-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
1/10
DOCUMENT CODE: TS 1-08
EDITION: I PAGE: 1 of 10
QUALITY MANAGEMENT SYSTEM CONFIDENTIALITY:p.t. STATUS (COPY NO.):AUTHOR : Aleksej Ermolaev, Manager of Quality ManagementDepartmentSIGNATURE:
CONTROLED BY: Aleksej Ermolaev, Representative of QualityManagementSIGNATURE:
APPROVED BY :Bojan Zeevi, Zamenik GD za proizvodnjuSIGNATURE:
DATE:. 10.04. 2008. SUPERIOR DOCUMENT: P-05
Technical (construction) specification of the steel rebars and plain barsfor the reinforcement of concrete
of the Metalfer Steel Mill production
TS 1-08
CHANGE NO.: APPROVED BY: DATE CHANGE NO.: APPROVED BY: DATE:
1 A.Ermolaev 20.08.2008
2 A.Ermolaev 29.12.2008
3 I. Romandi 09.12.2010
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
2/10
1. General demandsSpecification covers weldable steel rebars and wire rod for concrete armouring, produced in accor-
dance with following standards:
- B500B Acc. to SRPS EN 10080, grade B500A (rib like B500B),
- B500B Acc. to BS 4449-2005,
- B500B Acc. to DIN 488-2009,
- PC 52 Acc. to STAS 438/1-89; OB37 Acc. to STAS 438/1-89,- B60.50 Acc. to MSZ 339-1987.
It can be according to other standards if the customer wishes so, and the technical possibilities of
Metalfer Steel Mill allow it.
When negotiating, the rebars must be defined in single-value, like the following example shows:
Example of the mark: "Rebar 14x12 000 SRPS EN 10080 Grade B500B".
1.1. Construction and technical accordance95% of the produced rebars must be in accordance with this specification. Production is performed
according to technical documentation developed and approved by Metalfer Steel Mill. For data that are
not mentioned in this specification (like dimensions, tolerance and marks), rebar production standard
gives the data.
1.2. Production range1.2.1. Nominal standard diameters of the rebar can be: 8, 10, 12, 14, 16, 18, 20, 22, 25, 28 and 32.
Other diameters can be produced if the customer requires.
1.2.2. Standard length is 12m, but shorter rebars can be delivered if the customer requires.
1.3. Terms and definitions
Terms and definitions, such as: chemical composition, sampling, retesting, performance, dimensions,
weight per meter, tolerance, surface geometry, accordance determination, methods of examination and
identification, are in accordance with B500B Acc. to SRPS EN 10080; B500B Acc. to BS 4449:2005;
B500B Acc. to DIN 488-1:2009; B60.50 Acc. to MSZ 339:1987; PC 52 Acc. to STAS 438/1-89; OB
37 Acc. to STAS 438/1-89.
2. Appearance of the steel rebar
Image 1Geometric shape of the steel rib B500B, B500A, 460B
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
3/10
Image 3Geometric shape of the steel rib B 60.50 according to MSZ 339-87
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
4/10
PC 52 according to STAS 438/1-89
B500B according DIN 488
Geometry profile according to DIN 488:2009
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
5/10
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
6/10
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
7/10
4. Chemical composition and mechanical propertiesMechanical examinations are performed at universal test machine MUT-E 1
stclass according to standard EN ISO 15630-1:
a) yield strength (YS)Re (MPa, N/mm2);
b)tensile strength (TS)Rm (MPa, N/mm
2);
c) rate (R)Rm/ Re;
d) percent of the total elongation at maximum force (EMF) Agt (%)
d) elongation after fracture - A5 (%)
C Mn Si S P Cr Ni Cu N Ceq YS TS YS/TS A5 Agtmin 0,14 0,5 0,10 0,28 500 1,05 2,5
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,80 0,012 0,50min 0,14 0,5 0,10 0,28 500 1,08 5,0
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,80 0,012 0,50
min 0,14 0,5 0,10 0,28 460 1,05 12 2,5
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,80 0,012 0,50
min 0,14 0,5 0,10 0,28 460 1,08 14 5,0
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,80 0,012 0,50
min 0,14 0,5 0,10 0,28 500 1,05 10
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,60 0,012 0,50
min 0,14 0,5 0,10 0,28 500 1,08 10
max 0,22 0,8 0,30 0,050 0,050 0,30 0,30 0,60 0,012 0,50
min 0,14 0,35 255 360 25
max 0,23 0,75 0,07 0,045 0,045 0,30 0,30
min 0,14 0,40 355 510 20
max 0,22 1,6 0,55 0,045 0,045 0,30 0,30
min 0,14 0,5 490 590 18
max 0,21 1,5 0,60 0,050 0,050 0,30 0,30
BS
4449:1997460B
DIN
488:2009
460A
B500A
B500B
MSZ 339-87
STAS
438/1-89
OB 37 1800
- 0,5d
PC 52
Standard ClassChemical composition
SRPS EN10080
1800
- 3d
B 60.50 1800
- 3d
Mechanical properties
Bending
B500A
B500B
5d 16 mm
8d >16 25 mm
10d > 25 mm
4d 16 mm
7d >16 mm
5d 16 mm
8d > 16 28 mm
10d > 28 32 mm
Ceq = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15
Notes:
1) It is allowed to cross over maximal value of C for 0,03% if the value of Ceq is decreased in 0,02 per weight (this refers only for standard BS4449:2005, 1997)
2) Higher content of nitrogen is allowed if sufficient amounts of nitrogen-bending elements are present.
5. Concrete steel is produced in a shape of rebar according to: TP 1-1(Heating the billets inside the furnace), TP 1-2 (Plans of billet input), TP 1-3(Monitoring during rolling), TP 1-4 (Cooling the billets with water using Tempcore technology), TP 1-5 (Cutting, controling and packing). Steel OB 37 is produced
without water cooling.
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
8/10
6. Packing into bundles and marking the bundle
Rebars are tied in steel band into the bundles of 4t or 2,5 t (+/-5%). In these cases, the steelband is used. Its diameters are 0,8 x 31,75 mm and the tension strength is m=1000 N/mm
2.
Each bundle is tied in 5 places in distance od 2,5m and 1m from its end. Soft anneal string isused for lifting the bundle. Diameter of the string is 4 6mm, has 4 connections and thetension strength is m=360 N/mm
2.Also, every bundle has a tagged waterproof label with the
data shown in the table. Label is fill in by a printer.
DESCRIPTION: HOT ROLLED REBAR
NAZIV: TOPLO VALJANE IPKE
PRODUCED IN SERBIA
PROIZVEDENO U SRBIJI
PRODUCER: METALFER STEEL MILL D.O.O.
PROIZVOA: METALFER STEEL MILL D.O.O.
SIZE (MM):
DIMENZIJA (MM):
LENGTH (M):
DUINA (M):
QUALITY:
KVALITET:
BUNDLE NET WEIGHT (KG):
MASA BUNTA NETO (KG):
HEAT No:
ARA Br.:
BUNDLE No.:
BUNT Br.:
PRODUCTION DATE:
DATUM PROIZVODNJE:
SHIFT:
SMENA:
BUYER:
KUPAC:
CONTRACT
UGOVOR Br.
CLASS:
KLASA:
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
9/10
7. DEFECTS OF THE FINAL PRODUCT7.1 Defects of the final product and the identification of the nonconforming product are described
in annex of file KP 1-01/01
DOCUMENT CODE: KP-1-01/01
EDITION: 1 PAGE: 1 of 1
QUALITY MANAGEMENT SYSTEM CONFIDENTIALITY:P.T.
STATUS (COPY NO.):
AUTHOR : Manager of Quality Control Dept. A. Ermolaev CONTROLED BY:Representative of Quality Management A.Ermolaev
APPROVED BY : Deputy of General Manager for production B. Zeevi DATE: 03.09.2008 SUPERIOR DOCUMENT:KP-1-01
LIST OF FINAL PRODUCT DEFECTS
(II CLASS)
DEFECT
CODE
(NUMBER)
TYPE OF DEFECT ALLOWANCE
1 SHORT OR LONG BARS 100 mmOF NOMINAL LENGHT
2 CAMBER
MAXIMUM 0,6%
PER MEASURING LENGHT
(6 mm per 1 meter)
3MECHANICAL PROPERTIES ARE NOT
ACCORDING TO STANDARD
MECHANICAL PROPERTIES MUST
BE ACCORDING TO STANDARDS
4NOMINAL WEIGHT VARIATION PER
METER OF LENGHT
6 % for d8mm SRPS EN 10080 4,5 % (SRPS EN 10080; BS 449;
STAS 438/1-89)+ 6/-4 % DIN 488:2009
4 % MSZ 339
5
BAR SURFACE DOESNT MATCH THESTANDARD (LOW OR HIGH RIB,
RELATIVE SURFACE Fr OF THE RIB IS
NOT SUITABLE)
According to: SRPS EN 10080, BS 4449
Fr 0,040 min. for d12mmFr 0,056 min. for > d12mmAccording to: DIN 488:
Fr 0,045 min. for d8mm
Fr 0,052 min. for d10mm
Fr 0,056 min. for d12mm
6ASPERITY OF BAR SURFACE
(NOT A FINE APPEARANCE)
10 TONS MAX CAN BE DONE TO
THE CHANGE OF CALIBRE
7NOMINAL DIMENSION DEVIATION
(FOR PLAIN BAR)
+0,3/-0,5 mm,
OVALTY - 0,8 mm MAXIMUM
Quality Management System Technician notes second category on scale and the bar defects.
If the bundle is second category, old lable is removed and new one is placed. New label must contain
second category detail and one or more listed defects specified in brackets.
CHANGE NO.: APPROVED BY: DATE CHANGE NO.: APPROVED BY: DATE:1 A. Ermolaev 18.09.2008
2 A. Ermolaev 29.12.2008
3 I. Romandi 09.12.2010
-
7/30/2019 Technical Spec Ts 1-08 Srps en Bs Din Stas i Msz
10/10
Marking of finished bar
Marking of finished bar - Standard MSZ 339-1987