-
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 1
PRELIMINARY DATA SHEET
SKY5®-8091-11 SkyOne® Low Band Tx-Rx Front-End Module for 3G/4G/5G Applications with Low Band / High Band 2G Applications
• Multi-band 2G 3G/4G/5G Mobile Devices • Handsets, Data Cards, M2M • LTE Advanced Carrier Aggregation (CA)
Features • MIPI® RFFE 2.0 control interfaces w/ 1.8 V nominal supply • Integrated switched duplexer filters for Bands 8, 12, 20 and 26 • Four auxiliary 3G/4G/5G Tx outputs for external filters • Four auxiliary 3G/4G/5G TRx ports to support additional bands • Tx filtering for harmonically-related LB-MB downlink CA • Integrated low band and high band 2G PAs • High band 2G works with companion MB/HB modules • Integrated bi-directional RF coupler with cascade support • Small, low profile package:
- 7.6 mm x 6.0 mm x 0.75 mm - 56-pad configuration
3G Features
- WCDMA, HSPA+ - CDMA2000 1x RC1, RC3, EVDO (Rev A)
4G Features
- FDD LTE - Uplink QPSK, 16QAM, 64QAM - Critical L+M, L+H Downlink CA Support
5G Features
- n5, n8, n12, n20, n28, n71
Description
The SKY58091-11 SkyOne® Multimode Multiband Tx-Rx Front-End Module (FEM) supports 2G/3G/4G/5G mobile devices and operates efficiently in 3G/4G/5G modes. The FEM consists of a low-band 3G/4G/5G PA block, low- and high-band 2G PA blocks, a silicon controller containing the MIPI RFFE interface, RF band switches, antenna switches, a bi-directional coupler, and integrated filters for Bands 8, 12, 20 and 26. Extremely low leakage current maximizes device standby time.
The IC die and passive components are mounted on a multi-layer laminate substrate. The assembly is encapsulated in a 7.6 mm x 6.0 mm x 0.75 mm, 56-pad MCM, SMT plastic package which allows a highly manufacturable, low cost solution.
The SKY58091-11 FEM is optimized for LTE Advanced which utilizes Carrier Aggregation for higher data rates. The combined filtering, RF matching and TRx switching internal to the FEM optimizes performance for popular Downlink (DL) CA band combinations in a compact and low cost solution. The FEM contains the necessary components between the antenna and RFIC transceiver and is optimized to provide superior Rx sensitivity and Tx efficiency.
Selecting the linear-GMSK operation standard disables VRAMP input, so all PA biasing depends only on MIPI mode selection. The transmitted envelope is then a linear function of RF input.
Selecting VRAMP-enabled operation, the PA controller provides VRAMP control of the GMSK envelope and reduces sensitivity to input drive, temperature, power supply, and process variations. Skyworks’ Finger-Based Integrated Power Amplifier Control (FB-iPAC) minimizes output power variation into mismatch.
In EDGE linear mode, VRAMP voltage and MIPI-based bias settings jointly optimize PA linearity and efficiency.
Exceptional RF coexistence planning and system techniques are employed to minimize Rx de-sensitizing ("de-sense").
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Figure 1. SKY58091-11 Functional Block Diagram
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 3
Electrical Specifications The following tables list the electrical characteristics of the SKY58091-11 Front-End Module. Table 1 lists the absolute maximum ratings and Table 2 shows the recommended operating
conditions. Electrical specifications for nominal operating conditions are listed in Tables 4 through 25.
The MIPI RFFE section contains information for mapping PA and ASM interfaces.
Table 1. SKY58091-11 Absolute Maximum Conditions1
Parameter Symbol Minimum Typical Maximum Unit
RF Input Power 3G/4G/5G Input PIN_3G4G5G 152 dBm
2G Input PIN_2G 153
TRx Input PIN_TRX 333
Supply Voltage No RF VCC_3G4G5G –0.5 6.0 V
VBATT / VCC_2G –0.5 6.0
RF VCC_3G4G5G –0.5 6.04
VBATT / VCC_2G –0.5 6.04
VIO –0.5 2.0
Temperature Ranges Storage TSTG –40 +150 °C
Operating TCASE –40 +25 +110
Electrostatic Discharge Sensitivity (ESD) IEC 61000-4-25 ESDIEC –1000 +1000 V
Human Body Model (HBM)6 Class 1C ESDHBM –1000 +1000
Human Body Model (HBM)6 RX Pads, Class 0 ESDHBM_Rx –250 +250
Charge Device Model (CDM)7, Class C2 ESDCDM –500 +500
1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value.
2 50 ohm load applied. CW duty cycle 100%, center channel of each band. 3 50 ohm load applied. CW duty cycle 2G 25% pulsed, 3G/4G 100%. 4 50 ohm load applied. 5 Applies to antenna ports only. 6 ANSI/ESDA/JEDEC Standard JS-001-2014 7 JEDEC Standard, JESD22-C101 Charge Device Model (CDM)
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 2. SKY58091-11 Recommended Operating Conditions
Parameter Symbol Minimum Typical Maximum Unit
Supply Voltage 3G/4G/5G VCC_3G4G5G1 0.5 3.4 4.2 V
Battery VBATT 3.0 3.8 4.8
MIPI VIO 1.65 1.80 1.95
Nominal Test Condition (NTC) VBATT 3.8 V
2G EDGE VCC_2G2 3.6
2G GMSK VCC_2G 3.5
3G/4G VCC_3G4G 3.4
5G VCC_5G 4.2
2G GMSK PIN_2G 33 dBm
TA4 +25 °C
Extreme Test Conditions (ETC) VBATT 3.0 4.8 V
2G GMSK VCC_2G 3.0 4.8
3G/4G/5G VCC_3G4G5G 4.2
2G GMSK PIN_2G 03 6 dBm
TA4 –20 +75 °C
RF Input Power5 3G/4G/5G PIN_3G4G5G 6 dBm
2G Burst Duty Cycle6 GMSK/EDGE 1-4 slots DB 12.5 50 %
Digital Control Signals Low SCLK, SDATA
–0.5 0 0.2*VIO V
High 0.8*VIO 1.8 VIO
SCLK Frequency Write speed 52 MHz
Read speed 26
VIO Rise Time TVIO-R 450 μs
1 Refer to SKY58091-11 bias table. The bias table will contain all MIPI settings and Vcc voltages used to meet performance specifications. The bias table will not exceed the specified maximum for VCC_3G/4G/5G.
2 VBATT and VCC_2G are assumed common. Value shown allows for ohmic supply loss. 3 VRAMP-based operation 4 In all cases, Ambient Operating Temperature (TA) is specified relative to Case Temperature (TC) and assumes TA = (TC – 10 °C). 5 Unless otherwise specified, RF specifications in this datasheet assume 50 Ω input and output termination, 12.5% duty cycle with
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 5
Table 4. SKY58091-11 Electrical Specifications – Linear GMSK/EDGE Power Modes – Recommended Maximum Operating Power– Unless otherwise specified, values are used as each Power Mode's Test Condition
Band Waveform Power Mode PRATED Unit
LB GMSK High Power Mode (HPM) 34.81 dBm
Medium Power Mode (MPM) 29.0
Low Power Mode (LPM) 23.0
Ultra-Low Power Mode (ULPM) 15.0
EDGE Medium Power Mode (MPM) 28.5
Low Power Mode (LPM) 22.0
Ultra-Low Power Mode (ULPM) 15.0
HB GMSK High Power Mode (HPM) 33.7
Medium Power Mode (MPM) 30.0
Low Power Mode (LPM) 26.0
Ultra-Low Power Mode (ULPM) 16.0
EDGE High Power Mode (HPM) 29.1
Medium Power Mode (MPM) 28.0
Low Power Mode (LPM) 24.0
Ultra-Low Power Mode (ULPM) 18.0 1 Vcc_2G =3.6V
Table 5. SKY58091-11 Electrical Specifications 4G/5G Prated – Recommended Maximum Operating Power Unless otherwise specified: LTE refers to MPR0
Band Modulation Power Mode Prated Unit
B8 LTE HPM 25.5 dBm
B26 LTE HPM 25.5
B20 LTE HPM 25.5
B12/17 LTE HPM 25.5
B28 LTE HPM 28.5
B13/14 LTE HPM 28.5
B71 LTE HPM 28.5
B5 WCDMA HPM 25.5
B8 WCDMA HPM 25.5
BC0 CDMA HPM 25.5
n5 NR APT, HPM 25.5
n8 NR APT, HPM 25.5
n12 NR APT, HPM 25.5
n20 NR APT, HPM 25.5
n28 NR APT, HPM 28.5
n71 NR APT, HPM 28.0
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 6. NR Test Waveform
n5/n8/n20/n28/n71 Channel Bandwidth (MHz) SCS (kHz) Modulation RB Allocation MPR (dB)
Test waveform 1 20 15 DFT-S-OFDM QPSK 50 @ 25 0
Test waveform 2 20 15 CP-OFDM QPSK 106 @ 0 3
Test waveform 3 20 15 CP-OFDM 256QAM 106 @ 0 6.5
Test waveform 4 20 15 CP-OFDM QPSK 53 @ 26 1.5
n12 Channel Bandwidth (MHz) SCS (kHz) Modulation RB Allocation MPR (dB)
Test waveform 1 15 15 DFT-S-OFDM QPSK 37 @ 18 0
Test waveform 2 15 15 CP-OFDM QPSK 79 @ 0 3
Test waveform 3 15 15 CP-OFDM 256QAM 79 @ 0 6.5
Test waveform 4 15 15 CP-OFDM QPSK 40 @ 20 1.5
Table 7. SKY58091-11 Electrical Specifications – Low Band 2G GMSK Tx at LB_ANT Pad – (VRAMP-based Operation) Unless otherwise specified: PRATED = 34.8 dBm; ETC per Table 2.
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency GSM850 ƒo 824 849 MHz
GSM900 880 915 MHz
Output Power POUT_MAX_NTC NTC, VRAMP = 1.65 V, PIN = 0 dBm 34.8 35.4 dBm
POUT_MAX_ETC VRAMP = 1.65 V, PIN = 0 dBm, VCC_2G = 3.0 V 32.8
Supply Current I2G_VCC Stability mismatch test conditions 3.2 A
Power Added Efficiency PAE NTC 38 %
Input VSWR ΓIN POUT ≤ PRATED 2.5:1
Harmonics 2nd 2ƒo 5 dBm ≤ Cal–POUT ≤ PRATED, VRAMP = Cal–VRAMP1 –40 –33 dBm 3rd 3ƒo –40 –33
4th or higher 4ƒo–13ƒo –40 –33
Noise Power in Rx Band 869 MHz–894 MHz PNOISE_850 NTC, ƒo in GSM8502 –82 dBm/100kHz 1930 MHz–1990 MHz –86
734 MHz–757 MHz –82
925 MHz–935 MHz PNOISE_900 NTC, ƒo in GSM9002 –79
935 MHz–960 MHz –82
1805 MHz–1880 MHz –86
2400 MHz–2500 MHz PNOISE_ISM NTC, ƒo in GSM850 or GSM900 –106
Isolation ISO_PD Isolation Mode, PIN ≤ 6 dBm, VRAMP ≤ 0.1 V –60 –51 dBm
ISO_PE GMSK Tx Mode, NTC, PIN ≤ 6 dBm, VRAMP ≤ 0.1 V –15
Mode Switching Time TMODE_2G Time from EDGE to GMSK mode transition to application of GMSK input drive to meet ISO_PE
2 μs
Stability S 5 dBm ≤ POUT ≤ PRATED, Load VSWR = 12:1, all phase angles
No parasitic oscillation > –36 dBm
Ruggedness Load 5 dBm ≤ POUT –≤ PRATED, Load VSWR = 20:1, all phase angles
No module damage nor permanent degradation
1 Cal-VRAMP = VRAMP at POUT = Cal-POUT, NTC 2 Prated
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 7
Table 8. SKY58091-11 Electrical Specifications – Low Band 2G EDGE Tx at LB_ANT Pad – (VRAMP-based Operation) Unless otherwise specified: VRAMP = 1.45 V; POUT = 28.5 dBm; ETC per Table 2.
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency GSM850 ƒo 824 849 MHz
GSM900 880 915 MHz
Maximum Output Power PRATED NTC, Gain / ACPR / EVM in specification 28.5 dBm
P_MAX_EX Gain / ACPR / EVM in specification 27.5
Gain G_NOM_850 NTC, POUT = PRATED 30.0 30.5 33.0 dB
G_NOM_900 30.0 30.5 33.0
G_EX_850 POUT = PMAX_EX 28.5 34.5
G_EX_900 28.5 34.5
Power Added Efficiency PAE_850 NTC 17.5 %
PAE_900 16.5
Input VSWR ΓIN POUT ≤ PRATED 2.5:1
Harmonics 2nd 2ƒo 5 dBm ≤ Cal-POUT ≤ PRATED –40 –36 dBm
3rd 3ƒo –40 –36
4th or higher 4ƒo-6ƒo –40 –36
ACPR ACPR_200 RBW = 30 kHz, POUT = PRATED, PMAX_EX –37 –35.5 dBc
ACPR_400 –62 –60
ACPR_600 –75 –70
EVM (RMS) EVM_RMS POUT = PRATED, PMAX_EX 2.0 3.5 %
Bias Switching Time T_ON_EDGE Rx to Tx transition time from final MIPI command and 90% VRAMP to 0.5 dB settling.
1 μs
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 9. SKY58091-11 Electrical Specifications – High Band 2G GMSK Tx at 2GHB_TX_OUT Pad – (VRAMP-based Operation) Unless otherwise specified: PRATED = 33.5 dBm; ETC per Table 2.
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency DCS ƒo 1710 1785 MHz
PCS 1850 1910
Output Power POUT_MAX_NTC NTC, VRAMP = 1.65 V, PIN = 0 dBm 33.7 34.3 dBm
POUT_MAX_ETC VRAMP = 1.65 V, PIN = 0 dBm, VCC_2G = 3.0 V 31.5
Supply Current I2G_VCC Stability mismatch test conditions 2.5 A
Power Added Efficiency PAE NTC 45 %
Input VSWR ΓIN POUT ≤ PRATED 2.5:1
Harmonics 2nd 2ƒo 0 dBm ≤ Cal-POUT ≤ PRATED, VRAMP = Cal-VRAMP1 –40 –33 dBm
3rd 3ƒo –30 –26
4th to 6th 4ƒo-6ƒo –38 –33
7 th 7ƒo –38 –28
Noise Power in Rx Band 1930 MHz–1990 MHz PNOISE_PCS NTC, POUT ≤ PRATED, ƒo in PCS –81 dBm/ 100 kHz
869 MHz–894 MHz –82
734 MHz–757 MHz –81
925 MHz–960 MHz PNOISE_DCS NTC, POUT ≤ PRATED, ƒo in DCS –80
1805 MHz–1880 MHz –79.5
2400 MHz–2500 MHz PNOISE_ISM NTC, POUT ≤ PRATED, ƒo in DCS or PCS –90
Isolation ISO_PD Isolation Mode, PIN ≤ 6 dBm, VRAMP ≤ 0.1 V –30 dBm
ISO_PE GMSK Tx Mode, NTC, PIN ≤ 6 dBm, VRAMP ≤ 0.1 V –15
Mode Switching Time TMODE_2G Time from EDGE to GMSK mode transition to application of GMSK input drive to meet ISO_PE
2 μs
Stability S 5 dBm ≤ P ≤ PRATED, Load VSWR = 8:1, all phase angles No parasitic oscillation > –36 dBm
Ruggedness Load 5 dBm ≤ POUT ≤ PRATED, Load VSWR = 10:1, all phase angles No module damage nor permanent degradation
1 Cal-VRAMP = VRAMP at POUT = Cal-POUT, NTC
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 9
Table 10. SKY58091-11 Electrical Specifications – High Band 2G EDGE Tx at 2GHB_TX_OUT Pad – (VRAMP-based Operation) Unless otherwise specified: VRAMP = 1.45 V, PRATED = 29.1 dBm; ETC per Table 2.
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency DCS ƒo 1710 1785 MHz
PCS 1850 1910
Maximum Output Power PRATED NTC, Gain / ACPR / EVM in specification 29.1 dBm
P_MAX_EX Gain / ACPR / EVM in specification 28.1
Gain G_NOM_DCS NTC, POUT = PRATED 34.2 35.7 37.2 dB
G_NOM_PCS 33.8 35.3 36.8
G_EX_DCS POUT = PMAX_EX 32.0 38.2
G_EX_PCS 30.8 37.5
Power Added Efficiency PAE_DCS NTC 24.0 %
PAE_PCS 24.0
Input VSWR ΓIN POUT ≤ PRATED 2.5:1
Harmonics 2nd 2ƒo 0 dBm ≤ Cal-POUT ≤ PRATED –40 –36 dBm
3rd 3ƒo –36 –33
4th or higher 4ƒo-7ƒo –40 –36
ACPR ACPR_200 RBW = 30 kHz, POUT = PRATED, PMAX_EX –37 –35.5 dBc
ACPR_400 –62 –59
ACPR_600 –75 –70
EVM (RMS) EVM_RMS POUT = PRATED, PMAX_EX 2.0 3.5 %
Bias Switching Time T_ON_EDGE Rx to Tx transition time from final MIPI command and 90% VRAMP to 0.5 dB settling.
1 μs
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 11-1. SKY58091-11 Electrical Specifications – GMSK/EDGE Low Band (Linear GMSK Operation) Unless otherwise specified: Conditions NTC per Table 2; Duty Cycle 25%; POUT = PRATED per “Power Modes” Table 4 at NTC, then varies with gain
Parameter Symbol Waveform/ Bias Mode Condition Min Typ Max Units
Operating Frequency Range 824 915 MHz
PSAT PSAT_GMSK GMSK HPM PIN = 9 dBm, NTC 34.81 35.0 dBm
PSAT Degraded PSAT_GMSK_ETC GMSK HPM PIN = 9 dBm, ETC 32.5 dBm
Power Added Efficiency, saturated PAE_GMSK_SAT GMSK HPM POUT = PSAT, PIN = 9 dBm 40 %
Power Added Efficiency PAE_GMSK GMSK HPM 38
GMSK MPM 20
GMSK LPM 10
GMSK ULPM 4
Gain GAIN_GMSK GMSK HPM1 26.0 28.0 30.0 dB
GMSK MPM 28.0 29.5 31.0
GMSK LPM 17.5 19.0 20.5
GMSK ULPM 17.0 18.5 20.0
GAIN_EDGE EDGE MPM 30.0 31.5 33.0 dB
EDGE LPM 28.0 29.5 31.0
EDGE ULPM 16.5 18.0 19.5
Gain Change Over Temperature GMSK HPM1 ETC, except VBATT = Vcc_2G = 3.5 V –1.7 1.0 dB
GMSK MPM –1.7 1.1
GMSK LPM –1.3 1.0
GMSK ULPM –1.0 0.6
Gain Change Over Voltage GMSK HPM1 ETC, except T = 25 °C –1.2 1.1 dB
GMSK MPM –0.5 0.5
GMSK LPM –0.5 0.5
GMSK ULPM –0.5 0.5
PAE PAE_EDGE EDGE MPM 17 %
Output Noise Power ALL NTC, Rx = 747 MHz to 757 MHz ---82 dBm/100 kHz
NTC, Rx = 757 MHz to 762 MHz ---82
NTC, Rx = 869 MHz to 894 MHz ---83
NTC, Rx = 925 MHz to 935 MHz ---80
NTC, Rx = 935 MHz to 960 MHz ---83
NTC, Rx = 1805 MHz to 1880 MHz ---90
NTC, Rx = 1930 MHz to 1990 MHz ---90
Harmonics 2nd 2ƒo GMSK ALL 5 dBm ≤ Cal–POUT ≤ PRATED –40 –33 dBm 3rd 3ƒo –40 –33
4th or higher 4ƒo–13ƒo –40 –33
Input Voltage Standing Wave Ratio VSWR_IN ALL 2.5:1
Stability S ALL VSWR
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 11
Table 11-2. SKY58091-11 Electrical Specifications – GMSK/EDGE Low Band (Linear GMSK Operation) Unless otherwise specified: Conditions NTC per Table 2; Duty Cycle 25%; POUT = PRATED per “Power Modes” Table 4 at NTC, then varies with gain
Parameter Symbol Waveform/ Bias Mode Condition Min Typ Max Units
Switching Transients SWT_400 GMSK HPM 400 kHz offset ETC PIN adjusted for Temperature
–28 dBm/30kHz
GMSK MPM –28
GMSK LPM –28
GMSK ULPM –28
ACPR (M-ORFS, No Pre-distortion)
ACPR_200 EDGE MPM 200 kHz offset ETC except VBATT ≥ 3.2 V PIN adjusted for Temperature MPM ETC PRATED = 28 dBm
–35.5 dBc/30 kHz
EDGE LPM –35.5
EDGE ULPM –35.5
ACPR_400 EDGE MPM 400 kHz offset ETC except VBATT ≥ 3.2 V PIN adjusted for Temperature MPM ETC PRATED = 28 dBm
–58
EDGE LPM –58
EDGE ULPM –58
ACPR_600 EDGE MPM 600 kHz offset ETC except VBATT ≥ 3.2 V PIN adjusted for Temperature MPM ETC PRATED = 28 dBm
–65
EDGE LPM –65
EDGE ULPM –65
EVM (No Pre-distortion) EVM_rms EDGE MPM ETC except VBATT ≥ 3.2 V PIN adjusted for Temperature MPM ETC PRATED = 28 dBm
2 4 %
EDGE LPM 2 4
EDGE ULPM 2 4
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 12-1. SKY58091-11 Electrical Specifications – High Band 2G GMSK/EDGE Tx at 2GHB_TX_OUT Pad (Linear GMSK Operation) Unless otherwise specified: Conditions NTC per Table 2; Duty Cycle 25%; POUT = PRATED per “Power Modes” Table at NTC, then varies with Gain
Parameter Symbol Waveform/ Bias Mode Condition Min Typ Max Units
Operating Frequency Range 1710 1910 MHz
PSAT PSAT_GMSK GMSK HPM PIN = 6 dBm, NTC 33.7 34.2 dBm
PSAT Degraded PSAT_GMSK_ETC GMSK HPM PIN = 6 dBm, ETC 31.5 dBm
Power Added Efficiency, saturated PAE_GMSK_SAT GMSK HPM POUT = PSAT, PIN = 6 dBm 48 %
Power Added Efficiency PAE_GMSK GMSK HPM 45 %
GMSK MPM 30
GMSK LPM 19
GMSK ULPM 6
Gain GAIN_GMSK GMSK HPM 30.0 32.0 34.0 dB
GMSK MPM 31.2 32.9 34.7
GMSK LPM 25.0 26.5 28.0
GMSK ULPM 21.0 22.7 24.5
GAIN_EDGE EDGE HPM 34.0 35.5 37.0 dB
EDGE MPM 33.4 35.2 37.0
EDGE LPM 29.5 31.0 32.5
EDGE ULPM 26.5 28.0 29.5
Gain Change Over Temperature GMSK HPM ETC, except VBATT = VCC_2G = 3.5 V –2.0 1.0 dB
GMSK MPM –1.6 1.0
GMSK LPM –1.0 1.0
GMSK ULPM –1.2 1.0
Gain Change Over Voltage GMSK HPM ETC, except T = 25 °C –1.3 1.3 dB
GMSK MPM –0.5 0.5
GMSK LPM –0.5 0.5
GMSK ULPM –0.5 0.5
PAE PAE_EDGE EDGE MPM 24 %
Output Noise Power ALL NTC, Rx = 747 MHz to 757 MHz –85 dBm/100kHz
NTC, Rx = 757 MHz to 762 MHz –85
NTC, Rx = 869 MHz to 894 MHz –85
NTC, Rx = 925 MHz to 935 MHz –85
NTC, Rx = 935 MHz to 960 MHz –85
NTC, Rx = 1805 MHz to 1880 MHz –79.5
NTC, Rx = 1930 MHz to 1990 MHz –81
Harmonics 2nd 2ƒo 0 dBm ≤ Cal-POUT ≤ PRATED –40 –33 dBm
3rd 3ƒo –30 –26
4th to 6th 4ƒo-6ƒo –38 –33
7th 7ƒo –38 –28
Input Voltage Standing Wave Ratio VSWR_IN ALL 2.5:1
Stability S ALL VSWR
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 13
Table 12-2. SKY58091-11 Electrical Specifications – High Band 2G GMSK/EDGE Tx at 2GHB_TX_OUT Pad (Linear GMSK Operation) Unless otherwise specified: Conditions NTC per Table 2; Duty Cycle 25%; POUT = PRATED per “Power Modes” Table at NTC, then varies with Gain
Parameter Symbol Waveform/ Bias Mode Condition Min Typ Max Units
Switching Transients SWT_400 GMSK HPM 400 kHz offset NTC per Table 2 ETC except VCC_2G ≥ 3.2 V PIN adjusted for Temperature
---28 dBm/30kHz
GMSK MPM ---28
GMSK LPM ---28
GMSK ULPM ---28
ACPR (M-ORFS, no pre-distortion)
ACPR_200 EDGE HPM 200 kHz offset NTC per Table 2 ETC except VCC_2G ≥ 3.2 V PIN adjusted for Temperature ETC PRATED = 28.1 dBm
–35.5 dBc/30kHz
EDGE MPM –35.5
EDGE LPM –35.5
EDGE ULPM –35.5
ACPR_400 EDGE HPM 400 kHz offset NTC per Table 2 ETC except VCC_2G ≥ 3.2 V PIN adjusted for Temperature ETC PRATED = 28.1 dBm
–58
EDGE MPM –58
EDGE LPM –58
EDGE ULPM –58
ACPR_600 EDGE HPM 600 kHz offset NTC per Table 2 ETC except VCC_2G ≥ 3.2 V PIN adjusted for Temperature ETC PRATED = 28.1 dBm
–65
EDGE MPM –65
EDGE LPM –65
EDGE ULPM –65
EVM (no pre–distortion) EVM_RMS EDGE MPM NTC per Table 2 ETC except VCC_2G ≥ 3.2 V PIN adjusted for Temperature ETC PRATED = 28.1 dBm
2 4 %
EDGE LPM 2 4
EDGE ULPM 2 4
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 13-1. SKY58091-11 Electrical Specifications – Band 8 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 880 915 MHz
Maximum 3G Output Power POUT_MAX_3G_NTC R99 RMC 12.2 kbps 25.5 dBm
POUT_MAX_3G_ETC R99 RMC 12.2 kbps, ETC 24.5
Maximum LTE Output Power POUT_MAX_LTE_NTC 25.5 dBm POUT_MAX_LTE_ETC ETC 24.5
Maximum NR Output Power POUT_MAX_NR_NTC VCC_5G = 3.7 V 25.5 dBm
RF Input Power PIN_3G4G5G 100% duty cycle 3.5 dBm
Gain G_NTC VCC_3G4G = 3.4 V 25.0 26.8 28.5 dB
G_ETC ETC, VCC_3G4G = 3.4 V 23.0 29.0
WCDMA System DC Current Referred to VBATT1 I_TOTAL_R99 PMIC Efficiency = 95%, POUT = 25.5dBm, R99 RMC 12.2 kbps, VCC_3G4G = 3.4 V, ƒo = 900 MHz
539 576 mA
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 24.5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.2 V, ƒo = 900 MHz
435 470 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 1 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –70 –50 dBm
3ƒo 3ƒo –75 –55
4ƒo 4ƒo –70 –50
5ƒo and higher 5ƒo –40
Rx Band Noise Power3 NRx Measured at Rx port –183 –180 dBm/Hz
GPS and GLONASS Band Noise3 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –165 dBm/Hz
LB WiFi Band Noise3 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –165 dBm/Hz
HB WiFi Band Noise3 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –160 dBm/Hz
Tx Level at B8 Rx Port PTx-Rx 880–915 MHz, LTE 10 MHz 10M12RB (MPR = 0) –30 –28 dBm
Isolation Tx-Rx ISO_Tx-Rx 925–960 MHz, (s21 4GLB_IN to Rx port) – PA gain 55 dB
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 15
Table 13-2. SKY58091-11 Electrical Specifications – Band 8 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
ACLR WCDMA ±5 MHz ACLR1_R99_NTC R99 RMC 12.2 kbps –42 –38 dBc
ACLR1_R99_ETC R99 RMC 12.2 kbps, ETC –36
ACLR WCDMA ±10 MHz ACLR2_R99_NTC R99 RMC 12.2 kbps –54 –48 dBc
ACLR2_R99_ETC R99 RMC 12.2 kbps, ETC –46
E-UTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc
UTRA2_LTE_ETC ETC –39
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.8 % rms
EVM_NR_ETC Test waveform 3, ETC 1.8
EVM, NR EVM_NR_NTC Test waveform 1,2,4 2.5 4
EVM_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR _NR_NTC Test waveform 2 –39 –37 dBc
ACLR _NR_ETC Test waveform 2, ETC –33
NR ACLR ACLR _NR_NTC Test waveform 1,3,4 –40 –38
ACLR _NR_ETC Test waveform 1,3,4, ETC –33
NR UTRA1 UTRA1_NR_NTC Test waveform 1/2/3/4 –42 –39 dBc
UTRA1_NR_ETC Test waveform 1/2/3/4, ETC –36
NR UTRA2 UTRA2_NR_NTC Test waveform 1/2/3/4 –42 –41 dBc
UTRA2_NR_ETC Test waveform 1/2/3/4, ETC –39
EVM, WCDMA EVM_R99_NTC RMS, R99 RMC 12.2 kbps 3.0 % rms
EVM_R99_ETC RMS, R99 RMC 12.2 kbps, ETC 3.0
EVM, LTE EVM_LTE_NTC RMS, modulation = QPSK, 16QAM, 64QAM 3.0 5 % rms
EVM_LTE_ETC RMS, modulation = QPSK, 16QAM, 64QAM, ETC 3.0 5
Input VSWR VSWR_IN 1.5:1 2.3:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Applies to Band 3 and Band 7 Rx frequencies 3 Measured at Rx port, QPSK 10 MHz 25RB, harmonics excluded.
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 14. SKY58091-11 – Electrical Specifications – Band 8 Rx Performance Unless otherwise specified: Environmental Conditions = NTC per Table 2; CW, 50 ohm termination
Parameter Symbol Conditions Min Typ Max Unit
Frequency Range ƒo 925 960 MHz
Insertion Loss RxIL_NTC Rx Band1 2.2 3.1 dB
Rx Port VSWR VSWR_Rx_ETC Rx Band 1.5:1 2.2:1
ANT Port VSWR VSWR_ANT_ETC Rx Band, ETC 2.0:1
Absolute Attenuation LB Antenna to Rx pad 1427 MHz–2200 MHz 40 dB
2300 MHz–2690 MHz 35
2400 MHz–2494 MHz 40
5150 MHz–5850 MHz 40
1 Duplexer Rx port mismatch removed per optimized LNA match
Table 15-1. SKY58091-11 Electrical Specifications – Band 26 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 814 849 MHz
Maximum 3G Output Power POUT_MAX_3G_NTC R99 RMC 12.2 kbps / CDMA 1x RC1 25.5 dBm
POUT_MAX_3G_ETC R99 RMC 12.2 kbps / CDMA 1x RC1, ETC 24.5
Maximum LTE Output Power POUT_MAX_LTE_NTC 25.5 dBm
POUT_MAX_LTE_ETC ETC 24.5
Maximum NR Output Power POUT_MAX_NR_NTC VCC_5G = 3.6 V 25.5 dBm
RF Input Power PIN_3G4G5G 100% duty cycle 3.5 dBm
Gain G_NTC VCC_3G4G = 3.4 V 26.0 27.5 29.0 dB
G_ETC ETC, VCC_3G4G = 3.4 V 24.3 30.5
WCDMA System DC Current Referred to VBATT1 I_TOTAL_R99 PMIC Efficiency = 95%, POUT = 25.5dBm, R99 RMC 12.2 kbps, VCC_3G4G = 3.4 V, ƒo = 832 MHz
489 510 mA
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 24.5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.4 V, ƒo = 832 MHz
410 434 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 1 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –40 dBm
3ƒo 3ƒo –65 –45
4ƒo and higher nƒo –40
Rx Band Noise Power2 NRx Measured at Rx port –183 –180 dBm/Hz
GPS and GLONASS Band Noise2 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –165 dBm/Hz
LB WiFi Band Noise2 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –165 dBm/Hz
HB WiFi Band Noise2 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –160 dBm/Hz
Tx Level at B26 Rx Port PTx-Rx 814–849 MHz, LTE 10 MHz 10M12RB ( MPR = 0 ) –30 –28 dBm
Isolation Tx-Rx ISO_Tx-Rx 859–894 MHz, (s21 4GLB_IN to Rx port) – PA gain 55 dB
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 17
Table 15-2. SKY58091-11 Electrical Specifications – Band 26 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
ACLR WCDMA ±5 MHz ACLR1_R99_NTC R99 RMC 12.2 kbps –42 –38 dBc
ACLR1_R99_ETC R99 RMC 12.2 kbps, ETC –36
ACLR WCDMA ±10 MHz ACLR2_R99_NTC R99 RMC 12.2 kbps –54 –48 dBc
ACLR2_R99_ETC R99 RMC 12.2 kbps, ETC –46
ACLR CDMA ±885 kHz ACLR1_C2K_NTC CDMA 1x RC1 –50.0 –47 dBc
ACLR1_C2K_ETC CDMA 1x RC1, ETC –49.0 –45
ACLR CDMA ±1.98 MHz ACLR2_C2K_NTC CDMA 1x RC1 –60.0 –57 dBc
ACLR2_C2K_ETC CDMA 1x RC1, ETC –58.5 –55
E-UTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc
UTRA2_LTE_ETC ETC –39
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.8 % rms
EVM_NR_ETC Test waveform 3, ETC 1.8
EVM, NR EVM_NR_NTC Test waveform 1,2,4 2.5 4
EVM_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR_NR_NTC Test waveform 2 –39 –37 dBc
ACLR_NR_ETC Test waveform 2, ETC –33
NR ACLR ACLR_NR_NTC Test waveform 1,3,4 –40 –38
ACLR_NR_ETC Test waveform 1,3,4, ETC –33
NR UTRA1 UTRA1_NR_NTC Test waveform 1/2/3/4 –42 –39 dBc
UTRA1_NR_ETC Test waveform 1/2/3/4, ETC –36
NR UTRA2 UTRA2_NR_NTC Test waveform 1/2/3/4 –42 –41 dBc
UTRA2_NR_ETC Test waveform 1/2/3/4, ETC –39
EVM, WCDMA EVM_R99_NTC RMS, R99 RMC 12.2 kbps 3.0 % rms
EVM_R99_ETC RMS, R99 RMC 12.2 kbps, ETC 3.0
EVM, LTE EVM_LTE_NTC RMS, modulation = QPSK, 16QAM, 64QAM 3.0 5 % rms
EVM_LTE_ETC RMS, modulation = QPSK, 16QAM, 64QAM, ETC 3.0 5
Input VSWR VSWR_IN 1.5:1 2:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Measured at Rx port, QPSK 10MHz 25RB, harmonics excluded.
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 18 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 16. SKY58091-11 Electrical Specifications – Band 26 Rx Performance Unless otherwise specified: Environmental Conditions = NTC per Table 2; CW, 50 ohm termination
Parameter Symbol Conditions Min Typ Max Unit
Rx Frequency Range ƒo 859 894 MHz
Insertion Loss RxIL_NTC Rx Band1 2.2 3.0 dB
Rx Port VSWR VSWR_Rx_ETC Rx Band, ETC 1.5:1 2.2:1
ANT Port VSWR VSWR_ANT_ETC Rx Band, ETC 2.0:1
Absolute Attenuation LB Antenna to Rx pad 1427MHz–2200 MHz 40 dB
2300 MHz–2690 MHz 35
2400 MHz–2494 MHz 40
5150 MHz–5850 MHz 40
1 Rx port mismatch removed per optimized LNA match.
Table 17-1. SKY58091-11 Electrical Specifications – Band 20 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 832 862 MHz
Maximum LTE Output Power POUT_MAX_LTE_NTC 25.5 dBm
POUT_MAX_LTE_ETC ETC 24.5
Maximum NR Output Power POUT_MAX_NR_NTC VCC_5G = 3.8 V 25.5 dBm
RF Input Power PIN_3G4G5G 100% duty cycle 3.5 dBm
Gain G_NTC VCC_3G4G = 3.4 V 26.0 27.5 29.0 dB
G_ETC ETC, VCC_3G4G = 3.4 V 24.4 30.0
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 24.5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.4 V, ƒo = 847 MHz
427 452 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, APT Mode, POUT = 1 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –40 dBm
3ƒo 3ƒo –65 –45
4ƒo and higher nƒo –40
Rx Band Noise Power2 NRx Measured at Rx port –183 –180 dBm/Hz
GPS and GLONASS Band Noise2 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –165 dBm/Hz
LB Wi-Fi Band Noise2 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –165 dBm/Hz
HB Wi-Fi Band Noise2 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –160 dBm/Hz
Tx Level at B20 Rx Port PTx-Rx 832–862 MHz, LTE 10 MHz 10M12RB ( MPR = 0 ) –30 –28 dBm
Isolation Tx-Rx ISO_Tx-Rx 791–821 MHz, (s21 4GLB_IN to Rx port) – PA gain 55 dB
E-UTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –36
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 19
Table 17-2. SKY58091-11 Electrical Specifications – Band 20 Tx Performance at LB_ANT Pad
Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc
UTRA2_LTE_ETC ETC –39
EVM, LTE EVM_LTE_NTC RMS, modulation = QPSK, 16QAM, 64QAM 3.0 5 % rms
EVM_LTE_ETC RMS, modulation = QPSK, 16QAM, 64QAM, ETC 3.0 5
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.8 % rms
EVM_NR_ETC Test waveform 3, ETC 1.8
EVM, NR EVM_NR_NTC Test waveform 1,2,4 2.5 4
EVM_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR_NR_NTC Test waveform 2 –39 –37 dBc
ACLR_NR_ETC Test waveform 2, ETC –33
NR ACLR ACLR_NR_NTC Test waveform 1,3,4 –40 –38
ACLR_NR_ETC Test waveform 1,3,4 ETC –33
NR UTRA1 UTRA1_NR_NTC Test waveform 1/2/3/4 –42 –39 dBc
UTRA1_NR_ETC Test waveform 1/2/3/4, ETC –36
NR UTRA2 UTRA2_NR_NTC Test waveform 1/2/3/4 –42 –41 dBc
UTRA2_NR_ETC Test waveform 1/2/3/4, ETC –39
Input VSWR VSWR_IN 1.5:1 2:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Measured at Rx port, QPSK 20 MHz 20RB_16, QPSK 10 MHz 20RB_0, harmonics excluded.
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 20 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 18. SKY58091-11 Electrical Specifications – Band 20 Rx Performance Unless otherwise specified: Environmental Conditions = NTC per Table 2; CW, 50 ohm termination
Parameter Symbol Conditions Min Typ Max Unit
Rx Frequency Range ƒo 791 821 MHz
Insertion Loss RxIL_NTC Rx Band1 2.2 3.0 dB
Rx Port VSWR VSWR_Rx_ETC Rx Band, ETC 1.5:1 2.6:1
ANT Port VSWR VSWR_ANT_ETC Rx Band, ETC 2.0:1
Absolute Attenuation LB Antenna to Rx pad 1427 MHz–2200 MHz 40 dB
2300 MHz–2690 MHz 35
2400 MHz–2494 MHz 40
5150 MHz–5850 MHz 38 1 Rx port mismatch removed per optimized LNA match.
Table 19-1. SKY58091-11 Electrical Specifications – Band 12/17 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 699 716 MHz
Maximum LTE Output Power POUT_MAX_LTE_NTC 25.5 dBm POUT_MAX_LTE_ETC ETC 24.5
RF Input Power PIN_3G4G5G 100% duty cycle 3.5 dBm
Gain G_NTC VCC_3G4G = 3.4 V 27.0 28.5 30.5 dB
G_ETC ETC, VCC_3G4G = 3.4 V 25.0 32.0
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 24 .5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.2 V, ƒo = 708 MHz
433 460 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 1 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –40 dBm
3ƒo2 3ƒo –80 –60
4ƒo and higher 4ƒo–nƒo –40
Rx Band Noise Power3 NRx Measured at Rx port –183 –180 dBm/Hz
GPS and GLONASS Band Noise3 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –165 dBm/Hz
LB WiFi Band Noise3 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –165 dBm/Hz
HB WiFi Band Noise3 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –160 dBm/Hz
Tx Level at B12 Rx Port PTx-Rx LTE 10 MHz/12RB (MPR = 0) –30 –28 dBm
Isolation Tx-Rx ISO_Tx-Rx (s21 4GLB_IN to Rx port) – PA gain 55 dB
E-UTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 21
Table 19-2. SKY58091-11 Electrical Specifications – Band 12/17 Tx Performance at LB_ANT Pad Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc
UTRA2_LTE_ETC ETC –39
EVM, LTE EVM_LTE_NTC RMS, modulation = QPSK, 16QAM, 64QAM 3.0 5 % rms
EVM_LTE_ETC RMS, modulation = QPSK, 16QAM, 64QAM, ETC 3.0 5
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.8 %rms
EVM_NR_ETC Test waveform 3, ETC 1.8
EVM, NR ACLR_NR_NTC Test waveform 1,2,4 2.5 4
ACLR_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR_NR_NTC Test waveform 1,2,3,4 -40 -38 dBc
ACLR_NR_ETC Test waveform 1,2,3,4, ETC -33
NR UTRA1 UTRA1_NR_NTC Test waveform 1,2,3,4 -42 -39 dBc
UTRA1_NR_ETC Test waveform 1,2,3,4, ETC -36
NR UTRA2 UTRA2_NR_NTC Test waveform 1,2,3,4 -42 -41 dBc
UTRA2_NR_ETC Test waveform 1,2,3,4, ETC -39
Input VSWR VSWR_IN 1.5:1 2:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, Antenna port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Applies to Band 4 Rx frequencies 3 Measured at Rx port, QPSK 10 MHz 20RB_30, harmonics excluded.
Table 20. SKY58091-11 Electrical Specifications – Band 12/17 Rx Performance Unless otherwise specified: Environmental Conditions = NTC per Table 2; CW, 50 ohm termination
Parameter Symbol Conditions Min Typ Max Unit
Rx Frequency Range ƒo 729 746 MHz
Insertion Loss RxIL_NTC Rx Band 2.1 2.9 dB
Rx Port VSWR VSWR_Rx_ETC Rx Band, ETC 1.5:1 2.2:1
ANT Port VSWR VSWR_ANT_ETC Rx Band, ETC 2.0:1
Absolute Attenuation LB Antenna to Rx pad 1427 MHz–2200 MHz 40 dB
2300 MHz–2690 MHz 35
2400 MHz–2494 MHz 40
5150 MHz–5850 MHz 40
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 22 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 21. SKY58091-11 Electrical Specifications – Band 28 Tx Performance at Auxiliary TX_OUT Pads Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 703 748 MHz
Maximum LTE Output Power POUT_MAX_LTE_NTC 28.5 dBm
POUT_MAX_LTE_ETC ETC 27.5
Maximum NR Output Power POUT_MAX_NR_NTC VCC_5G = 4 V 28.5
Gain G_NTC VCC_3G4G = 3.4 V 28.0 29.5 31.5 dB
G_ETC ETC, VCC_3G4G = 3.4 V 26.0 33.0
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 27.5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.4 V, ƒo = 733 MHz
510 532 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 3 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –17 dBm
3ƒo 3ƒo –30
4ƒo and higher nƒo –38
Rx Band Noise Power2 NRx –127 dBm/Hz
GPS and GLONASS Band Noise2 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –140 dBm/Hz
LB WiFi Band Noise2 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –140 dBm/Hz
HB WiFi Band Noise2 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –140 dBm/Hz
EVM, RMS EVM_LTE_NTC 3.0 5.0 % rms EVM_LTE_ETC ETC 3.0 5.0
EUTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc UTRA1_LTE_ETC ETC –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc UTRA2_LTE_ETC ETC –39
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.8 % rms
EVM_NR_ETC Test waveform 3, ETC 1.9
EVM, NR EVM_NR_NTC Test waveform 1,2,4 2.5 4
EVM_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR_NR_NTC Test waveform 2 –39 –36 dBc
ACLR_NR_ETC Test waveform 2, ETC –33
NR ACLR ACLR_NR_NTC Test waveform 1,3,4 –39 –37
ACLR_NR_ETC Test waveform 1,3,4, ETC –33
NR UTRA1 UTRA1_NR_NTC Test waveform 1/2/3/4 –42 –39 dBc
UTRA1_NR_ETC Test waveform 1/2/3/4, ETC –36
NR UTRA2 UTRA2_NR_NTC Test waveform 1/2/3/4 –42 –41 dBc
UTRA2_NR_ETC Test waveform 1/2/3/4, ETC –39
Input VSWR VSWR_IN 1.5:1 2:1 Stability, spurious emissions S ETC, POUT ≤ PRATED,
TX_OUT port VSWR = 6:1, all phase angles –36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, TX_OUT port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Measured at Aux port, QPSK 10MHz 25RB, harmonics excluded.
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 23
Table 22. SKY58091-11 Electrical Specifications – Band 13/14 Tx Performance at Auxiliary TX_OUT Pads Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 777 798 MHz
Maximum LTE Output Power POUT_MAX_LTE_NTC 28.5 dBm POUT_MAX_LTE_ETC ETC 27.5
Gain G_NTC VCC_3G4G = 3.4 V 28.5 30.0 32.0 dB
G_ETC ETC, VCC_3G4G = 3.4 V 27.0 33.0
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 27.5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.4 V, ƒo = 782 MHz
500 526 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 3 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –17 dBm
3ƒo 3ƒo –30
4ƒo and higher nƒo –38
Rx Band Noise Power2 NRx –122 –121 dBm/Hz GPS and GLONASS Band Noise2 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –140 dBm/Hz
LB WiFi Band Noise2 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –140 dBm/Hz
HB WiFi Band Noise2 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –140 dBm/Hz
EVM, RMS EVM_LTE_NTC 3.0 5.0 % rms
EVM_LTE_ETC ETC 3.0 5.0
EUTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc
UTRA2_LTE_ETC ETC –39
Input VSWR VSWR_IN 1.5:1 2:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, TX_OUT port VSWR = 6:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, TX_OUT port VSWR = 10:1, all phase angles
No module damage nor permanent degradation
1 VCC_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Measured at Aux port, QPSK 10MHz 20RB_0 for B13, QPSK 10MHz 15RB_0 for B14.
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 24 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 23 SKY58091-11 Electrical Specifications – Band 71 Tx Performance at Auxiliary TX_OUT Pads Unless otherwise specified: NTC per Table 2, POUT = POUT_MAX, LTE modulation = QPSK/10MHz/12RB; Average Power Tracking (APT) Mode
Parameter Symbol Conditions Min Typ Max Unit
Operating Frequency ƒo 663 698 MHz
Maximum LTE Output Power POUT_MAX_LTE_NTC 28.5 dBm
POUT_MAX_LTE_ETC ETC 27.5
Maximum NR Output Power POUT_MAX_NR_NTC VCC_5G = 4.1 V 28.0
Gain G_NTC VCC_3G4G = 3.4 V 27.5 29.0 31.0 dB
G_ETC ETC, VCC_3G4G = 3.4 V 26.0 32.5
APT LTE System DC Current Referred to VBATT1 I_TOTAL_LTE PMIC Efficiency = 95%, POUT = 27 .5 dBm, QPSK 10 MHz 50RB, VCC_3G4G = 3.4 V, ƒo = 681 MHz
554 574 mA
LPM LTE System DC Current Referred to VBATT1 I_TOTAL_LTE_LPM PMIC Efficiency = 75%, POUT = 3 dBm, QPSK 10 MHz 50RB
12 mA
Harmonic 2ƒo 2ƒo LTE 1RB, MBW = 1 MHz, ETC –8 dBm
3ƒo 3ƒo –20
4ƒo and higher nƒo –20
Rx Band Noise Power2 NRx –127 dBm/Hz
GPS and GLONASS Band Noise2 NGPS 1574–1577 MHz GPS, 1597–1607 MHz GLONASS –140 dBm/Hz
LB WiFi Band Noise2 NLB-WiFi 2.4 GHz WiFi, 2400–2495 MHz –140 dBm/Hz
HB WiFi Band Noise2 NHB-WiFi 5 GHz WiFi, 4900–5850 MHz –140 dBm/Hz
EVM, RMS EVM_LTE_NTC 3.0 5.0 % rms
EVM_LTE_ETC ETC 3.0 5.0
EUTRA ACLR E-UTRA_LTE_NTC –39 –36 dBc
E-UTRA_LTE_ETC ETC –33
UTRA ACLR1 UTRA1_LTE_NTC –40 –38 dBc
UTRA1_LTE_ETC ETC –39 –36
UTRA ACLR2 UTRA2_LTE_NTC –42 –41 dBc UTRA2_LTE_ETC ETC –39
EVM, NR EVM_NR_NTC Test waveform 3 1.5 1.9 % rms
EVM_NR_ETC Test waveform 3, ETC 2.1
EVM, NR EVM_NR_NTC Test waveform 1,2,4 2.5 4
EVM_NR_ETC Test waveform 1,2,4, ETC 4
NR ACLR ACLR_NR_NTC Test waveform 2 –39 –36 dBc
ACLR_NR_ETC Test waveform 2, ETC –33
NR ACLR ACLR_NR_NTC Test waveform 1/3/4 –40 –38
ACLR_NR_ETC Test waveform 1/3/4, ETC –33
NR UTRA1 UTRA1_NR_NTC Test waveform 1/2/3/4 –42 –39 dBc
UTRA1_NR_ETC Test waveform 1/2/3/4, ETC –36
NR UTRA2 UTRA2_NR_NTC Test waveform 1/2/3/4 –42 –41 dBc
UTRA2_NR_ETC Test waveform 1/2/3/4, ETC –39
Input VSWR VSWR_IN 1.5:1 2:1
Stability, spurious emissions S ETC, POUT ≤ PRATED, TX_OUT port VSWR = 6:1, all phase angles
–36 dBm
Ruggedness Ru ETC, POUT ≤ PRATED, TX_OUT port VSWR = 10:1, all phase angles
no module damage nor permanent degradation
1 Vcc_3G4G voltage is optimized to meet the typical ("Typ") ACLR performance level. 2 Measured at Aux port, QPSK 10 MHz 20RB_0.
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 25
Table 24. SKY58091-11 Electrical Specifications – Auxiliary LB_TRX Input Performance (LB_TRX1–4 Pads) Unless otherwise specified: NTC per Table 2; LB_TRX1–4; CW
Parameter Symbol Conditions Min Typ Max Unit
Frequency Range ƒo 617 960 MHz
RF Peak Input Power Handling PIN_TRX_PEAK 36 dBm
Insertion Loss TRx to ANT IL_TRX 0.7 0.91 dB
Harmonics (2ƒo to 3ƒo) 2ƒo to 3ƒo PIN_TRX = 27 dBm –75 dBm
Harmonics (4ƒo to 7ƒo) 4ƒo to 7ƒo PIN_TRX = 27 dBm –75 dBm
Input VSWR VSWR_TRX 1.2:1 1.5:12
Isolation (selected TRX to adjacent TRX ) ISO_ADJACENT 30 dB
Isolation (selected TRX to non-adjacent TRX ) ISO_NON_ADJACENT 353 dB
1 Max. IL @ B8 ƒ = 1.0 dB 2 Max. input VSWR @ B8 ƒ = 1.8:1 3 Min. isolation between TRX1–TRX3 = 32 dB
Table 25. SKY58091-11 – Low-Band Directional Coupler Performance Unless otherwise specified: NTC per Table 2; Internal Coupler Forward Operation; CW
Parameter Symbol Conditions Min Typ Max Unit
Frequency Range ƒo 663 915 MHz
Coupler Switch Insertion Loss CPL_LOSS Daisy chain operation, Freq = 600 MHz to 2700 MHz 0.7 1.3 dB
Coupler In-Out Switch Isolation CPL_IN_OUT_ISO Daisy Chain operation, Freq = 600 MHz to 2700 MHz 25 dB
Forward Coupling Factor CPL_FACTOR_FWD 21.5 26.5 dB
Forward Coupler Directivity1 CPL_DIR_FWD 20 22 dB
Reverse Coupling Factor CPL_FACTOR_REV 21.5 26.5 dB
Reverse Coupling Directivity1 CPL_DIR_REV 15 18 dB
1 Directivity = Isolation – Coupling Factor
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 26 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
MIPI RFFE Information Table 26-1. SKY58091-11 MIPI RFFE Register Map (VRAMP-based Operation)
Regi
ster
Add
ress
(H
ex)
Register Name Fiel
d Bi
ts
Field Name Description Defa
ult V
alue
BSID
/GSI
D Su
ppor
t
Trig
ger S
uppo
rt
Ext R
eg R
/W
R/W
0x00 PA_CTRL [7] Register Map & Power Control Selector
set to 1 to select this VRAMP GMSK Power Control register map 0 N Trigger 1 Y RW
[6:3] PA_MODE_CTRL PA Mode and Band Switch Control 0x0
0x0: PA OFF 0xA: 4G B20
0x1: 2G LB GMSK 0xB: 4G LB_Tx2_OUT
0x2: 2G HB GMSK 0xC: 4G B8
0x3: 2G LB EDGE 0xD: 4G LB_Tx3_OUT
0x4: 2G HB EDGE 0xE: 4G B26
0x7: PA OFF 0xF: 4G B12
0x8: 4G LB_TX4_OUT All other: reserved
0x9: 4G LB_TX1_OUT
[2] PA_EN PA Enable 0: OFF 0
1: ON
[1:0] PA_GAIN_CTRL 2G Gain Reduction 0X = Nominal Gain 00
1X = Reduced Gain
3G/4G/5G Bias Select
0x01 PA_BIAS0 [7:4] Iref2 2G Iref3 3G/4G/5G Iref2 0x0 N Trigger 1 Y RW
0x0: 250μA 0x0: 0μA
0x1: 500μA 0x1: 125μA
0x2: 750μA 0x2: 250μA
…. ….
1xE: 3750μA 1xE: 1750μA
1xF: 4000 μA 1xF: 1875 μA
[3:0] Iref1 2G Iref12 3G/4G/5G Iref1 0x0
0x0: 250 μA 0x00: 0 μA
0x1: 500 μA 0x1: 150 μA
0x2: 750 μA 0x2: 300 μA
…. ….
1xE: 3750\μA 1xE: 2100 μA
1xF: 4000 μA 1xF: 2250 μA
0x05 ASM_CTRL [7:5] (Reserved) Reserved, set to zero 000 N Trigger 0 Y RW
[4] MBShuntARM 0x00:MB shunt ARM OFF 0
0x01:MB shunt ARM ON
[3:0] ASM_SW_CTRL Antenna switch state 0x0
0x0: Isolation/Stand-by 0x7: B8
0x1: TRx1 0x8: B26
0x2: TRx2 0xC: Isolation
0x3: TRx3 0xD: Isolation
0x4: TRx4 0xE:LB_ANT terminated
0x5: B20 0xF: LB_2G_TX
0x6: B12 All others reserved
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 27
Table 26-2. SKY58091-11 MIPI RFFE Register Map (Linear GMSK Power Control Only)
Regi
ster
Add
ress
(H
ex)
Register Name Fiel
d Bi
ts
Field Name Description Defa
ult V
alue
BSID
/GSI
D Su
ppor
t
Trig
ger S
uppo
rt
Ext R
eg R
/W
R/W
0x00 PA_CTRL [7] Register Map & Power Control Selector
set to 0 to select this Linear GMSK Power Control register map 0 N Trigger 1 Y RW
[6:3] PA_MODE_CTRL PA Mode and Band Switch Control 0x0
0x0: PA OFF 0xA: 4G B20
0x1: 2G LB GMSK 0xB: 4G LB_Tx2_OUT
0x2: 2G HB GMSK 0xC: 4G B8
0x3: 2G LB EDGE 0xD: 4G LB_Tx3_OUT
0x4: 2G HB EDGE 0xE: 4G B26
0x7: PA OFF 0xF: 4G B12
0x8: 4G LB_Tx4_OUT All other: reserved
0x9: 4G LB_Tx1_OUT 3G/4G/5G Bias Select
[2] PA_EN PA Enable 0: OFF 0
1: ON
[1:0] PA_GAIN_CTRL 2G Power Mode 00 = HPM 10 = LPM 00
01 = MPM 11 = ULPM
3G/4G/5G Bias Select
0x01 PA_BIAS [7:4] Iref2 2G Iref3 3G/4G/5G Iref2 0x0 N Trigger 1 Y RW
0x0: 250 μA 0x0: 0 μA
0x1: 500 μA 0x1: 125 μA
0x2: 750 μA 0x2: 250 μA
…. ….
1xE: 3750 μA 1xE: 1750 μA
1xF: 4000 μA 1xF: 1875 μA
[3:0] Iref1 2G Iref12 3G/4G/5G Iref1 0x0
0x0: 250 μA 0x00: 0 μA
0x1: 500 μA 0x1: 150 μA
0x2: 750 μA 0x2: 300 μA
…. ….
1xE: 3750 μA 1xE: 2100 μA
1xF: 4000 μA 1xF: 2250 μA
0x05 ASM_CTRL [7:5] (Reserved) Reserved, set to zero 000 N Trigger 0 Y RW
[4] MBShuntARM 0X00: MB shunt ARM OFF 0
0x01: MB shunt ARM ON
[3:0] Antenna switch state 0x0
0x0: Isolation/Stand-by 0x7: B8
0x1: TRx1 0x8: B26
0x2: TRx2 0xC: Isolation
0x3: TRx3 0xD: Isolation
0x4: TRx4 0xE:LB_ANT terminated
0x5: B20 0xF: LB_2G_TX
0x6: B12 All others reserved
0x0C PA_BIAS2 [7] EnDACOverWrite 0x00: Default 2G_Bias_CTRL[3.0] = 0xF 0 N Trigger1 Y RW
0x01: Enable overwrite 2G_Bias_CTRL[3.0]
[6:4] Reserved Reserved 000
[3:0] 2G_Bias_CTRL 2G PA bias range control 1111
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 28 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 26-3. SKY58091-11 MIPI RFFE Register Map (Common Registers)
Regi
ster
Add
ress
(H
ex)
Register Name Fiel
d Bi
ts
Field Name Description Defa
ult V
alue
BSID
/GSI
D Su
ppor
t
Trig
ger S
uppo
rt
Ext R
eg R
/W
R/W
0x02 Reserved Reserved 0x00 0x03 PA_BIAS1 [7] LTD Limited Bias Mode 0 N Yes
Trigger 1 Y RW
[6:4] (Reserved) Reserved 000 [3:0] Iref1_PB 2G 3G/4G/5G Iref1_PB
Reserved 0x00: 0μA 0x1: 200μA 0x2: 275μA …. 0xE: 1175A 0xF: 1250 μA
0x04 Reserved Reserved 0x00 0x07 CPL_CTRL [7:5] (Reserved) Reserved, set to zero 000 N Yes Y RW
[4:2] CPL_STATE Coupler source and internal direction Trigger 0 000: CPL_OUT disabled 101: Internal coupler Reverse direction 100: Internal coupler Forward
direction 110: External coupler (CPL_OUT from CPL_IN)
All others: Reserved, do not use [1:0] CPL_TERM Internal coupler termination 00 00: Termination A 10: Termination C 01: Termination B 11: Termination D
0x1C PM_TRIG [7] PWR_MODE[1] Note1
Operation Mode 1 Y N
Optio
nal
RW 0: Normal operation (ACTIVE) 1: Low Power Mode (LOW POWER)
[6] PWR_MODE[0] Note2
State bit vector single-bit Powered Reset 0 Y 0: No action (ACTIVE) 1: Powered Reset (STARTUP to ACTIVE to LOW POWER) [5] TRIGGER_MASK_2 Note 3 Mask for TRIGGER_2 0 N [4] TRIGGER_MASK_1 Note 3 Mask for TRIGGER_1 0 [3] TRIGGER_MASK_0 Note 3 Mask for TRIGGER_0 0 [2] TRIGGER_2 Note 4 Transfer data from shadow registers to active registers tied to TRIGGER_2 0 Y [1] TRIGGER_1 Note 4 Transfer data from shadow registers to active registers tied to TRIGGER_1 0 [0] TRIGGER_0 Note 4 Transfer data from shadow registers to active registers tied to TRIGGER_0 0
0x1D PRODUCT_ID Note5
[7:0] PRODUCT_ID 0xED 1110 1101 N N NA R
0x1E MANμFACTURER_ID Note6
[7:0] MANUFACTURER_ID[7:0] Manufacturer ID least-significant bits = 0xA5 1010 0101 N N NA R
0x1F MAN_USID [7:6] Reserved Reserved for future use. Set to all 0. 00 N N Y R [5:4] MANUFACTURER_ID[9:8]
Note7 Manufacturer ID most-significant bits = 01 01 R
[3:0] USID Note8 USID 1101 RW
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 29
Table 26-4. SKY58091-11 MIPI RFFE Register Map (Common Registers)
Regi
ster
Add
ress
(H
ex)
Register Name Fiel
d Bi
ts
Field Name Description Defa
ult V
alue
BSID
/GSI
D Su
ppor
t
Trig
ger S
uppo
rt
Ext R
eg R
/W
R/W
0x20 EXT_PRODUCT_ID Notes5,9
[7:0] EXT_PRODUCT_ID 0x04 0000 0100 N N NA R
0x23 UDR_RST [7] UDR_RST Reset all configurable non-RFFE Reserved registers to default values. The UDR_RST bit shall revert to default value of 0 after software reset is enabled.
0 Y N Y RW
0: Normal Operation 1: Software Reset [6:0] Reserved Reserved for future use. Set to all 0. 000 0000
0x24 ERR_SUM Note10
[7] Reserved Reserved for future error codes 0 N N NA R [6] COMMAND_FRAME_ PARITY_ERR Command Sequence received with parity error – discard command [5] COMMAND_LENGTH_ERR Command length error [4] ADDRESS_FRAME_PARITY_ERR Address frame with parity error [3] DATA_FRAME_PARITY_ERR Data frame with parity error [2] READ_UNUSED_REG Read command to an invalid address [1] WRITE_UNUSED_REG Write command to an invalid address [0] BID_GID_ERR Read command with a BROADCAST_ID or GROUP_ID
Notes for Table 26 Note 1 PWR_MODE[1] defines normal ACTIVE operation and LOW POWER mode. When an RFFE slave is initially powered up and comes out of reset it will go in to ACTIVE but immediately
transition to LOW POWER to avoid requiring a write on the bus to configure devices explicitly to LOW POWER. When the slave is in LOW POWER, charge pumps shall be disabled and the slave shall be listening to the RFFE bus.
Note 2 Writing a 1 to PWR_MODE[0] resets all slave registers to their default settings including the Operation Mode bit in PWR_MODE[1]. Always reads back 0. Note 3 When TRIGGER_MASK_N is set to 1, writes go directly to the active registers. When 0, data is held in shadow registers until the TRIGGER_N bit is set to 1. Note 4 TRIGGER_N has no effect if corresponding TRIGGER_MASK_N is 1. When the part is in LOW POWER and a trigger request is sent in the same command sequence that still keeps the part
in LOW POWER, the trigger request is ignored. This applies to Triggers only, not to Trigger Masks. When the part is in ACTIVE and sent to LOW POWER, or when the part is in LOW POWER and sent to ACTIVE, trigger requests in the same command sequence are NOT ignored.
Note 5 PRODUCT_ID and EXT_PRODUCT_ID are read-only registers. However, during the programming of the USID a write command sequence is performed on these registers, even though the write does not change their value.
Note 6 (same footnote as MANUFACTURER_ID[9:8]) Note 7 Manufacturer ID is read-only. However, during the programming of the USID, a write command sequence is performed on this register even though the write does not change its value.
See http://mid.mipi.org.
Note 8 These bits store the USID of the device. Performing a write to this register using the described programming sequences will re-program the USID. Note 9 (first footnote) Extension to PRODUCT_ID in register 0x1D.
(second footnote is same as PRODUCT_ID) Note 10 The ERR_SUM register reports error codes until read. The ERR_SUM register shall reset after it is read.
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 30 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Evaluation Board DescriptionThe evaluation board is a platform for testing and interfacing design circuitry. To accommodate the interface testing of the SKY58091-11, the evaluation board schematic and assembly
diagrams are included for analysis and design. The basic schematic is shown in Figure 2 for the board assembly in Figure 3.
Figure 2. Evaluation Board Schematic Diagram – SKY58091-11
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 31
Figure 3. Evaluation Board Assembly Diagram – SKY58091-11
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 32 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Table 27. SKY58091-11 Evaluation Board Bill of Material
ITEM QTY REFERENCE DESIGNATORS PART DESCRIPTION
1 REF — SKY58091-11 7.6 x 6.0 MODULE TEST FIXTURE
2 REF — SKY58091-11 7.6 x 6.0 MODULE TEST FIXTURE
3 1 — CONNECTOR, HEADER
4 1 — SKY58091-11 7.6 x 6.0 MODULE TEST FIXTURE
5 21 — CONN SMA END LAUNCH JACK
6 1 C36 CAPACITOR, CERAMIC, 270 pF, 10%, X 7R, 50 V, 0402
7 2 C41,C43 CAPACITOR, TANTALUM MOLDED 220 μF 10 V ±10%
8 3 C7,C2,C39 CAPACITOR, TANTALUM MOLDED 10 μF 16 V ±10% 1206
9 11 R3,R8,C15,C17,C18,C20.C21,C23,C25,C45,C47 RESISTOR, 0 OHM, JUMPER, 0.05 W, 0201
10 5 R4,R5,R6,R7,R10 RES,0 OHM, JUMPER, 0.063 W, 0402
11 1 C12 CAPACITOR,CERAMIC,0.1 UF,10%,X7R,16V,0402
12 1 C8 CAPACITOR, CERAMIC,2.2 UF,10%,X5R,16V,0603
13 1 C9 CAPACITOR, CERAMIC,10 UF,20%,X5R,6.3V,0603
14 1 C6 CAPACITOR, CERAMIC,22000 PF,10%,X7R,16V,0402
15 1 C5 CAPACITOR, CERAMIC,1000 PF,10%,X7R,50V,0402
16 1 C4 CAPACITOR, CERAMIC,0.1 UF,10%,X7R,16V,0402
17 1 C13 CAPACITOR, CERAMIC,1 UF,10%,X5R,10V,0402
18 1 C22 CAPACITOR,CERAMIC,1 PF,±0.1PF,C0G,25 V,MID-Q,0201
19 1 C26 IND,ML-VC,22 NH,3%,MHQ,0201WB
20 1 C27 CAP,CER,22 PF,2%,C0G,50V,0201
21 1 C28 IND,ML-VC,18 NH,3%,HI-Q,0201
22 1 C44 IND,ML-VC,7.5 NH,3%,MHQ,0201WB
23 1 C46 CAP,CER,3 PF,+/-0.1PF,C0G,50V,0201
DO NOT PLACE C10,C11,C14,C16,C19,C24,C29,C30,C31,C32,C33,C34,C35,C37,C38,C40,C42,R1,R2,R9,R11
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 33
Package Dimensions Figure 4 is a mechanical drawing of the layout for the 56-pad SKY58091-11 module. Figure 5 provides a recommended PCB layout footprint for the FEM to help the designer attain optimum
thermal conductivity, good grounding, and minimum RF discontinuity for the 50-ohm terminals.
Figure 4. Dimensional Diagram for 7.6 mm x 6.0 mm x 0.75 mm, 56-Pad MCM Package – SKY58091-11
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 34 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Figure 5. PCB Layout Footprint for 7.6 mm x 6.0 mm, 56-Pad Package – SKY58091-11
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 35
Package Description Figure 6 shows the device pad configuration and the pad numbering convention, which starts with pad 1 in the lower left and increments counter-clockwise around the package. Table 27 lists the pad labels and signal descriptions. Typical case Markings are shown in Figure 7.
Figure 6. SKY58091-11 Pad Configuration – 56-pad MCM (Top View)
Figure 7. Typical Case Markings
Table 28. SKY58091-11 Signal Descriptions Pad No.1 Name Description
2 LB_ANT RF Switch Port to/from Antenna 4 LB_CPL_OUT Built-in or Alternate Coupler Output 5 NC No Connect 6 LB_CPL_IN Input from M/HB Coupler 8 2GHB_TX_OUT High Band 2G PA Tx Output
13 VRAMP 2G PA Analog Power Control Input 14 VBATT Battery Supply
15 & 16 2G_VCC 2G PA Supply 18 SCLK MIPI Clock Input 19 SDATA MIPI Serial Data I/O 20 VIO MIPI Supply 22 2GHB_IN 2G PA High Band RF Input 24 2GLB_IN 2G PA Low Band RF Input 25 NC No Connect 26 4GLB_IN 4G PA RF Input 30 NC No Connect 32 4GLB_VCC 4G LB PA Supply 36 LB_TX4_OUT PA Switch Auxiliary Output 4 37 LB_TX3_OUT PA Switch Auxiliary Output 3 38 LB_TX2_OUT PA Switch Auxiliary Output 2 39 LB_TX1_OUT PA Switch Auxiliary Output 1 44 B8_RX Band 8 Duplexer Rx Output 47 B12_RX Band 12 Duplexer Rx Output 49 B26_RX Band 26 Duplexer Rx Output 51 B20_RX Band 20 Duplexer Rx Output 53 LB_TRX4 Auxiliary Antenna Switch Port TRx4 54 LB_TRX3 Auxiliary Antenna Switch Port TRx3 55 LB_TRX2 Auxiliary Antenna Switch Port TRx2 56 LB_TRX1 Auxiliary Antenna Switch Port TRx1
1 Pads 1, 3, 7, 9-12, 17, 21, 23, 27-29, 31, 33-35, 40-43, 45, 46, 48, 50, 52 are Ground pads
Electrostatic Discharge Sensitivity
To avoid ESD damage, both latent and visible, it is very important that the product assembly and test areas follow the ESD handling precautions listed below. • Personnel Grounding
- Wrist Straps - Conductive Smocks, Gloves and Finger Cots - Antistatic ID Badges
• Protective Workstation - Dissipative Table Top - Protective Test Equipment (Properly Grounded) - Grounded Tip Soldering Irons - Solder Conductive Suckers - Static Sensors
• Facility - Relative Humidity Control and Air Ionizers - Dissipative Floors (less than 1,000 MΩ to GND)
• Protective packaging and Transportation - Bags and Pouches (Faraday Shield) - Protective Tote Boxes (Conductive Static Shielding) - Protective Trays - Grounded Carts - Protective Work Order Holders
-
PRELIMINARY DATA SHEET SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 36 December 5, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 205267E
Package Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly.
The SKY58091-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to Skyworks Application Note, PCB Design and SMT Assembly/ Rework Guidelines for MCM–L packages, Document Number 101752.
Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format (Figure 8)
Figure 8. Carrier Tape Dimensional Diagram for Body Size 6.0 mm x 7.6 mm – Overmold MCM
-
SKY5®-8091-11 SkyOne® LOW-BAND TX-RX FRONT-END MODULE PRELIMINARY DATA SHEET for 3G/4G/5G APPLICATIONS and LOW BAND / HIGH-BAND 2G
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 205267E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 5, 2019 37
Ordering Information
Part Number Part Description Evaluation Board Part Number
SKY58091-11 SkyOne® Low-Band Tx-Rx Front-End Module SKY58091-11EK1
Revision History
Revision Date Description
A January 28, 2019 Initial Release – Preliminary Information CN 28932
B May 11, 2019 Revise: Features list, Description (p1); Tables 3, 5, 6, 11, 13, 14, 16, 18, 21, 23, 26, 27; Figures 2, 3 CN 32962
C July 26, 2019 Revise: 4G Features (p1); Description (p1);.Tables 3, 4, 6, 8–23, 25, 26; Figure 2 CN 35847
D October 31, 2019 Revise: Removed “and Confidential” from running footer. Publishing to external web site CN 40458
E December 5, 2019 Revise: Spec updates; Tables 2, 5, 13, 15–17, 19, 21–23, 26, 27; Figure 7 CN 40500
References Skyworks Application Note: PCB Design and SMT Assembly/Rework Guidelines for MCM–L Packages; Document Number 101752
Standard SMT Reflow Profiles: JEDEC Standard J-STD-020
Testing & Measurement Techniques-Electrostatic Discharge Immunity Test, IEC 61000-4-2
Electrostatic Discharge Sensitivity (ESD) Testing: JEDEC Standard, JESD22-A114 Human Body Model (HBM)
Electrostatic Discharge Sensitivity (ESD) Testing: JEDEC Standard, JESD22-A115 Machine Model (MM)
Copyright © 2019, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol and SkyOne are trademarks or registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.