in Figure 3-41:

Figure 3-41 Add or Modify a MAC Address Filtering entry

http://www.xxyy.com.cn/

http://www.aabbcc.com/


44

To add or modify a MAC Address Filtering entry, follow these instructions:

1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0E-AE-B0-00-0B.

2. Type the description of the PC in the Description field. Fox example: John’s PC. 3. Status - Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry.

To add additional entries, repeat steps 1-4.

When finished, click the Return button to return to the MAC Address Filtering page.





Click the Enable All button to make all entries enabled.



Click the Next button to go to the next page and click the Previous button to return to the

previous page.

Fox example: If you want to block the PC with MAC addresses 00-0A-EB-00-07-BE and

00-0A-EB-00-07-5F to access the Internet, first, enable the Firewall and MAC Address Filtering

on the Firewall page, then, you should specify the Default MAC Address Filtering Rule "Deny these PC(s) with effective rules to access the Internet" on the Firewall page and the following

MAC address filtering list on this page:

3.8.5 Remote Management

You can configure the Remote Management function on this page shown in Figure 3-42. This

feature allows you to manage your Router from a remote location, via the Internet.

Figure 3-42 Remote Management


45

Web Management Port - Web browser access normally uses the standard HTTP service

port 80. This router’s default remote management Web port number is 80. For greater

security, you can change the remote management Web interface to a custom port by

entering that number in this box provided. Choose a number between 1024 and 65534, but

do not use the number of any common service port.

Remote Management IP Address - This is the current address you will use when

accessing your router from the Internet. The default IP Address is 0.0.0.0. It means this

function is disabled. To enable this function, change the default IP Address to another IP

Address as desired.

To access the router, you will type your router's WAN IP Address into your browser's Address

(in IE) or Location (in Navigator) box, followed by a colon and the custom port number. For

example, if your Router's WAN address is 202.96.12.8 and you use port number 8080, enter in

your browser: http://202.96.12.8:8080. You will be asked for the router's password. After

successfully entering the password, you will be able to access the router's Web-based utility.

Note: Be sure to change the router's default password to a very secure password.

3.8.6 Advanced Security

Using Advanced Security page (shown in Figure 3-43), you can protect the router from being

attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood from LAN.

Figure 3-43 Advanced Security settings

Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and

http://202.96.12.8:8080/


46

60 seconds in the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic. The result of the statistic used for analysis by SYN Flood, UDP Flood and ICMP-Flood.

DoS protection - Enable or Disable the DoS protection function. Only when it is enabled, will the flood filters be effective.

Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack Filtering.

ICMP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current ICMP-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately.

Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering. UDP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value

between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately.

Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN- FLOOD Attack Filtering.

TCP-SYN-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately.

Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port. The default is disabled. If enabled, the ping packet from the Internet cannot access the router.

Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LAN port. The default value is disabled. If enabled, the ping packet from the LAN port cannot access the router. (Defends against some viruses)

Click the Save button to save the settings.

Click the Blocked DoS Host Table button to display the DoS host table by blocking. The page

will appear that shown in Figure 3-44:

Figure 3-44 Thwarted DoS Host Table

This page shows Host IP Address and Host MAC Address for each host blocked by the router.

Host IP Address- The IP address that blocked by DoS are displayed here.

Host MAC Address - The MAC address that blocked by DoS are displayed here.

To update this page and to show the current blocked host, click on the Refresh button.

Click the Clear All button to clear all displayed entries. After the table is empty the blocked host


47

will regain the capability to access Internet.

Click the Return button to return to the Advanced Security page.

3.9 IP & MAC Binding Setting

Figure 3-45 the IP & MAC Binding menu

There are two submenus under the IP &MAC Binding menu (shown in Figure 3-45): Binding Setting and ARP List. Click any of them, and you will be able to scan or configure the


3.9.1 Binding Setting

This page displays the IP & MAC Binding Setting table; you can operate it in accord with your

desire. (shown in Figure 3-46).

Figure 3-46 IP & MAC Binding Setting

MAC Address - The MAC address of the controlled computer in the LAN.

IP Address - The assigned IP address of the controlled computer in the LAN.

Bind - Whether or not enable the arp binding.

Modify - Edit or delete item.

When you want to add or modify an IP & MAC Binding entry, you can click the Add New button

or Modify button, and then you will go to the next page. This page is used for adding or

modifying an IP & MAC Binding entry (shown in Figure 3-47).


48

Figure 3-47 IP & MAC Binding Setting (Add & Modify)

To add IP & MAC Binding entries:

1. Click the Add New.. button.

2. Enter the MAC Address and IP Address.

3. Select the Bind checkbox.

4. Click the Save button to save it.


1. Find the desired entry in the table.

2. Click Modify or Delete as desired on the Modify column.

To find an existing entry:

1. Click the Find button (shown in Figure 3-47).

2. Enter the MAC Address or IP Address.

3. Enter the Find button in the next page (shown in Figure 3-48).

Figure 3-48 Find IP & MAC Binding Entry


Click the Delete All button to delete all entries.


49

3.9.2 ARP List

To manage the computer, you could observe the computers in the LAN by checking the

relationship of MAC address and IP address on the ARP list, and you could configure the items on

the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding

entries (shown in Figure 3-49).

Figure 3-49 ARP List

MAC Address - The MAC address of the controlled computer in the LAN.

IP Address - The assigned IP address of the controlled computer in the LAN.

Status - Enabled or Disabled of the MAC address and IP address binding.

Configure - Load or delete item.

Load - Load the item to the IP & MAC Binding list.

Delete - Delete the item.

1. Click the Bind All button to bind all the current items, available after enable.

2. Click the Load All button to load all items to the IP & MAC Binding list.

3. Click the Refresh button to refresh all items.

Note: An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without interference to the IP & MAC Binding list

3.10 Routing

A static route is a pre-determined path that network information must travel to reach a specific host or network. To add or delete a route, work in the area under the Static Routing page (shown in Figure 3-50).


50

Figure 3-50 Static Routing

To add static routing entries:

1. Click the Add New button. (pop-up Figure 3-51)

2. Enter the following data:

Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.

Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.

Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host.

3. Select Enabled or Disabled for this entry on the Status pull-down list.

4. Click the Save button to save it.

Figure 3-51 Add or Modify a Static Route Entry









51

3.11 DDNS

The router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed

host and domain name to a dynamic Internet IP Address. It is useful when you are hosting your

own website, FTP server, or other server behind the router. Before using this feature, you need to

sign up for DDNS service providers such as www.dyndns.org, www.oray.net or www.comexe.cn.

The Dynamic DNS client service provider will give you a password or key.

To set up for DDNS, follow these instructions:

3.11.1 Dyndns.org DDNS

If your selected dynamic DNS Service Provider is www.dyndns.org, the page will appear as


Figure 3-52 Dyndns.org DDNS Settings


1. Type the domain names your dynamic DNS service provider gave. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to login to the DDNS service.

Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service.

3.11.2 Oray.net DDNS

If your selected dynamic DNS Service Provider is www.oray.net, the page will appear as shown

in Figure 3-53:

http://www.oray.net/

http://www.comexe.cn/

http://www.dyndns.org/



52

Figure 3-53 Oray.net DDNS Settings


1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Click the Login button to login the DDNS service.

Connection Status - The status of the DDNS service connection is displayed here. Domain Name - The domain names are displayed here.

Click Logout to logout the DDNS service.

3.11.3 Comexe.cn DDNS

If your selected dynamic DNS Service Provider is www.comexe.cn, the page will appear as




53

Figure 3-54 Comexe.cn DDNS Settings


1. Type the domain names your dynamic DNS service provider gave. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to login to the DDNS service.

Connection Status -The status of the DDNS service connection is displayed here.

Click Logout to logout of the DDNS service.

3.12 System Tools

Figure 3-55 The System Tools menu

There are eight submenus under the System Tools menu (shown in Figure 3-55): Time,

Firmware, Factory Defaults, Backup and Restore, Reboot, Password, Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed


54

explanations for each submenu are provided below.

3.12.1 Time

You can set time manually or get GMT from the Internet for the router on this page (shown in

Figure 3-56):

Figure 3-56 Time settings

Time Zone - Select your local time zone from this pull down list. Date - Enter your local date in MM/DD/YY into the right blanks. Time - Enter your local time in HH/MM/SS into the right blanks.

Time setting follows these steps below:

1. Select your local time zone. 2. Enter date and time in the right blanks 3. Click Save.

Click the Get GMT button to get GMT time from Internet if you have connected to Internet.

If you’re using Daylight saving time, please follow the steps below.

1. Select using daylight saving time. 2. Enter daylight saving beginning time and end time in the right blanks. 3. Click Save.

Note: This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, if not, the time limited on these functions will not take effect.

1. The time will be lost if the router is turned off. 2. The router will obtain GMT automatically from Internet if it has already connected to

Internet.


55

3.12.2 Firmware

The page (shown in Figure 3-57) allows you to upgrade the latest version firmware to keep your

router up-to-date.

Figure 3-57 Firmware Upgrade

New firmware is posted at www.tp-link.com and can be downloaded for free. If the router is not

experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports

a new feature you need.

Note: When you upgrade the router's firmware, you will lose current configuration settings, so make sure you backup the router’s settings before you upgrade its firmware.

To upgrade the router's firmware, follow these instructions:

1. Download the latest firmware upgrade file from the TP-LINK website www.tp-link.com. 2. Click Browse to view the folders and select the downloaded file. 3. Click the Upgrade button.

Firmware Version - Displays the current firmware version. Hardware Version - Displays the current hardware version. The hardware version of the

upgrade file must accord with the current hardware version.

Note: Do not turn off the router or press the Reset button while the firmware is being upgraded.

The router will reboot after the Upgrading has been finished.

3.12.3 Factory Defaults

This page (shown in Figure 3-58) allows you to restore the factory default settings for the router.

http://www.tp-link.com/


56

Figure 3-58 Restore Factory Default

Click the Restore button to reset all configuration settings to their default values.

The default User Name: admin

The default Password: admin

The default IP Address: 192.168.1.1

The default Subnet Mask: 255.255.255.0

Note: Any settings you have saved will be lost when the default settings are restored.

3.12.4 Backup and Restore

This page (shown in Figure 3-59) allows you to save current configuration of router as backup or

restore the configuration file you saved before.

Figure 3-59 Backup & Restore Configuration

Click the Backup button to save all configuration settings as a backup file in your local computer.

To restore the router's configuration, follow these instructions:

1 Click the Browse button to select the backup file which you want to restore. 2 Click the Restore button.

Note: The current configuration will be covered with the uploading configuration file. The restoration process lasts for 20 seconds and the router will restart automatically. Keep the router on during the restoring process, to prevent any damage.

3.12.5 Reboot

This page (shown in Figure 3-60) allows you to reboot the router.


57

Figure 3-60 Reboot the router

Click the Reboot button to reboot the router.

Some settings of the router will take effect only after rebooting, which include:

Change LAN IP Address. (System will reboot automatically)

MAC Clone (system will reboot automatically)

DHCP service function.

Static address assignment of DHCP server.

Web Service Port of the router.

Upgrade the firmware of the router (system will reboot automatically).

Restore the router's settings to factory default (system will reboot automatically).

3.12.6 Password

This page (shown in Figure 3-61) allows you to change the factory default user name and

password of the router.

Figure 3-61 Password

It is recommended strongly that you change the factory default user name and password of the router. All users who try to access the router's Web-based utility or Quick Setup will be prompted

Note: The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it.

Click the Save button when finished. Click the Clear All button to clear all.


58

3.12.7 Log

This page (shown in Figure 3-62) allows you to query the logs of the router.

Figure 3-62 System Log

The router can keep logs of all traffic. You can query the logs to find what happened to the router.

Click the Refresh button to refresh the logs.

Click the Clear Log button to clear all the logs.

3.12.8 Statistics

The Statistics page (shown in Figure 3-63) displays the network traffic of each PC in LAN,

including total traffic and traffic of the last Packets Statistic interval seconds.

Figure 3-63 Statistics

Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click

the Enable button. If disabled, the function of DoS protection in Security settings will be


59

ineffective.

Packets Statistics Interval - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval indicates the time section of the packets statistic.

Sorted Rules - Here displays sort as desired.

Statistics Table:

IP Address The IP Address displayed with statistics

Packets The total amount of packets received and transmitted by the router. Total

Bytes The total amount of bytes received and transmitted by the router.

Packets The total amount of packets received and transmitted in the last Packets Statistic interval seconds.

Bytes The total amount of bytes received and transmitted in the last Packets Statistic interval seconds.

ICMP Tx The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds.

UDP Tx The total amount of the UDP packets transmitted to WAN in the last Packets Statistic interval seconds.

Current

TCP SYN Tx The total amount of the TCP SYN packets transmitted to WAN in the last Packets Statistic interval seconds.

Click the Save button to save the Packets Statistic interval value.

Click the Auto-refresh checkbox to refresh automatically.

Click the Refresh button to refresh immediately.


60

Appendix A: Glossary Access Point - A device that allows wireless-equipped computers and other devices to

communicate with a wired network. Also used to expand the range of a wireless network.

Ad-hoc Network - An ad-hoc network is a group of computers, each with a wireless adapter,

connected as an independent IEEE 802.11 wireless LAN. Ad-hoc wireless computers operate on

a peer-to-peer basis, communicating directly with each other without the use of an access point.

Ad-hoc mode is also referred to as an Independent Basic Service Set (IBSS) or as peer-to-peer

mode, and is useful at a departmental scale or SOHO operation.

AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block

data encryption.

ATM (Asynchronous Transfer Mode) - ATM is a cell based transfer mode that requires variable

length user information to be segmented and reassembled to/from short, fixed length cells. It uses

two different methods for carrying connectionless network interconnect traffic, routed and bridged

Protocol Data Units (PDUs), over an ATM network.

Bridging - A device that connects different networks.

Browser - An application program that provides a way to look at and interact with all the

information on the World Wide Web.

DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail

server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address.

Default Gateway - A device that forwards Internet traffic from your local area network.

DHCP - A networking protocol that allows administrators to assign temporary IP addresses to

network computers by “leasing” an IP address to a user for a limited amount of time, instead of

assigning permanent IP addresses.

DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to

be “seen” from the Internet.

DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names

of websites into IP addresses.

Note: Now, all the configurations are finished, it will take effect after reboot.


61

Appendix B: Specifications General

Standards and Protocols IEEE 802.3,IEEE 802.3u, IEEE 802.11b and IEEE 802.11g

TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP

Safety & Emission FCC、CE

LEDs Power, SYS, WLAN, WAN, 1-4

Ports One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M

Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX

Wireless

Modulation IEEE 802.11b: DQPSK, DBPSK, DSSS, and CCK

IEEE 802.11g: BPSK, QPSK, 16QAM, 64QAM, OFDM

Frequency 2400 ~ 2483.5MHz

Channels 13

Wireless Data Rates IEEE 802.11b: 11, 5.5, 2, and 1Mbps

IEEE 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps

Media Access Protocol CSMA/CA with ACK

Security WEP/WPA/WPA2

Physical and Environment

Working Temperature 0℃~40℃ (32 ~104℉ ℉)

Storage Temperature -40℃~70℃（-40℉~158℉）

Working Humidity 10% - 90% RH, Non-condensin

Storage Humidity 5% - 90% RH, Non-condensing

Dimensions (L x W x H) 4.17×4.01×1.10in. (160×102×28 mm) (without antenna)


Appendix C: FAQ 1. How do I configure the router to access Internet by ADSL users?

1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The

telephone cord plugs into the Line port of the ADSL Modem. 3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN"

submenu. On the WAN page, select “PPPoE” for WAN Connection Type. Type user name in the “User Name” field and password in the “Password” field, finish by clicking “Connect”.

PPPoE Connection Type

4) If your ADSL lease is in “pay-according-time” mode, select “Connect on Demand” or “Connect Manually” for Internet connection mode. Type an appropriate number for “Max Idle Time” to avoid wasting paid time. Otherwise, you can select “Auto-connecting” for Internet connection mode.

PPPoE Connection Mode

Note: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications is visiting the Internet continually in the background.

If you are a Cable user, please configure the router following the above steps.

2. How do I configure the router to access Internet by Ethernet users?

1) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”.

2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation. If your ISP requires MAC

62


63

register, login to the router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link. On the "MAC Clone" page, if your PC’s MAC address is proper MAC address, click the "Clone MAC Address" button and your PC’s MAC address will fill in the "WAN MAC Address" field. Or else, type the MAC Address into the "WAN MAC Address" field. The format for the MAC Address is XX-XX-XX-XX-XX-XX. Then click the "Save" button. It will take effect after rebooting.

MAC Clone

3. I want to use Netmeeting, what do I need to do?

1) If you start Netmeeting as a sponsor, you don’t need to do anything with the router. 2) If you start as a response, you need to configure Virtual Server or DMZ Host. 3) How to configure Virtual Server: Login to the router, click the “Forwarding” menu on the

left of your browser, and click "Virtual Servers" submenu. On the "Virtual Server" page, click Add New, then on the “Add or Modify a Virtual Server” page, enter “1720” into the blank behind the “Service Port”, and your IP address behind the IP Address, assuming 192.168.1.169 for an example, remember to “Enable” and “Save”.

Virtual Servers

Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page.

4. How to enable DMZ Host ？

Login to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ"

submenu. On the "DMZ" page, click “Enable” radio and type your IP address into the “DMZ Host

IP Address” field, using 192.168.1.169 as an example, remember to click the "Save” button.

DMZ


64

5. I want to build a WEB Server on the LAN, what should I do?

Because the WEB Server port 80 will interfere with the WEB management port 80 on the router,

you must change the WEB management port number to avoid interference.

To change the WEB management port number: Login to the router, click the “Security” menu on

the left of your browser, and click "Remote Management" submenu. On the "Remote

Management" page, type a port number except 80, such as 88, into the "Web Management Port"

field. Click “Save” and reboot the router.

Remote Management

Note: If the above configuration takes effect, to configure to the router by typing http://192.168.1.1:88 in the address field of the web browser.

Login to the router, click the “Forwarding” menu on the left of your browser, and click the "Virtual

Servers" submenu. On the "Virtual Server" page, enter “80” into the blank below the “Service Port”,

and your IP address below the IP Address, assuming 192.168.1.1 : 88 for an example,

remember to “Enable” and “Save”.

Virtual Server

http://www.tp-link.com

http://www.tp-link.com/

Download - TL- WR340G user manual.pdf

Top Related