Research ArticleSelection of Microstrip Patch Antenna Substrate for WLANApplication Using Multiple Attribute Decision Making Approach
Navneet Gupta and Rituraj Raman
Department of Electrical and Electronics Engineering, Birla Institute of Technology and Science, Pilani, Rajasthan 333031, India
Correspondence should be addressed to Navneet Gupta; [email protected]
Received 30 June 2014; Accepted 7 October 2014; Published 22 October 2014
Academic Editor: Giancarlo Bartolucci
Copyright Β© 2014 N. Gupta and R. Raman. This is an open access article distributed under the Creative Commons AttributionLicense, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properlycited.
This paper presents a material selection approach for selecting microstrip patch antenna substrate for WLAN applications usingmultiple attribute decisionmaking (MADM) approach. In this paper, differentmicrowave dielectricmaterials for substrate and theirproperties like relative permittivity, quality factor, and temperature coefficient of the resonant frequency are taken into considerationand MADM approach is applied to select the best material for microstrip patch antenna. It is observed that Pb
0.6Ca0.4ZrO3is the
best material for the antenna substrate in MPA for WLAN applications. It was observed that the proposed result is in accordancewith the experimental finding thus justifying the validity of the proposed study.
1. Introduction
Due to increase in variety of mobile communication equip-ment, such as laptops, personal digital assistants, smart-phones, and wireless modems, the demand for adaptableand functional miniature antennas are growing very fast [1].A wireless local area network (WLAN) links two or moredevices using some wireless distribution method (typicallyspread-spectrum or OFDM radio) and usually providing aconnection through an access point to the wider internet.This gives users the mobility to move around within a localcoverage area and still be connected to the network [2,3]. To achieve this, microstrip patch antennas (MPAs) playan important role and are good candidates for wide-bandapplications.
Material selection forMPA in general anddielectricmate-rials for its substrate in particular are complicated as thereare a number of materials that have been proposed; however,each of these materials has certain merits and limitations.The key performance indices for MPA substrate are relativepermittivity, quality factor, and temperature coefficient ofthe resonant frequency. This paper discusses a strategy forselecting suitable material for substrate based on multipleattribute decision making (MADM) approach [4] in order toimprove the antenna performance.
This paper is organized as follows. Section 2 explainsthe microstrip patch antenna design. Section 3 explains theselection criteria of materials.This section describes the deci-sion making approach and details of technique for orderpreference by similarity to ideal solution (TOPSIS), whileSection 4 includes the application of TOPSIS method toantenna substrate material selection in MPAs. Section 5 pre-sents the conclusions drawn from this study.
2. Microstrip Patch Antenna Design
Schematic view of microstrip patch antenna (MPA) is shownin Figure 1. The patch and the ground plane are separatedby a dielectric substrate. For WLAN application the size ofantenna should be small. In order to reduce the size of theantenna, substrate with high dielectric constants must beused. However, this may cause the increase in the cost ofmaterial and the frequency shift due to the material toleranceand result in narrowing of the operating bandwidth. So, thedesign of the antenna patch also plays an important role.
Dielectric substrate materials used in patch antennasinclude ceramic, semiconductor, ferromagnetic, synthetic,composite, and foams. The properties of substrate materialscommonly studied while designing the patch antennas are
Hindawi Publishing CorporationInternational Journal of Microwave Science and TechnologyVolume 2014, Article ID 703181, 5 pageshttp://dx.doi.org/10.1155/2014/703181
2 International Journal of Microwave Science and Technology
Dielectric substrate
Microstrippatch
Microstriptransmission
line
πr
L
W
Figure 1: The basic structure of microstrip patch antenna (MPA).
permittivity (ππ), quality factor (π-factor), and temperature
coefficient of the resonant frequency (ππ).
Certain other properties sintering temperature, thermalproperties, and chemical compatibility are also consideredwhile dealing with the fabrication aspects.
For antenna in WLAN routers the desirable propertiesare low permittivity, high quality factor, low temperaturecoefficient of resonance, and low cost. This is because lowpermittivity allows larger bandwidth and a high quality factorprovides better selectivity and is also responsible for strongresonance and high frequency stability. The variation ofresonant frequency with temperature is undesirable, so theabsolute value of this parameter should be as low as possible.If we are going for mass production of such antennas thencost should be as low as possible.
3. Multiple Attribute DecisionMaking Approach
MCDM (multiple criteria decision making) methods can beused to solve uncertainty problems.Multiple criteria decisionmaking (MCDM) can be broadly divided into
(i) multiobjective decision making (MODM);(ii) multiattribute decision making (MADM).
MODM is optimization of an alternative or alternativeson the bases of prioritized objectives.
MADM is selection of an alternative from a set of alter-natives based on prioritized attributes of the alternatives.
MODM studies decision problems in which the decisionspace is continuous and design alternatives are defined implic-itly by a mathematical programming structure (a typical exam-ple is mathematical programming problems with multipleobjective functions).
On the other hand, MADM concentrates on problemswith discrete decision spaces and alternatives are definedexplicitly by a finite list of attributes. In these problems the setof decision alternatives has been predetermined. Moreover,an attribute with a direction may be an objective. Differenttypes of methods are developed based on MADM approach.For the present work, we adopted the TOPSIS method to find
the best alternative [4]. TOPSIS stands for technique for orderpreference by similarity to ideal solution. This is based on theidea that the chosen alternative should be nearer to the idealsolution and away from the negative-ideal solution in somegeometrical sense.
The TOPSIS method takes the following steps.
Step 1 (construct the normalized decision matrix). The valueof each criterion is normalized to 1. The characteristics π Γπ (GHz) π
π, ππ(ppm/βC), and base material cost ($/g) are
considered for criterion with higher benefits in higher value;each value is divided by the highest value. For criterion withhigher benefits in lower value, each value is divided by thehighest value, giving the highest value a value of 1, and thenthese values are subtracted from 1. So we get the normalizeddecision matrix π .
Step 2 (construct the weighted normalized decision matrix).With the set ofweightsπ = (π€
1, π€2, π€3, . . . , π€
π) theweighted
normalized matrix π can be generated as follows:
π = π π =
[
[
[
[
[
[
π€1β π11
π€2β π12β β β π€
πβ π1π
π€1β π21
π€2β π22β β β π€
πβ π2π
β β β β β β
β β β β β β
π€1β ππ1
π€2β ππ2
β β β π€πβ πππ
]
]
]
]
]
]
, (1)
where βπβ is the number of alternatives and βπβ is the numberof criteria.
Step 3 (determine the ideal and negative-ideal solutions). Theideal solutionπ΄β and the negative-ideal solution, denoted byπ΄β, are
π΄β= {(max V
ππ| π β π½
1) , (max V
ππ| π β π½
2) ,
π = 1, 2, 3, . . . , π}
= {Vβ1, Vβ2, . . . , Vβ
π}
π΄β= {(min V
ππ| π β π½
1) , (min V
ππ| π β π½
2) ,
π = 1, 2, 3, . . . , π}
= {V1
β, V2
β, . . . , V
π
β} .
(2)
In (2), π½1= {π = 1, 2, 3, . . . , π and π is associated with benefit
criteria}, π½2= {π = 1, 2, 3, . . . , π and π is associated with cost
criteria}.Therefore, it is obvious that the previous created alterna-
tivesπ΄β andπ΄β represent themost preferable alternative, thatis, the ideal solution, and the least preferable alternative or thenegative-ideal solution, respectively.
Step 4 (calculate the separation measure). Next the separa-tion distances of each alternative from the ideal solution andthe negative-ideal solution are reached by the π-dimensionalEuclidean distance method. That means πβ
πis the distance
International Journal of Microwave Science and Technology 3
Table 1: Characteristics parameters of selected materials [5β13].
S. number Substrate material ππ
π Γ π (GHz) ππ(ppm/βC) Base material cost ($/g)
A 0.9(Zr0.8Sn0.2)TiO4 + 0.1MgCO3 38.9 4000 β2.3 6.32B La0.4Ba0.6Ti0.6Yb0.4O3 65 4500 1 0.148C 0.58ZnNb2O6-0.42TiO2 45 6000 0 0.132D Ca0.4(L1/2Nd1/2)0.6TiO3 113 5000 8 0.172E Pb0.6Ca0.4ZrO3 94 3600 β10 0.16F BaO-PbO-Nd2O5-TiO2 88 5000 0 0.148G Pb0.45Ca0.55(Fe1/2Nb1/2)O3 93 6000 2 0.144H Ba4.2(Sm0.8Nd0.2)9.2Ti18O54 84 9000 0 0.132I (Ba0.8Sr0.2)4.2Sm9.2Ti18O54 82.3 2860 0.4 0.132J (Ba0.95Ca0.05)O-Sm2O3-4.5TiO2 81 9500 2 0.132
(in an Euclidean sense) of each alternative from the idealsolution and is defined as
πβ
π= β
π
β
π=1
(Vππβ Vβπ)
2
for π = 1, 2, 3, . . . , π (3)
and the distance from the negative-ideal solution is definedas follows:
ππ
β= β
π
β
π=1
(Vππβ Vπβ)
2
for π = 1, 2, 3, . . . , π. (4)
Here, Vβπand Vπ
β are the values of the best and the worst alter-native in a particular criteria βπ.β
Step 5 (calculate the relative closeness to the ideal solution).The relative closeness of an alternative π΄
πwith respect to the
ideal solution π΄β is represented by
πΆπ=
πβ
π
πβ
π+ ππ
β, (5)
where 0 < πΆβπ< 1 and π = 1, 2, 3, . . . , π.
Apparently an alternativeπ΄πis closer to the ideal solution
as πΆβπapproaches 1.
Thus, πΆβπ= 1, if π΄
π= π΄β, and πΆ
π
β= 0, if π΄
π= π΄β.
Step 6 (rank the preference order). Now a preference ordercan be ranked according to the order of πΆβ
π. Therefore, the
best alternative is the one nearer to the ideal solution andaway from the negative-ideal solution.
The labels proposed for the weighting are the following:
π = {Essential, Very High, Fairly High, High, Moderate,
Low, Fairly Low, Very Low, Unnecessary} .(6)
4. Result and Discussion
Various properties of different possible materials for patchantenna substrate suitable for WLAN applications are tabu-lated and shown in Table 1.
The normalized matrix π is
π =
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
0.66 0.42 0.77 0
0.42 0.47 0.9 0.976582
0.6 0.63 1 0.979114
0 0.53 0.2 0.972785
0.17 0.38 0 0.974684
0.22 0.53 1 0.976582
0.18 0.63 0.8 0.977215
0.26 0.95 1 0.979114
0.27 0.3 0.96 0.979114
0.28 1 0.8 0.979114
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
. (7)
Highest value of weight is given to that parameter which ismore essential, in this case it is π
πand least value is given to
the parameter which is not that much important. Hence theweighted matrixπ is
π = [0.4 0.3 0.2 0.1] . (8)
The weighted normalized matrix π is
π =
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
0.264 0.126 0.154 0
0.168 0.141 0.18 0.097658
0.24 0.189 0.2 0.097911
0 0.159 0.04 0.097278
0.068 0.114 0 0.097468
0.088 0.159 0.2 0.097658
0.072 0.189 0.16 0.097721
0.104 0.285 0.2 0.097911
0.108 0.09 0.192 0.097911
0.112 0.3 0.16 0.097911
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
. (9)
In this, ideal and nonideal solutions are as follows:
ideal: 0.264 0.3 0.2 0.097911 ;
nonideal: 0 0.09 0 0 .
4 International Journal of Microwave Science and Technology
Table 2: Solution of study based on TOPSIS method.
S. number Substrate material πΆπ
RanksA 0.9(Zr0.8Sn0.2)TiO4 + 0.1MgCO3 0.399675 7B La0.4Ba0.6Ti0.6Yb0.4O3 0.40917 6C 0.58ZnNb2O6-0.42TiO2 0.249265 10D Ca0.4(L1/2Nd1/2)0.6TiO3 0.729575 2E Pb0.6Ca0.4ZrO3 0.734938 1F BaO-PbO-Nd2O5-TiO2 0.475171 5G Pb0.45Ca0.55(Fe1/2Nb1/2)O3 0.501612 4H Ba4.2(Sm0.8Nd0.2)9.2Ti18O54 0.338723 9I (Ba0.8Sr0.2)4.2Sm9.2Ti18O54 0.52054 3J (Ba0.95Ca0.05)O-Sm2O3-4.5TiO2 0.341528 8
From theweightednormalizedmatrix, the value of separationvariables was found out to be
πβ
1= 0.204887, π
1
β= 0.307747
πβ
1= 0.186808, π
1
β= 0.269745
πβ
1= 0.113565, π
1
β= 0.342035
πβ
1= 0.339378, π
1
β= 0.125794
πβ
1= 0.336173, π
1
β= 0.121244
πβ
1= 0.225515, π
1
β= 0.249083
πβ
1= 0.225355, π
1
β= 0.223907
πβ
1= 0.160702, π
1
β= 0.313732
πβ
1= 0.261725, π
1
β= 0.24107
πβ
1= 0.157175, π
1
β= 0.303036.
(10)
Now we can calculate the ideal solution from the following:
πΆπ=
πβ
π
πβ
π+ ππ
β. (11)
So the ideal solutions are given in Table 2. The ranks aregiven based on their βπΆβ values. The material with highestπΆ value was given the best rank. So from these ranks wecan say that, out of the selected materials, Pb
0.6Ca0.4ZrO3
was found to be the best material for the substrate ofmicrostrip patch antenna for WLAN application followedby Ba
4.2(Sm0.8Nd0.2)9.2Ti18O54
and (Ba0.95
Ca0.05
)O-Sm2O3-
4.5TiO2.
The outcome of this study is compared with the patentfiled by Killen and his coinventors [14] and it is observedthat using this material best performance of the antennawith miniaturized size can be obtained which is required forWLAN application. So this validates our study of dielectricsubstrate ceramic material for microstrip patch antenna.
5. Conclusion
This paper presented thematerial selection for themicrostrippatch antenna substrate for WLAN applications using mul-tiple attribute decision making (MADM) approach usingtechnique for order preference by similarity to ideal solution(TOPSIS). It was observed that Pb
0.6Ca0.4ZrO3is the best
material for the antenna substrate for WLAN applicationsfollowed by Ba
4.2(Sm0.8Nd0.2)9.2Ti18O54and (Ba
0.95Ca0.05
)O-Sm2O3-4.5TiO
2. This finding is also in agreement with the
experimental results which justify the validity of the proposedstudy.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
References
[1] S. C. Basaran and Y. E. Erdemli, βA dual-band split-ringmonop-ole antenna for WLAN applications,β Microwave and OpticalTechnology Letters, vol. 51, no. 11, pp. 2685β2688, 2009.
[2] C.-Y. Pan, C.-H. Huang, and T.-S. Horng, βA new printed G-shaped monopole antenna for dual-band WLAN applications,βMicrowave and Optical Technology Letters, vol. 45, no. 4, pp.295β297, 2005.
[3] R. Zaker, C. Ghobadi, and J. Nourinia, βA modified microstrip-fed two-step tapered monopole antenna for UWB and WLANapplications,β Progress in Electromagnetics Research, vol. 77, pp.137β148, 2007.
[4] N. Gupta, βMaterial selection for thin-film solar cells usingmul-tiple attribute decisionmaking approach,βMaterials andDesign,vol. 32, no. 3, pp. 1667β1671, 2011.
[5] D. J. Kim, J. W. Hahn, G. P. Han, S. S. Lee, and T. G. Choy,βEffects of alkaline-earth-metal addition on the sinterability andmicrowave characteristics of (Zr,Sn)TiO
4dielectrics,β Journal of
the American Ceramic Society, vol. 83, no. 4, pp. 1010β1012, 2000.[6] A. Feteira, R. Elsebrock, A. Dias, R. L. Moreira, M. T. Lana-
gan, and D. C. Sinclair, βSynthesis and characterisation ofLa0.4Ba0.6Ti0.6RE0.4O3(where RE = Y, Yb) ceramics,β Journal of
the European Ceramic Society, vol. 26, no. 10-11, pp. 1947β1951,2006.
International Journal of Microwave Science and Technology 5
[7] D.-W. Kim, D.-Y. Kim, and K. S. Hong, βPhase relations andmicrowave dielectric properties of ZnNb
2O6-TiO2,β Journal of
Materials Research, vol. 15, no. 6, pp. 1331β1335, 2000.[8] J. Kato, H. Kagata, and K. Nishimoto, βDielectric properties of
(PbCa)(MeNb)O3at microwave frequencies,β Japanese Journal
of Applied Physics. Part 1: Regular Papers and Short Notes andReview Papers, vol. 31, no. 9, pp. 3144β3147, 1992.
[9] K. Wakino, K. Minai, and H. Tamura, βMicrowave characteris-tics of (Zr, Sn)TiO
4and BaOβNd
2O3βTiO
2dielectric resona-
tors,β Journal of the American Ceramic Society, vol. 67, no. 4, pp.278β281, 1984.
[10] E. S. Kim, J. S. Jeon, and K. H. Yoon, βEffect of sin-tering method on the microwave dielectric properties of(Pb0.45
Ca0.55
)(Fe0.5Nb0.5) O3ceramics,β Journal of the European
Ceramic Society, vol. 23, no. 14, pp. 2583β2587, 2003.[11] Y. Li and X. M. Chen, βEffects of sintering conditions
on microstructures and microwave dielectric properties ofBa6β3π₯(Sm1βπ¦Ndπ¦)8+2π₯Ti18O54 ceramics (π₯ = 2/3),β Journal of
the European Ceramic Society, vol. 22, pp. 715β719, 2002.[12] M. Imaeda, K. Ito, M. Mizuta, H. Ohsato, S. Nishigaki, and
T.Okuda, βMicrowave dielectric properties of Ba6β3π₯
Sm8+2π₯
Ti18O54
solid solutions with Sr substituted for Ba,β Japanese Journal ofApplied Physics, vol. 36, no. 9, pp. 6012β6015, 1997.
[13] A.G. Belous andO.V.Ovchar, βMWdielectricswith perovskite-like structure based on Sm-containing systems,β Journal of theEuropean Ceramic Society, vol. 19, no. 6-7, pp. 1119β1122, 1999.
[14] W. D. Killen, R. T Pike, and H. J. Delgado, βHigh efficiency slotfedmicrostrip antenna having an improved stub,βUS Patent, US6791496B1; 2004 , http://www.google.co.in/patents/US6791496.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of