REDES DE AREA LOCAL
DOCENTE: LIC. RUBICEL PINEDA TELLEZ
ALUMNO: ROMAN GUTIERREZ SOSA
GRUPO: B
CUATRIMESTRE: 2
CARRERA:
EVALUACION 2DO PARCIAL
EIGRP.
Es un protocolo de encaminamiento hibrido, ofrece lo mejor de algoritmos de vector de
distancias y del estado enlace. Fue desarrollado por cisco systems en el año de 1986. Se
considera un protocolo avanzado que se basa en las características normalmente
asociadas con los protocolos del estado de enlace. Es un protocolo fácil de configurar, el
cual mejora las propiedades de convergencia.
En esta práctica se va a poner un ejemplo de cómo se configura el protocolo eigrp,
tomando en cuenta la siguiente topología:
Lo primero que haremos es abrir el Packet Tracer y diseñar el esquema, después
continuamos con la configuración de los routers y servidores.
Configuracion Router 1.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname sky
sky(config)#interface serial 0/0
sky(config-if)#ip address 140.0.0.1 255.255.255.252
sky(config-if)#clock rate 56000
sky(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
sky(config-if)#exit
sky(config)#interface serial 0/1
sky(config-if)#ip address 140.0.0.10 255.255.255.252
sky(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/1, changed state to down
sky(config-if)#exit
sky(config)#interface fa 0/0
sky(config-if)#ip address 140.0.0.17 255.255.255.240
sky(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up
sky(config-if)#exit
sky(config)#router eigrp 100
sky(config-router)#network 140.0.0.16
sky(config-router)#network 140.0.0.8
sky(config-router)#network 140.0.0.0
sky(config-router)#exit
sky(config)#enable secret class
sky(config)#enable password cisco
sky(config)#line console 0
sky(config-line)#password cisco
sky(config-line)#login
sky(config-line)#exit
sky(config)#line vty 0 4
sky(config-line)#password cisco
sky(config-line)#login
sky(config-line)#exit
sky(config)#exit
sky#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
sky#disable
sky>
Configuracion Router 2.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#interface serial 0/0
R2(config-if)#ip address 140.0.0.5 255.255.255.252
R2(config-if)#clock rate 56000
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
R2(config-if)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip address 140.0.0.2 255.255.255.252
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/1, changed state to up
R2(config-if)#exit
R2(config)#interface
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up
serial 0/2
R2(config-if)#ip address 140.0.0.13 255.255.255.252
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/2, changed state to down
R2(config-if)#exit
R2(config)#interface fa 0/0
R2(config-if)#ip address 140.0.2.1 255.255.254.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up
R2(config-if)#exit
R2(config)#router eigrp 100
R2(config-router)#network 140.0.0.0
R2(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 140.0.0.1 (Serial0/1) is up: new
adjacency
network 140.0.0.4
R2(config-router)#network 140.0.2.0
R2(config-router)#exit
R2(config)#enable secret class
R2(config)#enable password cisco
R2(config)#line console 0
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#line vty 0 4
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
R2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R2#disable
R2>
Configuracion Router 3.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface serial 0/0
R3(config-if)#ip address 140.0.0.9 255.255.255.252
R3(config-if)#clock rate 56000
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
R3(config-if)#exit
R3(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
interface serial 0/1
R3(config-if)#ip address 140.0.0.6 255.255.255.252
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/1, changed state to up
R3(config-if)#e
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up
xit
R3(config)#interface fa 0/0
R3(config-if)#ip address 140.0.0.33 255.255.255.240
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up
R3(config-if)#exit
R3(config)#router eigrp 100
R3(config-router)#network 140.0.0.4
R3(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 140.0.0.10 (Serial0/0) is up: new
adjacency
%DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 140.0.0.5 (Serial0/1) is up: new
adjacency
network 140.0.0.8
R3(config-router)#network 140.0.0.32
R3(config-router)#exit
R3(config)#enable secret class
R3(config)#enable password cisco
R3(config)#line console 0
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#line vty 0 4
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#exit
R1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R1#disable
R3>
Configuracion Router 4.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R4
R4(config)#interface serial 0/0
R4(config-if)#ip address 140.0.0.14 255.255.255.252
R4(config-if)#clock rate 56000
R4(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
R4(config-if)#exit
R4(config)#interface fa 0/0
R4(config-if)#ip address 140.0.0.129 255.255.255.128
R4(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up
R4(config-if)#exit
R4(config)#router eigrp 500
R4(config-router)#network 140.0.0.12
R4(config-router)#network 140.0.0.128
R4(config-router)#exit
R4(config)#enable secret class
R4(config)#enable password cisco
R4(config)#line console 0
R4(config-line)#password cisco
R4(config-line)#login
R4(config-line)#exit
R4(config)#line vty 0 4
R4(config-line)#password cisco
R4(config-line)#login
R4(config-line)#exit
R4(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
R4#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R4#disable
R4>
Historia de EIGRP.
Es un protocolo de encaminamiento hibrido, ofrece lo mejor de algoritmos de vector de distancias
y del estado enlace. Fue desarrollado por cisco systems en el año de 1986. Se considera un
protocolo avanzado que se basa en las características normalmente asociadas con los protocolos del
estado de enlace. Es un protocolo fácil de configurar, el cual mejora las propiedades de
convergencia.
Elementos de los que se apoya para elaborar sus tablas de enrutamiento:
-Árbol topológico.
-Base de datos topológica.
-Dual.
-LSA.
-LSU.
-IS-IS.
-Hello.
-OSPF.
Proceso que sigue para generar las tablas de enrutamiento y como se involucran cada uno
de los elementos.
-Árbol topológico: Es un conjunto de routers que actúan en coordinación.
-Base de datos topológica: Se encarga de guardar todos los datos en uso dentro de dicha red.
-Dual: Es un algoritmo para la actualización de rutas.
-LSA: Función de filtrado que extiende la capacidad de un ABR que ejecuta el protocolo OSPF.
-LSU: Un paquete de actualización de estado que vínculos, puede contener vario LSA.
-IS-IS: Protocolo de enrutamiento interior de link-state.
-Hello: Se define como una conversación entre iguales, como se comunican los routers.
-OSPF: Protocolo de enrutamiento interior de link-state.
Los Sistemas Autónomos y el rango disponible para numerarlos.
Sistema autónomo: Es un conjunto de redes y dispositivos Router ip que se encuentran por
una sola entidad y que cuentan con una política común de definición de trayectorias para
internet.
Comandos para configurar este protocolo de enrutamiento.
#configure terminal
#router eigrp 10
#network 172.16.3.128
#network 172.16.3.140
#network 172.16.3.136
#CTRL+Z
Comandos para verificar este protocolo de enrutamiento.
#show ip route; muestra la tabla de enrutamiento. #show ip route eigrp; muestra únicamente las entradas EIGRP en la tabla de enrutamiento. #show ip eigrp neightbors; muestra todos los “vecinos” EIGRP. #show ip eigrp topology; muestra todas las entradas EIGRP.