Download - Sic_403 Quality Laboratory Management
-
1
SIC 403: LAB MANAGEMENT AND QUALITY ASSURANCE
LABORATORY PRACTICES AND MANAGEMENT
THE FUNDAMENTAL POINTS OF GOOD LABORATORY PRACTICES
(GLP)
The GLP regulations set out the rules for good practice and help researchers
perform their work in compliance with their own pre-established plans and
standardized procedures.
The regulations are not concerned with the scientific or technical content of
the research programmes. Nor do they aim to evaluate the scientific value of
the studies.
GLP stress importance of the following points five points:
1. Resources: organization, personnel, facilities and equipment
2. Characterization: test items and test systems
3. Rules: study plans (or protocols) and written procedures
4. Results: raw data, final report and archives
5. Quality Assurance.
RESOURCES
This is divided into three parts:
1. Management
2. Personnel
-
2
3. Facilities: buildings and equipment
MANAGEMENT
Without full commitment of management, GLP systems will not function as
they should and will lack credibility. Managerial aspects are therefore
critical for GLP implementation in a laboratory.
Laboratory management responsibilities and organizational requirements
take up about 15% of the GLP text, clearly demonstrating that the regulators
also consider these points as important.
Management has the overall responsibility for the implementation of both
good science and good organization within their institution
Good Science
Careful definition of experimental design and study parameters.
Science based on known scientific principles.
Control and documentation of experimental and environmental variables.
Careful and complete evaluation and reporting of results.
Results becoming part of accepted scientific knowledge.
Good Organization
Proper planning of studies and allocation of resources.
Provision of adequate facilities, infrastructure and qualified staff.
Definition of staff responsibilities and provision of staff training.
-
3
Establishment of procedures to ensure proper conduct of studies.
Good record keeping and organized archives.
Implementation of verification procedures for study conduct and results.
These organizational aspects of studies can be met by complying with GLP.
Management delegates a number of functions to other staff without losing
the overall responsibility for the work.
For each specific study, management must appoint a study director who
takes on the responsibility for the planning and daily conduct of the study
and also the interpretation of study results.
Planning (Master Schedule)
The need for a system of organizing the allocation of resources and time for
studies is self-evident.
GLP requires that Management ensures allocation of sufficient personnel
and other resources to specific studies and support areas.
The record of planning/resource allocation required by GLP is called the
master schedule.
The format of the master schedule is not stipulated. However, the general
rules are:
All studies (contracted and in-house) must be included in the schedule.
A change control procedure is in place to reflect shifts in dates and
-
4
workload.
Time-consuming activities such as protocol review and report preparation
should also be included.
The schedule is official (i.e. there should not be two or more competing
systems for the same purpose).
The system is described in an approved SOP.
Responsibilities for its maintenance and updating are defined by
management.
Various versions of the master schedule are approved and maintained in
the archive as data.
Distribution is adequate and key responsibilities are identified.
Typically, once the protocol is signed and issued, the study is entered into
the master schedule.
Often responsibility for the master schedule rests with project management
and the schedule is computerized for efficiency and ease of cross-indexing.
The master schedule system is described in an SOP.
Typically, QA has read-only and print access to this data file. Signed
hard copies are usually archived as raw data.
In contract facilities, sponsor and test item names are usually coded to
provide confidentiality.
-
5
Archived master schedules are often consulted by inspectors to evaluate
whether or not there were sufficient personnel available during the period of
the study being inspected.
The easy retrieval of historical schedules is therefore important.
PERSONNEL
GLP requires that the overall organization of the test facility be defined. This
is usually done through an organization chart.
This is often the first document requested by inspectors to obtain an idea of
how the facility functions.
Sometimes the organization chart forms part of a quality Manual or other
document that describes the nature of the institution and the way in which it
operates.
These are high level documents. They are supplemented by more detailed
information which may be incorporated into the following documents
relating to each individual:
curriculum vitae
training records
job description.
-
6
Together these three documents meet the GLP requirement that records are
maintained to demonstrate that staff have the competence, education,
experience and training necessary to perform their tasks.
The format and contents of these documents should be defined in SOPs and
verified regularly in QA audits.
Curriculum Vitae (CV)
A procedure should ensure that CVs:
exist for all personnel in a standard approved format;
are kept up-to-date;
exist in required languages
are carefully archived to ensure historical reconstruction.
In a CV it is usual to include:
name and age of the person;
education, including diplomas and qualifications awarded by
recognized institutions;
professional experience earned both within the institution and before
joining it;
any publications (these may be listed separately, if numerous);
membership of associations;
languages spoken.
-
7
All staff should have a CV. Even if some personnel do not have extensive
qualifications, they will have professional experience which should be listed
in their CV. It is good practice to have the CV signed and dated by the
person concerned, to avoid discrepancies in the content.
FACILITIES: BUILDINGS AND EQUIPMENT
Buildings
GLP requires that test facilities be of appropriate size, construction and
location to meet the requirements of the study and minimize disturbances
that would interfere with the validity of the study.
They should be designed to provide an adequate degree of separation
between the various activities of the study.
The purpose of these requirements is to ensure that the study is not
compromised because of inadequate facilities.
It is important to remember that fulfilling the requirements of the study does
not necessarily mean providing state of the art constructions, but carefully
considering the objectives of the study and how to achieve them.
It is up to the facility management to define what is adequate; this will
depend on the kind of studies being performed.
Separation ensures that different functions or activities do not interfere with
each other or affect the study.
-
8
Minimising disturbance by separation can be achieved by:
Physical separation: this can be achieved by walls, doors or filters, or by
the use of isolators. In new buildings or those under transition or
renovation, separation will be part of the design.
Separation by organization, for example by the establishment of defined
work areas within a laboratory carrying out different activities in the
same area at different times, allowing for cleaning and preparation
between operations or maintaining separation of
staff, or by the establishment of defined work areas within a laboratory.
To illustrate the principles involved consider these two examples that are
often found in laboratories. These are (A) The Dose Mixing Unit: the zone
used for the preparation of the dosage form and (B) Animal House Facilities.
Example A: Dose Mixing Unit
The Dose Mixing Unit is a laboratory area dealing with the work flow of test
items, vehicles and control items: receipt, storage, dispensing, weighing,
mixing, dispatch to the animal house and waste disposal.
A.1 - Size
The laboratory must be big enough to accommodate the number of staff
working in it and allow them to carry on their own work without risk of
interfering in each others work or mixing up different materials.
-
9
Each operator should have a workstation sufficiently large to be able to carry
out the operation efficiently. There should be sufficient physical separation
between the workstations to reduce the chance of mix up of materials or
cross contamination.
The dose mixing area is a sensitive zone and access to it should be restricted
so as to limit the possibility of people becoming vectors of pollution or
contamination between studies or test items.
A.2 - Construction
The laboratory should be built of materials that allow easy cleaning and do
not allow any test items to accumulate in corners or cracks and cross
contaminate others.
There should be a proper ventilation system with filters that serve to protect
personnel and prevent cross contamination.
Many modern dose mixing areas are designed in a box fashion, each box
having an independent air handling system.
A.3 - Arrangement
Ideally there should be separate areas for:
storage of test items under different conditions
storage of control items
storage of vehicles
-
10
handling of volatile materials
weighing operations
mixing of different dose forms e.g. diet and liquid
storage of prepared doses
cleaning equipment
offices and refreshment rooms
changing rooms.
Example B: Animal House Facility
To minimize the effects of environmental variables on the animal, the
facility should be designed and operated to control selected parameters (such
as temperature, humidity and light).
In addition, the facility should be organized in a way that prevents the
animals from coming into contact with disease, or with a test item other than
the one under investigation.
Requirements will be different depending upon the nature and duration of
the studies being performed in the facility.
Risks of contamination can be reduced by a barrier system, where all
supplies, staff and services cross the barrier in a controlled way.
A typical animal house should have separations maintained by provision of
areas for:
-
11
different species
different studies
quarantine
changing rooms
receipt of materials
storage of materials
bedding and diet
test doses
cages
cleaning equipment
necropsy
waste disposal.
The building and rooms should provide sufficient space for animals and
studies, allowing the operators to work efficiently.
The environment control system should maintain the temperature, humidity
and airflow constantly at the defined levels for the species concerned.
Design should allow easy and thorough cleaning of surfaces of walls, doors,
floors and ceilings.
There should be no gaps or ledges where dirt and dust can accumulate.
-
12
Water should not accumulate on uneven floors i.e. floors should be smooth
and even and without crevices.
Whatever the capabilities or needs of the laboratory, sensible working procedures
can reduce the damage from outside influences.
Such procedures may include:
minimising the number of staff allowed to enter the building;
restricting entry into animal rooms;
organising work flow so that clean and dirty materials are moved
around the facility at different times of the day and ensuring that
corridors are cleaned between these times;
requiring staff to put on different clothing for different zones within
the animal facility;
ensuring that rooms are cleaned between studies.
Equipment
Suitability and Calibration
To perform a study properly, adequate equipment must be available.
All equipment should be suitable for its intended use.
The equipment that is suitable for a given study depends on the type of the
study and the study objectives.
-
13
Suitability can only be assessed by consideration of the performance of the
equipment. For example, there is no need to have a balance capable of
weighing to decimals of a milligram to obtain the weekly weight of a rat;
however a balance with this precision may be required in the analytical
laboratory.
Defining the suitability of equipment is a scientific problem to be judged by
the study director.
For some equipment it is necessary to conduct formal tests or even formal
qualification to demonstrate that it is fit for its intended use. This is often the
case for analytical equipment.
Whether formally qualified or not, all equipment must be calibrated and
maintained to ensure accurate performance.
Most frequently, the calibration depends on the use of standards used. For
example, in the case of a balance, the standards are the weights that have
been certified by a national or international standards authority as being
within specified limits. Frequently the laboratory will have a set of certified
weights.
These primary standards are only used to qualify secondary standards,
which are then used on a routine basis.
-
14
Another example is standard chemicals which are used to test/calibrate
equipment, like pH meters, to ensure accurate performance. Standards may
also be compound samples of known concentration used to ensure that
analytical equipment is functioning as expected and providing a basis for the
calculation of the final result.
The laboratory must decide the acceptable frequency for calibration; this
will depend on the type of equipment and its use. The calibration programme
should be included in the SOPs of the institution.
Proof that equipment is performing to specifications is essential, whether
generating data (e.g. analytical equipment or balances) or maintaining
standard conditions (e.g. refrigerators or air conditioning equipment). This
can be done by periodic checking at a frequency that allows action to be
taken in time to prevent any adverse effect on the study should the
equipment be faulty.
Logbooks are often used to record these regular verifications.
Full documentation of all tests for suitability and for all calibration must be
kept within the laboratory to allow scientists to assess the accuracy of
measurements taken during studies. These data should be archived so that
they are readily available should it become necessary to investigate the
results of a study, or during regulatory inspections.
-
15
Records of repairs and routine maintenance, and any non-routine work
should be kept.
Note: The purpose of these GLP requirements is to ensure the reliability of data
generated and to ensure that data are not lost as a result of inaccurate, inadequate
or faulty equipment.
Maintenance
Facilities - Buildings and Equipment
GLP requirements that equipment should be maintained are based on the
assumption that this reduces the likelihood of an unexpected breakdown and
consequent loss of data.
Maintenance may be carried out in two distinct ways:
preventive or planned, whereby a regular check is made irrespective of
the performance of the equipment;
curative or reparative, when the piece of equipment is not functioning
according to specification or when the equipment or system has broken
down.
Planned routine maintenance is a useful precaution for equipment that does
not have a suitable backup or alternative. However, some pieces of
equipment, such as moderncomputer driven analysers or electronic balances,
do not lend themselves to routine maintenance.
-
16
A better approach may be to check them regularly and ensure that suitable
contingencies are available if any problem occurs. The contingencies may
include having duplicate equipment, having immediate access to an
engineer, or having immediate access to a contract laboratory with
equivalent equipment.
Back-up for vital equipment as well as back-up for power failure should be
available whenever possible. A laboratory should have the ability to
continue with essential services to prevent the loss of animals or data. For
example, a laboratory carrying out animal studies may need a stand-by
generator capable of maintaining at least the animal room environment to
prevent the loss of the animals that would irretrievably affect the study.
Meanwhile, samples could be stored for a period until power is restored.
Early warning that equipment is malfunctioning is important. Periodic
checks will help detect malfunction, but this may also be achieved with
alarms, particularly if the problem occurs at a time when staff are not present
in the laboratory.
Routine maintenance requires planning and this should be indicated in a
service plan.
-
17
There are no specific rules concerning the format of the plan. Like all
planned events the service plan should clearly indicate what is to be done
and when.
The related SOP should indicate tolerances for the targeted dates, how the
actions are to be recorded and, of course, who is responsible for maintaining
the plan.
When equipment is serviced, this should be recorded so that tracing back to
this service (even many months or years after the event) is possible. It is a
good idea to label serviced equipment to indicate when it was last serviced
and when the next service is due. This makes it easy for staff using the
equipment to assess whether or not the service is overdue.
Equipment should not be used without maintenance cover.
There should also be documents recounting the breakdown or problems
encountered with equipment. Each time a service, check or repair action is
undertaken this should be recorded, identifying the person performing the
work, the type and nature of work done and the date. Such documentation is
frequently called a fault action report.
The history of the fault and how it has been handled, including the outcome
of repair work etc., should be clearly indicated. This applies equally whether
-
18
the action is taken by an in-house person or by someone who is brought in
for a specific task (e.g. a contractor for calibration, repair or qualification).
Documentation
Facilities Buildings and Equipment
Staff must be sure that that the equipment they use is suitable for use, has
been adequately calibrated and maintained and is not outside its service
interval.
Records of equipment suitability, calibration, checking and maintenance
demonstrate that the laboratory SOPs have been followed and that the
equipment used in any study is adequate for the job and performing to its
specification.
Records should also demonstrate that required actions have been taken as a
result of the checks made. Documents and records should also show that that
staff are well instructed in the use of equipment and are able to take
appropriate action when problems arise.
The following is a list of documents that should be present in a GLP compliant
institution:
1. SOP: SOPs for instructions in the routine use, cleaning, calibration etc. of
the facility or equipment. SOP for the regular verifications or services
performed on buildings or equipment.
-
19
2. Qualification documents: When formal qualification is required, each
phase of the qualification process should be documented. Each phase should
have a protocol defining the tests to be conducted, data resulting from these
tests, a report including the test results and a conclusion. When no formal
qualification is required, the study director or the management of the
institution should define, usually in an SOP, the purpose of the equipment.
For example, a balance with a precision to the nearest gram will be suitable
for weighing in an animal house but not in the analytical laboratory.
3. Logbook: Logbooks are kept to record the use of equipment (e.g. HPLC
column used for product x with dates, then for product y with dates).
They are also used for recording regular checks (e.g. regular use of check-
weight for balances, temperature record for refrigerator, etc.).
4. Service report: Service reports and equipment labels indicate which
instrument was serviced, when and by whom. The date of the next service is
usually recorded on the equipment label. In the case of routine servicing the
actual service procedure would be included in the SOP concerning the
apparatus or facility.
5. Fault action report: These reports are made when something goes wrong.
This is not routine work and an SOP may not be available for the person
who deals with this problem. Therefore the fault action report should include
-
20
the work performed on the equipment, the date of the work and the person
who carried out the job. It is important that the person signs off with a
statement indicating whether the equipment is fit or unfit for use.