Quick ReferenceTable of Contents:
Pages
E_ Product dimensions
[_ Cutout dimensions
E_ Before you start
[_ Electrical requirements
[_] Installation steps
If you need assistance:
Check your Use and Care Guide for atoll-free number to call or callthe dealer from whom you purchased this appliance. The dealer isristed in the Yerlow Pages of your phone directory under"Appliances -- HousehoMd-- Major -- Service and Repair,"
Call when you:
Have questions about built-in oven installation or operation.Need to obtain the name and number of an authorized servicecompany.
When you call, you will need:
D The builbin oven model number.The built-in oven serial number.
Both numbers are listed on the model/serial rating plate, located onthe oven door or on the oven frame.
27=1/2"recessedheight
Single oven
25=3/8" max.recessed
width
\
29"max_overall
height
27=3/4"min.cutout
height
27"min, ___cabinet width
-1=1/2" min.top of cutoutto underside
of ceuntertep
_
25-1/2"cutout width 5=I/4" bottom of
cutout to f_oer
Single ovenundercounter{without cooktopinstalled above)
T27=3/4"
min.cutoutheight
1=I/2"min,
bottom ofcutout to
top ofcabinet
door
27" min,cabinet width
25=1/2"_--- cutout ---:_
width
1" top of cutoutto bottom of
upper cabinetdoor
t32"
bottom of
cutout tofloor
Single oven
Double oven
25=3/e"max.
recessed width
49-1/2"recessed
height
26=314"
j-
61" max,
overs[[
height
r_J
49-3/4"min,
cutout
height
1=1/2" min,bottom of
cutout to top ofcabinet door
27" ram._--- cabinet --_
I [
25=1/2"_--- cutout --_
width
Double oven
1" top 01 cutoutto bottom of
upper cabinetdoor
14=3/4"bottom
of cutoutto fleer
cabinet -_
2e=li4"mimcutout depth
23"recessed
oven depth
recessed
oven
ovenJ'_ front
Cabinet side view
Your safety and the safety of others arevery imp0rtaet.
We have provided many important safetymessagesin this manualand on your appliance,Atwaye read and obey aHsafety messages=
This is the safety alert symbol.
Thissymboi alertsyou to potentiai hazardsthat can kiii or hurt you and others.
Ati safety messageswiii foiiow the safetyalertsymbol andeither the word "DANGER"or"WARNING".Thesewords mean:
You can be killed or seri0usly injured if you don'tfollow instructions.
Ati safety messageswiii teli you what the potentialhazardis, tell you howto reducethe chance ofinjury, andteti you what can happenif theinstructions are not followed.
important: Observe ali governing codesand ordinances.
Proper installation is your responsibility.Have a qualified technician install this oven.
Oven location should be away from strong draftareas, such as windows, doors and strongheating vents.
Cabinet opening dimensions that are shownmust be used. Given dimensions provideminimum clearance.
Recessed installation area must providecomplete enclosure around the recessed portionof the oven.
Electrical ground is required. See "Electricalrequirements."
Electrical supply junction box should be located3 inches maximum below the support surfacewhen oven is installed in a wall cabinet. Drill a1°inch minimum diameter hole in the right rearor left rear corner of the support surface to passthe appliance cable through to the junction box.For undercounter installation, it is recommendedthat the junction box be located in the adjacentright or left cabinet. If installing the junction boxon rear wall behind oven, junction box must berecessed and located in the upper or lower rightor left corner of cabinet.
Oven support surface MUST be solid, [eve[ andflush with bottom of cabinet cutout.
it is the customer's responsibility:
To contact a qualified electrical installer.To assure that the electrical installation isadequate and in conformance with NationalElectrical Code, AN81/NFPA 70 E latest edition*,and nit local codes and ordinances.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Battervmamh Park
Quincy, Massachusetts 02269
Tool needed:
Sscrewdriver
Parts supplied:
4 screws (double oven)
Page 1
ff codes permit and a separate grounding wire isused, it is recommended that a qualified electriciandetermine that the grounding path and wire gaugeare in accordance with bca[ codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are notsure oven is properly grounded.
Do Not have a fuse in the neutra[ or groundingcircuit.
Oven must be connected to the proper eUectdca[voUtageand frequency as specified on themodeU/sedd rating pUate.(The model/serial ratingplate is located on the oven door or on the ovenframe.}
[_ Models rated from 7.3 to 9.6 kW at 240 volts(5.5 to 7.2 kW at 208 volts} require a separate@°ampere circuit. Models rated at 7.2 kW andbelow at 240 volts (5.4 kW and below at 208volts} require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker isrecommended.
[_ Connect directly to the fused disconnect (orcircuit breaker box} through flexible, armoredor non-metallic sheathed, copper cable (withgrounding wire}.
[_ Flexible armored cable from appliance shouldbe connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must beprovided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with therating of the appliance and to the requirements ofthe National Electrical Code, ANSI/NFPA 70 -- latestedition (% See Page 1) and all local codes andordinances.
if the house has aluminum wiring, follow theprocedure below.
a.) Connect the aluminum wiring to the copper wireusing special connectors designed andUnderwriters Laboratories-listed for joiningcopper to aluminum. Follow the electricalconnector manufacturer's recommendedprocedure.
b.} Aluminum/copper connection must conformwith local codes and industry-accepted wiringpractice.
oven,
|
powersupplycable
I Check oven_ operation.
CC::S:::::::3cUse screws to attachoven to cabinet.
Reattach sidetrim.
Removetrim screws.
Remove sidetrim,
Grasp oven
frame to liftoven.
Use screws toattach oven tocabinet.
Reattach sidetrim,
Remove sidetrim,
shippingfeet,
Replacoven door.
Preparation
Excessive Weight Hazard
Use two or more people to move andinstall oven.Failure to foitow this instruction canresult in back or other injury.
Important: Use both hands to remove ovendoors.
Do Not use handb or any portion of the frontframe or trim for lifting.Before moving oven across floor, check that ovenis on shipping base or slide oven onto cardboardor hardboard.
Do Not remove shipping feet at the front towercorners of oven.
shipping feet.
m Turn power supply off. Move oven close tofinal position.
Remove and discard shipping materials, tapeand protective film from the oven. Do Notremove shipping base or shipping feet at thefront bwer corners of oven. The shipping feetwill protect the [ower oven trim until oven isinserted into cabinet.
, Remove and set aside racks and other partsfrom inside oven.
Remove
oven door.
_ power \
supply cable X
W#_ Remove_ shipping
feet.
Remove trimScrews.
Remove
oven doors.
match on the hinge
in locked position =
door free to openand c[ose
latch on the hinge
position = doorready for removal
Removetrim screw.Pu[[trim out./
Pull top of trimdown.
m Completely open oven door. In both backcorners of the door you will see door latches in thelocked position. Rotate both latches forward to theunlocked position.
Grasp outside edges of door with both hands.• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.. Set door aside on a protective surface.
3m Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end oftrim and puil away from oven. Slide top end oftrim downward to remove trim from oven. Takecare not to scratch other surfaces with ends oftrim. Set trim and screws aside on protectedsurface.
Page 2
Electrical connectionIf your house has aluminum wiring, see"Electrical requirements", Page 2.
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.Failure to follow these instructions can resultin death, fire, or electrical shock.
This oven is manufactured with white {neutral)power supply wire and a cabinet=connected baregrounding wire twisted together.
Feed oven cable through opening inthe cabinet. Make electrical connection
foUUowingthe steps needed for your instaUUation.
1. Disconnect the power supply.2. Remove the junction box cover.3. Connect oven cable to junction box through the
U.L.qisted conduit connector.4. Connect the two black wires together with
twist-on connectors.5. Connect the two red wires together with
twist-on connectors.8. Complete electrical connection according to
local codes and ordinances.
cable from
iunetion power suppl,/
box _
white _ c>_
w,re _ _>_/¢"
grounding ovencable wires --
factory crimped
Figure 1 cable fromoven
conduitconnector
if local codes PERMIT
connectingcabinet-groundingconductor to neutral white
wire in junction box:
7. Connect the fac:tory°crimpedbare and white oven cable wiresto the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
eabb fromiunetion power supph!
Figure 2 eabte from connector
oven
ff local codes DO NOT PERMIT
connecting cabinet-groundingconductor to neutral white
wire in junction box:
7. Separate the factory-crimpedbare and white oven cable wires.
8. Connect white oven cable wire toneutral (white) wire in junctionbox. See Figure 2.
9. Connect the bare groundingoven cable wire to a groundedwire in the junction box. SeeFigure 2.
lg. Replace junction box cover.
ff connecting to afour-wire electrical system:
7. Separate bare and white ovencable wires.
8. Connect white oven cable wireto neutral (white) wire injunction box. See Figure 2.
9. Connect the bare groundingoven cable wire to the greengrounding wire in junction box.Do Not connect hare groundingwire to neutral (white} wire injunction box. See Figure 2.
10. Replace junction box cover.
AttachmentCarefully push against seal area of oven frontframe when pushing oven into cabinet.
Do Not push against outside edges, rti'
5m Lift oven into cabinet cutout using the
oven opening as an area to grip.
6u Important: Securely fasten oven to cabinet
using the screws provided (two screws for a singleoven or four screws for a double oven), Insert the
screws through hobs in mounting rails, Do Notovertighten screws.
screws
8u Replace oven racks.
important: Replace the door with the model/serialrating plate on the upper oven.On some models, the construction of this door isdesigned to withstand self-cbaning temperatures.
Reinstall the oven door by inserting endsof hinges into hinge slots in the oven frame. Pushhinges in as far as they will go. Open the door(you wiii feel the door drop into place} and rotateboth hinge latches back to the locked position.
Close and open the door to check that the doorcloses and opens completel% If door does notdose or open completely, repeat the doorremoval step and reinstall door as describedabove.
Repeat for lower oven door.
shippingfoot
Push against seal area of front frame to pushoven into cabinet until shipping feet almostcontact cabineL Use a Phillips screwdriver toremove screws attaching shipping feet. Removeand discard shipping feet.
Push oven completely into cabinet and centeroven in cabinet cutout.
Slide topof trim up. Push trim
:_ into prance.Replacetrim screw.
7m Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom oftrim. Use screws to attach each trim to oven. Takecare not to scratch other surfaces with ends of trim.
Check operation
O m Turn on power supply. The display
panel wili light up briefly. "PF" should appear inthe temperature display.
the display. Press the "START" pad. Make sure theoven door is closed and the "ON" light is shown inthe display area. After 2 minutes, partially openoven door. You should feel heat from the oven.Press the "CANCEL" pad.
Check the operation of your doubte oven.Press the "Upper Oven" pad. Pressthe "BROIL"pad. "BROIL" will appear in the display. Press the"START" pad. Make sure the oven door is closedand the "ON" light is shown in the display area.After 2 minutes, partially open oven door. Youshould feel heat from the oven. Pressthe"CANCEL" pad.Press the "Lower Oven" pad and repeat the stepsyou completed for checking the upper oven.
tf your oven does not heat or an "F, followedby a number, appears in the display, contactyour dealer or check the "If you need service..."section of this Installation Instructions.
To get the most efficient usefrom your new oven, read 7our
Use and Care Guide. Keep Installationmnstructions
and Guide close to oven
for easy reference.
Page 3
if oven does not operate:[_ Check that circuit breaker is not tdpped or
house fuse blown.
[_ See Use and Care Guide for troubleshooting list.
if you need assistance:ff you have questions about operating, c_eaning ormaintaining your oven:
[_ Refer to Use and Care Guide.
[_ Call the Consumer Assistance Center: Checkyour Use and Care Guide for a toll=freenumber to call or call the dealer from whom youpurchased tMs appliance. The dealer is listed inthe Yellow Pages of your phone dkectory under"Appliances -- Household -- Major -- Serviceand Repair."
if you need service:Maintain the quality built into your built-in oven bycalling an authorized service company.To obtain the name and number of an authorizedservice company:
[_ Contact the dealer from whom you purchasedyour built-in oven; or
[_ Look in the Yellow Pages of your telephonedirectory under "Appliances -- Household --Major -- Service and Repair" for an authorizedservice company; or
[_ Call the Consumer Assistance Center. The toll-free phone number is listed in your Use andCare Guide.
When you ca[[, you wi[[ need:
[_ The built-in oven model number.
[_ The built in oven serial number.
Both numbers are listed on the model/serial ratingp[ate, [ocated on the oven door or on the ovenframe.
Part No. 8300655© 2001 Printed in U.S.A.